Search Results

Search found 12829 results on 514 pages for 'hard'.

Page 137/514 | < Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >

  • Cannot boot into system after deleting partition

    - by Clayton
    Okay...so this was kind of a stupid thing for me to do now that I think back on it. I was experiencing a ton of lag and not as much memory that I could use after installing Ubuntu 12.04. So after remembering I had installed multiple server versions of Ubuntu 12.04 by mistake, I went into Disk Management and proceeded to delete each and every one. Everything went fine. Up until this week, I have not experienced any problems. But starting yesterday I began to get lag just as I had before, and nothing fixed the problem. I decided to remove the Ubuntu partition, since I was also experiencing a visual error when given the option to select one to boot(the screen doesn't come up at all, and I recieved a monitor resolution error instead, but could still access both Windows and Ubuntu via arrow keys). After deleting the Ubuntu partition, so that I could see if running just Windows would fix the problem, I proceeded with what I was doing, installing a few programs that were not tied to my prediciment in any way. Upon rebooting my desktop, however, I recieved the following error: error: unknown filesystem. grub rescue> Hoping I could boot into Ubuntu via a pendrive and possibly backup my important files and wipe the hard drive to start fresh, I installed Ubuntu 13.04, but even that does not boot. Instead, I get this message on a terminal screen: SYSLINUX 4.06. EDD 4.06-pre1 Copyright (C) 1994-2011 H. Peter Anvin et al ERROR: No configuration file found No DEFAULT or UI configuration directive found! boot: So more or less, my desktop is screwed. I need to be able to get to the files inside because of my job as an artist, as well as retrieve my documents for my stories stored on Windows. Once I can succeed in solving this once and for all, I know for a fact I will stick to Ubuntu only, and install what is required to be able to run any Windows applications I used to use or need to use. I would rather not reformat the hard drive, and if I need to, it is a last resort. And I doubt I can use a Windows Recovery Disk to get my files back, as my mom has thrown out a lot of the installation disks and paperwork I would need to even follow through with that. :\ Keep in mind that I am a novice/newbie when it comes to Linux, but am hoping ot become better at it as time goes by. I appreciate any help you guys can give me. This will probably be the last time I attempt to do anything that could risk the well-being of my PC. (I've also looked through various questions on the site and tested a lot of the solutions. None seem to have worked.)

    Read the article

  • Can I prevent an IDENTIFY PACKET DEVICE command to a specific device at boot?

    - by Brian Spisak
    This is related to a previous question related to installation that is now resolved. I'm opening a new question, because I still need to get my DVD drive working. Problem: Failed boot when my ASUS DRW-24B1/ST DVD drive is attached to my asmedia ASM1061. Symptom: ata8.00: exception Emask 0x52 Sact 0x0 SErr 0xffffffff action 0xe frozen ata8: SError: { blah blah } ata8.00: failed command: IDENTIFY PACKET DEVICE ata8.00: cmd blah blah res blah blah (ATA bus error) ata8.00: status: { DRDY } ata8: hard resetting link Background: The ASM1061 is a PCIe to SATA bridge providing 2 x 6Gb/s ports and is supposed to be fully compliant to SATA specs. I just discovered in the fine print of my ASUS P8Z77-V pro motherboard that "These SATA ports are for data hard drivers only. ATAPI devices are not supported." However, I have already installed Windows 7 using this drive and I can run the Ubuntu 12.04 installer from it as well. The only time I have a problem is during Ubuntu boot when it tries an IDENTIFY PACKET DEVICE which seems to be an ATAPI command. I can't simply switch this device to another SATA port because they are already allocated to other devices. (My chipset's 2 x 6Gb/s are connected to my boot SSD and a fast HDD while the 4 x 3Gb/s ports are running a RAID 5 array.) If this can't be fixed or worked around, I suppose I'll have to go buy SATA add-in card. Blech. Thoughts: If indeed this is a device specific issue (that it doesn't support ATAPI discovery) then I can't expect - is it udev? - to work with it. But, it seems that Windows and even the Ubuntu installer work just fine. So why does udev have a problem? At the end of the day, it would be nice to have the DVD working under Ubuntu, but I can live without it. But, as this is a dual-boot machine, I can't physically disconnect it because I want it to work with Windows. (And physically disconnecting it every time I want to boot Ubuntu is NOT an option. ;-) Questions: Should this be considered a bug? My feelings are that if it works with other OS that it should probably work with Ubuntu as well. How can I work around this problem? I have a limited knowledge of linux internals, but it seems I should be able to somehow tell udev (or whatever is doing the discovery) to ignore that device. Is there a way?

    Read the article

  • Making a surface transparent from blackness of texture

    - by Dan the Man
    I am making a "halo" shader in unity using GLSL. And I've come to a roadblock. What I need to do is take a texture, like the following, and make it transparent according to the darkness of it. And I don't want a cutout, because that cuts it off at a hard edge. This line of code doesn't seem to work. gl_FragColor = texture2D( vec4( _MainTex.r, _MainTex.g, _MainTex.b, _MainTex.a), vec2(textureCoordinates));

    Read the article

  • Interesting links week #48

    - by erwin21
    Below a list of interesting links that I found this week: Interaction: 5 of the Best New User Experiences of 2010 Frontend: 10 Common Validation Errors and How To Fix Them An Introduction to jQuery Templates 10 CSS3 Properties you Need to be Familiar with Development: What is difference between HTTP Handler and HTTP Module Slash your ASP.NET compile/load time without any hard work Interested in more interesting links follow me at twitter http://twitter.com/erwingriekspoor

    Read the article

  • android third party libraries

    - by Terrance
    Its hard to believe that there aren't a ton of awesome third party (possibly open source) libraries out on the web for android using java but, I cant say I have found a great many so far but, droid seems like the only notable one I've come across. Any other majorly useful android libraries out there? Sorry in advanced if there is a dupe out there somewhere (seems like there should be) but if there is by all means post it and let me know.

    Read the article

  • Get to Know MySQL Workbench

    <b>Ghacks:</b> "Although MySQL works exceptionally well from the command line (it's not as hard as one would think), having a solid GUI tool just opens the user up to learning more powerful tasks and getting more work done faster."

    Read the article

  • Something similar to Objective-C categories in other languages?

    - by adig
    I understand Objective-C categories and how they become useful, but I always have a hard time explaining the concept to other programmers that are not familiar with Objective C. Maybe I'm just bad at explaining things, but I was thinking at another way to explain it by comparing to similar features offered by other (more popular) languages. (ex : I can explain the similarities between Objective C protocols and Java Interfaces) Any examples similar to Categories ?

    Read the article

  • How does a web browser save passwords?

    - by marcus
    How do current web browsers (or mobile mail clients and any software in general) save user passwords? All answers about storing passwords say we should store only hashes, not the password themselves. But I'm having a hard time searching the web trying to find the best techniques to store passwords when we know we will need them in plain text later on — without storing them in plain text, without using a weak encryption (known key) and without asking the user for a master password. Any ideas?

    Read the article

  • Google I/O 2010 - Moving beyond markers: Advanced Maps API customization

    Google I/O 2010 - Moving beyond markers: Advanced Maps API customization Google I/O 2010 - Moving beyond markers: Advanced Maps API customization Geo 301 Jez Fletcher, David Day With such a large number of Google Maps API sites online, it can be hard to make your site stand out from the crowd. This session covers ways in which you can enhance your Maps API application to truly differentiate it, including customizing your overlays, controls, and map. For all I/O 2010 sessions, please go to code.google.com From: GoogleDevelopers Views: 16 0 ratings Time: 36:38 More in Science & Technology

    Read the article

  • New Book! SQL Server 2012 Integration Services Design Patterns!

    - by andyleonard
    SQL Server 2012 Integration Services Design Patterns has been released! The book is done and available thanks to the hard work and dedication of a great crew: Michelle Ufford ( Blog | @sqlfool ) – co-author Jessica M. Moss ( Blog | @jessicammoss ) – co-author Tim Mitchell ( Blog | @tim_mitchell ) – co-author Matt Masson ( Blog | @mattmasson ) – co-author Donald Farmer ( Blog | @donalddotfarmer ) – foreword David Stein ( Blog | @made2mentor ) – technical editing Mark Powers – editing Jonathan Gennick...(read more)

    Read the article

  • Setting up a mail server to send mail from IP

    - by Manishearth
    I have a fixed LAN IP, but no domain name. I'd like to be able to send emails within the LAN, and receive mails sent to my IP (user needs to send an email to [email protected]). I've tried the stuff in this post -- the "easy" one gives me an IMAP error in squirrelmail (IMAP is open and listening, but not working), and the "hard" one seems to be outdated. Is it possible to set up an email server (preferably on 12.04) without having a domain name?

    Read the article

  • HighPoint RocketRAID 62x Controller

    - by TeXnewbie
    I have the subject card recently installed in Ubuntu 12.04.1 LTS (GNU/Linux 3.2.0-31-generic x86_64). See partial lspci -vv listing below (complete listing played havoc with pre tags): 03:00.0 RAID bus controller: HighPoint Technologies, Inc. Device 0622 (rev 01) Subsystem: HighPoint Technologies, Inc. Device 0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 9c00 [size=8] Region 1: I/O ports at 9800 [size=4] Region 2: I/O ports at 9400 [size=8] Region 3: I/O ports at 9000 [size=4] Region 4: I/O ports at 8c00 [size=16] Region 5: Memory at fdbff000 (32-bit, non-prefetchable) [size=2K] Expansion ROM at fdbe0000 [disabled] [size=64K] Capabilities: I followed instructions I found at https://help.ubuntu.com/community/RocketRaid to compile the drivers for it, and although performing the process described there seemed to work fine with no noticeable errors, when I rebooted after performing that procedure I could not boot. During dkms steps, I noticed messages indicating that (If next boot fails, revert to initrd.img-3.2.0-31-generic.old-dkms image) update-initramfs................ so I booted using a Ubuntu 12.10 LiveDVD and reverted to the old-dkms initrd.img as suggested above, but this failed to repair the boot problem. Ultimately, I used https://help.ubuntu.com/community/Boot-Repair in Ubuntu-Secure-Remix to fix the boot problem and was able to boot normally again, but now with the newly generated initrd.img in place again (which now boots normally), when I modprobe the rr62x kernel module, I immediately get a hard crash with messages to console about a kernel paging request that seems to have caused the problem. I've tried on multiple occasions now to use the newly built kernel module so as to allow me to use an eSATA port multiplier plugged into the card, but to no avail. Any suggestions on fixes or workarounds (I've read that some of the HighPoint cards (2720SGL) seem to work as a host bus adapter and thus may not need a custom driver, but that seems not to be the case for mine) would be most appreciated. My goal is to use the card as described here and with software RAID mdadm utilities. If necessary, I can hand-copy the console messages after the hard crash into a follow-up message, but I obviously can't do a cut/paste. I'll gladly provide any other details that are needed, but not sure what those would be at this point, so I'll refrain from adding other details for now. Thanks in advance for any help.

    Read the article

  • Smartmontools: Ya Mon!

    <b>Linux Magazine:</b> "Last article we introduced the SMART capabilities of hard drives (who knew your drives were SMART?). In this article smartmontools, an application for examining the SMART attributes and trigger self tests, is examined."

    Read the article

  • Can't format / delete locked partition from gparted?

    - by tech
    I cannot format my hard disk for ubuntu installation. It has Fedora installed in it. I wonder how to unlock the locked partition to delete and format it, since I am stucked at installing ubuntu. I am now using a livecd to do the task. No options are available for me to use. Link to screenshot: http://img822.imageshack.us/img822/7929/screenshotfrom201211151.png If you have any questions, please ask below.

    Read the article

  • Using ext4 in VMware machine

    First of all, using a journaling filesystems like NTFS, ext4, XFS, or JFS (not to name all of them) is a very good idea and nowadays unthinkable not to do. Linux offers a good variety of different option as journaling filesystem for your system. Since years I am using SGI's XFS and I am pretty confident with stability, performance and liability of the system. In earlier years I had to struggle with incompatibilities between XFS and the boot loader. Using an ext2 formatted /boot solved this issue. But, wow, that is ages ago! Lately, I had to setup a fresh Lucid Lynx (Ubuntu 10.04 LTS) system for a change of our internal groupware / messaging system. Therefore, I fired up a new virtual machine with almost standard configuration in VMware Server and run through our network-based PXE boot and installation procedure. At a certain step in this process, Ubuntu asks you about the partitioning of your hard drive(s). Honestly, I have to say that only out of curiousity I sticked to the "default" suggestion and gave my faith and trust into the Ubuntu installation routine... Resulting to have an ext4 based root mount point ( / ). The rest of the installation went on without further concerns or worries. Note:I really can't remember why I chose to go away from my favourite... Well, it should turn out to be the wrong decision after all. Ok, let's continue the story about ext4 in a VMware based virtual machine. After some hours installing additional packages and configuring the new system using LDAP for general authentication and login, I had an "out-of-the-box" usable enterprise messaging system based on Zarafa 6.40 Community Edition inclusive proper SSL-based Webaccess interface and Z-Push extension for ActiveSync with my Nokia mobile. Straightforward and pretty nice for the time spent on the setup. Having priority on other tasks I let the system just running and didn't pay any further attention at all. Until I run into an upgrade of "Mail for Exchange" on Symbian OS. My mobile did not bother me at all with the upgrade and everything went smooth, but trying to re-establish the ActiveSync connection to the Zarafa messaging system resulted in a frustating situation. So, I shifted my focus back to the Linux system and I was amazed to figure out that the root had been remounted readonly due to hard drive failures or at least ext4 reported errors. Firing up Google only confirmed my concerns and it seems that using ext4 for VMware based virtual machines does not look like a stable and reliable candidate to me. You might consider reading those external resources: ext4 fs corruption under VMWare Server 2.01Bug #389555 - ext4 filesystem corruption Well, I learned my lesson and ext{2|3|4} based filesystems are not going to be used on any of my Linux systems or customer installations in the future. Addendum: I did not try this setup in other virtualization environments like VirtualBox, qemu, kvm, Xen, etc.

    Read the article

  • How We Learn To Hold Our Keyboards [Funny]

    - by Jason Fitzpatrick
    Your environment can have a big influence on your default keyboard hold: which kind of hold do you use? We don’t know about the rest of you but we learned the cubicle-hold long before we landed in a cubicle farm. [via MakeUseOf] HTG Explains: How Windows Uses The Task Scheduler for System Tasks HTG Explains: Why Do Hard Drives Show the Wrong Capacity in Windows? Java is Insecure and Awful, It’s Time to Disable It, and Here’s How

    Read the article

  • How to effectively use an overseas SEO team?

    - by Dan Gayle
    My company is currently in contract with a 20+ person team in the Philippines, previously used for comment linking and guest blogging spun content articles. This is a practice that we're stopping, but we don't want to sever our team because they work hard, they're really cheap, and they produce excellent accounting and reporting of their actions. What are ways that we can best put them to use as a link generating or content generating resource? Their English is fair, but not of high enough quality to use them for any direct content creation. Thanks

    Read the article

  • Achieving a Strong SEO Rating

    SEO or Search Engine Optimization is a must if you are serious in having your website placed with the search engine, and with great results. There are important guidelines to be followed. It is really not that hard to understand even for beginners. For beginners the term optimization may sound somewhat difficult, when actually it is very doable.

    Read the article

  • Week in Geek: Google Drive Desktop Client Allows Backdoor Access to Google Accounts

    - by Asian Angel
    Our last edition of WIG for October is filled with news link coverage on topics such as Microsoft may not issue a second Windows 7 service pack, Windows Media Center is free for Windows 8 Pro users for limited time, CyanogenMod logged swipe gestures used to unlock Android devices, and more. What Is the Purpose of the “Do Not Cover This Hole” Hole on Hard Drives? How To Log Into The Desktop, Add a Start Menu, and Disable Hot Corners in Windows 8 HTG Explains: Why You Shouldn’t Use a Task Killer On Android

    Read the article

  • Howto: Migrate off wubi

    - by schwiz
    I recently installed Ubuntu through Wubi and I love it enough I am ready to ditch windows! My set up is like this. Drive 1: 80 gig ssd Win7 Drive 2: 320 gig hdd Ubuntu (installed through wubi) Drive 3: 1000 TB NTFS media drive What I want to do is move the Ubuntu install from the 320 gig hard drive to my ssd and totally get rid of Windows. Would be great if I could preserve my current Ubuntu install during the process since its finally working :-) Thanks! Nathan

    Read the article

  • When to skip solving the general problem and settling for the specific problem?

    - by Peter Smith
    I've been working hard on trying to develop a general solution to my problem, but I cannot seem to formulate a proper algorithm for it, at least one that doesn't take a ton of inaccurate grunt work building a lookup table. I have a solution already for the specific requirement, but it requires the software's configuration to be changed every time the software is loaded with a different geographic area's datasets. So is it better to be finished and move on for now, or to keep attempting to solve the general problem knowing that the specific problems will keep popping up?

    Read the article

  • Data Structures for Logic Games / Deduction Rules / Sufficient Set of Clues?

    - by taserian
    I've been cogitating about developing a logic game similar to Einstein's Puzzle , which would have different sets of clues for every new game replay. What data structures would you use to handle the different entities (pets, colors of houses, nationalities, etc.), deduction rules, etc. to guarantee that the clues you provide point to a unique solution? I'm having a hard time thinking about how to get the deduction rules to play along with the possible clues; any insight would be appreciated.

    Read the article

< Previous Page | 133 134 135 136 137 138 139 140 141 142 143 144  | Next Page >