Search Results

Search found 9462 results on 379 pages for 'laptop repair'.

Page 125/379 | < Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >

  • Atheros AR928X wireless connection makes neighbourhood machine drop off line

    - by funicorn
    I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

    Read the article

  • Music server + Banshee

    - by slosd
    I'm currently trying to figure out some kind of set-up for my music collection. The music collection is located on my "main PC" and I'm using Banshee to play/manage the music. Since I'm often at a different location where I use my laptop I have a FTP server running on my main PC, use curlftpfs to mount the music in /home/username/Music and sync the Banshee DB/configuration via Dropbox. The problem at the moment is that Banshee skips songs very often when the connection is a little slower. I've been looking at some servers like Ampache but they are not really an option since they don't let me use Banshee (which means I have no ability to change metadata or rate songs). Syncing the whole collection to my laptop isn't an option either because of its size. It would be great if you had some ideas how to make my current set-up more reliable or maybe know an alternative.

    Read the article

  • Help with Kodak esp 3250 printer driver on Lubuntu 12.1 SOLVED!

    - by user108608
    First my system: pentium 4 -don't remember the speed-, 1g ram, dual boot to separate physical drives, Fdos and Lubuntu 12.1 second my lan: I have four computers operating for the same printer. 1. Intel quad core i5, 4g ram, running Windoze 7 64 bit, printer connected and shared from here. Kodak ESP 3250 2. Gateway 17" laptop running Windoze 7 32bit 3. Asus tablet (small laptop) running Lumbutu 12.1 4. My dual boot system running Fdos and Lubuntu 12.1 The problem: I downloaded c2esp_25c-1_i386.deb, tried to install it using DEBI Package Installer, it loads the files, looks for cups driver and ends with an error: "Dependancy is not satisfiable: libcupsdriver1 (=1.4.0)" What do I do now? Is there some place that I can get the correct cups driver? further information: The Asus tablet was running Ubuntu 12.1 (very slowly and with a few crashes) and could print from the lan printer with no problems. Is there something in Ubuntu that can be loaded into Lubuntu? noobee user hoping for answers, Paul

    Read the article

  • nVidia GeForce Go 7600? can it ever run unity?

    - by Khaled Musleh
    my laptop Toshiba Qosmio G30 has nVidia GeForce Go 7600 card and it suppose to support 3D . i run unity 2d now . I run 12.04 and the graphic driver is--VESA: G73 Board - toshg73m-- by UBUNTU. when i run /usr/lib/nux/unity_support_test -p then i get this list Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no the card is not blacklisted but a similar one with GT is! Do you think that there is a chance the laptop can run the unity 3d? and may be i could change the resolution of the screen to a higher one too! I tried all the nvidia drivers provided but none works (except 96 in ubuntu 12.04 ). i get a black screen or terminal screen. best wishes to all

    Read the article

  • magic trackpad - Ubuntu

    - by UbuntuGuy
    I've been using a mac in my job for a while now. The only feature i like about it above my ubuntu (on an hp) is the trackpad. I love doing the strokes to move between different files. It really makes things quicker. Is it possible to imitate this feature on my ubuntu laptop. (like maybe there might be something that utilizes my mouse pad on the laptop, as well as the scroller) If that is impossible or doesn't exist then can i set up a magic trackpad to ubuntu on my hp.

    Read the article

  • Extremely slow transfer speed ubuntu -> Windows

    - by Hailwood
    I have two laptops, One is running Ubuntu 12.04 (EXT4) the other is running Windows 7 (NTFS). I am copying over 40gb of data (one file) from the Ubuntu laptop to the Windows Laptop. (Browse the shared folder on Ubuntu using Windows copy/paste) But I am getting transfer speeds topping out at ~700kb/s Surely this is not right. I am transferring via wifi on both laptops. My download speeds can reach 7-8mb/s on both laptops, so I know it is not the wifi cards or the router topping out. wlan0 Link encap:Ethernet HWaddr 84:4b:f5:db:b4:85 inet addr:192.168.1.66 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::864b:f5ff:fedb:b485/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11941185 errors:0 dropped:0 overruns:0 frame:0 TX packets:11306693 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10087111370 (10.0 GB) TX bytes:7843524888 (7.8 GB)

    Read the article

  • How to close lid without triggering standby one time only

    - by Ian Mackinnon
    Related: How can I tell Ubuntu to do nothing when I close my laptop lid? I have my laptop set to activate standby when I close the lid. I want to keep this as the default for both battery and AC power. But occasionally I want to close the lid without triggering standby (eg. while just listening to audio). Is there someway I can tell Ubuntu, "I'm going to close the lid now. Don't stand by this time", without altering the defaults (because I almost always forget to change them back).

    Read the article

  • Wifi won't work without ethernet (Ubuntu 12.04)

    - by alok
    I have a strange problem. I am running Ubuntu 12.04 on a Dell Studio 1558 laptop. I'm usually unable to access Wifi (I have a BCM43224 wireless card with the STA proprietary driver installed.) So I have to unplug the ethernet cable from my Wifi router and stick it into my laptop's ethernet port to access the Internet. But when I stick the cable back into the Wifi router and try connecting to Wifi, Wifi inexplicably starts working. How can I get Wifi to work all the time without having to 'jumpstart' it with an ethernet connection?

    Read the article

  • Which version of ubuntu is compatible with ACER Aspire 5732Z?

    - by Mehdi Bateni
    I have an ACER Aspire 5732Z Laptop, and 6 days ago I have installed Ubuntu 11.10 on my laptop, But I found black screen in login. I have tried a lot of ways to solve this problem, but there is no way. So can you tell me which version is compatible with this ACER Aspire (5732Z)? Detail: Intel-Pentium-processor T4400 (2.2 GHz, 800 MHz FSB), Intel-GMA 4500M, 15.6" HD LCD, 2GB Memory, 320 GB HDD, Acer Nplify(TM) 802.11b/g/n. Thank You. .. And finally, I found that Linux Mint is best for my ACER-ASPIRE5732Z. It is also compatible with Ubuntu codes, because as I know it is base on Ubuntu.

    Read the article

  • Ubuntu 12.04 LTS x86_64 sound artifacts when scrolling with firefox

    - by Nh3xus
    I've been using Ubuntu since the 10.04 LTS version and i have a sound problem that still remain in my fresh install of the 12.04 LTS AMD64 version. This install has been performed by formatting the / partition and my documents were kept safe in the separated /home partition. The problem : When i listen to a audio or video source while browsing the web with Firefox, I have some sound artifacts when i'm scrolling and stops when i'm not doing it. This happens when i'm doing X11 related actions too, such as switching between virtuals desktops. Computer configuration of my laptop : - Ubuntu 12.04 LTS AMD64 - Plantronic USB Headphones - Intel HDA Audio sound card (laptop) with SigmaTel STAC9200 chip - AlsaMixer v 1.0.25 - Nvidia GeForce 7950 GTX with Nvidia 295.40 driver Any advices are welcome here :) Note : This is my first post on AskUbuntu.

    Read the article

  • is it possible for windows viruses when downloaded through ubuntu affect my windows os

    - by fr33c0untry
    I know that Ubuntu is immune to virus so there is no question of it getting infected while browsing the net.however i frequently transfer files from my pendrive (which i get from other virus infested computers) to my own laptop and save it on the data drive which is shared by both windows and ubuntu.i would like to know if there is a chance for windows viruses which might get saved and then infect it whenever i switch to windows later on.its ironic that i scan my pendrive using avast on windows and then save all my files to my hard drive to keep my laptop free from virus eventhough i have ubuntu.can anyone suggest an alternative.thanks in advance.

    Read the article

  • install matlab 2013a with error

    - by user158449
    I tried to install Matlab2013a in my laptop (Ubuntu system). I download a ISO file (very big) and followed their instruction: mount it and run "install". But it returns me an error: Cannot locate Java Runtime Enviroment (JRE). The directory ~/Matlab/sys/java/jre/glnx86/jre does not exist. In the folder ~/Matlab/sys/java/jre/, what I have is "glnxa64". Does that mean that I can't install this version of Matlab in my 32bit laptop? This java comes from Matlab. How should I get it work?

    Read the article

  • WUXGA revisited

    - by John Paul Cook
    I previously blogged about my search for a 17” 1920x1200 laptop. The only one I could find was a 17” MacBook Pro, which has been an excellent machine for running Windows and SQL Server. It is no longer made. Apple has a few refurbished ones available. Just be sure to get a matte display if you buy one. If you want WUXGA resolution or better in a laptop, your only off the shelf option is now the 15” MacBook Pro with the Retina display, which is 2880x1800. This exceeds the resolution of my 30” 2560x1600...(read more)

    Read the article

  • How do I avoid the "S to Skip" message on boot?

    - by Marty
    After upgrading my laptop from karmic to lucid, my fat32 partition won't mount automatically. I get the message: The disk drive for /osshare is not ready yet or not present Continue to wait; or Press S to skip mounting or M for manual recovery Funny thing is, if I skip, then /osshare/ is mounted once I log in. I've a similar setup on my desktop, and it works fine. Fstab on desktop: UUID=4663-6853 /osshare vfat utf8,umask=007,gid=46 0 1 /etc/fstab on laptop: UUID=1234-5678 /osshare vfat utf8,auto,rw,user 0 0

    Read the article

  • Ubuntu scrollbars don't render on Cygwin X server

    - by David M. Karr
    I have an ubuntu 12.0.4 desktop. I have a Win7 laptop running Cygwin. I can display windows from the Ubuntu box on the Win7 laptop using the Cygwin X server, but the window is somewhat "degraded". Specifically, scrollbars are not rendering properly. I've used Ubuntu before, but this is the first time I've seen these odd scrollbar popups that are used in 12.04. I'm guessing the Cygwin X server is having trouble rendering that for some reason. In the Cygwin view, I see the slightly thicker vertical bar, but when I hover the mouse over it, nothing happens. I'd really prefer to get conventional scrollbars. Can I configure Ubuntu 12.0.4 to do this, which might result in Cygwin being able to display them?

    Read the article

  • adjust resolution on Ubuntu Server 10.04?

    - by Mike Grace
    Installed Ubuntu Server 10.04 on an old laptop and I noticed that the system is trying to show the CLI below my screen. This means that if I run a script or a program with a bunch of output, once it is done, I have to press return several times to bring the output to the point where I can actually see it on the screen. I also have to clear the screen to be able to see what I am typing at the current command prompt. The laptop is an EliteGroup 536S with a native screen resolution of 1024 x 768 How can I adjust the resolution for Ubuntu Server 10.04? What file do I need to edit if editing a file is the solution? I've seen posts on how to change the resolution on the desktop version of Ubuntu but not the server version.

    Read the article

  • Infrared usb adapter not hot pluggable?

    - by A. Goossens
    For transferring exercise files from my Polar heart rate monitor i use the software Protrainer 5 with an external infrared usb adapter. Using Wine to run Protrainer 5 and some adjustments mentioned here (using irda-utils) i managed to make it work. Well, sort of: every time i want to transfer exercise files and the adapter is not plugged in i have to reboot my laptop with the usb adapter plugged in to make it work. Since i have a laptop it unfortunately is no option to just always leave the adapter in. It seems to me that the usb adapter isn't hot pluggable (which seems odd for a usb device) or there must be another problem. Polar WebLink (other software to transfer exercise files) experiences the same issue. Can anyone help me to fix this problem? Infrared usb adapter: Polar IRDA USB adapter OS: Ubuntu 12.10 (64-bit) Hardware: Lenovo Thinkpad T500

    Read the article

  • Giant battery consumption with dual graphics solution (only i-gpu working)

    - by Noel
    I use a Laptop with Intel Core i7 SandyBridge and integrated Intel HD3000 graphics as well as a Nvidia Geforce GTS 555M. So far, I got the impression my Laptop was running with the Nvidia graphics adapter only because the fan was always running on highest speed (and loudest noise) and it was getting very hot even when doing nothing. Also the battery is empty after ~40-50 minutes (while having ~4-5 hours with Intel graphics in Win7). Since this can't be healthy I wanted to switch to the integrated graphics instead. I was fairly surprised when the System Information showed me that the as graphics adapter I use "Intel M". Why is my battery empty so fast with Ubuntu? Without using the NVIDIA graphics adapter? Summary: I DONT WANT to use the Nvidia graphics adapter (OPTIMUS), I just want the Intel solution. As I have understood, the Intel solution is running already, emptying my battery 10x as fast as Win7. What is wrong? Any ideas?

    Read the article

  • How can I figure out why Suspend sometimes fails?

    - by Isaac
    Something is causing suspend crash occasionally. When it does crash, the system freezes with a black screen and stays on, not suspending. This makes me have to hold the power button until the system shuts down. One setting difference I have from most people is, I don't use the option that lets you suspend when the laptop lid is closed. So opening and closing the laptop lid has no actions. I like to press suspend manually. Could this preference change be the cause? How can I start looking for what's causing the crash, since the crash doesn't display errors?

    Read the article

  • How to switch off wifi on startup or from the console

    - by mit
    I have installed ubuntu 10.04 on a laptop. Wifi is switched on by default on startup. I can disable it rightclicking the network manager icon in the gnome bar. How can I set it to have wifi switched off as default? Alternatively, how can I switch off wifi on the console? I tried already the rfkill command but it does not list any devices and it does not switch off wifi, I tried different parameters. This is a standard install of the Ubuntu 10.04 i386 Desktop Live CD on an IBM T40 Laptop. EDIT A: This is the output of some rfkill commands on my system, and it does not affect the wifi of the laptop: $ rfkill --help Usage: rfkill [options] command Options: --version show version (0.4) Commands: help event list [IDENTIFIER] block IDENTIFIER unblock IDENTIFIER where IDENTIFIER is the index no. of an rfkill switch or one of: <idx> all wifi wlan bluetooth uwb ultrawideband wimax wwan gps fm $ rfkill list $ rfkill list wifi $ rfkill list all $ rfkill list wlan $ sudo rfkill list all $ sudo rfkill block all $ sudo rfkill block wlan $ sudo rfkill block wifi $ EDIT B: Now I found out that sudo ifconfig eth1 down turns it off. And I can turn it on through the gnome network applet again. But the applet does not reflect the change from the commandline, it stills believes wifi is switched on. I have to switch it off and on again on the applet to switch it on again, when I switched it off from the console. Is there a better way? This is what the syslog looks like when I switch wireless off and on again from the network manager: NetworkManager: <info> (eth1): device state change: 3 -> 2 (reason 0) NetworkManager: <info> (eth1): deactivating device (reason: 0). NetworkManager: <info> Policy set '24' (eth0) as default for routing and DNS. NetworkManager: <info> (eth1): taking down device. avahi-daemon[660]: Withdrawing address record for fe80::202:8aff:feba:d798 on eth1. kernel: [ 971.472116] airo(eth1): cmd:3 status:7f03 rsp0:0 rsp1:0 rsp2:0 NetworkManager: <info> (eth1): bringing up device. NetworkManager: <info> (eth1): supplicant interface state: starting -> ready NetworkManager: <info> (eth1): device state change: 2 -> 3 (reason 42) avahi-daemon[660]: Registering new address record for fe80::202:8aff:feba:d798 on eth1.*. kernel: [ 965.512048] eth1: no IPv6 routers present

    Read the article

  • Remote GDM login

    - by luri
    Is it possible to remotely (via ssh) make a login to GDM? I'll explain a situation in which I'd need this: I'm on my laptop and connect to my desktop via ssh. I realize there are some updates available. I install them all, but I need to reboot the computer. The problem is that once the desktop has rebooted, there will be no GDM session available, since it's necessary to log in. Can I somehow perform the GDM login remotely from my laptop? Edit: I can't find FreeNX for Maverick, and I haven't been able to configure x11vnc + vncviewer to work. Isn't there an easy way?

    Read the article

  • What would I do to figure out why Suspend sometimes crashes?

    - by Isaac
    Something is causing suspend crash occasionally. When it does crash, the system freezes with a black screen and stays on, not suspending. This makes me have to hold the power button until the system shuts down. One setting difference I have from most people is, I don't use the option that lets you suspend when the laptop lid is closed. So opening and closing the laptop lid has no actions. I like to press suspend manually. Could this preference change be the cause? How can I start looking for what's causing the crash, since the crash doesn't display errors?

    Read the article

  • How to control / disable low level battery on bluetooth mouse

    - by Alberto
    I have a little problem with my Kesington Bluetooth Mouse on Ubuntu 12.10. Ubuntu 12.10 considers my bluetooth mouse battery as a system battery as if it was the main laptop battery (so I have two on the battery indicator, the main and the bluetooth one). When it runs low level, near to die, battery, my laptop acts as if it was the main battery and I must quickly stop bluetooth and continue on the touchpad if I want to work. Can anyone help me? Maybe I prefer to disable the battery control over the mouse, I don't care about it, I know it is fully charged, but Ubuntu always starts on 33% or less, I just want to work with it and when it will be battery-off I will recharge the batteries. Many thanks in advance. Alberto.

    Read the article

  • Alfa AWUS036H USB wireless adapter not recognized

    - by GFiasco
    The Alfa AWUS036H USB wireless adapter will not be recognized by my netbook (Ubuntu 14.04, Asus X201E). As I understand it, the drivers should already be built in to this version of Linux, but I tried a make/make install of the latest Realtek drivers (as mentioned on How do I install drivers for the Alfa AWUS036H USB wireless adapter?) and it didn't work. I then followed the advice of this thread (ALFA AWUS036NH driver) and did a make/make install of the most up-to-date backport of the drivers, but that didn't work. At this point I tried a series of commands from this thread (http://ubuntuforums.org/showthread.php?t=2187780) in an attempt to identify the problem, but at no point could I get the laptop to ever recognize the USB adapter. I have also troubleshot the USB cable itself, tried both the USB 2.0 and 3.0 ports on the laptop, have never received an error message regarding a need to update the firmware, and have seemingly successfully installed all manner of variation of Realtek drivers which were supposed to make the adapter work. (I also tried to delete/clean up after each install, in the hope I wasn't making things worse.) Not sure what I should do next. Please let me know if I need to post any more information. Thanks very much for your help. EDIT: Before inserting Alpha USB adapter: :~$ lsusb Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:570c Realtek Semiconductor Corp. Bus 001 Device 026: ID 13d3:3393 IMC Networks Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 03f0:3112 Hewlett-Packard Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub After inserting Alpha USB adapter (USB 3.0 port, no change): :~$ lsusb Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 004: ID 0bda:570c Realtek Semiconductor Corp. Bus 001 Device 026: ID 13d3:3393 IMC Networks Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 03f0:3112 Hewlett-Packard Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Ran tail -f /var/log/syslog, inserted device, no recognition (last entry is dated 16:17:01, so an hour ago). Going to check on an Ubuntu 14.04 laptop and Windows XP desktop. I'll update after. Thanks for your help to this point.

    Read the article

  • No lock screen when the right click menu is open

    - by Shivram
    I just found that the lock screen on my laptop does not show up when the right click menu is open. I discovered this when I pressed the right click button accidentally while closing the lid and the laptop went to sleep, but the lock screen never showed up when I opened the lid again. I am also not able to lock the system manually(with ctrl+alt+L) when the right click menu is open. Is this by design or is it a bug? I would assume that the screen should be locked automatically when the computer goes to sleep, but this doesn't seem to be the case. Anyone have any suggestions? My specs are: Dell Vostro 1500, Ubuntu 12.10

    Read the article

< Previous Page | 121 122 123 124 125 126 127 128 129 130 131 132  | Next Page >