Search Results

Search found 27649 results on 1106 pages for 'ask how to geek'.

Page 146/1106 | < Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >

  • Read only file system

    - by Jack Moon
    I'm running Ubuntu 12.10, Upon opening any shell I get the following error: /home/jack/.rbenv/libexec/rbenv-init: line 87: cannot create temp file for here-document: Read-only file system I realised this wasn't simply a rbenv issue, as any file I try to write to returns an error saying the system is Read-only. I don't know how else to describe my problem, each time I boot up the system goes through a disk check, where it supposedly fixes several errors in my disk. Here is my /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda1 during installation UUID=1cc4b2ab-a984-4516-ac25-6d64f5050244 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=4e0dfeae-701a-43ce-b5c6-65f15ab3d8e3 none swap sw 0 0 The entire file system is read-only. I've tried the following sudo fsck.ext4 -f /dev/sda1 which gave the following (shortened) output /dev/sda1: ***** FILE SYSTEM WAS MODIFIED ***** /dev/sda1: ***** REBOOT LINUX ***** /dev/sda1: 1257080/45268992 files (1.0% non-contiguous), 50696803/181051904 blocks

    Read the article

  • teamviewer in "client only" mode

    - by Tommy
    I have a remote PC with the teamviewer on it. I want to use my local teamviewer installation only for connecting to that remote PC, and I don't want any services (teamviewerd) running on my local Ubuntu 14.04. I've tried to disable the service by doing sudo teamviewer --daemon disable but after that I'm not able to connect to the remote PC, because teamviewer reports an error "The Teamviewer daemon is not running!" on start, and I'm not able to access the gui. Is there a way to connect to the remote PC with teamviewer with no teamviewerd running?

    Read the article

  • black screen after waking up from suspend

    - by Daniel De Leon
    running 11.10 and on wake up after being suspended (for a long time or 2 seconds, doesn't matter) I am presented with a black screen that just has a purple bar (about the size of the top menu bar). As far as I can tell the system is unresponsive to anything outside of a manual restart by pressing the power button on the tower, after which it starts normally. using the most up to date graphics driver, also tried switching to a different version, nothing. just switched back to Linux and this is really giving me a headache, I would really like this to work. Any help would be greatly appreciated.

    Read the article

  • mysql completely removing

    - by Dmitry Teplyakov
    I broke my mysql and now I want to completely reinstall it. I tried: $ sudo apt-get install --reinstall mysql-server $ sudo apt-get remove --purge mysql-client mysql-server But always I see popup with proposal to change root password, I change it and got an error that I can change it.. $ sudo apt-get remove --purge mysql-client mysql-server Reading package lists... Done Building dependency tree Reading state information... Done Package mysql-client is not installed, so not removed Package mysql-server is not installed, so not removed The following packages were automatically installed and are no longer required: libmygpo-qt1 libqtscript4-network libqtscript4-gui libtag-extras1 libqtscript4-sql libqtscript4-xml amarok-utils amarok-common libqtscript4-uitools liblastfm0 libloudmouth1-0 libqtscript4-core Use 'apt-get autoremove' to remove them. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up mysql-server-5.5 (5.5.28-0ubuntu0.12.04.2) ... 121114 19:04:03 [Note] Plugin 'FEDERATED' is disabled. 121114 19:04:03 InnoDB: The InnoDB memory heap is disabled 121114 19:04:03 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121114 19:04:03 InnoDB: Compressed tables use zlib 1.2.3.4 121114 19:04:03 InnoDB: Initializing buffer pool, size = 128.0M 121114 19:04:03 InnoDB: Completed initialization of buffer pool InnoDB: Error: auto-extending data file ./ibdata1 is of a different size InnoDB: 0 pages (rounded down to MB) than specified in the .cnf file: InnoDB: initial 640 pages, max 0 (relevant if non-zero) pages! 121114 19:04:03 InnoDB: Could not open or create data files. 121114 19:04:03 InnoDB: If you tried to add new data files, and it failed here, 121114 19:04:03 InnoDB: you should now edit innodb_data_file_path in my.cnf back 121114 19:04:03 InnoDB: to what it was, and remove the new ibdata files InnoDB created 121114 19:04:03 InnoDB: in this failed attempt. InnoDB only wrote those files full of 121114 19:04:03 InnoDB: zeros, but did not yet use them in any way. But be careful: do not 121114 19:04:03 InnoDB: remove old data files which contain your precious data! 121114 19:04:03 [ERROR] Plugin 'InnoDB' init function returned error. 121114 19:04:03 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 121114 19:04:03 [ERROR] Unknown/unsupported storage engine: InnoDB 121114 19:04:03 [ERROR] Aborting 121114 19:04:03 [Note] /usr/sbin/mysqld: Shutdown complete start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: mysql-server-5.5 E: Sub-process /usr/bin/dpkg returned an error code (1) It is good for me that I have not any important databases, but..

    Read the article

  • Bash prompt doesn't print until I interact with console again

    - by durron597
    I don't even know where to begin to diagnose this one. Usually, when a command finishes, the prompt prints itself for the next command. However, that is not happening. Hard to explain with words, I'll just use an example: User@Machine:~$ cp /mnt/mountname/directory/textfile.txt . After waiting several seconds (far too long for this operation on a small file) I press Enter, and see: User@Machine:~$ cp /mnt/mountname/directory/textfile.txt . User@Machine:~$ User@Machine:~$ So clearly the operation had finished, but the prompt didn't display... until I pressed enter, and then BOTH prompts instantly displayed. This error does not happen with commands like cd.

    Read the article

  • Installation problem Ubuntu 12.04 Crashing hardware error

    - by user93640
    I am running on Ubuntu 8.04 for quite some time without many problems. About almost a year ago or so I have been trying to upgrade to 10.04 LTS, but without any success. Each time when trying to upgrade or even newly install the installation process crashed after about an hour or so (I forgot exactly how long). Now I wanted to try Ubuntu 12.04 (not even installing, but I only selected "Try Ubuntu without installing") and I got similar errors. I did not try to install it, because of earlier experience with 10.04 when after I also lost 8.04 and had to install from scratch again (after which it worked). I get the following screen (as I am not allowed to upload photos here the text): 26.767262] [Hardware Error]: CPU 0: Machine Check Exception: 0 Bank 5: b200001804000e0f 26.767279] [Hardware Error]: TSC 0 26.767287] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017924 SOCKET 0 APIC 0 microcode 44 26.767297] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767307] [Hardware Error]: CPU 1: Machine Check Exception: 0 Bank 1: b200000000000175 26.767316] [Hardware Error]: TSC 0 26.767323] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017924 SOCKET 0 APIC 1 microcode 44 26.767331] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767339] [Hardware Error]: CPU 1: Machine Check Exception: 0 Bank 5: b200003000000e0f 26.767348] [Hardware Error]: TSC 0 26.767354] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017924 SOCKET 0 APIC 1 microcode 44 26.767363] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767371] [Hardware Error]: CPU 1: Machine Check Exception: 4 Bank 1: b200000000000175 26.767379] [Hardware Error]: TSC 1bf231e65f 26.767386] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017951 SOCKET 0 APIC 1 microcode 44 26.767395] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767403] [Hardware Error]: CPU 1: Machine Check Exception: 4 Bank 5: b200003008000e0f 26.767413] [Hardware Error]: TSC 1bf231e65f 26.767421] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017951 SOCKET 0 APIC 1 microcode 44 26.767429] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767437] [Hardware Error]: CPU 0: Machine Check Exception: 5 Bank 5: b200001806000e0f 26.767447] [Hardware Error]: RIP |INEXACT| 60:<00000000c1018b5c> {mwait_idle+0x7c/0x1d0} 26.767464] [Hardware Error]: TSC 1bf231e674 26.767471] [Hardware Error]: PROCESSOR 0:6f6 TIME 1349017951 SOCKET 0 APIC 0 microcode 44 26.767480] [Hardware Error]: Run the above through 'mcelog --ascii' 26.767487] [Hardware Error]: Machine check: Processor context corrupt 26.767495] Kernel panic - not syncing: Fatal Machine check 26.767505] Pid: 579, comm: debconf-communi Tainted: G M 3.2.0.29-generic-pae #46-Ubuntu 26.767515] Call Trace: 26.767525] [<c158f812>] ? printk+0x2d/0x2f 26.767534] [<c158f6e0>] panic+0x5c/0x161 26.767542] [<c10247ef>] mce_panic.part.14+0x13f/0x170 26.767551] [<c1024872>] mce_panic+0x52/0x90 26.767558] [<c1024a18>] mce_reign+0x168/0x170 26.767565] [<c1024bb5>] mce_end+0x105/0x110 26.767572] [<c10252db>] do_machine_check+0x32b/0x4f0 26.767581] [<c1024fb0>] ? mce_log+0x120/0x120 26.767590] [<c15a5e47>] error_code+0x67/0x6c 26.767602] panic occurred, switching back to text console 26.768498] Rebooting in 30 seconds.. For information, I have also tried earlier Arch Linux. I can install it, but when I try to install a window manager (LXDE) again I got similar errors. Fedora also crashes when installing and also Mandriva did not work for me. Therefore I think something deep in the machine might be wrong. But as stated above I can (clean) install 8.04 and also 9.10 can be installed without problems. Also updates for 8.04 can be installed. My machine is dual boot with XP next to it on a different partition. My HW: Memory : 2.0 GiB; Processor 0: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz; Processor 1: Intel(R) Core(TM)2 CPU 6320 @ 1.86GHz; How can I install Ubuntu 12.04? Last option would be to completely format my machine and install everything from scratch, but even I am not sure if that would solve it in the end. Can anybody help me out?

    Read the article

  • Gvim GLib-GObject-WARNING in ubuntu 13.10

    - by naveen.panwar
    I upgraded from ubuntu 13.04 to ubuntu 13.10 this afternoon. And when I try starting vim form the terminal after the upgrade, I get these warnings (gvim:4054): GLib-GObject-WARNING **: Attempt to add property GnomeProgram::sm-connect after class was initialised (gvim:4054): GLib-GObject-WARNING **: Attempt to add property GnomeProgram::show-crash-dialog after class was initialised (gvim:4054): GLib-GObject-WARNING **: Attempt to add property GnomeProgram::display after class was initialised (gvim:4054): GLib-GObject-WARNING **: Attempt to add property GnomeProgram::default-icon after class was initialised` How can I fix these and what exectly are these warnings about

    Read the article

  • Awk command to print all the lines except the last three lines

    - by Avinash Raj
    I want to print all the lines except the last three lines from the input through awk only. Please note that my file contains n number of lines. For example, file.txt contains, foo bar foobar barfoo last line I want the output to be, foo bar foobar I know it could be possible through the combination of tac and sed or tac and awk $ tac file | sed '1,3d' | tac foo bar foobar $ tac file | awk 'NR==1{next}NR==2{next}NR==3{next}1' | tac foo bar foobar But i want the output through awk only.

    Read the article

  • Uploading.to Uploads Files to Multiple File Hosts Simultaneously

    - by Jason Fitzpatrick
    If you’re looking to quickly share a file across a variety of file hosting services, Uploading.to makes it a cinch to share up to 10 files across 14 hosts. The upload process is simple. Visit Uploading.to, select your files, check the hosts you want to share the file across (by default all 14 are checked), add a description to the collection, and hit the Upload button. Uploading.to will upload your file to the various hosts; during the process you’ll see which hosts are confirmed and which have failed. We had 2 failures among the 14 hosts which still left the file mirrored across a sizable 12 host spread–not bad at all. When you’re ready to share the file hit the Copy Link button at the bottom of the screen and share it with your friends. They’ll be directed to Uploading.to and will be able to select from any of the hosts the file was successfully mirrored across. Uploading.to is a free service and requires no registration. Uploading.to [via Addictive Tips] HTG Explains: Do You Really Need to Defrag Your PC? Use Amazon’s Barcode Scanner to Easily Buy Anything from Your Phone How To Migrate Windows 7 to a Solid State Drive

    Read the article

  • LibreOffice - Can't drag and replace images [LibreOffice 3.5 and 3.6, Ubuntu 12.04]

    - by Anderxale
    My wife uses LibreOffice to create catalogues of a couple hundred items and then converts it to PDF. Man we love LibreOffice! Anyway I set up Windows-7 and Mint-14-Mate dual boot for her to ease into Linux. Today she was ready for Ubuntu and so I did a clean install on her machine. Everything was smooth but today when she tried to work she ran into an issue... She used to be able to download a folder full of images to use in her catalogues and then update her catalogues by replacing old images with new ones. It was so simple - Open an old catalogue, save with a new date, drag and drop replace images of items that no longer exist. The drag and drop process would scale the image and then crop it horizontally or vertically to fit. Now that I have installed Ubuntu 12.04 for her she can no longer replace images, it just does nothing... If she drags the image to the left or right of the original it appears next to the original so I know d&d works, unfortunately it does not resize or crop the image. I tried this on my laptop and my desktop... same thing! I then tried updating the LibreOffice to 3.6, no change. I then tried opening a virtual machine windows xp and Mint 14 on this computer and tried with 3.6 in those operating systems and it worked. Can anyone help? I have a lot of hope that there is an answer because Mint is based on Ubuntu/Debian and that distro can perform this task successfully! Sorry about writing a book....

    Read the article

  • 12.04 Black screen with blinking cursor

    - by Junaid
    I have read this post My computer boots to a black screen, what options do I have to fix it? UBUNTU 12.04 works well with livecd but fails to start after complete installation, black screen with a blinking cursor. I tried holding shift key and edit grub options but holding shift did not do anything. I give up, any suggestion. I have built in intel graphics card and an nvidia card in PCI. I have tried by removing nvidia card as well. All I see is a black screen with a blinking cursor. My system is Dell optiplex GX260 with 1GB ram and 2.4 GHz P4 processor

    Read the article

  • Configure EVDO USB Modem in Ubuntu 10.10

    - by adisembiring
    I want to configure EVDO Usb Modem in Ubuntu 10.10 I insert my usb modem to laptop and check the usb is detected or not using $sudo lsusb and the result is: Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 201e:2009 Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 14cd:6600 Super Top USB 2.0 IDE DEVICE Bus 002 Device 002: ID 201e:2009 is my us device. and than I execute command $dmesg | grep -e tty [ 0.000000] console [tty0] enabled [ 818.054660] usb 2-1.3: GSM modem (1-port) converter now attached to ttyUSB0 [ 818.055125] usb 2-1.3: GSM modem (1-port) converter now attached to ttyUSB1 [ 818.055647] usb 2-1.3: GSM modem (1-port) converter now attached to ttyUSB2 [ 818.330641] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 818.330743] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 818.330840] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2 [ 1054.917473] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB0 [ 1054.917995] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB1 [ 1054.918481] usb 2-1.2: GSM modem (1-port) converter now attached to ttyUSB2 [ 1055.214087] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0 [ 1055.214221] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1 [ 1055.214356] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2 Why converter disconnected from ttyUSB2 ? and than I try to execute command $sudo wvdialconf sorry, no modem was detected! Is it in use by another program ? did you configure it properly with setserials ? I change the same type usb modem from my friend, but I still get error above.

    Read the article

  • Properly Label Your Dangerous Projects

    - by Jason Fitzpatrick
    In the pursuit of science, fun, and laser-fueled hijinks, we often undertake projects that really should be labeled more properly. Download this effective label to visually warn “No really, you’ll burn the house down”. Courtesy of Flattr at Thingiverse, you can grab a copy of the “Warning: Will Burn Your House Down” graphic in high resolution image formats suitable for silk screening, laser engraving, or plain old fashioned sign printing. Warning: Will Burn Your House Down [Thingiverse via Make] How To Encrypt Your Cloud-Based Drive with BoxcryptorHTG Explains: Photography with Film-Based CamerasHow to Clean Your Dirty Smartphone (Without Breaking Something)

    Read the article

  • Cannot mount Android phone in Ubuntu and sync with Banshee

    - by Brett Alton
    I can't get my LG Optimus One to sync with Banshee. I read somewhere that the root needs to have an empty file called '.is_audio_player'. I did that and it still doesn't mount. I ran dmesg however and it appears that the card is unmounting before I even have a change to run Banshee. [ 7250.321359] usb 1-1.4: new high speed USB device using ehci_hcd and address 10 [ 7250.444795] scsi12 : usb-storage 1-1.4:1.0 [ 7251.567946] scsi 12:0:0:0: Direct-Access Multiple Card Reader 1.00 PQ: 0 ANSI: 0 [ 7251.568839] sd 12:0:0:0: Attached scsi generic sg3 type 0 [ 7252.232433] sd 12:0:0:0: [sdc] 15564800 512-byte logical blocks: (7.96 GB/7.42 GiB) [ 7252.233299] sd 12:0:0:0: [sdc] Write Protect is off [ 7252.233306] sd 12:0:0:0: [sdc] Mode Sense: 03 00 00 00 [ 7252.233309] sd 12:0:0:0: [sdc] Assuming drive cache: write through [ 7252.235658] sd 12:0:0:0: [sdc] Assuming drive cache: write through [ 7252.235666] sdc: sdc1 [ 7252.239132] sd 12:0:0:0: [sdc] Assuming drive cache: write through [ 7252.239140] sd 12:0:0:0: [sdc] Attached SCSI removable disk [ 7272.573437] usb 1-1.4: USB disconnect, address 10 Suggestions?

    Read the article

  • Mathematica 8 crashes Ubuntu 13.10

    - by Georgy Ivanov
    I have Mathematica 8 installed on my Ubuntu laptop since 2011. I updated Ubuntu several times, and experienced no problems with Mathematica. It also worked smoothly after I updated Ubuntu to 13.10 (it worked for sure for a week after update). When I tried to start Mathematica today by executing a .sh-file, the screen went black, I was logged out from the session and thrown back to the login screen. Typing mathematica in the terminal produced the same effect. Typing mathematica -cleanstart or mathematica -mesa did not help. Starting Gnome session with or without effects did not help Launching mathematica under another user account did not help. I still can run text-only version of mathematica by typing math in the terminal. I don't remember making any changes to my configuration except for installing updates. Is there any quick way to fix this behavior? How can I know which component exactly crashed? Where should I look for crash logs?

    Read the article

  • Google Chrome freezes for seconds

    - by Levan
    I do not know if this is the right place to write about google chrome or not so sorry if it is not after the update ,,Google Chrome 20.0.1132.47" google chrome started to lag ,,It gets stuck for couple of seconds and then it resumes" i think it starts lagging when i enter any flash site when i started chrome from the terminal it showed this before the update non of this appeared ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_direct.c:980:(snd1_pcm_direct_initialize_slave) unable to install hw params ALSA lib pcm_dsnoop.c:623:(snd_pcm_dsnoop_open) unable to initialize slave ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_direct.c:980:(snd1_pcm_direct_initialize_slave) unable to install hw params ALSA lib pcm_dsnoop.c:623:(snd_pcm_dsnoop_open) unable to initialize slave ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_direct.c:980:(snd1_pcm_direct_initialize_slave) unable to install hw params ALSA lib pcm_dsnoop.c:623:(snd_pcm_dsnoop_open) unable to initialize slave ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_direct.c:980:(snd1_pcm_direct_initialize_slave) unable to install hw params ALSA lib pcm_dsnoop.c:623:(snd_pcm_dsnoop_open) unable to initialize slave ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_direct.c:980:(snd1_pcm_direct_initialize_slave) unable to install hw params ALSA lib pcm_dsnoop.c:623:(snd_pcm_dsnoop_open) unable to initialize slave ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_direct.c:980:(snd1_pcm_direct_initialize_slave) unable to install hw params ALSA lib pcm_dsnoop.c:623:(snd_pcm_dsnoop_open) unable to initialize slave Firefox does not have any problem is there a way to fix this and thank you for your time

    Read the article

  • Issues with ganglia and upstart in 13.04

    - by theist
    I'm having an issue with ganglia-monitor and upstart. Just after installing it starts and it cannot be stopped. I tried to solve it following http://upstart.ubuntu.com/cookbook/#expect but I can achieve upstart to track the actual pid of gmond. Assuming the configuration of the init config is wrong i followed direcetions in http://upstart.ubuntu.com/cookbook/#how-to-establish-fork-count in order to try to fix it. As it states a count of 1 means "exec fork" stanza and 2 means "exec daemon" .... gmond gives a count of 8... And of course I can get it to track the actual PID. I haven't found a bug report or something like that. Is there something I missed ? Upstart seems to be failing and the worst thing is that upstart hangs on start/stop and I cannot even uninstall or reconfigure packages.

    Read the article

  • Dual booting 12.10 and Win 7 - boots directly to Win 7

    - by user110174
    and thank you kindly for you help! I'll preface this with saying that I realize this is a common problem, with lots of trouble-shooting guides available online; however, after multiple attempts with different guides, I've made zero progress and am hoping to someone could help me with my specific scenario. First, my story: -Initially, I installed Ubuntu 12.10 with the "Something Else" option with no problems. Used 4 GB Swap Logical Partition, 26 GB Primary Root Partition. Wanting to trying out Mint 13, I booted into Windows from GRUB2, used the latest version of EasyBCD (v2.2) to restore the Windows 7 bootloader to the MBR, deleted the Ubuntu partitions, reformatted them in NTFS. I then created a 30 GB partition of free space for Mint. I installed Mint using the same partitioning described above for Ubuntu 12.10, using /dev/sda for the boot installation files, and everything seemed to go well, until I re-booted my computer and it went straight to Windows - I could find no way to get into Mint. So I went into windows, restored windows bootloader to the MBR w/ EasyBCD, deleted partitions, etc., as I figured I'd done enough messing around and would go with Ubuntu 12.10. Now the problem: I restarted my computer booting from the same Ubuntu USB key I originally used. Briefly, "error: "prefix" is not set" flashed on screen, and instead of being greeted with the GUI menu of "try vs. install Ubuntu", there was a menu with minimal graphics (like a BIOS menu) where I could select install, run from USB, etc. After selecting "Install Ubuntu", the familiar install wizard with a GUI came up, I partitioned my drive as described, /dev/sda for the boot installation files, install went well, rebooted and...straight to Windows. This is where I'm at. Fixes I've tried: -This guide: How can I repair grub? (How to get Ubuntu back after installing Windows?) to ensure Grub is on the MBR. I followed all steps, but still when I reboot, I go directly into Windows. -Installing 12.04 instead of 12.10 - same issue -Re-installed Ubuntu, writing the boot files to their own partition, then using EasyBCD to to add a boot option for Ubuntu using the Windows bootloader, ensuring I instruct EasyBCD to look at the partition I created with the Ubuntu installer (instructions here http://neosmart.net/wiki/display/EBCD/Ubuntu). When I reboot, I select the Ubuntu option, and it puts me in GRUB4DOS, with a cursor waiting for input. I have no idea what to put here, so I would just type "reboot" to exit out. And this is where I am now. Any clue as to why I can't boot into Ubuntu? My computer specs are: ASUS UX31A Core i7, Win 7 64 Pro, 256 GB SSD, Intel HM76 Chipset and Integrated Intel HD 4000 Graphics, 4 GB memory I've tried to be as clear as possible, but I'd be happy to provide any info that would help anyone along. Thanks for your patience in reading this! Sincerely, -MN

    Read the article

  • Grub not showing on startup for Windows 8.1 Ubuntu 13.10 Dual boot

    - by driftking96
    K im so a newbie to Ubuntu and i bought a Windows 8 pre-installed laptop last month. I updated to Windows 8.1 and then i thought about installing Ubuntu as a dual boot so i could mess around and learn more about it. So i followed a Youtube tutorial ( http://www.youtube.com/watch?v=dJfTvkgLqfQ ). And i got my stuff working fine. The first few times i booted i got the GRUB menu instead of my default HP Boot OS Manager, and i was able to select my OS. So i went to sleep and the next day i turned on my computer and the GRUB menu did not show up. I tried several times and it didnt automatically show up. In order for me to see the GRUB menu i had to turn on my PC and on start had to press ESC to pause startup and press F9 to get boot options. Then from there i had to pick from OS Boot, Ubuntu, Ubuntu (Yes there were two Ubuntus available) and a default EFI file thingy. When i click the first Ubuntu i get the GRUB Menu (I was too scared to try the second incase i screwed my laptop up) and i can safely load Ubuntu from there and use it (although i do have to increase my brightness everytime i load Ubuntu bec it somehow reduces my brightness to complete darkness on boot) So my problem here is why isnt my GRUB showing on boot, after it worked on the first day? I was on Windows 8.1 while typing this and if you have any questions or answers, i will happily answer or use them as a solution to the best of my abilities. BTW my laptop is a HP TouchSmart j-078CA.

    Read the article

  • Problem with apt-get update: failed to fetch error

    - by user171447
    I run an Ubuntu Server 12.04.3 LTS. Today, I wanted to update it, but I did not managed it (yes...), however upgrading worked well. I don't want you to solve my problem but it would be greatful if you could give me some hints. I googled hours, I fould a lot of this kind of errors, but not exactly this. Here is the output of apt-get update: Hit http://filepile.fastit.net precise Release.gpg Hit http://filepile.fastit.net precise Release Hit http://filepile.fastit.net precise/main amd64 Packages Hit http://filepile.fastit.net precise/restricted amd64 Packages Hit http://filepile.fastit.net precise/universe amd64 Packages Hit http://filepile.fastit.net precise/multiverse amd64 Packages Hit http://filepile.fastit.net precise/main i386 Packages Hit http://filepile.fastit.net precise/restricted i386 Packages Hit http://filepile.fastit.net precise/universe i386 Packages Hit http://filepile.fastit.net precise/multiverse i386 Packages Ign http://filepile.fastit.net precise/main TranslationIndex Ign http://filepile.fastit.net precise/multiverse TranslationIndex Ign http://filepile.fastit.net precise/restricted TranslationIndex Ign http://filepile.fastit.net precise/universe TranslationIndex Ign http://filepile.fastit.net precise/main Translation-en_GB Ign http://filepile.fastit.net precise/main Translation-en Ign http://filepile.fastit.net precise/main Translation-en_GB.UTF-8 Hit http://archive.canonical.com precise Release.gpg Ign http://filepile.fastit.net precise/multiverse Translation-en_GB Ign http://filepile.fastit.net precise/multiverse Translation-en Ign http://filepile.fastit.net precise/multiverse Translation-en_GB.UTF-8 Ign http://filepile.fastit.net precise/restricted Translation-en_GB Ign http://filepile.fastit.net precise/restricted Translation-en Ign http://filepile.fastit.net precise/restricted Translation-en_GB.UTF-8 Ign http://filepile.fastit.net precise/universe Translation-en_GB Ign http://filepile.fastit.net precise/universe Translation-en Ign http://filepile.fastit.net precise/universe Translation-en_GB.UTF-8 Hit http://archive.ubuntu.com precise Release.gpg Hit http://archive.canonical.com precise Release Hit http://archive.ubuntu.com precise Release Hit http://archive.ubuntu.com precise/main Sources Hit http://archive.ubuntu.com precise/restricted Sources Hit http://archive.ubuntu.com precise/main i386 Packages Hit http://archive.ubuntu.com precise/restricted i386 Packages Hit http://archive.ubuntu.com precise/multiverse i386 Packages Hit http://archive.ubuntu.com precise/main TranslationIndex Hit http://archive.ubuntu.com precise/multiverse TranslationIndex Hit http://archive.ubuntu.com precise/restricted TranslationIndex Hit http://archive.ubuntu.com precise/main Translation-en_GB Hit http://archive.ubuntu.com precise/main Translation-en Hit http://archive.ubuntu.com precise/multiverse Translation-en_GB Hit http://archive.ubuntu.com precise/multiverse Translation-en Hit http://archive.ubuntu.com precise/restricted Translation-en_GB Hit http://archive.ubuntu.com precise/restricted Translation-en Hit http://fr.archive.ubuntu.com precise-security Release.gpg Hit http://fr.archive.ubuntu.com precise-updates Release.gpg Hit http://fr.archive.ubuntu.com precise-security Release Hit http://fr.archive.ubuntu.com precise-updates Release Hit http://fr.archive.ubuntu.com precise-security/main amd64 Packages Hit http://fr.archive.ubuntu.com precise-security/restricted amd64 Packages Hit http://fr.archive.ubuntu.com precise-security/universe amd64 Packages Hit http://fr.archive.ubuntu.com precise-security/multiverse amd64 Packages :W: Failed to fetch http://archive.canonical.com/dists/precise/Release Unable to find expected entry 'main/binary-amd64/Packages' in Release file (Wrong sources.list entry or malformed file) E: Some index files failed to download. They have been ignored, or old ones used instead. Hit http://fr.archive.ubuntu.com precise-security/main i386 Packages Hit http://fr.archive.ubuntu.com precise-security/restricted i386 Packages Hit http://fr.archive.ubuntu.com precise-security/universe i386 Packages Hit http://fr.archive.ubuntu.com precise-security/multiverse i386 Packages Hit http://fr.archive.ubuntu.com precise-security/main TranslationIndex Hit http://fr.archive.ubuntu.com precise-security/multiverse TranslationIndex Hit http://fr.archive.ubuntu.com precise-security/restricted TranslationIndex Hit http://fr.archive.ubuntu.com precise-security/universe TranslationIndex Hit http://fr.archive.ubuntu.com precise-updates/main amd64 Packages Hit http://fr.archive.ubuntu.com precise-updates/restricted amd64 Packages Hit http://fr.archive.ubuntu.com precise-updates/universe amd64 Packages Hit http://fr.archive.ubuntu.com precise-updates/multiverse amd64 Packages Hit http://fr.archive.ubuntu.com precise-updates/main i386 Packages Hit http://fr.archive.ubuntu.com precise-updates/restricted i386 Packages Hit http://fr.archive.ubuntu.com precise-updates/universe i386 Packages Hit http://fr.archive.ubuntu.com precise-updates/multiverse i386 Packages Hit http://fr.archive.ubuntu.com precise-updates/main TranslationIndex Hit http://fr.archive.ubuntu.com precise-updates/multiverse TranslationIndex Hit http://fr.archive.ubuntu.com precise-updates/restricted TranslationIndex Hit http://fr.archive.ubuntu.com precise-updates/universe TranslationIndex Hit http://fr.archive.ubuntu.com precise-security/main Translation-en Hit http://fr.archive.ubuntu.com precise-security/multiverse Translation-en Hit http://fr.archive.ubuntu.com precise-security/restricted Translation-en Hit http://fr.archive.ubuntu.com precise-security/universe Translation-en Hit http://fr.archive.ubuntu.com precise-updates/main Translation-en_GB Hit http://fr.archive.ubuntu.com precise-updates/main Translation-en Hit http://fr.archive.ubuntu.com precise-updates/multiverse Translation-en_GB Hit http://fr.archive.ubuntu.com precise-updates/multiverse Translation-en Hit http://fr.archive.ubuntu.com precise-updates/restricted Translation-en_GB Hit http://fr.archive.ubuntu.com precise-updates/restricted Translation-en Hit http://fr.archive.ubuntu.com precise-updates/universe Translation-en_GB Hit http://fr.archive.ubuntu.com precise-updates/universe Translation-en And here is my /etc/apt/sources.list: ###### Ubuntu Main Repos deb http://filepile.fastit.net/ubuntu/ precise main restricted universe multiverse # deb http://de.archive.ubuntu.com/ubuntu/ precise main restricted universe multiverse deb http://archive.canonical.com/ precise main restricted universe multiverse ###### Ubuntu Update Repos deb http://fr.archive.ubuntu.com/ubuntu/ precise-security main restricted universe multiverse deb http://fr.archive.ubuntu.com/ubuntu/ precise-updates main restricted universe multiverse deb http://archive.ubuntu.com/ubuntu/ precise main restricted multiverse deb-src http://archive.ubuntu.com/ubuntu precise main restricted multiverse Thanks for your help!

    Read the article

  • How to check if a Webcam is broken?

    - by user84812
    I just bought an Acer Aspire 3830TG, it comes with an integrated 1.3M HD Webcam. Before buying it i tried with a bootable Lubuntu usb stick, everything worked well except for the webcam, which i thought I had to tweak. The thing is that it seems the camera should work with no problems in ubuntu. The driver is detected, I try dmesg | grep uvcvideo and the output is [ 12.226174] uvcvideo: Found UVC 1.00 device 1.3M HD WebCam (058f:b002) [ 12.245553] usbcore: registered new interface driver uvcvideo I've also tried using different software (guvcview is black when camera output is MJPG and turns to funny colors when YU12 or YV12, cheese is always black, camorama is always with funny colors...). I should have checked that it was working properly with the default os (windows) but now it's too late for that. I even booted with a official Ubuntu Quantal distro from the usb pen, and the results are the same. so, my question is: is there any way to check that the camera is righmt or broken? So, if it's broken, at least i can go to the shop, show them that it's really broken and get an external webcam for free, or st like that. cheers. UPDATE 1 Thanks, jrp. I run sudo lsinput, and the output info about my video is the following: /dev/input/event6 bustype : BUS_USB vendor : 0x58f product : 0xb002 version : 2 name : "1.3M HD WebCam" phys : "usb-0000:00:1a.0-1.3/button" bits ev : EV_SYN EV_KEY /dev/input/event7 bustype : BUS_HOST vendor : 0x0 product : 0x6 version : 0 name : "Video Bus" phys : "LNXVIDEO/video/input0" bits ev : EV_SYN EV_KEY With this info, i'm not pretty sure about running the luvcview command. If I run luvcview -d /dev/video0 -L, the output is the following: SDL information: Video driver: x11 A window manager is available Device information: Device path: /dev/video0 { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/7, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/7, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/7, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/7, 1/5, { pixelformat = 'MJPG', description = 'MJPEG' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, { pixelformat = 'RGB3', description = 'RGB3' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, { pixelformat = 'BGR3', description = 'BGR3' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, { pixelformat = 'YU12', description = 'YU12' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, { pixelformat = 'YV12', description = 'YV12' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 160, height = 120 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 176, height = 144 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 320, height = 240 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 352, height = 288 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 720 } Time interval between frame: 1/30, 1/25, 1/20, 1/15, 1/10, 1/5, { discrete: width = 1280, height = 800 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 960 } Time interval between frame: 1/15, 1/10, 1/5, { discrete: width = 1280, height = 1024 } Time interval between frame: 1/15, 1/10, 1/5, if i run luvcview by itself, the image is funny (blue and red colors, mainly, with myself in negative state). tx

    Read the article

  • How to Create Custom Cover Pages in Microsoft Word 2010

    - by Zainul Franciscus
    A great cover page draws readers, and if you know Word, then you are in luck, because Word gives ready to use cover pages. But did you know that Word lets you create your own cover pages? Head over to the “Insert” ribbon and you’ll find that Microsoft Office gives some cover pages that you can use. Although, normally a cover page appears in the first page, Word lets you place the cover page anywhere in the document. How to Make and Install an Electric Outlet in a Cabinet or DeskHow To Recover After Your Email Password Is CompromisedHow to Clean Your Filthy Keyboard in the Dishwasher (Without Ruining it)

    Read the article

  • Can it be harmful to grant jackd realtime priority?

    - by SuperElectric
    I am apt-get installing Ardour, a sound mixing program, just to try it out. Installing Ardour also installs JACK, a dependency. As part of the JACK installation script, I get the following dialog: If you want to run jackd with realtime priorities, the user starting jackd needs realtime permissions. Accept this option to create the file /etc/security/limits.d/audio.conf, granting realtime priority and memlock privileges to the audio group. Running jackd with realtime priority minimizes latency, but may lead to complete system lock-ups by requesting all the available physical system memory, which is unacceptable in multi-user environments. Enable realtime process priority? I'm installing on my laptop, which never has multiple simultaneous users. I still have concerns: is JACK something that'll be used by the system itself to play any sound (i.e. will it replace ALSA)? If so, does that mean that if I enable realtime priority for JACK, I'll run a slight risk of freezing the machine whenever any sound is played? Or is JACK only going to be used by Ardour for now (until I install some other JACK-dependent program)? Thanks, -- Matt

    Read the article

  • How to correctly install the latest Mono, Moonlight and Monodevelop instead of the version in Ubuntu repository?

    - by Ivan
    I would like to have the latest stable (2.8) Mono stack (Mono, Moonlight with Firefox plugin, Monodevelop, Monodoc, etc) on Ubuntu 10.10 not have any remains of old Mono 2.6 which is available in Ubuntu repos, get all the mono-depending packages satisfied (I am afraid they will complain if I don't install Mono 2.6 from packages and install manually downloaded Mono 2.8 instead) How do I acheive this?

    Read the article

  • Problems with updates

    - by legospace9876
    I can not update Weather Indicator with Update Manager. This is the terminal log: installArchives() failed: perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "sr_RS.utf_8_latin" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "sr_RS.utf_8_latin" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "sr_RS.utf_8_latin" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LANG = "sr_RS.utf_8_latin" are supported and installed on your system. perl: warning: Falling back to the andard locale ("C"). locale: Cannot set LC_CTYPE to default locale: No such file or directory locale: Cannot set LC_MESSAGES to default locale: No such file or directory locale: Cannot set LC_ALL to default locale: No such file or directory Setting up indicator-weather (11.11.28-0ubuntu1.1) ... Installing indicator-specific icons... Installing indicator dconf schema... cp: cannot stat `/usr/share/indicator-weather/indicator-weather.gschema.xml': No such file or directory dpkg: error processing indicator-weather (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: indicator-weather Error in function: SystemError: E:Sub-process /usr/bin/dpkg returned an error code (1) Setting up indicator-weather (11.11.28-0ubuntu1.1) ... Installing indicator-specific icons... Installing indicator dconf schema... cp: cannot stat `**/usr/share/indicator-weather/indicator-weather.gschema.xml**': No such file or directory dpkg: error processing indicator-weather (--configure): subprocess installed post-installation script returned error exit status 1 The file that I bold really does not exist. How can I solve this problem?

    Read the article

< Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >