Search Results

Search found 11687 results on 468 pages for 'ex networking guy'.

Page 144/468 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

• debian 6 losing a large amount of packets

  - by Sc0rian

  I have a rather strange problem. We covered all the obvious hardware related issues (different nic, eth cable and switch) however I cannot seem to stop eth dropping packets. I have 4 servers all exactly the same. driver: e1000e version: 1.2.20-k2 firmware-version: 1.8-0 bus-info: 0000:06:00.0 They are all running the latest kernel(2.6.32-5-amd64). However they do this: RX packets:17073870634 errors:0 dropped:14147208 overruns:0 frame:0 another server: eth0 Link encap:Ethernet HWaddr e0:69:95:05:2f:cb inet addr:10.10.10.86 Bcast:10.10.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5455209277 errors:0 dropped:375445 overruns:0 frame:0 TX packets:3666134366 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6688414486673 (6.0 TiB) TX bytes:1611812171539 (1.4 TiB) Interrupt:20 Memory:d0600000-d0620000 eth1 Link encap:Ethernet HWaddr 00:1b:21:b7:7a:ce inet addr:10.10.0.86 Bcast:10.10.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15473695728 errors:0 dropped:5808325 overruns:0 frame:0 TX packets:20112364421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9192378766434 (8.3 TiB) TX bytes:20216368266761 (18.3 TiB) Interrupt:17 Memory:d0280000-d02a0000 A massive amount of dropped packets. I have tried to load on the latest driver, 1.9.5. This did nothing. I'm not sure what else to do.

  Read the article

• Why isn't 'ether proto \ip host host' a legal tcpdump expression?

  - by Ezequiel Garzon

  In its description of valid tcpdump expressions, the pcap-filter man pages state: The filter expression consists of one or more primitives. Primitives usually consist of an id (name or number) preceded by one or more qualifiers. In turn, these qualifiers are type, dir and proto. So far so good, but further down we find this: ip host host which is equivalent to: ether proto \ip and host host In the first case, ip and host are, respectively, proto and type. What pattern does ether proto \ip follow? Isn't that, as a whole, a proto qualifier? If so, why isn't (a properly escaped) 'ether proto \ip host host' legal (no and)?

  Read the article

• How do I network this Windows Failover Cluster and MongoDB Replica Set? (diagram inside)

  - by arex1337

  As you can see, my two Windows Server Failover Cluster (WSFC) nodes have three network interfaces each, which connects them to three different networks : A public network A private network consisting of the WSFC nodes A private network consisting of the WSFC nodes and a machine with the WSFC Quorum Witness File Share Does this network configuration I've planned, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. My two MongoDB Replica Set nodes also have three network interfaces each - very similar to the previous situation: A public network A private network consisting of the primary and secondary MongoDB Replica Set nodes A private network consisting of the primary, secondary and arbiter MongoDB Replica Set nodes Does this network configuration, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. Here is the simpler version I'm considering: UPDATE:

  Read the article

• Multiple virtual VLAN interfaces on single NIC (Debian)

  - by RayQuang

  I'm trying to setup multiple virtual interfaces with VLAN's on a single NIC. I'm running Debian Squeeze. Currently this is my /etc/netowrk/interfaces auto eth0.10 iface eth0.10 inet dhcp This gives me a working connection, however I'm not sure how to configure several like these on a single NIC so I can use multiple external IP's. I have tried aliasing the VLAN's like so: iface eth0.10:1 But that was not successful and it said failed to bring up interface. And suggestions would be greatly appreciated :)

  Read the article

• Unable to connect to Windows VPN from iPad

  - by Justin

  I have a 16 GB iPad wifi I can't get to connect to VPN. The error I get is: "A connection could not be established to the PP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator." I have tried a variety of tasks to troubleshoot the issue: I have verified that another iPad on another network can connect to the VPN I am trying to connect to I can connect to this VPN from the same network the iPad uses on a Windows machine I have verified an iPhone user can connect to this VPN from a different network I have reset the iPad's network settings I have reset the entire iPad and restored settings I have compared my settings w/ a screenshot from the iPad that works and confirmed everything is correct I have used the IP address and domain name of our VPN server in the settings I have tried deleting the VPN settings in the iPad and recreating them I have verified in the logs of VPN server that I'm not even getting to the VPN server (no log entry) I have verified that I cannot VPN from the iPad on separate network (different ISP and router) Are there any other ways to troubleshoot VPN on an iPad?

  Read the article

• Mac OS X: pushing all traffic through a VMWare VM

  - by bj99

  I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

  Read the article

• I need a reverse proxy solution for SSH

  - by Bond

  Hi here is a situation I have a server in a corporate data center for a project. I have an SSH access to this machine at port 22.There are some virtual machines running on this server and then at the back of every thing many other Operating systems are working. Now Since I am behind the data centers firewall my supervisor asked me if I can do some thing by which I can give many people on Internet access to these virtual machines directly. I know if I were allowed to get traffic on port other than 22 then I can do a port forwarding. But since I am not allowed this so what can be a solution in this case. The people who would like to connect might be complete idiots.Who may be happy just by opening putty at their machines or may be even filezilla.I have configured an Apache Reverse Proxy for redirecting the Internet traffic to the virtual machines on these hosts.But I am not clear as for SSH what can I do.So is there some thing equivalent to an Apache Reverse Proxy which can do similar work for SSH in this situation. I do not have firewall in my hands or any port other than 22 open and in fact even if I request they wont allow to open.2 times SSH is not some thing that my supervisor wants.

  Read the article

• Slow LAN transfer from 3rd party computer

  - by Chris

  Hi Everyone, I've got an odd problem that I'm not really sure where to start the troubleshooting process. I have a 'server' with Windows Server 2008R2 (64-bit) installed and it has a couple of hard drives. If I Remote Desktop into the server and transfer files from one HD to the other, all it fine. If however, I use my workstation (Windows 7 64bit) and open up a shared resource on the server and transfer a file from one hard drive on the server to another HD on the server (not using Remote Desktop, just Windows explorer/Network places), the transfer crawls... It takes about 5mins to discover files/calculate the transfer and then starts transferring at speeds like 56KB/s - 200KB/s. Both machines have Marvel GigE network ports with a TrendNet 8-port green GigE switch. I've set Jumbo packets to 9K on both machines...

  Read the article

• Not able to access the server after changing the password?

  - by cyrilsebastian

  While accessing the server, the error comes: Multiple connections to a server or shared resource by the same user, using more than one user name, are not allowed. Disconnect all previous connections to the server or shared resource and try again. I am logging in from Administrator in XP machine, able to access server from other machines. Is there any problem with administrator profile??

  Read the article

• How to troubleshoot slow powerconnect 62xx management interface

  - by Hannes

  Our Dell Powerconnect 62xx switches have a very high packetloss on the management interface. I presume this is caused by a new appliance which uses multicast for communication but I am not sure. Our network setup is following: servers a - Dell PC6248 | servers b - Dell PC6248 |- juniper core router servers c - Dell PC6248 | What we see is that the multicast traffic arrives at all servers (but only the servers b use the multicast) and I fear that this multicast traffic floods the switch management interface. The switches' management interfaces are reachable via vlan101, all other traffic is sent over other vlans. When I tcpdump on one of the 2 servers with a vlan 101 ip address, I only get a few arp requests but almost nothing. When I try to ping between these 2 servers, it works like a charm. I would like to know what a good way is to troubleshoot this problem and maybe help me understand what is going wrong on that subnet.

  Read the article

• How to create a separated network to customers only?

  - by Valter Henrique

  I work in a company where we have a network ethernet and wi-fi, we would like to create a network where our customers could access our network but don't have access to our computer network. This access would be internet only, nothing more. The customers will not see our computers and the files that we share in our network. I have two routers, how can I do this ? A Cisco Linksys Wireless-N Broadband Router WRT160N V3 and a Netgear Wireless G Router WGR614 v9 and about firewalls there´s only windows firewalls in each computer by default.

  Read the article

• Dynamic DNS on D-Link DWR-112 3G router uses a private IP address

  - by user270151

  I'm using a D-Link DWR-112 3G router to connect to the internet by using Celcom broadband plug-in. How can I do the port forwarding to my server? I already have correctly configured my DynDNS, but every time the DynDNS will not set to public address but local private address with in the range 10.xxx.xxx.xxx. My router address is 192.168.1.1 and server address is 192.168.1.5. Can someone give me some guideline about this issue?

  Read the article

• how to reinstall the TCP IP protocol driver on windows 7 ?

  - by Revolter

  how to reinstall the tcp/ip protocol driver on windows7 ?

  Read the article

• How to disable ipv6 on MacOS and never see an address resolved to ipv6

  - by shabunc

  On MacOS (10.8.5 if that matters) I'm trying to disable off ipv6 via networksetup -setv6off Wi-Fi. Nevertheless, when I'm trying to wget a specific files URL resolves to ipv6 address and download fails. I just wonder what I am missing in order not to feel as stupid as I currently feel. ifconfig shows that some of interfaces have inet6 enabled, but I just don't know whether this is relevant at all. networksetup -listallnetworkservices does not show anything extraordinary I've forgot about.

  Read the article

• Simulating network latency for localhost connection on Windows 7

  - by nitro2k01

  I need to simulate network latency to a program running on the local computer, connecting to a local service. Thus far I have tried dummynet (a windows build of ipfw) which I got working after some trial and error. While it generally works, I can't seem to get it to filter localhost traffic. Even after adding a rule from any to any which affects external traffic, this makes no difference for local connections. I would appreciate if anyone knows how to simulate local latency using dummynet or a different tool. The tool should be able to simulate latency generically in IP packets, (TCP and UDP) and not be protocol specific.

  Read the article

• PowerConnect 3548p SNTP and web interface not working

  - by Force Flow

  I have been unable to get SNTP and access to the web interface working properly on a Dell PowerConnect 3548p. In the logs, this message appears over and over again: 04-Jan-2000 20:19:29 :%MNGINF-W-ACL: Management ACL drop packet received on interface Vlan 172 from 172.17.0.3 to 172.18.0.10 protocol 17 service Snmp 172 is the management vlan. 172.17.0.3 is the DNS server 172.18.0.10 is the switch's IP address. The DNS server and the switch are located on different subnets and separated by routers. I am unable to access the web interface of the switch from the 172.17.x.x subnet. I can only access the web interface of the switch if I am accessing it from the 172.18.x.x subnet. There is also a managed linksys switch on the 172.18.x.x subnet on the 172 vlan, which has no problem with SNTP. I can also access it from the 172.17.x.x network. So, it stands to reason that this is not a firewall or routing issue, but with the 3548p switch. I suspect the issue is with management permissions/ACLs on the 3348p switch, but that's about as much as I've been able to determine so far. Any ideas?

  Read the article

• Extending a home wireless network using two routers running tomato

  - by jalperin

  I have two Asus RT-N16 routers each flashed with Tomato (actually Tomato USB). UPSTAIRS: Router 'A' (located upstairs) is connected to the internet via the WAN port and connected via a LAN port to a 10/100/1000 switch (Switch A). Several desktops are also attached to Switch A. Router A uses IP 192.168.1.1. DOWNSTAIRS: I've just acquired Router 'B' and set it to IP 192.168.1.2. I have a cable running from Switch A downstairs to another switch (Switch B). Tivo, a blu-ray player and a Mac are connected to Switch B. My plan was to connect Router B to Switch B so that I have improved wireless access downstairs. (The wireless signal from Router A gets weak downstairs in a number of locations.) How should I configure Router B so that all devices in the house can see and talk to one another? I know that I need to change DHCP on Router B so that it doesn't cover the same range as DHCP on Router A. Should I be using WDS on the two routers, or is that unnecessary since I already have a wired connection between the two routers? Any other thoughts or suggestions? Thanks! --Jeff

  Read the article

• Only 192.168.0.3 can request most files, but anyone can request /public/file.html

  - by mattalexx

  I have the following virtual host on my development server: <VirtualHost *:80> ServerName example.com DocumentRoot /srv/web/example.com/pub <Directory /srv/web/example.com/pub> Order Deny,Allow Deny from all Allow from 192.168.0.3 </Directory> </VirtualHost> The Allow from 192.168.0.3 part is to only allow requests from my workstation machine. I want to tweak this to allow anyone to request a certain URL: http://example.com/public/file.html How do I change this to allow /public/file.html requests to get through from anyone? Note: /public/file.html doesn't actually exist as a file on the server. I redirect all incoming requests through a single index file using mod_rewrite.

  Read the article

• Presentation software requires admin rights to install - any way to remove this requirement?

  - by James F

  I have some wireless presentation software which I use in a meeting room in order to allow end users to hold presentations here and wirelessly have their laptop screens showing on the TV on the wall. Unfortunately the .exe file requires admin rights to install therefore requiring that either the user requests temporary admin rights beforehand, I install it using my admin account or that we use a VGA/HDMI cable. Is there a way to remove the admin right requirement from a .exe or a .msi file so that it can be installed freely by any user? We are using XP for now but will be moving to 7 soon. Thanks James

  Read the article

• Switch flooding when bonding interfaces in Linux

  - by John Philips

  +--------+ | Host A | +----+---+ | eth0 (AA:AA:AA:AA:AA:AA) | | +----+-----+ | Switch 1 | (layer2/3) +----+-----+ | +----+-----+ | Switch 2 | +----+-----+ | +----------+----------+ +-------------------------+ Switch 3 +-------------------------+ | +----+-----------+----+ | | | | | | | | | | eth0 (B0:B0:B0:B0:B0:B0) | | eth4 (B4:B4:B4:B4:B4:B4) | | +----+-----------+----+ | | | Host B | | | +----+-----------+----+ | | eth1 (B1:B1:B1:B1:B1:B1) | | eth5 (B5:B5:B5:B5:B5:B5) | | | | | | | | | +------------------------------+ +------------------------------+ Topology overview Host A has a single NIC. Host B has four NICs which are bonded using the balance-alb mode. Both hosts run RHEL 6.0, and both are on the same IPv4 subnet. Traffic analysis Host A is sending data to Host B using some SQL database application. Traffic from Host A to Host B: The source int/MAC is eth0/AA:AA:AA:AA:AA:AA, the destination int/MAC is eth5/B5:B5:B5:B5:B5:B5. Traffic from Host B to Host A: The source int/MAC is eth0/B0:B0:B0:B0:B0:B0, the destination int/MAC is eth0/AA:AA:AA:AA:AA:AA. Once the TCP connection has been established, Host B sends no further frames out eth5. The MAC address of eth5 expires from the bridge tables of both Switch 1 & Switch 2. Switch 1 continues to receive frames from Host A which are destined for B5:B5:B5:B5:B5:B5. Because Switch 1 and Switch 2 no longer have bridge table entries for B5:B5:B5:B5:B5:B5, they flood the frames out all ports on the same VLAN (except for the one it came in on, of course). Reproduce If you ping Host B from a workstation which is connected to either Switch 1 or 2, B5:B5:B5:B5:B5:B5 re-enters the bridge tables and the flooding stops. After five minutes (the default bridge table timeout), flooding resumes. Question It is clear that on Host B, frames arrive on eth5 and exit out eth0. This seems ok as that's what the Linux bonding algorithm is designed to do - balance incoming and outgoing traffic. But since the switch stops receiving frames with the source MAC of eth5, it gets timed out of the bridge table, resulting in flooding. Is this normal? Why aren't any more frames originating from eth5? Is it because there is simply no other traffic going on (the only connection is a single large data transfer from Host A)? I've researched this for a long time and haven't found an answer. Documentation states that no switch changes are necessary when using mode 6 of the Linux interface bonding (balance-alb). Is this behavior occurring because Host B doesn't send any further packets out of eth5, whereas in normal circumstances it's expected that it would? One solution is to setup a cron job which pings Host B to keep the bridge table entries from timing out, but that seems like a dirty hack.

  Read the article

• How can I print from my lion mac mini to my windows XP, with simple file sharing?

  - by Jules

  I have quite a complicated setup, perhaps. And a lot of history on this issue, I'm hoping that I don't have to buy a new printer. I've got a HP Wireless USB Print Server, which requires client software, I can't just use it as an IP Printer. The HP software is pretty poor on the mac and is no longer supported and often locks up the printer server and takes some considerable effort to actually print something. Let alone if a windows machine attaches to it first. My printer is an Epson Stylus R285. However, the windows client software is fine and we can print from windows 7 / XP without problem. We have simple file sharing setup as this is the only way I could get windows XP to talk to windows 7. However, I can't seem to get my mac mini to connect as anything other than a guest to my xp machine, to connect to the shared printer. I'm not considering some kind of internet printing as this would seems the simplest solution. But I'm not sure what will work with my setup ?

  Read the article

• Access node.js local server though mobile via same shared wifi

  - by laggingreflex

  EDIT: I was stuck in this situation before but then it was Apache-related But this time I'm using NodeJS, so the old answer doesn't help. I'm running apache a NodeJS webserver (on port 80) on Windows 7. I want to access the webserver through my mobile which shares the wifi router with my pc locally. http://localhost works from PC. But I can't access http://192.168.1.4 from either my phone or even my computer. ipconfig /all on my computer lists my ip address as 192.168.1.4 Wireless LAN adapter Wireless Network Connection: IPv4 Address. . . . . . . . . . . : 192.168.1.4(Preferred) I can ping my phone's (internal) ip address [192.168.1.5] from PC and vice-versa, I can ping my PC [192.168.1.4] from my phone. So why can't I access http://192.168.1.4 from my phone? (or PC) Firewall is off.

  Read the article

• Router drops internet connection if I connect an additional pc

  - by BluePerry

  Hey, I'm using a SMC2804WBRP-G router connected to my ADSL-modem. Usually there are two computers connected to this router: a win7 ultimate desktop(wired) and a macbook air (wireless). Both working absolutely fine and never caused any connection drops as far as I know. A new room mate moved in last month and each time she starts up her win7 home laptop the router looses the internet connection. The laptop is on a wired connection. The first time she connected to my router, the connection dropped every 2 mins. To find out whats wrong with her machine I disabled all unnecessary services etc. besides the anti virus software. That helped to eliminate almost all of those periodic connection drops. But the start up drop remained and I've got the feeling that the router is still loosing connection from time to time. I haven't had the time to find out what service caused the periodic drops. But I'm more concerned about is that start up drop. Can anyone point me in the right direction to look for the problem? I would be very thankful for any hints or tips!

  Read the article

• Choosing a home network layout

  - by James M.

  I have a server, 4 PC's, a network printer, a switch and an ADSL modem. Currently the server runs Red Hat 9 and sits between the internet and the other PCs like in http://upload.wikimedia.org/wikipedia/en/1/12/Sample-network-diagram.png I have bought a new server PC to replace the old one, and I plan to install Fedora Core linux on it. The server acts as web and file server. The PCs all run Windows. Alternatively, I could connect the new server and all PCs to the switch, and connect the switch to the modem. (Sorry, couldn't find an image.) What are the pros and cons of these network layouts? Eg. in terms of reliability, security and flexibility? I am not a Linux guru but know of (and am not afraid of) iptables, dhcpd et al. Thank you for any tips, pointers and links.

  Read the article

• Flow of packet in network

  - by user58859

  I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN. When packet goes from router to local LAN, do it passes all the computers? Means did it goes to ehernet card of every computer and those computers accept the packet based on their physical address. To which pc the packet will go first? To the nearest to the router? What happen if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this? Thanks in advance.

  Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >