Search Results

Search found 34495 results on 1380 pages for 'network and internet'.

Page 126/1380 | < Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >

• Slow network file transfer (under 20KB/s) on newly built x64 Win7

  - by Mangoshake

  I am getting <20KB/s for local network file transfer. If I transfer a very small file (less than 100KB) it would start quickly then slow down to <20KB/s. all subsequently network file transfer would be slow, a reboot is needed to reset this. If I transfer a large file it would be stuck on calculating for a long time and then begin with <20KB/s immediately. This is a newly built desktop running Windows 7 x64 SP1. Realtek gigabit LAN from the motherboard (ASRock Extreme3 gen3). Problematic speed is observed on the private LAN, both through ethernet and WiFi. The Router is D-Link DIR-655. Remote Differential Compression is off. Drivers are up-to-date from ASRock's website. I have tested network file transfer to and from another Windows 7 laptop and a MacBook Pro, so I am fairly certain it is the desktop's problem. The slow speed only happens with one direction also, outbound from the desktop, regardless of whether I initiate the file transfer action from the origin or the destination. Inbound network file transfer and internet speeds are fine, so I don't think this is a hardware issue. I am getting 74.8MB/s internet upload speed from speedtest.net (http://www.speedtest.net/result/1852752479.png). Inbound network file transfer I can get around 10-15MB/s. I am hoping this community has some insight for me to troubleshoot this. I don't see anything obviously related from the Event Viewer, and beyond that I just don't know where else to look. Any suggestions are greatly appreciated, thank you in advance.

  Read the article

• Vista Enterprise doesn't find logon servers in a network with 802.1x authentication

  - by jneves

  In a network with 802.1x configuration and a samba server configured in the domain, I have a radius server that delegates the authentication against the samba domain for users (using LDAP). The radius defines which VLAN the user is supposed to have access. I'm trying to put a Windows Vista Enterprise in the same network, but it attempts to logon the domain before authenticating against the network in 802.1x and it doesn't find any logon servers. In the radius logs I see the machine trying to authenticate with 'host/'. Does Vista enterprise require that I put it in a network with access to the logon server at that point? Thanks in advance, João Miguel Neves

  Read the article

• One Mac computer with multiple network connections?

  - by Kyle Lowry

  I have a Mac (OS X 10.5) that I would like to connect to a dedicated/isolated Internet connection (one that is not connected to the LAN), and a LAN. The LAN is set up with its own, separate, Internet connection which is shared by several dozen computers (and is quite slow). I want to set it up so that the Mac uses its own dedicated Internet connection (on a different account with a different company) for its Internet access, but can still access the local area network as well. How can I configure the Mac & the network to allow this?

  Read the article

• Network driver for Hyper-V restore from Windows Home Server

  - by Philipp Schmid

  I have backed up Windows Server 2008 running virtualized on Hyper-V to a Windows Home Server 2008 SP1 (I know I should have backed up the VHD instead). Now I need to restore the contents of the VM from WHS. I have created a restore CD ISO and used it to create a new VM. It all works as advertised up to the point where the restore process wants to load the network drivers (it only finds 4 disk drivers on the restore CD. but no network drivers). So I created a virtual floppy and copied the contents of 'Home Server Drivers for Restore onto it. But no luck! I have tried moving the 4 subdirectories into the root of the floppy, but that didn't work either. Finally, I started another instance of the WS 2008 to identify the network driver that the virtualized instance is using (%WINDOWS%\system32\drivers\netvsc60.sys) and copied that file onto the virtual floppy, without success. Does anyone have any suggestions on how to get networking working on a Hyper-V instance running off the Windows Home Server Restore CD? UPDATE: As suggested by delenda, I have added a legacy network adapter to my VM, and indeed I now get a network driver listed! However, the WHS it still not found, even after entering the home server name manually. PHS

  Read the article

• Recommendations for colocation in the US

  - by Emil

  Hello serverfault I work for a European media company and we are currently looking for colocation in the US. I know the European market quite well unfortunately that is not the case for the US. I'm hoping for you guys to help me out a bit with a few questions, it would be much appreciated! I am looking for a data center that can deliver a high level of availability (tier 3 or better). The installation will be fairly large so capacity is important. Good internet connectivity/carrier presence. However most important is good customer support, skilled dedicated and responsive technical staff, since we won't have tech staff close by. I'm looking for a small and fast moving company that target internet businesses rather than big old enterprise hosting. What locations should we go for given that we want to reach all of the US from a single site and still maintain decent latency? (do we need east and west coast?) Where are the main internet hubs and should you try and get as close as possible? Are there any good online resources I should look at? Where do the large scale internet/media services colocate? Lastly I would be very happy to get some actual recommendations for companies to talk to P.S I'm happy to return the favor if anyone has question regarding data centers and colocation in Europe.

  Read the article

• Shrew VPN Client gives default route- changing the policy stops me from accessing VPN network

  - by Lock

  I am using the shrew client to connect to what I believe is a Netscreen VPN. Now, when connected, the client adds the VPN as the default route. I do not want this- there is only 1 network behind the VPN that I need to access. I found that with the shrew client, you can change the "Policy" settings on the connection, and can add your own networks in that should tunnel over the VPN. I do this, and add my network in, but when I connect the VPN, I get nothing. Can't access the network. Any idea why this would be? I can see my network in the routing table, and its correctly pointing to the correct gateway. A traceroute shows all time-outs, so I can't be 100% sure that it is trying to tunnel over the VPN. Any idea how I can troubleshoot this?

  Read the article

• How to stop Windows 7 from automatically connecting to unsecure wifi network

  - by Remi Despres-Smyth

  One of my neighbors has an unsecure wifi network called WLAN. At one point in the past, I accidentally connected to it, and disconnected immediately when I noticed. Now, when I open my laptop at home, it sometimes connects to the WLAN network first, before trying my (secured) home wifi network. The information I've found regarding this issue seems to suggest this network should have a profile on the "Manage wireless networks" screen - but it does not. How do I tell Windows 7 to never connect to networks with SSIDs called WLAN? Or to never connect to unsecured networks without confirming with me first?

  Read the article

• Wireless Network Disappearing From Available Networks (Windows 7)

  - by PeteDaMeat

  I have been using Windows 7 with a BT Voyager wireless adapter to connect to my home wireless network for around the last 6 months or so and until recently have experienced no problems. However, over the last couple of days Windows has been unable to connect to the network and the network name is no longer visible in the list of available wireless networks. The only way I have got round the problem is to reboot the NetGear router and to change the SSID to a network name which has not already been used. I do not believe the problem is with the router as my mobile phone can connect to it without any problems. The BT Voyager wireless adapter detects all other available networks so I presume this is a Windows 7 issue as it seems to occur when the PC is rebooted. This problen has happened twice in the last 2 days and is becoming extremely annoying. Does anyone have any suggestions?

  Read the article

• Internet doesn't work when enable local Lan

  - by rakesh yadav

  We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: B1) WAN interface (192.168.0.2) ( Used for internet) B2) LAN interface (192.168.1.2) ( used for local connectivity) when i keep both LAN Enabled than my internet doesn't work, but if I disabled my local Lan than internet working fine. so please help me how can resolved this issue or should i need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

  Read the article

• Home workers requiring simultaneous office VPN and local network access

  - by jon.simpson.uk

  I now have a large number of remote users that are using a Check Point Secure Client VPN connection into the office. These users also need access to network resources attached to their local router/hub (network storage and network printer). Is there any way that the client (Windows 7 or XP) can be configured to bypass the VPN for local addresses (192.*)

  Read the article

• How to choose which network connection provides the default gateway in Windows XP

  - by Cathy

  I have a laptop with an integrated NIC and a WiFi connection. Both the wired and wireless networks I am using can access the Internet. Win XP is routing all traffic through the wireless network. I want to force it to route everything through the wired network when it is available (i.e. when I am sitting at my desk with the laptop docked) and through the wireless when that is the only option (i.e. when I have undocked my laptop and carried it to a conference room, or if I am out of the office working on a different WiFi network). The wireless connection cannot be established until after I am logged into Windows, so it's always the second network to become available to the OS. I have manually overridden the metric values in the TCP/IP configurations so that the NIC has metric 10 and the WiFi has metric 20. However, Windows is still picking the WiFi adapter's address as the Default Gateway, so this isn't helping. If I manually disable and re-enable the WiFi adapter, then it will switch the default gateway to the wired network and stay that way until I shutdown Windows. How can I tell Windows XP not to replace the default gateway when the WiFi connection is first enabled?

  Read the article

• XenServer VM's lose network settings

  - by Ash

  We deploy virtual machines using Citrix XenServer 6.0 for our clients. Two seperate clients experience the same issue: when a Server 2008 virtual machine is restarted, the static IP addresses (network address, subnet, gateway, primary DNS) don't appear to apply correctly as the IP's cannot be pinged, network services cannot be accessed etc. The issue is resolved by manually switching the network adapters to DHCP, then re-setting them to the original static IP's. While not a major issue, it's a pain when restarting servers due to Windows Updates, plus iSCSI drives need to be manually connected to Windows again via iSCSI Initiator. We have tried removed the network adapters from the virtual machine under XenCentre but without luck. Anyone experienced similar issues?

  Read the article

• open source solution to a gateway for a network of a housing cooperative of 150 people

  - by SirDinosaur

  i just inherited a barely functioning network for a student housing cooperative of about 150 people. in it's current state, as i understand it from the previous person in charge of the network, we have working wireless access points and working ethernet cords going to working gigabit switches going to a barely functioning gateway (right now a simple home router) to one of three possible outbound connections. it is possible to connect to the network through the wireless or ethernet, but especially during peak hours, packets / connections are likely dropped or otherwise get no response. my intuition tells me to replace the gateway with something that can handle multiple outbound connections (WAN) and one inbound connection (LAN), while the rest of the network seems suitable for now. i'm somewhat knowledgable in Linux (been using Debian after first Arch Linux) and i want to use as much open source as possible, but i'm confused whether or not a simple server that i could easily understand will work for this situation. do i need specialized hardware to handle the switching more effectively? if so, what are my options? (i found this, thoughts?) or if a Debian server would work, anything else i should about the specs required for this type of server? also links to any useful information on using open source to maintain this type of network would be most appreciated. <3 P.S. crossposted http://redd.it/yybp2.

  Read the article

• Teamed network cards on a Proliant Server

  - by Matt

  We have 4 network cards in a Proliant server with Server 2008R2 running Exchange 2010, with 1 card set to a static IP address and the other 3 set to DHCP. I just need some clarification as I have not teamed network cards. Do all the network cards need to have a static IP when I set as a team. The connection that has the static IP is the IP that I need to use for the Server. Is it possible to set the teamed cards to the same static IP or do I have to change the static IP to another IP then use it for the teamed IP? I will be using HP Network Configuration Utility to set this up.

  Read the article

• How to connect a Bluetooth network connection using the command line

  - by Ed Guiness

  I can enable a Local Area Network interface for my machine with the command netsh interface set interface "Local Area Connection" ENABLED Is there an equivalent command to connect a bluetooth network connection? I've tried netsh interface set interface "Bluetooth" ENABLED but it seems to have no effect, the connection remains disconnected. I also tried netsh interface set interface "Bluetooth" connect=CONNECTED but this returns One or more essential parameters not specified I know this Bluetooth connection is otherwise ok since I am able to connect using Control Panel Network Connections, right-clicking on Bluetooth Connect.

  Read the article

• Domain Controller died, now get authentication boxes in IE for SDL Tridion 2009

  - by Rob Stevenson-Leggett

  We had a major network issue where our secondary domain controller (responsible for Win2k3 boxes) died and had to be rebuilt (I beleive this is what happened, I am a developer not network admin). Anyway, I am working remotely via VPN at the moment and since this happened, I am getting an authentication box when trying to access certain areas of SDL Tridion via IE (Tridion 2009 SP1 is IE only) it seems like somewhere my credentials are not being passed correctly or the ones cached on my laptop do not match the ones the Domain Controller has. This only seems to affect Windows 2003 servers. Our IT support thinks that the only way to sort it out is to connect my laptop directly to the network. I am not planned to go to the office for a few weeks at least and this issue means I have to work with Tridion via Remote Desktop. We thought changing the password on my account might work but this didn't help. So basically my question is, is there any way I can reset my credential cache without having to reconnect to the network? Or is it IE that is causing the problem perhaps, since I can RDP to servers and use Tridion 2011 instances in other browsers fine? I am on Windows 7 using SonicWall VPN client.

  Read the article

• Connecting 2 different subnet masks

  - by Jonathan

  I'm no network genius, but I have managed to get most things running. I get confused about subnets and gateways though. We have an office server connected to around 20 PC's that all communicate fine. We have just gotten a cutting machine that won't connect to our network. The server has DHCP, but that fails on the cutting machine, so I've been trying to set the IP manually. Server details are as follows: IP: 10.1.1.12 SUBNET: 255.255.255.0 GATEWAY: 10.1.1.1 Internet connection is via the modem which is 10.1.1.1 An office PC is ussually set up through DHCP and has the following settings: IP: 10.1.1.36 SUBNET: 255.255.255.0 GATEWAY: 10.1.1.1 PRIMARY DNS: 10.1.1.12 Cutting Machine computer has 2 network ports. 1 is specifically for the communication between the PC and the cutting machine. It's details must be as follows: IP: 10.100.100.2 SUBNET: 255.255.255.252 GATEWAY: BLANK The other network port need to connect to the server. I was told that the IP and SUBNET need to be as follows: IP: 10.100.100.1 SUBNET: 255.255.255.252 GATEWAY: ?? How can I connect this port to the server and/or the internet. If anyone can offer assistance, it would really be appreaciated.

  Read the article

• windows 8 network cant connect to other computers

  - by Sickest

  we just setup a windows 7 ultimate file server, and all the other computers on the network, found the server expect the windows 8 computer. computers on the network: vista, win 7 ultimate, mac os, win 8 (problem) I setup a homegroup on the win 7 server pc, but the windows 8 computer can't find the homegroup, nor can it connect to the server by typing its network ext //server-pc i've tried to turn on all the windows 8 sharing to discovery ON, on Private and Public and all Networks, and got nothing. should be noted that the computer is using norton firewall/AV, im not sure if that's a factor

  Read the article

• Administrator view ALL mapped drives

  - by kskid19

  In my understanding of security, an administrator should be able to view all connections to and from a computer - just as they can view all processes/owner, network connections/owning process. However, Windows 8 seems to have disabled this. As administrator running an elevated in Win Vista+ when you run net use you get back all drives mapped, listed as unavailable. In Windows 8, the same command run from an elevated prompt returns "There are no entries in the list". The behavior is identical for powershell Get-WmiObject Win32_LogonSessionMappedDisk. A workaround for persistent mappings is to run Get-ChildItem Registry::HKU*\Network*. This does not include temporary mappings (in my particular example it was created through explorer on an administrator account and I did not select "Reconnect at sign-in") Is there a direct/simple way for Administrator to view connections of any user (short of a script that runs under each user context)? I have read Some Programs Cannot Access Network Locations When UAC Is Enabled but I do not think it particularly applies. I have seen this answer, but it still does not address non-persistent drives How can I tell what network drives users have mapped?

  Read the article

• Encrypt LAN and wifi traffic on small private network

  - by Grimlockz

  I need some advice about encrypt all traffic on a small private network running wi-fi and LAN traffic on 192.168.0.x network. The network would comprise of client laptops connecting to the wi-fi router (192.168.0.254) via ethernet connection or wireless. The main purpose of the server is for the client laptops to talk to two servers on different IP's (192.168.0.200 and 192.168.0.201) on ports 80 and 433. My main concern is having packet sniffers and what not getting access to the data. The only ways I see at the moment is to have VPN running on the network or use IPSec policy's to do this. Any other ways guys?

  Read the article

• WiFi: Connect to a network with hidden SSID in Windows 7

  - by Dor

  I have Windows 7 with the following station: D-Link DWA-160 Xtreme N Dual Band USB Adapter(rev.A2) (driver version 3.5.0.21). I'm trying to connect to a wireless network that has an hidden SSID with the command: Netsh wlan connect name="myNetworkProfile" The profile is configured to connect even if the network is not broadcasting its name (SSID). Despite that, the command fails promptly every time with the message: The network specified by profile "myNetworkProfile" is not available to connect. Nonetheless, when trying to connect manually using the dialog box (see image below), it successfully connects to the network after about 10 or 15 seconds. Also, Please - no need to elaborate about how useless the hidden SSID feature is.

  Read the article

• Private IP getting routed over Internet

  - by WernerCD

  We are setting up an internal program, on an internal server that uses the private 172.30.x.x subnet... when we ping the address 172.30.138.2, it routes across the internet: C:\>tracert 172.30.138.2 Tracing route to 172.30.138.2 over a maximum of 30 hops 1 6 ms 1 ms 1 ms xxxx.xxxxxxxxxxxxxxx.org [192.168.28.1] 2 * * * Request timed out. 3 12 ms 13 ms 9 ms xxxxxxxxxxx.xxxxxx.xx.xxx.xxxxxxx.net [68.85.xx.xx] 4 15 ms 11 ms 55 ms te-7-3-ar01.salisbury.md.bad.comcast.net [68.87.xx.xx] 5 13 ms 14 ms 18 ms xe-11-0-3-0-ar04.capitolhghts.md.bad.comcast.net [68.85.xx.xx] 6 19 ms 18 ms 14 ms te-1-0-0-4-cr01.denver.co.ibone.comcast.net [68.86.xx.xx] 7 28 ms 30 ms 30 ms pos-4-12-0-0-cr01.atlanta.ga.ibone.comcast.net [68.86.xx.xx] 8 30 ms 43 ms 30 ms 68.86.xx.xx 9 30 ms 29 ms 31 ms 172.30.138.2 Trace complete. This has a number of us confused. If we had a VPN setup, it wouldn't show up as being routed across the internet. If it hit an internet server, Private IP's (such as 192.168) shouldn't get routed. What would let a private IP address get routed across servers? would the fact that it's all comcast mean that they have their routers setup wrong?

  Read the article

• How to troubleshoot intermittent and irregular connection errors on home network (preferrably Mac client)

  - by Martin

  Hi, I'm experiencing intermittent connection errors in our home network from two different computers, normally "Connection Reset" when browsing, but also other issues such as very slow throughput. I have approximately a network setup as below: ISP-Cable Modem-Dlink DIR 655 Router-(Ethernet)-Fon Router-Mac/Windows laptop Basically, is there a simple way to monitor the network and detect where issues are coming from? Right now we don't know if it is the Fon router, the Dlink router, the modem or the ISP. As the issue is intermittent, is there a software that regularly traceroutes a set of destinations and tests e.g. throughput, something that can help us figure out where in the chain the errors are introduced? The more automatic network monitor, the better.

  Read the article

• "Network Error - 53" while trying to mount NFS share in Windows Server 2008 client

  - by Mike B

  CentOS | Windows 2008 I've got a CentOS 5.5 server running nfsd. On the Windows side, I'm running Windows Server 2008 R2 Enterprise. I have the "Files Services" server role enabled and both Client for NFS and Server for NFS are on. I'm able to successfully connect/mount to the CentOS NFS share from other linux systems but am experiencing errors connecting to it from Windows. When I try to connect, I get the following: C:\Users\fooadmin>mount -o anon 10.10.10.10:/share/ z: Network Error - 53 Type 'NET HELPMSG 53' for more information. (IP and share name have been changed to protect the innocent :-) ) Additional information: I've verified low-level network connectivity between the Windows client and the NFS server with telnet (to the NFS on TCP/2049) so I know the port is open. I've further confirmed that inbound and outbound firewall ports are present and enabled. I came across a Microsoft tech note that suggested changing the "Provider Order" so "NFS Network" is above other items like Microsoft Windows Network. I changed this and restarted the NFS client - no luck. I've confirmed that the share folder on the NFS server is readable/writable by all (777) I've tried other variations of the mount command like: mount 10.10.10.10:/share/ z: and mount 10.10.10.10:/share z: and mount -o anon mtype=hard \\10.10.10.10:/share * No luck. As per the command output, I tried typing NET HELPMSG 53 but that doesn't tell me much. Just "The network path was not found". I'm lost on how to proceed with troubleshooting. Any ideas?

  Read the article

• Vyatta internet connection + hosted site on same IP

  - by boburob

  Having a small issue setting up a vyatta. The company internet and two different websites are both on the same IP. Server 1 - Has websites hosted on ports 1000 and 3000 and also has a proxy server installed to provide internet connection to the domain Server 2 - Has a website hosted on ports 80 and 433 The vyatta is correctly natting the appropriate traffic to each server, and allowing the proxy to get internet traffic, however I have a problem getting to the websites hosted on these two servers inside the domain. I believe the problem is that the HTTP request is being sent with an IP, eg: 12.34.56.78. The request will reach the website and the server will attempt to send the request back to the IP, however this is the IP of the Vyatta, so it has nowhere else to go. I thought the solution would be something like this: rule 50 { destination { address 12.34.56.78 port 1000 } inbound-interface eth1 inside-address { address 10.19.2.3 } protocol tcp type destination } But this doesnt seem to do it! UPDATE I changed the rules to the following: rule 50 { destination { address 12.34.56.78 port 443 } outbound-interface eth1 protocol tcp source { address 10.19.2.3 } type masquerade } rule 51 { destination { address 12.34.56.78 port 443 } inbound-interface eth1 inside-address { address 10.19.2.2 } protocol tcp type destination } I am now seeing traffic going between the two with Wireshark, but the website will still fail to load.

  Read the article

< Previous Page | 122 123 124 125 126 127 128 129 130 131 132 133  | Next Page >