Search Results

Search found 25182 results on 1008 pages for 'ask'.

Page 133/1008 | < Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >

• Lexmark X5650 doesn't print (scanning works)

  - by unor

  I want to use a Lexmark X5650 under Ubuntu. When I connect it via USB, Ubuntu recognizes the device, but can't find a driver. On the Lexmark support site, you can select "Unix/Linux" and then "Ubuntu 9.04", "9.10", "10.04" and "10.10". However, all versions lead to the same driver: lexmark-08z-series-driver-1.0-1.i386.deb.sh.tar.gz (Last updated: 2012-04-13). While installing this driver, the installer asks me to connect the device. As soon as I connect it via USB, Ubuntu now adds the printer automatically. So after the installation completed, I had 2 printers set up. But I can't print anything (I tried it with both printer configurations). Scanning works fine, though. So I guess the driver installation and the device connection are successful. When I try to print something, the print job is listed in the printing queue, but nothing happens. After some time, I get an error message which starts a debug wizard, but in the end it reads something like "Sorry, couldn't find the reason". I had several different error messages (unfortunately, I didn't record them), one was approximately like "printer cannot communicate with computer". Another said that my color ink was low (which is true, but black is full). Another said there was an input/output error. I tried it with Ubuntu 11.10. Because I read that some people had success with 10.04., I installed it in QEMU and installed the driver there, too. Same problem, though. I'd like to upgrade to 12.04, if it should work there for any reason, but I read that for some people this printer stopped working in 12.04 :/ So, it would be best if the printer would work in 12.04. If that's not possible, I'd be fine with starting a QEMU virtual machine with any GNU/Linux distribution that works with my printer.

  Read the article

• Xubuntu dual monitor broke display

  - by Arman yaraee

  After I used Settings Display to enable my second monitor, my first display is not working anymore either. So I enabled both, then clicked save configuration since it was working and boom it crashed. Now when I start up, I can see the screen which I type my password but it goes black after that! When I boot into recovery mode it works fine but in Settings Display I don't see HDMI at all to disable it. Is there anyway to restore all display setting to default? (I can Ctrl+ALT+F1 and type commands but xrandr returns no results over there) EDIT I should clarify that system bios is set to laptop display

  Read the article

• How to create a PPA for C++ program?

  - by piotr

  My questions are: c++/gtkmm project created with NetBeans. How to make package to PPA from this? I have created target files structure (*.desktop, iconfile, ui glade files). Binary goes to /opt/extras.ubuntu.com/myagenda/bin/myagenda. There is also a folder of glade files, that must go to /opt/extras.ubuntu.com/myagenda/bin/myagenda/ui. Desktop file goes to /usr/share/applications/myagenda.desktop. Icon goes to /usr/share/icons/hicolor/scalable/apps/myagenda.svg As you see, there is really small amount of files. Now, how to manage all this stuff, to create package on PPA, which knows where and how put this files to their targets? +-- opt ¦   +-- extras.ubuntu.com ¦   +-- myagenda ¦   +-- bin ¦   ¦   +-- myagenda ¦   +-- ui ¦   +-- item_btn_delete.png ¦   +-- item_btn_edit.png ¦   +-- myagenda.png ¦   +-- myagenda.svg ¦   +-- reminder.png ¦   +-- ui.glade +-- usr +-- share +-- applications ¦   +-- myagenda.desktop +-- icons +-- hicolor +-- scalable +-- apps +-- myagenda.svg Update: Created install file in debian directory with targets: data/myagenda /opt/extras.ubuntu/com/myagenda/bin data/ui/* /opt/extras.ubuntu/com/myagenda/ui data/myagenda.desktop /usr/share/applications data/myagenda.svg /usr/share/icons/hicolor/scalable/apps After dpkg-buildpackage it builds, but for amd64 architecture. Now, trying to change that to i386.

  Read the article

• DELL Inspiron 9400 SD Card Reader not working on 10.11 ubuntu

  - by Mario Martz

  Im new in linux, just installed Ubuntu 11.10 in a Dell Inspiron 9400, everything works fine with the exception of the SD card reader, everytime I insert a card the computer doesnt do anything, its like the SD card reader is not there. I did a $lspci and it shows the next drivers 03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) Everytime I insert a memory card, dmesg shows the next d status 0x600b00 [ 2687.227351] end_request: I/O error, dev mmcblk0, sector 64 [ 2687.229436] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.229440] end_request: I/O error, dev mmcblk0, sector 65 [ 2687.230512] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.230515] end_request: I/O error, dev mmcblk0, sector 66 [ 2687.231588] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.231592] end_request: I/O error, dev mmcblk0, sector 67 [ 2687.232674] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.232678] end_request: I/O error, dev mmcblk0, sector 68 [ 2687.234763] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.234766] end_request: I/O error, dev mmcblk0, sector 69 [ 2687.236864] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.236868] end_request: I/O error, dev mmcblk0, sector 70 [ 2687.238942] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.238946] end_request: I/O error, dev mmcblk0, sector 71 [ 2687.238949] Buffer I/O error on device mmcblk0, logical block 8 [ 2687.241028] mmcblk0: retrying using single block read [ 2687.243104] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.243108] end_request: I/O error, dev mmcblk0, sector 64 [ 2687.245212] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.245215] end_request: I/O error, dev mmcblk0, sector 65 [ 2687.247298] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.247302] end_request: I/O error, dev mmcblk0, sector 66 [ 2687.248389] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.248393] end_request: I/O error, dev mmcblk0, sector 67 [ 2687.250476] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.250480] end_request: I/O error, dev mmcblk0, sector 68 [ 2687.252617] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 [ 2687.252621] end_request: I/O error, dev mmcblk0, sector 69 [ 2687.254737] mmcblk0: error -110 sending read/write command, response 0x0, card status 0x600b00 and more of the same but with different sector number Im using Kernel 3.0.0-12-generic By the way, when I was installing it and ubuntu asks about installation (If I want to install it along with windows or delete something or change the partitions of the HDD) if I go to the window to change the partition of the disc, linux detects the SD Card (if there's one inserted course). Any help with this it would be appreciated -sorry for my english Thank you

  Read the article

• Tips for debugging Samba performance?

  - by j-g-faustus

  Samba gives me 24 MB/s read and 44 MB/s write, while ftp gives 97 and 112 MB/s under the same circumstances. The documentation says that Generally, you should find that Samba performs similarly to ftp at raw transfer speed. In my case it clearly doesn't. Where can I find tips on how to debug Samba performance? Or alternatively tips for replacing Samba with something else? (I can't use ftp, unfortunately, as I need something that can be used with rsync/rsnapshot.) More details: Both computers are running Ubuntu 10.10 (using Samba because I have a Mac as well) The Samba share is on a local home network, mounted as $ mount ... //server.local/share/ on /mnt/share type cifs (rw,mand) Samba performance was tested by copying (cp) a single file of ~4GB to and from the share, using time for timing and calculating transfer speed by hand. ftp performance are the numbers from the ftp client for get/put of the same file. iperf gives network speed ~900 Mbits/s bonnie++ gives disk speeds 200 MB/s on both sides for block reads as well as block writes Tried changing the parameters suggested in the performance tuning HOWTO (read/write raw, read size, socket options), most of them made little to no difference. (The one that made a difference caused write speed to drop 50%.)

  Read the article

• sensors reporting weird temperatures

  - by Felix

  lm-sensors is reporting weird temps for me: $ sensors coretemp-isa-0000 Adapter: ISA adapter Core 0: +38.0°C (high = +72.0°C, crit = +100.0°C) coretemp-isa-0001 Adapter: ISA adapter Core 1: +35.0°C (high = +72.0°C, crit = +100.0°C) coretemp-isa-0002 Adapter: ISA adapter Core 2: +32.0°C (high = +72.0°C, crit = +100.0°C) coretemp-isa-0003 Adapter: ISA adapter Core 3: +42.0°C (high = +72.0°C, crit = +100.0°C) w83627dhg-isa-0290 Adapter: ISA adapter Vcore: +1.10 V (min = +0.00 V, max = +1.74 V) in1: +1.62 V (min = +0.06 V, max = +0.17 V) ALARM AVCC: +3.34 V (min = +2.98 V, max = +3.63 V) VCC: +3.34 V (min = +2.98 V, max = +3.63 V) in4: +1.83 V (min = +1.30 V, max = +1.15 V) ALARM in5: +1.26 V (min = +0.83 V, max = +1.03 V) ALARM in6: +0.11 V (min = +1.22 V, max = +0.56 V) ALARM 3VSB: +3.30 V (min = +2.98 V, max = +3.63 V) Vbat: +3.18 V (min = +2.70 V, max = +3.30 V) fan1: 0 RPM (min = 0 RPM, div = 128) ALARM fan2: 1117 RPM (min = 860 RPM, div = 8) fan3: 0 RPM (min = 10546 RPM, div = 128) ALARM fan4: 0 RPM (min = 10546 RPM, div = 128) ALARM fan5: 0 RPM (min = 10546 RPM, div = 128) ALARM temp1: +88.0°C (high = +20.0°C, hyst = +4.0°C) ALARM sensor = diode temp2: +25.0°C (high = +80.0°C, hyst = +75.0°C) sensor = diode temp3: +121.5°C (high = +80.0°C, hyst = +75.0°C) ALARM sensor = thermistor cpu0_vid: +2.050 V Please note temp3. How can I know what temp3 is, and why it is so high? The system is really stable (which I guess it wouldn't be at those temps). Also, note the really decent core temps, which suggest a healthy system as well. My guess is that the readout is wrong. On another computer it reported temperatures below 0 degrees centigrade, which was not possible, considering the environment temperature of ~22-24. Is this some known bug/issue? Should I try some Windows programs (like CPU-Z) and see they give similar results?

  Read the article

• Can't specify window's class in CCSM's Place Windows

  - by Anto

  Following this method, I wanted to "place" some of my windows on specific viewports. For instance, I want Xchat to always start on my top right viewport (x=2, y=1). But after I have set everything up and clicked the "Close" button to validate it (I don't have any other action button, like "OK" or "Apply"), the only thing that get saved up are the viewport X and Y coordinates. The window class (in my case class=Xchat) remains empty. This bug only occurs in the "Windows with fixed viewport" section; it works well in the "Windows with fixed placement mode", for instance. How can I solve or circumvent this issue ?

  Read the article

• LibreOffice Icons are blurry

  - by Ryan McClure

  My LibreOffice icons for the individual apps are fine, they look great in both the launcher and the switcher. Yet, if I open the apps from the main LibreOffice program or if I open the document that I want to edit (And it opens its own "icon" as it always does), the icon is incredibly blurry. Here's what it looks like: On the launcher, I put the actual Calc and Impress launchers and on their left is the icons opened from a document. I know they aren't "blurry" as much as they are smaller. What should I do to remedy this? They are the same in the switcher (I can't find a way to take a screenshot of the switcher) Edit: I changed my Unity plugin from Rotated to standard, and the problem is still there; so, it isn't a Rotated bug.

  Read the article

• How do I make the F-keys work in byobu on 12.04, for midnight commander (mc), htop, etc?

  - by Jorge Castro

  I use byobu with the tmux backend on my 12.04 server. I'd like to use the midnight commander shortcut keys with it, but the F keys don't work. I've seen some posts on the issues here: https://bugs.launchpad.net/byobu/+bug/386363 https://answers.launchpad.net/byobu/+question/127610 but they are out of date and don't seem to work for newer versions of byobu. How can I either work around this or use MC in a way that works better?

  Read the article

• Setting environment variables when executing Eclipse via Unity launcher icon

  - by Nullptr

  My question is a followup for the following: How to pin Eclipse to the Unity launcher? I created Eclipse's icon to the Unity launcher based on the selected answer at the above link. However, when I launch Eclipse via this icon, the environment variables are not properly set. I need to call . /opt/intel/bin/compilervars.sh intel64 to use Intel compiler tools in Eclipse. However, launching via the icon can't do it. Of course, running manually Eclipse on the terminal is okay. I tried to place . /opt/intel/bin/compilervars.sh intel64 on several places such as /etc/profile and /etc/bash.bashrc. But, still not working. Where is the best and correct place to call such environment setup?

  Read the article

• Why is my Internet connection randomly dropping?

  - by Jeanno

  Ever since I have installed 12.04 (clean install not an upgrade), i have been having a drop in the Internet connection. The drop in the connection can be anything from 15 seconds to about 3 mins, and then the connection comes back. This behaviour happens while I am actively browsing the Internet, or if I wake up the computer and open Firefox (sometimes I have connection and sometimes I don't) . Please note that when the internet connection is on, it is not slow (as speedtest.net results show) In the beginning, I thought it was a problem with the driver r8169 for my RTL8111/8168B Ethernet card, so I downloaded the r8168 from Realtek website, followed the detailed instructions (blacklisted r8169, changed the file to '.bsh' ...), but still the same problem persisted. So I switched to a wireless connection, and I got the same problem with internet connection dropping randomly. Any ideas? Thanks in advance Output from 'lspci -v' Code: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: f8000000-fa0fffff Prefetchable memory behind bridge: 00000000d0000000-00000000dbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:01.1 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: f4000000-f60fffff Prefetchable memory behind bridge: 00000000c0000000-00000000cbffffff Capabilities: [88] Subsystem: Dell Device 04a7 Capabilities: [80] Power Management version 3 Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [a0] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Capabilities: [140] Root Complex Link Kernel driver in use: pcieport Kernel modules: shpchp 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at f6108000 (64-bit, non-prefetchable) [size=16] Capabilities: [50] Power Management version 3 Capabilities: [8c] MSI: Enable+ Count=1/1 Maskable- 64bit+ Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at f6107000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 53 Memory at f6100000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Capabilities: [130] Root Complex Link Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Memory behind bridge: fa400000-fa4fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 0000c000-0000cfff Prefetchable memory behind bridge: 00000000dc100000-00000000dc1fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fa300000-fa3fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fa200000-fa2fffff Capabilities: [40] Express Root Port (Slot+), MSI 00 Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Capabilities: [90] Subsystem: Dell Device 04a7 Capabilities: [a0] Power Management version 2 Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) (prog-if 20 [EHCI]) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at f6106000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port: BAR=1 offset=00a0 Capabilities: [98] PCI Advanced Features Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation P67 Express Chipset Family LPC Controller (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel modules: iTCO_wdt 00:1f.2 RAID bus controller: Intel Corporation 82801 SATA Controller [RAID mode] (rev 05) Subsystem: Dell Device 04a7 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 42 I/O ports at f070 [size=8] I/O ports at f060 [size=4] I/O ports at f050 [size=8] I/O ports at f040 [size=4] I/O ports at f020 [size=32] Memory at f6105000 (32-bit, non-prefetchable) [size=2K] Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit- Capabilities: [70] Power Management version 3 Capabilities: [a8] SATA HBA v1.0 Capabilities: [b0] PCI Advanced Features Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) Subsystem: Dell Device 04a7 Flags: medium devsel, IRQ 5 Memory at f6104000 (64-bit, non-prefetchable) [size=256] I/O ports at f000 [size=32] Kernel modules: i2c-i801 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at f8000000 (32-bit, non-prefetchable) [size=16M] Memory at d0000000 (64-bit, prefetchable) [size=128M] Memory at d8000000 (64-bit, prefetchable) [size=32M] I/O ports at e000 [size=128] Expansion ROM at fa000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 01:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at fa080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 02:00.0 VGA compatible controller: NVIDIA Corporation Device 0dc5 (rev a1) (prog-if 00 [VGA controller]) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f4000000 (32-bit, non-prefetchable) [size=32M] Memory at c0000000 (64-bit, prefetchable) [size=128M] Memory at c8000000 (64-bit, prefetchable) [size=64M] I/O ports at d000 [size=128] Expansion ROM at f6000000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100] Virtual Channel Capabilities: [128] Power Budgeting <?> Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau Kernel modules: nouveau, nvidiafb 02:00.1 Audio device: NVIDIA Corporation GF106 High Definition Audio Controller (rev a1) Subsystem: NVIDIA Corporation Device 085b Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at f6080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 03:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 03) (prog-if 30 [XHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 16 Memory at fa400000 (64-bit, non-prefetchable) [size=8K] Capabilities: [50] Power Management version 3 Capabilities: [70] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [90] MSI-X: Enable+ Count=8 Masked- Capabilities: [a0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [140] Device Serial Number ff-ff-ff-ff-ff-ff-ff-ff Capabilities: [150] Latency Tolerance Reporting Kernel driver in use: xhci_hcd 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 51 I/O ports at c000 [size=256] Memory at dc104000 (64-bit, prefetchable) [size=4K] Memory at dc100000 (64-bit, prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Endpoint, MSI 01 Capabilities: [b0] MSI-X: Enable- Count=4 Masked- Capabilities: [d0] Vital Product Data Capabilities: [100] Advanced Error Reporting Capabilities: [140] Virtual Channel Capabilities: [160] Device Serial Number 03-00-00-00-68-4c-e0-00 Kernel driver in use: r8168 Kernel modules: r8168 05:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller (rev 01) (prog-if 10 [OHCI]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at fa300000 (64-bit, non-prefetchable) [size=2K] I/O ports at b000 [size=256] Capabilities: [50] Power Management version 3 Capabilities: [80] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [98] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [130] Device Serial Number 00-10-dc-ff-ff-cf-56-1a Kernel driver in use: firewire_ohci Kernel modules: firewire-ohci 06:00.0 SATA controller: JMicron Technology Corp. JMB362 SATA Controller (rev 10) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Device 04a7 Flags: bus master, fast devsel, latency 0, IRQ 19 I/O ports at a040 [size=8] I/O ports at a030 [size=4] I/O ports at a020 [size=8] I/O ports at a010 [size=4] I/O ports at a000 [size=16] Memory at fa210000 (32-bit, non-prefetchable) [size=512] Capabilities: [8c] Power Management version 3 Capabilities: [50] Express Legacy Endpoint, MSI 00 Kernel driver in use: ahci Note that my wireless card is not showing, I have the Ralink 3390 card (which apparently does not show up on Ubuntu for some reason), however I am able to connect to wireless network and connect to the internet (when it is working)

  Read the article

• Remote reboot over ssh does not restart

  - by Finn Årup Nielsen

  I would like to remotely reboot my Ubuntu 12.04 LTS server via ssh. I do sudo reboot and I loose connection and the server connection does not reappear. It does not ping. When I go the the physical computer with a screen attached I see a black screen and hear that the server is still on. I do a hard power off (press power on button for a few seconds) and the server halts. After I press power on the server boots with no problem. As far as I remember the remote reboot has previously worked on that server. I wonder if sudo reboot & will help? I suppose I could also try sudo shutdown -r and see if that does any difference. I have listed an excerpt of /etc/log/syslog below. The last thing it records is the stopping of the logging. Oct 24 10:14:49 servername kernel: [1354427.594709] init: cron main process (1060) killed by TERM signal Oct 24 10:14:49 servername kernel: [1354427.594908] init: irqbalance main process (1080) killed by TERM signal Oct 24 10:14:49 servername kernel: [1354427.595299] init: tty1 main process (1424) killed by TERM signal Oct 24 10:14:49 servername kernel: [1354427.637747] init: plymouth-upstart-bridge main process (20873) terminated with status 1 Oct 24 10:14:49 servername kernel: Kernel logging (proc) stopped. Oct 24 10:14:49 servername rsyslogd: [origin software="rsyslogd" swVersion="5.8.6" x-pid="876" x-info="http://www.rsyslog.com"] exiting on signal 15. Oct 24 10:25:34 servername kernel: imklog 5.8.6, log source = /proc/kmsg started. Oct 24 10:25:34 servername rsyslogd: [origin software="rsyslogd" swVersion="5.8.6" x-pid="862" x-info="http://www.rsyslog.com"] start

  Read the article

• Error in Using Gparted to add Unallocated space

  - by Ba7a7chy

  I'm trying to Add Unallocated space to my Ubuntu partition which is inside an extended partition. i get this error: GParted 0.12.1 --enable-libparted-dmraid Libparted 2.3 Move /dev/sda3 to the left and grow it from 93.31 GiB to 219.75 GiB 00:00:00 ( ERROR ) calibrate /dev/sda3 00:00:00 ( SUCCESS ) path: /dev/sda3 start: 292,704,254 end: 488,394,751 size: 195,690,498 (93.31 GiB) move partition to the left and grow it from 93.31 GiB to 219.75 GiB 00:00:00 ( ERROR ) old start: 292,704,254 old end: 488,394,751 old size: 195,690,498 (93.31 GiB) requested start: 27,545,600 requested end: 488,392,703 requested size: 460,847,104 (219.75 GiB) libparted messages ( INFO ) Unable to satisfy all constraints on the partition. Can't have overlapping partitions. ========================================

  Read the article

• Linux DD command partition -to- partition

  - by Ben Jackson

  I just used the DD command to copy the contents of one partition over to another partition on another drive, like this: dd if=/dev/sda2 of=/dev/sdb2 bs=4096 conv=noerror sda2 partition was 66GB and sdb2 was 250GB. I read that by doing this the extra space on the drive I am copying to will be wasted, is this true? I wasn't worried about loosing the extra space for the time being however, I just ran: sudo kill -USR1 (PID) to view the current status of DD and it has written over 66GB of data, will it continue to write data until it gets to 250GB? If so, is there a way to stop the process without corrupting it as waiting for it to write blank space seems like a waste of time.

  Read the article

• Rhythmbox goes crazy if I change keyboard layout

  - by krokoziabla

  Not so trivial to explain but I'll try. Launch Rhythmbox Insert a CD in the CD-ROM The CD is not automatically identified (it's of a not very famous Russian band) I'm manually setting track names and... Magic, black magic! If I change the keyboard layout (RU <- EN) during editing then Rhythmbox kicks me out of the editing. So if a track name contains both Russian and English words I'm compelled to write one part, press Enter (so that the changes are not lost), change layout, click on the track name, write another part in the opposite layout. In some tricky names I have to do this several times. By the way, I use Alt+Shift to change layout. Any ideas?

  Read the article

• Fan starts at startup (Macbook Pro 6,2)

  - by kalaracey

  I recently installed ubuntu 10.10 onto my Macbook Pro 6,2 unibody. I've got everything setup (not my first time), except on startup the fan goes crazy. I choose linux from rEFIt, and after GRUB the fan turns up to what I think is the highest speed. The computer definitely is not overheating. It doesn't do this when booting Mac OS X. Macbook Pro 6,2 Unibody (15") Ubuntu 10.10 kernel 2.6.35-28 generic Mactel PPA (pommed, etc.)

  Read the article

• Black screen in installation when Nvidia graphic card plugged

  - by jopasso1

  When I try to install any recent version of Ubuntu, the screen shows some green and purple mess (like analog TVs when thers no signal). Then, a black screen. I guess it keeps booting in live/install mode. But I can't see it. I tried installing from CD and USB, I tryed changing some BIOS settings... I installed older versions, like 8.04, and it worked, but after updating the system, it crashes again. That's why I discovered that upgrading Nvidia drivers, made system show a black screen again. After that, I unplugged the Nvidia card and installed 12.04 with onboard card. It worked perfectly. Then, I plugged Nvidia again and system booted, but only showing that black screen again. I keep working with onboard card, so far... The nVidia is a GeForce 8500GT.

  Read the article

• Wifi hotspot to connect to Android using non-AP supported cards

  - by 3l4ng

  I'm running Ubuntu 13.10 64b on a Dell Inspiron N5010. My wireless device (found using lspci) is Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01). I bought a new android phone and want to connect to Internet by using the laptop as a Wireless Access Point (ad-hoc doesn't work with Android). I tried following tutorials like the one at How to setup a wi-fi hotspot (access point mode)?. The relevant output from iw list was Supported interface modes: * IBSS * managed Running sudo hostapd /path/to/conf/file gave me (eth1 is the wireless, verified by iwconfig) Failed to create interface mon.eth1: -95 (Operation not supported) Could not set channel for kernel driver eth1: Unable to setup interface. Could not connect to kernel driver. I am able to use Connectify and Virtualrouter on Windows, and the phone works great. How do I get an access point running on Ubuntu? I'm open to other alternatives as well.

  Read the article

• NVIDIA x server - "sudo nvidia config" does not generate a working 'xorg.config'

  - by Mike

  I am over 18 hours deep on this challenge. I got to this point and am stuck. very stuck. Maybe you can figure it out? Ubuntu Version 12.04 LTS with all the updates installed. Problem: The default settings in "etc/X11/xorg.conf" that are generated by the "nvidia-xconfig" tool, do not allow the NVIDIA x server to connect to the driver in my "System Settings Additional Driver window". (that's how I understand it. Lots of information below). Symptoms of Problem "System Settings Additional Driver" window has drivers, but the nvidia x server cannot connect/utilize any of the 4 drivers. the drivers are activated, but not in use. When I go to "System Tools Administration NVIDIA x server settings" I get an error that basically tells me to create a default file to initialize the NVIDIA X server (screen shot below). This is the messages the terminal gives after running a "sudo nvidia-xconfig" command for the first time. It seems that the generated file by the tool i just ran is generating a bad/unusable file: If I run the "sudo nvidia-xconfig" command again, I wont get an error the second time. However when I reboot, the default file that is generated (etc/X11/xorg.conf) simply puts the screen resolution at 800 x 600 (or something big like that). When I try to go to NVIDIA x server settings I am greeted with the same screen as the screen shot as in symptom 2 (no option to change the resolution). If I try to go to "system settings display" there are no other resolutions to choose from. At this point I must delete the newly minted "xorg.conf" and reinstate the original in its place. Here are the contents of the "xorg.conf" that is generated first (the one missing required information): # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 304.88 (buildmeister@swio-display-x86-rhel47-06) Wed Mar 27 15:32:58 PDT 2013 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Hardware: I ran the "lspci|grep VGA". There results are: 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [Quadro 1000M] (rev a1) More Hardware info: Ram: 16GB CPU: Intel Core i7-2720QM @2.2GHz * 8 Other: 64 bit. This is a triple boot computer and not a VM. Attempts With Not Success on My End: 1) Tried to append the "xorg.conf" with what I perceive is missing information and obviously it didn't fly. 2) All the other stuff I tried got me to this point. 3) See if this link is helpful to you (I barely get it, but i get enough knowing that a smarter person might find this useful): http://manpages.ubuntu.com/manpages/lucid/man1/nvidia-xconfig.1.html 4) I am completely new to Linux (40 hours over past week), but not to programming. However I am very serious about changing over to Linux. When you respond (I hope someone responds...) please respond in a way that a person new to Linux can understand. 5) By the way, the reason I am in this mess is because I MUST have a second monitor running from my laptop, and "System Settings Display" doesn't recognize my second display. I know it is possible to make the second display work in my system, because when I boot from the install CD, I perform work on the native laptop monitor, but the second monitor shows a purple screen with Ubuntu in the middle, so I know the VGA port is sending a signal out. If this is too much for you to tackle please suggest an alternative method to get a second display. I don't want to go to windows but I cannot have a single display. I am really fudged here. I hope some smart person can help. Thanks in advance. Mike. **********************EDIT #1********************** More Details About Graphics Card I was asked "which brand of nvidia-card do you have exactly?" Here is what I did to provide more info (maybe relevant, maybe not, but here is everything): 1) Took my Lenovo W520 right apart to see if there is an identifier on the actual card. However I realized that if I get deep enough to take a look, the laptop "won't like it". so I put it back together. Figuring out the card this way is not an option for me right now. 2) (My computer is triple boot) I logged into Win7 and ran 'dxdiag' command. here is the screen shot: 3) I tried to look on the lenovo website for more details... but no luck. I took a look at my receipts and here is info form receipt: System Unit: W520 NVIDIA Quadro 1000M 2GB 4) In win7 I went to the NVIDIA website and used the option to have my card 'scanned' by a Java applet to determine the latest update for my card. I tried the same with Ubuntu but I can't get the applet to run. Here is the recommended driver from from the NVIDIA Applet for my card for Win7 (I hope this shines some light on the specifics of the card): Quadro/NVS/Tesla/GRID Desktop Driver Release R319 Version: 320.00 WHQL Release Date: 3.5.2013 5) Also I went on the NVIDIA driver search and looked through every possible combination of product type + product series + product to find all the combinations that yield a 1000M card. My card is: Product Type: Quadro Product Series: Quadro Series (Notebooks) Product: 1000M ***********************EDIT #2******************* Additional Symptoms Another question that generated more symptoms I previously didn't mention was: "After generating xorg.conf by nvidia-xconfig, go to additional drivers, do you see nvidia-304?" 1) I took a screen shot of the "additional drivers" right after generating xorg.conf by nvidia-xconfig. Here it is: 2) Then I did a reboot. Now Ubuntu is 600 x 800 resolution. When I logged in after the computer came up I got an error (which I always get after generating xorg.conf by nvidia-xconfig and rebooting) 3) To finally answer the question - No. There is no "NVIDIA-304" driver. Screen shot of additional drivers after generating xorg.conf by nvidia-xconfig and rebooting : At this point I revert to the original xorg.conf and delete the xorg.conf generated by Nvidia.

  Read the article

• question about 12.10 32 bit syslinux 4.06 EDD 2012-10-23 usb direct boot

  - by logan

  alright so guys i am trying to do a direct boot for Ubuntu 12.10 (as stated in the topic) i have been trying to do a direct boot for about ten minutes now. so i have to do a direct boot because my original OS has a corrupted kernel (i am trying to fix a friends laptop) Toshiba satellite C655D-S5518 anyway getting back to the main point when i put the usb in everything starts up fine it loads the usb then it goes to this screen saying "SYSLINUX 4.06 EDD 2012-10-23 Copyright (C) 1994-2012 H. Peter Anvin et al." also getting a blinking line (as if i could put something in however when i try to type it does not show up so im guessing its telling me it is loading) However i am not getting a corrupted file or any kind of file error so im guessing my main question is, is this normal? and if so how long does it take for this to be done and what are the steps proceeding this? sorry guys if this is a dumb question i am new to the Ubuntu party haha thanks Logan.

  Read the article

• Screen lock broken when using separate x screens

  - by Wolf

  For some reason, the screen lock appears to be broken when I use separate x screens (it works fine if I use twin view or just one monitor, though). If I wait for the screen to lock (or if I tell it to lock), it fades to black, showing only the mouse cursor. However, when I move the mouse to bring up the password prompt, nothing happens, the screens remain completely blank. Furthermore, it would appear that the screen lock never activated in the first place, for two reasons: one, if I blindly enter my password and press enter, nothing happens; and two, if I press ctrl+alt+delete and then enter it logs me out (which shouldn't happen if the password prompt is there, right), losing any progress I have on any of the open programs (meaning, not a very friendly option for a programmer ;) ). So yeah, does anyone know why this is happening, and how to fix it? Thanks! Notes: I am using Ubuntu 11.10 64 bit. I am using gnome-classic, but the same problem occurs when I use unity. I do not have xscreensaver, nor do I have any screen savers running (except, I guess for the default blank one).

  Read the article

• Can't add to panel nor delete panel

  - by david

  Hello everybody! I cannot add any applet to any (top or bottom) panel, cannot delete any panel nor create a new panel. When I right-click on the panel the only options available are: Properties, Help or About panels. [I cannot post an image because of spam prevention, so I'll do my best] I can see when I right-click (bold means clickable): Add to panel Properties Delete this panel New panel Help About Panels Trying to solve this I did what is usually suggested: gconftool-2 –-recursive-unset /apps/panel # might be optional rm -rf ~/.gconf/apps/panel pkill gnome-panel but I only got a nice empty panel (no Applications Places System, no clock, no shutdown button...) to which I couldn't add any applet, so I decided to take the default profiles in .gconf and .gconfd from a live CD and overwrite mines. Now we are back to the beginning. I also have tried to lock completely the panel (with both gconf-editor and pessulus) and later unlock it completely but it didn't work. Here is the system information: $ lsb_release Distributor ID: Ubuntu Description: Ubuntu 10.04.2 LTS Release: 10.04 Codename: lucid Thank you very much.

  Read the article

• How do I configure networking when using XEN on 12.04 Server

  - by Ingram

  I'm following this guide, https://help.ubuntu.com/community/XenProposed, and I'd like to setup a static IP address, but I don't know how. I'm using 12.04 Server. This is the step I'm having trouble at (I'm using eth1): Edit /etc/network/interfaces, and make it look like this: auto lo iface lo inet loopback auto xenbr0 iface xenbr0 inet dhcp bridge_ports eth0 auto eth0 iface eth0 inet manual I do this, and here is my output from ifconfig: eth1 Link encap:Ethernet HWaddr 00:17:a4:f8:79:20 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:478264 errors:0 dropped:0 overruns:0 frame:0 TX packets:2895 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:46470058 (46.4 MB) TX bytes:214620 (214.6 KB) Interrupt:17 Memory:fa000000-fa012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) xenbr0 Link encap:Ethernet HWaddr 00:17:a4:f8:79:20 inet addr:192.168.1.122 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::217:a4ff:fef8:7920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:471842 errors:0 dropped:0 overruns:0 frame:0 TX packets:2795 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:37005780 (37.0 MB) TX bytes:182010 (182.0 KB) So how do I give this system a static IP address? Sorry, I'm not that familiar with networking on Ubuntu.

  Read the article

• Wine 1.2 crash after I start Mega 5.0

  - by Tomáš Šíma

  I installed Mega 5.0 by running "sudo sh MEGA5_Setup_deb_v2.sh" The application downloaded wine 1.2 as mega requires in order to work under Ubuntu. However every time I start the application through the icon provided, wine crashes asking me to send/save bug report, the problem is that if I choose to do so, megas starting window pops up covering the bug report window leaving me unable to do anything (as it won't move) The only solution I have come up with is to log out and log back in, as I cancels wine. I beg you following: Please post detailed step by step instructions how to deal with said problem Tell me if forceful log out, can damage computer of any of my data Please forgive me my weak English as it is not my native language. Also forgive me my weak skills concerning Ubuntu usage as I have me forced to switch to Ubuntu this very day. Thank you.

  Read the article

• composite-video-to-usb adaptor

  - by sawa

  I bought a composite-video-to-usb adaptor. I want to stream video game in ubuntu. How can I do that? My environment: Monoprice USB Video and Audio Grabber Ubuntu 11.04 The relevant output of lsusb: Bus 001 Device 011: ID 0572:262a Conexant Systems (Rockwell), Inc. The relevant output of sudo lshw: *-usb:0 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #4 vendor: Intel Corporation physical id: 1a bus info: pci@0000:00:1a.0 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:16 ioport:f0e0(size=32) *-usb:1 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #5 vendor: Intel Corporation physical id: 1a.1 bus info: pci@0000:00:1a.1 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:21 ioport:f0c0(size=32) *-usb:2 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #6 vendor: Intel Corporation physical id: 1a.2 bus info: pci@0000:00:1a.2 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:f0a0(size=32) *-usb:3 description: USB Controller product: 82801JI (ICH10 Family) USB2 EHCI Controller #2 vendor: Intel Corporation physical id: 1a.7 bus info: pci@0000:00:1a.7 version: 00 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:18 memory:e0525c00-e0525fff *-multimedia description: Audio device product: 82801JI (ICH10 Family) HD Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=HDA Intel latency=0 resources: irq:43 memory:e0520000-e0523fff *-usb:4 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #1 vendor: Intel Corporation physical id: 1d bus info: pci@0000:00:1d.0 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:23 ioport:f080(size=32) *-usb:5 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #2 vendor: Intel Corporation physical id: 1d.1 bus info: pci@0000:00:1d.1 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:19 ioport:f060(size=32) *-usb:6 description: USB Controller product: 82801JI (ICH10 Family) USB UHCI Controller #3 vendor: Intel Corporation physical id: 1d.2 bus info: pci@0000:00:1d.2 version: 00 width: 32 bits clock: 33MHz capabilities: uhci bus_master cap_list configuration: driver=uhci_hcd latency=0 resources: irq:18 ioport:f040(size=32) *-usb:7 description: USB Controller product: 82801JI (ICH10 Family) USB2 EHCI Controller #1 vendor: Intel Corporation physical id: 1d.7 bus info: pci@0000:00:1d.7 version: 00 width: 32 bits clock: 33MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=0 resources: irq:23 memory:e0525800-e0525bff The relevant output of dmesg: [18953.220035] usb 1-1: new high speed USB device using ehci_hcd and address 6 [19964.761076] Linux video capture interface: v2.00 [19964.767112] usbcore: registered new interface driver uvcvideo [19964.767115] USB Video Class driver (v1.0.0)

  Read the article

< Previous Page | 129 130 131 132 133 134 135 136 137 138 139 140  | Next Page >