Search Results

Search found 10706 results on 429 pages for 'pkg config'.

Page 146/429 | < Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >

• Is there a better way to do bonded vlan tagged interfaces with XEN

  - by AJ01

  We have a number of XEN servers all running CentOS or RHEL. The VM's that they run are all required to be on their own VLAN for no other reason than the customer expects them to be. Long story short however, I can't change this right now. We are also required to have bonding enabled on the interfaces. So to accommodat this we enslave eth1 and eth2 to bond0. We then create a seperate interface called bond0.VLANID where VLANID corresponds to the correct vlan; eg ifcfg-bond0.204 DEVICE=bond0.204 BOOTPROTO=static ONBOOT=yes VLAN=yes BRIDGE=xenvlan204 Bridge to XEN As you will see, we eventually have to bridge this out to XEN, and we do this by adding another interface called xenvlan204 (in this instance) which contains; ifcfg-xenvlan204 DEVICE=xenvlan204 BOOTPROTO=none ONBOOT=yes TYPE=bridge XEN Vm Config Finally in our XEN config for each VM, we add vif = [ "bridge=xenvlan204" ] This then allows the vm host to access that particular vlan The Problem We've noticed a few problems with this setup. One being that we currently create the interfaces manually. Which means if we add more vlan enabled interfaces and bridges we usually have to restart xend which is something I'm not so hot about. Also lower level staff have their heads melted by the number of interfaces and the risk of a mistake occurring is high. Secondly, it can take sometime for a host to come up if it has a number of vlan taged interfaces. Thirdly, its just not scaling well on the management aspects The Question Is there a better more flexible way to do this (in particular with Xen that ships with centos 5.3, 5.4 and 5.5 as we have to support all three) that leverages either scripting or other solutions to allow an arbitrary amount of interfaces to be created when a vm is instanced. Your advise and expertise is more that welcomed.

  Read the article

• Load balancing with puppet

  - by Gonçalo Queirós

  Hi there. Im trying to setup a loadbalancing system. My load balancer (nginx) has a conf file where i should list all IP's of the upstream servers. I could put the IP's on the conf manually, but this ways i would need to change the conf file every time i add/remove an upstream server. For now i came up with two different ideas, but i don't like much of neither: 1 - Have every upstream machine to use Exported Resources to create a file with it's IP..Then the load balancer server will have an "include conf_directory/*", and load all the files created by the upstrem servers. Since the load balancer is using nginx this can be done, but if i wan't latter on to configure something that doesn't have the "include" on the conf files, this solution will not work. 2 - If the config doesn't support the "include" command, then we could have again, every upstream server use the Exported Resources to create a filw with its IP, and latter on, the load balancer execute a command that would pick every file and generate the config Both versions addopt the same techinque, the difference is that version 2 is used when the server (that needs to have a conf generated) doesn't recognize a command like "include" inside its own conf. Now, my question is, is there any way to do this in a different form? I suspect that there is, since puppet is made to manage multiple servers, it seems a bit strange not have a easy way to configure load balancers.

  Read the article

• "one-off" use of http_proxy in a Chef remote_file resource

  - by user169200

  I have a use case where most of my remote_file resources and yum resources download files directly from an internal server. However, there is a need to download one or two files with remote_file that is outside our firewall and which must go through a HTTP proxy. If I set the http_proxy setting in /etc/chef/client.rb, it adversely affects the recipe's ability to download yum and other files from internal resources. Is there a way to have a remote_file resource download a remote URL through a proxy without setting the http_proxy value in /etc/chef/client.rb? In my sample code, below, I'm downloading a redmine bundle from rubyforge.org, which requires my servers to go through a corporate proxy. I came up with a ruby_block before and after the remote_file resource that sets the http_proxy and "unsets" it. I'm looking for a cleaner way to do this. ruby_block "setenv-http_proxy" do block do Chef::Config.http_proxy = node['redmine']['http_proxy'] ENV['http_proxy'] = node['redmine']['http_proxy'] ENV['HTTP_PROXY'] = node['redmine']['http_proxy'] end action node['redmine']['rubyforge_use_proxy'] ? :create : :nothing notifies :create_if_missing, "remote_file[redmine-bundle.zip]", :immediately end remote_file "redmine-bundle.zip" do path "#{Dir.tmpdir}/redmine-#{attrs['version']}-bundle.zip" source attrs['download_url'] mode "0644" action :create_if_missing notifies :decompress, "zipp[redmine-bundle.zip]", :immediately notifies :create, "ruby_block[unsetenv-http_proxy]", :immediately end ruby_block "unsetenv-http_proxy" do block do Chef::Config.http_proxy = nil ENV['http_proxy'] = nil ENV['HTTP_PROXY'] = nil end action node['redmine']['rubyforge_use_proxy'] ? :create : :nothing end

  Read the article

• After few days of server running fine with nginx it start throwing 499 and 502

  - by Abhay Kumar

  Nginx start throwing 499 and 502 after running fine for few days, website is a rails app using thin as the webserver. Restarting the Nginx doent not seem to help. Below the the Nginx config Nginx config under sites-enabled upstream domain1 { least_conn; server 127.0.0.1:3009; server 127.0.0.1:3010; server 127.0.0.1:3011; } server { listen 80; # default_server; server_name xyz.com *.xyz.com; client_max_body_size 5M; access_log /home/ubuntu/www/xyz/current/log/access.log; root /home/ubuntu/www/xyz/current/public/; index index.html; location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_read_timeout 150; if (!-f $request_filename) { proxy_pass http://domain1; break; } } }

  Read the article

• Nginx configuration leads to endless redirect loop

  - by brianthecoder

  So I've looked at every sample configuration I could find and yet every time I try and view a page that requires ssl, I end up in an redirect loop. I'm running nginx/0.8.53 and passenger 3.0.2. Here's the ssl config server { listen 443 default ssl; server_name <redacted>.com www.<redacted>.com; root /home/app/<redacted>/public; passenger_enabled on; rails_env production; ssl_certificate /home/app/ssl/<redacted>.com.pem; ssl_certificate_key /home/app/ssl/<redacted>.key; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header X-Url-Scheme $scheme; proxy_redirect off; proxy_max_temp_file_size 0; location /blog { rewrite ^/blog(/.*)?$ http://blog.<redacted>.com/$1 permanent; } location ~* \.(js|css|jpg|jpeg|gif|png)$ { if (-f $request_filename) { expires max; break; } } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } Here's the non-ssl config server { listen 80; server_name <redacted>.com www.<redacted>.com; root /home/app/<redacted>/public; passenger_enabled on; rails_env production; location /blog { rewrite ^/blog(/.*)?$ http://blog.<redacted>.com/$1 permanent; } location ~* \.(js|css|jpg|jpeg|gif|png)$ { if (-f $request_filename) { expires max; break; } } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } Let me know if there's any additional info I can give to help diagnose the issue.

  Read the article

• apt-mirror does not mirror the i18n directory

  - by Fred

  I need to setup a local Ubuntu mirror so the whole network doesn't need to hit remote servers in order to update and install new packages. Following a brief tutorial found here, I managed to get a server up and running that correctly mirrors packages from the main and restricted categories. However, when I call apt-get update on a client, I get a couple of errors such as : Ign http://192.168.1.18 karmic/main Translation-fr Ign http://192.168.1.18 karmic/restricted Translation-fr Checking back on the server, I see that apt-mirror only took the binary-amd64 directory of the mirror, and didn't take i18n that would provide Translation-fr. The manpage for apt-mirror doesn't say anything about i18n, and Google is of no help either. How do I properly mirror i18n? My current mirror.list file is as follows : ############# config ################## # # set base_path /var/spool/apt-mirror # # if you change the base path you must create the directories below with write privileges # # set mirror_path $base_path/mirror # set skel_path $base_path/skel # set var_path $base_path/var # set cleanscript $var_path/clean.sh # set defaultarch <running host architecture> # set postmirror_script $var_path/postmirror.sh set run_postmirror 0 set nthreads 20 set _tilde 0 # ############# end config ############## deb http://mirror.cc.columbia.edu/pub/linux/ubuntu/archive karmic main restricted deb http://mirror.cc.columbia.edu/pub/linux/ubuntu/archive karmic-updates main restricted clean http://mirror.cc.columbia.edu/pub/linux/ubuntu/archive

  Read the article

• Defining Virtual and Real User Directories with Dovecot & Postfix

  - by blankabout

  Following a wobble described in this question we now have virtual and real users authenticating with Dovecot, the problem now is that the real users (who have been on the system for years) can no longer access their mail. I'm guessing that it is because Dovecot is configured to point to the virtual mailboxes but not the real mail boxes. These are snippets from the config files: /etc/dovecot/dovecot.conf !include conf.d/*.conf /etc/dovecot/conf.d/10-auth.cong passdb { driver = passwd-file # Path for passwd-file. Also set the default password scheme. args = scheme=cram-md5 /etc/cram-md5.pwd } userdb { driver=static #args = mail_uid=dovecot mail_gid=dovecot /etc/dovecot/userdb args = uid=vmail gid=vmail home=/var/spool/vhosts/%d/%n /etc/dovecot/userdb } [email protected]:::::/var/spool/vhosts/virtualdomain.com/:/bin/false:: We think the problem is that the Dovecot file 10-auth.conf does not contain a method of accessing the mailboxes for the real users. We have looked around on this site, dovecot.org and done the usual googling but cannot find anywhere that describes how to set up virtual users on alongside legacy real users. Any help would be appreciated, especially by our real users who would like the contents of their inboxes to be available! If any further config is required, please let me know.

  Read the article

• Unable to mount root fs over NFS [on hold]

  - by johnmadrak

  I am attempting to set up a Raspberry Pi running Pidora to boot from an NFS share. My configuration in cmdline.txt is: dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/nfs nfsroot=<serverip>:/fake/path,nfsvers=3,rw,nolock nfsrootdebug ip=dhcp elevator=deadline rootwait On the Pi, the output I see is: IP-Config: Got DHCP answer from <router>, my address is <clientip> IP-Config: Complete: device=eth0, hwaddr=<macaddress>, ipaddr=<clientip>, mask=255.255.255.0, gw=<routerip> host=<clientip>, domain=, nis-domain=(none) bootserver=<routerip>, rootserver=<serverip>, rootpath= nameserver0=<routerip> (It pauses for a bit here) VFS: Unable to mount root fs via NFS, trying floppy VFS: Cannot open root device "nfs" or unknown-block(2,0); error -6 Please append a correct "root=" boot option; here are the available partitions: ..... On the NFS Server (an OpenVZ Container), the output I see in the /var/log/messages is: Aug 22 23:24:01 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:783 for /fake/path (/fake/path) Aug 22 23:24:38 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:741 for /fake/path (/fake/path) Aug 22 23:25:25 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:752 for /fake/path (/fake/path) Aug 22 23:26:12 vps-4178 rpc.mountd[928]: authenticated mount request from <clientip>:876 for /fake/path (/fake/path) To test, I've made sure I can mount (non-root) from both the Pi and another machine and it worked. Does anyone have an idea on what could be wrong or how to narrow it down? Thank you in advanced for your help.

  Read the article

• Problems forwarding port 3306 on iptables with CentOS

  - by BoDiE2003

  Im trying to add a forward to the mysql server at 200.58.126.52 to allow the access from 200.58.125.39, and Im using the following rules (its my whole iptables of the VPS of my hosting). I can connect locally at the server that holds the mysql service as localhost, but not from outside. Can someone check if the following rules are fine? Thank you # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d 224.0.0.251 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp -s 200.58.125.39 --dport 3306 -j ACCEPT -A INPUT -p tcp -s 200.58.125.39 --sport 1024:65535 -d localhost --dport 3306 -m state --state NEW,ESTABLISHED -j ACCEPT -A OUTPUT -p tcp -s localhost --sport 3306 -d 200.58.125.39 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT COMMIT And this is the output of the connection trial. [root@qwhosti /home/qwhosti/public_html/admin/config] # mysql -u user_db -p -h 200.58.126.52 Enter password: ERROR 2003 (HY000): Can't connect to MySQL server on '200.58.126.52' (113)

  Read the article

• Nginx order of servers

  - by scrat

  I have 3 sites on my server. All are running on gunicorn and use unix sockets to communicate with nginx which routes requests. I got three records in nginx.conf like: server { listen 80; server_name site1.com; location / { proxy_pass http://unix:/tmp/site1.sock; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } For site1, site2, site3. If they are ordered as config for site1 goes first, and then goes config for site2 and site3 everything works good. But when I change the order for example to site2, site1, site3, then site1 becomes routed to site2. What am I doing wrong? Full server nginx.conf before servers configs: user www-data; worker_processes 4; pid /var/run/nginx.pid; events { worker_connections 768; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; include /etc/nginx/mime.types; default_type application/octet-stream; ## # Logging Settings ## access_log /var/log/nginx/access.log; error_log /var/log/nginx/error.log; ## # Gzip Settings ## gzip on; gzip_types text/css application/x-javascript text/x-component text/richtext image/svg+xml text/plain text/xsd text/xsl text/xml image/x-icon;

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• IIS 7, FastCGI, PHP and custom php.ini files

  - by Marlon

  I'm running PHP 5.3, FastCGI, and IIS 7 on Windows Server 2008. I have a site which I would like to configure its own php.ini settings for but things aren't working as expected. I am following the tutorial located here. This is what I have done so far: 1) Configured a new website with it's own AppPool. 2) Selected PHP 5.3.6 from the PHP Manager available on the website home on IIS (not the web server home which sets the global version of PHP) 3) Added the following lines to the section of the applicationHost.config file located at system32/inetsrv/config <application fullPath="C:\Program Files (x86)\PHP\v5.3\php-cgi.exe" arguments="-d open_basedir=C:\inetpub\wwwroot\kickasswebsite.com" maxInstances="4" idleTimeout="300" activityTimeout="30" requestTimeout="90" instanceMaxRequests="200" protocol="NamedPipe" queueLength="1000" flushNamedPipe="false" rapidFailsPerMinute="10"> <environmentVariables> <environmentVariable name="PHPRC" value="c:\inetpub\wwwroot\kickasswebsite.com" /> </environmentVariables> </application> 4) I then create a php.ini file located in C:\inetpub\wwwroot\kickasswebsite.com (the location of the root of the website) register_globals = on 5) I then run test.php which simply outputs everything the method call to phpinfo() returns. At this point, I observe that the global setting for register_globals = off (as it should be), but the local setting for register_globals = off, even though I specified it differently in the php.ini file I created at the root of the site. Furthermore, I see these settings in the output of the php.ini Configuration File (php.ini) Path C:\Windows Loaded Configuration File C:\Program Files (x86)\PHP\v5.3\php.ini Scan this dir for additional .ini files (none) Additional .ini files parsed (none) What am I messing up on, or is there a different way to go about this?

  Read the article

• Mount EC2 instance via SSH on Mac OS X

  - by darkporter

  OK I just can't figure this out. I have an EC2 instance, which I'm able to SSH into just fine with: ssh -i XXXX.pem [email protected] I can even make it slick from the command line by creating a ~/.ssh/config with this in it: Host XXXX HostName XXXX User ubuntu IdentityFile ~/.ec2/XXXX.pem Which allows me to simple do a ssh XXXX with no -i option. Now, I want to mount this via SSH. I've tried MacFuse/SSHFS, MacFusion and ExpandDrive, but no luck. It's supposed to "just work" but the SSH-related command line utilities and the Keychain Access program in OS X is confusing and opaque to me. From what I've read, these GUI programs don't care about .ssh/config, they care about the Keychain. Somehow I can associate my domain name I'm connecting to with a particular "identity" private key file (.pem file) but I have no idea how. I tried this: ssh-add -K XXXX.pem Which does add to the Keychain but it's not associated to a particular domain. These GUI mounting programs I mentioned all just spin and do nothing when I try to connect passwordless. No keychain prompt, no nothing. I've pretty much given up and I'm thinking about just setting up an SMB server, but I'd rather just go over SSH since I believe it's possible.

  Read the article

• "could not find suitable fingerprints matched to available hardware" error

  - by Alex

  I have a thinkpad t61 with a UPEK fingerprint reader. I'm running ubuntu 9.10, with fprint installed. Everything works fine (I am able to swipe my fingerprint to authenticate any permission dialogues or "sudo" prompts successfully) except for actually logging onto my laptop when I boot up or end my session. I receive an error below the gnome login that says "Could not locate any suitable fingerprints matched to available hardware." What is causing this? here are the contents of /etc/pam.d/common-auth file # # /etc/pam.d/common-auth - authentication settings common to all services # # This file is included from other service-specific PAM config files, # and should contain a list of the authentication modules that define # the central authentication scheme for use on the system # (e.g., /etc/shadow, LDAP, Kerberos, etc.). The default is to use the # traditional Unix authentication mechanisms. # # As of pam 1.0.1-6, this file is managed by pam-auth-update by default. # To take advantage of this, it is recommended that you configure any # local modules either before or after the default block, and use # pam-auth-update to manage selection of other modules. See # pam-auth-update(8) for details. # here are the per-package modules (the "Primary" block) auth sufficient pam_fprint.so auth [success=1 default=ignore] pam_unix.so nullok_secure # here's the fallback if no module succeeds auth requisite pam_deny.so # prime the stack with a positive return value if there isn't one already; # this avoids us returning an error just because nothing sets a success code # since the modules above will each just jump around auth required pam_permit.so # and here are more per-package modules (the "Additional" block) auth optional pam_ecryptfs.so unwrap # end of pam-auth-update config #auth sufficient pam_fprint.so #auth required pam_unix.so nullok_secure

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  Hiya, I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• Ubuntu and Windows and Separate HDs, oh my!

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. Here's a pic of the error I get when I try to boot to Windows: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu. (Someone suggested just reinstalling windows from installation CD. Agree?)

  Read the article

• nginx doesn't find the directory but apache does

  - by Jack Spairow

  I use apache as the backend server and nginx on the frontend. Apache listens to port 8080 and nginx to port 80. What I do is have the root point to the public folder foreach virtualhost: <VirtualHost *:8080> ServerAdmin webmaster@localhost ServerName site.com ServerAlias site.com *.site.com DocumentRoot /var/www/site.com/public <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/site.com/public/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> </VirtualHost> And here's the nginx config: server { listen 80; access_log /var/log/nginx.access.log; error_log /var/log/nginx.error.log; root /var/www/site.com/public; index index.php index.html; server_name site.com *.site.com; location / { location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $host; proxy_pass http://127.0.0.1:8080; proxy_cache one; proxy_cache_use_stale error timeout invalid_header updating; proxy_cache_key $scheme$host$request_uri; proxy_cache_valid 200 301 302 20m; proxy_cache_valid 404 1m; proxy_cache_valid any 15m; } } location ~ /\.(ht|git) { deny all; } } The problem is Apache resolves the domain just fine (site.com:8080), but nginx shows instead a 502 Bad Gateway (site.com:80). I tried looking at the error_log and access_log but I can't find any hint for why can't nginx work. EDIT: The problem was I wasn't able to include that isolated config for nginx.

  Read the article

• Accessing clearcase view drive from virtual machine is slow

  - by PermanentGuest

  I have a windows XP virtual machine running under a Windows XP host. On the host : On the host clearcase 7.1.1.2 is installed. I have a dynamic view mapped onto some drive. The view has certain VOB/directory structure where my application DLLs from the nightly build and config files are stored. I run my application on the host machine which uses the DLLs and config files from the VOB and everything runs smooth. Now I want to move this set-up to a virtual machine. On the guest : I'm running the guest with a vm-player. I don't want to install clear-case on this as I don't want to expose this machine onto the network. The network setting in the guest is 'host-only'. I have mapped the host's clearcase view drive as a shared folder and I'm able to access this drive from the virtual machine. Also, the application is running. However, the problem is that the access of the clearcase drive from the virtual machine is very slow. I can experience this from the windows explorer. Due to this, the starting of my application takes several seconds in the virtual machine while on the guest it comes up pretty fast. My question is : Is there any way to speed up the performance? I have managed to copy some of the DLLs which don't change frequently to the virtual machine to improve the performance. However, there are still lot of DLLs which have to be taken from the clearcase drive as they change frequently. VMplayer version is : VM Player 3.0.1 build-227600 Both guest and host is : Windows XP service pack 3 Host clearcase is : clearcase 7.1.1.2

  Read the article

• Nginx + WordPress + HHVM: Why isn't Batcache working? Would Varnish help even more?

  - by javipas

  I've heard great things about HHVM, so I've setup a copy of WordPress blog (on another domain) with Nginx (with the Pagespeed module) and HHVM. Right now the benefits are obvious: on the same config, load times are between two and three times faster. I'm trying to speed up things a little bit, and I've also installed Memcached and Batcache. I've installed the memcached package, copied object-cache.php (Pastebin) onto the root folder of the WordPress blog, and after that I've installed the Batcache plugin and copied the advanced-cache.php (Pastebin) file onto the wp-content folder. Also, I've included the line define('WP_CACHE', true); in the wp-config.php file. It seems it doesn't work, though. If I quickly reload the page several times Batcache should show the cached page, but it doesn't. It's easy to check that by reloading (Cmd+R on Chrome on OS X) the page several times and then viewing the page's code. Under the <head> section I should see some batcache stats, but they aren't there. I wonder if someone could give me some hint on this. On a side note, I don't know if I could add some other component in order to help the performance be even better. I'm thing about Varnish, but I'm not sure if it's just useless and it's just another way to the same I'm currently doing. Any other component there? (I'll test CDN for images, minifying js, etc and some other tricks as well, but I'm talking from the server perspective).

  Read the article

• C# sends SQL data 4 times less from one box than from another

  - by Bobb

  W2003, .NET 3.5, SQL 2008 I have prod and UAT app servers deployed in 2 different data centres. I have a C# app which reads text file, parse the text and sends the data to the SQL in bulk. SQL server is in US and the app servers are in London (but in different places). All POPs have dedicated network connections. There is no public internet involved. When the app runs on UAT server I can see in Perfmon that the Send byte/sec is x4 higher than from production server. My estimate is that one server outputs at 1 MB/s and the other at 250 KB/s rate. My suspicion immediately is that there is a router on one of the DCs which shapes traffic or does QoS limitation on traffice from London to US. However support and Windows team and networkig team all are saying that there are no differences in neither networking config on the 2 DCs nor NIC config on the 2 app server... How to find out why is the networking bottlneck is 4 times tighter in one place than in the other? What can I do about it?

  Read the article

• Linux boot - stop the kernel switching to a new framebuffer mode clearing output

  - by Avio

  I'm working on an embedded system (based onUbuntu 12.04 LTS) and I'm customizing its kernel. I'm having some problem with upstart, mountall and plymouth. Nothing unsolvable I suppose, but the real problem is that I can't diagnose properly what's going on because the kernel (or maybe plymouth) changes the video mode in the middle of the boot process. This completely wipes entire lines of log and prevents any debugging of kernel misconfigurations. My Grub2 config seems to be ok with: GRUB_CMDLINE_LINUX="" GRUB_CMDLINE_LINUX_DEFAULT="acpi=force noplymouth" GRUB_GFXMODE=1024x768x32 GRUB_GFXPAYLOAD_LINUX=keep Here is some relevant output of lspci: 00:00.0 Host bridge: Intel Corporation Mobile 945GSE Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GSE Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) And here is the relevant portion of my kernel configuration: CONFIG_AGP=y CONFIG_AGP_INTEL=y CONFIG_VGA_ARB=y CONFIG_VGA_ARB_MAX_GPUS=16 CONFIG_DRM=y CONFIG_DRM_KMS_HELPER=y CONFIG_DRM_I915=y CONFIG_DRM_I915_KMS=y CONFIG_VIDEO_OUTPUT_CONTROL=y CONFIG_FB=y CONFIG_FB_BOOT_VESA_SUPPORT=y CONFIG_FB_CFB_FILLRECT=y CONFIG_FB_CFB_COPYAREA=y CONFIG_FB_CFB_IMAGEBLIT=y CONFIG_FB_MODE_HELPERS=y CONFIG_FB_VESA=y CONFIG_BACKLIGHT_LCD_SUPPORT=y CONFIG_BACKLIGHT_CLASS_DEVICE=y CONFIG_VGA_CONSOLE=y CONFIG_VGACON_SOFT_SCROLLBACK=y CONFIG_VGACON_SOFT_SCROLLBACK_SIZE=640 CONFIG_DUMMY_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE=y CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y CONFIG_FONT_8x8=y CONFIG_FONT_8x16=y CONFIG_LOGO=y CONFIG_LOGO_LINUX_MONO=y CONFIG_LOGO_LINUX_VGA16=y CONFIG_LOGO_LINUX_CLUT224=y Every other custom/stock kernel boot fine with that Grub2 config. What I would like to have is a single flow of messages on a single console (retaining one screen resolution) from the bootup logo till the login prompt. Does anybody know what I have to tweak to achieve this?

  Read the article

• use ssh tunnel with phpmyadmin

  - by JohnMerlino

  I been using ssh tunnel to bypass firewall of remote mysql server. On my Ubuntu 12.04 installation, it works via the terminal and it works when using a program called mysql workbench. However, that program freezes often and I want to try phpmyadmin as an alternative. However, I cannot connect to remote server using ssh tunnel on phpmyadmin, albeit I can connect locally. These are the steps I've tried: 1) Open a tunnel, listening on localhost:3307 and forwarding everything to xxx.xxx.xxx.xxx:3306 (used 3307 because MySQL on my local machine uses the default port 3306): ssh -L 3307:localhost:3306 [email protected] So now I have the port for tunnel open and I have my local mysql installation default port: $ netstat -tln Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:3307 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN ... 2) Now I can easily connect to remote server via localhost using the terminal: $ mysql -u user.name -p -h 127.0.0.1 -P 3307 Notice that I expicitly identify 3307 as the port, so traffic forwards to the remote server, and hence it logs me in to the remote server. Unfortunately, the localhost/phpmyadmin local login interface doesn't allow you to specify a port option. So I modify the config-db.php file and change the $dbport variable to 3307, under the impression that the phpmyadmin interface will now work with port 3307: $ sudo vim /etc/phpmyadmin/config-db.php $dbport='3307'; Then I restart the mysql server. Unfortunately, it didn't work. When I use the remote credentials to login, it gives me error: #1045 Cannot log in to the MySQL server

  Read the article

• Share one ssl certificate between multiples vhost

  - by Cesar

  I have a setup like this: <VirtualHost 192.168.1.104:80> ServerName domain1 DocumentRoot /home/domain/public_html ... </VirtualHost> <VirtualHost 192.168.1.104:80> ServerName domain2 DocumentRoot /home/domain2/public_html ... </VirtualHost> <VirtualHost 192.168.1.104:80> DocumentRoot /home/domain3/public_html ServerName domain3 ... </VirtualHost> <VirtualHost 192.168.1.104:443> ServerName domain3 SSLCertificateFile /usr/share/ssl/certs/certificate.crt SSLCertificateKeyFile /usr/share/ssl/private/private.key SSLCACertificateFile /usr/share/ssl/certs/bundle.cabundle ... </VirtualHost> I want to use domain3 certificate in the other domains, preferably without having to repeat all the <VirtualHost 192.168.1.104:443> config. In other words I want something like this: If the vhost has no explicit ssl config use cert for domain3 (/usr/share/ssl/certs/certificate.crt) Notes: 1.- I for sure will be setting more vhosts in the future 2.- I know (and don't care) of the ssl warnings the browser will show (hostname mismatch) If this possible? how?

  Read the article

• Help with Ubuntu and Windows, separate HDs

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. I have some pictures of boot up: first one is strange error i get after messing with CMOS to finally get ubuntu install to work. http://imgur.com/5sqJa then boot menu: http://imgur.com/TWtLq then error: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu.

  Read the article

• Nginx configuration leads to endless redirect loop

  - by brianthecoder

  So I've looked at every sample configuration I could find and yet every time I try and view a page that requires ssl, I end up in an redirect loop. I'm running nginx/0.8.53 and passenger 3.0.2. Here's the ssl config server { listen 443 default ssl; server_name <redacted>.com www.<redacted>.com; root /home/app/<redacted>/public; passenger_enabled on; rails_env production; ssl_certificate /home/app/ssl/<redacted>.com.pem; ssl_certificate_key /home/app/ssl/<redacted>.key; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header X-Url-Scheme $scheme; proxy_redirect off; proxy_max_temp_file_size 0; location /blog { rewrite ^/blog(/.*)?$ http://blog.<redacted>.com/$1 permanent; } location ~* \.(js|css|jpg|jpeg|gif|png)$ { if (-f $request_filename) { expires max; break; } } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } Here's the non-ssl config server { listen 80; server_name <redacted>.com www.<redacted>.com; root /home/app/<redacted>/public; passenger_enabled on; rails_env production; location /blog { rewrite ^/blog(/.*)?$ http://blog.<redacted>.com/$1 permanent; } location ~* \.(js|css|jpg|jpeg|gif|png)$ { if (-f $request_filename) { expires max; break; } } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } Let me know if there's any additional info I can give to help diagnose the issue.

  Read the article

< Previous Page | 142 143 144 145 146 147 148 149 150 151 152 153  | Next Page >