Search Results

Search found 25894 results on 1036 pages for 'ask the readers'.

Page 135/1036 | < Previous Page | 131 132 133 134 135 136 137 138 139 140 141 142  | Next Page >

• Wireless icon shows grey box

  - by donald

  Hello I am running kubuntu 13.10. I had to install using the server disk and did a upgrade to the desktop version to enable full disk encryption using multiple drives. For some weird reason when I move my mouse over to the wireless icon which has an red circle and a line through it, up pops a grey box with nothing in it. This stops me from chosing which ssid's I can connect to. Ubuntu has the drive for my wirless card and it is working verified using #lspci | grep Network Centrino Wireless-N 2230 I am connected to my network from the install wizard but I need to be able to choose which networks. Please help.

  Read the article

• Wifi range issues and intermittent dropouts, Thinkpad Edge

  - by jimbo

  If I am more than a couple of metres from my access point (and I'm seeing this across various APs) with my newish Thinkpad Edge 15, running 10.10, the wifi performance becomes ... flaky. When this is happening, I see the following in dmesg, although I'm not sure if it's related: [ 2497.011099] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2502.012711] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2507.009254] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2512.008367] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2517.007467] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2522.006558] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2527.008157] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2532.007251] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2537.003838] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2542.005427] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2547.004496] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded [ 2552.003611] intel ips 0000:00:1f.6: CPU power or thermal limit exceeded lspci -vvv has the following to say about my wireless adapter: 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 Subsystem: Intel Corporation Centrino Wireless-N 1000 BGN Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 49 Region 0: Memory at f0500000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlagn Kernel modules: iwlagn If I get within a couple of metres of the access point, I still see that output in dmesg, but the connection stabilises. My question is threefold: how do I get better wifi range, what can/should I do about those messages in dmesg, and most crucially, are the two related? As ever let me know if there's other information that would help! Edit: I am using this machine in exactly the same locations I used my previous Thinkpad (T61) running various older versions of Ubuntu, so I definitely feel there is something wrong, rather me having unreasonable expectations of range!

  Read the article

• How can I get add-apt-repository to work?

  - by Kristopher Arens

  Whenever I try to add a repository via the command line, I get the following error message: Traceback (most recent call last): File "/usr/bin/add-apt-repository", line 125, in ppa_info = get_ppa_info_from_lp(user, ppa_name) File "/usr/lib/python2.7/dist-packages/softwareproperties/ppa.py", line 80, in get_ppa_info_from_lp curl.perform() pycurl.error: (60, 'server certificate verification failed. CAfile: /etc/ssl/certs/ca-certificates.crt CRLfile: none') Is there a way to remedy this situation?

  Read the article

• Alt-Tab in Unity 2D makes app icon jiggle instead of switching

  - by itsadok

  I'm using Unity 2D as my desktop, and it works fine most of the time, but every now and then, I try to Alt-Tab to switch to a different application, and instead of switching to that window, the launcher bar opens, and the icon of the application I was trying to switch to starts jiggling. If I try to switch to something else, that icon starts jiggling too. If I click on the icon with the mouse, then it stops jiggling and switches to the requested window. What is this behavior? I haven't seen any mention of jiggling icons in Unity. I don't understand the original purpose of this, and I'd like a way to fix it so that I won't have to use the mouse.

  Read the article

• Hide 'Your profile could not be opened correctly'

  - by B. Roland

  Hello! I have a small public internet cafe, with Ubuntu 10.04 and 10.10. I'm using Google Chrome 7.0.517.44 (64615), with AutoScroll - Version: 2.7.5; AdBlock is removed because of high CPU loads, and unconfortable speed of machine. "Your profile could not be opened correctly" error is displayed: This image is only an illustration. The reason is that I changed permissions of some config files, to don't remember the history, there are no setting in options, to don't use history. I've been removed write permission to: ~/.config/google-chrome$ find . -group nopasswdlogin ./Default/Archived History ./Default/History ./Default/Visited Links When I solved all of my problem, I'll remove some other write permission, this is a public place. What methods are known to HIDE this message? Thanks!

  Read the article

• How can I change my cursor behavior?

  - by Doug Clement

  When I am typing, my mouse cursor, if left on the text, will eventually auto-click in whatever space in the the text box I happen to be, causing me to type in the middle of a sentence. Also, the cursor in the text box will frequently stop mid-word and the screen will scroll down all of a sudden when pressing the space bar while typing. My question is, how do I change this behavior because it is driving me absolutely bat crap crazy. I have an Acer Aspire One D257 Netbook. I am not sure if it's a Xubuntu problem because it does this while I am using Windows 7 too. Any help would be nice, thanks!

  Read the article

• Cannot FTP without simultaneous SSH connection?

  - by Lucas

  I'm trying to set up an old box as a backup server (running 10.04.4 LTS). I intend to use 3rd party software on my PC to periodically connect to my server via FTP(S) and to mirror certain files. For some reason, all FTP connection attempts fail UNLESS I'm simultaneously connected via SSH. For example, if I use putty to test the connection to port 21, the system hangs and times out. I get: 220 Connected to LeServer USER lucas 331 Please specify the password. PASS [password] <cursor> However, when I'm simultaneously logged in (in another session) everything works: 220 Connected to LeServer USER lucas 331 Please specify the password. PASS [password] 230 Login successful. Basically, this means that my software will never be able to connect on its own, as intended. I know that the correct port is open because it works (sometimes) and nmap gives me: Starting Nmap 5.00 ( http://nmap.org ) at 2012-03-20 16:15 CDT Interesting ports on xx.xxx.xx.x: Not shown: 995 closed ports PORT STATE SERVICE 21/tcp open ftp 22/tcp open ssh 53/tcp open domain 139/tcp open netbios-ssn 445/tcp open microsoft-ds Nmap done: 1 IP address (1 host up) scanned in 0.15 seconds My only hypothesis is that this has something to do with iptables. Maybe it's allowing only established connections? I don't think that's how I set it up, but maybe? Here's my iptables rules for INPUT: lucas@rearden:~$ sudo iptables -L INPUT Chain INPUT (policy DROP) target prot opt source destination fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh ufw-before-logging-input all -- anywhere anywhere ufw-before-input all -- anywhere anywhere ufw-after-input all -- anywhere anywhere ufw-after-logging-input all -- anywhere anywhere ufw-reject-input all -- anywhere anywhere ufw-track-input all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere tcp dpt:ftp I'm using vsftpd. Any thoughts/resources on how I could fix this? L

  Read the article

• Tkinter on Ubuntu 14.04 seems not to work

  - by empedokles

  I receive following Traceback: Traceback (most recent call last): File "tkinter_basic_frame.py", line 4, in <module> from Tkinter import Tk, Frame, BOTH File "/usr/lib/python2.7/lib-tk/Tkinter.py", line 42, in raise ImportError, str(msg) + ', please install the python-tk package' ImportError: No module named _tkinter, please install the python-tk package This is the demoscript I'm trying to run: #!/usr/bin/python # -*- coding: utf-8 -*- from Tkinter import Tk, Frame, BOTH class Example(Frame): def __init__(self, parent): Frame.__init__(self, parent, background="white") self.parent = parent self.initUI() def initUI(self): self.parent.title("Simple") self.pack(fill=BOTH, expand=1) def main(): root = Tk() root.geometry("250x150+300+300") app = Example(root) root.mainloop() if __name__ == '__main__': main() From my knowledge Tkinter should be included in Python 2.7. Why do I receive the traceback? Doesn't ubuntu contain the standard-python-distribution? This is solved. I had to install it manually in synaptic (got the hint in the meantime from another forum), see here: Wikipedia says: "Tkinter is a Python binding to the Tk GUI toolkit. It is the standard Python interface to the Tk GUI toolkit1 and is Python's de facto standard GUI,2 and is included with the standard Windows and Mac OS X install of Python." - Not good, that it isn't included in Ubuntu as well. Tkinter on Wikipedia

  Read the article

• Wireless Problem on Acer Aspire 5610z

  - by Ugur Can Yalaki

  I installed ubuntu 12.04 on my machine, but I can't get wireless connection to work. My computer is Acer Aspire 5610z. I found that some other people that have same computer, face the same problem. Here is some information about it: ****** info trace ****** * uname -a * Linux ucy-Aspire-5610Z 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:22:28 UTC 2013 i686 i686 i386 GNU/Linux * lsb_release * Distributor ID: Ubuntu Description: Ubuntu 12.04.3 LTS Release: 12.04 Codename: precise * lspci * 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) Subsystem: AMBIT Microsystem Corp. Device [1468:0422] Kernel driver in use: b43-pci-bridge 06:01.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02) Subsystem: Acer Incorporated [ALI] Device [1025:0090] Kernel driver in use: b44 * lsusb * Bus 001 Device 004: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 5986:0100 Acer, Inc Orbicam Bus 002 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub * PCMCIA Card Info * PRODID_1="" PRODID_2="" PRODID_3="" PRODID_4="" MANFID=0000,0000 FUNCID=255 * iwconfig * * rfkill * 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no * lsmod * ssb_hcd 12781 0 ssb 51554 2 ssb_hcd,b44 * nm-tool * NetworkManager Tool State: connected (global) Device: usb0 [Wired connection 2] ------------------------------------------- Type: Wired Driver: rndis_host State: connected Default: yes HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: on IPv4 Settings: Address: 192.168.42.7 Prefix: 24 (255.255.255.0) Gateway: 192.168.42.129 DNS: 192.168.42.129 IPv6 Settings: Address: ::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 Address: fe80::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 DNS: fe80::504d:76ff:fe86:db04 Device: eth2 ----------------------------------------------------------------- Type: Wired Driver: b44 State: unavailable Default: no HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: off * NetworkManager.state * [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true * NetworkManager.conf * [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false * interfaces * auto lo iface lo inet loopback * iwlist * * resolv.conf * nameserver 127.0.0.1 * blacklist * [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist-bcm43.conf] blacklist b43 blacklist b43legacy blacklist ssb blacklist bcm43xx blacklist brcm80211 blacklist brcmfmac blacklist brcmsmac blacklist bcma [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac * modinfo * filename: /lib/modules/3.8.0-32-generic/kernel/drivers/usb/host/ssb-hcd.ko license: GPL description: Common USB driver for SSB Bus author: Hauke Mehrtens srcversion: E127A51EDC8F44D2C2A8F15 alias: ssb:v4243id0819rev* alias: ssb:v4243id0817rev* alias: ssb:v4243id0808rev* depends: ssb intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 filename: /lib/modules/3.8.0-32-generic/kernel/drivers/ssb/ssb.ko license: GPL description: Sonics Silicon Backplane driver srcversion: 14621F6EC014F731244437C alias: pci:v000014E4d00004350sv*sd*bc*sc*i* alias: pci:v000014E4d0000432Csv*sd*bc*sc*i* alias: pci:v000014E4d0000432Bsv*sd*bc*sc*i* alias: pci:v000014E4d00004329sv*sd*bc*sc*i* alias: pci:v000014E4d00004328sv*sd*bc*sc*i* alias: pci:v000014E4d00004325sv*sd*bc*sc*i* alias: pci:v000014E4d00004324sv*sd*bc*sc*i* alias: pci:v000014E4d0000A8D6sv*sd*bc*sc*i* alias: pci:v000014E4d00004322sv*sd*bc*sc*i* alias: pci:v000014E4d00004321sv*sd*bc*sc*i* alias: pci:v000014E4d00004320sv*sd*bc*sc*i* alias: pci:v000014E4d00004319sv*sd*bc*sc*i* alias: pci:v000014A4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004315sv*sd*bc*sc*i* alias: pci:v000014E4d00004312sv*sd*bc*sc*i* alias: pci:v000014E4d00004311sv*sd*bc*sc*i* alias: pci:v000014E4d00004307sv*sd*bc*sc*i* alias: pci:v000014E4d00004306sv*sd*bc*sc*i* alias: pci:v000014E4d00004301sv*sd*bc*sc*i* depends: intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 * udev rules * PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb1:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb2:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb3:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2" * dmesg * [ 2.385241] ssb: Found chip with id 0x4311, rev 0x01 and package 0x00 [ 2.385256] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243) [ 2.385266] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243) [ 2.385276] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243) [ 2.385286] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243) [ 2.448147] ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0 [ 2.468112] ssb: Found chip with id 0x4401, rev 0x02 and package 0x00 [ 2.468124] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243) [ 2.468132] ssb: Core 1 found: V90 (cc 0x807, rev 0x03, vendor 0x4243) [ 2.468140] ssb: Core 2 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243) [ 2.508230] ssb: Sonics Silicon Backplane found on PCI device 0000:06:01.0 [ 2.528620] b44 ssb1:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver ******** done ******** Thank you already for your help.

  Read the article

• Inspiron N7110 Ubuntu 12.04 Poor WiFi Signal

  - by Joseph Risley

  Sorry if this is a repeat, I have been Googling possible answers and have not found one yet. I find my wireless signal is never 100%. Speed is fine, it's the actual signal strength that is the issue. I thought my router was the issue, but the problem was also present at the public library today. I asked the Windows and Mac users around me about their signal strength and they had full signal while mine was medium to low according to WiFiRadar. Is this a Dell problem (Realtek), or an Ubuntu problem I can fix in the terminal?

  Read the article

• Wine 1.2 crash after I start Mega 5.0

  - by Tomáš Šíma

  I installed Mega 5.0 by running "sudo sh MEGA5_Setup_deb_v2.sh" The application downloaded wine 1.2 as mega requires in order to work under Ubuntu. However every time I start the application through the icon provided, wine crashes asking me to send/save bug report, the problem is that if I choose to do so, megas starting window pops up covering the bug report window leaving me unable to do anything (as it won't move) The only solution I have come up with is to log out and log back in, as I cancels wine. I beg you following: Please post detailed step by step instructions how to deal with said problem Tell me if forceful log out, can damage computer of any of my data Please forgive me my weak English as it is not my native language. Also forgive me my weak skills concerning Ubuntu usage as I have me forced to switch to Ubuntu this very day. Thank you.

  Read the article

• How to fix no splash screen in Ubuntu after nvidia proprietary driver installation (also black borders)

  - by Fabio Trevisiol

  This is soultion how to fix no splash screen in Ubuntu after nvidia proprietary driver installation. It's no matter what Ubuntu version you use, it should work anyway. (TESTED ON 14.04) Open your terminal and type: sudo apt-get install v86d (TEST WITHOUT) Then: sudo gedit /etc/default/grub Find this line: #GRUB_GFXMODE=640x480 Add below (of course choose your resolution): GRUB_GFXMODE=1024x768x32 (TRY WITHOUT OR DIFFERENT BIT DEPTH) GRUB_GFXPAYLOAD_LINUX=1920x1080x32 (YOU CAN ALSO USE THE KEEP OPTION) Save file and type in terminal: echo FRAMEBUFFER=y | sudo tee /etc/initramfs-tools/conf.d/splash (ALLOWS TO AVOID THAT THE SPLASH SCREEN IS DISPLAYED FOR A FEW SECONDS) sudo update-initramfs -u sudo update-grub2 For all those who complain about the presence of black borders in "plymouth", try to make these changes before installing the nvidia driver or switch back from nvidia to nouveau and from nouveau to nvidia. Kernel update from the Software Updater? It happened to me; I don't know if it matters. I don't know for which of these reasons, but after a few reboots, the black borders are gone. UPDATE discovered the secret: during all these beautiful things, something strange happened. glxinfo | grep vendor server glx vendor string: SGI client glx vendor string: Mesa Project and SGI OpenGL vendor string: nouveau

  Read the article

• I attempted to install cuda drivers, and now almost everything is broken

  - by Nathan

  I tried to install CUDA tookit 5.0 on ubuntu 12.04 and the installation proceeded OK. After rebooting however, all I get is a terminal login. I've attempted to start the display manager with sudo start lightdm and it says all OK, but just hangs the prompt when it finishes loading without ever starting any display manager. sudo start gdm just flickers and goes back to the prompt. There is no network connection on the machine either. It usually connects to a wireless network with remembered credentials. What can I do to recover the machine?

  Read the article

• Linux Mint: How do I autorun rdp script?

  - by Rommel

  HI to all my name is Rommel... I'm new to Linux system coz im more into windows, but now i wanna try Linux os. I have this Linux Mint and i installed it on to one of my desktop PC, i have downloaded and installed freerdp-x11 for me to connect into my windows terminal server...The thing that I really need help is, i want the terminal command line to connect automatically to the windows terminal server so that every time i boot my Linux Mint pc i wouldn't have to keep typing "xfreerdp 000.000.0.000" on the terminal command line...Is there a script for it..???? PLease guys i really need your help on this... You can email me at this address: [email protected] or [email protected] Thanks in advance.

  Read the article

• What word processor can manage left and right pages separately?

  - by chtfn

  I was after a word processor that can manage left and right pages separately so I can have my text on the right pages and my illustrations on the left pages. I know LibeOffice can set "left page" and "right page" formats, but there is no simple way to make the text jump from right page to right page when writing. I don't know what would be the best way to do that, but I guess I need an app that is designed for writing books and do that kind of thing, or an app that can associate a page format with an object format (so the "illustration" format can be exclusively associated with "left page" format, and "text body" exclusively associated with "right page", for example). Or is there an extension for LO or OOo out there that I didn't hear about? Cheers!

  Read the article

• how to Acces Blocked Sites?

  - by Muhammad AYUB Khan BALOUCH

  im in Pakistan and Youtube is blocked in Pakistan . i want to take the Lecture videos from youtube. in windows i was using Hotsopshield to bypass proxy but now in Ubuntu i dnt know how to Bypass Proxy . i found some where that i can bypas proxy by Putty software . can u guide me how can i bypass proxy by that. but i was not able to do so . kindly tell me some easy method to bypass proxy . i dnt want to used websites like accesstoblockedsites.com

  Read the article

• WPA2 authentication fails using USB network devices (Linksys and Rosewill)

  - by Greg Youtz

  Decided to reduce the clutter in the house and replace a wired connection with a wireless one on my wife's system using USB network device Rosewill RNX-X1. I can see and connect to unprotected network, but WPA2 authentication repeatedly fails. Tried the same with a Linksys USB network adapter. Both failed to authenticate. Worth noting that I recently switched from Comcast to CenturyLink and so switched routers. The system connected successfully to previous router (Linksys EA4500) using WPA2. Would think it is the router (Actiontec C1000A) but all other devices (TV, iPad, Windows, Blackberry, and Squeezebox) connect ok. Would appreciate some diagnostic guidance and insight (phrased for a newbie!) Tests to date: sudo lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 01 serial: 00:e0:4d:30:40:a1 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:47 ioport:ac00(size=256) memory:fdcff000-fdcfffff memory:fdb00000-fdb1ffff *-network description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan1 serial: 00:02:6f:bd:30:a0 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.2.0-31-generic firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn sudo lspci -v 00:00.0 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- 00:01.0 ISA bridge: NVIDIA Corporation MCP67 ISA Bridge (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 00:01.1 SMBus: NVIDIA Corporation MCP67 SMBus (rev a2) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: 66MHz, fast devsel, IRQ 11 I/O ports at fc00 [size=64] I/O ports at 1c00 [size=64] I/O ports at 1c40 [size=64] Capabilities: [44] Power Management version 2 Kernel driver in use: nForce2_smbus Kernel modules: i2c-nforce2 00:01.2 RAM memory: NVIDIA Corporation MCP67 Memory Controller (rev a2) Flags: 66MHz, fast devsel 00:02.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 Memory at fe02f000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:02.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe02e000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:04.0 USB controller: NVIDIA Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fe02d000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Kernel driver in use: ohci_hcd 00:04.1 USB controller: NVIDIA Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20 Memory at fe02c000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Kernel driver in use: ehci_hcd 00:06.0 IDE interface: NVIDIA Corporation MCP67 IDE Controller (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Biostar Microtech Int'l Corp Device 3409 Flags: bus master, 66MHz, fast devsel, latency 0 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at f000 [size=16] Capabilities: [44] Power Management version 2 Kernel driver in use: pata_amd Kernel modules: pata_amd 00:07.0 Audio device: NVIDIA Corporation MCP67 High Definition Audio (rev a1) Subsystem: Biostar Microtech Int'l Corp Device 820c Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22 Memory at fe024000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:08.0 PCI bridge: NVIDIA Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000c000-0000cfff Memory behind bridge: fdf00000-fdffffff Prefetchable memory behind bridge: fd000000-fd0fffff Capabilities: [b8] Subsystem: NVIDIA Corporation Device cb84 Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- 00:09.0 IDE interface: NVIDIA Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: Biostar Microtech Int'l Corp Device 5407 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23 I/O ports at 09f0 [size=8] I/O ports at 0bf0 [size=4] I/O ports at 0970 [size=8] I/O ports at 0b70 [size=4] I/O ports at dc00 [size=16] Memory at fe02a000 (32-bit, non-prefetchable) [size=8K] Capabilities: [44] Power Management version 2 Capabilities: [8c] SATA HBA v1.0 Capabilities: [b0] MSI: Enable- Count=1/8 Maskable- 64bit+ Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: ahci 00:0b.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000b000-0000bfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fddfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0c.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 I/O behind bridge: 0000a000-0000afff Memory behind bridge: fdc00000-fdcfffff Prefetchable memory behind bridge: 00000000fdb00000-00000000fdbfffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0d.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 I/O behind bridge: 00009000-00009fff Memory behind bridge: fda00000-fdafffff Prefetchable memory behind bridge: 00000000fd900000-00000000fd9fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0e.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 I/O behind bridge: 00008000-00008fff Memory behind bridge: fd800000-fd8fffff Prefetchable memory behind bridge: 00000000fd700000-00000000fd7fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:0f.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00007000-00007fff Memory behind bridge: fd600000-fd6fffff Prefetchable memory behind bridge: 00000000fd500000-00000000fd5fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:10.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 I/O behind bridge: 00006000-00006fff Memory behind bridge: fd400000-fd4fffff Prefetchable memory behind bridge: 00000000fd300000-00000000fd3fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 PCI bridge: NVIDIA Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: fd200000-fd2fffff Prefetchable memory behind bridge: 00000000fd100000-00000000fd1fffff Capabilities: [40] Subsystem: NVIDIA Corporation Device 0000 Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Capabilities: [80] Express Root Port (Slot+), MSI 00 Capabilities: [100] Virtual Channel Kernel driver in use: pcieport Kernel modules: shpchp 00:12.0 VGA compatible controller: NVIDIA Corporation C68 [GeForce 7050 PV / nForce 630a] (rev a2) (prog-if 00 [VGA controller]) Subsystem: Biostar Microtech Int'l Corp Device 1406 Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21 Memory at fb000000 (32-bit, non-prefetchable) [size=16M] Memory at e0000000 (64-bit, prefetchable) [size=256M] Memory at fc000000 (64-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at 80000000 [disabled] [size=128K] Capabilities: [48] Power Management version 2 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Kernel driver in use: nvidia Kernel modules: nvidia_current, nouveau, nvidiafb 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration Flags: fast devsel Capabilities: [80] HyperTransport: Host or Secondary Interface 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map Flags: fast devsel 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller Flags: fast devsel 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control Flags: fast devsel Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp Kernel modules: k8temp 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) Subsystem: Biostar Microtech Int'l Corp Device 2305 Flags: bus master, fast devsel, latency 0, IRQ 47 I/O ports at ac00 [size=256] Memory at fdcff000 (64-bit, non-prefetchable) [size=4K] [virtual] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [40] Power Management version 2 Capabilities: [48] Vital Product Data Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Capabilities: [60] Express Endpoint, MSI 00 Capabilities: [84] Vendor Specific Information: Len=4c <?> Capabilities: [100] Advanced Error Reporting Capabilities: [12c] Virtual Channel Capabilities: [148] Device Serial Number 32-00-00-00-10-ec-81-68 Capabilities: [154] Power Budgeting <?> Kernel driver in use: r8169 Kernel modules: r8169 sudo rfkill list all 2: phy2: Wireless LAN Soft blocked: no Hard blocked: no Would appreciate insight on how to chase this down.

  Read the article

• High load (and high temp) with idle processes

  - by Nanne

  I've got a semi-old laptop (toshiba satellite a110-228), that's appointed 'laptop for the kids' by my sister. I've installed ubuntu netbook (10.10) on it because of the lack-of memory and it seems to work fine, accept from some heat-issues. These where never a problem under windows. It looks like I've got something similar to this problem: Load is generally 1 or higher, sometimes its stuck at 0.80, but its way to high. Top/htop only show a couple of percentage CPU use (which isn't too shocking, as i'm not doing anything). At this point all the software is stock, and i'd like to keep it that way because its supposed to be the easy-to-maintain kids computer. Now I'd like to find out: What could be the cause of the high load? Could it be as this thread implies, some driver, are there other options to check? How could I see what is really keeping the system hot and bothered? How to check what runs, etc etc? I'd like to pinpoint the culprint. further steps to take for debugging? The big bad internet leads me to believe that it might be the graphics drivers. The laptop has an Intel 945M chipset, but that doesn't seem to be one of the problem childs in this manner (I read a lot abotu ATI drivers that need special isntall). I'd not only welcome hints to directly solve this (duh) but also help in starting to debug what is going on. I am really hesitant in installing an older kernel, as I want it to be stock, and easy upgradeable (because I don't live near it, it should run without me ;) ) As an afterthought: to keep the whole thing cooler, can I 'amp up' the fancontrol? Its only going "airplane" mode when the computer is 95 Celcius, which is a tad late for my taste. Top: powertop:

  Read the article

• Ubuntu 12.04 NVIDIA GeForce Go 7600 black screen during boot

  - by Florian Schmidt

  I'm using Ubuntu as the only operating system since two years. In the first Ubuntu versions I had seen my BIOS screen and the boot screens. Actually im using Ubuntu 12.04 and my screen stays black until Ubuntu is started (both screens are missing). I guess this situation appeared the first time in Ubuntu 11 (not sure). I searched via google and tried the popular activities but was not able to fix my issue. I opened the laptop and checked all connections. I'm using boot option nomodeset. I had a look through many many web pages. I don't know how to continue and hope somebody could be helpful. My hardware: Acer Aspire 9300 AMD Turion 64 x2 NVIDIA GeForce Go 7600 (using proposed driver) lspci | grep NVIDIA 00:00.0 RAM memory: NVIDIA Corporation C51 Host Bridge (rev a2) 00:00.1 RAM memory: NVIDIA Corporation C51 Memory Controller 0 (rev a2) 00:00.2 RAM memory: NVIDIA Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: NVIDIA Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: NVIDIA Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: NVIDIA Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: NVIDIA Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: NVIDIA Corporation C51 Memory Controller 2 (rev a2) 00:02.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:03.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:04.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:09.0 RAM memory: NVIDIA Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: NVIDIA Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: NVIDIA Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: NVIDIA Corporation MCP51 PMU (rev a3) 00:0b.0 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: NVIDIA Corporation MCP51 IDE (rev f1) 00:0e.0 IDE interface: NVIDIA Corporation MCP51 Serial ATA Controller (rev f1) 00:10.0 PCI bridge: NVIDIA Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: NVIDIA Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: NVIDIA Corporation MCP51 Ethernet Controller (rev a3) 03:00.0 VGA compatible controller: NVIDIA Corporation G73 [GeForce Go 7600] (rev a1) So my question is what to do to fix the black screen during boot?

  Read the article

• Segmentation fault in Ubuntu One Music

  - by maxroby

  When clicking on the "My Downloads" button in Ubuntu One Music the application crashes with a segmentation fault, showing the following terminal messages: ** Message: console message: @0: The page at https://one.ubuntu.com/music/store/library displayed insecure content from http://media.one.ubuntu.com/media/img/favicon.ico. Errore di segmentazione (core dump creato) So i can't access my Ubuntu One Music downloads from inside Rhythmbox.

  Read the article

• Convert DVD to MKV (et al) without transcoding/recompression

  - by Oli

  Like a lot of people, I have a lot of DVDs. But we also have a stupid amount of disk space and a media centre (Boxee) so the DVDs are getting less and less use. It would be nice to convert our DVDs into something more relevant to our needs. I've dabbled with DVD ripping before but whereas I'd usually transcode down to a smaller picture size with a better video compression algorithm, this takes a silly amount of time. I don't have a couple of hours available for each disk. (Sidebar: is there dedicated, Linux-friendly hardware to improve h264 encoding performance?) So I was wondering if there's anything that take the DVD filesystem, De-CSS it, and then stitch together any the VOBs that make up the main part of the film and package that up in a wrapping format like MKV. A bonus would be if it could grab the subtitles and stick them in too but that's not a requirement as Boxee can grab the subtitles online if it needs to.

  Read the article

• How to install suggested packages in apt-get

  - by Alaa Ali

  EDIT: I solved my issue. I will answer my own question, but in 5 hours because I don't have permission now. I know the question has been asked before, but please hear me out. So I wanted to install screenlets. I ran sudo apt-get install screenlets, and this is what I got: The following extra packages will be installed: libart-2.0-2 libbonobo2-0 libbonobo2-common libbonoboui2-0 libbonoboui2-common libgnome2-0 libgnomecanvas2-0 libgnomecanvas2-common libgnomeui-0 libgnomeui-common libtidy-0.99-0 python-beautifulsoup python-evolution python-feedparser python-gmenu python-gnome2 python-numpy python-pyorbit python-rsvg python-tz python-utidylib screenlets-pack-basic Suggested packages: libbonobo2-bin python-gnome2-doc python-numpy-doc python-numpy-dbg python-nose python-dev gfortran python-pyorbit-dbg screenlets-pack-all python-dcop Recommended packages: python-numeric python-gnome2-extras The following NEW packages will be installed: libart-2.0-2 libbonobo2-0 libbonobo2-common libbonoboui2-0 libbonoboui2-common libgnome2-0 libgnomecanvas2-0 libgnomecanvas2-common libgnomeui-0 libgnomeui-common libtidy-0.99-0 python-beautifulsoup python-evolution python-feedparser python-gmenu python-gnome2 python-numpy python-pyorbit python-rsvg python-tz python-utidylib screenlets screenlets-pack-basic 0 upgraded, 23 newly installed, 0 to remove and 2 not upgraded. People say that Recommended packages are installed by default, but they are clearly not included in the NEW packages that will be installed above. I also decided to include the Suggested packages in the installation, so I ran sudo apt-get --install-suggests install screenlets instead, but I got a HUGE list of NEW packages that will be installed; that number is precisely 0 upgraded, 944 newly installed, 0 to remove and 2 not upgraded. Should'nt I be getting only around 10 extra packages?

  Read the article

• Make one monitor act like two, split in half

  - by Nathan J. Brauer

  Context: Ubuntu 11.10, Unity Let's say I have a screen at resolution 1000x500. What I'd like to do is split the screen down the middle so [Unity or X or ?] acts as if there are two displays (each of 500x500). Examples: Unity will display a different toolbar (the top one) on each side of the display. If I maximize a window on the left side of the screen, it will fill the left side only. If I maximize on the right, it will fill the right. If I hit "fullscreen" in youtube (flash) or Chrome or Movie Player, it will only fill the side of the display that it's on. If it's really is impossible to do this with Unity, will it work with Gnome3 and how? A million thanks!

  Read the article

• sensors reporting weird temperatures

  - by Felix

  lm-sensors is reporting weird temps for me: $ sensors coretemp-isa-0000 Adapter: ISA adapter Core 0: +38.0°C (high = +72.0°C, crit = +100.0°C) coretemp-isa-0001 Adapter: ISA adapter Core 1: +35.0°C (high = +72.0°C, crit = +100.0°C) coretemp-isa-0002 Adapter: ISA adapter Core 2: +32.0°C (high = +72.0°C, crit = +100.0°C) coretemp-isa-0003 Adapter: ISA adapter Core 3: +42.0°C (high = +72.0°C, crit = +100.0°C) w83627dhg-isa-0290 Adapter: ISA adapter Vcore: +1.10 V (min = +0.00 V, max = +1.74 V) in1: +1.62 V (min = +0.06 V, max = +0.17 V) ALARM AVCC: +3.34 V (min = +2.98 V, max = +3.63 V) VCC: +3.34 V (min = +2.98 V, max = +3.63 V) in4: +1.83 V (min = +1.30 V, max = +1.15 V) ALARM in5: +1.26 V (min = +0.83 V, max = +1.03 V) ALARM in6: +0.11 V (min = +1.22 V, max = +0.56 V) ALARM 3VSB: +3.30 V (min = +2.98 V, max = +3.63 V) Vbat: +3.18 V (min = +2.70 V, max = +3.30 V) fan1: 0 RPM (min = 0 RPM, div = 128) ALARM fan2: 1117 RPM (min = 860 RPM, div = 8) fan3: 0 RPM (min = 10546 RPM, div = 128) ALARM fan4: 0 RPM (min = 10546 RPM, div = 128) ALARM fan5: 0 RPM (min = 10546 RPM, div = 128) ALARM temp1: +88.0°C (high = +20.0°C, hyst = +4.0°C) ALARM sensor = diode temp2: +25.0°C (high = +80.0°C, hyst = +75.0°C) sensor = diode temp3: +121.5°C (high = +80.0°C, hyst = +75.0°C) ALARM sensor = thermistor cpu0_vid: +2.050 V Please note temp3. How can I know what temp3 is, and why it is so high? The system is really stable (which I guess it wouldn't be at those temps). Also, note the really decent core temps, which suggest a healthy system as well. My guess is that the readout is wrong. On another computer it reported temperatures below 0 degrees centigrade, which was not possible, considering the environment temperature of ~22-24. Is this some known bug/issue? Should I try some Windows programs (like CPU-Z) and see they give similar results?

  Read the article

• Touchpad not working on an Acer One 725

  - by big-marc

  I installed ubuntu on a usb drive on a acer one 725, and cannot seem to be able to make the touchpad work....here is what i have xinpbig-marc@Big-Marc:~$ xinput --list ? Virtual core pointer id=2 [master pointer (3)] ? ? Virtual core XTEST pointer id=4 [slave pointer (2)] ? ? Logitech USB Optical Mouse id=10 [slave pointer (2)] ? ? ETPS/2 Elantech Touchpad id=13 [slave pointer (2)] any can help me out....

  Read the article

< Previous Page | 131 132 133 134 135 136 137 138 139 140 141 142  | Next Page >