Search Results

Search found 21142 results on 846 pages for 'bit manipulation'.

Page 139/846 | < Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >

• Repeated disconnects on WPA PEAP network

  - by exasperated

  My school has a WPA PEAP network with GTC inner authentication. I am able to connect to the network, but once I load a website or two, the network become unresponsive (i.e. in Chromium, it gets stuck at "Sending request"), and I'm eventually disconnected. Any help will be greatly appreciated. Here's some log output. I can provide more if needed: Ubuntu 13.04 3.8.0-32-generic x86_64 lsusb: 03:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24) lsmod: iwldvm                241872  0  mac80211              606457  1 iwldvm iwlwifi               173516  1 iwldvm cfg80211              511019  3 iwlwifi,mac80211,iwldvm dmesg: [    3.501227] iwlwifi 0000:03:00.0: irq 46 for MSI/MSI-X [    3.503541] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 [    3.527153] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled [    3.527162] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS enabled [    3.527170] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled [    3.527178] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [    3.527186] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_P2P disabled [    3.527192] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6235 AGN, REV=0xB0 [    3.527240] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [    3.551049] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [  375.153065] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.159727] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [  375.553201] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [  375.559871] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 1892.110738] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 1892.117357] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5227.235372] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5227.242122] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5817.817954] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 5817.824560] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 5824.571917] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 5824.571929] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 5824.571935] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 6956.290061] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 6956.296671] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 6963.080560] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 6963.080566] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 6963.080570] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 7613.469241] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 7613.475870] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 7620.201265] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 7620.201278] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 7620.201285] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [ 8232.762453] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [ 8232.769065] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [ 8239.581772] iwlwifi 0000:03:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 8239.581784] iwlwifi 0000:03:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP [ 8239.581792] iwlwifi 0000:03:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP [13763.634808] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [13763.641427] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 [16955.598953] iwlwifi 0000:03:00.0: L1 Disabled; Enabling L0S [16955.605574] iwlwifi 0000:03:00.0: Radio type=0x2-0x1-0x0 lshw:    *-network        description: Wireless interface        product: Centrino Advanced-N 6235        vendor: Intel Corporation        physical id: 0        bus info: pci@0000:03:00.0        logical name: wlan0        version: 24        serial: b4:b6:76:a0:4b:3c        width: 64 bits        clock: 33MHz        capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless        configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-32-generic firmware=18.168.6.1 ip=10.250.169.96 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn        resources: irq:46 memory:f7c00000-f7c01fff iwlist scan: Cell 02 - Address: 24:DE:C6:B0:C7:D9                     Channel:36                     Frequency:5.18 GHz (Channel 36)                     Quality=29/70  Signal level=-81 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=0000004ff3fe419b                     Extra: Last beacon: 27820ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030124                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1624001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3424001B000000FF000000000000000000000000000000           Cell 04 - Address: 24:DE:C6:B0:C3:E9                     Channel:149                     Frequency:5.745 GHz                     Quality=28/70  Signal level=-82 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=000000181f60e19c                     Extra: Last beacon: 28680ms ago                     IE: Unknown: 0009436174436861743278                     IE: Unknown: 01088C129824B048606C                     IE: Unknown: 030195                     IE: Unknown: 050400010000                     IE: IEEE 802.11i/WPA2 Version 1                         Group Cipher : CCMP                         Pairwise Ciphers (1) : CCMP                         Authentication Suites (1) : 802.1x                     IE: Unknown: 2D1ACC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: 3D1695001B000000FF000000000000000000000000000000                     IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00                     IE: Unknown: DD1E00904C33CC011BFFFF000000000000000000000000000000000000000000                     IE: Unknown: DD1A00904C3495001B000000FF000000000000000000000000000000                     IE: Unknown: DD07000B8601040817                     IE: Unknown: DD0E000B860103006170313930333032           Cell 09 - Address: 24:DE:C6:B0:C0:29                     Channel:149                     Frequency:5.745 GHz                     Quality=39/70  Signal level=-71 dBm                       Encryption key:on                     ESSID:"CatChat2x"                     Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s                               36 Mb/s; 48 Mb/s; 54 Mb/s                     Mode:Master                     Extra:tsf=00000112fb688ede                     Extra: Last beacon: 27716ms ago ifconfig (while connected): wlan0     Link encap:Ethernet  HWaddr b4:b6:76:a0:4b:3c             inet addr:10.250.16.220  Bcast:10.250.31.255  Mask:255.255.240.0           inet6 addr: fe80::b6b6:76ff:fea0:4b3c/64 Scope:Link           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1           RX packets:230023 errors:0 dropped:0 overruns:0 frame:0           TX packets:130970 errors:0 dropped:0 overruns:0 carrier:0           collisions:0 txqueuelen:1000            RX bytes:255999759 (255.9 MB)  TX bytes:16652605 (16.6 MB) iwconfig (while connected): wlan0     IEEE 802.11abgn  ESSID:"CatChat2x"             Mode:Managed  Frequency:5.745 GHz  Access Point: 24:DE:C6:B0:C0:29              Bit Rate=6 Mb/s   Tx-Power=15 dBm              Retry  long limit:7   RTS thr:off   Fragment thr:off           Power Management:off           Link Quality=36/70  Signal level=-74 dBm             Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0           Tx excessive retries:0  Invalid misc:3   Missed beacon:0

  Read the article

• Recommended installation for Asus EEE 1015PEM Netbook

  - by David B

  Hi, I just got my Asus EEE PC 1015PEM netbook with Windows 7 starter... obviously, I'd like to install Ubuntu (not sure yet if I'd like to dual boot or completely remove win7). Anyway, I never had a netbook before. I know about unity but heard some bad stuff about it, so I wonder if I might be better sticking to the desktop edition. What do you think? any recommendations? Also, should I use the 32 bit or 64 bit version?

  Read the article

• Getting started with ClojureScript and Google Closure

  - by Andrea

  I would like to investigate whether ClojureScript, with the associated Google Closure library is a reasonable tool to build modern, in-browser, Javascript applications. My current Javascript stack consists of jQuery, Backbone and RequireJS with the possible additions of some widgets libraries like jQueryUI or KendoUI. So it will be quite a big leap (I already know how to work in Clojure, although I have little experience). What is a good roadmap to do so? Should I learn the Google Closure library first, or can I grasp it together with ClojureScript? One thing I am concerned about is the overall application structure. Backbone is rather opinionated on how to organize your application. I am not sure whether Google Closure also includes some components to help with the design of the application. And, if this is the case, I do not know how to tell whether this structure will port to ClojureScript or a ClojureScript application will require a different organization anyway, and only use - say - the widgets and DOM manipulation features of Closure.

  Read the article

• Endeca Information Discovery 3-Day Hands-on Training Workshop

  - by Mike.Hallett(at)Oracle-BI&EPM

  For Oracle Partners, on October 3-5, 2012 in Milan, Italy: Register here. Endeca Information Discovery plays a key role with your big data analysis and complements Oracle Business Intelligence Solutions such as OBIEE. This FREE hands-on workshop for Oracle Partners highlights technical know-how of the product and helps understand its value proposition. We will walk you through four key components of the product: Oracle Endeca Server—A highly scalable, search-analytical database that derives the data model based on the data presented to it, thereby reducing data modeling requirements. Studio—A highly interactive, component-based user interface for configuring advanced, yet intuitive, analytical applications. Integration Suite—Provides rapid unification and enrichment of diverse sources of information into a single integrated view. Extensible Value-Added Modules—Add-on modules that provide value quickly through configuration instead of custom coding. Topics covered will include Data Exploration with Endeca Information Discovery, Data Ingest, Project Lifecycle, Building an Endeca Server data model and advanced modeling techniques, and Working with Studio. Lab Outline The labs showcase Oracle Endeca Information Discovery components and functionality by providing expertise on features and know-how of building such applications. The hands-on activities are based on a Quick Start application provided during the class. Audience Oracle Partners, Big Data Analytics Developer and Architects BI and EPM Application Developers and Implementers, Data Warehouse Developers Equipment Requirements This workshop requires attendees to provide their own laptops for this class. Attendee laptops must meet the following minimum hardware/software requirements: Hardware 8GB RAM is highly recommended (Windows 64 bit Machine is required) 40 GB free space (includes staging) USB 2.0 port (at least one available) Software One of the following operating systems: 64-bit Windows host/laptop OS (Windows 7 or Windows Server 2008) 64-bit host/laptop OS with a Windows VM (Server, or Win 7, BIC2g, etc.) Internet Explorer 8.x , Firefox 3.6 or Firefox 6.0 WINRAR or 7ziputility to unzip workshop files: Download-able from http://www.win-rar.com/download.html Download-able from http://www.7zip.com/ Oracle Endeca Information Discovery Workshop Register here: October 3-5, 2012: Cinisello Balsamo, Milan.  We will confirm with you your place within 2 weeks. Questions?  Send email to: [email protected]  :  Oracle Platform Technologies Enablement Services.

  Read the article

• Which Programming Languages Support the Following Features?

  - by donalbain

  My personal programming background is mainly in Java, with a little bit of Ruby, a tiny bit of Scheme, and most recently, due to some iOS development, Objective-C. In my move from Java to Objective-C I've really come to love some features that Objective-C has that Java doesn't. These include support for both static and dynamic typing, functional programming, and closures, which I'm trying to leverage in my code more often. Unfortunately there are trade-offs, including lack of support for generics and (on iOS at least) no garbage collection. These contrasts have lead me to start a search for some of the programming languages that support the following features: Object Oriented Functional Programming Support Closures Generics Support for both Static and Dynamic Typing Module Management to avoid classpath/dll hell Garbage Collection Available Decent IDE Support Admittedly some of these features(IDE support, Module Management) may not be specific to the language itself, but obviously influence the ease of development in the language. Which languages fit these criteria?

  Read the article

• Channel 9 Video:SharePoint and WCF

  - by Sahil Malik

  Ad:: SharePoint 2007 Training in .NET 3.5 technologies (more information). A VERY LONG TIME AGO :), Zhiming from Microsoft and I got together and talked a bit about why WCF is such a big deal in SharePoint. In this video we talk a bit about why SharePoint has been so successful. And why WCF in SharePoint can have a great positive impact on your productivity. A lot of what I say in that video is still applicable to SP2010, but that video was recorded before there was ANY information out in the general world about SP2010. Well, that video is now finally online .. enjoy! :) Comment on the article ....

  Read the article

• A small Class for simplifying the Work with URL Parameters

  An article describing a simple class that makes working with URL parameters a little bit easier.

  Read the article

• Is there a way to play the role of Javascript with any other language like C#?

  - by Gulshan

  Is there a way to play the role of Javascript with any other language like C#? One way came up in my head is, having silverlight installed, using C# instead of Javascript for all the client side scripting (Though C# is not a scripting language). Is it possible? I am not talking about something like GWT(Java) or Script#(C#). Probably the question can be stated as- "With silverlight installed, can I do everything supported by Javascript(like DOM manipulation etc) with C#?" Hope it's clearer.

  Read the article

• Common Javascript mistakes that severely affect performance?

  - by melee

  At a recent UI/UX MeetUp that I attended, I gave some feedback on a website that used Javascript (jQuery) for its interaction and UI - it was fairly simple animations and manipulation, but the performance on a decent computer was horrific. It actually reminded me of a lot of sites/programs that I've seen with the same issue, where certain actions just absolutely destroy performance. It is mostly in (or at least more noticeable in) situations where Javascript is almost serving as a Flash replacement. This is in stark contrast to some of the webapps that I have used that have far more Javascript and functionality but run very smoothly (COGNOS by IBM is one I can think of off the top of my head). I'd love to know some of the common issues that aren't considered when developing JS that will kill the performance of the site.

  Read the article

• What do you use to bundle / encrypt data?

  - by David McGraw

  More and more games are going the data driven route which means that there needs to be a layer of security around easy manipulation. I've seen it where games completely bundle up their assets (audio, art, data) and I'm wondering how they are managing that? Are there applications / libraries that will bundle and assist you with managing the assets within? If not is there any good resources that you would point to for packing / unpacking / encryption? This specific question revolves around C++, but I would be open to hear how this is managed in C#/XNA as well. Just to be clear -- I'm not out to engineer a solution to prevent hacking. At the fundamental level we're all manipulating 0's and 1's. But, we do want to keep the 99% of people that play the game from simply modifying XML files that are used to build the game world. I've seen plenty of games bundle all of their resources together. I'm simply curious about the methods they're using.

  Read the article

• My site is getting popular, bandwidth expensive

  - by ElbertF

  I'm running a (small) image hosting site which has been getting a little bit of traction lately (2,000 to 5,000 visitors a day, spikes up to 10,000). It's hosted on Linode and I've already run out of the bandwidth for this month (300 GB). I've experimented with Amazon S3 but that was costing me $5 a day, Linode currently costs me $30 a month. I get a tiny bit of revenue from ads (Adsense and Black Label Ads) but it's not enough to break even. What should I do? Obviously I'd like to keep running the site but not if it starts costing me a lot of money.

  Read the article

• Get Specific depth values in Kinect (XNA)

  - by N0xus

  I'm currently trying to make a hand / finger tracking with a kinect in XNA. For this, I need to be able to specify the depth range I want my program to render. I've looked about, and I cannot see how this is done. As far as I can tell, kinect's depth values only work with pre-set ranged found in the depthStream. What I would like to do is make it modular so that I can change the depth range my kinect renders. I know this has been down before but I can't find anything online that can show me how to do this. Could someone please help me out? I have made it possible to render the standard depth view with the kinect, and the method that I have made for converting the depth frame is as follows (I've a feeling its something in here I need to set) private byte[] ConvertDepthFrame(short[] depthFrame, DepthImageStream depthStream, int depthFrame32Length) { int tooNearDepth = depthStream.TooNearDepth; int tooFarDepth = depthStream.TooFarDepth; int unknownDepth = depthStream.UnknownDepth; byte[] depthFrame32 = new byte[depthFrame32Length]; for (int i16 = 0, i32 = 0; i16 < depthFrame.Length && i32 < depthFrame32.Length; i16++, i32 += 4) { int player = depthFrame[i16] & DepthImageFrame.PlayerIndexBitmask; int realDepth = depthFrame[i16] >> DepthImageFrame.PlayerIndexBitmaskWidth; // transform 13-bit depth information into an 8-bit intensity appropriate // for display (we disregard information in most significant bit) byte intensity = (byte)(~(realDepth >> 8)); if (player == 0 && realDepth == 00) { // white depthFrame32[i32 + RedIndex] = 255; depthFrame32[i32 + GreenIndex] = 255; depthFrame32[i32 + BlueIndex] = 255; } // omitted other if statements. Simple changed the color of the pixels if they went out of the pre=set depth values else { // tint the intensity by dividing by per-player values depthFrame32[i32 + RedIndex] = (byte)(intensity >> IntensityShiftByPlayerR[player]); depthFrame32[i32 + GreenIndex] = (byte)(intensity >> IntensityShiftByPlayerG[player]); depthFrame32[i32 + BlueIndex] = (byte)(intensity >> IntensityShiftByPlayerB[player]); } } return depthFrame32; } I have a strong hunch it's something I need to change in the int player and int realDepth values, but i can't be sure.

  Read the article

• Do I have to completely reinstall Ubuntu now that it won't boot?

  - by Dave M G

  I just tried installing software called Teamviewer. It said there was some kind of error with unresolved dependancies. Then I realized I was trying to install the 32 bit version, but I needed to install the 64 bit version. So I tried that, and I got an error saying that Ubuntu needed to do a partial upgrade. I thought that was weird, so I just wanted to abandon installing anything and get out of this. I exited all programs and rebooted, and now I can't get back into Ubuntu. After the GRUB screen I get a black screen and no login options. If I boot into recovery, I get the following screen: I booted up a live CD of 12.04 to see if that could help, but it seems the only option is to completely reinstall Ubuntu. Can I repair this in any way, or is my only option to make a fresh install?

  Read the article

• WIn API Basic Paint program

  - by Tom Burman

  Just trying to learn a bit of Win API. Im trying to make a basic drawing app, a bit like MS Paint. For the time being im trying to get one function to work which is, when you left click and drag the mouse around the screen a line is drawn behind the mouse. Heres what i have so far, but for some reason: 1) the line starts drawing straight away rather then waiting for the left click 2) the line isn't solid its very dotty. case WM_MOUSEMOVE: { if(MK_LBUTTON){ hdc = GetDC(hwnd); hPen = CreatePen(PS_SOLID,5,RGB(0, 0, 255)); SelectObject(hdc, hPen); int x = LOWORD(lParam); int y = HIWORD(lParam); MoveToEx(hdc,x,y,NULL); LineTo(hdc, LOWORD(lParam), HIWORD(lParam)); ReleaseDC(hwnd,hdc); } else break; } } Thanks for any help!

  Read the article

• What technologies are used for Game development now days?

  - by Monika Michael

  Whenever I ask a question about game development in an online forum I always get suggestions like learning line drawing algorithms, bit level image manipulation and video decompression etc. However looking at games like God of War 3, I find it hard to believe that these games could be developed using such low level techniques. The sheer awesomeness of such games defy any comprehensible(for me) programming methodology. Besides the gaming hardware is really a monster now days. So it stands to reason that the developers would work at a higher level of abstraction. What is the latest development methodology in the gaming industry? How is it that a team of 30-35 developers (of which most is management and marketing fluff) able to make such mind boggling games?

  Read the article

• Believeland

  - by AllenMWhite

  My daughter sent me this link to an article on ESPN called Believeland , which is a bit of a Tolstoy, but gives you a bit of the feel of what it's like to be from Cleveland. We love our city, even as many of us leave it for greener (and warmer) pastures elsewhere. One of the things I hope you'll find when you come here for SQL Saturday 60 on February 5, is what a great place it is to live here. Our call for speakers is open until Sunday. I hope to see you here. Allen...(read more)

  Read the article

• More Maintenance Plan Weirdness

  - by AjarnMark

  I’m not a big fan of the built-in Maintenance Plan functionality in SQL Server.  I like the interface in SQL 2005 better than 2000 (it looks more like building an SSIS package) but it’s still a bit of a black box.  You don’t really know what commands are being run based on the selections you have made, and you can easily make some unwise choices without realizing it, such as shrinking your database on a regular basis.  I really prefer to know exactly what commands and with which options are being run on my servers. Recently I had another very strange thing happen with a Maintenance Plan, this time in SQL 2005, SP3.  I inherited this server and have done a bit of cleanup on it, but had not yet gotten around to replacing the Maintenance Plans with all my own scripts.  However, one of the maintenance plans which was just responsible for doing LOG backups was running more frequently than that system needed, and I thought I would just tweak the schedule a bit.  So I opened the Maintenance Plan and edited the properties of the Subplan, setting a new schedule, saved it and figured all was good to go.  But the next execution of the Scheduled Job that triggers the Maintenance Plan code failed with an error about the Owner of the job.  Specifically the error was, “Unable to determine if the owner (OldDomain\OldDBAUserID) of job MaintenancePlanName.Subplan has server access (reason: Could not obtain information about Windows NT group/user 'OldDomain\OldDBAUserID’..”  I was really confused because I had previously updated all of the jobs to have current accounts as the owners.  At first I thought it was just a fluke, but it happened on the next scheduled cycle so I investigated further and sure enough, that job had the old DBA’s account listed as the owner.  I fixed it and the job successfully ran to completion. Now, I don’t really like mysteries like that, so I did some more testing and verified that, sure enough, just editing the Subplan schedule and saving the Maintenance Job caused the Scheduled Job to be recreated with the old credentials.  I don’t know where it is getting those credentials, but I can only assume that it is the same as the original creator of the Maintenance Plan, and for some reason it insists on using that ID for the job owner.  I looked through the options in SSMA and could not find anything would let me easily set the value that I wanted it to use.  I suspect that if I did something like executing sp_changeobjectowner against the Maintenance Plan that it would use that new ID instead.  I’m sure that there is good reason that it works this way, but rather than mess around with it much more, I’m just going to spend my time rolling out my replacement scripts instead. Chalk this little hidden oddity up as yet one more reason I’m not a fan of Maintenance Plans.

  Read the article

• E-Business Suite R12 Certified on 2012 Hyper-V Windows Guests

  - by John Abraham

  Oracle E-Business Suite Release 12 (12.1) is now certified on Windows Server 2008 (32-bit) and Windows Server 2008 R2 running as guest operating systems within Window Server 2012 Hyper-V virtual machines. Hyper-V is a built-in feature of Microsoft Windows Server that allows for the creation and management of virtualized computing environments. With this certification, the E-Business Suite is now supported on the above Windows virtualized guest operating systems in a similar way to non-virtualized Windows. References Note 761567.1 - Oracle E-Business Suite Installation and Upgrade Notes Release 12 (12.1.1) for Microsoft Windows Server (32-bit) Note 1188535.1 - Migrating Oracle E-Business Suite R12 to Microsoft Windows Server 2008 R2 Note 1563794.1 - Certified Software on Microsoft Windows Server 2012 Hyper-V Windows Server Hyper-V Overview

  Read the article

• Atheros AR928X wireless connection makes neighbourhood machine drop off line

  - by funicorn

  I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

  Read the article

• What exactly can shaders be used for?

  - by Bane

  I'm not really a 3D person, and I've only used shaders a little in some Three.js examples, and so far I've got an impression that they are only being used for the graphical part of the equation. Although, the (quite cryptic) Wikipedia article and some other sources lead me to believe that they can be used for more than just graphical effects, ie, to program the GPU (Wikipedia). So, the GPU is still a processor, right? With a larger and a different instruction set for easier and faster vector manipulation, but still a processor. Can I use shaders to make regular programs (provided I've got access to the video memory, which is probable)? Edit: regular programs == "Applications", ie create windows/console programs, or at least have some way of drawing things on the screen, maybe even taking user input.

  Read the article

• Some websites are not opening. What should I do? [closed]

  - by Jamal

  Some websites are not opening in my system. I am using Ubuntu 11.04. Earlier, when I was using Ubuntu 10.01, there was no such issue. I have tried Firefox as well as Chromium and I am sure the issue is not with the browser. same websites are opening perfectly with Windows. Google, Twitter and Ubuntu related websites are running perfect. Other websites like www.downrightnow.com, easy-mantra.com are not opening. Installed Wubi on windows7 (32 bit). Ubuntu 12.10 is 64 bit. Processor Intel core 2 Duo. $ cat /etc/resolv.conf <-- Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) -- DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN -- output --> nameserver 127.0.1.1

  Read the article

• Black Screen When Booting From .VDI Image

  - by GTyler

  I have cloned a VirtualBox machine, which runs Ubuntu 11.04 32-bit as Guest OS. I now wish to transfer it to a new host machine running Windows Vista 32-bit. I’ve transferred the .vdi file and adjusted the name and memory. However when I boot it, the options to choose the Linux version came up: Ubuntu, with Linux 2.6.38-10-generic, Linux 2.6.38-10-generic(recovery mode) , Previous Linux versions, Memory test. Once I chose Linux 2.6.38 a black screen just appears with an underscore at the top. What should I do to get it to run? I don’t have my original machine near me now so I can only work with my .vdi image. My VB is version 4.0.10. I have tried cloning this VDI and also assigning a new UUID and making a new guest, but I still got the black screen. Thank you.

  Read the article

• PHP to SharePoint roadmap

  - by Daryl Gubler

  I'm a PHP developer with familiarity with Rails and a focus on MVC development. My company is moving more and more to SharePoint and I feel I need to learn to build application within the SharePoint system. I have some brief introduction to C# but that's about it. I've used some SharePoint Designer and the web interface but not that heavily (most of my "development" so far for SharePoint has been html/css/javascript page manipulation in SPDesigner). What, and in what order should I be learning to eventually develop applications for SharePoint? Also, any good resources for each step?

  Read the article

• Advice: How to overcome the "accent" barrier in cross-geographical teams ?

  - by shan23

  I'm an Indian working in a MNC. As a result, I often have to attend(and contribute) to meetings where I have to listen to people who have a pronounced American accent. Some are still understandable, but a couple of people I have interact with speak such a different form of English, I mostly have to guess at what they are saying. When I ask them to clarify, they often speak the same sentence in the same tenor/speed, so my net gain is zero. My question is, how to politely put it across that due to their accent, I can't understand a thing, and may they please speak slowly and a bit clearly ? Some people might take it a bit personally, since "everyone else" is understanding them perfectly...and I don't want to cause offense at all. Any ideas ?

  Read the article

• What are the basic skills a beginner JavaScript programmer should have?

  - by Sanford

  In NYC, we are working on creating a collaborative community programming environment and trying to segment out software engineers into differing buckets. At present, we are trying to define: Beginners Intermediates Advanced Experts (and/or Masters) Similar to an apprenticeship, you would need to demonstrate specific skills to achieve different levels. Right now, we have identified beginner programming skills as: Object - method, attributes, inheritance Variable - math, string, array, boolean - all are objects Basic arithmetic functions - precedence of functions String manipulation Looping - flow control Conditionals - boolean algebra This is a first attempt, and it is a challenge since we know the natural tension between programming and software engineering. How would you create such a skills-based ranking for JavaScript in this manner? For example, what would be the beginner JavaScript skills that you would need to have to advance to the intermediate training? And so on.

  Read the article

< Previous Page | 135 136 137 138 139 140 141 142 143 144 145 146  | Next Page >