Search Results

Search found 4762 results on 191 pages for 'ref cursor'.

Page 144/191 | < Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >

• Why can't I boot in to Windows Recovery Environment to fix my HDD or salvage my data?

  - by Kevin

  I've been trying to get in to WindowsRE to salvage the files on my Sony Vaio laptop after it failed to load Vista (it finally, consistently displays "Error loading operating system" after months of such intermittent failures, usually rectified via restarts or utilizing Startup Repair or CHKDSK from WindowsRE) . The problem is, after successfully accessing it once after this failure (and many times before over the course of the laptop's life), I can no longer get it to load. During the last successful access (right after the failure), I ran startup repair, which itself failed and notified me that the boot sector was corrupt. I attempted to head in to Sony's proprietary recovery tools menu, which is accessible from WindowsRE when it is loaded from the recovery partition or recovery disk, however it hung. I have since been unable to access the recovery environment after restarting, using any of these methods: Access via the recovery partition (pressing F10 on boot) Access via recovery DVD (created using the same computer when it was healthy) Access via a Windows Vista installation DVD All three methods produce the same results: The computer acknowledges the boot attempt The computer successfully gets passed the "Windows is loading files" screen The computer successfully gets passed the Windows loading screen The computer then stalls at a black screen, while showing HDD activity (via indicator light). After a few minutes, the HDD activity ceases, and after a few more minutes, the over sized cursor that is utilized in WindowsRE appears on the black screen. The actual recovery environment, however, never appears, even after leaving the computer in such a state overnight. What is fustrating is that other bootable utilities, such as SeaTools for DOS and MemTest, boot up and run fine. In running perfectly normally, MemTest was able to produce a plethora of errors utilizing my RAM. I'm inclined to believe the RAM's faultiness may causing the WindowsRE booting to fail. Would this be a valid assumption? If I'm not mistaken, booting from external media utilizes the RAM, so such a reason is plausible, assuming my knowledge of bootloading is correct. Other than that, I can't figure out any reason why all the bootable utilities except WindowsRE run fine. Does anyone know what the problem is, or could be? Any solutions?

  Read the article

• What would cause my Windows machine to seize?

  - by Coltin

  I run Windows XP SP2 on a Desktop I built (I know that doesn't provide much, but I can't say "on a Dell X103938R" or something). It has 'seized' about 7 times in its year and a half life. Everything freezes. I can't move the mouse cursor and the keyboard seems unresponsive. I can turn the monitor on and off and it will hold the last image. The light for the mouse is responsive if I move it. The keyboard lights change when pressed (cap locks, etc). I've waited upto ten minutes for a change, nothing. I haven't connected any activity to the seizing. It's happened when all I was "running" were fullscreen programs (games), just checking email, or once when I was sitting at my desktop (I was reading a book and when I tried to use the mouse, nothing). I've never been able to figure it out. I have to hard reset, and then its fine. It doesn't file system check or anything (not sure if Windows does that). No error when I load up the computer, nothing. If I had uTorrent open, it will have to recheck the torrent files to make sure they weren't corrupted though. (It's not always open when it seizes either). I'm using an AMD Athlon 5400+ with a NVidia GeForce 8600 GT, if that helps. I'm using two hard drives, 500Gb Wester Digital with a 1Tb Hitachi.

  Read the article

• Why am I unable to reach local network computers, but able to browse the web?

  - by Igor Zinov'yev

  I have a weird problem. Today after turning my Ubuntu 9.10 PC on I can't connect to my local network, but I can use the Internet. We have a single Windows 2003 server machine that acts as a local main DNS server, DHCP server and a domain controller. Although it seems to give me the local IP address, I can not ping it, as well as any other machine on the net. I have tried all of the below and it didn't help: Rebooting; Reconnecting to the network; Forcing the dhclient to renew the IP address; Deleting and creating new connection profiles; Plugging my machine into another network outlet; Maybe it has something to do with routing, because I have tampered with routing tables the day before, but the tables seem ok to me: $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 0.0.0.0 255.255.255.0 U 1 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 vboxnet0 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 Our LAN uses a D-Link DI-604 router, and it looks to me as if I am connected to the network outside the router. I can not even access its administration page. Please at least suggest what I can do to solve this. P.S. What seems strangest to me is that I can access the PC in question from outside the network by opening a port on the router. I have managed to ssh to it from outside, but I still can't ping nothing on the inside. P.P.S Today I tried reinstalling network-manager with --purge option, but it did no good. After that I created a new DCHP reservation for my PC in order to change my local IP, but that didn't change anything either. My PC is able to get a DHCP offer, but then it's unable to connect to any local computers. I am desperate.

  Read the article

• X.org - mouse gets stuck on press

  - by grawity

  I'm using Arch Linux. Very often, when I click on something, the OS thing sees the mouse press but not the release. If it was a link or file I clicked, moving the cursor would drag it too. Hammering the same mouse button again gives no effect. Usually, if I tap the touchpad (ALPS), the system finally sees both press and release of that, and I can continue working. (This might be because it uses a different driver - synaptics instead of evdev.) As you can imagine, this is quite annoying even for someone who spends 70% of his life in front of a terminal app. This is not a mouse issue - I'm on a laptop, and this affects both the Trackpoint thing and an external USB mouse. This is not a DE or window manager issue - I have used GNOME (with Metacity, Compiz and Xfwm4), Xfce (with Metacity and Xfwm4), mwm, twm, awesome, and wmii. Doesn't seem to be a hardware thing - after rebooting into Windows XP, everything works fine. hal is used for the auto-configuration of devices (as I have to disconnect the USB mouse often), so Xorg.conf really has nothing of relevance. Xorg -version shows: X.Org X Server 1.6.3.901 (1.6.4 RC 1) Release Date: 2009-8-25 X Protocol Version 11, Revision 0 If it changes anything, the laptop is stone-age Dell Latitude C840. I kinda suspect either hal or the evdev thing to cause it, but I really have no ideas on what to check further. In other words, HALP!#$ This thing is driving me nuts.

  Read the article

• Allow opening a new tab with Ctrl+T on all websites in Firefox

  - by Martin J.H.

  In Firefox, certain websites and plugins (Adobe PDF Plugin) appear to "capture" the Control key, so that when I try to open a new tab using "Ctrl+t", nothing happens - or worse, something unexpected happens. Examples: On the Codecademy site, while editing code, Ctrl+T either does nothing, or (when Flash is disabled) switches the position of the two characters next to the cursor. When viewing PDF's with the Adobe PDF Plugin, Ctrl+T does nothing. Is there a way to disable this "feature"? I would like "Ctrl+t" to always "talk" to Firefox! Edit: After searching superuser deeper, this question is very similar to the questions: "How to prevent keystroke grabbing/hijacking by websites in Firefox?" "How do I prevent pages I visit from overriding selected Firefox shortcut keys?". The answers to these questions are interesting and relevant, but do not give a method on how to disable combinatinos such as "Ctrl+t". Maybe a modified Greasemonkey script is the easiest solultion. Edit 2 - Attempt at a solution The following UserScript (Use GreaseMonkey to install it) successfully captures Ctrl+t on some sites (Google Search site, for instance - PopUp "Gotcha" appears), but not on the Codecademy site. I found another question pertaining to this subject here: "How to forbid keyboard shortcut stealing by websites in Firefox". It was raised in 2010, and the consensus was: It can't be done. // ==UserScript== // @name Disable Ctrl T interceptions // @description Stop websites from highjacking keyboard shortcuts // // @run-at document-start // @include * // @grant none // ==/UserScript== // Keycode for 't'. Add more to disable other ctrl+X interceptions keycodes = [84]; var lastPressedButton = [0]; document.addEventListener('keydown', function(e) { //uncomment to find out the keycode for any given key // alert(e.keyCode ); if (keycodes.indexOf(e.keyCode) != -1 && e.ctrlKey) { e.cancelBubble = true; e.stopImmediatePropagation(); alert("Gotcha!"); } return false; });

  Read the article

• Does the Lenovo t60p vga port support an s-video signal?

  - by Matthijs Wessels

  I just bought a new television. The problem is it turns out it doesn't have a VGA port. It does have: s-video, component, hdmi and scart. My Lenovo t60p only has vga. If have search frantically for a solution and even though it seems I have sooo many options they are all dead ends. Or I keep ending up having to buy a 100 euro box to convert the signal. However, I found that some video cards support s-video through the vga port. It says look it up in your video cards documentation. I have a Lenovo t60p laptop with a ATI MOBILITY FireGl v5250. But I can't seem to get my hands on any documentation where this is supposed to be documented. I found this website: http://forum.notebookreview.com/showthread.php?t=179529&highlight=s-video There this guy says he thinks it's in the t60 but dropped in the t61, but suggests to the guy with the t60 that it won't work. I can't really conclude anything from that. Furthermore, I am not looking for the best of the best quality. So when I found this: *http://www.amazon.com/VideoSecu-Computor-Presentation-Converter-VGA2TV/dp/B000X3FAJU/ref=pd_cp_e_3_img I woudl be quite happy with this. Except that I don't think I can order it because I don't live in the US. Can anybody give me a definite answer, to whether the vga port of my lenovo t60p ati firegl v5250 supports s-video? So that I can just by a vga to s-video cable to achieve my goal.

  Read the article

• Change OpenVZ route to pass through ip failover

  - by Kevin Campion

  I have one dedicaced server with its own IP and another IP (failover) who refer to the first. I will wish to change the gateway of a Proxmox virtual machine (openvz) who runs on this dedicaced server to go through the failover IP rather than the ip of host main server. Once connected to a virtual machine, when I do a traceroute VE# traceroute www.google.fr traceroute to www.google.fr (209.85.229.104), 30 hops max, 60 byte packets 1 MY_SERVER_NAME.ovh.net (xxx.xxx.xxx.xxx FIRST_IP_MAIN_SERVER) 0.021 ms 0.010 ms 0.009 ms The first line tells me the ip of host main server. I would like that the traceroute display the second IP failover. VE# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 * 255.255.255.255 UH 0 0 0 venet0 default 192.0.2.1 0.0.0.0 UG 0 0 0 venet0 With iptables HOST# iptables -t nat -L Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- anywhere anywhere MASQUERADE all -- anywhere anywhere SNAT tcp -- anywhere 10.10.101.2 tcp dpt:www state NEW,RELATED,ESTABLISHED,UNTRACKED to:SECOND_IP_FAILOVER SNAT all -- 10.10.101.2 anywhere to:SECOND_IP_FAILOVER 10.10.101.2 is the virtual machine IP (interface venet0) Any ideas ?

  Read the article

• Converting An Older VMWare Image to ESXi

  - by Bart Silverstrim

  I have just installed VMWare ESXi and imported one physical machine without issue and one virtual machine, from an older version of VMWare Server on a Linux system, to it without issue. But I have another machine (Windows XP), virtual running on the VMWare Server, that I can't get the Converter to work with. Converter runs, says everything is fine, but when I go to the ESXi VSphere manager and hit the button to power up that vm, the console stays black with a blinking cursor and the processor for that VM spikes 100% and stays there. An event log item in VSphere warns something about activation issues with Windows. Has anyone else run into this issue before? Is it something with the disk controller? I copied the folder with the VM directly to the storage drive on ESXi hoping to create a new machine and point the data store to that folder or at least that drive image; nope, something about not using an IDE controller (must be something with the older format). In short, converter is doing something that particular machine doesn't like, and I can't find a way to simply open that hard disk image or convert it unless someone else has seen this. I try attaching a bootable CD image for disk repair to see if it can check the hard drive but I can't seem to get the console to boot from it...either too slow on the button or it just isn't able to easily boot from a virtual drive image (.iso). Any suggestions or help?

  Read the article

• MS Word 2010: Hide citation title when 2 publications by same first author from different years are in one citation block

  - by srunni

  I'm trying to hide the display of the titles for two publications by the same first author from different years that are in the same citation block. By default, the title is shown in citations when there are two publications by the same author in a given document. The easiest way to get around this is to right click on the citation, click "Edit Citation", and then suppress the title. However, the issue with this is that if there are 2 citations in 1 citation block (i.e., "(Smith, J., et al. 2010, Smith, J., et al. 2011)" rather than "(Smith, J., et al. 2010) (Smith, J., et al. 2011)"), then using that suppress option only suppresses the title for the first citation (in this case, the 2010 publication). OTOH, if I try to initially insert the publications in separate citation blocks, I can suppress the title in both citations, but I can't cut and paste one into the other's citation block. I can click "Cut" and the citation that was just cut disappears, but the "Paste" option is not available when my cursor is in the second citation block. Any ideas? Thanks!

  Read the article

• Scroll wheel causes browsers + Windows explorer to go back

  - by KaptajnKold

  I use Windows 7 on a VirtualBox VM on a Mac. Lately, when I'm using any browser (IE9, Chrome or FireFox or even Windows Explorer), use of the scroll wheel followed by any movement of the mouse cursor causes the browser to go back. Very annoying. This happens when I use the scroll wheel on a USB connected mouse (brand/model unknown, since I don't have it in front of me as I write this) or when I use two-finger scrolling on the trackpad when no mouse is connected. When I connect from my VM to a remote Windows box (Windows Server 2008), I experience the same problem. I have tried rebooting the VM to no avail. I am not sure when the problem started exactly. It may or may not have been after I connected the USB mouse for the first time, but trying to unplug it and then rebooting didn't help. I have tried to google for a solution, but all I've found are people who accidentally pressed the shift key while scrolling, which will cause the browser to go backward or forward in the browser history. This however is not the problem I'm having. To be clear, in my case the browser only goes back when I move the mouse after I've used the scroll wheel. I'm at my wits end :(

  Read the article

• My Boot order changed. Why?

  - by Chris

  I have a laptop running Windows XP SP3 with one internal hard drive partitioned into C: (system), D: (storage) and I have an external hard drive, F: (external drive). Yesterday the machine was running fine. Today, I go back to it and see that it's just showing a blinking cursor. Checked through the BIOS and the hard drive checked out fine. CTRL-ALT-DELETED the machine a few times, but I was never able to boot back into the operating system. I threw in a live CD and found out that the boot order of the drives has changed. The external drive is now C:, the system partiton is D:, and the storage partition is E:. Does anyone have any idea of how or why this would have occured? Auto system updates are turned off so there should have been no automatic reboot of the system overnight, and anti-virius runs on the machine and has found no infections before this occured. Edit When I was looking through the BIOS of the machine, I did see that the boot order was changed. But still the same question remains, what would have caused this to happen? I can't believe that a random reboot happened and totally changed my hard drive setup.

  Read the article

• Computer hangs at boot screen with new RAID card

  - by shanethehat

  I am trying to build a new server around a Biostar TH61 motherboard and an Adaptec 6405E RAID controller card. The machine booted fine from USB before the RAID card and drives were installed. After installing, on the first boot the card was detected, but then started to spit out the following message every 10 seconds: Error: Controller Kernel Stopped Running << Press any key to continue ... Following the troubleshooting guide I unplugged everything, reseated the card, and reattached all the drives. This time the machine is sitting on the boot screen without any error messages and flashing a cursor, but after 15 minutes of this, nothing seems to be happening. Given that there are no error messages I'm hesitant to reboot again. Is it normal for a RAID card to sit without a status message when it firsts boots, maybe to initialise the drives or something? The current screen output looks a bit like this: Controller #00 found at PCI Slot:01, Bus:01, Dev:00, Func:00 Controller Model: Adaptec 6405E Firmware Version: 5.2-0[18512] Memory Size: 128MB Serial number: 111111111111111 SAS WWN: 50000D1104AE9180 _ Update: So after waiting 30 minutes I've rebooted back to the Kernal Stopped Running error. Maybe time to update the RAID BIOS.

  Read the article

• Some guest networking and VMware Tools functionality broken with Sprint SmartView on the host

  - by Mads

  Using VMware Workstation 6.5.3 on Vista 64-bit. I started having problems with VMware networking about 6 months ago after upgrades to Sprint SmartView. I did not have problems previously, but I don't know if that is because I was lucky. The main symptoms of the problem when SmartView is installed are: I can no longer drag files from the host to copy them to the guest. When they are dragged, the disallowed cursor (the circle with a slash) shows in the guest. If I try to enable shared folders in the guest while it is running, I will not be able to see the shared files and will be informed that networking is not working. I can still ping guests from the host and I can still access network services via NAT most of the time when connected via my USB broadband adapter. When I configure shared folders so they are "always enabled" (with a mapped drive), I can access files on the via the mapped folders. I can also copy the file on the host and then paste it in the guest, as was suggested in some other threads concerning drag-and-drop problems that I found. The VMware Tools icon is showing in all cases and I don't see any obvious errors in the host's event viewer. If I uninstall SmartView, the problems disappear. If SmartView (current version is 2.28.0082) is reinstalled I will experience the same problems. I have tried uninstalling/reinstalling VMware and SmartView in various ways but it appears tha these problems are consistent when SmartView is installed (not just when it is running or connected, but when it is present on the system). I'm wondering if this is a combination of software (WS 6.5.3, Vista64, and SmartView) that works for other people, which would indicate a problem that is peculiar to my configuration.

  Read the article

• ISA 2000 and COD MW2 Steam

  - by twlichty

  OK, so maybe not the "proper use" of network resources, but we enjoy the odd COD game during lunch hours. When we played COD4, we had a dedicated server setup at the back of the server room. With MW2, we need to be able to connect to steam to be able to play multi-player. I've found this support article here: https://support.steampowered.com/kb%5Farticle.php?ref=8571-GLVN-8711 Which outlines all the ports I need to open. I went through and created the following rules in ISA 2000 (I'm stuck with 2000 for now). Protocol Definition: Steam Primary connection: Port 27000, UDP, Send Receive Secondary Connection: Port range 27001-27030 Send Receive Protocol Definition: Steam TCP In Primary connection: 27014, TCP, Inbound Secondary Connection: Port range: 27015-27050, Inbound Protocol Definition: Steam 4380 Primary connection: 4380, UDP, Send Receive When I start steam on my local workstation (I did add an exception to the Vista Firewall to allow steam), the steam client sits on "Updating Steam" for 5 minutes then errors out with: You must connect to the internet first. Any ideas? I assume I missed something. Thanks for your help.

  Read the article

• What is causing sudden freezing during running real-time program?

  - by Trevor Boyd Smith

  So I run a high intensive (CPU/GPU) real-time program. During normal execution suddenly everything freezes for 1-4 seconds. I opened "Process Explorer" in the background to help gain insight and maybe identify something. Here is what the CPU/GPU graphs looks like when I align them in time: Notice the 4 distinct drops in both the CPU/GPU. You can see that it goes from some sort of positive CPU/GPU usage to almost zero. These drops in the graph align with when the real-time program suddenly freezes. How do I find what is causing these sudden drops? NOTE: When you put your mouse over the graph it tells you the time, accurate to the second, for where your cursor is. Maybe this mouse over feature could be helpful in some way (e.g. what if you had a log of all processes every 100ms). EDIT: The real-time program is a video game and so I can't watch some sort of instrumentation while the video game is running. I need a solution that let's you look back in time somehow to see what was happening when the slow down occurred. EDIT: RE - Recording Data vs using real-time monitor: So the windows performance recorder is for some reason not recording what I expect it to record. So I switched to using "perfmon" and then opening it's "resource monitor". RE - Setting it up so I can view real-time monitor: In the video game I set it to spectate and then put the video game in "windowed" mode so that I can view the real time display that Resource Monitor has. Now that I can get semi-real time (only once per second... how do you get more than once per second?) I started looking at the various real time data readouts. Getting to the cause: I noticed a strong correlation in high disk IO and low CPU usage (which is also seen by having in-game freezing). How do you use resource monitor to find out who is doing all this offending disk IO?

  Read the article

• Best shortcut in Total Commander

  - by life-warrior

  So, what's your favourite TC shortcut or shortcut combination ? Which one do you use and for what purpose ? Among my most often used: Ctrl-Left ( or Ctrl-Right ) - open archive or folder under cursor in opposite tab. Ctrl-Shift-Enter, Alt-F8, Ctrl-X - copy full file path to clipboard. Shift-F6, Shift-End(if needed), Ctrl-C - copy only file name w/o path. Select files, Ctrl-M - multi-rename, for example remove "DVDrip" from file names. Ctrl-\ - go to root directory. Ctrl-D, - go to directory with highlighted letter specified. For example, name a downloads directory "&Downloads" in favourites, and the letter after ampersand will be highlighted. Alt-F7, feed to listbox, Ctrl-A, Mark(menu)-Save selection to file - creates a file with all files and directories inside current, with full path. Ctrl-[3-6] - sort files by name(3), extension(4), date(5), size(6). For example, Sort by name, when you need movies and soundracks with the same name and different extension to group them together. Sort by extension, when you need to find EXEs in Windows directory. Sort by Date, when you need to find the latest file downloaded in your dir. Sort by size, when you need to delete the largest files for free space.

  Read the article

• Debian/Ubuntu - No network connection

  - by leviathanus

  I have a very weird situation on my Ubuntu 12.04 LTS Server. I can not access (ping) my gateway, although I believe my config is ok - I attach the outputs. Any hints where to look? (I changed the beginning of the IP to something different, just obfuscation) ping 5.9.10.129 PING 5.9.10.129 (5.9.10.129) 56(84) bytes of data. From 5.9.10.129 (5.9.10.129) icmp_seq=2 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=3 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=4 Destination Host Unreachable uname -r 3.2.0-29-generic ifconfig eth0 eth0 Link encap:Ethernet HWaddr 3c:97:0e:0e:54:d7 inet addr:5.9.10.142 Bcast:5.9.10.159 Mask:255.255.255.224 inet6 addr: fe80::8e70:5aff:feda:c4ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1216 errors:0 dropped:0 overruns:0 frame:0 TX packets:490 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107470 (107.4 KB) TX bytes:34344 (34.3 KB) Interrupt:17 Memory:d2500000-d2520000 ip route default via 5.9.10.129 dev eth0 metric 100 5.9.10.128/27 via 5.9.10.129 dev eth0 5.9.10.128/27 dev eth0 proto kernel scope link src 5.9.10.142 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 5.9.10.129 0.0.0.0 UG 1000 0 0 eth0 5.9.10.128 5.9.10.129 255.255.255.224 UG 0 0 0 eth0 5.9.10.128 0.0.0.0 255.255.255.224 U 0 0 0 eth0 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination UPD: Eric, this is how routing information looks on a working server: 0.0.0.0 78.47.198.49 0.0.0.0 UG 100 0 0 eth0 78.47.198.48 78.47.198.49 255.255.255.240 UG 0 0 0 eth0 78.47.198.48 0.0.0.0 255.255.255.240 U 0 0 0 eth0 As I understand it, Hetzner tries to ensure security by this, so I can not take over an IP by changing my MAC. But this is another server, which has another netmask (255.255.255.240) UPD2: BatchyX, on the working server: 78.47.198.49 dev eth0 src 78.47.198.60 cache on the broken: 5.9.10.129 dev eth0 src 5.9.10.142 cache

  Read the article

• Weird mouse behaviour. Debian wheezy

  - by DevNoob

  When I move my mouse slowly over the desktop the pointer jumps often a few pixels (one or two) in the opposite direction of which I move my mouse. Horribly when trying to set the cursor around some semicolons in eclipse. I guess this is the result of a wrong set resolution of it. I suppose this is because the mouse was set initially really fast and even if I do xset 1/2 3, the mouse is just to fast and unprecise for me. It aready tried to configure the xorg.conf like this: Section "InputDevice" Identifier "Configured Mouse" Driver "mouse" Option "Device" "/dev/mouse" Option "Protocol" "Auto" Option "Name" "Logitech G3" Option "Resolution" "2000" EndSection But with no effect. Maybe because there is no /dev/mouse. This ist the content of dev. Maybe you can tell me which one is the mouse. autofs block bsg btrfs-control bus cdrom cdrw char console core cpu cpu_dma_latency disk dvd dvdrw fd fd0 full fuse fw0 hidraw0 hidraw1 hpet input kmsg log loop0 loop1 loop2 loop3 loop4 loop5 loop6 loop7 loop-control MAKEDEV mapper mcelog mem net network_latency network_throughput null nvidia0 nvidiactl oldmem port ppp printer psaux ptmx pts random rfkill root rtc rtc0 sda sda1 sda2 sda3 sda5 sda6 sda7 sda8 sdb sdb1 sg0 sg1 sg2 shm snapshot snd sndstat sr0 stderr stdin stdout tty tty0 tty1 tty10 tty11 tty12 tty13 tty14 tty15 tty16 tty17 tty18 tty19 tty2 tty20 tty21 tty22 tty23 tty24 tty25 tty26 tty27 tty28 tty29 tty3 tty30 tty31 tty32 tty33 tty34 tty35 tty36 tty37 tty38 tty39 tty4 tty40 tty41 tty42 tty43 tty44 tty45 tty46 tty47 tty48 tty49 tty5 tty50 tty51 tty52 tty53 tty54 tty55 tty56 tty57 tty58 tty59 tty6 tty60 tty61 tty62 tty63 tty7 tty8 tty9 ttyS0 ttyS1 ttyS2 ttyS3 uinput urandom usb vcs vcs1 vcs2 vcs3 vcs4 vcs5 vcs6 vcs7 vcsa vcsa1 vcsa2 vcsa3 vcsa4 vcsa5 vcsa6 vcsa7 vga_arbiter vmci vmmon vmnet0 vmnet1 vmnet8 vsock watchdog xconsole zero So my question is: How do I setup my mouse correctly in Debian wheezy?

  Read the article

• Server freezes while installing Redhat Enterprise Linux Server 6

  - by eisaacson

  We've tried both the first options Install or upgrade an existing system Install system with basic video driver When trying option #1, it gets to a screen that has a solid cursor about halfway down, then freezes. When trying option #2, it freezes at the point where it says: Waiting for hardware to initialize... Of course, we bought the unsupported version and haven't found anything to help us so far. Here are the specs to the server in the original post: ASUS P8Z68-M Pro LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard with UEFI BIOS RAIDMAX Reiter ATX-305WBP Black Steel / Plastic ATX Mid Tower Computer Case 450W Power Supply Intel Core i7-2600 Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 2000 BX80623I72600 16GB Ram OCZ Agility 3 SSD 120GB From some of the posts out there could the UEFI Bios or the Sandy Bridge processor be a culprit here? We just tried the DVD on a different computer and it got past that point with ease. It's a standard Dell build compared to our custom machine. Could it be having difficulty recognizing drivers? How do we get past that?

  Read the article

• Change the order of IP addresses returned by ifconfig?

  - by erikcw

  I have an Ubuntu server with several IP addresses attached to it. 127.0.0.1 is listed as venet0 by ifconfig. I'm using Chef to configure the server. The problem is that chef is listing 127.0.0.1 as the IP address for the server instead of one of the server's "real" IPs. (apparent "ohai ipaddress" uses the first IP listed by ifconfig to determine the server's IP). How can I change the order so the servers main IP is listed first instead of the 127.0.0.1? Can venet0 be deleted and venet0:0 be "promoted" to take its place since 127.0.0.1 is already listed in the "lo" interface? lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16700 (16.7 KB) TX bytes:16700 (16.7 KB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:7622207 errors:0 dropped:0 overruns:0 frame:0 TX packets:8183436 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2102750761 (2.1 GB) TX bytes:2795213667 (2.7 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX1 P-t-P:XXX.XXX.XXX.XX1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX2 P-t-P:XXX.XXX.XXX.XX2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 route -n route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 venet0 0.0.0.0 192.0.2.1 0.0.0.0 UG 0 0 0 venet0

  Read the article

• DXVA and ATI.... what am I missing?

  - by Shiki

  ATI Radeon HD3650 ffdshow (the one comes with CCCP 2010-10 AND the latest from Free-codecs site) Catalyst 10.12 Latest DirectX, Windows 7 HP x64 If I try to play it simply, the player (mpc-hc) won't use the acceleration. If I disable checks, I get artifacts. Back then it worked perfectly with my Intel and ATI too (Lenovo ThinkPad T500, switchable graphics). This only appeared recently. What should I do? What am I missing? If possible, I don't really want to downgrade drivers (waaa ATI drivers s.ck ... sorry but.. honestly), because the older one got a buggy DP driver so my external display gets a totally wrong resolution. Info about the media file: Video: Format : AVC Format/Info : Advanced Video Codec Format profile : [email protected] Codec ID : V_MPEG4/ISO/AVC Writing library : x264 core 88 r1462 7fcffde Encoding settings : cabac=1 / ref=8 / deblock=1:0:0 / analyse=0x3:0x133 / me=umh / subme=8 / psy=1 / psy_rd=0.80:0.20 / mixed_ref=1 / me_range=24 / chroma_me=1 / trellis=2 / 8x8dct=1 / cqm=0 / deadzone=21,11 / fast_pskip=1 / chroma_qp_offset=-3 / threads=3 / sliced_threads=0 / nr=0 / decimate=1 / mbaff=0 / constrained_intra=0 / bframes=8 / b_pyramid=2 / b_adapt=2 / b_bias=0 / direct=3 / wpredb=1 / wpredp=2 / keyint=250 / keyint_min=25 / scenecut=40 / intra_refresh=0 / rc_lookahead=40 / rc=crf / mbtree=1 / crf=16.0 / qcomp=0.60 / qpmin=10 / qpmax=51 / qpstep=4 / ip_ratio=1.40 / aq=1:1.00 The sample file I'm testing at the moment: [Coalgirls]_Kiddy_Girl-and_01_(1920x1080_Blu-Ray_FLAC)_[91428679].mkv (I tried many x264 files, no use.) Artifacts

  Read the article

• Application (was Firefox) crash on first load on Ubuntu Linux on older Dell Laptop

  - by Ira Baxter

  I've had a Dell Latitude laptop since about 2000 without managing to destroy it. A month ago the Windows 2000 system on it did something stupid to its file system and Windows was completely lost. No point in reinstalling Windows 2000, so I installed an Ubuntu Linux on the laptop. Everything seems normal (installed, rebooted, I can log in, run GnuChess, poke about). ... but ... when I attempt to launch Firefox from the top bar menu icon, I get a bunch of disk activity, the whirling cursor icon goes round a bit and then (WAS: everything stops: icon, mouse. Literally nothing happens for 5 minutes. Ubuntu is dead, as far as I can tell. EDIT : on further investigation, spinning icon, mouse operated by touchpad freeze. There's apparantly a little disk activity occuring about every 5 seconds. I wait 5-10 minutes, behavior doesn't change) A reboot, and I can repeat this reliably. So on the face of it, everything works but Firefox. That seems really strange. The only odd thing about this system when Firefox is booting is that while it has an Ethernet port (that worked fine under Windows), it isn't actually plugged into an Ethernet. As this is the first Firefox boot since the Ubuntu install, maybe Firefox mishandles Internet access? Why would that crash Ubuntu? (I need to go try the obvious experiment of plugging it in). EDIT: I tried to run the Disk manager tool, not that I cared what it was, just a menu-available application. It started up like Firefox, I get a little tag in the lower left saying Disk P*** something had started, and then the same behavior as Firefox. At this point, I don't think its the Ethernet. Is it possible that the Ubuntu disk driver can't handle the disk controller in this older laptop? The install seemed to go fine.

  Read the article

• Unable to ping gateway via bridge nic

  - by Ara

  I'm trying to install KVM on Ubuntu 12.04 server. We have multiple nic on this server of which we primarily use eth0. The server network runs fine(i'm able to ping gateway, ping dns server and ping servers on internet) with eth0 /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local I installed bridge-utils and configured br0 as below /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.168.22.194 netmask 255.255.255.0 network 192.168.22.0 broadcast 192.168.22.255 gateway 192.168.22.1 dns-nameservers 10.71.130.58 10.71.130.60 dns-search test.local bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off Post which i'm able to ping servers on the same ip range 192.168.22.2-254 except for 192.168.22.1 (which is the gateway) also i'm not able to ping any other servers. I'm not able to ping this machine from network. The output for route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.22.1 0.0.0.0 UG 100 0 0 br0 192.168.22.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 I've been struggling with this issue for past 5 days, would be of help if anyone can point me in the right direction to fix this issue. Thanks in advance

  Read the article

• Creating Routes using the second NIC in the box

  - by Aditya Sehgal

  OS: Linux I need some advice on how to set up the routing table. I have a box with two physical NIC cards eth0 & eth1 with two associated IPs IP1 & IP2 (both of the same subnet). I need to setup a route which will force all messages from IP1 towards IP3 (of the same subnet) to go via IP2. I have a raw socket capture program listening on IP2 (This is not for malicious use). I have set up the routing table as Destination Gateway Genmask Flags Metric Ref Use Iface IP3 IP2 255.255.255.255 UGH 0 0 0 eth1 If I try to specify eth0 while adding the above rule, I get an error "SIOCADDRT: Network is unreachable". I understand from the manpage of route that if the GW specified is a local interface, then that would be use as the outgoing interface. After setting up this rule, if i do a traceroute (-i eth0), the packet goes first to the default gateway and then to IP3. How do I force the packet originating from eth0 towards IP3 to first come to IP2. I cannot make changes to the routing table of the gateway. Please suggest.

  Read the article

• Trying to connect simple VB6 ADO to SQL Server 2008

  - by Henry

  We have a VB6 App that -for current purposes - is very basic ADO: Dim a New ADODB.Recorset, set some basic properties like Cursor Location and Lock Type, set a Connection String and a .Source like "Select * from CustomerMaster", and .OPEN - nothing fancy here! Yet, on a new SBS installation with SQL Server 2008 across 2 Servers (one for Apps, the other dedicated to SQL!), it dies/hangs/crashes if you try to run such a Query from anything but the SQL Sever box. Initially, we were using the SQLOLEDB.1 driver, which would crash/hang the entire SQL Server after about 4 such queries (built a simple 6 line App just for this purpose). Then switched to the NATIVE SQL driver, which did allow us unlimited, happy queries - until you did the first Change/Update - THEN it would corrupt the SQL Server if you exited and tried to go back in. All this 'corruption' is happening from the 'App Server' of the SBS pair, and I presume that the App Server (also installed in tandem with the SQL server this week) has the latest MDACs, etc. And running it from a 'lowly XP workstation' is (obviously) no better. ANY ideas??? -Henry

  Read the article

< Previous Page | 140 141 142 143 144 145 146 147 148 149 150 151  | Next Page >