Search Results

Search found 33971 results on 1359 pages for 'ask and learn'.

Page 137/1359 | < Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >

• Intel graphics driver installer, now the CPU fan is rarely quiet

  - by Space monkey

  I have an Optimus chipset: Intel HD 4000 (i7-3635QM CPU) Geforce 640m I don't care about the NVIDIA card, so I didn't try to install any proprietary drivers for it. So: I was having a choppy+high CPU experience with gnome-shell on Ubuntu 14.04. Only happened when I tried moving a window around quickly. I used the Intel graphics installer hoping that it will fix the problem. It did fix the problem, now there is no choppyness or high CPU when I move windows around. However, there is a new problem now: The fan is rarely quiet, doing barely anything at all will cause the fan to go into loud mode quickly. That happens despite the CPU usage being at just around 4%. This wasn't the case before installing Intel drivers. It would normally only do that if, for example, I'm installing packages or doing something that puts some stress on the CPU. I set all CPU cores to "powersave" using cpufreq-set, but nothing changed. Also on Windows, the fans are really quiet when I'm in powersave mode. I believe they completely shut off for most of the time. I remember the installer giving me a report at the end as to which packages it installed. Unfortunately, I didn't save the report and I don't know where it would have saved it if it did. Any ideas or similar experiences?

  Read the article

• How do I fix a corrupted harddrive after failed upgrade?

  - by Nil

  The problem originated when I was trying to fix this problem. Things went horribly, horribly wrong and I ended up with a new problem altogether. The last thing I did was run sudo apt-get install and that caused my system to freeze. I restarted my computer and it would not boot from the harddrive. I ran a copy of Ubuntu 12.10 from a flashdrive that I had and ran gparted to see if my partitions were all there. It returned this message: Invalid partition table on /dev/sda -- wrong signature 5208. The drive appeared as a 2TiB unallocated drive with an error. The drive had 4 partitions before (plus random unallocated space). There was a fat32 partition, an ext4 partition which contained ubuntu 13.04/13.10 (I don't even know which one at this point), an extended partition which contained a swap partition for my ubuntu partition (I was meaning to move that ubuntu partition into the extended partition, never got around to it), and another partition (I don't remember how I formatted it). I should also mention this is a 1TB harddrive. So in short, I have a corrupted partition table on my primary harddrive from which I boot from, how can I fix this? I tried mounting the drive with sudo mount /dev/sda1 /media/ubuntu then I changed my directory to said folder and tried to list files and this monstrosity happened: $ ls ls: cannot access ??w?j^?.: Input/output error ls: cannot access ??(? ?x?.|: Input/output error ls: cannot access 6W_@?)?._??: Input/output error ls: cannot access HB0v???.A}?: Input/output error ls: cannot access ???.?X: Input/output error ls: cannot access t)?.+?l: Input/output error ls: cannot access ?h@ ?.@ : Input/output error ls: cannot access >? @??.???: Input/output error ls: cannot access m???.??: Input/output error ls: cannot access @ if??a?: Input/output error ls: cannot access ?M!vN$?.??n: Input/output error ls: cannot access ?o? ??.Bm`: Input/output error ls: cannot access ?:I??? M. : Input/output error ls: cannot access W??.??: Input/output error ls: cannot access ?: Input/output error ls: cannot access ?W?s??: Input/output error ls: cannot access ?v?k?.???: Input/output error ls: cannot access 5?$<N??: Input/output error .x????.??i: Input/output error ls: cannot access je????.j?1: Input/output error XjD?.???: Input/output error ls: cannot access W??n???.?: Input/output error ls: cannot access ?^x.$"?: Input/output error ls: cannot access !??*!??j.??: Input/output error ls: cannot access '-??k?^?.???: Input/output error ls: cannot access b?w?w?b.\??: Input/output error ls: cannot access o????"z.??B: Input/output error ls: cannot access ??b?h.?3-: Input/output error ls: cannot access ??.$7: Input/output error ls: cannot access )??K.bk: Input/output error ls: cannot access s??z?.?(?: Input/output error ls: cannot access ?F@?0?.@?: Input/output error .?D: Input/output error .??: Input/output error ls: cannot access?????. @: Input/output error ls: cannot access ?/?? ?.??: No such file or directory ls: cannot access rk?p4q(?.?k: Input/output error This looks promising. This is the output of fdisk -l $ sudo fdisk -l /dev/sda Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: invalid flag 0x5208 of partition table 5 will be corrected by w(rite) Disk /dev/sda: 2199.0 GB, 2199023132672 bytes 255 heads, 63 sectors/track, 267349 cylinders, total 4294967056 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x44fdfe06 Device Boot Start End Blocks Id System /dev/sda1 113305600 894715903 390705152 c W95 FAT32 (LBA) /dev/sda2 894715904 1489307647 297295872 83 Linux /dev/sda3 1489309694 1497307135 3998721 5 Extended /dev/sda4 1497309184 1953523711 228107264 7 HPFS/NTFS/exFAT /dev/sda5 ? 3013257822 3688738171 337740175 aa Unknown

  Read the article

• KMenu & shell script

  - by allenskd

  I'm trying to make a very small shell script with a simple command and add it up to the KMenu. Well, thing is that once it launches the shell script, it closes it fast and I want to leave it open because the shell script attempts to create run a web application using a framework. I tried with this first #!/bin/bash play run /home/david/Projects/ZS then I tried with this #!/bin/bash konsole -e play run /home/david/Projects/ZSBlackboard In terminal, it runs perfectly, but in launcher.. not so much Any solution or suggestion is appreciated, thanks

  Read the article

• I can't upgrade 13.10 because of broken pipe

  - by user212179

  I try upgrading and this is what I get: christopher@chris-computer:~$ sudo apt-get upgrade [sudo] password for christopher: Reading package lists... Done Building dependency tree Reading state information... Done The following packages will be upgraded: librhythmbox-core7 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B/809 kB of archives. After this operation, 39.9 kB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 170617 files and directories currently installed.) Preparing to replace librhythmbox-core7 2.99.1-0ubuntu1 (using .../librhythmbox-core7_3.0.1-0~13.10~ppa1_i386.deb) ... Unpacking replacement librhythmbox-core7 ... dpkg: error processing /var/cache/apt/archives/librhythmbox-core7_3.0.1-0~13.10~ppa1_i386.deb (--unpack): trying to overwrite '/usr/lib/librhythmbox-core.so.8.0.0', which is also in package librhythmbox-core8 3.0.1-1ubuntu2~ppa0 No apport report written because MaxReports is reached already dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Errors were encountered while processing: /var/cache/apt/archives/librhythmbox-core7_3.0.1-0~13.10~ppa1_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• Multiple computers on Ubuntu One

  - by L R Bellmore Jr

  I have added files from 4 computers to Ubuntu One. One computer failed. What happens to the files that I uploaded. Are they still on Ubuntu One? How come when I upload a file from computer A, computer B with the same Ubuntu One account does not sync and load that file into computer B - That has created this question.. what happens to files from computers from which I uploaded documents when those computers are no longer active or failed, or no longer have Ubuntu One on that computer from which the files were uploaded... Have I lost the files? The followup question is how come files from Computer A uploaded to Ubuntu One don't sync to Computer B. That is a related question. I need to shut down a computer, reformat the hard drive and install Linux on the entire harddrive instead of a dual boot with Windows XP as I am going to use Virtual Machines instead.. what happens to the files from the Windows Dual Boot that were uploaded to Ubuntu One? Are they removed from Ubuntu One and then have I lost those files if I don't backup to another service first.

  Read the article

• Can't install Catalyst 12.8

  - by Dominic Jordan Hasford

  I can not install fglrx ATI drivers/Catalyst 12.8. I have tried installing AMA Catalyst 12.8 using this guide: http://www.upubuntu.com/2012/08/install-amd-catalyst-128-on-ubuntu.html When I reach the part of installing with sudo sh amd-driver-installer-8.982-x86.x86_64.run , I get the following error: When I run it using the --force option, I get this message: How can I fix these errors and install Catalyst 12.8?

  Read the article

• "/etc/init.d/networking restart" with non-root user

  - by bonchen

  I have a thin client with 112mb RAM which boots ubuntu server 12.04.1 from a usb drive with openbox and it is to be used by students to communicate with cisco equipment. And because of this the students need to be able to reconfigure the network interface and then restart it without a reboot using the only user - cisco. This is what I have so far: adduser cisco usermod -a -G dialout cisco chown root:cisco /etc/network/interfaces chmod 664 /etc/network/interfaces chmod u+s /sbin/shutdown chmod u+s /sbin/reboot chmod u+s /sbin/poweroff chmod u+s /run/network/if* chmod u+s /sbin/ifdown chmod u+s /sbin/ifup And when I run /etc/init.d/networking restart as cisco I get: *Reconfiguring network interfaces... rm: cannot remove `eth0.dhclient': Permission denied Failed to send flush request: Operation not permitted RTNETLINK answers: Operation not permitted Any ideas on how to get this working? Thanks!

  Read the article

• Is there a way to update all Java related alternatives?

  - by James McMahon

  Is there a way to quickly switch over all the Java related alternatives using update-alternatives? For instance, if want to switch Java over to 7, I run sudo update-alternatives --config java and select the Java 7 OpenJdk. But if I run update-alternatives --get-selections | grep java I get the following, appletviewer auto /usr/lib/jvm/java-6-openjdk-amd64/bin/appletviewer extcheck auto /usr/lib/jvm/java-6-openjdk-amd64/bin/extcheck idlj auto /usr/lib/jvm/java-6-openjdk-amd64/bin/idlj itweb-settings auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/itweb-settings jar auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jar jarsigner auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jarsigner java manual /usr/lib/jvm/java-7-openjdk-amd64/jre/bin/java javac auto /usr/lib/jvm/java-6-openjdk-amd64/bin/javac javadoc auto /usr/lib/jvm/java-6-openjdk-amd64/bin/javadoc javah auto /usr/lib/jvm/java-6-openjdk-amd64/bin/javah javap auto /usr/lib/jvm/java-6-openjdk-amd64/bin/javap javaws auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/javaws jconsole auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jconsole jdb auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jdb jexec auto /usr/lib/jvm/java-6-openjdk-amd64/jre/lib/jexec jhat auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jhat jinfo auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jinfo jmap auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jmap jps auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jps jrunscript auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jrunscript jsadebugd auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jsadebugd jstack auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jstack jstat auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jstat jstatd auto /usr/lib/jvm/java-6-openjdk-amd64/bin/jstatd keytool auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/keytool native2ascii auto /usr/lib/jvm/java-6-openjdk-amd64/bin/native2ascii orbd auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/orbd pack200 auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/pack200 policytool auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/policytool rmic auto /usr/lib/jvm/java-6-openjdk-amd64/bin/rmic rmid auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/rmid rmiregistry auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/rmiregistry schemagen auto /usr/lib/jvm/java-6-openjdk-amd64/bin/schemagen serialver auto /usr/lib/jvm/java-6-openjdk-amd64/bin/serialver servertool auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/servertool tnameserv auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/tnameserv unpack200 auto /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/unpack200 wsgen auto /usr/lib/jvm/java-6-openjdk-amd64/bin/wsgen wsimport auto /usr/lib/jvm/java-6-openjdk-amd64/bin/wsimport xjc auto /usr/lib/jvm/java-6-openjdk-amd64/bin/xjc As you can see, my Java alternative was switched over to 7, but every other alternative based on OpenJDK 6 was not switched over. Sure I could switch each one manually or write a script to do so, but I assume there is a better way to accomplish this.

  Read the article

• iptables rules keep showing up

  - by Omriko

  I just installed an ubuntu precise server, after a few weird communications issues I checked the iptables list and found: Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- 10.0.0.0/24 anywhere tcp spts:1024:65535 dpt:ssh state NEW ACCEPT icmp -- anywhere anywhere state NEW ACCEPT icmp -- anywhere anywhere state NEW ACCEPT icmp -- anywhere anywhere state NEW ACCEPT icmp -- anywhere anywhere state NEW DROP tcp -- anywhere anywhere tcp dpt:10520 state NEW DROP udp -- anywhere anywhere udp spts:1:65535 dpt:31337 state NEW DROP udp -- anywhere anywhere udp spts:1:65535 dpt:31338 state NEW DROP udp -- anywhere anywhere udp spts:1:65535 dpt:54320 state NEW DROP udp -- anywhere anywhere udp spts:1:65535 dpt:54321 state NEW DROP tcp -- anywhere anywhere tcp dpt:12345 state NEW DROP tcp -- anywhere anywhere tcp dpt:12346 state NEW DROP tcp -- anywhere anywhere tcp dpt:20034 state NEW DROP tcp -- anywhere anywhere tcp dpt:16600 state NEW DROP tcp -- anywhere anywhere tcp dpt:16660 state NEW DROP tcp -- anywhere anywhere tcp dpt:65000 state NEW DROP udp -- anywhere anywhere udp dpt:34555 state NEW DROP udp -- anywhere anywhere udp dpt:35555 state NEW DROP udp -- anywhere anywhere udp spts:netbios-ns:netbios-dgm dpts:netbios-ns:netbios-dgm state NEW DROP tcp -- anywhere anywhere tcp spts:1024:65535 dpt:netbios-ssn state NEW DROP tcp -- anywhere anywhere tcp spts:1024:65535 dpt:microsoft-ds state NEW DROP udp -- anywhere anywhere udp spt:microsoft-ds dpt:microsoft-ds state NEW DROP udp -- anywhere anywhere udp spts:1024:65535 dpt:microsoft-ds state NEW DROP tcp -- anywhere anywhere tcp spts:1024:65535 dpt:loc-srv state NEW DROP tcp -- anywhere anywhere tcp spts:1024:65535 dpt:5000 state NEW DROP tcp -- anywhere anywhere tcp spts:1024:65535 dpts:1025:1029 state NEW DROP udp -- anywhere anywhere udp spts:1:65535 dpt:loc-srv state NEW ACCEPT tcp -- anywhere anywhere tcp spts:1024:65535 dpt:28082 state NEW DROP all -- anywhere anywhere state NEW Chain FORWARD (policy DROP) target prot opt source destination Chain OUTPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT tcp -- anywhere anywhere tcp spts:tcpmux:65535 dpts:tcpmux:65535 state NEW ACCEPT udp -- anywhere anywhere udp dpts:1:65535 state NEW ACCEPT icmp -- anywhere anywhere state NEW ACCEPT tcp -- anywhere anywhere tcp spts:1024:65535 dpt:28082 state NEW DROP all -- anywhere anywhere state NEW I tried to wipe the rules, I disabled UFW, Ive rewritten and saved iptables rules according to this guide, but every minute or so the old rules return.... I checked crontab for scheduled tasks, there is nothing in there but still these rules appear every minute... please help!

  Read the article

• Ubuntu CD Boots to Black Screen

  - by Thomas

  I have a new Asus N76 Notebook and just downloaded the lastest ubuntu 12.10 desktop CD (x64). When I boot from the CD, I get to the selection asking to try or install Ubuntu (the text screen not the one with the Ubuntu logo). When I select one of these options, I get only a black screen. I have tried nomodeset, acpi=off but it does not change anything. I also tried booting a CD and an USB stick (same result). I have no idea what to try next. I have installed Ubuntu on several computers yet, never had this problem. Any suggestions? Thanks in advance. Thomas

  Read the article

• bluez 5.19 PS4 controller

  - by Athanase

  I currently have a problem when pairing my computer with a PS4 remote. On my Ubuntu 14.04 I removed everything related with bluez and bluetooth, and I built and installed bluez 5.19. Here are some useful command outputs: jean@system ~ hcitool hcitool - HCI Tool ver 5.19 jean@system ~ hcitool dev Devices: hci0 00:15:83:4C:0C:BB jean@system ~ bluetoothctl [bluetooth]# version Version 5.19 jean@system ~ bluetoothctl [NEW] Controller 00:15:83:4C:0C:BB BlueZ [default] jean@system ~ lsusb Bus 003 Device 012: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) So here is what happens. When I try to hard pair the controller with the computer, by holding the share and ps button for a while, everything works as expected and the pairing is done properly. After a hard pairing if I try the pairing by pressing the ps button only, nothings happen. In order to go it, I first power up the bluetooth dongle: jean@system ~ sudo hciconfig hciX up and then I run the bluetooh deamon bluetoothd: jean@system /usr/libexec/bluetooth ~ ./bluetoothd -d -n bluetoothd[11270]: Bluetooth daemon 5.19 bluetoothd[11270]: src/main.c:parse_config() parsing main.conf bluetoothd[11270]: src/main.c:parse_config() discovto=0 bluetoothd[11270]: src/main.c:parse_config() pairto=0 bluetoothd[11270]: src/main.c:parse_config() auto_to=60 bluetoothd[11270]: src/main.c:parse_config() name=%h-%d bluetoothd[11270]: src/main.c:parse_config() class=0x000100 bluetoothd[11270]: src/main.c:parse_config() Key file does not have key 'DeviceID' bluetoothd[11270]: src/gatt.c:gatt_init() Starting GATT server bluetoothd[11270]: src/adapter.c:adapter_init() sending read version command bluetoothd[11270]: Starting SDP server bluetoothd[11270]: src/sdpd-service.c:register_device_id() Adding device id record for 0002:1d6b:0246:0513 ... bluetoothd[11270]: src/adapter.c:adapter_service_insert() /org/bluez/hci0 bluetoothd[11270]: src/adapter.c:add_uuid() sending add uuid command for index 0 bluetoothd[11270]: profiles/audio/a2dp.c:a2dp_sink_server_probe() path /org/bluez/hci0 bluetoothd[11270]: profiles/audio/a2dp.c:a2dp_source_server_probe() path /org/bluez/hci0 bluetoothd[11270]: src/adapter.c:btd_adapter_unblock_address() hci0 00:00:00:00:00:00 bluetoothd[11270]: src/adapter.c:get_ltk_info() A4:15:66:C1:0D:2A bluetoothd[11270]: src/device.c:device_create_from_storage() address A4:15:66:C1:0D:2A bluetoothd[11270]: src/device.c:device_new() address A4:15:66:C1:0D:2A bluetoothd[11270]: src/device.c:device_new() Creating device /org/bluez/hci0/dev_A4_15_66_C1_0D_2A bluetoothd[11270]: src/device.c:device_set_bonded() bluetoothd[11270]: src/adapter.c:get_ltk_info() A4:15:66:88:5E:9A bluetoothd[11270]: src/device.c:device_create_from_storage() address A4:15:66:88:5E:9A bluetoothd[11270]: src/device.c:device_new() address A4:15:66:88:5E:9A bluetoothd[11270]: src/device.c:device_new() Creating device /org/bluez/hci0/dev_A4_15_66_88_5E_9A bluetoothd[11270]: src/device.c:device_set_bonded() bluetoothd[11270]: src/adapter.c:load_link_keys() hci0 keys 2 debug_keys 0 bluetoothd[11270]: src/adapter.c:load_ltks() hci0 keys 0 bluetoothd[11270]: src/adapter.c:load_connections() sending get connections command for index 0 bluetoothd[11270]: src/adapter.c:adapter_service_insert() /org/bluez/hci0 bluetoothd[11270]: src/adapter.c:add_uuid() sending add uuid command for index 0 bluetoothd[11270]: src/adapter.c:set_did() hci0 source 2 vendor 1d6b product 246 version 513 bluetoothd[11270]: src/adapter.c:adapter_register() Adapter /org/bluez/hci0 registered bluetoothd[11270]: src/adapter.c:set_dev_class() sending set device class command for index 0 bluetoothd[11270]: src/adapter.c:set_name() sending set local name command for index 0 bluetoothd[11270]: src/adapter.c:set_mode() sending set mode command for index 0 bluetoothd[11270]: src/adapter.c:set_mode() sending set mode command for index 0 bluetoothd[11270]: src/adapter.c:adapter_start() adapter /org/bluez/hci0 has been enabled bluetoothd[11270]: src/adapter.c:trigger_passive_scanning() bluetoothd[11270]: plugins/hostname.c:property_changed() static hostname: system bluetoothd[11270]: plugins/hostname.c:property_changed() pretty hostname: bluetoothd[11270]: plugins/hostname.c:update_name() name: system bluetoothd[11270]: src/adapter.c:adapter_set_name() name: system bluetoothd[11270]: plugins/hostname.c:property_changed() chassis: desktop bluetoothd[11270]: plugins/hostname.c:update_class() major: 0x01 minor: 0x01 bluetoothd[11270]: src/adapter.c:load_link_keys_complete() link keys loaded for hci0 bluetoothd[11270]: src/adapter.c:load_ltks_complete() LTKs loaded for hci0 bluetoothd[11270]: src/adapter.c:get_connections_complete() Connection count: 0 And then I press the ps button of the PS4 controller bluetoothd[11270]: src/adapter.c:connected_callback() hci0 device A4:15:66:C1:0D:2A connected eir_len 5 bluetoothd[11270]: profiles/input/server.c:connect_event_cb() Incoming connection from A4:15:66:C1:0D:2A on PSM 17 bluetoothd[11270]: profiles/input/device.c:input_device_set_channel() idev (nil) psm 17 bluetoothd[11270]: Refusing input device connect: No such file or directory (2) bluetoothd[11270]: profiles/input/server.c:confirm_event_cb() bluetoothd[11270]: Refusing connection from A4:15:66:C1:0D:2A: unknown device bluetoothd[11270]: src/adapter.c:dev_disconnected() Device A4:15:66:C1:0D:2A disconnected, reason 3 bluetoothd[11270]: src/adapter.c:adapter_remove_connection() bluetoothd[11270]: plugins/policy.c:disconnect_cb() reason 3 bluetoothd[11270]: src/adapter.c:bonding_attempt_complete() hci0 bdaddr A4:15:66:C1:0D:2A type 0 status 0xe bluetoothd[11270]: src/device.c:device_bonding_complete() bonding (nil) status 0x0e bluetoothd[11270]: src/device.c:device_bonding_failed() status 14 bluetoothd[11270]: src/adapter.c:resume_discovery() So I don't know what is happening here and a bit of help would be appreciated.

  Read the article

• Windows 7 restarts PC when selected from GRUB Menu

  - by Dan Still

  I installed windows 7 on a RAID 5 (2@160GB SATA +1@160GB SATA for RAID 5) I then proceeded to install Ubuntu 11.10 using the Live CD and opted: "Install along side Windows 7 Option" Upon boot GRUB appears normally and I can select and run Ubuntu with no difficulties. When I select Windows 7 from GRUB the PC restarts and consequently goes back to GRUB. I have attempted to use the Windows 7 DVD to repair the installation but to no avail. The Wizard ran twice as it described it might, after the second attempt came back with an '...inability to repair...' error. I am sure there is an answer to this somewhere but I have yet to be able to find it. (2 weeks and countless attempts and searches before posting this question. Although I am happy to use Ubuntu alone my wife likes to watch Netflix and therein requires the Windows 7 installation. Any answers are appreciated and welcomed. Thanks in advance. Dan Still

  Read the article

• Is it possible to get dragging work on a Macbook multi-touch touch pad

  - by lhahne

  I have a Macbook 5,1. That is to say that it is the only 13 inch aluminium Macbook as the later revisions were renamed Macbook Pro. Two-finger scrolling seems to work fine but dragging doesn't work. In OsX this works so that you point an object, click and keep your finger pressed on the touch pad while slide another finger to move the cursor. This causes weird and undefined behavior in Ubuntu as it seems the driver doesn't recognize this as dragging. Any ideas?

  Read the article

• EHome IR receiver and Ubuntu 13 - any one have this working?

  - by squakie

  I have a "generic" USB IR receiver I purchased off of Ebay to make my life a little easier with XBMC on my Ubuntu box. I am currently running 13.10 and have never tried nor have any knowledge of IR in Ubuntu. I know of lirc, and I know a lot of it is now included in the kernel. My understanding is that lirc in basic terms maps pulses from an remote control to functions - like keyboard or mouse clicks. It is also my understanding that I might still need a driver or something for my device. lsusb shows the device as: Bus 006 Device 003: ID 147a:e016 Formosa Industrial Computing, Inc. eHome Infrared Receiver dmesg shows the following pertaining to the device: [43635.311985] usb 6-2: USB disconnect, device number 2 [43641.344387] usb 6-2: new full-speed USB device number 3 using ohci-pci [43641.543454] usb 6-2: New USB device found, idVendor=147a, idProduct=e016 [43641.543467] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [43641.543473] usb 6-2: Product: eHome Infrared Transceiver [43641.543478] usb 6-2: Manufacturer: Formosa21 [43641.543483] usb 6-2: SerialNumber: FM000623 [43641.555736] Registered IR keymap rc-rc6-mce [43641.555968] input: Media Center Ed. eHome Infrared Remote Transceiver (147a:e016) as /devices/pci0000:00/0000:00:12.0/usb6/6-2/6-2:1.0/rc/rc2/input15 [43641.556221] rc2: Media Center Ed. eHome Infrared Remote Transceiver (147a:e016) as /devices/pci0000:00/0000:00:12.0/usb6/6-2/6-2:1.0/rc/rc2 [43641.556584] input: MCE IR Keyboard/Mouse (mceusb) as /devices/virtual/input/input16 [43641.557186] rc rc2: lirc_dev: driver ir-lirc-codec (mceusb) registered at minor = 0 [43641.731965] mceusb 6-2:1.0: Registered Formosa21 eHome Infrared Transceiver with mce emulator interface version 1 [43641.731978] mceusb 6-2:1.0: 2 tx ports (0x0 cabled) and 2 rx sensors (0x0 active) (excuse the double spacing, but I had to put in extra cr/lf using "enter" or the entire thing was just one long unreadable string). When I connect the same IR receiver to a Raspberry Pi running OpenELEC/XBMC there is no flashing led unless I press a remote button, and the device works. In Ubuntu, the led is constantly blinking, and nothing happens when I press a remote key. I tried the command line program to test but it never echoes anything back to the terminal window. I believe it must need some sort of driver or something else, but I am completely in the dark on this. If it matters I also have: - Logitech wireless keyboard/mouse USB receiver - Tenda USB wireless adapter And.....I've also noticed some errors now that show in dmesg that seem to somehow related to HDMI if that makes any sense: 46721.144731] HDMI: ELD buf size is 0, force 128 [46721.144749] HDMI: invalid ELD data byte 0 [46721.444025] HDMI: ELD buf size is 0, force 128 [46721.444061] HDMI: invalid ELD data byte 0 [46721.743375] HDMI: ELD buf size is 0, force 128 [46721.743411] HDMI: invalid ELD data byte 0 [46722.043092] HDMI: ELD buf size is 0, force 128 [46722.043118] HDMI: invalid ELD data byte 0 [46722.343086] HDMI: ELD buf size is 0, force 128 [46722.343122] HDMI: invalid ELD data byte 0 [46722.642517] HDMI: ELD buf size is 0, force 128 [46722.642574] HDMI: invalid ELD data byte 0 [46722.942459] HDMI: ELD buf size is 0, force 128 [46722.942485] HDMI: invalid ELD data byte 0 [46723.242103] HDMI: ELD buf size is 0, force 128 [46723.242129] HDMI: invalid ELD data byte 0 [46723.541877] HDMI: ELD buf size is 0, force 128 [46723.541923] HDMI: invalid ELD data byte 0 [58366.651954] HDMI: ELD buf size is 0, force 128 [58366.651980] HDMI: invalid ELD data byte 0 [58366.951523] HDMI: ELD buf size is 0, force 128 [58366.951549] HDMI: invalid ELD data byte 0 [58367.251075] HDMI: ELD buf size is 0, force 128 [58367.251121] HDMI: invalid ELD data byte 0 [58367.550517] HDMI: ELD buf size is 0, force 128 [58367.550563] HDMI: invalid ELD data byte 0 [58367.850219] HDMI: ELD buf size is 0, force 128 [58367.850256] HDMI: invalid ELD data byte 0 [58368.150160] HDMI: ELD buf size is 0, force 128 [58368.150185] HDMI: invalid ELD data byte 0 [58368.449544] HDMI: ELD buf size is 0, force 128 [58368.449570] HDMI: invalid ELD data byte 0 [58368.749583] HDMI: ELD buf size is 0, force 128 [58368.749629] HDMI: invalid ELD data byte 0 [58369.049280] HDMI: ELD buf size is 0, force 128 [58369.049326] HDMI: invalid ELD data byte 0 [58394.706273] HDMI: ELD buf size is 0, force 128 [58394.706300] HDMI: invalid ELD data byte 0 [58394.706350] HDMI: ELD buf size is 0, force 128 [58394.706367] HDMI: invalid ELD data byte 0 [58395.003032] HDMI: ELD buf size is 0, force 128 [58395.003058] HDMI: invalid ELD data byte 0 [58395.302680] HDMI: ELD buf size is 0, force 128 [58395.302705] HDMI: invalid ELD data byte 0 [58395.602442] HDMI: ELD buf size is 0, force 128 [58395.602477] HDMI: invalid ELD data byte 0 [58395.902143] HDMI: ELD buf size is 0, force 128 [58395.902179] HDMI: invalid ELD data byte 0 [58396.201839] HDMI: ELD buf size is 0, force 128 [58396.201875] HDMI: invalid ELD data byte 0 [58396.501538] HDMI: ELD buf size is 0, force 128 [58396.501574] HDMI: invalid ELD data byte 0 [58396.801232] HDMI: ELD buf size is 0, force 128 [58396.801268] HDMI: invalid ELD data byte 0 [58397.100583] HDMI: ELD buf size is 0, force 128 [58397.100627] HDMI: invalid ELD data byte 0 [63095.766042] systemd-hostnamed[8875]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname! dave@davepc:~$ EDIT: Maybe another way to look at this would be what does Ubuntu do or not do that OpenELEC does or doesn't do (on Raspberry Pi) such that it works in OpenELEC but not in Ubuntu?

  Read the article

• How to Configure OpenLDAP on Ubuntu 10.04 Server

  - by user3215

  I am following the Ubuntu server guide to configure OpenLDAP on an Ubuntu 10.04 server, but can not get it to work. When I try to use sudo ldapadd -x -D cn=admin,dc=don,dc=com -W -f frontend.ldif I'm getting the following error: Enter LDAP Password: <entered 'secret' as password> adding new entry "dc=don,dc=com" ldap_add: Naming violation (64) additional info: value of single-valued naming attribute 'dc' conflicts with value present in entry Again when I try to do the same, I'm getting the following error: root@avy-desktop:/home/avy# sudo ldapadd -x -D cn=admin,dc=don,dc=com -W -f frontend.ldif Enter LDAP Password: ldap_bind: Invalid credentials (49) Here is the backend.ldif file: # Load dynamic backend modules dn: cn=module,cn=config objectClass: olcModuleList cn: module olcModulepath: /usr/lib/ldap olcModuleload: back_hdb # Database settings dn: olcDatabase=hdb,cn=config objectClass: olcDatabaseConfig objectClass: olcHdbConfig olcDatabase: {1}hdb olcSuffix: dc=don,dc=com olcDbDirectory: /var/lib/ldap olcRootDN: cn=admin,dc=don,dc=com olcRootPW: secret olcDbConfig: set_cachesize 0 2097152 0 olcDbConfig: set_lk_max_objects 1500 olcDbConfig: set_lk_max_locks 1500 olcDbConfig: set_lk_max_lockers 1500 olcDbIndex: objectClass eq olcLastMod: TRUE olcDbCheckpoint: 512 30 olcAccess: to attrs=userPassword by dn="cn=admin,dc=don,dc=com" write by anonymous auth by self write by * none olcAccess: to attrs=shadowLastChange by self write by * read olcAccess: to dn.base="" by * read olcAccess: to * by dn="cn=admin,dc=don,dc=com" write by * read frontend.ldif file: # Create top-level object in domain dn: dc=don,dc=com objectClass: top objectClass: dcObject objectclass: organization o: Example Organization dc: Example description: LDAP Example # Admin user. dn: cn=admin,dc=don,dc=com objectClass: simpleSecurityObject objectClass: organizationalRole cn: admin description: LDAP administrator userPassword: secret dn: ou=people,dc=don,dc=com objectClass: organizationalUnit ou: people dn: ou=groups,dc=don,dc=com objectClass: organizationalUnit ou: groups dn: uid=john,ou=people,dc=don,dc=com objectClass: inetOrgPerson objectClass: posixAccount objectClass: shadowAccount uid: john sn: Doe givenName: John cn: John Doe displayName: John Doe uidNumber: 1000 gidNumber: 10000 userPassword: password gecos: John Doe loginShell: /bin/bash homeDirectory: /home/john shadowExpire: -1 shadowFlag: 0 shadowWarning: 7 shadowMin: 8 shadowMax: 999999 shadowLastChange: 10877 mail: [email protected] postalCode: 31000 l: Toulouse o: Example mobile: +33 (0)6 xx xx xx xx homePhone: +33 (0)5 xx xx xx xx title: System Administrator postalAddress: initials: JD dn: cn=example,ou=groups,dc=don,dc=com objectClass: posixGroup cn: example gidNumber: 10000 Can anyone help me?

  Read the article

• Installing pgAdmin III for postgreSQL 9.2

  - by Mikey

  I have a windows server that runs postgresql 9.2. I want to hit it using pgAdmin III from my Ubuntu Linux 12.10 workstation box. I installed pgAdmin III from synaptic and also tried direct download from postgreSQL site using software installer. Regardlesss, I can get only get pgAdmin III for postgresql 9.1. When I run pgAdmin III and point to my server I get an error message telling me that the database is 9.2 and my pgAdmin III is for 9.1, isn't compatible with 9.2. I can access the server itself fine OK from the Ubuntu box - I have Python programs that hit the database with no problems - but I need pgAdmin III for 9.2 running under Ununtu Linux 12.10. Is it available? Where do I get it?

  Read the article

• Ubuntu doesn't let me to blacklist modules

  - by László Monda

  I'd like to blacklist a couple of modules, namely drm, drm_kms_helper, i2c_algo_bit and i915 to not allow my integrated Intel GPU to ever be used, but instead my Nvidia MXM card. I inserted the following lines into /etc/modprobe.d/blacklist.conf: blacklist i915 blacklist drm blacklist drm_kms_helper blacklist i2c_algo_bit Despite the above right after rebooting my laptop and typing lsmod I can see these modules loaded. Why does my blacklist get utterly disrespected and what can I do about it?

  Read the article

• How can I run sudo gedit as gksu gedit

  - by SimplySimon

  I'm looking into ways of automatically loading Gedit as gksu gedit when I enter sudo gedit by mistake? I have found that I have made a number of files unreachable by using gedit and I have only just found out why! ACHIEVED SO FAR I have written a script which will make an alias so that if I type in sudo <application> it can automatically convert that to gksu <application> but I want to make this alias stick, so that I don't have to run the script every time I boot the computer. Is there a config file I can edit or should I run this script as a start up script (which would be inconvenient!)?

  Read the article

• I cant add PPA repositories!

  - by Karthik Krishna

  For example, after running this command : sudo add-apt-repository ppa:tualatrix/ppa I get the following output : Traceback (most recent call last): File "/usr/bin/add-apt-repository", line 125, in <module> ppa_info = get_ppa_info_from_lp(user, ppa_name) File "/usr/lib/python2.7/dist-packages/softwareproperties/ppa.py", line 80, in get_ppa_info_from_lp curl.perform() pycurl.error: (6, "Couldn't resolve host 'launchpad.net'") Why is it so. I just installed Ubuntu 12.04 LTS. And it works fine. I have updated and installed the system. I have even installed all required packages. But the thing is as soon as I want to install more packages, Like PPA and sort I am not able to. Till now I have not been able to install any PPA. I am working behind a proxy.

  Read the article

• Both 12.10&12.04 Installation freeze

  - by Fih

  A friend of mine is having problems installing Ubuntu. We've tried both 12.10 and 12.04 ver. but each time we get http://img513.imageshack.us/img513/6332/27456089.png and then we got stuck. His comp is: Motherboard: ASUS P5G41-M LX CPU: Pentium(R) Dual-Core CPU E6500 @ 2.93GHz DISK: Disk 500.1 GB SAMSUNG HD502HJ RAM: Slot 1 DDR2 (PC2-6400) 2048 MB Kingston Slot 2 DDR2 (PC2-6400) 2048 MB Hyundai Electronics Graph card: NVIDIA GeForce GT 240 Any solution to this? Bests, Dwig

  Read the article

• How to setup Thinkpad features on Thinkpad T500

  - by gijoemike

  I have a IBM-Lenovo Thinkpad T500. I was previously a exclusive windows user, but recently installed ubuntu and loving it because of speed and interface. The only thing is that I don't get some features that I came to enjoy in windows. I need help setting these up: Hard-drive protection - active protection software that pauses drive when there is movement My printer doesn't work (can't find the driver for this one): canon Ip2600 A way to change which graphics chip to use while in OS. I have both the integrated and non integrated (dual-graphics). (If not easy to setup, I know there's a way to do it before it boots, but don't know how). CPU performance level - in windows you can pick "high performance", "power saver", etc.. to save batteries. My integrated camera w/light - it works but need an app where I can record videos, take snapshots, etc. can't find one that works. Thanks!

  Read the article

• Non-standard installation (installing Linux from Linux)

  - by Evan Plaice

  So, here's my setup. I have one partition with the newest version installed, a second partition with an older version installed (as a backup just in case), a swap partition that both share, and a boot partition so the bootloader doesn't need to be setup after each upgrade. Partitions: sda1 ext3 /boot sda2 ext4 / (current version) sda3 ext4 / (old version) sda4 swap /swap sda5 ntfs (contains folders symbolically linked to /home on /) So far it has been a very good setup. I can create new boot loaders without screwing it up and adding my personal files into a new install is as simple as creating some symbolic links (the partition is NTFS in case I need to load windows on the system again). Here's the issue. I'd like to be able to drop the install into /distro on the current version and install a new version on / on the old version effectively replacing/upgrading it. The goal is to be able to just swap out new versions as they are released while maintaining redundancy in case I don't like th update. So far I have: downloaded the install.iso created a folder in /distro copied the install.iso into /distro extracted vmlinuz and initrd.lz into /distro Then I modified /boot/grub/menu.lst with the following entry: title Install Linux root (hd0,1) kernel /distro/vmlinuz initrd /distro/initrd.lz vmlinuz loads perfectly but it says it can't find initrd.lz on boot. I have also tried to uncompress the image with: unlzma < initrd.lz > initrd.img And, updating the menu.lst file to match; but that doesn't work either. I'm assuming that vmlinuz (linux kernel) loads, fires up the virtual filesystem by creating a ramdisk (initrd), mounts the iso, and launches the installer. Am I missing something here? Update: First, I wanted to say that the accepted answer would have been the best option if I was doing a normal Ubuntu install. Unfortunately, I was installing Linux Mint (which lacks the script needed to make debootstrap work. So the problem I with the above approach was, I was missing the command that vmlinuz (linux kernel) needed to execute to start boot into LiveCD mode. By looking in the /boot/grub/grub.cfg file I found what I was missing. Although this method will work, it requires that the installation files reside on their own partition. I took the easy route and used unetbootin to drop the LiveCD on a usb drive and booted from that. Like I said before. Debootstrap would have been the ideal solution here. Even though I couldn't use it I wrote down the steps it would've taken to use it. Step One: Format sda3 (the partition with the old copy of linux that's being overwritten) I used gparted to format it as ext4 from within the current linux install. How this is done varies based on what tools you prefer to use. Step Two: Mount the newly formatted partition (we'll call the mount ubuntu for simplicity) sudo mkdir /mnt/ubuntu sudo mount -o -loop /dev/sda3 /mnt/ubuntu Step Three: Get debootstrap sudo apt-get install debootstrap Step Four: Mount the install disk (replace ubuntu.iso with the name if your install disk) sudo mkdir /media/cdrom sudo mount -o loop ~/ubuntu.iso /media/cdrom Step Five: Install the OS using debootstrap (replace fiesty with the version you're installing and amd64 with your processor's architecture) sudo debootstrap --arch amd64 fiesty /mnt/ubuntu file:/media/cdrom The settings here varies. While I loaded debootstrap using an install iso, you can also have debootstrap automatically download and install if with a repository link (While most of these repositories contain debian versions I'm still not clear as to whether Ubuntu has similar repositories). Here a list of the debian package repositories and their mirrors. This is how you'd deploy debootstrap if you were doing it directly from a repository: sudo debootstrap --arch amd64 squeeze /mnt/debian http://ftp.us.debian.org/debian Here's the link that I primarily used to figure this out.

  Read the article

• kubuntu muon package manager stop working

  - by aseed

  i have kubuntu today after updating the muon package manager stuck at 64% so i closes it. and after that when i try to update or reinstall or install software the manger stuck. so how can i reinstall the muon package manger from terminal?? i try sudo apt-get install muon and i get this messege Reading package lists... Done Building dependency tree Reading state information... Done muon is already the newest version. You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: libopencv-dev : Depends: libopencv-core-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-ml-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-imgproc-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-video-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-objdetect-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-gpu-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-highgui-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-calib3d-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-flann-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-features2d-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-legacy-dev (= 2.3.1-4ppa1) but it is not going to be installed Depends: libopencv-contrib-dev (= 2.3.1-4ppa1) but it is not going to be installed E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). so what to do, i need to reinstall it because it not working ~$ sudo dpkg --configure -a dpkg: dependency problems prevent configuration of libopencv-dev: libopencv-dev depends on libopencv-core-dev (= 2.3.1-4ppa1); however: Package libopencv-core-dev is not installed. libopencv-dev depends on libopencv-ml-dev (= 2.3.1-4ppa1); however: Package libopencv-ml-dev is not installed. libopencv-dev depends on libopencv-imgproc-dev (= 2.3.1-4ppa1); however: Package libopencv-imgproc-dev is not installed. libopencv-dev depends on libopencv-video-dev (= 2.3.1-4ppa1); however: Package libopencv-video-dev is not installed. libopencv-dev depends on libopencv-objdetect-dev (= 2.3.1-4ppa1); however: Package libopencv-objdetect-dev is not installed. libopencv-dev depends on libopencv-gpu-dev (= 2.3.1-4ppa1); however: Package libopencv-gpu-dev is not installed. libopencv-dev depends on libopencv-highgui-dev (= 2.3.1-4ppa1); however: Package libopencv-highgui-dev is not installed. libopencv-dev depends on libopencv-calib3d-dev (= 2.3.1-4ppa1); however: Package libopencv-calib3d-dev is not installed. libopencv-dev depends on libopencv-flann-dev (= 2.3.1-4ppa1); however: Package libopencv-flann-dev is not installed. libopencv-dev depends on libopencv-features2d-dev (= 2.3.1-4ppa1); however: Package libopencv-features2d-dev is not installed. libopencv-dev depends on libopencv-legacy-dev (= 2.3.1-4ppa1); however: Package libopencv-legacy-dev is not installed. libopencv-dev depends on libopencv-contrib-dev (= 2.3.1-4ppa1); however: Package libopencv-contrib-dev is not installed. dpkg: error processing libopencv-dev (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: libopencv-dev sudo apt-get install -f sudo dpkg --configure -a and still same problem... and i think getting this problem because of updating kubuntu today

  Read the article

• Low disk space: home/user folder occupies 94GB

  - by tedtoy

  I am low on disk space and when I check the Disk Usage analyzer (using gksudo baobab) it indicates that my home/teddy folder is using 94GB, but when I browse through its contents I can only account for about 1gb of that usage. I've tried sudo apt-get clean and deleting the cached package files from Synaptic Package Manager, emptied trash but that has not changed the amount of free space I have. It seems similar to this problem But using the root disk usage analyzer has not given any insight into what is consuming so much space. Any ideas?

  Read the article

• How do I get vmbuilder to progress?

  - by Avery Chan

  I've used the following command to create my vm: vmbuilder kvm ubuntu --verbose --suite=precise --flavour=virtual --arch=amd64 -o --libvirt=qemu:///system --tmpfs=- --ip=192.168.2.1 --part=/home/shared/vm1/vmbuilder.partition --templates=/home/shared/vm1/templates --user=vadmin --name=VM-Administrator --pass=vpass --addpkg=vim-nox --addpkg=unattended-upgrades --addpkg=acpid --firstboot=/home/shared/vm1/boot.sh --mem=256 --hostname=chameleon --bridge=br0 I've been trying to follow the direction here. My system just outputs this and it hangs at the last line: 2012-06-26 18:08:29,225 INFO : Mounting tmpfs under /tmp/tmpJbf1dZtmpfs 2012-06-26 18:08:29,234 INFO : Calling hook: preflight_check 2012-06-26 18:08:29,243 INFO : Calling hook: set_defaults 2012-06-26 18:08:29,244 INFO : Calling hook: bootstrap How can I get vmbuilder to continue the process instead of dying right here? I'm running 12.04. EDIT: Adding some additional output details When I ^C to get out of the hang I see this: ^C2012-06-26 18:19:29,622 INFO : Unmounting tmpfs from /tmp/tmpJbf1dZtmpfs Traceback (most recent call last): File "/usr/bin/vmbuilder", line 24, in <module> cli.main() File "/usr/lib/python2.7/dist-packages/VMBuilder/contrib/cli.py", line 216, in main distro.build_chroot() File "/usr/lib/python2.7/dist-packages/VMBuilder/distro.py", line 83, in build_chroot self.call_hooks('bootstrap') File "/usr/lib/python2.7/dist-packages/VMBuilder/distro.py", line 67, in call_hooks call_hooks(self, *args, **kwargs) File "/usr/lib/python2.7/dist-packages/VMBuilder/util.py", line 165, in call_hooks getattr(context, func, log_no_such_method)(*args, **kwargs) File "/usr/lib/python2.7/dist-packages/VMBuilder/plugins/ubuntu/distro.py", line 136, in bootstrap self.suite.debootstrap() File "/usr/lib/python2.7/dist-packages/VMBuilder/plugins/ubuntu/dapper.py", line 269, in debootstrap run_cmd(*cmd, **kwargs) File "/usr/lib/python2.7/dist-packages/VMBuilder/util.py", line 113, in run_cmd fds = select.select([x.file for x in [mystdout, mystderr] if not x.closed], [], [])[0]

  Read the article

< Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >