Search Results

Search found 5472 results on 219 pages for 'faceless1 14'.

Page 146/219 | < Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >

• how to setup a bridge with 2 NICs and few virtual machines

  - by Bond

  Here is my situation. I have a server with 2 NICs. I have installed virtual box and I have created a few Guest Operating Systems on it. I want these Virtual Machines to be using a bridge.NIC2 would be used to setup this bridge and NIC1 would be connected to corporate network.I am not clear with how should I go on doing this. /etc/network/interfaces is the file which I am trying to modify etc. My approach is following 1) Define a configuration file /etc/network/interfaces 2) Create IPTABLES as how NIC1 will forward the packets to Bridge on NIC2 Now comes the problem I do not understand what is the meaning of following lines in the configuration file auto lo iface lo inet loopback # The primary network interface auto eth2 iface eth2 inet manual auto br0 iface br0 inet static address 192.168.1.14 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.10 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 192.168.13.2 dns-search myserver.net bridge_ports eth2 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off So any pointers to what should be the entries of /etc/network/interfaces file. So that I understand which parameter is to be used when and where that would help me.

  Read the article

• Slowdown upon router/modem setup change

  - by Ollie Saunders

  I’ve been using a Belkin FSD7632-4 modem router to connect to my TalkTalk provided ADSL internet connection for some time and been pretty happy with it. Recently, however, the connection has been failing and I decided to get a ASUS RT-N16 instead, which is also a much more capable router generally. The ASUS RT-N16 doesn’t come with a modem built-in so I purchased as Zoom modem as well. I’ve set them both up and am using them to post this message. But I’m a bit miffed to find that I get a significantly and consistently slower downstream rate from the new configuration than with the old Belkin. Belkin modem router: downstream: 3.45 mbps upstream: 0.73 mbps ASUS router + Zoom modem: downstream: 2.71 mbps upstream: 0.66 mbps Any ideas why this is? The really weird thing about this is that the Zoom supports ADSL2 and ADSL2+ but I don’t think the old Belkin does. At first I thought it might be due to the Zoom modem being limited to PPPoE instead of PPPoA, which my ISP supports, but then I tried using PPPoE with the Belkin and that still gave a high speed. I’m using VC-Mux encapsulation with both. VPI of 0 and VCI of 38. I pulled this data off the Zoom: Mode: ADSL2 Line Coding: Trellis On Status: No Defect Link Power State: L0 Downstream Upstream SNR Margin (dB): 12.3 11.8 Attenuation (dB): 43.0 24.9 Output Power (dBm): 12.9 0.0 Attainable Rate (Kbps): 3936 844 Rate (Kbps): 3194 840 MSGc (number of bytes in overhead channel message): 59 10 B (number of bytes in Mux Data Frame): 99 14 M (number of Mux Data Frames in FEC Data Frame): 2 16 T (Mux Data Frames over sync bytes): 1 8 R (number of check bytes in FEC Data Frame): 8 8 S (ratio of FEC over PMD Data Frame length): 1.9833 9.0594 L (number of bits in PMD Data Frame): 839 219 D (interleaver depth): 32 2 Delay (msec): 15 4 Super Frames: 15808 14078 Super Frame Errors: 0 4294967232 RS Words: 513778 111753 RS Correctable Errors: 126 4294967238 RS Uncorrectable Errors: 0 N/A HEC Errors: 0 4294967279 OCD Errors: 0 0 LCD Errors: 0 0 Total Cells: 1920175 237597 Data Cells: 205993 392 Bit Errors: 0 0 Total ES: 0 0 Total SES: 0 0 Total UAS: 34 0

  Read the article

• Using ACK to list directories

  - by KPthunder

  I have a directory listing as follows (given by ls -la): total 8 drwxr-xr-x 6 <user> <group> 204 Oct 18 12:13 . drwxr-xr-x 7 <user> <group> 238 Oct 18 11:29 .. drwxr-xr-x 14 <user> <group> 476 Oct 18 12:31 .git -rw-r--r-- 1 <user> <group> 601 Oct 18 12:03 index.html drwxr-xr-x 2 <user> <group> 68 Oct 18 12:13 test drwxr-xr-x 2 <user> <group> 68 Oct 18 12:13 test2 Running ack . -f prints out the files in the directory: index.html How can I get ack to print out the directories in the directory? I want to ignore the .git directory (which I understand is default behavior for ack). On that note, how can I ignore certain directories? I am using ack 1.9.6 on Mac OSX 10.8.2.

  Read the article

• WRT54GL Tomato Router in Client wireless mode to an iPhone Personal Hotspot

  - by Gordo

  I am trying to connect a router with Tomato firmware to an iPhone 4. The goal is to connect to the Personal Hotspot in Client Wireless mode. This should allow wired and wireless users to connect to the router rather then the iPhone. In theory this should be possible but I am having difficulty. Router Linksys WRT54GL Tomato 1.28.1816 firmware iPhone iPhone 4 iOS 5.1 (9B176) Carrier Rogers Wireless Personal Hotspot works with other devices, wifi/bluetooth/usb iPhone Personal Hotspot settings Mode: B/G Security: WPA or WPA2 Personal Encryption: AES Router IP: 172.20.10.1 Subnet: 172.20.10.0 Min IP: 172.20.10.2 Max IP: 172.20.10.14 maximum number of wireless tethered hosts is 5 I have followed the directions here: http://www.wi-fiplanet.com/tutorials/article.php/3810281 Ensured that the router subnet does not 'collide' with the iPhone subnet. Here is the configuration of the Tomato 'Basic - Network - Wireless' section: http://i.stack.imgur.com/pbmTB.png I have tried several variations of this configuration, but nothing seems to work. NOTE: I have successfully connected to my own wifi network in Wireless Client mode, so I am confident that there are no bad cables or other hardware issues. I would prefer to use Tomato, but DD-WRT maybe my only other option. Thanks!

  Read the article

• Preventing DDOS/SYN attacks (as far as possible)

  - by Godius

  Recently my CENTOS machine has been under many attacks. I run MRTG and the TCP connections graph shoots up like crazy when an attack is going on. It results in the machine becoming inaccessible. My MRTG graph: mrtg graph This is my current /etc/sysctl.conf config # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 1 # Controls whether core dumps will append the PID to the core filename # Useful for debugging multi-threaded applications kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Controls the maximum size of a message, in bytes kernel.msgmnb = 65536 # Controls the default maxmimum size of a mesage queue kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_syncookies = 1 net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.accept_redirects = 0 net.ipv6.conf.all.accept_redirects = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_source_route = 0 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_max_syn_backlog = 1280 Futher more in my Iptables file (/etc/sysconfig/iptables ) I only have this setup # Generated by iptables-save v1.3.5 on Mon Feb 14 07:07:31 2011 *filter :INPUT ACCEPT [1139630:287215872] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1222418:555508541] Together with the settings above, there are about 800 IP's blocked via the iptables file by lines like: -A INPUT -s 82.77.119.47 -j DROP These have all been added by my hoster, when Ive emailed them in the past about attacks. Im no expert, but im not sure if this is ideal. My question is, what are some good things to add to the iptables file and possibly other files which would make it harder for the attackers to attack my machine without closing out any non-attacking users. Thanks in advance!

  Read the article

• Certificates required for WHQL-certified drivers

  - by Kasius

  The 64-bit Windows 7 image that we deploy to machines at our site does not contain all of the certificates included on a default Windows image. Automatic root certificate installation is also disabled per policy from higher in the organization. We have had a lot of trouble installing many WHQL-certified drivers from reputable companies (ex. HP, Lexmark, Dell, etc.), and I hypothesize that a required certificate is missing from one of the certificate stores on the machine. The error we typically get is: The driver cannot be installed because it is either not digitally signed or not signed in the appropriate manner. I know that it is signed. A .CAT file is included, and it has the following tree from top to bottom: Microsoft Root Authority (thumbprint a4 34 89 15 9a 52 0f 0d 93 d0 32 cc af 37 e7 fe 20 a8 b4 19) Microsoft Windows Hardware Compatibility PCA (thumbprint 93 b8 d8 82 0a 32 db 20 a5 ea b6 8d 86 ad 67 8e fa 14 ea 41) Microsoft Windows Hardware Compatibility Publisher (thumprint b0 50 45 45 42 4e be 2c 16 2f 62 5b bf 5a e6 9b 96 bf 0b 0b) What certificates are required to install WHQL-certified drivers? Is it possibly something other than certificates? Thanks! NOTE: I have posted this question on Technet as well, but honestly, I've never had a lot of luck posting questions on the Technet forums.

  Read the article

• Ubuntu 9.10 RSA authentication: ssh fails, filezilla runs fine

  - by MariusPontmercy

  This is quite a mistery for me. I usually use passwordless RSA authentication to login into my remote *nix servers with ssh and sftp. Never had any problem until now. I cannot connect to an Ubuntu 9.10 machine: user@myclient$ ssh -i .ssh/Ganymede_key [email protected] [...] debug1: Host 'ganymede.server.com' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:14 debug2: bits set: 494/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: .ssh/Ganymede_key (0xb96a0ef8) debug2: key: .ssh/Ganymede_key ((nil)) debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering public key: .ssh/Ganymede_key debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Trying private key: .ssh/Ganymede_key debug1: read PEM private key done: type RSA debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password,keyboard-interactive debug2: we did not send a packet, disable method debug1: Next authentication method: keyboard-interactive debug2: userauth_kbdint debug2: we sent a keyboard-interactive packet, wait for reply debug2: input_userauth_info_req debug2: input_userauth_info_req: num_prompts 1 Then it falls back to password authentication. If I disable password authentication on the remote machine my connection attempt just fails with a "Permission denied (publickey)." state. Same thing for sftp from command line. The "funny" thing is that the exact same RSA key works like a charm with a Filezilla sftp session instead: 12:08:00 Trace: Offered public key from "/home/user/.filezilla/keys/Ganymede_key" 12:08:00 Trace: Offer of public key accepted, trying to authenticate using it. 12:08:01 Trace: Access granted 12:08:01 Trace: Opened channel for session 12:08:01 Trace: Started a shell/command 12:08:01 Status: Connected to ganymede.server.com 12:08:02 Trace: CSftpControlSocket::ConnectParseResponse() 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Status: Retrieving directory listing... 12:08:02 Trace: CSftpControlSocket::SendNextCommand() 12:08:02 Trace: CSftpControlSocket::ChangeDirSend() 12:08:02 Command: pwd 12:08:02 Response: Current directory is: "/root" 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Trace: CSftpControlSocket::ParseSubcommandResult(0) 12:08:02 Trace: CSftpControlSocket::ListSubcommandResult() 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Status: Directory listing successful Any thoughts? M

  Read the article

• SeLinux blocking connection to sshd on Ubuntu 9.10

  - by Barton Chittenden

  When I try to log on to my laptop, which runs Ubuntu 9.10, the server rejects my login attempts. Checking /var/log/auth.log, I see the following: Feb 14 12:41:16 tiger-laptop sshd[6798]: error: ssh_selinux_getctxbyname: Failed to get default SELinux security context for tiger I googled for this, and ran across the following: http://www.spinics.net/lists/fedora-.../msg13049.html Here's the part that I think relates to the problem that I'm having: Quote: What's wrong on my system? Why it's not possible to login even if selinux is in permissive mode? Any suggestions? I'd start by trying to figure out why sshd isn't running in sshd_t (it seems to be running in sysadm_t). Paul. selinux mailing list selinux@xxxxxxxxxxxxxxxxxxxxxxx https://admin.fedoraproject.org/mail...stinfo/selinux Yes, sshd is running in sysadm_t: ps axZ | grep sshd system_u:system_r:sysadm_t 3632 ? Ss 0:00 /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pi ls -Z /usr/sbin/sshd system_ubject_r:sshd_exec_t /usr/sbin/sshd Don't know why it's not sshd_t. I didn't modified something. It's a standard installation of sles11 with the default reference policy from tresys. Maybe this code snippet from policy/modules/services/ssh.te is responsible for that: Allow ssh logins as sysadm_r:sysadm_t gen_tunable(ssh_sysadm_login, true) Any ideas? Do you have boolean init_upstart set to on? if not try setting it to on. I do not believe ssh_sysadm_login boolean works currently but i may be mistaken. -- Yeah, setting init_upstart to on did the trick! THANK A LOT! Do you know why this prevents the user from logging in through ssh even if selinux is set to permissive?? Ok, so the million dollar question is "where do I set 'init_upstart=1'"? It's not clear from context which configuration file needs to be edited, and I'm not at all familiar with SELinux configuration.

  Read the article

• How can I pause console output in rxvt?

  - by Javid Jamae

  I'm running rxvt in Cygwin on a Windows box. This is how I invoke it: rxvt -sr -sl 2500 -sb -geometry 90x30 -tn rxvt -fn "Lucida Console-14" -e /usr/bin/bash --login -i Anyone know how to pause the console output in rxvt? I can use Ctrl-S / Ctrl-Q to pause / un-pause, but this won't work if a script is already running and spewing output to stdout. Highlighting the terminal window with the mouse doesn't seem to work like with other consoles such as the standard Cygwin console, or the Windows command prompt console. Some sort of scroll lock would be nice, but I can't seem to find any way to do this. I know I could just pipe my output to a file, but I want a way to pause the output for something that I didn't expect to explode with console output. Basically I want to scroll back while its running without it constantly moving me to the bottom of the output buffer as it updates more data to stdout. I don't particularly care if the solution given actually pauses the script (like when you highlight the mouse in the Windows Command window), or just scroll locks and let's me scroll while its still running the underlying script, though I'd like to know how to do both if its possible.

  Read the article

• Application for time and project management

  - by user10826

  I want to improve the way I organize my projects/tasks/schedule What I do now is: keep an excel sheet with the name of the most important tasks/projects, I look at it at the beginning of each day and decide the ones I will focus on on iCal I write down events for each day, or for a concrete time (13 to 14 hours). I set up each day the tasks I want to accomlish, and allocate them hours I use Things (culture code) to keep info about tasks and projects not very important and which are not time allocated yet (GTD name = someday) I use Mail on Mac and create folders for the mails I want to process with the name of the different projects I save the main info for each project on freemind maps My system works well at the moment but it is pretty complicated to use. I want to make it better and I am looking for something with these requirements: must be 100% offline accessable it should use as less programs/resources as possible, ideally just one program should be able to manage all my info I can use the GTD methodology mixed with priorities and I can allocate each task converted to event on my calendar I can have different daily/weekly, etc views on a calendar to see the "big picture" must run on mac os x leopard price does not matter, I will pay for this So, according to your experience, can you recommend me something like this? Thanks

  Read the article

• Flash drive suddenly died. Why? Can I recover it?

  - by mg

  Hi, I have a flash drive that I used not too much but, after few month of inactivity, it died. I know that flash drives have a limited write cycles but I am sure that this is not the problem. I tried to create a new partition table and format the drive nothing worked. This is the output of mkfs.ext2. marco@pinguina:~$ sudo LANG=en.UTF-8 mkfs.ext2 -v -c /dev/sdc1 [sudo] password for marco: mke2fs 1.41.11 (14-Mar-2010) fs_types for mke2fs.conf resolution: 'ext2', 'default' Calling BLKDISCARD from 0 to 4001431552 failed. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 244320 inodes, 976912 blocks 48845 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=1002438656 30 block groups 32768 blocks per group, 32768 fragments per group 8144 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Running command: badblocks -b 4096 -X -s /dev/sdc1 976911 badblocks: Input/output error during ext2fs_sync_device Checking for bad blocks (read-only test): done Block 0 in primary superblock/group descriptor area bad. Blocks 0 through 2 must be good in order to build a filesystem. Aborting.... Is there something I can do to recover it?

  Read the article

• Flow of packet in network

  - by user58859

  I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN. When packet goes from router to local LAN, do it passes all the computers? Means did it goes to ehernet card of every computer and those computers accept the packet based on their physical address. To which pc the packet will go first? To the nearest to the router? What happen if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this? Thanks in advance.

  Read the article

• Bad performance with Linux software RAID5 and LUKS encryption

  - by Philipp Wendler

  I have set up a Linux software RAID5 on three hard drives and want to encrypt it with cryptsetup/LUKS. My tests showed that the encryption leads to a massive performance decrease that I cannot explain. The RAID5 is able to write 187 MB/s [1] without encryption. With encryption on top of it, write speed is down to about 40 MB/s. The RAID has a chunk size of 512K and a write intent bitmap. I used -c aes-xts-plain -s 512 --align-payload=2048 as the parameters for cryptsetup luksFormat, so the payload should be aligned to 2048 blocks of 512 bytes (i.e., 1MB). cryptsetup luksDump shows a payload offset of 4096. So I think the alignment is correct and fits to the RAID chunk size. The CPU is not the bottleneck, as it has hardware support for AES (aesni_intel). If I write on another drive (an SSD with LVM) that is also encrypted, I do have a write speed of 150 MB/s. top shows that the CPU usage is indeed very low, only the RAID5 xor takes 14%. I also tried putting a filesystem (ext4) directly on the unencrypted RAID so see if the layering is problem. The filesystem decreases the performance a little bit as expected, but by far not that much (write speed varying, but 100 MB/s). Summary: Disks + RAID5: good Disks + RAID5 + ext4: good Disks + RAID5 + encryption: bad SSD + encryption + LVM + ext4: good The read performance is not affected by the encryption, it is 207 MB/s without and 205 MB/s with encryption (also showing that CPU power is not the problem). What can I do to improve the write performance of the encrypted RAID? [1] All speed measurements were done with several runs of dd if=/dev/zero of=DEV bs=100M count=100 (i.e., writing 10G in blocks of 100M). Edit: If this helps: I'm using Ubuntu 11.04 64bit with Linux 2.6.38. Edit2: The performance stays approximately the same if I pass a block size of 4KB, 1MB or 10MB to dd.

  Read the article

• Proxmox drbd configuration split brain [on hold]

  - by AudioDan

  I am planning a proxmox HA configuration with two Dell R710 machines (dual 6 core processors in each) with enterprise level drive raid arrays. I would be using DRBD with a quorum disk on a third machine. I would dedicate two 1GB nics on each server to the DRBD communications. We would have approximately 12 to 14 Virtual Machines running on this pair of servers. The proxmox manual recommends creating two DRBD resources - one for the Virtual Machines that normally run on ServerA and one for the Virtual Machines that normally run on ServerB. This is because of the Primary/Primary state in which this configuration runs. If both servers have VMs talking to the same DRBD resource and a split brain situation occurs, there is potential for data corruption that must be resolved. While I understand it would take more effort to create new virtual machines, can anybody foresee any potential problems with running a separate DRBD resource for each VM instead? Does anyone have experience running a setup that way and has it worked well? It seems to me that would allow more flexibility in moving machines back and forth.

  Read the article

• Mailman delivery troubles

  - by stanigator

  I have apparently posted at the wrong place (superuser.com) for this question, so I'll just repost it here. Hope those of you who read both sites are not going to be offended. It's about mailing list management software called Mailman from GNU. Here are the details: Hosting provider: Vlexofree Domain: www.sysil.com with Google Apps Mailing List created from hosting cpanel: [email protected] I have registered a list of subscribers, and tried sending an email to [email protected]. I got the following error message: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550-5.1.1 The email account that you tried to reach does not exist. Please try 550-5.1.1 double-checking the recipient's email address for typos or 550-5.1.1 unnecessary spaces. Learn more at 550 5.1.1 http://mail.google.com/support/bin/answer.py?answer=6596 23si6479194ewy.44 (state 14). ----- Original message ----- MIME-Version: 1.0 Received: by 10.216.90.136 with SMTP id e8mr1469147wef.110.1264220118960; Fri, 22 Jan 2010 20:15:18 -0800 (PST) Date: Fri, 22 Jan 2010 20:15:18 -0800 Message-ID: <[email protected]> Subject: From: Stanley Lee <[email protected]> To: [email protected] Content-Type: multipart/alternative; boundary=0016e6dab0931bccc3047dcd2f1e - Show quoted text - Is there any way of fixing this problem? I would like to be able to have this mailing list to work through my hosting and domain. Thanks in advance.

  Read the article

• Unable to connect via NetBIOS Name

  - by grom

  I can't connect to machines/shares by NetBIOS names. Below is console output showing the problem. C:\>nbtstat -n Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Local Name Table Name Type Status --------------------------------------------- BEAST <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BEAST <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered WORKGROUP <1D> UNIQUE Registered ..__MSBROWSE__.<01> GROUP Registered C:\>nbtstat -A 192.168.1.3 Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] NetBIOS Remote Machine Name Table Name Type Status --------------------------------------------- BRCLAPTOP <00> UNIQUE Registered WORKGROUP <00> GROUP Registered BRCLAPTOP <20> UNIQUE Registered WORKGROUP <1E> GROUP Registered MAC Address = 00-1C-BF-14-B8-6E C:\>ping beast Pinging beast [fe80::59b8:179f:b90b:a63f%11] with 32 bytes of data: Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Reply from fe80::59b8:179f:b90b:a63f%11: time<1ms Ping statistics for fe80::59b8:179f:b90b:a63f%11: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms C:\>ping brclaptop Ping request could not find host brclaptop. Please check the name and try again. C:\>nbtstat -a brclaptop Local Area Connection: Node IpAddress: [192.168.1.100] Scope Id: [] Host not found.

  Read the article

• Varnish gets in a restart loop and causes the system to lock up; how can I fix?

  - by chrism2671

  Here is an extract from the syslog. Mar 2 14:01:10 ip-10-226-34-17 varnishd[20204]: Child (20205) not responding to ping, killing it. Mar 2 14:01:16 ip-10-226-34-17 varnishd[20204]: Child (20205) not responding to ping, killing it. Mar 2 14:01:16 ip-10-226-34-17 varnishd[20204]: Child (20205) died signal=3 Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child cleanup complete Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: child (13224) Started Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child (13224) said Closed fds: 4 5 6 10 11 13 14 Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child (13224) said Child starts Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child (13224) said managed to mmap 536870912 bytes of 536870912 Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child (13224) said Ready Mar 2 14:01:35 ip-10-226-34-17 varnishd[20204]: Child (13224) not responding to ping, killing it. Mar 2 14:02:10 ip-10-226-34-17 last message repeated 7 times Mar 2 14:03:15 ip-10-226-34-17 last message repeated 13 times Mar 2 14:03:20 ip-10-226-34-17 varnishd[20204]: Child (13224) not responding to ping, killing it. Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: Child (13224) not responding to ping, killing it. Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: Child (13224) not responding to ping, killing it. Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: Child (13224) died signal=3 Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: Child cleanup complete Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: child (13288) Started I'm not expecting a solution here but any help just to decode what each line is doing would be very instructive. Many thanks!

  Read the article

• Percona-server time out on /etc/init.d/mysql start

  - by geekmenot

  Every time I start mysql, using /etc/init.d/mysql start or service mysql start, it always times out. * Starting MySQL (Percona Server) database server mysqld [fail] However, I can get into mysql. Just wanted to know if there is a problem with the install because it happens all the time, not a one off error. mysql-error.log shows: 121214 11:25:56 mysqld_safe Starting mysqld daemon with databases from /data/mysql/ 121214 11:25:56 [Note] Plugin 'FEDERATED' is disabled. 121214 11:25:56 InnoDB: The InnoDB memory heap is disabled 121214 11:25:56 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121214 11:25:56 InnoDB: Compressed tables use zlib 1.2.3 121214 11:25:56 InnoDB: Using Linux native AIO 121214 11:25:56 InnoDB: Initializing buffer pool, size = 14.0G 121214 11:25:58 InnoDB: Completed initialization of buffer pool 121214 11:26:01 InnoDB: Waiting for the background threads to start 121214 11:26:02 Percona XtraDB (http://www.percona.com) 1.1.8-rel29.2 started; log sequence number 9333955393950 121214 11:26:02 [Note] Server hostname (bind-address): '0.0.0.0'; port: 3306 121214 11:26:02 [Note] - '0.0.0.0' resolves to '0.0.0.0'; 121214 11:26:02 [Note] Server socket created on IP: '0.0.0.0'. 121214 11:26:02 [Note] Slave SQL thread initialized, starting replication in log 'mysql-bin.005163' at position 624540946, relay log '/data/mysql/mysql-relay-bin.000043' position: 624541092 121214 11:26:02 [Note] Slave I/O thread: connected to master '[email protected]:3306',replication started in log 'mysql-bin.005180' at position 823447620 121214 11:26:02 [Note] Event Scheduler: Loaded 0 events 121214 11:26:02 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.5.28-29.2-log' socket: '/data/mysql/mysql.sock' port: 3306 Percona Server (GPL), Release 29.2

  Read the article

• Single m0n0wall - Two LAN Subnets - How To Setup

  - by SnAzBaZ

  I have two LAN subnets that I need to link together they are 192.168.4.0/24 and 192.168.5.0/24 There is a m0n0wall running on 192.168.4.1. It's LAN connection goes out to our network switch, and it's WAN port goes out to our ADSL modem. WAN is connected via PPPoE. The 192.168.4.0 subnet contains all of our office workstations. The 192.168.5.0 subnet contains development servers and test machines that need to obtain internet access and be "managed" by computers on the 192.168.4.0 subnet, but need to be on their own subnet as well. I have a Draytek 2820N configured on 192.168.5.1 with it's WAN2 port configured as 192.168.4.25 and a default gateway of 192.168.4.1. Machines on the 5.0 subnet can connect to the internet via the m0n0wall just fine. I configured a static route on the m0n0wall LAN interface, Network 192.168.5.0/24 and Gateway 192.168.4.25. Machines on the 5.0 subnet can ping machines on the 4.0 network but the reverse does not work. I configured a new firewall rule on the m0n0wall that allows any traffic on the LAN interface with a source IP of 192.168.4.25 to be allowed. The DrayTek firewall is currently configured to pass all traffic regardless. When I try to ping a machine in the 5.0 subnet from 4.0 I see this in my m0n0wall log: BLOCK 14:45:27.888157 LAN 192.168.4.25 192.168.4.37, type echoreply/0 ICMP So the reply is being sent from the 5.0 subnet but is not being allowed to reach my workstation because the firewall is blocking it. Why is the firewall blocking it ? I hope the explanation of my network is clear, please ask if you require further clarification. Thank you.

  Read the article

• web.config file changings guide

  - by Student

  Hi experts how are you all? i am student, and learning asp.net c# visual studio 2010 with using sql server 2005. I have developed a website which has database. I developed this website with self studies taking help from internet. the website is completed and working perfectly in my computer. I have hosting server and domain name registered already. the problem is when I upload my website it doesn't work there the following error displays: Server Error in '/' Application. Configuration Error Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately. Parser Error Message: Unrecognized attribute 'targetFramework'. Note that attribute names are case-sensitive. Source Error: Line 11: <system.web> Line 12: <customErrors mode="Off" /> Line 13: <compilation debug="false" targetFramework="4.0"/> Line 14: </system.web> Line 15: </configuration> Source File: C:\Inetpub\vhosts\urdureport.com\httpdocs\web.config Line: 13 Version Information: Microsoft .NET Framework Version:2.0.50727.5472; ASP.NET Version:2.0.50727.5474 I don't know what should I do to get it work on hosting server please help me in this regard that what should I do with this. Thank you in advance

  Read the article

• Freebsd jail for an small company - checklist - what shouldn't forget

  - by cajwine

  Looking for an checklist for an "small company freebsd/jail server". Having pretty common starting point: FreeBSD jail (remote/headless) for the company: public web, email, ftp server, and private (maybe in the future partially public) wiki (foswiki) 4 physical persons, (6 email addresses) + one admin - others will never use ssh) have already done usual hardening on the host side (like pf, sshguard etc). my major components are: dovecot, exim, apache22, proftpd, perl5.14. Looking for an checklist, what I shouldn't forget. My plan: openssl self-signed certificates for exim, dovecot and proftpd (wildcard keys) openssl self-signed certificate for apache (later will go for "trusted-signed" key) My questions are: is is an "good practice" having one pair of wildcard SSL-certificates for many programs? (exim, dovecot, proftpd) - or should I generate one key for each service? should I add all 4 persons as standard (unix) users, or I should go with virtual users? Asking because: have only small count of users, and it is more simple to configure everything (exim, dovecot) for local users ($HOME/Maildir), plus ability to set $HOME/.forward/vacation and etc. is here some (special) things what I should consider? (e.g. maybe, in the future we want setup our own webmail - will make this any difference?) any other recommendation? Thank you, hoping that this question fit into the http://serverfault.com/faq under the: Server and Business Workstation operating systems, hardware, software Operations, maintenance, and monitoring Looking for an checklist, but please explain why you're recommending it. See Good Subjective, Bad Subjective. related: What's your suggested mail server configuration for a FreeBSD server?

  Read the article

• File permission woes on an Ubuntu ec2 instance

  - by Pardoner

  I've set up an amazon ec2 instance and I'm have some file permission issues. I've created myself a new user and added myself to the following groups: adm:x:4:me,ubuntu sudo:x:27:me www-data:x:33:me,www-data ssh:x:108:me admin:x:111:me ubuntu:x:1000:www-data,me me:x:1001:me but when I cd /var/www I can't do simple commands without doing sudo. So I chown -R www-data:www-data /var/www to ensure that I'm in the owning group but I still have to type sudo for everything. If I sudo su www-data it works fine. Since I'm in the www-data group shouldn't I have the same privilages as www-data? One strange thing I'm noticing is that when I ls -l it list the owner but not the group names. Could this possibly be part of the issue? Is is posible for a directory to not be part of a group? drwxr-xr-x 4 www-data 4.0K Oct 24 16:39 . drwxr-xr-x 14 root 4.0K Oct 10 16:58 .. drwxrwxr-x 9 www-data 4.0K Oct 23 04:03 admin.mywebsite.com drwxrwxr-x 2 www-data 4.0K Oct 4 00:29 mywebsite.com drwxrwxr-x 9 www-data 4.0K Oct 23 04:03 staging.mywebsite.com Edit : It appears I had some alias messing with my ls command. By calling \ls -l I can see that all my files are in the correct group.

  Read the article

• Backup Exec tape rotation guidelines

  - by HannesFostie

  Hi We use Backup Exec to take care of our backups for our data server, exchange server, and one more set of systems. Each of these 3 is being done on a separate "set" of tapes. Our goal is to be able to roll back a full 2 weeks, with 1 full backup each weekend and differential/incremental backups in between (the difference between the two in our case isn't very big, because the employees mostly use a very similar set of files throughout the week). While playing around with the settings on how to achieve this, we set the time for BE to keep the full backup to 14 days, but because we have too much data this would require manual intervention each time to erase a certain tape and use that. What I would like to know is what kind of guidelines, tricks, tips and general "stuff to think about" you keep in mind when designing your backup schedule. The type of backups (full/diff/incr) isn't of that much importance in our case as it's more or less set in stone. Made this community wiki as it's not a very specific question. Thanks in advance!

  Read the article

• mysql thread count

  - by Ryan M.

  We have a web application that uses apache and mysql. Generally (according to Munin) our MySQL thread count sits between 2 and 4 at all times. The other day, our server almost came to a halt. HTTP requests were slow or wouldn't go through at all, SSH would work, but would take 30+ seconds to register keystrokes, etc.. So we pull up Munin and the only thing that's out of normal boundaries is the Mysql thread count. CPU usage was under 1%, load was under 1.0, plenty of available RAM. As mentioned before, the thread count floats around 2 to 4. At the time of our slow downs it had spiked to 14. So I start poking around the Internet and I see that in most cases, you'll start to see a higher thread count when you start running into slow queries. If I understand it correctly, the request comes in that takes a while to process, in the mean time other requests are coming in, so a new thread will be created to work on the request (yes?). But at the time of the slow down, we had 0 slow queries. My question is: What else can cause mysql to create additional threads. And would this sudden spike in threads possibly cause the server to slow down? To fix the issue, we restarted apache and everything went back to it's beautiful, normal self. Considering the the Server Vitals (CPU, RAM, Network, etc) were all ideal, and the thread count was the only thing out of place, this seems like the most logical thing to pursue as the possible cause. If it matters, we're on Mysql 5.1.40. Server is FreeBSD 7.2 and the server in question is inside a jail.

  Read the article

• Under what conditions will sendmail try to immediately resend a message instead of waiting for the standard requeue interval?

  - by Mike B

  CentOS 5.8 | Sendmail 8.14.4 I used to think that if SendMail experienced a temporary (400-class) error during delivery, it would place the message in a deferred queue (e.g. /var/spool/mqueue) and retry an hour later. For the most part, that appears to be the case. But every now and then, I'll notice log entries like this (email/domains renamed to protect the innocent :-) ) : Dec 5 01:43:03 foobox-out sendmail [11078]: qBE3l7js123022: to=<[email protected]>, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=124588, relay=exbox.foo.com. [10.10.10.10], dsn=4.0.0, stat=Deferred: 421 4.3.2 The maximum number of concurrent connections has exceeded a limit, closing transmission channel Dec 5 01:53:34 foobox-out sendmail [12763]: qBE3l7js123022: to=<[email protected]>, delay=00:10:31, xdelay=00:00:00, mailer=relay, pri=214588, relay=exbox.foo.com., dsn=4.0.0, stat=Deferred: 452 4.3.1 Insufficient system resources Dec 5 02:53:35 foobox-out sendmail [23255]: qBE3l7js123022: to=<[email protected]>, delay=01:10:32, xdelay=00:00:01, mailer=relay, pri=304588, relay=exbox.foo.com. [10.10.10.10], dsn=2.0.0, stat=Sent (<[email protected]> Queued mail for delivery) Why did Sendmail try again just 10 minutes after the first attempt and then wait another hour before trying again? If this is expected behavior, what scenarios will cause this faster requeue interval to occur?

  Read the article

< Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >