Search Results

Search found 171078 results on 6844 pages for 'not recognized'.

Page 142/6844 | < Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >

• Website does not resolve in browser but traceroute is successful

  - by Colum

  I am trying to figure out an issue. My internet is working fine, but this one website is not resolving. It works via a proxy, traceroute works: 1 192.168.1.1 (192.168.1.1) 4.205 ms 0.568 ms 0.510 ms 2 * * * 3 67.59.255.13 (67.59.255.13) 10.583 ms 7.949 ms 7.557 ms 4 67.59.255.61 (67.59.255.61) 10.256 ms 9.576 ms 13.083 ms 5 64.15.8.126 (64.15.8.126) 9.943 ms 11.929 ms 11.452 ms 6 64.15.0.217 (64.15.0.217) 14.655 ms 14.092 ms 13.771 ms 7 64.15.0.118 (64.15.0.118) 33.201 ms 34.875 ms 36.544 ms 8 xe-6-0-3.ar1.ord1.us.nlayer.net (69.31.111.169) 34.027 ms 34.957 ms 34.231 ms 9 ae1-30g.cr1.ord1.us.nlayer.net (69.31.111.133) 82.683 ms 35.138 ms 37.592 ms 10 xe-3-0-0.cr2.iad1.us.nlayer.net (69.22.142.26) 41.657 ms 34.063 ms 34.519 ms 11 ae2-30g.ar2.iad1.us.nlayer.net (69.31.31.186) 35.780 ms 36.361 ms 33.968 ms 12 as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 35.086 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.234) 38.031 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 36.833 ms 13 cr1.iad2.inforelay.net (66.231.176.246) 32.595 ms cr2.iad1.inforelay.net (66.231.176.10) 31.771 ms cr1.iad2.inforelay.net (66.231.176.246) 32.622 ms 14 cr1.iad2.inforelay.net (66.231.176.246) 32.956 ms 33.625 ms !X 41.058 ms 15 * cr1.iad2.inforelay.net (66.231.176.246) 35.312 ms !X * 16 * cr1.iad2.inforelay.net (66.231.176.246) 32.814 ms !X * 17 cr1.iad2.inforelay.net (66.231.176.246) 35.459 ms !X * 53.137 ms !X Ping returns this: Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 Request timeout for icmp_seq 4 Request timeout for icmp_seq 5 Request timeout for icmp_seq 6 But what I can not figure out is why my browsers (Firefox, Safari, Opera) can not resolve the domain. I am on a Wifi connection. What could be the problem? BTW I am on a Mac (10.6.5)

  Read the article

• Trying to delete directory with "rm -rf", but get message that it's not empty

  - by Ben Hocking

  I've tried deleting a directory using "rm -rf" and I'm getting the message "Directory not empty": Bens-MacBook-Pro:please benjaminhocking$ ls -lart empty_directory/ total 16 drwxr-xr-x 5 benjaminhocking staff 170 Aug 27 14:46 . drwxr-xr-x 3 benjaminhocking staff 102 Aug 27 15:28 .. Bens-MacBook-Pro:please benjaminhocking$ rm -rf empty_directory/ rm: empty_directory/: Directory not empty Bens-MacBook-Pro:please benjaminhocking$ rmdir empty_directory/ rmdir: empty_directory/: Directory not empty If I try the same thing using Finder (dragging the folder to the Trash), I get the message The operation can’t be completed because the item “empty_directory” is in use. I've tried doing xattr -d com.apple.quarantine, purely out of superstition, but it did no good. A probably important piece of context is that this directory was initially in a directory that should've been deleted by a "make clean" command I issued prior to Terminal locking up on me, after which a little over half of the other programs I had running also locked up, including Skype, and eventually the OS itself. I ended up having to reboot the computer by pressing and holding the power key. Edit to add: Another important piece of information I left off was that this was happening in an encrypted folder à la encfs. I was able to track down the corresponding folder in the encrypted side of things and delete it there. I still don't know why I couldn't do it from the decrypted side of things like I normally do. I'll leave this unanswered for now in case anyone has a good answer for that.

  Read the article

• Is Unix not a PC Operating System?

  - by Corelgott

  I am doing my Bachelor at a university. In a written assignment the professor posted the task: "Name 3 PC-Operating Systems". Well, I went on an included a variety of OS (Linux, Windows, OSx) including Unix & Solaris. Today I recieved a mail from my prof saying: Unix is not a PC-Operating System. Many Unix-variants are not PC-hardware compatible (like AIX & HP-UX. About Solaris: there was one PC-compatible version...) I am kind of suprised: Even if may Unix-variants are Power-PC and different bit-order – Those don't stop being PCs now, right? The question was given in a written assigment! It was not a question that came up during lecture! Due to the original task being in German, I'll include it just to make sure nobody suspects an error in the translation. Frage: Nennen Sie 3 PC-Betriebssysteme. Antwort: Unix ist kein PC-Betriebssystem, viele Unix-Varianten sind nicht auf PC-Hardware lauffähig (AIX, HP-UX). Von Solaris gab es mal eine PC-Variante.

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Any ideas? Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp2 KB896256 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• ssh without password does not work for some users

  - by joshxdr

  I have a new RHEL4 Linux box that I am using to copy data to old Solaris 2.6 and RHEL3 Linux boxes with scp. I have found that with the same setup, it works for some users but not for others. For user jane, this works fine: jane@host1$ ssh -v remhost debug1: Next authentication method: publickey debug1: Trying private key: /mnt/home/osborjo/.ssh/identity debug1: Offering public key: /mnt/home/osborjo/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 277 debug1: read PEM private key done: type RSA debug1: Authentication succeeded (publickey). for user jack it does not: jack@host1 ssh -v remhost debug1: Next authentication method: publickey debug1: Trying private key: /mnt/home/oper1/.ssh/identity debug1: Offering public key: /mnt/home/oper1/.ssh/id_rsa debug1: Authentications that can continue: publickey,password,keyboard-interactive I have looked at the permissions for all the keys and files, they look the same. Since I am using home directories mounted by NFS, the keys for both the remote host and the local host are in the same directory. This is how things look for jane: jane@host1$ ls -l $HOME/.ssh -rw-rw-r-- 1 jane operator 394 Jan 27 16:28 authorized_keys -rw------- 1 jane operator 1675 Jan 27 16:27 id_rsa -rw-r--r-- 1 jane operator 394 Jan 27 16:27 id_rsa.pub -rw-rw-r-- 1 jane operator 1205 Jan 27 16:46 known_hosts For user jack: jack@host1$ ls -l $HOME/.ssh -rw-rw-r-- 1 jack engineer 394 Jan 27 16:28 authorized_keys -rw------- 1 jack engineer 1675 Jan 27 16:27 id_rsa -rw-r--r-- 1 jack engineer 394 Jan 27 16:27 id_rsa.pub -rw-rw-r-- 1 jack engineer 1205 Jan 27 16:46 known_hosts As a last ditch effort, I copied the authorized_keys, id_rsa, and id_rsa.pub from jill to jack, and changed the username in authorized_keys and id_rsa.pub with vi. It still did not work. It seems there is something different between the two users but I cannot figure out what it is.

  Read the article

• svn post-commit not performing

  - by davin

  ive been sitting on this for about 7 hours, and ive aged close to 7 years... ahhh, server admin does that to me. i have svn wired through apache2 with webdav in the usual manner (basically like http://www.howtoforge.com/setting-up-subversion-with-webdav-post-commit-hook-and-multiple-sites-on-jaunty-jackalope-ubuntu-9.04). ive had endless problems with this (i didnt on my previous ubuntu server install, although this is ubuntu 10.10): this happened, and was fixed like in the post: http://stackoverflow.com/questions/2547400/how-do-you-fix-an-svn-409-conflict-error this looks like my issue, although its not my solution: http://serverfault.com/questions/135494/apache-svn-on-ubuntu-post-commit-hook-fails-silently-pre-commit-hook-permis my commit to svn works (finally). although the post-commit hook which is supposed to svn update the working copy of the repo on the server, doesn't work. the post-commit hook itself executes, and has sudo permissions (as in the setup url above. testing with whoami somelogfile.log or sudo whoami somelogfile.log shows www-data and root, respectively), although it wont perform the svn update (sudo svn update /var/www/gameServer /var/svn/gameServer.log). similar to the serverfault url above, when i perform the exact command it does update the working copy to the latest revision, just not through the post-commit hook. an age old question that is 90% of the time a permissions issue. but in pure frustration i chmod 777 lots of stuff not to mention the fact that www-data is in /etc/sudoer so it shouldnt even need that. im collapsing in front of the screen partly out of frustration and partly out of sleepiness. any direction would be appreciated.

  Read the article

• Shell not finding binary when attempting to execute it (it's _definitely_ there)

  - by eegg

  I have a specific set of binaries installed at: ~/.GutenMark/binary/<binaries...> These were previously working correctly, but for seemingly no reason when I attempt to execute them the shell claims not to find them: james@anubis:~/.GutenMark/binary$ ls -al ... -rwxr-xr-x 1 james james 2979036 2009-05-10 13:34 GUItenMark ... -rwxrwxrwx 1 james james 76952 2009-05-10 13:34 GutenMark ... -rwxr-xr-x 1 james james 10156 2009-05-10 13:34 GutenSplit ... james@anubis:~/.GutenMark/binary$ ./GutenMark bash: ./GutenMark: No such file or directory james@anubis:~/.GutenMark/binary$ I've tried to isolate the cause of this, with no success. The same happens with zsh, bash, and sh (all giving their appropriate "file not found" error -- this is definitely not a strange output from the binary itself). The same happens either as user james or as root. Nor is it directory specific; if I move the whole directory installation, or just a single binary, to anywhere else, the same happens when attempting to execute it. The same even happens when I put the directory in $PATH and just execute "GutenMark". It also happens when I execute it from a script (I've tried Python's commands module -- though this appears to just call sh). The problem appears to be specific to the binaries themselves, yet they appear to never actually get executed. Any ideas?

  Read the article

• Firefox not using Kerberos despite being configured to

  - by Nicolas Raoul

  I am deploying Linux/Firefox on a corporate Kerberos network. I followed this Kerberos-on-Firefox procedure but still Firefox does not connect via the company's Kerberos. I am using Firefox 3.0.18 on RedHat EL Server 5.5 Here is what I did: Run kinit on the command line to create a Kerberos ticket Check with klist: the ticket is valid until tomorrow, service principal is krbtgt/[email protected]. In Firefox, set network.negotiate-auth.trusted-uris and network.negotiate-auth.delegation-uris to .dc.thecompany.com. Load the company's portal page via its full hostname: http://server37.thecompany.com/alfresco. (note: server37 is actually the machine I am running Firefox on, but that should not be a problem I guess) PROBLEM: the company's intranet portal still serves me the login/password page. The same portal correctly uses Kerberos on Internet Explorer/Windows 7 machines, same settings, and shows the user's personal page. The server does not see any Kerberos request coming. Did I do something wrong? I enabled NSPR_LOG_MODULES=negotiateauth:5 as explained here, but the log file stays empty.

  Read the article

• Excel 2007 - "The macro may not be available in this workbook" Error

  - by Psycho Bob

  We use an Excel sheet that has been protected to prevent modification of it from end users. All in all they are only able to edit certain tabs to add information that will then be used to generate information on other tabs using equations and such. On the tab with the equations, a button is present called "Prep for Internal Hard Copy Print." This button runs a macro that selects the information on the tab, unprotects it, then sends a print job to the user's default printer that contains the unprotected content. Normally this works like a champ. This time around, however, the macro is throwing the following error: Cannot run the macro "FILENAME.xlsx'!MacroName'. The macro may not be available in this workbook or all macros may be disabled. As far as I can tell, the macros are still present within the workbook. This sheet is normally a .xlsm though the user saved it with a different filename as a .xlsx. Also, the macros appear only as MacroName in the .xlsm file and not "FILENAME.xlsx'!MacroName' as it does in the .xlsx. Finally, when I open the .xlsm it asks if I want to enable the macro content while the .xlsx does not prompt for this. Can anyone tell me what's going on with this sheet or know of a way that I can get the macros working in the .xlsx without having to start over with a different sheet?

  Read the article

• Wireless card on HP laptop not working

  - by D. Strout

  I just bought an HP Envy m6-1125dx online from Best Buy. When I got it home and started it up, the wireless card did not work well - at all. I could connect, but any real usage would cause the connection to start dropping every 30 seconds or so, and it would be really slow. Taking another look at the reviews on the Best Buy site, it seems only a few others had this problem, so I took it to my local Best Buy and exchanged it for another unit. Got it home again and the card had the same issues. Which leads to my dilemma. First: does this model have several different cards that it could come with? Mine is a Ralink RT5390R (on both units I received). If it does, then I can keep exchanging until I get a unit with a different card. I wouldn't ask this, except it seems weird that only a few people mentioned this issue, so I thought that might be one possibility. I looked in to replacing the card with a different one myself, but it seems that HP blocks certain wireless cards. However, some people reported success in replacing the card, and this site said it was only an issue on "older HP computer[s]". Can anyone confirm this? Finally, if that fails/will not work, does anyone know what I can get through Best Buy? I am concerned that they will not put any different card than the Ralink, and after two of those, I don't want that. Can I ask Best Buy support to use a different card? Can they even get another card from HP? I guess the base question is: should I attempt to replace the card myself (two days via Amazon to get a new card), should I try to get the laptop repaired through Best Buy (two - four weeks), should I go for a different model laptop from Best Buy, or should I try a different unit of the same model (three's the charm?).

  Read the article

• Vista - Profile not Loaded Correctly (Cannot Access Registry)

  - by Geoff

  Every so often, I log on and get the Following Message: User profile was not loaded correctly. You have been logged on with a temporary profile. Changes you make to this profile will be lost when you log off. Please see the event log for details or contact your administrator This almost always happens when somebody else has been on the computer for a while, and then I log on. This never used to happen, but now it happens pretty often. My profile is not permanently corrupted, all I have to do is restart my computer, but this annoys me, and I would like to fix it. I was curios about the reason of this cause, so I looked into the Event Log, and found the root of the problem was the ntuser.dat file in the profile that I was logging on to was locked at logon time. This resulted in the current users registry not being loaded, resulting in failure to load the profile. What could be locking this file? is there any way to get a process list without logging on so that I can identify which process has the file locked? Any other suggestions. Hopefully I can find a solution.

  Read the article

• Why cache static files with Varnish, why not pass

  - by Saif Bechan

  I have a system runnning nginx / php-fpm / varnish / wordpress and amazon s3. Now I have looked at a lot of configuration files while setting up the system, and in all of them I found something like this: /* If the request is for pictures, javascript, css, etc */ if (req.url ~ "\.(jpg|jpeg|png|gif|css|js)$") { /* Remove the cookie and make the request static */ unset req.http.cookie; return (lookup); } I do not understand why this is done. Most of the examples also run NginX as a webserver. Now the question is, why would you use the varnish cache to cache these static files. It makes much more sense to me to only cache the dynamic files so that php-fpm / mysql don't get hit that much. Am I correct or am I missing something here? UPDATE I want to add some info to the question based on the answer given. If you have a dynamic website, where the content actually changes a lot, chaching does not make sense. But if you use WordPress for a static website for example, this can be cached for long periods of time. That said, more important to me is static conent. I have found a link with some test and benchmarks on different cache apps and webserver apps. http://nbonvin.wordpress.com/2011/03/14/apache-vs-nginx-vs-varnish-vs-gwan/ NginX is actually faster in getting your static content, so it makes more sense to just let it pass. NginX works great with static files. -- Apart from that, most of the time static content is not even in the webserver itself. Most of the time this content is stores on a CDN somewhere, maybe AWS S3, something like that. I think the varnish cache is the last place where you want to have you static content stored.

  Read the article

• Anti Virus Service does not run - Windows XP SP3 32bit Home

  - by Stefan Fassel

  I have a somewhat strange problem here. I am trying to run Anti Virus Software on my Windows XP Home 32bit System. After a serious crash I had to fall back to an outdated copy of my initial installation and had Windows install 5 years of updates. So far so good. After Intalling a new Anti Virus Software (Bitdefender 2012) everything seemed to be fine, initial scanning went fine and configuration was working. But after restarting the System the Virus Scanner was unable to start up again. Even the Configuration console of the AV Software did not start. I tried scanning the System for malware, but nothing was found. Then I tried a different AV Software (MS Security Essentials), but in the end it did fail to start too. I have tried to start the Service manually, but I seem to be missing the privilege to do so. I am logged in as a Non-"Administrator" User with Admin privileges (Not much choices there on a XP Home System). I cannot switch to Administrator account outside the protected mode. When running Windows in protected mode I am unable to start the AV Software because it does not run in protected mode. I am a bit at loss now...

  Read the article

• Running a service with a user from a different domain not working

  - by EWood

  I've been stuck on this for a while, not sure what permission I'm missing. I've got domain A and domain B, A trusts B, but B does not trust A. I'm trying to run a service in domain A with a user account from domain B and I keep getting Access is Denied. I'm using the FQDN after the username and the password is correct. The user account from domain B is a local administrator on the domain A server, the user account has the logon locally, and as a service permissions. Must. Get. This. Working. Update: I found something interesting in the logs I must have missed. This ought to get me pointed in the right direction. Event ID: 40961 - LsaSrv : The Security System could not establish a secured connection with the server ldap/{server fqdn/fqdn@fqdn} No authentication protocol was available. I've found a few fixes for 40961 but nothing has worked so far. I've verified reverse lookup zones. nslookup resolves the correct dc properly. still workin' at it. Upadte: In response to Evan; I ran " runas /env /user:ftp_user@fqdn "notepad" " then entered the users password and notepad came up. It seems to work successfully. This issue is now resolved. The problem is visible in the screenshot. Windows tries to use the UPN for the user account if you dig your user out of AD with the Browse button. This fails every time even with the right user and password. Simply using the SAM format (Domain\User) works. So simple, yet so annoying. Can't believe I missed this. Thanks to everyone who helped.

  Read the article

• Online computer not responding to pings

  - by mastercork889

  I was doing a bit of scanning on my network lately, knew all the hostnames to each computer connected. But whilst pinging one of them ping returned Request timed out.. This is strange as I know the computer is online and that the computer responds correctly to pinging on a different (enterprise) network. Is there something on the computer, my network, or my computer that is bugging with this? - That's just a sub-question, I don't expect this to be the main answer. The real question: Why does this happen? Why does pinging the IP4 address not work? EDIT : Pinging the Hostname used to default to the IP4 address, but now it defaults to the IP6 address. Why does this happen? But now that it pings using IP6, how come it all of a sudden works? > ping -6 THE_COMPUTER Pinging THE_COMPUTER [lengthy IP6 address] with 32 bytes of data: Reply from [lengthy IP6 address]: time=1ms Reply from [lengthy IP6 address]: time=1ms Reply from [lengthy IP6 address]: time=1ms Reply from [lengthy IP6 address]: time=1ms Ping stats: Sent = 4, Recieved = 4, Lost = 0 (0% loss) But when this is done using IP4 it doesn't work. So there are now two questions: How come IP6 works and not IP4? Why does IP4 not work?

  Read the article

• Require and Includes not Functioning Nginx Fpm/FastCGI

  - by Vince Kronlein

  I've split up my FPM pools so that php will run under each individual user and set the routing correctly in my vhost.conf files to pass the proper port number. But I must have something incorrect in my environment because on this new domain I set up, require, require_once, include, include_once do not function, or rather, they may not be getting passed up to the interpreter to be rendered as php. Since I already have a Wordpress install on this server that runs perfectly, I'm pretty sure the error is in my server block for nginx. server { server_name www.domain.com; rewrite ^(.*) http://domain.com$1 permanent; } server { listen 80; server_name domain.com; client_max_body_size 500M; index index.php index.html index.htm; root /home/username/public_html; location / { try_files $uri $uri/ index.php; } location ~ \.php$ { if (!-e $request_filename) { rewrite ^(.*)$ /index.php?name=$1 break; } fastcgi_pass 127.0.0.1:9002; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } location ~ /\.ht { deny all; } } The problem I'm finding I think is that there are dynamic calls to the doc root index file, while all calls to anything within a sub-folder should be routed as normal ie: NOT passed to index.php. I can't seem to find the right mix here. It should run like so: domain.com/cindy (file doesn't exist) --> index.php?name=$1 domain.com/admin/anyfile.php (files DO exist) --> admin/anyfile.php?$args

  Read the article

• tab complete not working for vim in particular directory - ubuntu 12.04

  - by user1160958

  I am working on a ruby on rails app. All of the sudden the command line tab complete stopped working for vim, only for files though, and only for the vim command (i.e. works for other commands, ls, rm etc.) After further investigation - this only occurs in a specific directory, the home directory of my rails app. If I go into a sub directory in my rails app, or any other directory on my machine, the tab complete works again. If I go into the root directory of any other rails app, it works. I also tried renaming the diretory, and copying the contents of the directory to another directory, and that did not work either. It only does not work for files, and works for any other command - ls, rm etc. But when I do vim /path/to/file/, then tab to see a list of files in that directory, only other directories show, not files. I am using ubuntu 12.04. Also, I tried re-installing vim, re-booting, removing ~/.viminfo (there was no vimrc file) that didn't work. Any help would be appreciated!

  Read the article

• lsof not showing what port a proc is listening on

  - by ericslaw

  I have many processes on a box listening on several ports. I am trying to map ports to pids. The problem is that lsof is not telling me what ports belong to which process. Given an apache listening on port 80, I can see it listening via netstat: user@host% netstat -an|grep LISTEN|grep 80 *.80 *.* 0 0 49152 0 LISTEN But when I try to map port 80 to a pid I get nothing: user@host% lsof -iTCP:80 -t When I try seeing what sockets that specific pid is using I get: user@host% lsof -lnP -p31 -a -i COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME libhttpd. 31 0 15u IPv4 0x6002d970b80 0t0 TCP *:65535 (LISTEN) Notice the *:65535 in the NAME column. Does anyone know why lsof is not reporting the port in use? I am running as root. I am using a mix of lsof and os versions: lsof v4.77 on Solaris10 sparc lsof v4.72 on Redhat4.2 etc I know that linux solutions can use "netstat -p", so I guess I'm only looking for why solaris isn't working, but I find lsof is frequently silent and not showing me expected data.

  Read the article

• Port 22 is not responding

  - by Emanuele Feliziani

  I'm trying to make the jump to VPS from shared hosting for better performances and greater flexibility, but am stuck with the fact that I can't access the machine via ssh. First of all, the machine is a CentOS 6.3 cPanel x64 with WHM 11.38.0. Sshd is running (it appears in the current running processes). Making a port scan I see that port 22 is not responding. Port 21 is, but I am not able to access the machine via ftp (I think it's a security measure, but I don't know where to disable/enable it). So, I'm stuck in WHM and have no way to access the configuration of the machine, neither via ssh nor with ftp/sftp. When trying to connect with ssh via Terminal I only get this: ssh: connect to host xx.xx.xxx.xxx port 22: Operation timed out I also tried to access with the hostname instead of the IP address and it's the same. There seem to be no firewall in WHM and I have whitelisted my home IP address to access ssh, though there were no restrictions in the first place. I have been wandering through all the settings and options in WHM for several hours now, but can't seem to find anything. Does anybody have a clue as to where I should start investigating? Update: Thanks everyone. It was in fact a matter of firewall. There was a firewall not controlled by the WHM software. I managed to crack into the console from the vps control panel (a terrible, terrible java app that barely took my keyboard input) and disabled the firewall altogether running service iptables stop so that I was able to access the console via ssh with the terminal. Now I will have to set up the firewall again because the command I ran looks like having completely wiped the iptables. Can you recommend any newby-friendly resource where I can learn how to go about this and what should I block? Or should I just go with something like this: http://configserver.com/cp/csf.html ? Thanks again to everyone who helped me out.

  Read the article

• SSD/HDD not exceeding 120 MB/s

  - by skiwi

  SO here is the situation: First this was my old PC, it had a 2x 1TB RAID 0 and a Corsair Force 3 SSD in it. This were the old speeds, measured by HDTune Pro. 2x 1TB RAID 0: Corsair Force 3 SSD Then my dad got my PC and we had several issues, in the end turned out both RAID and SSD controller were malfunctioning causing BlueScreens on 100% load. Removed the RAID 0, but leaving the HDD's intact and bought an Samsung 840 EVO 120GB, though the Corsair SSD is still in the system, just not as sytem disk anymore. 1TB HDD (one of them): Corsair SSD: Samsung SSD: We did not assemble the PC ourselves, so answering some technical questions might be more difficult, though we will do our best. First thing we noticed is that the Samsung 840 EVO is no where reaching it's advertised speed, even an Samsung 840 250GB (non-EVO) is reaching 350 MB/s in my own PC. Then we noticed that both SSD's are capped at 120 MB/s exactly, not sure if this is being caused by HDTune Pro, but very unlikely. And even worse, the Corsair Forza 3 was running faster before the system got reassembled. Does anyone have any clue what is going on?

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• GNU Screen and Finch Not Playing Nicely

  - by Sean M

  I use finch for instant messaging, and for persistence, finch is one of the things that runs in my screen session. There are three main computers that I access my screen session from, and each works at a different screen resolution. Because of the different resolutions, when I switch computers, I use screen -rd to attach to my screen session. Using screen -x results in problems. When I attach to the session, though, finch experiences display problems. I have to wait up to several minutes for finch to become responsive - it doesn't redraw properly at all. Trying to switch between chats just writes ^n and ^p, or ^(1-9) for numbers. It fixes itself after some time. Using ctrl-l does not help. Switching back and forth between screen windows does not help. This is an annoying behavior that I don't experience with any other applications running in screen. Is this a bug in screen or finch, and if not, what can I change about my configuration to correct it ? (would appreciate it if "finch" could be used as a tag for this instead of or in addition to "pidgin")

  Read the article

• Not getting IP from ISP on Multicast Network

  - by Johan Nielsen

  Im having an odd issue with my ISP (COMX.dk) I have a managed access gateway box (Telsay) with three 8P8C ports for use with Internet and Ip-Tv (respectively on different VLANS (so does my ISP tell me)) To utilize a port you will need to register your device's mac address through an online interface. You will then get your device paired with a static ip. I am using one port actively and I have registered another device (router). The router is configured to listen for an active dhcpd on the network. When my router get a lease I get a private ip 192.168.2.2 (not the one bound to my mac) which is odd! I unconnected my router from the gateway and connected my laptop directly. Same thing happened - I was given a private address. I did a port scan on the gateway and found port 80 to be open and browsed to the ip. I was then presented with a management interface of a Belkin wireless router (HMMM!!!!) <--by the way, not my gear At this point I called the ISP to let them know of my issue/findings - Only to be replied "Well, we cant see any rogue dhcp servers" (thinking to myself, well I can) I then decided that it could be fun to try the other port of my gateway, only to experience the same. So I reconnected my router and used the remaining port to make an observer(wireshark promic etc.) I am able to see my router trying to discover a dhcp server but I can also see my ISP's IGMP and PIMv2 packages just repeating the same pattern. Hello...Hello...Hello :) So I called them again, only to get the same response, "we dont see any rogue dhcp's...we cant see the host you are talking to (mac address of the Belkin router)...you are definitively connected through wireless?!?(no im not, no such thing as a wireless wire - i thought to myself)" My questions is, What is going on? (besides from what im reporting here) What am I seeing that the don't? What can I tell them in order for them to resolve mine/their issue?

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• USB Harddisk not working on dual boot windows7/8

  - by Jesper

  Yesterday I installed Windows 8 on a machine that already had Windows 7. They are on dual boot and both systems work fine. The problem is that inserting a USB hard disk in either system does nothing. If I connect a USB mouse or mobile phone, they work fine, so the USB plugs are active/working and the USB hard drives that I am trying to connect work on my other laptop just fine. I have tried to uninstall all USB-related items in Device Manager and let them reinstall upon restart, but that didn't help. The USB drive does not show up in disk management either. The strange thing is that it is exactly the same situation on both windows. USB mice etc. work just fine and USB hard drives do not. Any ideas on solving this problem would be great. ...Don't know if it is important, but this is a Toshiba Tecra R950 Laptop. EDIT: I have found out that my other USB HD (Western Digital) works on this laptop, but for my StoreJet Transcend and Adata "something" does not work. All three work on another Windows 7 laptop. Sizewise the WD is in the middle at 400 GB. The StoreJet is 640 GB and the Adata is 200 GB.

  Read the article

< Previous Page | 138 139 140 141 142 143 144 145 146 147 148 149  | Next Page >