Search Results

Search found 47491 results on 1900 pages for 'super x man'.

Page 132/1900 | < Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >

  • Windows installer constantly asking for Word CD

    - by Dennis
    My daughter uses Word and at some point in the past tried to install a feature which needed the install CD. She no longer has the CD, figured she could live without the feature and cancelled the install. However, every time she boots the computer it tries to resume the install and asks for the CD. All you have to do is hit cancel but it seems a bit annoying to me to have to do that each time you boot. How can I get it to permanently abort the install?

    Read the article

  • svchost consuming more than 50% CPU all the time in windows 7

    - by claws
    Hello, I'm using windows 7 ultimate. svchost containing DCOM Server Process Launcher Plug and Play Power services is consuming more than 50% of CPU for most of the time. I found this blog post: http://blog.hansmelis.be/2007/06/17/windows-vista-long-delay-when-switching-songs-in-media-player/ That process is associated with two services: DCOM Server Process Launcher and Plug and Play. For the Vulcans among us, all logic stops there for a second. What do those two services have to do with WMP? The answer is provided by Vista's new audio engine. The new engine supports several audio "enhancements". But for the enhancements to work, the engine needs to determine if your hardware is up to the task. And when does it check that? Each time a sound output device is accessed. That's pretty nice if you can do a hot swap of sound hardware, but I don't see me doing that anytime soon. Anyways, it does provide us with the link to the correct service because checking hardware is done by the "Plug and Play" service. One might think that deactivating each enhancement would solve the problem, but that's wishful thinking. The configuration of the enhancements is located in the properties of the sound hardware. When opening the tab, I found out that no enhancements were active. Hmmm... so why does it check the hardware? Well, it does that in case you actually enable an enhancement. To completely stop the hardware checking, you have to tick the box labelled Disable all enhancements. As soon as you do that, Vista finally understands you don't want to use them buts thats for vista. Is it the same case with windows 7 too? and I couldn't find any "Disable all enhancements" in my controlpanelsounds (mmsys.cpl). Where can I find this option in windows 7? How to solve this?

    Read the article

  • How to use a DVI/HDMI monitor with Mac Mini's DisplayPort?

    - by dr dork
    If I buy a Mac Mini, how can I use it with my Dell monitor? The Dell does not have a DisplayPort, only DVI and HDMI. I was looking at the Mac Minis and noticed they don't have DVI or VGA ports. Does the Mac Mini come with any kind of an adapter that will allow me to use my existing Dell monitor? Thanks in advance for your help, I'm going to start researching this question right now.

    Read the article

  • Windows 7: Touch gestures in IE not working without explorer.exe being run once

    - by Michael
    Details: Internet Explorer 9 and Windows 7 Professional, running on a HP TouchSmart (touch screen PC). It is going to be a kiosk PC (running a custom GUI for displaying websites). Scenario 1: When running Internet Explorer as a normal program in Windows 7, touch functions work perfectly. I can scroll the website by dragging it with my finger, I can pinch zoom and I can touch-and-hold right click. I now change the default shell in Windows to Internet Explorer (ie. IE starts instead of explorer.exe). Internet Explorer of course starts up when logging in. However, touch functions are reduced to basic clicking (no dragging, no pinch zooming, no touch-and-hold right click). Then I manually start explorer.exe, and the touch functions work again! And here is the weird part: When I kill explorer.exe, the touch functions keeps working - even if I close IE and start a new instance. Scenario 2: The exact same, but instead of changing the default shell to Internet Explorer, I change it to my own program, which uses an embedded Internet Explorer ("WebBrowser"). Same thing happens. What I've tried: Autorun programs: When explorer.exe launches, it launches all the autorun programs. There are no relevant programs being run by explorer, but just in case, I have manually started all the autorun programs, so that it is identical (but without explorer.exe) to a normal login. It still does not work (until I launch explorer.exe). Specifically TabTip.exe, TabTip32.exe and wisptis.exe are all running. All services are also started. To sum it up Running explorer.exe once changes something in the touch capabilities of Internet Explorer. It doesn't matter if explorer.exe is running - as long as it has been run once. Does anyone know what causes this behavior? Or how I can circumvent it neatly? Thanks!

    Read the article

  • Automount in Ubuntu 9.10

    - by easyrider
    Hi, By default Ubuntu doesn't mount internal NTFS hard drives automatically. A fstab solution not working properly, because of conflicts with the "intelligent" mount system. If I add my hd in fstab and reboot - it will be mounted. But if I go to nautilus, open places panel and click eject button (unmount) and than click on hd again to mount it, I will get an error. In 9.04 to solve this problem you need to modify hal rules in /etc/hal/... preferences.fdi in my case I modified it for only one drive. <device> - <match key="storage.hotpluggable" bool="false"> - <match key="storage.removable" bool="false"> <merge key="storage.automount_enabled_hint" type="bool">false</merge> - <match key="storage.model" string="ST3250310NS"> <merge key="storage.automount_enabled_hint" type="bool">true</merge> </match> </match> </match> </device> But this is not working in 9.10 - devs removed this function from hal to devkit-disk or udev? I don't know. Could you please tell me where automount rules are stored in 9.10? And how to create new rules, and what program controls automount in 9.10?

    Read the article

  • Remove ads from Windows Live Messenger

    - by Mehper C. Palavuzlar
    How can I remove the ads from Windows Live Messenger build 14.0.8089.726? Maybe there is a registry setting for that? Googling this brings lots of results with some applications full of viruses and malware. Please suggest something that you have tried yourself (on Windows 7) and confirmed as successful.

    Read the article

  • How do I make dashboard widgets active on logon?

    - by CharlesB
    There are a few dashboard widget that are useful even when not going in Dashboard. For example, SVN Notifier sends a Growl notification when commits are made to a repository you want to watch. Or, Delivery Status does the same for status update on tracked packages. The thing is when I log into OS X, those status updates won't happen until the first time I actually enter into Dashboard, so it looks like they are not initialized at startup. How to fix this?

    Read the article

  • How do I determine if my controller is in IDE or AHCI mode in Linux?

    - by philcolbourn
    I have an old MacBook Pro 4,1 (early 2008) - but I suspect an answer would apply to many MacBook Pros. It has an Intel IDE/SATA controller (ICH8M/ICH8M-E). I have installed a patched MBR that is supposed to put my controller into AHCI mode. It does this by setting some controller port value that I don't understand. This seems to work as I get this from lspci: 00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 03) 00:1f.2 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 03) Now most, perhaps all, sites that provide a solution (enabling AHCI) suggest that after a sleep/wake cycle that a controller will revert to IDE mode due to how Apple support Windows. They recommend disabling sleep. From author of patchedcode.bin I think Enabling AHCI for Windows on MacBooks NB: I do not have bootcamp installed and I do not have Windows installed. Is there a way to prove that my controller is in IDE or AHCI mode? Background Data Using patchedcode.bin MBR I get this in syslog: Jun 12 22:33:22 max kernel: [ 1.860955] ahci 0000:00:1f.2: version 3.0 Jun 12 22:33:22 max kernel: [ 1.861052] ahci 0000:00:1f.2: irq 45 for MSI/MSI-X Jun 12 22:33:22 max kernel: [ 1.861117] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 1.5 Gbps 0x1 impl SATA mode Jun 12 22:33:22 max kernel: [ 1.861120] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems Jun 12 22:33:22 max kernel: [ 1.861130] ahci 0000:00:1f.2: setting latency timer to 64 Jun 12 22:33:22 max kernel: [ 1.880880] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) Jun 12 22:33:22 max kernel: [ 1.880983] scsi2 : ahci Jun 12 22:33:22 max kernel: [ 1.884552] scsi3 : ahci Jun 12 22:33:22 max kernel: [ 1.886932] scsi4 : ahci Jun 12 22:33:22 max kernel: [ 1.886998] ata3: SATA max UDMA/133 abar m2048@0xdb504000 port 0xdb504100 irq 45 Jun 12 22:33:22 max kernel: [ 1.887000] ata4: DUMMY Jun 12 22:33:22 max kernel: [ 1.887002] ata5: DUMMY Jun 12 22:33:22 max kernel: [ 2.204103] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Jun 12 22:33:22 max kernel: [ 2.204656] ata3.00: ATA-8: FUJITSU MHY2200BH, 0081000D, max UDMA/100 Jun 12 22:33:22 max kernel: [ 2.204662] ata3.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32), AA Jun 12 22:33:22 max kernel: [ 2.205324] ata3.00: configured for UDMA/100 Jun 12 22:33:22 max kernel: [ 2.205554] scsi 2:0:0:0: Direct-Access ATA FUJITSU MHY2200B 0081 PQ: 0 ANSI: 5 Using my original MBR I get this from syslog: Jun 13 18:07:13 max kernel: [ 0.622861] ata_piix 0000:00:1f.1: version 2.13 Jun 13 18:07:13 max kernel: [ 0.622869] ata_piix 0000:00:1f.1: power state changed by ACPI to D0 Jun 13 18:07:13 max kernel: [ 0.622924] ata_piix 0000:00:1f.1: setting latency timer to 64 Jun 13 18:07:13 max kernel: [ 0.623339] scsi0 : ata_piix Jun 13 18:07:13 max kernel: [ 0.623730] scsi1 : ata_piix Jun 13 18:07:13 max kernel: [ 0.623765] ata1: PATA max UDMA/100 cmd 0x8108 ctl 0x811c bmdma 0x80e0 irq 21 Jun 13 18:07:13 max kernel: [ 0.623767] ata2: PATA max UDMA/100 cmd 0x8100 ctl 0x8118 bmdma 0x80e8 irq 21 Jun 13 18:07:13 max kernel: [ 0.623810] ata_piix 0000:00:1f.2: MAP [ Jun 13 18:07:13 max kernel: [ 0.623811] P0 -- -- -- ] Jun 13 18:07:13 max kernel: [ 0.623866] ata_piix 0000:00:1f.2: setting latency timer to 64 Jun 13 18:07:13 max kernel: [ 0.624241] scsi2 : ata_piix Jun 13 18:07:13 max kernel: [ 0.624558] scsi3 : ata_piix Jun 13 18:07:13 max kernel: [ 0.624862] ata3: SATA max UDMA/133 cmd 0x80f8 ctl 0x8114 bmdma 0x8020 irq 18 Jun 13 18:07:13 max kernel: [ 0.624865] ata4: SATA max UDMA/133 cmd 0x80f0 ctl 0x8110 bmdma 0x8028 irq 18 Jun 13 18:07:13 max kernel: [ 1.208879] ata3.00: ATA-8: FUJITSU MHY2200BH, 0081000D, max UDMA/100 Jun 13 18:07:13 max kernel: [ 1.208882] ata3.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 0/32) Jun 13 18:07:13 max kernel: [ 1.208961] ata1.01: ATAPI: MATSHITA DVD+/-RW UJ-867S, 1.00, max UDMA/33 Jun 13 18:07:13 max kernel: [ 1.216186] ata3.00: configured for UDMA/100 Jun 13 18:07:13 max kernel: [ 1.224396] ata1.01: configured for UDMA/33

    Read the article

  • Migrating from DD-WRT to Tomato

    - by Collin Allen
    Is it possible to switch to the latest version of Tomato on a router that's already running DD-WRT? Using the default Linksys firmware on my WRT54GL v1.1, I had to upload a micro version of DD-WRT first. I imagine that, since I'm now running third-party firmware, I won't have to do that again to make the switch, but I thought I should check so as not to brick it. This router is taking a back seat to a new AirPort Extreme (for the 'n' capability), but I still want to have the soon-to-be-Tomato device sit between the AirPort Extreme and my modem for the superior traffic graphing.

    Read the article

  • Setting up Git / Apache on Windows

    - by yodaj007
    I'm following this tutorial to set up a personal Git server on Apache on my Windows 7 box. However, when I add the following to my httpd.conf, Apache throws an error when I try to start it. Can anyone assist in fixing whatever is wrong? SetEnv GIT_PROJECT_ROOT C:/Repositories SetEnv GIT_HTTP_EXPORT_ALL ScriptAliasMatch "(?x)^/(.*/(HEAD | info/refs | objects/(info/[^/]+ | [0-9a-f]{2}/[0-9a-f]{38} | pack/pack-[0-9a-f]{40}.(pack|idx)) | git-(upload|receive)-pack))$" "C:/Program Files (x86)/git/libexec/git-core/git-http-backend.exe/$1" This is a fresh install of Apache. The only other change I've made to the config file is telling Apache to listen on port 9000 (IIS is listening on 80). This is the error from my event logs: The Apache service named reported the following error: ScriptAliasMatch takes two arguments, a regular expression and a filename . I tried putting all of the text on one line, like so: ScriptAliasMatch "(?x)^/(.*/(HEAD | info/refs | objects/(info/[^/]+ | [0-9a-f]{2}/[0-9a-f]{38} | pack/pack-[0-9a-f]{40}.(pack|idx)) | git-(upload|receive)-pack))$" "C:/Program Files (x86)/git/libexec/git-core/git-http-backend.exe/$1" But nada.

    Read the article

  • how to make a multiboot usb key ?

    - by zillion
    I wanna cut my 8 gb usb key into several partitions to use wintoflash for a windows xp (maybe nlited before) and I wanna put also the Framakey ubuntu-fr remix pack into it has the second bootable OS and tweak and mod it a little cause if I can I wanna switch ubuntu 9.04 included to the LTS version ... So someone know how to do it easily ??? IMP : in short I wanna make a dual-boot usb key with windows xp sp3 and ubuntu 8.04.3 LTS ...

    Read the article

  • Why can't I reconnect to my Philips SHB9000 bluetooth headset?

    - by Thomas Eyde
    This is so annoying. When I connected my Philips SHB9000 bluetooth to my Windows 7 (64 bit) for the very first time, it worked well. I had to manually change the default playback device, but otherwise it worked. Then, when I start up my computer from standby, it's nearly random when I can reconnect or not. My last option is to remove the bluetooth device and reconnect it. But now, even that doesn't work. The sad thing is, this used to work better on Windows 7 beta. Windows Update has a new driver which fails to install. Searching for this driver yields nothing. I thought all vendors had an official site for their drivers? Well, Philips seems to have none. If there is no answer to this problem, my advice is to NOT buy this headset. It's good looking, the sound is nice, but what need do we have from that if we can't use the bloody device?

    Read the article

  • Proper application shutdown before windows xp auto shutdown

    - by vashman
    I frequently leave the computer on playing a movie or downloading a file while I go to bed. I do use the 'shutdown computer when finished' feature of KMPlayer or getright or uTorrent or whatever program I am using. This method effectively shuts down the computer, but the problem is that there are some applications that seem to exit forcefully when doing this kind of shutdown, this being clearly reflected in winamp not saving the current playlist and config, messenger not saving the chat logs, etc. My goal here would be to have automatically close properly all applications when the auto/scheduled program triggers it. I am looking for some Windows shutdown mode/setting that does application closing like the user would do. I am not expecting to auto-click on save dialogs prompts, if this is needed I will do it before leaving the computer on for auto shutdown.

    Read the article

  • Sound card / microphone impedance mismatch

    - by axk
    First of all I'm not completely sure this is impedance mismatch, but from what I found on the Internet I believe it is. It seems to be a common problem. The question is not as much about solving the problem as about why it is happening (if I'm right about the cause of the problem, of course). I had this quiet microphone problem with several built in cards and microphones and now with a Creative Audigy SE. There's a microphone boost option which introduces a lot of noise with volume increase, but even this doesn't seem to give loud enough sound in some cases. The mic on my current headphones is very quiet with Audigy SE without the boost but is very loud and low noise with an external Sound Blaster Connect. So the question is have I just been unlucky with my sound cards and microphones or is it a common problem? And if it is a common problem why is it so difficult for the vendors to standardize on the sound card / microphone impedance? Edit: the OS is Windows (XP/7), but I don't believe it is OS-specific.

    Read the article

  • Play music on iPhone through computer

    - by Kyle Cronin
    Now that I've had my iPhone for a few months, I'm trying an experiment to see if I can't replace the laptop I carry around with my iPhone + internet connected computer. To this end, I've been trying to find a program that will let me play the music on my iPhone through the hardware and software on the host computer. If I recall correctly this was possible a few years ago with the iPod - Linux software like Rhythmbox and Banshee was able to read the music off an iPod and play it through the speakers. I even thought I recalled iTunes itself being capable of this at one time. Now, however, iTunes greys out/disables the music on my iPhone and I can't find any documented support for the iPhone in any other music program. Is this really no longer possible? Am I limited to using the headphone jack to get music to play? (note: I am using an iPhone 3G with the 3.0 software. I am attempting to play music on computers other than the one I sync with) Several replies mention that I should check "manually manage" to do this. I just tried this on a computer that I don't sync my iPhone to and it asked me to erase and sync, which is obviously something I don't want to do. update: OK, I checked the "Manually manage music and videos" box on a computer that I didn't sync to (now known as "Computer A"), and it told me that I needed to erase & sync to cause the changes to have effect, so I did. At this point I'm guessing that my iPhone thinks that it's syncing with that computer. I copied over a few songs using the autofill feature. At this point, Computer A sees the maybe 10 or so songs I've copied using autofill. I then plug my iPhone into my Macbook ("Computer B") which I've been syncing with. At this point, I'm pretty sure that it still thought that all my synced content was still on my iPhone. The "manually manage music and videos" checkbox isn't checked, so I check it and go through a similar process where iTunes erases the synced content and I copy over a playlist. At this point, there's no trace of the songs that I copied over from Computer A. So I plug my iPhone into Computer A - in the Music section are the handful of songs that I had copied over earlier, greyed out and unplayable. To make sure that this wasn't some sort of caching issue, I plugged my iPhone into my sister's Macbook ("Computer C") and it lists the same few, greyed out songs that I had copied over from Computer A. Plugging into Computer B doesn't reveal these songs at all, only the songs that it copied over (these are playable). A few things: This inconsistent behavior is driving me insane. Why would my iPhone report two versions of its contents to different computers? Is there a way to get a computer to completely forget about an iPhone and just resync everything to get everything into a consistent state? Even if I get the phone into a consistent state, I still can't play the files on my phone anywhere but the computer I sync with, which was my original goal. What am I doing wrong? maybe I should read the fine print before I mess with my iPhone So going over this thread with a fine-toothed comb again yields this lovely tidbit in the Apple docs: Note: Even when manually managing, some content may only be available from one library at time. This includes all content on iPhone and video content on iPods. OK, so manually managing is a dead end on the iPhone. Are there any other options? Any unofficial third-party programs or drivers that will work?

    Read the article

  • I'm looking for a hebrew font

    - by Moshe
    I'm looking for a (preferably free) hebrew font that the letter ? ("Chet"/"Ches") is shaped like the upper half of the letter "s" and is not a script font. The letter ? (lamed) should be shaped like a printed one, not have a loop on the bottom. Thanks.

    Read the article

  • Canon LiDE 600F FAU on Snow Leopard?

    - by jdmuys
    Hello, I have been able to use my Canon LiDE 600F scanner under Snow Leopard to scan paper sheet, after installing Canon's latest driver software. However, I cannot find a way to make the FAU (Film Adaptor Unit) to work: Canon's software want to calibrate it first and gives an error message "Calibration cannot be performed. Pull out the film. 182.0.0". (of course there is no film). Hamrick's VueScan doesn't seem to support the FAU Apple's Image Capture doesn't propose a film option either Did I miss something? Did somebody manage to scan film (positive or negative) using the LiDE 600F under Snow Leopard? Many thanks

    Read the article

  • Photoshop vector line

    - by Yuval
    When I use the line tool in Photoshop, it creates a vector layer mask with the shape of that line. When I draw a curved line with the pen tool, the only option I see for making a line out of the path is "Stroke path", which is not vector (raster). How do I create a vector line/curve with the pen tool in Photoshop (CS4)? Thanks!

    Read the article

  • What is the difference between safety and security?

    - by Lernkurve
    Question What is the difference between safety and security in the context of information management or computer science? Elaboration This could be the canonical answer for people searching for it. Let me know if superuser.com is the wrong site for this question. I have, of course, googled it and haven't found an answer that seemed short and to the point. Wikipedia wasn't very helpful either: safety, information security.

    Read the article

  • Installing drivers for switchable graphics

    - by Anonymous
    I recently bought a laptop that came with Windows 7 64-bit installed. I have some older (16-bit and 32-bit) software that doesn't work with 64-bit Windows, but works just fine with 32-bit. Since I also wanted to get rid of all of the pre-installed spam, I decided to wipe the hard drive and install a fresh copy of Windows 7 32-bit. I can't get the graphics cards working. This laptop uses switchable graphics, an Intel card and a Radeon card. I first tried installing this driver from Intel, which works for the Intel card. Of course, the Radeon card doesn't work with this driver and I need it for some of the newer games I have. I also tried this driver. Windows's device manager will recognize the Radeon card, but it will still use the Intel card. Also, even though that package says it contains the Intel driver, the Intel card still isn't properly recognized by Windows (leaving me with a nasty 800x600 resolution). On top of that, the Catalyst Control Center won't open (saying "The Catalyst Control Center is not supported by the driver version of your enabled graphics adapter") I tried installing HP's driver then installing Intel's driver on top of it. Device manager will then recognize both graphics cards properly. However, the laptop still uses the Intel card. The CCC still won't start (saying the same thing as before) and I can't find any of 'switching' graphics cards. Before formatting, I could right-click the desktop and click "Configure Switchable Graphics" This option hasn't been in the context menu regardless of what driver(s) I've installed. After some research, I found out that this menu entry runs the command "cli.exe Start PowerXpressHybrid" I've tried manually running this command, but I get the same unsupported message from CCC. So, does anyone know how I can get this working? I would like to be able to switch between the Intel and Radeon. But, if there's some way to disable the Intel and use only the Radeon, that would be fine I dual-boot with Linux (framebuffer uses the Intel, haven't even tried getting X set up yet) Here's the output of lspci # lspci -v | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller]) 01:00.0 VGA compatible controller: ATI Technologies Inc NI Seymour [AMD Radeon HD 6470M] (prog-if 00 [VGA controller]) The laptop is a HP Pavilion g6t-1d00. HP doesn't support installing anything but Windows 7 64-bit, so calling tech support isn't an option. Thanks for any help UPDATE: I finally got it working. After a fresh install of Windows 7, I installed the HP driver (the one linked above). Then, there's an optional Windows update I installed (don't remember the exact name, but it'll stick out). After that, graphics switching works just like it's supposed to. Moab, thanks anyways for your help

    Read the article

  • why does chkdsk always report errors on a bad shutdown

    - by rep_movsd
    Once in a while, Windows XP hangs on my laptop (usually when going into standby or hibernate and occasionally on startup) and I have to forcefully poweroff. Ususally chkdsk never runs automatically (I thought it should know that the partitions have nit been unmounted and do that). I religiously run chkdsk without /F after bad shutdowns like this, and invariably it reports that the drive has unfixed errors and must be checked with /F and I do that, and more often than not, the chdsk that runs on startup does not report fixing anything. I have had times in the past (and not only just on this system) when not running chkdsk leads to some strange errors like files not opening even though they exist and inability to save certain files, so I make it a point to always chkdsk after bad shutdown. I never understood why this is : Isnt the whole point of a journalling filesystem like NTFS to avoid file system corruption and endless chkdsks? I even tried once disabling write caching to see if it made any difference, but to no avail....

    Read the article

  • Finder.app preview pane and QuickLook stretch some of my photos

    - by mcandre
    The Finder column view preview pane and QuickLook stretch many of my photos. But when I open the same photos in Preview.app, they look normal. Screenshot: For example, download this image (reaver.jpg), and view it with Finder's column view. Now view it with QuickLook. It renders correctly in every other application, so there's something going wrong in how QuickLook/Finder get the image dimensions. This problem started happening in either Mac OS X 10.8.1 or 10.8.2. Specs: Finder 10.8 QuickLook v4.0 (555.0) Mac OS X 10.8.2 MacBook Pro 2009 Also posted in Apple Discussions.

    Read the article

  • Permissions restoring from Time Machine - Finder copy vs "cp" copy

    - by Ben Challenor
    Note: this question was starting to sprawl so I rewrote it. I have a folder that I'm trying to restore from a Time Machine backup. Using cp -R works fine, but certain folders cannot be restored with either the Time Machine UI or Finder. Other users have reported similar errors and the cp -R workaround was suggested (e.g. Restoring from Time Machine - Permissions Error). But I wanted to understand: Why cp -R works when the Finder and the Time Machine UI do not. Whether I could prevent the errors by changing file permissions before the backup. There do indeed seem to be some permissions that Finder works with and some that it does not. I've narrowed the errors down to folders with the user ben (that's me) and the group wheel. Here's a simplified reproduction. I have four folders with the owner/group combinations I've seen so far: ben ~/Desktop/test $ ls -lea total 16 drwxr-xr-x 7 ben staff 238 27 Nov 14:31 . drwx------+ 17 ben staff 578 27 Nov 14:29 .. 0: group:everyone deny delete -rw-r--r--@ 1 ben staff 6148 27 Nov 14:31 .DS_Store drwxr-xr-x 3 ben staff 102 27 Nov 14:30 ben-staff drwxr-xr-x 3 ben wheel 102 27 Nov 14:30 ben-wheel drwxr-xr-x 3 root admin 102 27 Nov 14:31 root-admin drwxr-xr-x 3 root wheel 102 27 Nov 14:31 root-wheel Each contains a single file called file with the same owner/group: ben ~/Desktop/test $ cd ben-staff ben ~/Desktop/test/ben-staff $ ls -lea total 0 drwxr-xr-x 3 ben staff 102 27 Nov 14:30 . drwxr-xr-x 7 ben staff 238 27 Nov 14:31 .. -rw-r--r-- 1 ben staff 0 27 Nov 14:30 file In the backup, they look like this: ben /Volumes/Deimos/Backups.backupdb/Ben’s MacBook Air/Latest/Macintosh HD/Users/ben/Desktop/test $ ls -leA total 16 -rw-r--r--@ 1 ben staff 6148 27 Nov 14:34 .DS_Store 0: group:everyone deny write,delete,append,writeattr,writeextattr,chown drwxr-xr-x@ 3 ben staff 102 27 Nov 14:51 ben-staff 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown drwxr-xr-x@ 3 ben wheel 102 27 Nov 14:51 ben-wheel 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown drwxr-xr-x@ 3 root admin 102 27 Nov 14:52 root-admin 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown drwxr-xr-x@ 3 root wheel 102 27 Nov 14:52 root-wheel 0: group:everyone deny add_file,delete,add_subdirectory,delete_child,writeattr,writeextattr,chown Of these, ben-staff can be restored with Finder without errors. root-wheel and root-admin ask for my password and then restore without errors. But ben-wheel does not prompt for my password and gives the error: The operation can’t be completed because you don’t have permission to access “file”. Interestingly, I can restore the file from this folder by dragging it directly to my local drive (instead of dragging its parent folder), but when I do so its permissions are changed to ben/staff. Here are the permissions after the restore for the three folders that worked correctly, and the file from ben-wheel that was changed to ben/staff. ben ~/Desktop/test-restore $ ls -leA total 16 -rw-r--r--@ 1 ben staff 6148 27 Nov 14:46 .DS_Store drwxr-xr-x 3 ben staff 102 27 Nov 14:30 ben-staff -rw-r--r-- 1 ben staff 0 27 Nov 14:30 file drwxr-xr-x 3 root admin 102 27 Nov 14:31 root-admin drwxr-xr-x 3 root wheel 102 27 Nov 14:31 root-wheel Can anyone explain this behaviour? Why do Finder and the Time Machine UI break with the ben / wheel permissions? And why does cp -R work (even without sudo)?

    Read the article

  • Movie Library on Windows Media Center Extender

    - by Shawn Miller
    I have a share setup on a NAS server with ripped versions of my DVDs. I pointed the Windows 7 version of the Windows Media Center Movie Library feature to the network share and it's able to find and play all my movies when running Windows Media Center from the local computer. When I try this on my Xbox 360 extender it never discovers any of my movies. Anyone able to get this to work?

    Read the article

  • sudo equivalent configuration on Solaris 10

    - by daedlus
    I am looking to configure on Solaris 10 to achieve the below: user=jon group=jtu jon is owner of /opt/app user=ken group=jtu ken is owner of /data On Linux I have added the below line %jtu ALL= NOPASSWD: /bin/*, /usr/bin/* so that jon is able to access /data/tmp and delete files. This doesn't work on solaris10 since there is no sudo by default. How do I configure Solaris 10 so jon can delete files in /data/tmp? Thanks

    Read the article

< Previous Page | 128 129 130 131 132 133 134 135 136 137 138 139  | Next Page >