Search Results

Search found 13909 results on 557 pages for 'old man'.

Page 141/557 | < Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• How can I use my cell phone to establish a dial-up networking connection?

  - by gWiz

  I am using Windows 7 and have a BlackBerry with T-Mobile (U.S.). I have paired the phone with my computer over Bluetooth, which automatically creates a serial port for it. I am able to open the port in PuTTY and successfully issue AT commands to the modem, including dialing. However, while using Windows to create and establish a Dial-Up Networking connection, I get an error dialog stating "Error 678. The remote computer did not respond." In my testing, I also tried setting up a connection to dial a number connected to a phone. When attempting to connect over this connection, the phone does ring but the very moment I answer the call, my computer displays the above error dialog. What must be done to successfully establish such a PPP connection? Some special AT initialization string perhaps? To clarify, I'm not referring to the well-described and popular technique known as "tethering," in which the remote host of the data link is the mobile service provider. I am interested specifically in establishing direct data links with remote hosts other than my mobile service provider. Think old-school landline connection to your friend's computer or BBS. Edit 1 As grawity pointed out in comments, the missing piece of the puzzle is the actual modulator that is compatible with v-series protocols, which I expected to be built into the cellphone. So far the best only software alternative I could find is this experimental project. Edit 2 Found this forum discussion today. The participants state that there is no old-school modem in the BlackBerry. Edit 3 When I place a call in PuTTY with ATD, immediately after the call is answered (and the callee is initiating the handshake) the cellphone returns OK. This is not the expected behavior for establishing a data connection. The phone should reciprocate the handshake, and upon success return CONNECT. (Alternatively it should return BUSY or NO CARRIER, but never simply OK.) Windows DUN must be interpreting this as the "Error 678" I was seeing.

  Read the article

• Linux kernel - can't access sda16 & sda17

  - by osgx

  I can't access sda16 sda17 and higher partitions from my linux. This linux is rather debian (very old); kernel 2.6.23. So, I know that so old linux kernel can't access 16 partitions on single sata disk. What version of kernel should I use to be able access sda16, sda17 etc? I want to update only a kernel, not a whole Linux distribution. PS. There is an WindowsNT kernel which can access and format 16, 17 or higher partition, but my intention is to use sda16 and sda17 from linux (I want Linux Kernel). PPS: dmesg: sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 > sd 2:0:0:0: [sda] Attached SCSI disk sd 4:0:0:0: [sdb] xxx 512-byte hardware sectors ... So, there is no mapping of sda16, sda17, ... to sdb. Sdb is the second physical hard drive.

  Read the article

• How to access original files from before a symlink gets updated, which have since been moved to another dir

  - by Luke Cousins

  We have a website and our deployment process goes somewhat like the following (with lots of irrelevant steps excluded) echo "Remove previous, if it exists, we don't need that anymore" rm -rf /home/[XXX]/php_code/previous echo "Create the current dir if it doesn't exist (just in case this is the first deploy to this server)" mkdir -p /home/[XXX]/php_code/current echo "Create the var_www dir if it doesn't exist (just in case this is the first deploy to this server)" mkdir -p /home/[XXX]/var_www echo "Copy current to previous so we can use temporarily" cp -R /home/[XXX]/php_code/current/* /home/[XXX]/php_code/previous/ echo "Atomically swap the symbolic link to use previous instead of current" ln -s /home/[XXX]/php_code/previous /home/[XXX]/var_www/live_tmp && mv -Tf /home/[XXX]/var_www/live_tmp /home/[XXX]/var_www/live # Rsync latest code into the current dir, code not shown here echo "Atomically swap the symbolic link to use current instead of previous" ln -s /home/[XXX]/php_code/current /home/[XXX]/var_www/live_tmp && mv -Tf /home/[XXX]/var_www/live_tmp /home/[XXX]/var_www/live The problem we are having and would like help with is that, the first thing any website page load does is work out the base dir of the application and define it as a constant (we use PHP). If then during that page load a deployment occurs, the system tries to include() a file using the original full path and will get the new version of that file. We need it to get the old one from the old dir which has now moved as in: System starts page load and determines SYSTEM_ROOT_PATH constant to be /home/[XXX]/var_www/live or by using PHP's realpath() it could be /home/[XXX]/php_code/current. Symlink for /home/[XXX]/var_www/live get updated to point to /home/[XXX]/php_code/previous instead of /home/[XXX]/php_code/current where it did originally. System tries to load /home/[XXX]/var_www/live/something.php and gets /home/[XXX]/php_code/current/something.php instead of /home/[XXX]/php_code/previous/something.php I'm sorry if that is not explained very well. I'd really appreciate some ideas on how to get around this problem if someone can. Thank you.

  Read the article

• iTunes copy just metadata (song and album ratings, playlists) from iPod

  - by Jared Updike

  I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

  Read the article

• Grayed-Out Sleep and Hibernate Options on Windows 7 After Updating Graphics Driver

  - by Maxim Zaslavsky

  I have a Gateway M275 Tablet PC, on which I've installed Windows 7 Ultimate. The laptop is quite old, so there aren't any Win7 drivers for it, not to mention any Vista drivers. Win7 has been working for some time, but I noticed that my video output wasn't working. I went into Device Manager and found that I didn't have a driver for my video card: it just recognized it as the standard one. I searched online and found an XP driver for it, released by Gateway. Device Manager accepted this driver and prompted me to reboot. After that, I noticed that my Sleep and Hibernate options in the Shut Down menu have been grayed-out. I looked online and found that many people are attributing this to display drivers, as such an old driver would surely not be compatible with the standby procedures Windows 7 uses. To make it clear: I was able to Sleep and Hibernate before updating the drivers; now, I can't. Running powercfg /a gives me, "An internal system component has disabled this standby state," for each available standby mode. Is there some way that the driver can be modified to support hibernation? The new driver fixed my video output problem, but I guess hibernation is more important for me. If not, what steps should I take to remove the driver and just leave the standard Windows one, which previously supported hibernation and sleep on this computer? Thanks in advance.

  Read the article

• How to verify system using right GPU, after system reset [duplicate]

  - by Antoros

  This question already has an answer here: Is my mobile AMD card being used? 2 answers OS: Windows 8 CPU: Intel® Core™ i7 Processor 3635QM GPU 1 : Intel HD Graphics 4000 GPU 2 : AMD Radeon™ HD 8870M other info: System Spects Problem: im unsure that CCC is using AMD card instead of Intel's, i have encountered several issues since updating to 8.1 and i don't know what to do What happened: Installed 8.1 patch first day After 1 minute of use, BBSOD, windows never loaded again System restore wouldnt recognize 8.0 restore points i did a system reset to windows 8 since the laptop was only 3 weeks old System Broke, it did restore to factory BUT kept the registry almost intact, i had to install almost everything again, since the factory drivers where working with the updated one's registry and several problems CCC Broke too <- What i've already done Installing new drivers on top of old ones didnt work, so i used AMD uninstaller first Uninstalled and Re-installed Intel's HD Graphics Driver Tried to install mobile center, but AMD told me that it wasnt compatible (even if thats the only driver that they provide via their page as seen Here) Tried to use Auto-Detect, couldnt install driver because card was disabled because it didnt have the drivers... (see what they did here?) Had to use a workaround with Samsung Update, the driver didnt appear as download so had to use search and downloaded the driver manually. Now the graphic card appears on device manager and catalyst but as 8800 series (not exact model), and cant check the card with neither dxdiag/GPU-z/HWMonitor when right-clicking on CCC only Intel card appears launching a game and using as "high performance" would speed it up a little but i cant be sure How to verify its working properly? HWMonitor wont show AMD card even when set to high performance Latest GPU-Z wont work because a problem with Intel's, and legacy ones wont either what can I do now? I don't even know if I fixed my problem or not, and i also want to to use Adobe Premier with it, and its locked (the option to run it with the amd card not intels) Edit: now it seems to work, but cant change the setting for adobe Premiere and other programs that i Need to

  Read the article

• SQL Server Subscriber Migration

  - by SuperCoolMoss

  We're currently have one way transaction replication from a SQL Server 2005 OLTP publisher/distrbituor to two subscribers (one SQL 2005 and the other SQL2008 R2). Replication security is via the SQL Agents' domain service account (the same account is used on all boxes). The SQL2008R2 subscriber is used for BI purposes and hosts a database that has a subset of the Production publisher database tables, with different security and indexes. We need to migrate this BI subscriber to a newer box with more performant hardware. The plan is as follows: Stop replicating to the BI box (continue replicating to the other subscriber). Backup all databases on the BI box (including system databases). Restore all databases (including master in single user mode) to the new BI box (this has SQL Server 2008R2 already installed). Take the old BI box off the network and shut it down. Rename and Re-IP the new BI box to be the same as the old box. Switch replication back on. Are there any flaws in this approach?

  Read the article

• What can I do with a home server?

  - by Joel Coehoorn

  I have an old 700 Mhz Pentium III at home running Windows 2000 Server, with a home router set up to pass incoming requests to it and a DynDNS account set up so it's easy to find. Right now I'm using it for a number of things: Shared folders + backup inside the home network Shared Printer inside the home network Domain Controller, just because I feel like it and because it's useful to me as practice to keep those "enterprise" administration skills. Web Server FTP remote access for my files. I abandoned this for security reasons, but it's still worth leaving visible. Remote Desktop in to the home network (thinking about adding VPN service) SVN repository MySQL - Will be moving to SQL Server 2008 Standard soon. After I upgrade my wife's laptop from home to pro later this year it will also become a domain controller It's the only place I still have access to Internet Explorer 6 any more without setting up a new virtual machine, so I use it for testing code with that browser. The question is: What else could I be doing with this machine? Update Additional ideas based on the suggestions: Media Server/DVR Build server PBX SSH Proxy Server Continuous Integration Server Personal OpenID Provider Update2 Just a note that this server was recently upgraded to an Atom330 with 2 GB ram and bigger hard drive. For all that's slow for a "modern" cpu, it should still be much faster than the old Pentium III and the expected power savings should make the upgrade essentially free over the course of the next year or two. Also, it's now running Windows Server 2008.

  Read the article

• How do I activate the F_LINE input in a transplanted HP chassis?

  - by admin

  I have an HP Pavilion Media Center PC chassis, vintage 2003 or so and I replaced the motherboard in it with a newer (vintage 2009) HP motherboard, M2N68-LA (Narra 5). I have scoured the internet trying to find pinouts for the motherboard to no avail. My question concerns the front panel audio, specifically Line In. The old chassis was built for AC97 but the new mobo is build for the newer HD audio standard. I figured out by comparison & experimentally how to connect the Mic & Headphone jacks to the HD audio header of the mobo by adding a manual switch to set the SENSE lines. Now all works fine for Mic & headphone. The old chassis also has a front panel Line In jack that the newer HP chassis does not have. However, the new mobo has a 4 pin white connector labeled F_LINE that I believe is a line input. Under Windows 7 I see the two Line Inputs in the mixer but I can't get one of them to become active. The 4 pin F_LINE connector uses the two middle pins for ground, and presumably the other two for left and right audio inputs. There are no pins for sensing on that connector. Can anyone tell me how to use that F_LINE input for the front panel, or how to activate it?

  Read the article

• Configure New Server for .htaccess

  - by Phil T

  I have a new LAMP CENTOS 5 server I am setting up and trying to copy the configuration from another web server I have. I am stuck with what I think is a mod_rewrite problem. If I go to http://old-server.com/any_page_name.php it correctly routes through some handling code in index.php and shows me a graceful "Page Cannot Be Displayed" message. But if I go to http://new-server.com/any_page_name.php I get an ugly Apache 404 Not Found error message. I looked in both httpd.conf files and they both have only one reference to mod_rewrite. LoadModule rewrite_module modules/mod_rewrite.so So it seems like that should be fine. At the bottom of httpd.conf I have the code: <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/html ServerName new-server.com ErrorLog logs/new-server.com-error_log CustomLog logs/new-server.com-access_log common </VirtualHost> Then in the root of /var/www/html I have the exact same .htaccess file that looks like this: RewriteEngine on Options +FollowSymlinks RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . index.php [L] ErrorDocument 404 /page-unavailable/ <files ~ "\.tpl$"> order deny,allow allow from none deny from all </files> So I don't see why the page load at old-server.com works fine while new-server.com doesn't route through index.php like I want it to do. Thanks.

  Read the article

• My new SSD is causing issues. How can I solve them?

  - by Allan

  Computer specs 1 TB harddisc 120 GB 520intel SSD 8 GB DDR3 RAM Athlon Phenom II x64 955 3. 2ghz DK DFI Lanparty FX7900 M3H3 motherboard ASUS ATI RADEON HD6970 2 GB I have bought a new SSD (Intel 520, 120 GB), and wanted to use this as my system disc. I removed the other harddisc, and installed the SSD with the newest firmware. And then Windows 7 I updated Windows 7 with no problems and then put back my old harddrive. I formatted that old harddrive just to clean up at the same time... So at this stage everything was perfect. My new SSD was set as Master 0 Primary it boots on it and I have 1 TB emptyu harddrive I can use for whatever I want. So far no errors at all Now here is the problem, I installed a few games and everytime I tried to play the computer would say Windows must restart because DCOM server process launcher service terminated, or it says Windows must now restart because the Plug and Play service terminated unexpectedly Most commonly this error is caused by a rootkit virus, well I have tried formatting my entire computer, and running every antivirus I could find, so that shouldn't be it. I've also read somewhere it might happen when there are hardware issues. That on the otherhand would make sense, as I just put in a new SSD. I don't expect you to know this error. I haven't found anyone who knew it yet. maybe you can me guide through what might have gone wrong when I placed in the SSD? What have I checked regarding the SSD? It displays the right name when the computer starts up It has the newest firmware Did a 'sfc /scannow' which told me everything was fine I don't know what to do from here. Everything seems to work great with the drive. when I start playing games my computer crashes.

  Read the article

• Getting a "CPU over temperature error", but temperatures seem to be normal

  - by Luis Parker

  I built a PC with the following parts: CPU: i5-2500 Motherboard: Asus P8H67-M EVO rev 3.0 RAM: G-Skill Ripjaws Series 8GB (2 x 4GB) DDR3 1333 Video: GTX 560-Ti 1GB I used a crappy (but functioning) old case and a 500W Powercooler supply. The rig also includes 3 HDs and a DVD-RW. Whenever I push the system mildly it resets right away (looks more like power off/power on) and gives me a "CPU over temperature error". However, BIOS always reports <65ºC for the CPU at the moment of the reset, same as Core Temp and RealTemp. This is RealTemp's log since launching BF3 until the reset (just over 1 minute, as you can see) Just to be sure I've checked the CPU cooler and re-applied the thermal paste twice, but nothing changed. I'm not overclocking at all. What am I missing here? Could it be that the old power supply is generating this error? Maybe the mobo isn't reporting temperatures correctly? I don't have a clue on how to troubleshoot this, help Thanks in advance!

  Read the article

• Linux iptables / conntrack performance issue

  - by tim

  I have a test-setup in the lab with 4 machines: 2 old P4 machines (t1, t2) 1 Xeon 5420 DP 2.5 GHz 8 GB RAM (t3) Intel e1000 1 Xeon 5420 DP 2.5 GHz 8 GB RAM (t4) Intel e1000 to test linux firewall performance since we got bitten by a number of syn-flood attacks in the last months. All machines run Ubuntu 12.04 64bit. t1, t2, t3 are interconnected through an 1GB/s switch, t4 is connected to t3 via an extra interface. So t3 simulates the firewall, t4 is the target, t1,t2 play the attackers generating a packetstorm thorugh (192.168.4.199 is t4): hping3 -I eth1 --rand-source --syn --flood 192.168.4.199 -p 80 t4 drops all incoming packets to avoid confusion with gateways, performance issues of t4 etc. I watch the packet stats in iptraf. I have configured the firewall (t3) as follows: stock 3.2.0-31-generic #50-Ubuntu SMP kernel rhash_entries=33554432 as kernel parameter sysctl as follows: net.ipv4.ip_forward = 1 net.ipv4.route.gc_elasticity = 2 net.ipv4.route.gc_timeout = 1 net.ipv4.route.gc_interval = 5 net.ipv4.route.gc_min_interval_ms = 500 net.ipv4.route.gc_thresh = 2000000 net.ipv4.route.max_size = 20000000 (I have tweaked a lot to keep t3 running when t1+t2 are sending as many packets as possible). The result of this efforts are somewhat odd: t1+t2 manage to send each about 200k packets/s. t4 in the best case sees aroung 200k in total so half of the packets are lost. t3 is nearly unusable on console though packets are flowing through it (high numbers of soft-irqs) the route cache garbage collector is no way near to being predictable and in the default setting overwhelmed by very few packets/s (<50k packets/s) activating stateful iptables rules makes the packet rate arriving on t4 drop to around 100k packets/s, efectively losing more than 75% of the packets And this - here is my main concern - with two old P4 machines sending as many packets as they can - which means nearly everyone on the net should be capable of this. So here goes my question: Did I overlook some importand point in the config or in my test setup? Are there any alternatives for building firewall system especially on smp systems?

  Read the article

• iTunes copy just metadata (song and album ratings, playlists) from iPod

  - by Jared Updike

  I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

  Read the article

• File sharing problem on Windows Server 2003 x64

  - by O. Askari

  Hi, We have a customer that hosts our .NET application server on Windows Server 2003 x64. The problem is, its file sharing gets totally disabled after about 10-30 minutes. The only way to re-enable it is to restart the server but the same thing happens again after each restart. This server contains SQL Server 2005 Enterprise, .NET Framework 3.5 and our .NET based application server. We haven't had such a problem with any other customer before so we asked them to prepare another server to deploy our application on it. We installed our application server on the new machine and let SQL Server remain on the old one. Unfortunately the same problem happened to the new machine too. Now the old machine works only as database server and the new one works as application server but both of them have the same file sharing problem. File sharing on both machines doesn't get disabled on the same time but it eventually happens to both of them. I wonder why is this happening and how to find the reason to this problem. Any suggestion or solution is much appreciated.

  Read the article

• my cpu won't start. all fan were spinning for a second then nothing happen

  - by Tommy

  I need help about this.. I'm from Malaysia.. Back then my cpu is all okay..and it's 4 year old.. I think this question is answered before but i'm still don't understand.. when i plugged my cpu..turn it on and all of the fan (graphic card, mobo fan and PSU fan) were spinning just for a second than nothing happen.. I don't know if it is because of the PSU or my mobo.. I sent my cpu to the shop and they said it must be the mobo.. They tell me to change my mobo and PSU also..and it cost over 100 buck (rm300 in Malaysia). and i'm real 'dry' right now. My whole data is inside the HDD. School projects, photos, games, and many..I really-really need my cpu back alive.. My mobo is MSI MS-7529 with dual core chips. My PSU is ATX-480W. the PC store guy said i need to change to new ASUS mobo if I want. I dont know what type it is but Then he tell me to change my PSU also because he don't think my old PSU (ATX-480W) ain't compatible to the new mobo.. I was very need a help from you techie guys.. sorry for my terrible English..

  Read the article

• Trying to retrieve data with a thermaltake blacX enclosure: Windows 7 believes the drive to be "uninitialized"

  - by Peeter Joot

  I have a laptop that won't boot. It appears to be a power problem ... laptop auto-turns-off within about 10 seconds of pressing the power button (with power buttons lighted temporarily and no display with or without external monitor). I've followed the dell troubleshooting guide which suggested reseating the memory modules and the hard drives, but that didn't help. Before trying to have the laptop serviced, I wanted to get some data off off the hard drive. I bought a thermaltake blacX enclosure, intending to use this to both use to retrieve the drive data with, and then later use as external storage. Following the instructions (insert cables, insert drive power on) goes fine, and Windows 7 on another laptop installs the device driver software. However, no drive letter shows up in 'Computer'. Under Computer-manage-storage I see the drive is there, and there's an option to "initialize" the drive. The Windows "initialize" dialog gives me the option to pick between "MBR" and "GPT" partitioning, which sounds like a good way to destroy the data on the drive. I'm thinking that I've purchased the wrong device for the job (or that my old drive is damaged). The old drive to recover info from is a Western Digital 500G/7200rpm SATA drive if that is relavent. Both the original laptop and the one I'm using for recovery are running Windows 7. Does anybody have experience with using a blacX enclosure to recover data off an already formatted drive?

  Read the article

• Some doubts about the use of usermod and groupmod command

  - by AndreaNobili

  I am not yet a true "Linux guy" and I have the following doubts about how exactly do the following shell procedure (a list of commands steps) founded in a tutorial that I am following (I want deeply understand what I am doing before do it): sudo passwd root then login again as root usermod -l miner pi usermod -m -d /home/miner miner groupmod -n miner pi exit So at the beginning it enable the root account and I have to login again in the system as root...this is perfectly clear for me. And now I have the followings doubts: 1) The usermod command: usermod -l miner pi usermod -m -d /home/miner miner Reading the official documentation of the usermod command I understand that this command modify the informations related to an existing account Reading the documentation it seems to me that the -l parmether modify the name of the user pi in miner and then the -m -d paramether move the contents of the old home directory to the new one (named miner) and use this new directory as home directory My doubt is: what exactly do the executions of these operation? I think that: Rename the existing pi user in miner Then move the content of the old home directory (the pi home directory? or what?) into a new directory (/home/miner) that now is the home directory for the miner user. Is it right? The the second doubt is related to this command groupmod -n miner pi It seems to me that change the group name from pi in miner But what exactly is a group in Linux and why is it used? Tnx

  Read the article

• Grayed-Out Sleep and Hibernate Options on Windows 7 After Updating Graphics Driver

  - by Maxim Z.

  I have a Gateway M275 Tablet PC, on which I've installed Windows 7 Ultimate. The laptop is quite old, so there aren't any Win7 drivers for it, not to mention any Vista drivers. Win7 has been working for some time, but I noticed that my video output wasn't working. I went into Device Manager and found that I didn't have a driver for my video card: it just recognized it as the standard one. I searched online and found an XP driver for it, released by Gateway. Device Manager accepted this driver and prompted me to reboot. After that, I noticed that my Sleep and Hibernate options in the Shut Down menu have been grayed-out. I looked online and found that many people are attributing this to display drivers, as such an old driver would surely not be compatible with the standby procedures Windows 7 uses. To make it clear: I was able to Sleep and Hibernate before updating the drivers; now, I can't. Running powercfg /a gives me, "An internal system component has disabled this standby state," for each available standby mode. Is there some way that the driver can be modified to support hibernation? The new driver fixed my video output problem, but I guess hibernation is more important for me. If not, what steps should I take to remove the driver and just leave the standard Windows one, which previously supported hibernation and sleep on this computer? Thanks in advance.

  Read the article

• When to raise domain functional level?

  - by Joel Coel

  We very recently completed a project to retire two old domain controllers running Server 2003 R2. They are now replaced with shiny new 2008 R2 boxes. However, the functional level of the domain has not yet been updated for the 2008 R2 servers, just in the long-shot case of the need for a rollback to the old controllers. I expect to have the all clear to update the domain by next weekend. I also want to note that our desktop clients are still 95% Windows XP. However, we're about to start a project to update our 200 or so clients to Windows 7 before the end of the calendar year. Is there any advantage to holding the domain at the 2003 functional level while we are still supporting more Windows XP than Windows 7, especially given that some of the management stations are still XP? Update: I forgot to mention earlier that we still have a pair of windows 2000 servers (not domain controllers) that support some legacy software. I'm working to replace those, but in the meantime I need to be sure that Windows 2000 can still participate in a 2008 R2 domain.

  Read the article

• Rescue system running TFS that BSODs, into vmware esxi

  - by 3molo

  Hi, After moving to new facilities, one of our old Dell servers running Windows Server 2003 R2 on PowerEdge 2650 HW BSODs with 0x8e. The server runs Team Foundation Server, so we have a few guys dependent on it. No one here knows TFS, so we have no idea how difficult it would be to setup from scratch. We have the MSSQL database(s) backed up, recent and fresh copy. Tried removing/refitting memory modules, but with no success. The system boots into safe mode but hangs occasionally. I booted a linux livecd and did a dd of both c: and d:, so I have all the data in compressed images on a vmware machine. For the guest, I created a 38G (actually it became 40GB) partition to act as C:, and booted a live cd. I then uncompressed the compressed disk image of c: and dd'd it to the new c: using 'gunzip -dc c.img.gz | dd of=/dev/sda1 bs=1M'. The operation ran for about 1000 seconds, and completed successfully. I assumed it would at least try to boot windows (but most likely BSOD due to not having correct drivers), but the Vmware ESXi guest does not seem to recognize it as a bootable disk. We don't have the vmware enterprise license, so the vmware converter cold cloning is not an option. Did I do something wrong in my dd's etc with the ISOs, or why would it not (try to) boot? Am I wasting my time? What other approach is there? Will continue to try to remove services and drivers to make the physical machine at least work reasonably well in safe mode. What do you suggest? 1. Continue to get the dd'd images to the virtual disk and get it to boot. 2. Install a new windows server, get team foundation server and restore from backup. 3. Focus on the old problematic hardware Any help appreciated

  Read the article

• Windows 7 automatically logs out when logging in

  - by Luke

  A Windows 7 HP x64 computer is set to automatically log in (no password), but once it starts logging in, it starts to load the desktop after the welcome screen, but before icons or background images are loaded, it goes to the Welcome screen saying 'Logging Off'. I can log in with Safe Mode, and I ran a couple different virus scans, with no detections. I also tried checking the userinit.exe file in System32 (as suggested by MANY users for Windows XP), but it's the same version as a working system. I also checked the registry under HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon for the SHELL and UserInit values, but they look normal. I tried to disable all startup items (through MSCONFIG) to select Diagnostic boot, but then I get a blue screen about the video driver not loading. Any other ideas? EDIT I created a new user, and it could log in no problems. I am thinking it's the NTUSER.DAT file. I just renamed it to NTUSER.DAT.old, then tried logging in as the problem user. I could log in, but as a TEMP profile. His profile folder is now C:\Users\TEMP, and his old folder is still accessible but in the wrong location. EDIT 2 I can't seem to turn off the TEMP profile, so I'm open to other suggestions. Copying the folders (i.e. Documents, Music, etc) does not work, as it creates an additional TEMP.000 then TEMP.001 folder each time the user logs in.

  Read the article

• HD working with IDE USB adapter but not recognised by bios

  - by Rajeeva

  I have a Windows XP Pentium III desktop with two hard drives. The first one has the OS and is luckily working. The second drive on the secondary master IDE channel few days back was unable to read some files and since then for some time it was failing and reviving intermittently and now it is always showing as failed on the IDE channel When the HD was intermittenly failing, I was able to copy some data from it to the other drive - also during that time if the system was running and the hard disk failed at that time, the system froze and then i had to reboot. then I got a new 80 gb hdd similar (same make - seagate barracuda) to the earlier failing one, a new data cable for the drive and an IDE to USB adapter. the new hard drive i installed in the previous drive's place (secondary master), formatted it and it worked for 1 day and then it also failed - simultaneously i connected the old hd to the IDE/USB adapter and i could view all the data - some of that data i was able to back up from the old hd to the new hd before the new hd failed the new hd i have tried connecting on the primary channel as the slave disk but when i do that then the bios does not detect either the OS drive or the new drive and the system does not boot surprisingly, the older (previously failed) hd and the new hd are both working fine on the usb channel with the IDE/USB adapter. i have ruled out any problem with the secondary channel since the dvd rom i was earlier using as primary slave have now connected to secondary master and it works fine. i am really confused by this behavior on my system. please can anybody try to solve this for me. thanks.

  Read the article

< Previous Page | 137 138 139 140 141 142 143 144 145 146 147 148  | Next Page >