Search Results

Search found 4296 results on 172 pages for 'serial ports'.

Page 138/172 | < Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >

  • Ubuntu 10.04 and fedora 14 grub conflict

    - by sawren
    I tried to triple boot Windows xp, Fedora 14 and Ubuntu 10.04. I first installed Windows xp, then fedora followed by Ubuntu. The problem is that i don't get option to boot Ubuntu while Xp boots fine. It seems Ubuntu was unable to replace Fedora's grub with its own at MBR. Looking at their grub conf file, Fedora and Ubuntu identifies same harddisk as two different devices and i do have another 80 GB harddisk which doesn't have any OS. Below is the details on my partitions and partial information from grub files of both OS. Device Boot Start End Blocks Id System /dev/sda1 * 63 40965749 20482843+ 7 HPFS/NTFS /dev/sda2 102414436 312576704 105081134+ f W95 Ext'd (LBA) /dev/sda3 40965750 102414374 30724312+ 83 Linux - /Home (for fedora) /dev/sda5 102414438 204812684 51199123+ 7 HPFS/NTFS /dev/sda6 204812748 253634219 24410736 83 Linux -- ubuntu /dev/sda7 253634283 302455754 24410736 83 Linux -- fedora /dev/sda8 302455818 312576704 5060443+ 82 Linux swap / Solaris grub.cfg from ubuntu ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-21-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd1,7)' search --no-floppy --fs-uuid --set cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 linux /boot/vmlinuz-2.6.32-21-generic root=UUID=cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 ro quiet splash initrd /boot/initrd.img-2.6.32-21-generic } menuentry 'Ubuntu, with Linux 2.6.32-21-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod ext2 set root='(hd1,7)' search --no-floppy --fs-uuid --set cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 echo 'Loading Linux 2.6.32-21-generic ...' linux /boot/vmlinuz-2.6.32-21-generic root=UUID=cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 ro single echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-21-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod ext2 set root='(hd1,7)' search --no-floppy --fs-uuid --set cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod ext2 set root='(hd1,7)' search --no-floppy --fs-uuid --set cd55e078-a2c1-4d8a-9e87-ae838b6f4a05 linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Microsoft Windows XP Professional (on /dev/sdb1)" { insmod ntfs set root='(hd1,1)' search --no-floppy --fs-uuid --set cad48cc6d48cb5eb drivemap -s (hd0) ${root} chainloader +1 } menuentry "Fedora (2.6.35.14-96.fc14.i686) (on /dev/sdb6)" { insmod ext2 set root='(hd1,6)' search --no-floppy --fs-uuid --set 6aee34cf-f77a-489a-9361-85d07194b84b linux /boot/vmlinuz-2.6.35.14-96.fc14.i686 ro root=UUID=6aee34cf-f77a-489a-9361-85d07194b84b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /boot/initramfs-2.6.35.14-96.fc14.i686.img } menuentry "Fedora (2.6.35.6-45.fc14.i686) (on /dev/sdb6)" { insmod ext2 set root='(hd1,6)' search --no-floppy --fs-uuid --set 6aee34cf-f77a-489a-9361-85d07194b84b linux /boot/vmlinuz-2.6.35.6-45.fc14.i686 ro root=UUID=6aee34cf-f77a-489a-9361-85d07194b84b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /boot/initramfs-2.6.35.6-45.fc14.i686.img } ### END /etc/grub.d/30_os-prober ### grub.conf from fedora default=0 timeout=5 splashimage=(hd0,5)/boot/grub/splash.xpm.gz hiddenmenu title Fedora (2.6.35.14-96.fc14.i686) root (hd0,5) kernel /boot/vmlinuz-2.6.35.14-96.fc14.i686 ro root=UUID=6aee34cf-f77a-489a-9361-85d07194b84b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /boot/initramfs-2.6.35.14-96.fc14.i686.img title Fedora (2.6.35.6-45.fc14.i686) root (hd0,5) kernel /boot/vmlinuz-2.6.35.6-45.fc14.i686 ro root=UUID=6aee34cf-f77a-489a-9361-85d07194b84b rd_NO_LUKS rd_NO_LVM rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet initrd /boot/initramfs-2.6.35.6-45.fc14.i686.img title Other rootnoverify (hd0,0) chainloader +1

    Read the article

  • Can Current Backflow from Powered Hub's Adapter & cause PC Damage?

    - by SuperUserMan
    Getting this short: Can current flow from a powered USB hub's power adapter (lying 10 Meter away) back to computer via usb port and cause damage to Computer components like mobo, etc? What should be my concerns? Using a 2 Amp 5V Power adapter to power a 10m Long Active Repeater USB extension cable with 4 port HUB & plugging into PC's Front port, causes PC Chassis fan to keep running (thought slower than regular speed) Front Chassis HDD & power LED to turn on (though bit dim) may be other things which i cant detect/see at chip level, in motherboard?? All this even after PC is shut down (bit scary) More detail (in case still want to read): To run 4 High power (needing 450 mAmps) Wifi Adapters, far away from PC, Bought Active Repeater USB Extension Cable with 4 Ports & power port at far end http://www.ebay.com/itm/33FT-USB-2-0-Male-to-Female-Extension-Cable-Hub-Splitter-Adapter-with-4-USB-Port-/390846115254 Then added a locally bought 2 Amp 240V AC to 5V DC Power Adapter and plugged into USB hub which is a part of & situated at far end of a 10 Meter Active Repeater usb extension cable. Even 4 Wifi Adapters run fine (appear to) using this setup, but running chassis fan, dimly lighted Power & HDD LED, even when PC is switched off is bit scary and surely mean 5V & some current is flowing all though that 10 meter extension cable into my USB port & powering stuff. Can this cause damage? and what should be my concerns. Of course I can't switch off the power adapter (lying 10 meters away from PC) every time I switch off my PC to prevent this.

    Read the article

  • Server 2012, Jumbo Frames - should I expect problems?

    - by TomTom
    Ok, this sound might stupid - but is there any negative on just enabling jumbo frames in practice? From what I understand: Any switch or ethernet adapter that sees a jumbo frame it can not handle will just drop it. TCP is not a problem as max frame size is negotiated in the setinuo phase. UCP is a theoretical problem as a server may just send a LARGE UDP packet that gets dropped on the way. Practically though, as UDP is packet based, I do not really think any software WOULD send a UDP packet larger than 1500 bytes net without app level configuration changes - at least this is how I do my programming, as it is quite hard to get a decent MTU size for that without testing yourself, so you fall back in programming to max 1500 packets. The network in question is a standard small business network - we upgraded now from a non managed 24 port switch to a 52 port switch with 4 10g ports (netgear - quite cheap) and will mov a file server to 10g for also ISCSI serving. All my equipment on the Ethernet level can handle minimum 9000 bytes and due to local firewalls I really want to get packets larger (less firewall processing), but the network is also NAT'ed to the internet. On top, different machines move around (download) large files (multi gigabyte area) quite often for processing. The question is - can I expect problems when I just enable jumbo frames? Again, this is not totally ignorance - I just don't see programs sending more than 1500 byte UDP packets (if that is a practical problem please tell me) and for TCP the MTU is negotiated anyway. if there is a problem I can move to a dedicated VLAN, but this has it's own shares of problems as basically most workstations must then be on both VLAN's.

    Read the article

  • USB Device Not Recognized

    - by Franky Chanyau
    Ok this one gets a little bit complicated but bare with me :D A client brought her computer in to be fixed about a week ago, she says she tried charging a new phone she bought from china and immediately after her usb keyboard and mouse stopped working (typical). I had a quick look at it but because I did not have time, I did a simple system restore and it seemed as if the issue was fixed. I promptly sent it back to her but a few days back she called saying that the issue has returned. Turns out the computer was riddled with some virus that also corrupted her XP install so I had to format the whole thing(yes I tried repairing). I hoped that the format would fix the keyboard and mouse issue but the whole thing has escalated and the computer will throw the "USB Device not recognized" error when I plug anything into the many usb ports it has. I have installed all the drivers (including the chip set drivers) for the pc and even tried the unplugging from the power for a while trick, still no luck. I am sure it is not a hardware issue, but may be wrong. This is way over my head. Can anyone help? Computer: HP Compaq DC7100, Intel Pentium 4, 512mb RAM OS: Windows XP Professional SP2

    Read the article

  • Pros and Cons of a proxy/gateway server

    - by Curtis
    I'm working with a web app that uses two machines, a BSD server and a Windows 2000 server. When someone goes to our website, they are connected to the BSD server which, using Apache's proxy module, relays the requests & responses between them and the web server on the Windows server. The idea (designed and deployed about 9 years ago) was that it was more secure to have the BSD server as what outside people connected to than the Windows server running the web app. The BSD server is a bare bones install with all unnecessary services & applications removed. These servers are about to be replaced and the big question is, is a cut-down, barebones server necessary for security in this setup. From my research online I don’t see anyone else running a setup like this (I don't see anyone questioning it at least.) If they have a server between the user and the web app server(s), it is caching, compressing, and/or load balancing. Is there anything I’m overlooking by letting people connect directly from the internet ** to a Windows 2008 R2 server that’s running the web application? ** there’s a good hardware firewall between the internet with only minimal ports open Thank you.

    Read the article

  • Using a Level 2 switch as a core switch

    - by imtech
    I have a small user base of about 20 people on at a time and spiking up to about 80 people during peak times. Most people (80+%) are connected over our Aruba managed wireless system. We have a Windows Domain. We have 3 24-Port switches all connecting back to a central 48-port switch where additional access ports, firewall, servers, and wireless controller all centrally connect back to. It's a flat network with dumb switches. I'm in the process of upgrading our infrastructure. Cisco pricing for switches is pretty high for us so I've been looking at HP Procurves which seem to be within our budget range. I want to eventually make use of 802.1x, SNMP, QoS for possible VOIP upgrades, VLAN to separate guest VLAN from authenticated users, and other more advanced features. PoE would be nice but that's probably too expensive for us. I was thinking of having our core switch be a Procurve 2610 and the rest of our switches that centrally connect to it be Procurve 2510s. A true and full blown level 3 switch is way out of our price range but a 2610 seems to be good enough for us. The 2610 does static routing which ought to be good enough for us but I'm in unfamiliar territory so I'm looking for any gotchas. Also, should all the switches be 2610s or just the core switch? Do I even need the 2610, can I just go with all 2510s? I'm new to VLANs as well so I'm not sure what it is I need but I would like an affordable infrastructure that won't need replacing 2-3 years down the line because I choose a product that was lacking.

    Read the article

  • Torrent upload ratio not updated on Synology DS212+

    - by user179271
    I have a Synology DS212+ NAS running DSM 4.2-3211 (current version). I use it for several purposes including torrent download using Download Station and a tracker that needs authentication. My problem is that my download/upload ratio isn't updated, so it constantly falls down. My NAS is behind a router, and I configured the NAT to forward ports 6890 to 6999 to the internal IP address of the NAS. Here are the Download Station settings : TCP port : 6990, Sharing ratio : 900%, Sharing time : infinite, max download speed : 0 (no limit), max upload speed : 0 (no limit), BT protocol encryption : checked, max numbers of peers allowed by torrent file : 4000, DHT : checked, with port 6889. When the DHT option is not checked, the NAS doesn't upload any files. I don't know what is this option for. Can someone help me to solve this problem ? Did I miss any step, or does it come from the NAT ? How is the authentication managed by Dowload Station ? (Sorry for my english) Thanks.

    Read the article

  • Port forwarding + shared connection with Ubuntu

    - by Joey Adams
    Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

    Read the article

  • Sony PMB causing failure to load Windows 7 Pro 64-bit normally or even Safe Mode

    - by Wesley
    After installing Sony's Picture Motion Browser on my desktop with Windows 7 Pro x64, it always goes to Startup Repair due to Windows 7 failing to start. This always happens after I try to install it. I've installed with all unnecessary programs closed and all disk drives and unnecessary usb ports empty. I don't exactly know what is causing the problem. Any ideas? My desktop is an HP m8530f. http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01469325&tmp_task=prodinfoCategory&lc=en&dlc=en&cc=us&product=3740333&lang=en Only upgrades are an HD4350 and a 500W PSU. EDIT: Windows 7 cannot start now. I'm currently running diagnostic tests from the BIOS. EDIT: Here are the problem details. Problem Signature: Problem Event Name: StartupRepairOffline Problem Signature 01: 6.1.7600.16385 Problem Signature 02: 6.1.7600.16385 Problem Signature 03: unknown Problem Signature 04: 21201022 Problem Signature 05: AutoFailover Problem Signature 06: 8 Problem Signature 07: CorruptFile OS Version: 6.1.7600.2.0.0.256.1 Local ID: 1033 CONCLUSION: So, I think Sony PMB may have caused some sort of corruption in the system files. So if you have Windows 7 and plan on installing Sony PMB, find a Vista or XP machine to install on.

    Read the article

  • "Network Error - 53" while trying to mount NFS share in Windows Server 2008 client

    - by Mike B
    CentOS | Windows 2008 I've got a CentOS 5.5 server running nfsd. On the Windows side, I'm running Windows Server 2008 R2 Enterprise. I have the "Files Services" server role enabled and both Client for NFS and Server for NFS are on. I'm able to successfully connect/mount to the CentOS NFS share from other linux systems but am experiencing errors connecting to it from Windows. When I try to connect, I get the following: C:\Users\fooadmin>mount -o anon 10.10.10.10:/share/ z: Network Error - 53 Type 'NET HELPMSG 53' for more information. (IP and share name have been changed to protect the innocent :-) ) Additional information: I've verified low-level network connectivity between the Windows client and the NFS server with telnet (to the NFS on TCP/2049) so I know the port is open. I've further confirmed that inbound and outbound firewall ports are present and enabled. I came across a Microsoft tech note that suggested changing the "Provider Order" so "NFS Network" is above other items like Microsoft Windows Network. I changed this and restarted the NFS client - no luck. I've confirmed that the share folder on the NFS server is readable/writable by all (777) I've tried other variations of the mount command like: mount 10.10.10.10:/share/ z: and mount 10.10.10.10:/share z: and mount -o anon mtype=hard \\10.10.10.10:/share * No luck. As per the command output, I tried typing NET HELPMSG 53 but that doesn't tell me much. Just "The network path was not found". I'm lost on how to proceed with troubleshooting. Any ideas?

    Read the article

  • UDP blocked by Windows XP Firewall when sending to local machine

    - by user36367
    I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: Windows XP Professional with Service Pack 3, all updated Program that sends UDP datagrams Program that receives UDP datagrams Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas?

    Read the article

  • Possible to IPSec VPN Tunnel Public IP Addresses?

    - by caleban
    A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

    Read the article

  • Bypassing SQUID on freebsd with PF

    - by epema
    I have PF+SQUID31 on FREEBSD-9.0, and I want to have some hosts(aka goodguys) to bypass the proxy, so that torrents are not logged. Also, I am not sure about transparent. It means that I dont have to configure proxy settings on the client side right? I have tried doing a redirect no rdr on $int_if inet proto {tcp,udp} from 192.168.1.233/32 to any However, no luck :( Here is a quick look of my conf files: SQUID /usr/local/etc/squid/squid.conf http_port 192.168.1.1:8080 transparent RC /etc/rc.conf: gateway_enable="YES" pf_enable="YES" pf_rules="/usr/local/etc/pf.conf" pflog_enable="YES" squid_enable="YES" I have squid31 installed from ports with SQUID_PF "Enable transparent proxying with PF" on PF /usr/loca/etc/pf.conf: int_if="re0" ext_if="bge0" localnet="{ 192.168.1.0/24 }" table <goodguys> const { "192.168.1.219", "192.168.1.233" } set block-policy drop set skip on lo0 scrub in all fragment reassemble scrub out all random-id max-mss 1440 block in on $ext_if pass out on $ext_if keep state block in on $int_if pass in on $int_if inet proto tcp from $int_if:network to $int_if port 8080 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 21 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 22 keep state pass in on $int_if inet proto udp from $int_if:network to $int_if port 53 keep state pass in on $int_if inet proto tcp from $int_if:network to any port { smtp, pop3 } keep state pass in on $int_if inet proto icmp from $int_if:network to $int_if keep state pass out on $int_if keep state What lines should I add in conf files? I am assuming that the problem is on the firewall(pf).

    Read the article

  • VirtualBox VM running web server not accessible via external IP

    - by mwigdahl
    I have a Windows 7 machine running VirtualBox with an Ubuntu guest. The guest has a Bitnami LAMP stack installed. I have the guest configured for Bridged networking, and I can access the guest web server just fine from other machines on my LAN using the guest's IP. I'm trying to configure port forwarding so that I can access the web server from outside my LAN. (The router is a 2WIRE model as I'm on ATT's UVerse). I've set up port forwarding for ports 80 and 443 to the guest's IP in a similar manner to how I had them set up for my previous, physical web server, which worked just fine. However, I cannot seem to access the new, virtual web server using my external IP on the forwarded port. I suspected Windows Firewall issues on the host, but disabling it didn't solve the issue. Anyone have advice on what I should try next? EDIT: I've now attempted disabling the firewall on the guest with sudo ufw disable -- that doesn't seem to help either. However, after checking the router's port forwarding in more detail I may see the problem. My VM is named "linux" and in the router's configuration pages it shows up inconsistently. Sometimes it reports with a valid LAN IP and other times it doesn't show up with any IP. Even when it shows the correct IP the router indicates that it is disconnected. Could this be an indication that the 2WIRE router doesn't play well with VirtualBox's bridged networking mode?

    Read the article

  • iptables rules to allow HTTP traffic to one domain only

    - by Emily
    Hi everyone, I need to configure my machine as to allow HTTP traffic to/from serverfault.com only. All other websites, services ports are not accessible. I came up with these iptables rules: #drop everything iptables -P INPUT DROP iptables -P OUTPUT DROP #Now, allow connection to website serverfault.com on port 80 iptables -A OUTPUT -p tcp -d serverfault.com --dport 80 -j ACCEPT iptables -A INPUT -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT #allow loopback iptables -I INPUT 1 -i lo -j ACCEPT It doesn't work quite well: After I drop everything, and move on to rule 3: iptables -A OUTPUT -p tcp -d serverfault.com --dport 80 -j ACCEPT I get this error: iptables v1.4.4: host/network `serverfault.com' not found Try `iptables -h' or 'iptables --help' for more information. Do you think it is related to DNS? Should I allow it as well? Or should I just put IP addresses in the rules? Do you think what I'm trying to do could be achieved with simpler rules? How? I would appreciate any help or hints on this. Thanks a lot!

    Read the article

  • SSH sometimes screws up connection when terminal overflows?

    - by SeveQ
    I've got a problem with SSH on a Debian Lenny based server (it's a vHost within a Xen environment, booted on a Xen kernel). I hope someone can help me with this. The SSH connection seems somehow getting screwed up frequently when the terminal overflows (new lines beyond the bottom of the terminal, usually forcing it to scroll). The connection gets lost but not regularly disconnected. It nearly always happens when I do the following: an existing SSH connection gets disconnected (regularly) I order putty to reestablish the connection login-prompt appears at the very bottom of the putty terminal window I enter my login-name, press the enter key I'm asked for the password, I enter it, press the enter key and BOOM! Nothing more happens. I have to reconnect again. So it is reproducable. I'm not totally sure if the connection crashes before or after I enter the password. Furthermore it also happens when there is much text to be displayed (for example when I compile something or do an ls -l on a directory with many entries). Using 'screen', however, helps to reduces the frequency of occurence but doesn't solve the problem completely. It's occurence is independent from which terminal software I use. I mostly use putty but it also happens with other clients. I certainly hope somebody can help me solving this problem. Thanks in advance! //edit: I've just made a Wireshark trace of the ssh connection and there is nothing, I repeat, nothing different between the working and the failing connection (at least aside from frame numbers, ports and times that obviously can't be equal). This leads me to the assumption that the error has to happen on the server's side.

    Read the article

  • Multi-WAN bonding across different media

    - by Tom O'Connor
    I've recently been thinking again about a product that Viprinet provide, basically they've got a pair of routers, one that lives in a datacentre, Their VPN Multichannel Hub and the on-site hardware, their VPN multichannel routers They've also got a bunch of interface cards (like HWICs) for 3G, UMTS, Ethernet, ADSL and ISDN adapters. Their main spiel seems to be bonding across different media. It's something that I'd really like to use for a couple of projects, but their pricing is really quite extreme, the hub is about 1-2k, the routers are 2-6k, and the interface modules are 200-600 each. So, what I'd like to know is, is it possible with a couple of stock Cisco routers, 28xx or 18xx series, to do something similar, and basically connect a bunch of different WAN ports, but have it all presented neatly as one channel back to the internet, with seamless (or nearly) failover if one of the WAN interfaces should fail. Basically, If i got 3x 3G to ethernet modems, and each on a different network, I'd like to be able to loadbalance/bond across all of them, without having to pay Viprinet for the privilege. Does anyone know how I'd go about configuring something for myself, based around standard protocols (or vendor specific ones), but without actually having to buy the Viprinet hardware?

    Read the article

  • [Mac OS X] Terratec Cinergy Hybrid T USB XS is not recognized anymore

    - by Gabble
    I have used Terratec Cinergy Hybrid T USB XS for years now, alongside with Elgato EyeTV software. I am a happy and completely satisfied user! Since a couple of weeks the USB sitck stopped working on my MacPro1,1 (OS version 10.6.3): EyeTV does not see any device attached, and actually, the green led on the stick stays off. 1) it is not a USB port fault: I have unplugged any other USB/Firewire device and tried with different USB ports, to no avail (any other USB devices work as expected on any port) 2) I have completely uninstalled EyeTV software, including preferences and system daemons/extensions, rebooted and reinstalled the latest EyeTV. No way. 3) reset the PRAM. Nope. 4) checked the Apple System Profiler - USB: No device attached, The MacPro does not see it at all. ============= I need to say that: a) the device worked as a charm even with the latest OS 10.6.x (so it's not a OS upgrade cause) b) I have plugged the Terratec Cinergy Hybrid T USB XS to my MacBook5,1 where EyeTV is not installed and was never installed: The green led on the stick turns on, the growl bubble pops up, and the device is perfectly recognized by the system. Apple System Profiler says (sorry, Italian language): Cinergy Hybrid T USB XS (2882): ID prodotto: 0x005e ID fornitore: 0x0ccd Versione: 1.10 Numero di serie: 061102005755 Velocità: Fino a 12 Mb/sec Produttore: TerraTec Electronic GmbH ID posizione: 0x04100000 Corrente disponibile (mA): 500 Corrente necessaria (mA): 500 At this point I am pretty sure the Terratec stick is not damaged and there is something wrong with my MacPro. I kindly ask you: Is there a way to force my MacPro recognize the USB device? What can I check? Is there something that caches USB connection that can be reset? A OS reinstall would be the very last resort for me… Thanks in advance for any help you will offer!

    Read the article

  • How do I stop panning on a monitor that supports a specific resolution?

    - by IronicMuffin
    Hi all, I've been battling this for a few days now. Any and all help is appreciated. I have a planar monitor with a native res of 1280x1024. At one point, I had used PowerStrip to override "something" and set the res to 1600x1200, and it worked great. I then installed new intel graphics drivers for my 86895g (or w/e model) video card, which screwed up whatever settings I had. If I set it to 1600x1200 this time, it would set the res correctly, but give me a 1280x1024 viewport and the screen would pan when the mouse got to the edges of the screen. Absolutely not useful. Ok, so I was limited to 1280x1024 now. W/e. Now...enter new video card with two video ports. I have two monitors now and the latest nVidia drivers. I decide to try to get dual 1600x1200 going...ended up screwing the original monitor up so much now that it's at 1280x1024, with a 1024x768 viewport and panning! Absolutely not usable now. So what I need, and I can't seem to find on any forums, is help doing one or more of the following: Clearing out all monitor/edid info out of the windows registry without corrupting the registry. Actually correctly override the EDID values and get my sweet res back. Some other way of getting back to at least dual 1280x1024 with NO panning. Note: My device manager shows 4 monitors for some reason. My registry shows entries for all sorts of monitors that have been hooked up to the machine over the years. It's making it difficult to debug. Experience with PowerStrip would be helpful. I've been mucking with Phoenix EDID designer and MonInfo as well, but I'm stumbling around in the dark with these. Windows XP SP2 nVidia GeForce 6200 nVidia drivers: v258.96 Monitor: Planar PL 1910M Thanks!

    Read the article

  • IP-dependent local port-forwarding on Linux

    - by chronos
    I have configured my server's sshd to listen on a non-standard port 42. However, at work I am behind a firewall/proxy, which only allow outgoing connections to ports 21, 22, 80 and 443. Consequently, I cannot ssh to my server from work, which is bad. I do not want to return sshd to port 22. The idea is this: on my server, locally forward port 22 to port 42 if source IP is matching the external IP of my work's network. For clarity, let us assume that my server's IP is 169.1.1.1 (on eth1), and my work external IP is 169.250.250.250. For all IPs different from 169.250.250.250, my server should respond with an expected 'connection refused', as it does for a non-listening port. I'm very new to iptables. I have briefly looked through the long iptables manual and these related / relevant questions: http://serverfault.com/questions/57872/iptables-question-forwarding-port-x-to-an-ssh-port-of-different-machine-on-the-n http://serverfault.com/questions/140622/how-can-i-port-forward-with-iptables However, those questions deal with more complicated several-host scenarios, and it is not clear to me which tables and chains I should use for local port-forwarding, and if I should have 2 rules (for "question" and "answer" packets), or only 1 rule for "question" packets. So far I have only enabled forwarding via sysctl. I will start testing solutions tomorrow, and will appreciate pointers or maybe case-specific examples for implementing my simple scenario. Is the draft solution below correct? iptables -A INPUT [-m state] [-i eth1] --source 169.250.250.250 -p tcp --destination 169.1.1.1:42 --dport 22 --state NEW,ESTABLISHED,RELATED -j ACCEPT Should I use the mangle table instead of filter? And/or FORWARD chain instead of INPUT?

    Read the article

  • LogMeIn style remote access to NAS drive

    - by Mere Development
    I've been asked to setup some remote access to a NAS drive. The NAS drive will sit on a VLAN inside a network that uses a Cisco 891 IS router as gateway. The charity have no SSL-VPN licenses for the Cisco. At present there are no open ports or services on the Cisco itself and ideally we would like to keep it that way for a while, hence the request for a LogMeIn style service that's initiated from inside. We need multiple user access, about 10 max. Using LogMeIn on a machine connected to the NAS would only provide screen sharing I believe, and no concurrent connections (could be wrong?) The end users need to be able to read and write files to the NAS from Mac's and PC's around the globe. Read-only access from Mobile devices would be a bonus but not absolutely necessary. This is for a charity, non-commercial, but they are willing to spend if necessary. Cisco config knowledge is at a minimum so if I can avoid upsetting that delicate device I'll be happy :) Anyone have any clever ideas? I can provide more information on request. Thanks, Ben

    Read the article

  • What is the best way to connect a 3 switches with a router?

    - by Carlos Morales
    Hello everyone, I'm trying to rebuild the network from my work and I was thinking what is the best way to connect three switches and a router. The router has 4 ports so I thought to connect 2 switches to the router (each switch connected with 2 cables to the router) and then connect the third switch to one of the others with two cables. So is like this, two cables from switch one to the router, two cables from switch two to the router and two cables from switch 3 to switch 1 or 2. So my questions are: Is it better to connect the router to each switch with a cable or the more cables you have the better? If I connect the switch 3 to switch 1 or 2 is it better to connect it with a cable or you get better performance with more cables. If I'm wrong and there is a better or more efficient way to connect them please let me know. The router is a Netgear RP114 (I'll upgrade it to a Sonicwall NSA 240), switch 1 is a Netgear GS748T, switch 2 is a Cisco Catalyst 2924-XL and switch 3 is a D-link DGS-1024D Thank you very much

    Read the article

  • Apache22 on FreeBSD - Starts, does not respond to requests

    - by NuclearDog
    Hey folks! I'm running Apache 2.2.17 with the peruser MPM on FreeBSD 8.2-RC1 on Amazon's EC2 (so it's XEN). It was installed from ports. My problem is that, although Apache is running, listening for, and accepting connections, it doesn't actually respond to any or show them in the log at all. If I telnet to the port it's listening on and type out an HTTP request: GET / HTTP/1.1 Host: asdfasdf And hit enter a couple of times, it just sits there... Nothing. No response requesting with a browser either. There doesn't appear to be anything helpful in the error log: [Sun Jan 09 16:56:24 2011] [warn] Init: Session Cache is not configured [hint: SSLSessionCache] [Sun Jan 09 16:56:25 2011] [notice] Digest: generating secret for digest authentication ... [Sun Jan 09 16:56:25 2011] [notice] Digest: done [Sun Jan 09 16:56:25 2011] [notice] Apache/2.2.17 (FreeBSD) mod_ssl/2.2.17 The access log stays empty: root:/var/log# wc httpd-access.log 0 0 0 httpd-access.log root:/var/log# I've tried with accf_http and accf_data both enabled and disabled, and with both the stock configuration and my customized config. I also tried uninstalling apache22-peruser-mpm and just installing straight apache22... Still no luck. I tried removing all of the LoadModule lines from httpd.conf and just re-enabled the ones that were necessary to parse the config. Ended up with only the following loaded: root:/usr/local/etc/apache22# /usr/local/sbin/apachectl -M Loaded Modules: core_module (static) mpm_peruser_module (static) http_module (static) so_module (static) authz_host_module (shared) log_config_module (shared) alias_module (shared) Syntax OK root:/usr/local/etc/apache22# Same results. Apache is definitely what's listening on port 80: root:/usr/local/etc/apache22# sockstat -4 | grep httpd root httpd 43789 3 tcp4 6 *:80 *:* root httpd 43789 4 tcp4 *:* *:* root:/usr/local/etc/apache22# And I know it's not a firewall issue as there is nothing running locally, and connecting from the local box to 127.0.0.1:80 results in the same issue. Does anyone have any idea what's going on? Why it would be doing this? I've exhausted all of my debugging expertise. :/ Thanks for any suggestions!

    Read the article

  • How can I get Windows 7 to work with two Nvidia graphics cards with different drivers?

    - by Max
    This is similar to this question, but I am using more similar cards with Windows 7. I just purchased a Zotac Nvidia GeForce 7200 GS. I have a motherboard with two PCI Express x16 slots. There is already an MSI Nvidia GeForce 8800 GTS being used as the primary card, driving two LCD monitors. I would like the Zotac to output to a TV via DVI-out. Unfortunately, when Windows detects the Zotac and installs its drivers, or I manually install them, Windows stops being able to boot up. If I remove them and re-install the MSI 8800 drivers, I can boot again, but Windows can no longer see the Zotac 7200--it shows up as a yellow triangle in Device Manager. I've read conflicting reports about this. Some people claim that Windows 7 will support multiple heterogeneous graphics card drivers, as long as they are all using the same driver API ("WDDM?"). Others say that they have to be using the exact same driver, or it won't work. Others claim that you have to use the exact same card. which is it, exactly? I know I can run the MSI 8800 in SLI if I purchase another, but I don't need that kind of power--I just need HD-out to my television. I read somewhere that running two cards in SLI precludes you from using 100% of their output ports, so I'm not sure if that's an option. I suppose I could also run two MSI 8800's without SLI, but again, that's more power than I need (and more money than I'd like to spend). Also, I don't think this exact model is even manufactured anymore. Any ideas?

    Read the article

  • python reports socket in use, netstat and others claim its not

    - by captainmish
    We have a strange socket issue with a RHES3 box: Python 2.4.1 (#1, Jul 5 2005, 19:17:11) [GCC 3.2.3 20030502 (Red Hat Linux 3.2.3-52)] Type "help", "copyright", "credits" or "license" for more information. >>> import socket >>> s = socket.socket() >>> s.bind(('localhost',12351)) Traceback (most recent call last): File "<stdin>", line 1, in ? File "<string>", line 1, in bind socket.error: (98, 'Address already in use') This seems normal, lets see what has that socket: # netstat -untap | grep 12351 {no output} # grep 12351 /proc/net/tcp {no output} # lsof | grep 12351 {no output} # fuser -n tcp 12351 {no output, repeating the python test fails again} # nc localhost 12351 {no output} # nmap localhost 12351 {shows port closed} Other high ports work fine (eg 12352 works) Is there something magic about this port? Is there somewhere else I can look? Where does python find out that socket is in use that netstat doesnt know about? Any other way I can find out what/if that socket is?

    Read the article

< Previous Page | 134 135 136 137 138 139 140 141 142 143 144 145  | Next Page >