Search Results

Search found 4881 results on 196 pages for 'mr lost'.

Page 145/196 | < Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >

• Why can't I physically access my machine after a remote session?

  - by Steve Crane

  I have a Dell Optiplex 960 desktop running Windows 7 64-bit at work. I typically leave it locked rather than logged off when I go home, so that I'm able to remote in from home and continue working if I wish. This is where the problem comes in. If I don't remote in there is no problem and I can simply unlock the next morning. It's when I do remote in that I have a problem. Remote sessions work as expected but when I get to work the next morning the machine appears to have gone into a sleep or hibernate state, from which no amount of mouse moving or keyboard pounding will wake it. The machine is not hanging as remote sessions to it are still possible; it seems that physical access from it's own mouse and keyboard are lost. The only way to gain access is to press and hold the power switch for several seconds until the machine shuts down. Of course this means Windows does not gracefully shut down and after powering up it takes several minutes for the machine to boot and reach the login prompt; presumably while it checks the disk. Has anyone else seen something like this?

  Read the article

• BIOS not detecting working SATA hard drive.

  - by Evan

  Some time ago my power supply died. It's a long story from then till now, but the important bit is that I ended up with a new hard drive and a new power supply. I tested to see if my original hard drive was still alive, and it booted and worked perfectly until I turned it off. When I started it again it would not boot. I bought new SATA cables, assuming that the one I had was not seating properly (it was cheap and wobbly), but no dice. Upon start-up I am presented with a message telling me to insert boot media into the selected drive or add a drive and restart. Neither the new or the old drive is detected by BIOS, my Vista install disk, or from my bootable Linux USB drive. When I remove all of the RAM the computer ceases outputting visual information, and upon reinstalling the ram and starting up again gives me a "failed overclock" error. So, does anyone have an idea as to what might be going on? I'm completely lost at this point.

  Read the article

• w2k3 AD DC Demotion fails with "no other AD DC for that domain can be contacted"

  - by Kstro21

  i've a small office with a single w2k3 sp2 DC(bad idea, but it is real), now, i want to make a clean install of that pc, so, i got another one, install w2k3 sp2, add it to the domain, dcpromo and set it to be a GC, untill now everything is ok, then tried to dcpromo in the primary DC, but it fails with The box indicating that this domain controller is the last controller for the domain mydomain.com is unchecked. However, no other Active Directory domain controllers for that domain can be contacted. Do you wish to proceed anyway? If you click Yes, any Active Directory changes that have been made on this domain controller will be lost. So, i started to move all the roles to the new server as described here, when all was ok with the roles, i tried doing the same, but got the same result. Tried moving the DNS to the new server, but it doesn't make difference. Shutdown to the old server, then tried to log into a workstation, but it fails saying the domain is not available, also coudln't add new workstation to the domain, so i have to power on the old server again. So, if i successfully move all the roles and dns to the new server: why dcpromo give such message in the old server? why if i shutdown the old server the domain is not available?? if i successfully move all the roles and dns to the new server, and i click yes when dcpromo give warning in the old server, will i lose all users, computers, ou, etc.? am i missing some steps to make this work?? hope you can help me thanks

  Read the article

• Postfix message ID originating process?

  - by Anders Braüner Nielsen

  Last night my postfix mail server(Debian Squeeze with dovecot, roundcube, opendkim and spamassassin enabled) started sending out spam from a single domain of mine like these: $cat mail.log|grep D6930B76EA9 Jul 31 23:50:09 myserver postfix/pickup[28675]: D6930B76EA9: uid=65534 from=<[email protected]> Jul 31 23:50:09 myserver postfix/cleanup[27889]: D6930B76EA9: message-id=<[email protected]> Jul 31 23:50:09 myserver postfix/qmgr[7018]: D6930B76EA9: from=<[email protected]>, size=957, nrcpt=1 (queue active) Jul 31 23:50:09 myserver postfix/error[7819]: D6930B76EA9: to=<[email protected]>, relay=none, delay=0.03, delays=0.02/0/0/0, dsn=4.4.2, status=deferred (delivery temporarily suspended: lost connection with mta5.am0.yahoodns.net[66.196.118.33] while sending RCPT TO) The domain in question did not have any accounts enabled but only a catchall alias set through postfixadmin - most emails were send from a specific address I use frequently but some were also sent from bogus addresses. None of the other virtual domains handled by postfix were affected. How can I find out what process was feeding postfix/sendmail or more info on where they originated? As far as I can tell php mail() wasn't used and I've run several open relay tests. I did a little tinkering(removed winbind from the server and ipv6 addresses from main.cf) after the attack and it seems to have subsided but I still have no idea how my server was suddenly sending out spam. Maybe I fixed it - maybe I didn't. Can anyone help figuring out how I was compromised? Anywhere else I should look? I've run Linux Malware Detect on recently changed files but nothing found.

  Read the article

• How to log kernel panics without KVM

  - by Spacedust

  My server is crashing and I can't find an answer why. It all started after my datacenter upgrade RAM from 16 GB to 32 GB. I also found such logs in dmesg - they've started to show itself just before the first kernel panic: EXT4-fs error (device md2): ext4_ext_find_extent: bad header/extent in inode #97911179: invalid magic - magic 5f69, entries 28769, max 26988(0), depth 24939(0) EXT4-fs error (device md2): ext4_ext_remove_space: bad header/extent in inode #97911179: invalid magic - magic 5f69, entries 28769, max 26988(0), depth 24939(0) EXT4-fs error (device md2): ext4_mb_generate_buddy: EXT4-fs: group 20974: 8589 blocks in bitmap, 54896 in gd JBD: Spotted dirty metadata buffer (dev = md2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. EXT4-fs error (device md2): ext4_ext_split: inode #97911179: (comm pdflush) eh_entries 28769 != eh_max 26988! EXT4-fs (md2): delayed block allocation failed for inode 97911179 at logical offset 1039 with max blocks 1 with error -5 This should not happen!! Data will be lost EXT4-fs error (device md2): ext4_mb_generate_buddy: EXT4-fs: group 21731: 5 blocks in bitmap, 60762 in gd JBD: Spotted dirty metadata buffer (dev = md2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. My system is CentOS 5.8 64-bit with latest kernel 2.6.18-308.20.1.el5. How can I check what is the reason of kernel panic without having an access to the KVM ? I have told my datacenter admins to check the memory in the server.

  Read the article

• Access denied to external USB disk; update access rights fails in Windows 8

  - by gerard

  I use to work with 2 laptops (Windows vista and Windows 7), my work files being on an external usb disk. My oldest laptop broke down, so I bought a new one. I had no option other than take Windows 8. I suspect something changed with access rights, as my external disk suffered some "access denied" problem on Windows. I was prompted (by Windows 8) somehow to fix the access rights, which I tried to do, getting to the properties - security. This process was very slow and ended up saying disk is not ready Additionally, my external usb disk somehow was not recognized anymore. Back to Windows 7, I was warned that my disk needed to be verified, which I did. In this process, some files were lost (most of them I could recover from the folder found00x, but I have some backup anyway). Also, I don't know why, but under Windows 7, all the folder showed with a lock. Then back again to Windows 8. Same problem : access denied to my disk + no way to change access rights as it gets stuck disk is not ready". Now I am pretty sure there is some kind of bug or inconsistency in Windows 8 / Windows 7. I did 2. and 3. a few times. At some point, I also got an access denied in Windows 7. I could restore access rights to the disk to "System" (properties - security - EDIT for full control to group "system". ). But then I still get the same access right pb on Windows 8, and getting stuck in the process to restore full control to "system" -- and "admin" groups. I upgraded Windows8 with the Windows8 updates available. Does not help.

  Read the article

• Setting up squid proxy server to in turn connect using another proxy server [closed]

  - by AnkurVj

  My institute uses the Squid proxy server and authentication mechanism requires username and password to be entered. This means that, I can log in on only one machine at a time and Internet access for me is restricted to that machine. I sometimes require Internet access on multiple machines simultaneously. What previosuly worked for me was the following : On one of my own machines A, I set up a Squid proxy server that allowed all local machines without any username and password. I configured rest of the machines to use this machine A as the proxy server. On machine A I logged into the institute proxy server using my browser. This way, I could access Internet from all my machines, by effectively channeling my requests through the server A. Recently, I lost that machine and configuration and now I tried to set it up again in the same manner. However, I cant seem to remember exactly how I made it work. I keep getting Connection Refused (111) on other machines. My guess is that my squid server isnt able to forward requests from other machines to the actual squid server. I could use any help for debugging this problem. I don't want to use alternatives such as ssh tunneling. This solution has worked for me in the past, I just don't remember how to set it up the same way again.

  Read the article

• MS Dynamics CRM users disappear

  - by Max Kosyakov

  Recently we came across quite a weird issue. The administrators say that once in a while they notice that user accounts in MS Dynamics CRM are lost . When a new user is added to the system, the administrators add him/her to the Active Directory first. Then, they go to Dynamics CRM interface, then to system configuration -> administration -> users and add the new user to the CRM, add roles to this user, grant them relevant permissions. Then the user is able to use a custom application, which connects to the Dynamics CRM via WCF. After a while (few weeks or months) the user is unable to use the custom application because Dynamics CRM cannot authorise this user. When administrators open the Dynamics CRM user management interface (configuration -> administration -> users ) and browse through the list of CRM users they cannot find the user in the list. When they try to add the user to Dynamics CRM back, the CRM fails with the error message "User already exists". Moreover, the user still exists in the Active Directory. The admins are very sure the user had been added to the CRM before he/she started to work. The only fact the the user was able to use the custom application normally says that the user had been indeed registered in the CRM. How come the user is not listed in the CRM user management interface at all? Have anyone faced any issues like that? Seen or heard of disappearing CRM users somewhere? Any help is appreciated. Where can one start digging?

  Read the article

• xauth, ssh and missing home directory

  - by flolo

  We have several servers, and normaly everything works fine, except now... we get a new aircondition installed. This takes 36 hours and for this time almost all servers got shutdown, only 2 remaining servers run for the most important tasks (i.e. accepting incoming email, delivering some important websites, login-server). Everybody was informed that when they need appropiate data from the homedirs they should fetch it before take down. Long story short: Someone realized that he have run a certain program on one of the servers. No Problem, he can remote login into our login server and run the programm there without home directory (binaries are local and necessary information can be copied to the /tmp). That works like a charm until... ... the user needs to run a GUI programm. I find no easy way to make it running, usually ssh -Y honk@loginserver is enough but now the homedirectory is missing and ssh is not able to copy the cookies into ~/.Xauthority (as the file server with the home directories is down). Paranoid as all systemadmins all X-Server just listen locally not on tcp ports, so no remote X connection possible SSH config is waterproof - i.e. no way to set environment variables. My Problem is, that the generated proxy MIT cookie from ssh get lost as the .Xauthority doesnt exist. If I could retrieve it somehow I could reenter it a .Xauthority in /tmp. The only other option (besides changing the config) which came to my mind is, makeing a tunnel (netcat, or better ssh) from the remote host to the loginserver and copy the cookie manually (not sure if it the tcp-unix domain socket stuff works as expected). Any good suggestions (for the future - now our servers are already up)?

  Read the article

• MySQL ADO.NET Connector & MSSQL Integration Services

  - by user1114330

  Here I am, day three... attempting to sync a data view on a Windows Vista box (64 bit) running MSSQL 2012 and Visual Studio 2010. Sanity is slipping and hunger for progress fills my attention. I went through hell trying to get the MySQL ODBC drivers to get the job but to no avail...everyone seems to be lost and all the threads I can find are solutions that do not work for me. The problem: System DSN's not being seen by SSIS. SSIS DSN Not Showing as ODBC Data Source I make the decision to try out the ADO.NET connector...and to my surprise it is actually in the selection list in data sources in SSIS. So I take off running to create a Data Flow Task, create an ADO.NET Source (a local MSSQL DB)...all is good as usual. Then I move swiftly to creating a ADO.NET Destination, enter my credentials...wow, I am selecting a database finally on my linux server! Happy thinking that I finally have figured a way to get the job done. Then I move to mappings...nope, something is wrong...I am getting an error that hurts my eyes: Pipeline component has returned HRESULT error code 0xC0208457 from a a method call. Error at Data Flow Task [ADO NET Destination [81]]: Failed to get properties of external columns. The table name you entered may not exist or you do not have SELECT permission on the table object and an alternative attempt to get column properties through connection has failed. Detailed error messages are" You have an error in your SQL syntax check the manual that corresponds to your MySQL server version for the right syntax to use near "database".tablename" at line 1. The descriptor files on path C:\Program Files (x86)\Microsoft SQL Server\110\DTS\ProviderDescriptors\ does not contain schema information for connection of type MySQL.Data.MySqlClient.MySqlConnection. So it looks like it can't the information and therefore I cannot map the tables properly. Any ideas on this would be ultra helpful...thanks in advance to All!

  Read the article

• Outlook locking network connection/session?

  - by HaydnWVN

  Scenario: We have an 'automatic orders' machine sat in the corner running XP with Outlook 2003. Its job is to check for new emails on a specific account, when it encounters one it checks the e-mail body for specific wording to determine which customer it is from (using a macro), then it checks the attachment for specific order codes before parsing the attachment to create a .csv file (which is then e-mailed onto one of the sales team) before importing the .csv into our bespoke ERP/Sales Order system to create an order. Problem: Periodically the machine will have symptoms of a lost network connection (unable to connect to any network source). Sometimes after several days, sometimes over a week. Volume of emails/orders processed does not seem to be linked. Additional info: The machines .pst is stored on a mapped network location. The .csv created is stored on a mapped network location. This is a workgroup, not a domain. All network drives are Samba shares from an Ubuntu fileserver. Our bespoke system runs from a database (MySQL) Ubuntu server. Our troubleshooting so far: I have switched machines (previous was Win2000) with the same symptoms. Restarting the machine FIXES the problem. Closing Outlook and then end tasking an Outlook.exe background process FIXES the problem. If you close Outlook, without end taking the background process, outlook will not reopen (saying it cannot find the pst file & it will not open any network location). Does Outlook have some kind of 'max session' linking it to network activity that is not closing after a mail request? Could Auto-archive be causing this? Is there a tool to check/display what each outlook.exe process is doing? Have not found many ways to troubleshoot this yet, as it is so infrequent...

  Read the article

• Getting 0xc00000e windows 7 "Boot device inaccessible" after random crashes

  - by Dynde

  I've been having some weird random crashes that I can't seem to locate, and I'm unsure if it's windows or hardware related. It's a brand new computer and very powerful. I've run into a couple of these random crashes, now I don't know what causes them, as it happens during the night, when I'm sleeping. When I wake up, all I see is a boot manager screen that says Exception: 0xc00000e "Boot device inaccessible". A simple restart doesn't fix the problem - it seems to struggle locating my primary hdd - but a complete shutdown works, it'll just fly straight into windows again. The event viewer doesn't tell me much. The most reason incident just gives me this: "The previous system shutdown at 08:55:44 on ?11-?12-?2011 was unexpected." And also a kernel power event: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. and I can see only two application event entries around that time at 8.47 (about 8 minutes prior to the crash): The Windows Modules Installer service entered the running state. The WinHTTP Web Proxy Auto-Discovery Service service entered the running state. Can anyone tell me anything about this, or direct me to a forum or something that might know what's wrong? I can supply the extra details of the events too if needed. The hdd is an SSD - could that have anything to do with it? I ran a few diagnostics and memory and hdd should be okay - at least the diagnostics report is clean. Is it a faulty drive?

  Read the article

• I deployed Flash Player via a Software Installation policy. How to upgrade?

  - by eleven81

  I have a Windows Server 2008 machine as my DC. Earlier this year I created a Software Installation GPO to deploy Adobe Flash Player plugin MSI. I assigned the policy to the computers, about half run Windows XP x86 and the other half Windows 7 x64. That all works like clockwork. When I created the Software Installation Policy, I disabled the Flash Player plugin's automatic update feature by editing the MSI in Orca. I did this because I wanted all of my machines to run the exact same version of the plugin. Now, some time has passed and a newer version of the Flash Player plugin has been released. It is time for me to push out the updated version of the plugin. I already have the new MSI, but I am lost on what to do next. I see the upgrades tab in the Software Installation GPO, but everything there reads like that would be used for add-ons to a larger master program and not for updates that are released over time. I have read that it is best to create a new Software Installation policy with the new MSI, revoke the old GPO, and assign the new GPO. I feel as though, over time, I will wind up with more revoked policies than active ones. I have also read that some people have had success by replacing the old MSI with the new MSI and simply telling the GPO to redeploy. This seems like a backdoor method that will only get me in to trouble. In short, what is the correct, best-practice, or preferred way to roll out the new version via Group Policy?

  Read the article

• IP6 seems to be enabled - How do I configure it without interfering with IP4?

  - by Mister IT Guru

  I noticed that some of my Centos boxes have IP6 enabled, and seem to have addresses. I have no problem with this, but I would like to get a handle on it, and even connect to them using IP6. This would really help if for any reason DHCP has a hiccup. But I'm a bit lost as to where the configuration on my CentOS box is. (I am also on google researching this, but I like server fault! :) ) I am hoping that I would be able to log into this via the VPN because every now and then that DHCP device has a bad morning, and needs to be restarted. (I'm also looking into this issue, but someone else handles that, management separation gone mad!) It's a remote client, so it would be a lot easier for me to connect to these systems which seem to self configure, to use that as a pivot via ssh tunnels to get to other remote devices to continue to manage them, while out main route is fixed. I guess, my questions are How can I configure IP6 without interfering with IP4, and On CentOS, can I influence this auto configuration I seem to be seeing?

  Read the article

• Deploying a Django application in a virtual Ubuntu Server

  - by mfsaint

  I have a virtualbox machine running Ubuntu Server 10.04LTS. My intention is to this machine to work like a VPS, this way I can learn and prepare for when I get a VPS service. Apache+mod_wsgi for deploying the Django app seems the right choice to me. I have the domain (marianofalcon.com.ar) but nothing else, no DNS. The problem is that I'm pretty lost with all the deployment stuff. I know how to configure mod_wsgi(with the django.wsgi file) and apache(creating a VirtualHost). Something is missing and I don't know what it is. I think that I lack networking skills ant that's the big problem. Trying to host the app on a virtualbox adds some difficulty because I don't know well what IP to use. This is what I've got: file placed at: /etc/apache2/sites-available: NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] ServerName www.my-domain.com ServerAlias my-domain.com Alias /media /path/to/my/project/media DocumentRoot /path/to/my/project WSGIScriptAlias / /path/to/your/project/apache/django.wsgi ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined </VirtualHost> django.wsgi file: import os, sys wsgi_dir = os.path.abspath(os.path.dirname(__file__)) project_dir = os.path.dirname(wsgi_dir) sys.path.append(project_dir) project_settings = os.path.join(project_dir,'settings') os.environ['DJANGO_SETTINGS_MODULE'] = 'myproject.settings' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler()

  Read the article

• Ubuntu 10.04->10.10 in failed state - how to recover?

  - by Harvey

  I was running Ubuntu 10.04 and attempted to upgrade to 10.10. I have a really slow connection (DSL 128kbits/sec) and copying the upgrade files took about 26 hours. I of course let it run unattended. When I came back, I notice the following 3 dlgs: (1) "Could not install the upgrades The upgrade has aborted. Your system could be in an unusable state. A recovery will run now (dpkg -- configure -a)." (2) "gpk-update-icon Distribution upgrades available maverick 10.10 (stable) [more information] [Do no show this again] [Cancel] [Ok]" (3) "gpk-update-icon Security updates available The following important updates are available for your computer: libwebkit-1.0-2-dbg - Web content engine library for Gtk+ - Debugging symbols libcupsimage2 - Common UNIX Printing System(tm) - Raster image library ..." What is the best response to all of this? I went through something similar in an attempted network upgrade from 8.04 to 10.04 and had to reload the unbootable machine fresh from distribution media (all data was lost). I'd like to avoid that here. I have not yet responded to the dialogs, and want to make sure the system is still bootable and not lose my data this time.

  Read the article

• Can start-stop-daemon use environmental variables?

  - by scottburton11

  I need to daemonize a Windows app running in Wine, and create a pid in /var/run. Since it requires an X11 session to run, I need to make sure the $DISPLAY variable is set in the running user's environment. Assuming I already have a X11 session running, with a given display, here's what the start-stop-daemon line looks like in my /etc/init.d script: start-stop-daemon --start --pidfile /var/run/wine-app.pid -m -c myuser -g mygroup -k 002 --exec /home/myuser/.wine/drive_c/Program\ Files/wine-app.exe Unfortunately, my version of start-stop-daemon on Ubuntu 8.04 doesn't have the -e option to set environmental variables. I gather that you could simply set $DISPLAY before the command, like so: VAR1="Value" start-stop-daemon ... But it doesn't work. Since I'm using the -c {user} option to run as a specific user, I'm guessing there's an environment switch and VAR1 is lost. I've tried exporting DISPLAY from the running user's .profile and/or .bashrc but it doesn't work either. Is there another way to do this? Is this even possible? Am I overlooking something? Many thanks

  Read the article

• Custom keyboard map is causing issues with stuck keys

  - by Grumbel

  I have a Microsoft Ergonomic 4000 keyboard and I am running a custom keymap (dvorak with some stuff for umlauts): http://pingus.seul.org/~grumbel/tmp/md5/b054e11505c88e1bfc6ebd5da46bdb78-xmodmap_pke http://pingus.seul.org/~grumbel/tmp/md5/f5e42a5b8ba4a034c5945f719b3d2608-xmodmap_pm This used to work fine for years and it still does, except that I am now having issues with a stuck Mode_switch key. When I hit Control_R and Mode_switch at the same time (happens a lot by accident), the Mode_switch key gets into a 'stuck' state, all letters I type afterwards come out in their umlaut form as if Mode_switch is pressed. I can unstuck the Mode_switch by again hitting Control_R and Mode_switch at the same time, but that leaves Gnome in a broken state where it doesn't react to my Gnome keyboard shortcuts any longer. The key presses themselves are still registered by the window manager as one can see changes in the applications (cursor in Gnome Terminal will turn into an unfilled rect, as if the application lost focus), but don't trigger the bound action. Does anybody have a clue what could be causing this? Or does anybody has an idea how I could debug this? xev doesn't seem to help here, as it is reporting normal KeyPress/KeyRelease events, even when the key is stuck. Also the Gnome key bindings don't get reported at all when its in the 'broken' state. I assume they are captured by the window manager before they even reach xev. I am using Ubuntu 10.04 with Gnome and Metacity, I have disabled all OpenGL related effects, so Compiz shouldn't interfere. Some general info on which applications are involved in Gnomes key binding handling would be helpful as well, as I assume its metacity, but restarting metacity doesn't fix the issue.

  Read the article

• Two servers, two domains, one ip. mod_proxy beginner

  - by Gutsav

  I run two virtual web servers (both running apache2 on debian). I have just one external IP, but two domains, and I want a domain going to each of the servers. I've understood that I need a Reverse Proxy, and I enabled both the mod_proxy and the mod_proxy_http modules on the "primary server". Do I need to enable anything on the "secondary server"? I also understood that I need to write some things in a virtual host file, but what? On the primary server, I have a virtual host file for one of the domains, and some for subdomains. I want domain1.tld to go to the primary server (port 80 is forwarded to it, so that works) and domain2.tld to go to the other server (internal ip 192.168.0.x). No ports needs to be forwarded to it, right? So, what to add and in which virtual host file? Or a new one? Other questions suggest adding ProxyPass and ProxyPassReverse, but I'm lost anyway, and I just don't understand the apache documentation. Thanks in advance

  Read the article

• The Wifi is working fine but no internet connection in Windows 8 [migrated]

  - by Ali

  I'm currently having a Problem with my msi GT70 laptop. my laptop is running windows 8 and yesterday it requested a Restart to Update. after the Restart and the update I tried to surf the net through google chrome, the WiFi connection is perfect but the page I tried to access is not loading at all, after a while it shows failure to load page. I disabled and reenabled the WiFi chip through the device manager but still no internet connection. I uninstalled and reinstalled the drivers, still no internet. I updated the Driver of the wifi, still no internet, I even went to Wifi configuration and tried to change the DNS and reset it back to automatically, still no Luck.. I'm really lost I don't know what to do, I don't want to go deep and play with Laptop DNA "aka: registry file" and screw things up. I really appreciate any help in this matter. thanks in advance. Note: I tried to access many pages but no luck. I even tried Firefox, Opera, even ie still no luck. The internet is working fine on my tablet and cellphone, except for the Laptop.

  Read the article

• Intermittent FTP login issues (Microsoft IIS FTP Service)

  - by JaggenSWE

  I've got a somewhat weird problem which I'm not sure how to troubleshoot. We have a FTP running on a Windows Server 2003 machine using the IIS FTP Service, this is for our clients and is configured with IP-restrictions. However, now ONE of the clients starts complaining that they can't log in to the server from time to time. This is just ONE of 10+ clients that have this issue, which makes me think it's a problem on their side. Just to be on the safe side I had a peek into the FTP logs and found something strange. Whenever succeed in loggin in this is what I can find in the logs: nnn.nnn.nnn.70, userxxx, 2012-06-11, 09:22:32, MSFTPSVC1, SERVERNAME, nnn.nn.nn.11, 0, 0, 0, 331, 0, [191747]USER, userxxx, -, nnn.nnn.nnn.70, userxxx, 2012-06-11, 09:22:32, MSFTPSVC1, SERVERNAME, nnn.nn.nn.11, 0, 0, 0, 230, 0, [191747]PASS, -, -, However, if the login fails I see the following events: nnn.nnn.nnn.70, userxxx, 2012-06-11, 09:16:33, MSFTPSVC1, SERVERNAME, nnn.nn.nn.11, 0, 0, 0, 331, 0, [191739]USER, userxxx, -, nnn.nnn.nnn.70, -, 2012-06-11, 09:16:33, MSFTPSVC1, SERVERNAME, nnn.nn.nn.11, 0, 0, 0, 530, 1326, [191739]PASS, -, -, When you look at the event where the clients sends the PASS in the successful login it seems to know that it is infact "userxxx" that is coupled to that PASS, but when it fails it seems to be lost since user in the PASS event is set to "-". Anyone have any ideas around this, any help would be appreciated. :) //JaggenSWE

  Read the article

• Ways to recover data from external hard drive

  - by Howard Benson

  I use an external hard disk for backup of my mac with time machine (OS 10.5.8). I have made something wrong and I have found important folders in the recycler bin. These folders come from external hd. They are backup folders (backups.backupdb) and others. I have tried to restore them draggin and dropping. Some of them came back in the external hd in a while. For the others it takes hours to "preparing to copy" and then it has said "there's no space to copy" on ext hd. It's strange. Files are now in the recycle bin (180gb), and the ext had should have lot of free space. But it isn't really so. Ext hd is not free of space even if these files are in the bin. I ask for advices. I'm not also able to use time machine now (and i have "lost" old backups) for the same reason. Ext hd says that it has not free space.. Thanks

  Read the article

• Inkscape: Copying an object, retaining transparency

  - by dpk

  I'm looking for a way to copy objects from one window to another without losing the surrounding transparency. I have two Inkscape windows. The setup is pretty simple. In the first window I draw a filled circle and a filled rectangle in it, with the circle set on top of the rectangle to show that the area around the circle is transparent (that is, you can see the rectangle "under" the circle, see screenshot 1, left). In the second window I just drew a filled rectangle (screenshot 1, right). When I copy the circle from window 1 to window 2 the transparency around the circle is lost (screenshot 2). I've verified that the backgrounds of the documents are 0% alpha/white. This is a rather contrived example but is readily reproducible. The real graphics I am working with have a bunch of objects all in a single group, but I have the same results. I feel like I'm missing something. The circle no longer behaves like a circle at its destination. Instead, it acts kind of like a bitmap. I'm definitely not using the bitmap copy feature.

  Read the article

• Unable to sync iPod Touch with my PC

  - by alex

  I'm trying to sync a first gen iPod Touch to my PC running Windows 7 64 bit. The problem is that whenever I connect the iPod, iTunes completely freezes (if I start iTunes after connecting the iPod it will simply hang until it's physically disconnected from the PC). I reinstalled iTunes thinking that it had been corrupted, but without any luck. I've had this problem with all the latest versions of iTunes. I've also tried using MediaMonkey and DoubleTwist. None of these apps see the iPod as being connected; DoubleTwist also freezes, just like iTunes. The really strange thing is that I was able to sync the iPod with this PC a while back, but I now seem to have lost that ability. I don't know what changed. Windows detects the device every time it's plugged in (I can see it in Device Manager and I can browse all photos on iPod as if it were a camera). Also, I can sync it to iTunes on Mac OS X without any major problems.

  Read the article

• Using Samba to share a folder from a Linux guest with a Windows host in VirtualBox

  - by AmV

  I would like to share a folder from a Linux Guest with a Windows host (with read and write access if possible) in VirtualBox. I read in these two links: here and here that it's possible to do this using Samba, but I am a little bit lost and I need more information on how to proceed. So far, I managed to set up two network adapters (one NAT and one host-only) and install Samba on the Linux guest, but now I have the following questions: What do I need to type in samba.conf to share a folder from the Linux guest? (the tutorial provided in one of the links above only explains how to share home directories) Are there any Samba commands that need to be executed on the guest to enable sharing? How do I make sure that these folders are only available to the host OS and not on the Internet? Once the Linux guest is setup, how do I access each of the individual shared folders from the Windows host? I read that I need to mount a drive on Windows to do this, but do I use Samba logins, or Linux logins, also do I use localhost? or do I need to set up an IP for this? Thanks!

  Read the article

< Previous Page | 141 142 143 144 145 146 147 148 149 150 151 152  | Next Page >