Search Results

Search found 4390 results on 176 pages for 'git daemon'.

Page 132/176 | < Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >

• How to clear the REPLACEBATT state from APC UPS after hot-swapping the battery

  - by Hubert Kario

  I replaced a battery in APC SmartUPS by hot-swapping. While the swap was all right and didn't disturb connected computers, the "Battery failed" LED on the front face kept glowing. I tried to use apctest from apcups package. Turned off the daemon and run self test (first changing BATTDATE in EEPROM). The test run fine but didn't clear the REPLACEBATT status or the glowing LED. How to clear the failed battery state without powering the UPS and connected equipment down?

  Read the article

• Will NTP work in an isolated network ( in absence of a reliable time source)

  - by Anand

  Hi, I am investigatiing a typical NTP problem. The setup is as follows :- FreeBSD is being compiled and run on Opensolaris. The config file on OpenSolaris has entry of linux and another opensolaris machine as server and these server machines are syncing time with themselves (local clock) only. The server machines in this case have NTP running on them as well. Within a few minutes of starting the ntp daemon ,client starts syncing time with itself only and remains in that situation after that.All servers are discarded and no time syncing is done with them. My question is , is there any fundamental problem with this setup. Will the NTP work in such isloated network that has no direct or indirect connection with reliable internet time source ?

  Read the article

• Cisco 2911 - problem with DHCP

  - by bluszcz

  Hi, i am configuring DHCP daemon on Cisco 2911. At some point i assigned address 192.168.50.50 to one box (using MAC address 'relation'). When I wanted to saved config - I got warning, that address 192.168.50.50 is already in Pool, which sounds bit weird - it was first host which I started configuring. I tried with following commands: clear ip dhcp server statistics clear ip dhcp conflict but first one doesn't output anything (and show statistics shows that there are 2 addresses in pool), and second one throws "there is no conflicted ips" message. How I can force/purge/clear/allow to bind 192.168.50.50 to this box?

  Read the article

• Timeout ssh sessions after inactivity?

  - by Insyte

  PCI requirement 8.5.15 states: "If a session has been idle for more than 15 minutes, require the user to re-enter the password to re-activate the terminal." The first, and most obvious, way to deal with ssh sessions that are idling at the bash prompt is by enforcing a read-only, global $TMOUT of 900. Unfortunately, that only covers sessions sitting at the bash prompt. The spirit of the PCI spec would also require killing sessions running top/vim/etc. I've considered writing a */1 cron job that parses the output of "/usr/bin/w" and kills the associated shell, but that seems like a blunt instrument. Any ideas for something that would actually do what the spec requires and just lock the terminal? I've looked at away and vlock; they both seem great for voluntarily locking your terminal, but I need a cron/daemon task that will enforce locking.

  Read the article

• having trouble setting up ganglia on three machines

  - by Pieter Breed

  I am running ubuntu 11.10 I have one machine with gmetad, gmond and ganglia-webinterface. When I browse the web interface this machine picks up the local gmond output. I then added another machine, running only gmond. I didn't really change anything in the config, only the name of the cluster. This machine's output showed up in the web view. The I tried to add a third machine, similarly to the second, but it's not showing up in the web view. I tried looking at syslog and running as a daemon, but I'm not seeing anything suspicious there. Any tips for trouble shooting this?

  Read the article

• Nagios and rrd on a old server

  - by Pier

  I have an old server (P4 based) on which nagios (and all the other tools to monitor) is running. In the last few weeks we are seeing a strange behavior. In the /var/spool/pnp4nagios (where temporary files are stored before getting processed by pnp4nagios daemon) we have many files like perfdata.1274949941-PID-18839 and we get an error in npcd.log: [05-27-2010 11:17:46] NPCD: ThreadCounter 0/15 File is perfdata.1274951306-PID-27849 [05-27-2010 11:17:46] NPCD: File 'perfdata.1274951306-PID-27849' is an already in process PNP file. Leaving it untouched. Sometimes some graph are not drawn. The server is pretty loaded (around 5-6 normally) and i suspect that npcd goes in timeout and leave those files behind. What could I do (apart from change the server)? Few infos about the system: centos 5.5 nagios 3.2.1 pnp4nagios 0.6 (from sources) Thanks

  Read the article

• One way sync with either Dropbox or Google drive on linux and windows

  - by sup

  I could not google this one. I would like to use Dropbox or Google drive only as backup, so I would like to ensure I only upload to those services and never download (unless done manually via the web interface). There would be several of us uploading stuff to one account, so we would need to ensure we don't accidentaly delete something on another guy's machine by doing some changes on our local machine. Is there a simple way to do this automatically - i.e. by running a daemon that will upload eveyuthing in a given folder but never download anything? I am on linux, so that complicates things a bit, but I am also interested in windows solutions.

  Read the article

• How do I get rid of sockets in FIN_WAIT1 state?

  - by Gert M

  I have a port that is blocked by a process I needed to kill. (a little telnet daemon that crashed) The process was killed successfully but the port is still in a 'FIN_WAIT1' state. It doesn't come out of it, the timeout for that seems to be set to 'a decade'. The only way I've found to free the port is to reboot the entire machine, which is ofcourse something I do not want to do. $ netstat -tulnap | grep FIN_WAIT1 tcp 0 13937 10.0.0.153:4000 10.0.2.46:2572 FIN_WAIT1 - Does anyone know how I can get this port unblocked without rebooting?

  Read the article

• vsftpd chroot_local_user does nothing

  - by Reinderien

  Hello all. I'm setting up a vsftpd server on: Linux 2.6.32-26-server #48-Ubuntu SMP Wed Nov 24 10:28:32 UTC 2010 x86_64 GNU/Linux When I set chroot_local_user=YES, there is no effect (I can still see / when I log in). There is nothing in syslog or /var/log/vsftpd.log to indicate what's wrong. I know that I'm editing the right conf file and that other settings do come into effect when I restart the daemon, because these work: ssl_enable=YES force_local_data_ssl=YES force_local_logins_ssl=YES Any idea what's wrong? Thanks.

  Read the article

• 'Singleton' application - or let the user only launch one instance of a program at the time

  - by Disco

  I'm running a few linux desktops; mainly for kids (yeah, trying to teach them the right OS at early stage) (running Ubuntu 10.10, Gnome) The problem is that they found very funny to make their workstations (actually, old 512 Mb pentium 4) by launching thousands of firefox instances. I'm looking for a way to restrict them to launch 'N' instances of a particular application. Haven't figured yet how. Thought of a monitoring daemon but I think that would be too ressources hungry. Any idea of a script/trick to achieve this ? Note: i might have 1-2 level of users (the kids, and the more grown up kids) so i have also to limit per user; something like user1: 3firefox, user2: 2firefox instances.

  Read the article

• Running MySQL as SYSTEM Service in Windows XP

  - by enesviem

  I have this strange problem where I create a database in MySQL and I need to restart mysqld but I can't seem to do it with info the MySQL docs. Then, I kill it from the Task Manager and I can't restart it. When I look at the process, it is run by the SYSTEM, rather than me. When I run mysqld it starts the process by me, not the SYSTEM. Am I shutting it down incorrectly? IS there a way to start this daemon as the SYSTEM?

  Read the article

• Any way to make service do not autostart in Ubuntu/Debian, but leave K00 scripts in place?

  - by Evgenyt

  I need to have only stop scripts in rcN.d (runlevels 0,1,6) for apache2. So that I always start it by myself, but when reboot occurs server will shut down apache2 properly. And when I change runlevel 2-3 server doesnt' touch apache daemon (leaving it in the state it is). Basically, I just need a legal way to remove apache2 startup symlinks from rc2.d - rc5.d. With tools like update-rc.d. I can just remove those symlinks by hands, but I'm not sure if this is a proper way for this.

  Read the article

• Table 'mysql.host' doesn't exist

  - by eriktm

  100913 10:21:29 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql /usr/local/mysql/libexec/mysqld: Table 'mysql.plugin' doesn't exist 100913 10:21:29 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 100913 10:21:29 [ERROR] Fatal error: Can't open and lock privilege tables: Table 'mysql.host' doesn't exist 100913 10:21:29 mysqld_safe mysqld from pid file /var/run/mysqld/mysqld.pid ended This is the output from the log-file for mysqld I get when I try to start mysqld with the mysqld_safe command. I tried to run mysql_upgrade to correct the first error, but this command seems to require the server to be started, which is my original problem. Next, it says that the table mysql.host does not exist. I was unable to figure out what this is caused by.

  Read the article

• Send Gmail emails from Facebook address

  - by Mikulas Dite

  Is it somehow possible to link Facebook address each username is given to Gmail? Obviously, there is the "Accounts, Send mail as" feature, but that used to return an error ... Final-Recipient: rfc822; [email protected] Action: failed Diagnostic-Code: smtp; 550 5.1.1 RCP-P2 http://postmaster.facebook.com/response_codes?ip=209.85.210.181#rcp Refused due to recipient preferences You have requested to add [email protected] to your Gmail account. Confirmation code: XXXXXXXX ... The XXX part is actually how the email actually reads, the daemon does in fact obfuscate the code prior to sending it back. I tried again recently, but Facebook mailer does not even return the error message nowadays (alas, it doesn't show in the message center either). So, is there a way to link those to services nowadays?

  Read the article

• Server installation logging / logbook / diary?

  - by The MYYN

  Are there some ways field-tested ways to keep a kind of logbook for a server? Including: software installations (and de-installations) custom configurations (e.g. of a webserver, ssh daemon, etc.) personal notes The big picture. I am preparing a server and would like to extensively document the state and how it was established over time, so that a new person can easily see, what's going on and why. The setup is not too complicated, but I would like to do it anyway. I once used something like Maintain /etc with mercurial on Debian and it was nice, but I am looking for a little more flexible solution. Addendum: So I am interested in logging and documentation first. In an ideal world however, I would like to have a command, which in a few steps would take me from a bare newly installed unix system to a functional environment with all the components setup and in place by the means of, say an 'executable' log. But that would be very ideal, I imagine.

  Read the article

• How to repair Windows XP Installation HDD from another PC?

  - by Matt

  My friend gave me his HDD that has Windows XP Pro installed on it to try and fix it. I don't have the XP CD to repair it, but I do have the ISO. I suppose I could always burn it.. but that's a lot of trouble because I don't have any blank CD's. I plugged it into my PC's hot-swap drive bay, and I have Daemon tools. Is there anyway I can try to repair the XP installation on this HDD from my PC without booting from it and burning my ISO?

  Read the article

• Where to set java heap options (e.g. -Xmx) for Tomcat 6 under Ubuntu 9.04?

  - by Chris

  I'm running Tomcat using the tomcat6 package from Ubuntu 9.04, which makes a daemon out of Tomcat using jsvc. I'd like to know the proper way to set Java heap options like -Xmx for Tomcat. I'd like to put the configuration wherever is most stylistically correct, and wherever is least likely to be overwritten by Ubuntu package updates. The options I see right now: Hard-code them somewhere in /etc/init.d/tomcat6. Hard-code them somewhere in /usr/share/tomcat6/bin/catalina.sh. Create a line in /usr/share/tomcat6/bin/startup.sh to set CATALINA_OPTS to have the desired flags, and then export CATALINA_OPTS as an environment variable. (This looks like it will get picked up by catalina.sh.) The last option sounds like the best one, and it's advocated (without explanation of why) at http://serverfault.com/questions/121038/increasing-javas-heapspace-in-tomcat-startup-script. But I wanted to get a second opinion. Anyone want to confirm that there isn't a better way?

  Read the article

• Memcached clustered alternative

  - by Johan Kooijman

  I'm looking to replace memcached. We have a LOT of traffic to our central memcached node which I'd like to split. There's only so much trunking networks I can do. My general idea is to install a memcached-type daemon on every webserver and have the daemons replicate set/delete/updates over all the daemons, so that each webserver connects to a socket or on localhost. All data should be available on all nodes. The alternatives: - repcached (max 2 masters) - redis (single master) - couchdb/mongodb/handlersocket - persistent data on disk, I'd like to remove the disk part to gain more performance. Any hints?

  Read the article

• How to limit server to specific IP addresses with mod_authz_host?

  - by BeeDog

  Hi! I am very new to this area, so please bear with me. :) Right now I am running an Apache HTTP server on my setup, a very basic configuration. The website hosted on it is accessible from anywhere, and I want to limit the access to a specific IP address range. I've looked into this and I found that one Apache module called mod_authz_host handles this. http://httpd.apache.org/docs/2.2/mod/mod_authz_host.html The problem is, I haven't managed to find documentation that explains well how to actually do the stuff. How do I actually make sure only a certain range of IP addresses can access my site/server? The machine is running Ubuntu Server 10.10, the web files are stored in /var/www/, the apache2 daemon has its stuff stored in /etc/apache2/ and /usr/lib/apache2/modules/*. Thanks in advance, and sorry if this is a stupid question!

  Read the article

• Snort monitoring of spanning interface

  - by aHunter

  I have configured a Cisco 3500 switch with a port SPAN and have my snort node (fedora 13) plugged into it. I am running snort as a daemon and have configured a rule to log all tcp traffic but I am only seeing traffic with a destination of the snort node. I know that the SPAN port is working and wanted to know if there is a specific option that I needed to start snort with in order for it to pickup all the traffic? Or is there something that I have missed here? Many thanks.

  Read the article

• choose server backend to some URL with haproxy

  - by shingara

  To some URL I don't want use some server. So use other. Actually I have this haproxy configuration. global daemon log 127.0.0.1 local0 #log loghost local0 info maxconn 4096 #debug #quiet user haproxy group haproxy defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 balance roundrobin stats enable stats refresh 5s stats auth admin:123abc789xyz # Set up application listeners here. listen application 0.0.0.0:10000 server localhost 127.0.0.1:10100 weight 1 maxconn 5 check server externe 127.0.0.1:10101 weight 1 maxconn 5 check By example I want all url to /users be served only by server localhost, not by externe.

  Read the article

• Is it necessary to change the default users and groups in VMware esxi 4.0 in order to have a secure

  - by Teevus

  By default esxi creates a number of users and groups including: daemon nfsnobody root nobody vimuser dcui How secure is this default security setup? Besides changing the root password, is it advisable to modify the default users and groups? E.g. does esxi use default passwords for the accounts or anything else that could be exploited by malicious users? My scenario is very basic and I don't require any custom users or groups as only sysadmins will ever need to administer the virtual infrastructure, and they can do so using the root account. Thanks

  Read the article

• Improving sound quality with remote ESD server

  - by cuu508

  Hi, I'm investigating low-budget ways to get audio from my PC (Ubuntu) to HiFi without wires. I'm currently testing a setup where Asus WL-500gP wireless router runs ESD daemon and has attached USB soundcard which is then plugged into HiFi. I'm testing playback on PC with mpg123-esd and Spotify under Wine. The sound is there, latency is unexpectedly low, but I also hear occassional clicks and some distortion from time to time. I suppose that's because of the low latency and wireless streaming of uncompressed audio--any packet drops, CPU temporarily being busy etc. will cause clicks in sound output. Is there a way around this problem, increasing latency / buffer size somehow perhaps? Streaming using shoutcast protocol seems to be a way out but I have feeling that would be a complex and brittle setup.

  Read the article

• Automatic Server Management

  - by Radoslav

  I try to find any kind of automatic management services. What I mean: I purchase dedicated server. Login SSH and install any kind of Daemon. Control security, tune LAMP stack, monitoring etc. from dashboard. Never touch SSH and login in to the server. Pay every month for this service. I already find few providers, but they support only EC2 cloud servers. If you can suggest me anything for dedicated machines? If not- I need to hire anyone for 5h Administrator and 715h "Box-Watcher" every month :|

  Read the article

• Man pages in Linux

  - by Ayos

  I don't seem to have all the man pages that I need. For example, my college computers (running Fedora 14) have man pages for ASCII, all the standard C libraries (stdlib.h, stdio.h) and so on and so forth. I wish to "install" these pages, after looking up on the Internet I couldn't really find anything that made sense. How can I get, say, the man-page of ASCII (I know it's not really a command or a daemon or anything like that, but typing man ASCII on the college computer gets me a page with the ASCII value table + a little more information). I don't want to keep using the Internet for looking up man pages every time I need to look up a function, function prototype or the ASCII table or something like that.

  Read the article

< Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >