Search Results

Search found 5318 results on 213 pages for 'managed c'.

Page 142/213 | < Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >

• NTFS partition size not recognized after disaster recovery clone

  - by djechelon

  I'm in the middle of a disaster recovery of a 250GB hard disk that was "clicking". Obviously I didn't have a backup copy. I managed to salvage all the files thanks to GParted Live that was able to read the disk without a single "click" sound. So I cloned the partition to a new drive sized 500GB. Unfortunately, GParted process went to some kind of infinite loop, disks stopped I/O and after a couple of hours I interrupted the clone process I started. Now the problem is: when cloning the partition I also chose to expand 250GB to the whole 500GB of the target disk. Windows sees the partition sized 500GB in computer management, but Windows Explorer only sees 250. chkdsk e: /f says the filesystem is OK. How can I repair the file system and let Windows see the full 500GB of the new partition? An alternate idea is to deep-copy the files from the backup disk to a newly formatted disk. This should definitely fix. Any other ideas?

  Read the article

• How could Load average numbers from 'htop' exceed 100% CPU utlization?

  - by Joe Huang

  I use 'htop' to monitor my web server. It's recently quite loaded and the Load average is showing something like this: Load average: 3.10 2.56 1.63 I searched the web about these numbers and I found an article about it: http://blog.scoutapp.com/articles/2009/07/31/understanding-load-averages In the article, it says if I have 2 CPUs, 2.0 means 100% CPU utilization. And my VPS has two CPUs, so what does 3.1 mean? How could it exceed 100% CPU utilization? And from these numbers, does it mean I should be wary about the loading now? But the performance seems totally fine, and this is a managed VPS, the hosting company has not notified me any warning about it. During day time, Load average always show these high numbers... here is another snapshot while writing. Load average: 3.03 2.77 1.97 Load average: 0.41 1.29 1.60 <---- 5 more minutes later So I am wondering how much room left for this site to grow in current configurations? What kind of proactive actions I should take in advance? I don't want to wait until the server bursts. Thanks.

  Read the article

• How to detect/list rogue computers connected to a WIFI network without access to the Wifi Router interface?

  - by JJarava

  This is what I believe to be an interesting challenge :) A relative (that leaves a bit too far to go there in person) is complaining that their WIFI/Internet network performance has gone down abysmally lately. She'd like to know if some of the neighbors are using her wifi network to access the internet but she's not too technically savvy. I know that the best way to prevent issues would be to change the Router password, but it's a bit of a PITA having to re-configure all wifi devices... and if the uninvited guest broke the password once, they can do it again... Her wifi router/internet connection is provided by the telco, and remotely managed so she can log-on to their telco account's page and remotely change the router's Wifi password, but doesn't have access to the router status page/config/etc unless she opts out of the telco's remote support and mainteinance service... So, how could she check if there are guests in the wifi with this restrictions and in the most "point and click way"? In this case I'd probably use nmap to look for other devices in the network, but I'm not sure if that's the easiest way to do it. I'm not a wifi expert, so I don't know if there are any wifi-scanning utils that can tell us who's talking to the router... Lastly, she's a Windows user as I guess that'll influence the choice of tools available Any suggestions more than welcome Regards!

  Read the article

• Netbook thinks it is a desktop

  - by Narcolapser

  Question: Are, and if so what, there packages for download that I can get netbook to understand it is not a desktop and that it is a netbook. Info: I'm running an Acer Aspire One with ubuntu desktop 9.10. I tried Ubuntu Netbook Remix first but it has graphics issues with the aspire one. So I changed to Ubuntu Desktop. It was the only distro (after debian, centOS, Fedora, and Knoppix all failed me) that I managed to get working. The only thing is that it is having issues doing things that a netbook/laptop should be doing. most notably is that it will run it's battery dead if I close the screen and throw it into my back pack. It seems to just stay fully on and runs it's self to death. also it will lock up some times if I close the screen and come back to it 10 or 20 minutes later. It also won't retain volume settings when I reboot, as well as screen brightness. and just a couple of other things that I can't quite put my finger on, but just seem amiss. like I said, Essentially my netbook thinks it is a desktop, how can I fix this? ~N

  Read the article

• filesystem compatible with freenas and windows

  - by Daniel

  Hi all, I'm planning on using FreeNAS (was considering openfiler but freenas seems simpler) for my home NAS box running off ESXI. I have managed to get local sata drives to mount in ESXI (http://serverfault.com/questions/216902/esxi-add-datastore-without-partitioning). I've had one of the drives fail on my before and I was able to retrieve most of the data off it using windows tools (I'm not much of a linux guy I know enough to be dangerous!). If I go the freenas route in the event that something goes bad what would be the best file system to use so that I could pop the drive out of the freenas box (vm) and put it in another pc running windows so I could try and run various recovery tools to get the data back. All in all its not a major problem if I lose the data just would be a bit annoying, so I'm not looking for suggestions around backing up etc. I was considering using NTFS that the drives are already formatted as but it appears that while freenas does support NTFS that its a bit buggy and not 100% reliable, anyone know if this is still true? Read that on a forum somewhere.

  Read the article

• Dynamic subdomain routing

  - by Nader

  Hi everyone, I asked this question over at stackoverflow, but got very few views: http://stackoverflow.com/questions/2284917/route-web-requests-to-different-servers-based-on-subdomain Perhaps it's more applicable to this crowd. Here it is again for convenience: I have a platform where a user can create a new website using a subdomain. There will be thousands of these, eg abc.mydomain.com, def.mydomain.com . Hopefully if we are successful hundreds of thousands. I need to be able to route these domains to a different IPs to point at a particular app server. I have this mapping in a database right now. What are the best practices and recommended technologies here? I see a couple options: Have DNS setup with a wildcard CNAME entry so that all requests go to a single IP where perhaps two machines using heartbeat (for failover) know how to look up the IP in the database and then do an http redirect to the appropriate app server. This seems clunky and slow to me. Run my own DNS server that can be programatically managed such that when a new site is created a DNS entry is added. We also move sites around to different app servers, so I would need to be able to update DNS entries in close to real time. Thoughts anyone? Thanks. Update2: I've setup external wildcard DNS pointing at an HAProxy web server whose job it is to route requests to backend servers. The mapping is stored in our internal PowerDNS server. Question now is how to get the HAProxy server (or another) to use the value of the internal DNS and not some config file or access list? – Update: Based on some suggestions below, it seems like reverse-proxy server(s) is the way to go. As I'll be rebalancing the domain-server mapping, these need to work instantly and the TTL on a DNS solution could be a problem. Any recommendations on software to use considering this domain-IP data is stored in a DB, and I'll need this to be performant?

  Read the article

• Need for explanation: NetBIOS over TCP/IP on VMware network adapter disturbs access to network share

  - by gyrolf

  (Moved here from StackOverflow) Some time ago nearly all workstations in our team (Windows XP SP2) exhibited intermittend but frequent delays when accessing shares on the network. Typically the first access to a share which hadn't been accessed for some time resulted in a nearly frozen workstation for up to 30 seconds. Then everything started working fine again. Using TCPView from Sysinternals I saw that during this delays there was a connection to the netbios-ssn port on the file server which was in state SYN_SENT. First try: Disable NetBIOS over TCP/IP for the intranet network adapter. Problem solved, but I didn't like to manipulate our centrally managed network configuration for the intranet. Second try: Disable NetBIOS over TCP/IP only for the VMWare network adapter (VMNet1 used for host only communications). Problem solved again! My questions: Why does NetBIOS over TCP/IP on one network adapter disturb NetBIOS over TCP/IP on another network adapter? Is this problem specific to VMWare network adapters? Has anybody else seen this phenomen? Additional information: VMWare Workstation version 6.0.3 At the time I started seriously analysing the problem it was no more possible to find out what had been changed to our systems at the time the problems started.

  Read the article

• No internet access when using static IP

  - by Endy Tjahjono

  I have just upgraded to Windows 8.1, and after the upgrade process is finished, I can't connect to internet. I tried running the "Troubleshoot problems": It concluded that DHCP needs to be activated: I let it activate DHCP, and I got internet connection back. The problem is I want to set this PC to a certain IP address (the IP address that it has been using all this time). I am also using Hyper-V, which I suspect has something to do with this problem. After I regained internet connection, I tried running one of my Hyper-V VM. From inside the VM I can connect to internet. That VM has static IP address. I also noticed that in "Control Panel\Network and Internet\Network Connections", I usually have a network connection called vEthernet (Realtek PCIe GBE Family Controller Virtual Switch). I didn't find it there after upgrade. How do I set my PC to a static IP while retaining internet access in Windows 8.1? EDIT I have managed to recreate vEthernet (Realtek PCIe GBE Family Controller Virtual Switch) by unchecking Allow management operating system to share this network adapter in Hyper-V's Virtual Switch Manager and then checking it again. But when I changed the adapter to use static IP, it still can't connect to internet. Result of Get-NetAdapter -Name * | fl (with MAC address removed): Name : vEthernet (Realtek PCIe GBE Family Controller Virtual Switch) InterfaceDescription : Hyper-V Virtual Ethernet Adapter #2 InterfaceIndex : 5 MacAddress : 55-55-55-55-55-55 MediaType : 802.3 PhysicalMediaType : Unspecified InterfaceOperationalStatus : Up AdminStatus : Up LinkSpeed(Mbps) : 100 MediaConnectionState : Connected ConnectorPresent : False DriverInformation : Driver Date 2006-06-21 Version 6.3.9600.16384 NDIS 6.40 Name : Ethernet 3 InterfaceDescription : Hyper-V Virtual Ethernet Adapter #3 InterfaceIndex : 6 MacAddress : 55-55-55-55-55-56 MediaType : 802.3 PhysicalMediaType : Unspecified InterfaceOperationalStatus : Up AdminStatus : Up LinkSpeed(Gbps) : 10 MediaConnectionState : Connected ConnectorPresent : False DriverInformation : Driver Date 2006-06-21 Version 6.3.9600.16384 NDIS 6.40 Name : Ethernet InterfaceDescription : Realtek PCIe GBE Family Controller InterfaceIndex : 2 MacAddress : 55-55-55-55-55-57 MediaType : 802.3 PhysicalMediaType : 802.3 InterfaceOperationalStatus : Up AdminStatus : Up LinkSpeed(Mbps) : 100 MediaConnectionState : Connected ConnectorPresent : True DriverInformation : Driver Date 2013-05-10 Version 8.1.510.2013 NDIS 6.30

  Read the article

• Shared files folder in Amazon Elastic Beanstalk environment

  - by por

  I'm working on a Drupal application, which is planned to be hosted in Amazon Elastic Beanstalk environment. Basically, Elastic Beanstalk enables the application to scale automatically by starting additional web server instances based on predefined rules. The shared database is running on an Amazon RDS instance, which all instances can access properly. The problem is the shared files folder (sites/default/files). We're using git as SCM, and with it we're able to deploy new versions by executing $ git aws.push. In the background Elastic Beanstalk automatically deletes ($ rm -rf) the current codebase from all servers running in the environment, and deploys the new version. The plan was to use S3 (s3fs) for shared files in the staging environment, and NFS in the production environment. We've managed to set up the environment to the extent where the shared files folder is mounted after a reboot properly. But... The Problem is that, in this setup, the deployment of new versions on running instances fail because $ rm -rf can't remove the mounted directory, and as result, the entire environment goes down and we need restart the environment, which isn't really an elegant solution. Question #1 is that what would be the proper way to manage shared files in this kind of deployment? Are you running such an environment? How did you solve the problem? By looking at Elastic Beanstalk Hostmanager code (Ruby) there seems be a way to hook our functionality (unmount if mounted in pre-deploy and mount in post-deploy) into Hostmanager (/opt/hostmanager/srv/lib/elasticbeanstalk/hostmanager/applications/phpapplication.rb) but the scripts defined in the file (i.e. /tmp/php_post_deploy_app.sh) don't seem to be working. That might be because our Ruby skills are non-existent. Question #2 is that did you manage to hook your functionality in Hostmanager in a portable way (i.e. by not changing the core Hostmanager files)?

  Read the article

• PostgreSQL user authentication against PAM

  - by elmuerte

  I am trying to set up authentication via PAM for PostgreSQL 9.3. I already managed to get this working on an Ubuntu 12.04 server, but I am unable to get this working on a Centos-6 install. The relevant pg_hba.conf line: host all all 0.0.0.0/0 pam pamservice=postgresql93 The pam.d/postgressql93 is the default config shipped with the official postgresql 9.3 package: #%PAM-1.0 auth include password-auth account include password-auth When a user tries to authenticate the following is reported in secure log: hostname unix_chkpwd[31807]: check pass; user unknown hostname unix_chkpwd[31808]: check pass; user unknown hostname unix_chkpwd[31808]: password check failed for user (myuser) hostname postgres 10.1.0.1(61459) authentication: pam_unix(postgresql93:auth): authentication failure; logname= uid=26 euid=26 tty= ruser= rhost= user=myuser The relevant content of password-auth config is: auth required pam_env.so auth sufficient pam_unix.so nullok try_first_pass auth requisite pam_succeed_if.so uid >= 500 quiet auth required pam_deny.so account required pam_unix.so account sufficient pam_localuser.so account sufficient pam_succeed_if.so uid < 500 quiet account required pam_permit.so The problem is with the pam_unix.so. It is unable to validate the password, and unable to retrieve the user info (when I remove the auth entry of pam_unix.so). The Centos-6 install is only 5 days old, so it does not have a lot of baggage. The unix_chkpwd is suid and has execute rights for everybody, so it should be able to check the shadow file (which has no privileges at all?).

  Read the article

• Performance experiences for running Windows 7 on a Thin-Client?

  - by Peter Bernier

  Has anyone else tried installing Windows 7 on thin-client hardware? I'd be very interested to hear about other people's experiences and what sort of hardware tweaks they had to do to get it to work. (Yes, I realize this is completely unsupported.. half the fun of playing with machines and beta/RC versions is trying out unsupported scenarios. :) ) I managed to get Windows 7 installed on a modified Wyse 9450 Thin-Client and while the performance isn't great, it is usable, particularly as an RDP workstation. Before installing 7, I added another 256Mb of ram (512 total), a 60G laptop hard-drive and a PCI videocard to the 9450 (this was in order to increase the supported screen resolution). I basically did this in order to see whether or not it was possible to get 7 installed on such minimal hardware, and see what the performance would be. For a 550Mhz processor, I was reasonably impressed. I've been using the machine for RDP for the last couple of days and it actually seems slightly snappier than the default Windows XP embedded install (although this is more likely the result of the extra hardware). I'll be running some more tests later on as I'm curious to see particularl whether the streaming video performance will improve. I'd love to hear about anyone's experiences getting 7 to work on extremely low-powered hardware. Particularly any sort of tweaks that you've discovered in order to increase performance..

  Read the article

• Blue screen error code 1000008e

  - by Kas

  I'm getting blue screens, mostly when trying to boot a program that required a lot of memory (games, photo editing software.) So far I've only managed to catch one set of error codes: BCCode: 1000008e BCP1: C0000005 BCP2: ADA393BA BCP3: E9BCEBC4 BCP4: 00000000 OS Version: 6_0_6002 Service Pack: 2_0 Product: 768_1 It's on a Sony VAIO Laptop VGN FW-41E, Vista OS service pack 2. Besides these codes it lists two 'temporary' files that were related with this crash: ...AppData\Local\Temp\WER-134925-0.sysdata.xml ...AppData\Local\Temp\WERDA66.tmp.version.txt When I googled these files some site said it was linked to a worm called 'yodo', but virus scans don't return any results (hitman pro, malware bytes, avast antivirus all turn up empty). Upon further searching about this yodo worm, I came across security stronghold where someone posted they had acquired this worm when downloading access and excel templates. Now, I actually did download templates for the same programs, they might have been the same, they may be related or I might be grasping at straws here. I have not noticed any issues other in performance as of late, just BSOD's when I start software that requires some memory, but I never had issues with these exact same programs before. Help and/or hints are required on how to actually figure out what's the root of this BSOD issue and how can I fix it. Do you reckon it's actually a virus? What program should be able to remove YODO worm stuff?

  Read the article

• Remote management interface for managing ip6tables (or an alternative firewall)

  - by Matthew Iselin

  I'm working with IPv6 and have run into an issue configuring ip6tables on our main router in order to control what can come into the network. A default DROP rule in the FORWARD section has worked well (obviously leaving ESTABLISHED,RELATED as ACCEPT) to keep internal clients' open ports from being accessed. However, running an ip6tables command for every little change is unwieldy. Whilst we are able to continue creating rules manually, I'm wondering if there's some sort of management interface we could use to create the rules quickly and easily. We're looking to be able to save time working on our firewall as well as providing a simple method for modifying rules for those who will eventually replace us. I know webmin (heavily locked down on our network, naturally) has support for modifying iptables rules, but seemingly no support for ip6tables. Something similar would be fantastic. Alternatively, suggestions for a firewall solution apart from iptables/ip6tables which can be managed remotely wouldn't be out of order. A web interface for management is certainly preferable, even if it is just a wrapper with shiny buttons over the raw config files.

  Read the article

• Is there a Windows 7 compatible IPSec VPN client that allows protocol and port specific rules?

  - by Sani Huttunen

  As the title says, I need to find a IPSec VPN client for Windows 7. On XP and Vista we've used SafeNet SoftRemote in which you can set up rules for specific protocols and ports. But SoftRemote isn't compatible with Windows 7. 172.xxx.xxx.1 TCP 1433 172.xxx.xxx.2 TCP 1433 172.xxx.xxx.10 ALL ... Since the VPN gateway is configured this way the client must mirror these settings. I've tried TheGreenBow, NCP Secure Entry, Cisco VPN Client and Shrew Soft VPN but none of these allows you to configure by protocol and port. Does anyone have any other suggestions? EDIT: Forgot to mention that agressive mode is also a requirement. --UPDATE-- I've got some news... I've managed to get SoftRemote to work on Windows 7 x64 through Windows XP Mode. After scouring all corners of the Internet for idéas I had enough information to construct a working solution. This solution will probably benefit other clients as well! You'll find a post here with detailed instructions of how I went about.

  Read the article

• Why am I unable to reach local network computers, but able to browse the web?

  - by Igor Zinov'yev

  I have a weird problem. Today after turning my Ubuntu 9.10 PC on I can't connect to my local network, but I can use the Internet. We have a single Windows 2003 server machine that acts as a local main DNS server, DHCP server and a domain controller. Although it seems to give me the local IP address, I can not ping it, as well as any other machine on the net. I have tried all of the below and it didn't help: Rebooting; Reconnecting to the network; Forcing the dhclient to renew the IP address; Deleting and creating new connection profiles; Plugging my machine into another network outlet; Maybe it has something to do with routing, because I have tampered with routing tables the day before, but the tables seem ok to me: $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 vboxnet0 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 Our LAN uses a D-Link DI-604 router, and it looks to me as if I am connected to the network outside the router. I can not even access its administration page. Please at least suggest what I can do to solve this. P.S. What seems strangest to me is that I can access the PC in question from outside the network by opening a port on the router. I have managed to ssh to it from outside, but I still can't ping nothing on the inside. P.P.S Today I tried reinstalling network-manager with --purge option, but it did no good. After that I created a new DCHP reservation for my PC in order to change my local IP, but that didn't change anything either. My PC is able to get a DHCP offer, but then it's unable to connect to any local computers. I am desperate.

  Read the article

• Software to automate website screenshot capture

  - by Leniel Macaferi

  Do you know any software that can automate the process of getting screenshots of every page of a website? It would act like a spider/crawler/robot. You name it... For example: I developed a website and now I'd like to get a screenshot of every page of the site. I of course could do it manually (a lot of work). For each module of the site (Student, Payment, etc) I have different pages (Create, Edit, Details, Delete, etc) forms. The thing I'm looking for is a software that can visit every link of the site and then capture the screen - a software that can automate the whole process. It would also be good if the software allowed the user to pass a list of URLs to capture screenshots allowing even more fine grained configuration. EDIT: I tried Selenium mentioned by Aaron in his answer but I managed to find an app that does exactly what I needed. It's called Paparazzi!. I wrote a blog post to showcase my attempt at Selenium and the findings regarding Paparazzi!'s batch capture functionality: Software to automate website screenshot capture

  Read the article

• Getting Apache to serve same directory with different authentication over SSL?

  - by Lasse V. Karlsen

  I have set up VisualSVN server, a Subversion server that internally uses Apache, to serve my subversion repositories. I've managed to integrate WebSVN into it as well, and just now was able to get it to serve my repositories through WebSVN without having to authenticate, ie. no username or password prompt comes up. This is good. However, with this set up there is apparently no way for me to authenticate to WebSVN at all, which means all my private repositories are now invisible as far as WebSVN goes. I noticed there is a "Listen 81" directive in the .conf file, since I'm running the server on port 81 instead of 80, so I was wondering if I could set up a https:// connection to a different port, that did require authentication? The reason I need access to my private repositories is that I have linked my bug tracking system to the subversion repositories, so if I click a link in the bug tracking system, it will take me to diffs for the relevant files in WebSVN, and some products are in private repositories. Here's my Location section for WebSVN: <Location /websvn/> Options FollowSymLinks SVNListParentPath on SVNParentPath "C:/Repositories/" SVNPathAuthz on AuthName "Subversion Repository" AuthType Basic AuthBasicProvider file AuthUserFile "C:/Repositories/htpasswd" AuthzSVNAccessFile "C:/Repositories/authz" Satisfy Any Require valid-user </Location> Is there any way I can set up a separate section for a different port, say 8100, that does not have the Satisfy Any directive there, which is what enable anonymous access. Note that a different sub-directory on the server is acceptable as well, so /websvn_secure/, if I can make a location section for that and effectively serve the same content only without the Satisfy Any directive, that'd be good too.

  Read the article

• Do you known a reputable backup software that can capture ONLY file system structure + attributes, WITHOUT file content

  - by bogdan

  Is there, on Windows, a reputable backup software out there capable of capturing ONLY a file system's directory and file structure, along with each item's attributes, WITHOUT capturing the actual file content (all files should be zero-length in the backup). I thoroughly searched the web for a solution and wasn't able to find one. Scenario when this would be very useful: I have a large drive with a huge amount of files. If the drive dies, I don't care so much about the content in these files (I can always download this content again from the Internet at any time) but I do care HUGELY about the names of the files that were on it, possibly also about their MD5 hashes and other classic file attributes (especially created-date / modified-date). The functionality I need is present to an extent in "media"/file cataloging software (i.e. whereisit) and, to a lesser extent, in a Total Commander set of extensions (DiskDir, DiskDirExtended). The huge drawback with cataloging software is that it's not designed to store previous versions of each item (AFAIK) and, most importantly, it has very weak content backup capabilities. I managed to think of a hack but I hope there's some backup software out there that already has this capability and I just failed to find it, thus this question. The hack: RoboCopy could be used with /CREATE (CREATE directory tree and zero-length files only) or /COPY (what to COPY for files) without the D=Data flag, to clone a directory structure into one where all files are zero-length but have the desired attributes. Then I would backup the cloned directory structure with a reputable backup software. I would really love to avoid a hack like this one, if possible. Thanks, Bogdan

  Read the article

• Centos 5.xx Nagios sSMTP mail cannot be sent from nagios server, but works great from console

  - by adam

  I spent last 3 hours of reasearch on how to get nagios to work with email notifications, i need to send emails form work where the only accesible smtp server is the company's one. i managed to get it done from the console using: mail [email protected] working perfectly for the purpouse i set up ssmtp.conf so as: [email protected] mailhub=smtp.company.com:587 [email protected] AuthPass=mypassword FromLineOverride=YES useSTARTTLS=YES rewriteDomain=company.pl hostname=nagios UseTLS=YES i also edited the file /etc/ssmtp/revaliases so as: root:[email protected]:smtp.company.com:587 nagios:[email protected]:smtp.company.com:587 nagiosadmin:[email protected]:smtp.company.com:587 i also edited the file permisions for /etc/ssmtp/* so as: -rwxrwxrwx 1 root nagios 371 lis 22 15:27 /etc/ssmtp/revaliases -rwxrwxrwx 1 root nagios 1569 lis 22 17:36 /etc/ssmtp/ssmtp.conf and i assigned to proper groups i belive: cat /etc/group |grep nagios mail:x:12:mail,postfix,nagios mailnull:x:47:nagios nagios:x:2106:nagios nagcmd:x:2107:nagios when i send mail manualy, i recieve it on my priv box, but when i send mail from nagios the mail log says: Nov 22 17:47:03 certa-vm2 sSMTP[9099]: MAIL FROM:<[email protected]> Nov 22 17:47:03 certa-vm2 sSMTP[9099]: 550 You are not allowed to send mail from this address it says [email protected] and im not allowed to send mails claiming to be [email protected], its suppoused to be [email protected], what am i doing wrong? i ran out of tricks... kind regards Adam xxxx

  Read the article

• How to use WPA2 client mode in the Linux-based Cisco WAP4410N access point

  - by joechip

  I have a Cisco WAP4410N access point that I want to use as a client to connect to a WPA2 wireless network (for WLAN service monitoring purposes). Supposedly this access point supports a "Wireless Client/Repeater" mode that allows to do this. The Repeater function is optional (I have that box unchecked so that nobody can connect to this access point wirelessly). I have verified through SSH that the access point gets configured as a client and not as a Master. But it never associates to the SSID I ask it to. This is what iwconfig shows: ath04 IEEE 802.11ng ESSID:"myownssid" Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:14 dBm Sensitivity=1/3 Retry:off RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/94 Signal level=161/162 Noise level=161/161 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Although I've never done this from the command line, I suppose I could use wpa_supplicant or wpa_client to associate it, but I don't know how to do that without editing configuration files and the filesystem is readonly. Besides, I would have to run those commands manually after every reboot. I'd like to know how to do this the Cisco way, if possible. If not, any trick to make this work would be useful. Edit: This is with the latest firmware, 2.0.4.2. And I found that not all of the filesystem is readonly, since /var and /tmp are mounted with type ramfs.

  Read the article

• Apache 2.2 + mod_fcgid + PHP 5.4: (104) Connection reset by peer

  - by Michele Piccirillo

  On a Debian 6 VPS, I'm running PHP 5.4 via mod_fcgid on a couple of different virtual hosts, managed by Virtualmin GPL. At random, I get 500 Internal Server Errors; restarting Apache brings everything back to normality. Examining the logs, I find messages of this kind: [Thu Oct 04 15:39:35 2012] [warn] [client 173.252.100.117] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Thu Oct 04 15:39:35 2012] [error] [client 173.252.100.117] Premature end of script headers: index.php Any ideas about what is happening? UPDATE: I found a similar question and the author reported to have solved the problem disabling APC. I tried following the advice, but I'm still getting the same errors. VirtualHost configuration SuexecUserGroup "#1000" "#1000" ServerName example.com DocumentRoot /home/example/public_html ScriptAlias /cgi-bin/ /home/example/cgi-bin/ DirectoryIndex index.html index.htm index.php index.php4 index.php5 <Directory /home/example/public_html> Options -Indexes +IncludesNOEXEC +FollowSymLinks +ExecCGI allow from all AllowOverride All AddHandler fcgid-script .php AddHandler fcgid-script .php5 FCGIWrapper /home/example/fcgi-bin/php5.fcgi .php FCGIWrapper /home/example/fcgi-bin/php5.fcgi .php5 </Directory> <Directory /home/example/cgi-bin> allow from all </Directory> RemoveHandler .php RemoveHandler .php5 IPCCommTimeout 61 FcgidMaxRequestLen 1073741824 php5.fcgi #!/bin/bash PHPRC=$PWD/../etc/php5 export PHPRC umask 022 export PHP_FCGI_CHILDREN PHP_FCGI_MAX_REQUESTS=99999 export PHP_FCGI_MAX_REQUESTS SCRIPT_FILENAME=$PATH_TRANSLATED export SCRIPT_FILENAME exec /usr/bin/php5-cgi Package versions webmin-virtual-server/virtualmin-universal 3.94.gpl-2 apache2/squeeze 2.2.16-6+squeeze8 libapache2-mod-fcgid/squeeze 1:2.3.6-1+squeeze1 php5 5.4.7-1~dotdeb.0 php5-apc 5.4.7-1~dotdeb.0

  Read the article

• Destroyed user account on OS X with dscl; how to restore? [migrated]

  - by Sam Ritchie

  I was trying to create a new user on my OS X Lion machine, and somehow managed to destroy my own user's account. Here are the steps I took; hopefully someone here can recognize what I did, and maybe identify some way around this. First, I ran these commands: sudo dscl localhost -create /Local/Default/Users/elasticsearch sudo dscl localhost -create /Local/Default/Users/elasticsearch /bin/bash # mistake! sudo dscl localhost -create /Local/Default/Users/elasticsearch UserShell /bin/bash sudo dscl localhost -create /Local/Default/Users/elasticsearch RealName "Elastic Search" sudo dscl localhost -create /Local/Default/Users/elasticsearch UniqueID 503 # MY uniqueID sudo dscl localhost -create /Local/Default/Users/elasticsearch PrimaryGroupID 1000 sudo dscl localhost -create /Local/Default/Users/elasticsearch NFSHomeDirectory /Local/Users/elasticsearch The big mistake I made here was using "503", which was my user's UniqueID. Immediately my shell username changed to "elasticsearch". I fiddled around, tried to change the current user with sudo su -u sritchie, but this didn't work. On restart, only the "Elastic Search" user was available. I logged into the Lion Recovery partition and reset the root password. After logging in as root and checking on the terminal, I made the remarkable discovery that my home folder was totally empty. I deleted the elasticsearch user, but it made no difference. I don't see anything in Deleted Users either. The odd thing is that when I log in now as myself (sritchie) I can see desktop icons with previews. I can even open a few text files from the Downloads folder if I use the dock alias to Downloads. Could this data be hiding somewhere? Any help would be REALLY appreciated! Thanks, Sam

  Read the article

• How can I debug solutions in Visual Studio 2010 from a network share?

  - by alastairs

  I've recently got a new Mac laptop and am running VS2010 in a Parallels virtual machine. It's mostly working out well for me, but I'm having some problems with debugging specific project types, related to the fact that the projects are being accessed via a network share. Test projects don't run because the test runner can't load the tests' DLL. Web projects fail to run in the Visual Studio mini web server, throwing the following exception: 'An error occurred loading a configuration file: Failed to start monitoring changes to path\to\web.config'. I've spent the evening trawling the web with little luck on this. After reading these two posts, I tried out the usual CasPol changes, but then found this post from one of the early VS2010 betas indicating that CasPol is no longer needed/supported in .NET 4.0 and VS2010. The network share is accessible via both a mapped drive and the UNC path. The virtual machine runs its applications under the administrator account, which appears to have all the necessary permissions on the network share to create, read, write and delete files and folders. I say "appears to have" as I can't view the Security Properties of the appropriate folder via Explorer: the Security tab just isn't present. Has anyone managed to successfully load and debug web and test projects from a network share in VS2010?

  Read the article

• Trouble with HP printer

  - by reyjavikvi

  I have a HP Photosmart C3180 (it's a printer/scanner). For some reason, it recently stopped working. The power light is blinking (I think all the other lights are one, but don't remember, I'm not there right now), and the only way to turn it off is to unplug it. It won't print anything, and when you put a page in the tray it sucks it in without printing anything on it and stops when the paper is on its way out (Again, I don't remember how we managed to get it out, sorry). This printer is hooked up to a computer running XP, but it doesn't work either when printing from the network. Weirdly, the scanner works fine. Do you have any ideas on what could be the problem? Could it be a driver problem? By the way, sorry if the question lacks a bit of detail. I don't know much about printers, and I don't have it here so I can't remember exactly all the details. If needed I can update the question tonight or tomorrow.

  Read the article

• .ashx cannot find type error on IIS7 , no problems on webdev server

  - by Aivan Monceller

  I am trying to make AspNetComet.zip work on IIS7 (a simple comet chat implementation) Here is a portion of my web.config. <system.web> <httpHandlers> <add verb="POST" path="DefaultChannel.ashx" type="Server.Channels.DefaultChannelHandler, Server"/> </httpHandlers> </system.web> <system.webServer> <handlers> <add name="DefaultChannelHandler" verb="POST" path="DefaultChannel.ashx" type="Server.Channels.DefaultChannelHandler, Server"/> </handlers> </system.webServer> When I publish the website on my localhost IIS7 I receive an error: POST http://localhost/DefaultChannel.ashx 500 Internal Server Error Could not load type 'Server.Channels.DefaultChannelHandler The target framework of this project is .Net 2.0 I tried the Classic and Integrated Mode application pool for .Net 2.0 with no luck. I also tried converting the project to 4.0 and tried the Classic and Integrated Mode application pool for .Net 4.0 with no luck. I also tried adding the managed handler through IIS Manager's Handler Mappings. If you have time please download the source (184kb) to reproduce the problem on your own machine. The zip contains a VS2010 solution (.Net 2.0). You could also try to convert this to .Net 4.0 I am using Windows 7 anyway if that matters. If you need more details, please drop your comments below. This is working fine by the way on my webdev server.

  Read the article

< Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >