Search Results

Search found 4049 results on 162 pages for 'serial communication'.

Page 147/162 | < Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >

• smartctl -t long isn't finishing

  - by xenoterracide

  I been running smartctl -t long on a drive for about 2 days now and it seems to be stalled at 10%. short and conveyance both passed. I have to send 1 of 2 drives purchased back I found badblocks with badblocks (none on this drive and I'ts made over a pass already). I'm just wondering if I should be concerned about this. smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD10EARS-00Y5B1 Serial Number: WD-WMAV51582123 Firmware Version: 80.00A80 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon May 10 22:19:52 2010 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 241) Self-test routine in progress... 10% of test remaining. Total time to complete Offline data collection: (20100) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 231) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 2 3 Spin_Up_Time 0x0027 131 131 021 Pre-fail Always - 6408 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 12 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 148 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 10 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 7 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 174 194 Temperature_Celsius 0x0022 106 102 000 Old_age Always - 41 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 99 - # 2 Extended offline Interrupted (host reset) 10% 30 - # 3 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

  Read the article

• How to structure game states in an entity/component-based system

  - by Eva

  I'm making a game designed with the entity-component paradigm that uses systems to communicate between components as explained here. I've reached the point in my development that I need to add game states (such as paused, playing, level start, round start, game over, etc.), but I'm not sure how to do it with my framework. I've looked at this code example on game states which everyone seems to reference, but I don't think it fits with my framework. It seems to have each state handling its own drawing and updating. My framework has a SystemManager that handles all the updating using systems. For example, here's my RenderingSystem class: public class RenderingSystem extends GameSystem { private GameView gameView_; /** * Constructor * Creates a new RenderingSystem. * @param gameManager The game manager. Used to get the game components. */ public RenderingSystem(GameManager gameManager) { super(gameManager); } /** * Method: registerGameView * Registers gameView into the RenderingSystem. * @param gameView The game view registered. */ public void registerGameView(GameView gameView) { gameView_ = gameView; } /** * Method: triggerRender * Adds a repaint call to the event queue for the dirty rectangle. */ public void triggerRender() { Rectangle dirtyRect = new Rectangle(); for (GameObject object : getRenderableObjects()) { GraphicsComponent graphicsComponent = object.getComponent(GraphicsComponent.class); dirtyRect.add(graphicsComponent.getDirtyRect()); } gameView_.repaint(dirtyRect); } /** * Method: renderGameView * Renders the game objects onto the game view. * @param g The graphics object that draws the game objects. */ public void renderGameView(Graphics g) { for (GameObject object : getRenderableObjects()) { GraphicsComponent graphicsComponent = object.getComponent(GraphicsComponent.class); if (!graphicsComponent.isVisible()) continue; GraphicsComponent.Shape shape = graphicsComponent.getShape(); BoundsComponent boundsComponent = object.getComponent(BoundsComponent.class); Rectangle bounds = boundsComponent.getBounds(); g.setColor(graphicsComponent.getColor()); if (shape == GraphicsComponent.Shape.RECTANGULAR) { g.fill3DRect(bounds.x, bounds.y, bounds.width, bounds.height, true); } else if (shape == GraphicsComponent.Shape.CIRCULAR) { g.fillOval(bounds.x, bounds.y, bounds.width, bounds.height); } } } /** * Method: getRenderableObjects * @return The renderable game objects. */ private HashSet<GameObject> getRenderableObjects() { return gameManager.getGameObjectManager().getRelevantObjects( getClass()); } } Also all the updating in my game is event-driven. I don't have a loop like theirs that simply updates everything at the same time. I like my framework because it makes it easy to add new GameObjects, but doesn't have the problems some component-based designs encounter when communicating between components. I would hate to chuck it just to get pause to work. Is there a way I can add game states to my game without removing the entity-component design? Does the game state example actually fit my framework, and I'm just missing something? EDIT: I might not have explained my framework well enough. My components are just data. If I was coding in C++, they'd probably be structs. Here's an example of one: public class BoundsComponent implements GameComponent { /** * The position of the game object. */ private Point pos_; /** * The size of the game object. */ private Dimension size_; /** * Constructor * Creates a new BoundsComponent for a game object with initial position * initialPos and initial size initialSize. The position and size combine * to make up the bounds. * @param initialPos The initial position of the game object. * @param initialSize The initial size of the game object. */ public BoundsComponent(Point initialPos, Dimension initialSize) { pos_ = initialPos; size_ = initialSize; } /** * Method: getBounds * @return The bounds of the game object. */ public Rectangle getBounds() { return new Rectangle(pos_, size_); } /** * Method: setPos * Sets the position of the game object to newPos. * @param newPos The value to which the position of the game object is * set. */ public void setPos(Point newPos) { pos_ = newPos; } } My components do not communicate with each other. Systems handle inter-component communication. My systems also do not communicate with each other. They have separate functionality and can easily be kept separate. The MovementSystem doesn't need to know what the RenderingSystem is rendering to move the game objects correctly; it just need to set the right values on the components, so that when the RenderingSystem renders the game objects, it has accurate data. The game state could not be a system, because it needs to interact with the systems rather than the components. It's not setting data; it's determining which functions need to be called. A GameStateComponent wouldn't make sense because all the game objects share one game state. Components are what make up objects and each one is different for each different object. For example, the game objects cannot have the same bounds. They can have overlapping bounds, but if they share a BoundsComponent, they're really the same object. Hopefully, this explanation makes my framework less confusing.

  Read the article

• What Counts For A DBA: Foresight

  - by drsql

  Of all the valuable attributes of a DBA covered so far in this series, ranging from passion to humility to practicality, perhaps one of the most important attributes may turn out to be the most seemingly-nebulous: foresight. According to Free Dictionary foresight is the "perception of the significance and nature of events before they have occurred". Foresight does not come naturally to most people, as the parent of any teenager will attest. No matter how clearly you see their problems coming they won't listen, and have to fail before eventually (hopefully) learning for themselves. Having graduated from the school of hard knocks, the DBA, the naive teenager no longer, acquires the ability to foretell how events will unfold in response to certain actions or attitudes with the unerring accuracy of a doom-laden prophet. Like Simba in the Lion King, after a few blows to the head, we foretell that a sore head that will be the inevitable consequence of a swing of Rafiki's stick, and we take evasive action. However, foresight is about more than simply learning when to duck. It's about taking the time to understand and prevent the habits that caused the stick to swing in the first place. And based on this definition, I often think there is a lot less foresight on display in my industry than there ought to be. Most DBAs reading this blog will spot a line such as the following in a piece of "working" code, understand immediately why it is less than optimimum, and take evasive action. …WHERE CAST (columnName as int) = 1 However, the programmers who regularly write this sort of code clearly lack that foresight, and this and numerous other examples of similarly-malodorous code prevail throughout our industry (and provide premium-grade fertilizer for the healthy growth of many a consultant's bank account). Sometimes, perhaps harried by impatient managers and painfully tight deadlines, everyone makes mistakes. Yes, I too occasionally write code that "works", but basically stinks. When the problems manifest, it is sometimes accompanied by a sense of grim recognition that somewhere in me existed the foresight to know that that approach would lead to this problem. However, in the headlong rush, warning signs got overlooked, lessons learned previously, which could supply the foresight to the current project, were lost and not applied.   Of course, the problem often is a simple lack of skills, training and knowledge in the relevant technology and/or business space; programmers and DBAs forced to do their best in the face of inadequate training, or to apply their skills in areas where they lack experience. However, often the problem goes deeper than this; I detect in some DBAs and programmers a certain laziness of attitude.   They veer from one project to the next, going with "whatever works", unwilling or unable to take the time to understand where their actions are leading them. Of course, the whole "Agile" mindset is often interpreted to favor flexibility and rapid production over aiming to get things right the first time. The faster you try to travel in the dark, frequently changing direction, the more important it is to have someone who has the foresight to know at least roughly where you are heading. This is doubly true for the data tier which, no matter how you try to deny it, simply cannot be "redone" every month as you learn aspects of the world you are trying to model that, with a little bit of foresight, you would have seen coming.   Sometimes, when as a DBA you can glance briefly at 200 lines of working SQL code and know instinctively why it will cause problems, foresight can feel like magic, but it isn't; it's more like muscle memory. It is acquired as the consequence of good experience, useful communication with those around you, and a willingness to learn continually, through continued education as well as from failure. Foresight can be deployed only by finding time to understand how the lessons learned from other DBAs, and other projects, can help steer the current project in the right direction.   C.S. Lewis once said "The future is something which everyone reaches at the rate of sixty minutes an hour, whatever he does, whoever he is." It cannot be avoided; the quality of what you build now is going to affect you, and others, at some point in the future. Take the time to acquire foresight; it is a love letter to your future self, to say you cared.

  Read the article

• Java EE at JavaOne - A Few Picks from a Very Rich Line-up

  - by Janice J. Heiss

  A rich and diverse set of sessions cast a spotlight on Java EE at this year’s JavaOne, ranging from the popular Web Framework Smackdown, to Java EE 6 and Spring, to sessions exploring Java EE 7, and one on the implications of HTML5. Some of the world’s best EE architects and developers will be sharing their insight and expertise. If only I could be at ten places at once!BOF4149 - Web Framework Smackdown 2012    Markus Eisele - Principal IT Architect, msg systems ag    Graeme Rocher - Senior Staff Engineer, VMware    James Ward - Developer Evangelist, Heroku    Ed Burns - Consulting Member of Technical Staff, Oracle    Santiago Pericasgeertsen - Software Engineer, Oracle* Monday, Oct 1, 8:30 PM - 9:15 PM - Parc 55 - Cyril Magnin II/III Much has changed since the first Web framework smackdown, at JavaOne 2005. Or has it? The 2012 edition of this popular panel discussion surveys the current landscape of Web UI frameworks for the Java platform. The 2005 edition featured JSF, Webwork, Struts, Tapestry, and Wicket. The 2012 edition features representatives of the current crop of frameworks, with a special emphasis on frameworks that leverage HTML5 and thin-server architecture. Java Champion Markus Eisele leads the lively discussion with panelists James Ward (Play), Graeme Rocher (Grails), Edward Burns (JSF) and Santiago Pericasgeertsen (Avatar).CON6430 - Java EE and Spring Framework Panel Discussion    Richard Hightower - Developer, InfoQ    Bert Ertman - Fellow, Luminis    Gordon Dickens - Technical Architect, IT101, Inc.    Chris Beams - Senior Technical Staff, VMware    Arun Gupta - Technology Evangelist, Oracle* Tuesday, Oct 2, 10:00 AM - 11:00 AM - Parc 55 - Cyril Magnin II/III In the age of Java EE 6 and Spring 3, enterprise Java developers have many architectural choices, including Java EE 6 and Spring, but which one is right for your project? Many of us have heard the debate and seen the flame wars—it’s a topic with passionate community members, and it’s a vibrant debate. If you are looking for some level-headed discussion, grounded in real experience, by developers who have tried both, then come join this discussion. InfoQ’s Java editors moderate the discussion, and they are joined by independent consultants and representatives from both Java EE and VMWare/SpringSource.BOF4213 - Meet the Java EE 7 Specification Leads   Linda Demichiel - Consulting Member of Technical Staff, Oracle   Bill Shannon - Architect, Oracle* Tuesday, Oct 2, 5:30 PM - 6:15 PM – Parc 55 - Cyril Magnin II/III This is your chance to meet face-to-face with the engineers who are developing the next version of the Java EE platform. In this session, the specification leads for the leading technologies that are part of the Java EE 7 platform discuss new and upcoming features and answer your questions. Come prepared with your questions, your feedback, and your suggestions for new features in Java EE 7 and beyond.CON10656 - JavaEE.Next(): Java EE 7, 8, and Beyond    Ian Robinson - IBM Distinguished Engineer, IBM    Mark Little - JBoss CTO, NA    Scott Ferguson - Developer, Caucho Technology    Cameron Purdy - VP Development, Oracle*Wednesday, Oct 3, 4:30 PM - 5:30 PM - Parc 55 - Cyril Magnin II/IIIIn this session, hear from a distinguished panel of industry and open source luminaries regarding where they believe the Java EE community is headed, starting with Java EE 7. The focus of Java EE 7 and 8 is mostly on the cloud, specifically aiming to bring platform as a service (PaaS) providers and application developers together so that portable applications can be deployed on any cloud infrastructure and reap all its benefits in terms of scalability, elasticity, multitenancy, and so on. Most importantly, Java EE will leverage the modularization work in the underlying Java SE platform. Java EE will, of course, also update itself for trends such as HTML5, caching, NoSQL, ployglot programming, map/reduce, JSON, REST, and improvements to existing core APIs.CON7001 - HTML5 WebSocket and Java    Danny Coward - Java, Oracle*Wednesday, Oct 3, 4:30 PM - 5:30 PM - Parc 55 - Cyril Magnin IThe family of HTML5 technologies has pushed the pendulum away from rich client technologies and toward ever-more-capable Web clients running on today’s browsers. In particular, WebSocket brings new opportunities for efficient peer-to-peer communication, providing the basis for a new generation of interactive and “live” Web applications. This session examines the efforts under way to support WebSocket in the Java programming model, from its base-level integration in the Java Servlet and Java EE containers to a new, easy-to-use API and toolset that are destined to become part of the standard Java platform.

  Read the article

• tile_static, tile_barrier, and tiled matrix multiplication with C++ AMP

  - by Daniel Moth

  We ended the previous post with a mechanical transformation of the C++ AMP matrix multiplication example to the tiled model and in the process introduced tiled_index and tiled_grid. This is part 2. tile_static memory You all know that in regular CPU code, static variables have the same value regardless of which thread accesses the static variable. This is in contrast with non-static local variables, where each thread has its own copy. Back to C++ AMP, the same rules apply and each thread has its own value for local variables in your lambda, whereas all threads see the same global memory, which is the data they have access to via the array and array_view. In addition, on an accelerator like the GPU, there is a programmable cache, a third kind of memory type if you'd like to think of it that way (some call it shared memory, others call it scratchpad memory). Variables stored in that memory share the same value for every thread in the same tile. So, when you use the tiled model, you can have variables where each thread in the same tile sees the same value for that variable, that threads from other tiles do not. The new storage class for local variables introduced for this purpose is called tile_static. You can only use tile_static in restrict(direct3d) functions, and only when explicitly using the tiled model. What this looks like in code should be no surprise, but here is a snippet to confirm your mental image, using a good old regular C array // each tile of threads has its own copy of locA, // shared among the threads of the tile tile_static float locA[16][16]; Note that tile_static variables are scoped and have the lifetime of the tile, and they cannot have constructors or destructors. tile_barrier In amp.h one of the types introduced is tile_barrier. You cannot construct this object yourself (although if you had one, you could use a copy constructor to create another one). So how do you get one of these? You get it, from a tiled_index object. Beyond the 4 properties returning index objects, tiled_index has another property, barrier, that returns a tile_barrier object. The tile_barrier class exposes a single member, the method wait. 15: // Given a tiled_index object named t_idx 16: t_idx.barrier.wait(); 17: // more code …in the code above, all threads in the tile will reach line 16 before a single one progresses to line 17. Note that all threads must be able to reach the barrier, i.e. if you had branchy code in such a way which meant that there is a chance that not all threads could reach line 16, then the code above would be illegal. Tiled Matrix Multiplication Example – part 2 So now that we added to our understanding the concepts of tile_static and tile_barrier, let me obfuscate rewrite the matrix multiplication code so that it takes advantage of tiling. Before you start reading this, I suggest you get a cup of your favorite non-alcoholic beverage to enjoy while you try to fully understand the code. 01: void MatrixMultiplyTiled(vector<float>& vC, const vector<float>& vA, const vector<float>& vB, int M, int N, int W) 02: { 03: static const int TS = 16; 04: array_view<const float,2> a(M, W, vA); 05: array_view<const float,2> b(W, N, vB); 06: array_view<writeonly<float>,2> c(M,N,vC); 07: parallel_for_each(c.grid.tile< TS, TS >(), 08: [=] (tiled_index< TS, TS> t_idx) restrict(direct3d) 09: { 10: int row = t_idx.local[0]; int col = t_idx.local[1]; 11: float sum = 0.0f; 12: for (int i = 0; i < W; i += TS) { 13: tile_static float locA[TS][TS], locB[TS][TS]; 14: locA[row][col] = a(t_idx.global[0], col + i); 15: locB[row][col] = b(row + i, t_idx.global[1]); 16: t_idx.barrier.wait(); 17: for (int k = 0; k < TS; k++) 18: sum += locA[row][k] * locB[k][col]; 19: t_idx.barrier.wait(); 20: } 21: c[t_idx.global] = sum; 22: }); 23: } Notice that all the code up to line 9 is the same as per the changes we made in part 1 of tiling introduction. If you squint, the body of the lambda itself preserves the original algorithm on lines 10, 11, and 17, 18, and 21. The difference being that those lines use new indexing and the tile_static arrays; the tile_static arrays are declared and initialized on the brand new lines 13-15. On those lines we copy from the global memory represented by the array_view objects (a and b), to the tile_static vanilla arrays (locA and locB) – we are copying enough to fit a tile. Because in the code that follows on line 18 we expect the data for this tile to be in the tile_static storage, we need to synchronize the threads within each tile with a barrier, which we do on line 16 (to avoid accessing uninitialized memory on line 18). We also need to synchronize the threads within a tile on line 19, again to avoid the race between lines 14, 15 (retrieving the next set of data for each tile and overwriting the previous set) and line 18 (not being done processing the previous set of data). Luckily, as part of the awesome C++ AMP debugger in Visual Studio there is an option that helps you find such races, but that is a story for another blog post another time. May I suggest reading the next section, and then coming back to re-read and walk through this code with pen and paper to really grok what is going on, if you haven't already? Cool. Why would I introduce this tiling complexity into my code? Funny you should ask that, I was just about to tell you. There is only one reason we tiled our extent, had to deal with finding a good tile size, ensure the number of threads we schedule are correctly divisible with the tile size, had to use a tiled_index instead of a normal index, and had to understand tile_barrier and to figure out where we need to use it, and double the size of our lambda in terms of lines of code: the reason is to be able to use tile_static memory. Why do we want to use tile_static memory? Because accessing tile_static memory is around 10 times faster than accessing the global memory on an accelerator like the GPU, e.g. in the code above, if you can get 150GB/second accessing data from the array_view a, you can get 1500GB/second accessing the tile_static array locA. And since by definition you are dealing with really large data sets, the savings really pay off. We have seen tiled implementations being twice as fast as their non-tiled counterparts. Now, some algorithms will not have performance benefits from tiling (and in fact may deteriorate), e.g. algorithms that require you to go only once to global memory will not benefit from tiling, since with tiling you already have to fetch the data once from global memory! Other algorithms may benefit, but you may decide that you are happy with your code being 150 times faster than the serial-version you had, and you do not need to invest to make it 250 times faster. Also algorithms with more than 3 dimensions, which C++ AMP supports in the non-tiled model, cannot be tiled. Also note that in future releases, we may invest in making the non-tiled model, which already uses tiling under the covers, go the extra step and use tile_static memory on your behalf, but it is obviously way to early to commit to anything like that, and we certainly don't do any of that today. Comments about this post by Daniel Moth welcome at the original blog.

  Read the article

• Real-world SignalR example, ditching ghetto long polling

  - by Jeff

  One of the highlights of BUILD last week was the announcement that SignalR, a framework for real-time client to server (or cloud, if you will) communication, would be a real supported thing now with the weight of Microsoft behind it. Love the open source flava! If you aren’t familiar with SignalR, watch this BUILD session with PM Damian Edwards and dev David Fowler. Go ahead, I’ll wait. You’ll be in a happy place within the first ten minutes. If you skip to the end, you’ll see that they plan to ship this as a real first version by the end of the year. Insert slow clap here. Writing a few lines of code to move around a box from one browser to the next is a way cool demo, but how about something real-world? When learning new things, I find it difficult to be abstract, and I like real stuff. So I thought about what was in my tool box and the decided to port my crappy long-polling “there are new posts” feature of POP Forums to use SignalR. A few versions back, I added a feature where a button would light up while you were pecking out a reply if someone else made a post in the interim. It kind of saves you from that awkward moment where someone else posts some snark before you. While I was proud of the feature, I hated the implementation. When you clicked the reply button, it started polling an MVC URL asking if the last post you had matched the last one the server, and it did it every second and a half until you either replied or the server told you there was a new post, at which point it would display that button. The code was not glam: // in the reply setup PopForums.replyInterval = setInterval("PopForums.pollForNewPosts(" + topicID + ")", 1500); // called from the reply setup and the handler that fetches more posts PopForums.pollForNewPosts = function (topicID) { $.ajax({ url: PopForums.areaPath + "/Forum/IsLastPostInTopic/" + topicID, type: "GET", dataType: "text", data: "lastPostID=" + PopForums.currentTopicState.lastVisiblePost, success: function (result) { var lastPostLoaded = result.toLowerCase() == "true"; if (lastPostLoaded) { $("#MorePostsBeforeReplyButton").css("visibility", "hidden"); } else { $("#MorePostsBeforeReplyButton").css("visibility", "visible"); clearInterval(PopForums.replyInterval); } }, error: function () { } }); }; What’s going on here is the creation of an interval timer to keep calling the server and bugging it about new posts, and setting the visibility of a button appropriately. It looks like this if you’re monitoring requests in FireBug: Gross. The SignalR approach was to call a message broker when a reply was made, and have that broker call back to the listening clients, via a SingalR hub, to let them know about the new post. It seemed weird at first, but the server-side hub’s only method is to add the caller to a group, so new post notifications only go to callers viewing the topic where a new post was made. Beyond that, it’s important to remember that the hub is also the means to calling methods at the client end. Starting at the server side, here’s the hub: using Microsoft.AspNet.SignalR.Hubs; namespace PopForums.Messaging { public class Topics : Hub { public void ListenTo(int topicID) { Groups.Add(Context.ConnectionId, topicID.ToString()); } } } Have I mentioned how awesomely not complicated this is? The hub acts as the channel between the server and the client, and you’ll see how JavaScript calls the above method in a moment. Next, the broker class and its associated interface: using Microsoft.AspNet.SignalR; using Topic = PopForums.Models.Topic; namespace PopForums.Messaging { public interface IBroker { void NotifyNewPosts(Topic topic, int lasPostID); } public class Broker : IBroker { public void NotifyNewPosts(Topic topic, int lasPostID) { var context = GlobalHost.ConnectionManager.GetHubContext<Topics>(); context.Clients.Group(topic.TopicID.ToString()).notifyNewPosts(lasPostID); } } } The NotifyNewPosts method uses the static GlobalHost.ConnectionManager.GetHubContext<Topics>() method to get a reference to the hub, and then makes a call to clients in the group matched by the topic ID. It’s calling the notifyNewPosts method on the client. The TopicService class, which handles the reply data from the MVC controller, has an instance of the broker new’d up by dependency injection, so it took literally one line of code in the reply action method to get things moving. _broker.NotifyNewPosts(topic, post.PostID); The JavaScript side of things wasn’t much harder. When you click the reply button (or quote button), the reply window opens up and fires up a connection to the hub: var hub = $.connection.topics; hub.client.notifyNewPosts = function (lastPostID) { PopForums.setReplyMorePosts(lastPostID); }; $.connection.hub.start().done(function () { hub.server.listenTo(topicID); }); The important part to look at here is the creation of the notifyNewPosts function. That’s the method that is called from the server in the Broker class above. Conversely, once the connection is done, the script calls the listenTo method on the server, letting it know that this particular connection is listening for new posts on this specific topic ID. This whole experiment enables a lot of ideas that would make the forum more Facebook-like, letting you know when stuff is going on around you.

  Read the article

• Closing the gap between strategy and execution with Oracle Business Intelligence 11g

  - by manan.goel(at)oracle.com

  Wikipedia defines strategy as a plan of action designed to achieve a particular goal. An example of this is General Electric's acquisitions and divestiture strategy (plan) designed to propel GE to number 1 or 2 place (goal) in every business segment that it operated in. Execution on the other hand can be defined as the actions taken to getting things done. In GE's case execution will be steps followed for mergers/acquisitions or divestiture. Business press has written extensively about the importance of both strategy and execution in achieving desired business objectives. Perhaps the quote from Thomas Edison says it best - "vision without execution is hallucination". Conversely, it can be said that "execution without vision" is well may be "wishful thinking". Research overwhelmingly point towards the wide gap between strategy and execution. According to a published study, 49% of surveyed executives perceive a gap between their organizations' ability to develop and communicate sound strategies and their ability to implement those strategies. Further, of these respondents, 64% don't have full confidence that their companies will be able to close the gap. Having established the severity and importance of the problem let's talk about the reasons for the strategy-execution gap. The common reasons include: -        Lack of clearly defined goals -        Lack of consistent measure of success -        Lack of ownership -        Lack of alignment -        Lack of communication -        Lack of proper execution -        Lack of monitoring       There are multiple approaches to solving the problem including organizational development practices, technology enablement etc. In most cases a combination of approaches is required to achieve the desired result. For the purposes of this discussion, I'll focus on technology.  Imagine an integrated closed loop technology platform that automates the entire management cycle from defining strategy to assigning ownership to communicating goals to achieving alignment to collaboration to taking actions to monitoring progress and achieving mid course corrections. Besides, for best ROI and lowest TCO such a system should also have characteristics like:  Complete -        Full functionality -        Rich end user access Open -        Any data source -        Any business application -        Any technology stack  Integrated -        Common metadata -        Common security -        Common system management From a capabilities perspective the system should provide the following capabilities: Define -        Strategy -        Objectives -        Ownership -        KPI's Communicate -        Pervasive -        Collaborative -        Role based -        Secure Execute -        Integrated -        Intuitive -        Secure -        Ubiquitous Monitor -        Multiple styles and formats -        Exception based -        Push & Pull Having talked about the business problem and outlined the blueprint for a technology solution, let's talk about how Oracle Business Intelligence 11g can help. Oracle Business Intelligence is a comprehensive business intelligence solution for reporting, ad hoc query and analysis, OLAP, dashboards and scorecards. Oracle's best in class BI platform is based on an architecturally integrated technology foundation that provides a unified end user experience and features a Common Enterprise Information Model, with common security, query request generation and optimization, and system management. The BI platform is ·         Complete - meaning it delivers all modes and styles of BI including reporting, ad hoc query and analysis, OLAP, dashboards and scorecards with a rich end user experience that includes visualization, collaboration, alerts and notifications, search and mobile access. ·         Open - meaning the BI platform integrates with any data source, ETL tool, business application, application server, security infrastructure, portal technology as well as any ODBC compliant third party analytical tool. The suite accesses data from multiple heterogeneous sources--including popular relational and multidimensional data sources and major ERP and CRM applications from Oracle and SAP. ·         Integrated - meaning the BI platform is based on an architecturally integrated technology foundation built on an open, standards based service oriented architecture.  The platform features a common enterprise information model, common security model and a common configuration, deployment and systems management framework. To summarize, Oracle Business Intelligence is a comprehensive, integrated BI platform that lets you define strategy, identify objectives, assign ownership, define KPI's, collaborate, take action, monitor, report and do course corrections all form a single interface and a single system. The platform's integrated metadata model and task based design ensures that the entire workflow from defining strategy to execution to monitoring is completely integrated delivering end to end visibility, transparency and agility. Click here to learn more about Oracle BI 11g. 

  Read the article

• dns server bind is not work

  - by milad

  I just installed bind on RHEL 6 and point a domain to that server. but actually when i ping domain it returns error 1214: Here is my named.conf: // // named.conf // // Provided by Red Hat bind package to configure the ISC BIND named(8) DNS // server as a caching only nameserver (as a localhost DNS resolver only). // // See /usr/share/doc/bind*/sample/ for example named configuration files. // options { listen-on port 53 { any; }; listen-on-v6 port 53 { ::1; }; directory "/var/named"; dump-file "/var/named/data/cache_dump.db"; statistics-file "/var/named/data/named_stats.txt"; memstatistics-file "/var/named/data/named_mem_stats.txt"; allow-query { any; }; recursion yes; dnssec-enable yes; dnssec-validation yes; dnssec-lookaside auto; /* Path to ISC DLV key */ bindkeys-file "/etc/named.iscdlv.key"; managed-keys-directory "/var/named/dynamic"; }; logging { channel default_debug { file "data/named.run"; severity dynamic; }; }; zone "." IN { type hint; file "named.ca"; }; include "/etc/named.rfc1912.zones"; include "/etc/named.root.key"; zone "mydomain.com"{ type master; file "/var/named/data/named.mydomain.com"; allow-update { none; }; };` AND The content of "/var/named/data/named.mydomain.com": $TTL 38400 mydomain.com. IN SOA ns1.mydomain.com. milad.yahoo.com. ( 2012101201 ; serial number YYMMDDNN 28800 ; Refresh 7200 ; Retry 864000 ; Expire 38400 ; Min TTL ) mydomain.com. IN A 1.2.3.4 www IN A 1.2.3.4 ns1.mydomain.com. IN A 1.2.3.4 ns2.mydomain.com. IN A 1.2.3.4 mydomain.com. IN NS ns1.mydomain.com. mydomain.com. IN NS ns2.mydomain.com. AND i'm sure the named service is running: [root@server ~]# service named status version: 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.3 CPUs found: 8 worker threads: 8 number of zones: 20 debug level: 0 xfers running: 0 xfers deferred: 0 soa queries in progress: 0 query logging is OFF recursive clients: 0/0/1000 tcp clients: 0/100 server is up and running named (pid 26299) is running... Thanks for your answers. i know that the ping is not the job of bind, i use it just to check whether domain is pointed to host or not.(ping is open in my server as i got reply in pinging ip) i use network-tools.com to ping domain. here the output of dig utility: dig mydomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.3 <<>> mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 6806 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;mydomain.com. IN A ;; Query time: 321 msec ;; SERVER: 5.6.7.8#53(5.6.7.8)##note that 5.6.7.8 is my idc dns ip ;; WHEN: Sun Oct 14 23:53:47 2012

  Read the article

• Customer Engagement: Are Your Customers Engaged With Your Brands?

  - by Michael Snow

  Engaging Customers is Critical for Business Growth This week we'll be spending some time looking at Customer Engagement. We all have stories about how we try to engage our customers better than ever before.  We all know that successfully engaging customers is critical to an organization’s business success. We also know that engaging our customers is more challenging today than ever before. There is so much noise to compete with for getting anyone's attention. Over the last decade and a half we’ve watched as the online channel became a primary one for conducting our business and even managing our lives. And during this whole process or evolution, the customer journey has grown increasingly complex. Customers themselves have assumed increasing power and influence over the purchase process and for setting the tone and pace of the relationships they have with brands and you see the evidence of this in the really high expectations that customers have today. They expect brand experiences that are personalized and relevant -- In other words they want experiences that demonstrate that the brand understands their interests, preferences and past interactions with them. They also expect their experience with a brand and the community surrounding it to be social and interactive – it’s no longer acceptable to have a static, one-way dialogue with your customer base or to fail to connect your customers with fellow customers, or with your employees and partners. And on top of all this, customers expect us to deliver this rich and engaging, personalized and interactive experience, in a consistent way across a variety of channels including web, mobile and social channels or even offline venues such as in-store or via a call center. And as a result, we see that delivery on these expectations and successfully engaging your customers is a great challenge today. Customers expect a personal, engaging and consistent online customer experience. Today’s consumer expects to engage with your brand and the community surrounding it in an interactive and social way. Customers have come to expect a lot for the online customer experience.  ·        They expect it to be personal: o   Accessible:  - Regardless of my device  Via my existing online identities  o   Relevant:  Content that interests me  o   Customized:  To be able to tailor my online experience  ·        They expect it to be engaging: o   Social:  So I can share content with my social networks  o   Intuitive:  To easily find what I need   o   Interactive:  So I can interact with online communities And they expect it to be consistent across the online experience – so you better have your brand and information ducks in a row. These expectations are not only limited to your customers by any means. Your employees (and partners) are also expecting to be empowered with engagement tools across their internal and external communications and interactions with customers, partners and other employees. We had a great conversation with Ted Schadler from Forrester Research entitled: "Mobile is the New Face of Engagement" that is now available On-Demand. Take a look at all the webcasts available to watch from our Social Business Thought Leader Series. Social capabilities have become so pervasive and changed customers’ expectations for their online experiences. The days of one-direction communication with customers are at an end. Today’s customers expect to engage in a dialogue with your brand and the community surrounding it in an interactive and social way. You have at a very short window of opportunity to engage a customer before they go to another site in their pursuit of information, product, or services. In fact, customers who engage with brands via social media tend to spend more that customers who don’t, between 20% and 40% more.  And your customers are also increasingly influenced by their social networks too – 40% of consumers say they factor in Facebook recommendations when making purchasing decisions.  This means a few different things for today’s businesses. Incorporating forms of social interaction such as commenting or reviews as well as tightly integrating your online experience with your customers’ social networking experiences into the online customer experience are crucial for maintaining the eyeballs on your desired pages. --- Notes/Sources: 93% - Cone Finds that Americans Expect Companies to Have a Presence in Social Media - http://www.coneinc.com/content1182 40% of consumers factor in Facebook recommendations when making decisions about purchasing (Increasing Campaign Effectiveness with Social Media, Syncapse, March 2011) 20%-40% - Customers who engage with a company via social media spend this percentage more with that company than other customers (Source: Bain & Company Report – Putting Social Media to Work)

  Read the article

• Process Centric Banking: Loan Origination Solution

  - by Manish Palaparthy

  There is an old proverb that goes, "The difference between theory and practice is greater in practice than in theory". So, we keep doing numerous "Proof of Concepts" with our own products on various business cases to analyze them deeply, understand and explain to our customers. We then present our learnings as they happened. The awareness of each PoC should help readers increase the trustworthiness of the results coming out of these PoCs. I present one such PoC where we invested a lot of time&effort.  Process Centric Banking : Loan Origination Solution Loan Origination is a process by which a borrower applies for a new loan and the lender processes that application. Loan origination includes the series of steps taken by the bank from the point the customer shows interest in a loan product all the way to disbursal of funds. The Loan Origination process is relevant for many kind of lenders in Financial services: Banks, Credit Unions, NBFCs(Non Banking Financial Companies) and so on. For simplicity sake, I will use "Bank" as the lending institution in the rest of my article.  Loan Origination is one of the core processes for Banks as it is the process by which the it creates assets against which the Institution earns most of its profits from. A well tuned loan origination process can affect the Bank in many positive ways. Banks have always shown great interest in automating the loan origination process for the above reason. However, due the constant changes in customer environment, market dynamics, prevailing economic conditions, cost pressures & regulatory environment they run into lot of challenges. Let me categorize some of these challenges for you Customer Environment Multiple Channels: Customer can use any of the available channels (Internet Banking, Email, Fax, Branch, Phone Banking, ATM, Broker, Mobile, Snail Mail) to perform all or some of the activities related to her Visibility into the origination process: Expect immediate update on the status of loan processing & alert messages Reduced Turn Around Time: Expect loans to be processed with least turn around time Reduced loan processing fees: Partly due to market dynamics the customer expects the loan processing fee to be negligible Market Dynamics Competitive environment:  The competition keeps creating many variants of loan products to attract customers, the bank needs to create similar product variants with better offers to attract customers or keep existing ones Ability to migrate loans from one vendor to another: It has become really easy for retail customers to move from one bank to the other given the low fee of loan processing and highly attractive offers. How does the bank protect it's customer base while actively engaging with potential customers banking with competitor banks Flexibility to react to market developments: Market development greatly influence loan processing, underwriting, asset valuation, risk mitigation rules. Can the bank modify rules and policies, the idea is not just to react to market developments but to pro-actively manage new developments Economic conditions Constant change in various rates and their implications on the rates and rules applied when on-boarding a loan: How quickly can the bank apply changes to rates offered to customers when the central bank changes various rates Requirements of Audit by the central banker: Tough economic conditions have demanded much more stringent audit rules and tests. The banks needs to produce ready reports(historic & operational) for audit compliance Risk Mitigation: While risk mitigation has always been a key concern for the bank, this is the area where the bank's underwriters & risk analysts spend the maximum time when processing a loan application. In order to reduce TAT the bank cannot compromise on its risk mitigation strategies Cost pressures Reduce Cost of processing per application: To deliver a reduced loan processing fee to the customer, the bank needs to keep its cost per processing loan application low. Meet customer TAT expectations while reducing the queues and the systems being used to process the loan application: The loan application could potentially be spending a lot of time waiting in the queue for further processing. Different volumes & patterns of applications demand different queuing algorithms. The bank needs to have real-time visibility into these queues and have the flexibility to change queuing algorithms at runtime  Increase the use of electronic communication and reduce the branch channel usage: Lesser automation leads not only leads to Increased turn around time, it also impacts more costs to reach out to customers The objective of our PoC was to implement a Loan Origination Solution whose ownership lies with the bank and effectively meet the challenges listed above. We built a simple story board for the solution We then went about implementing our storyboard using Oracle BPM Suite, Webcenter Content : Imaging. The web UI has been built on ADF technolgies, while the integration with core-services has been implemented using the underlying SOA infrastructure. The BPM process model is quite exhaustive can meet all the challenges listed above to reasonable degree. A bank intending to implement an end-to-end Loan Origination Solution has multiple options at it's disposal. It can Develop a customer Loan Origination Application from scratch: Gives maximum opportunity to build what you want but inflexible to upgrade and maintain. Higher TCO in long term Buy a Packaged application & customize it: Customizing a generic loan application can be tedious and prove as difficult as above. Build it using many disparate & un-integrated tools: Initially seems easier than developing from scratch. But, without integrated tool sets this is not a viable approach either or A solution based on a Framework: Independent Services and Business Process Modeling provide decoupled architecture that is flexible. We built this framework end-to-end with processes the core process of loan origination & several sub-processes such as Analyse and define customer needs, customer credit verification, identity check processes, legal review process, New customer registration & risk assessment.

  Read the article

• WebLogic JDBC Use of Oracle Wallet for SSL

  - by Steve Felts

  Introduction Secure Sockets Layer (SSL) can be used to secure the connection between the middle tier “client”, WebLogic Server (WLS) in this case, and the Oracle database server.  Data between WLS and database can be encrypted.  The server can be authenticated so you have proof that the database can be trusted by validating a certificate from the server.  The client can be authenticated so that the database only accepts connections from clients that it trusts. Similar to the discussion in an earlier article about using the Oracle wallet for database credentials, the Oracle wallet can also be used with SSL to store the keys and certificates.  By using it correctly, clear text passwords can be eliminated from the JDBC configuration and client/server configuration can be simplified by sharing the wallet across multiple datasources. There is a very good Oracle Technical White Paper on using SSL with the Oracle thin driver at http://www.oracle.com/technetwork/database/enterprise-edition/wp-oracle-jdbc-thin-ssl-130128.pdf [LINK1].  The link http://www.oracle.com/technetwork/middleware/weblogic/index-087556.html [LINK2] describes how to use WebLogic Server with Oracle JDBC Driver SSL. The information in this article is a guide on what steps need to be taken in the variety of available options; use the links above for details. SSL from the driver to the database server is basically turned on by specifying a protocol of “tcps” in the URL.  However, there is a fair amount of setup needed.  Also remember that there is an overhead in performance. Creating the wallets The common use cases are 1. “data encryption and server-only authentication”, requiring just a trust store, or 2. “data encryption and authentication of both tiers” (client and server), requiring a trust store and a key store. It is recommended to use the auto-login wallet type so that clear text passwords are not needed in the datasource configuration to open the wallet.  The store type for an auto-login wallet is “SSO” (Single Sign On), not “JKS” or “PKCS12” as in [LINK2].  The file name is “cwallet.sso”. Wallets are created using the orapki tool.  They need to be created based on the usage (encryption and/or authentication).  This is discussed in detail in [LINK1] in Appendix B or in the Advanced Security Administrator’s Guide of the Database documentation. Database Server Configuration It is necessary to update the sqlnet.ora and listener.ora files with the directory location of the wallet using WALLET_LOCATION.  These files also indicate whether or not SSL_CLIENT_AUTHENTICATION is being used (true or false). The Oracle Listener must also be configured to use the TCPS protocol.  The recommended port is 2484. LISTENER = (ADDRESS_LIST= (ADDRESS=(PROTOCOL=tcps)(HOST=servername)(PORT=2484))) WebLogic Server Classpath The WebLogic Server CLASSPATH must have three additional security files. The files that need to be added to the WLS CLASSPATH are $MW_HOME/modules/com.oracle.osdt_cert_1.0.0.0.jar $MW_HOME/modules/com.oracle.osdt_core_1.0.0.0.jar $MW_HOME/modules/com.oracle.oraclepki_1.0.0.0.jar One way to do this is to add them to PRE_CLASSPATH environment variable for use with the standard WebLogic scripts. Setting the Oracle Security Provider It’s necessary to enable the Oracle PKI provider on the client side.  This can either be done statically by updating the java.security file under the JRE or dynamically by setting it in a WLS startup class using java.security.Security.insertProviderAt(new oracle.security.pki.OraclePKIProvider (), 3); See the full example of the startup class in [LINK2]. Datasource Configuration When creating a WLS datasource, set the PROTOCOL in the URL to tcps as in the following. jdbc:oracle:thin:@(DESCRIPTION=(ADDRESS=(PROTOCOL=tcps)(HOST=host)(PORT=port))(CONNECT_DATA=(SERVICE_NAME=myservice))) For encryption and server authentication, use the datasource connection properties: - javax.net.ssl.trustStore=location of wallet file on the client - javax.net.ssl.trustStoreType=”SSO” For client authentication, use the datasource connection properties: - javax.net.ssl.keyStore=location of wallet file on the client - javax.net.ssl.keyStoreType=”SSO” Note that the driver connection properties for the wallet require a file name, not a directory name. Active GridLink ONS over SSL For completeness, there is another SSL usage for WLS datasources.  The communication with the Oracle Notification Service (ONS) for load balancing information and node up/down events can use SSL also. Create an auto-login wallet and use the wallet on the client and server.  The following is a sample sequence to create a test wallet for use with ONS. orapki wallet create -wallet ons -auto_login -pwd ONS_Wallet orapki wallet add -wallet ons -dn "CN=ons_test,C=US" -keysize 1024 -self_signed -validity 9999 -pwd ONS_Wallet orapki wallet export -wallet ons -dn "CN=ons_test,C=US" -cert ons/cert.txt -pwd ONS_Wallet On the database server side, it’s necessary to define the walletfile directory in the file $CRS_HOME/opmn/conf/ons.config and run onsctl stop/start. When configuring an Active GridLink datasource, the connection to the ONS must be defined.  In addition to the host and port, the wallet file directory must be specified.  By not giving a password, a SSO wallet is assumed. Summary To use SSL with the Oracle thin driver without any clear text passwords, use an SSO Oracle Wallet.  SSL support in the Oracle thin driver is available starting in 10g Release 2.

  Read the article

• Cloud to On-Premise Connectivity Patterns

  - by Rajesh Raheja

  Do you have a requirement to convert an Opportunity in Salesforce.com to an Order/Quote in Oracle E-Business Suite? Or maybe you want the creation of an Oracle RightNow Incident to trigger an on-premise Oracle E-Business Suite Service Request creation for RMA and Field Scheduling? If so, read on. In a previous blog post, I discussed integrating TO cloud applications, however the use cases above are the reverse i.e. receiving data FROM cloud applications (SaaS) TO on-premise applications/databases that sit behind a firewall. Oracle SOA Suite is assumed to be on-premise with with Oracle Service Bus as the mediation and virtualization layer. The main considerations for the patterns are are security i.e. shielding enterprise resources; and scalability i.e. minimizing firewall latency. Let me use an analogy to help visualize the patterns: the on-premise system is your home - with your most valuable possessions - and the SaaS app is your favorite on-line store which regularly ships (inbound calls) various types of parcels/items (message types/service operations). You need the items at home (on-premise) but want to safe guard against misguided elements of society (internet threats) who may masquerade as postal workers and vandalize property (denial of service?). Let's look at the patterns. Pattern: Pull from Cloud The on-premise system polls from the SaaS apps and picks up the message instead of having it delivered. This may be done using Oracle RightNow Object Query Language or SOAP APIs. This is particularly suited for certain integration approaches wherein messages are trickling in, can be centralized and batched e.g. retrieving event notifications on an hourly schedule from the Oracle Messaging Service. To compare this pattern with the home analogy, you are avoiding any deliveries to your home and instead go to the post office/UPS/Fedex store to pick up your parcel. Every time. Pros: On-premise assets not exposed to the Internet, firewall issues avoided by only initiating outbound connections Cons: Polling mechanisms may affect performance, may not satisfy near real-time requirements Pattern: Open Firewall Ports The on-premise system exposes the web services that needs to be invoked by the cloud application. This requires opening up firewall ports, routing calls to the appropriate internal services behind the firewall. Fusion Applications uses this pattern, and auto-provisions the services on the various virtual hosts to secure the topology. This works well for service integration, but may not suffice for large volume data integration. Using the home analogy, you have now decided to receive parcels instead of going to the post office every time. A door mail slot cut out allows the postman can drop small parcels, but there is still concern about cutting new holes for larger packages. Pros: optimal pattern for near real-time needs, simpler administration once the service is provisioned Cons: Needs firewall ports to be opened up for new services, may not suffice for batch integration requiring direct database access Pattern: Virtual Private Networking The on-premise network is "extended" to the cloud (or an intermediary on-demand / managed service offering) using Virtual Private Networking (VPN) so that messages are delivered to the on-premise system in a trusted channel. Using the home analogy, you entrust a set of keys with a neighbor or property manager who receives the packages, and then drops it inside your home. Pros: Individual firewall ports don't need to be opened, more suited for high scalability needs, can support large volume data integration, easier management of one connection vs a multitude of open ports Cons: VPN setup, specific hardware support, requires cloud provider to support virtual private computing Pattern: Reverse Proxy / API Gateway The on-premise system uses a reverse proxy "API gateway" software on the DMZ to receive messages. The reverse proxy can be implemented using various mechanisms e.g. Oracle API Gateway provides firewall and proxy services along with comprehensive security, auditing, throttling benefits. If a firewall already exists, then Oracle Service Bus or Oracle HTTP Server virtual hosts can provide reverse proxy implementations on the DMZ. Custom built implementations are also possible if specific functionality (such as message store-n-forward) is needed. In the home analogy, this pattern sits in between cutting mail slots and handing over keys. Instead, you install (and maintain) a mailbox in your home premises outside your door. The post office delivers the parcels in your mailbox, from where you can securely retrieve it. Pros: Very secure, very flexible Cons: Introduces a new software component, needs DMZ deployment and management Pattern: On-Premise Agent (Tunneling) A light weight "agent" software sits behind the firewall and initiates the communication with the cloud, thereby avoiding firewall issues. It then maintains a bi-directional connection either with pull or push based approaches using (or abusing, depending on your viewpoint) the HTTP protocol. Programming protocols such as Comet, WebSockets, HTTP CONNECT, HTTP SSH Tunneling etc. are possible implementation options. In the home analogy, a resident receives the parcel from the postal worker by opening the door, however you still take precautions with chain locks and package inspections. Pros: Light weight software, IT doesn't need to setup anything Cons: May bypass critical firewall checks e.g. virus scans, separate software download, proliferation of non-IT managed software Conclusion The patterns above are some of the most commonly encountered ones for cloud to on-premise integration. Selecting the right pattern for your project involves looking at your scalability needs, security restrictions, sync vs asynchronous implementation, near real-time vs batch expectations, cloud provider capabilities, budget, and more. In some cases, the basic "Pull from Cloud" may be acceptable, whereas in others, an extensive VPN topology may be well justified. For more details on the Oracle cloud integration strategy, download this white paper.

  Read the article

• Cloud to On-Premise Connectivity Patterns

  - by Rajesh Raheja

  Do you have a requirement to convert an Opportunity in Salesforce.com to an Order/Quote in Oracle E-Business Suite? Or maybe you want the creation of an Oracle RightNow Incident to trigger an on-premise Oracle E-Business Suite Service Request creation for RMA and Field Scheduling? If so, read on. In a previous blog post, I discussed integrating TO cloud applications, however the use cases above are the reverse i.e. receiving data FROM cloud applications (SaaS) TO on-premise applications/databases that sit behind a firewall. Oracle SOA Suite is assumed to be on-premise with with Oracle Service Bus as the mediation and virtualization layer. The main considerations for the patterns are are security i.e. shielding enterprise resources; and scalability i.e. minimizing firewall latency. Let me use an analogy to help visualize the patterns: the on-premise system is your home - with your most valuable possessions - and the SaaS app is your favorite on-line store which regularly ships (inbound calls) various types of parcels/items (message types/service operations). You need the items at home (on-premise) but want to safe guard against misguided elements of society (internet threats) who may masquerade as postal workers and vandalize property (denial of service?). Let's look at the patterns. Pattern: Pull from Cloud The on-premise system polls from the SaaS apps and picks up the message instead of having it delivered. This may be done using Oracle RightNow Object Query Language or SOAP APIs. This is particularly suited for certain integration approaches wherein messages are trickling in, can be centralized and batched e.g. retrieving event notifications on an hourly schedule from the Oracle Messaging Service. To compare this pattern with the home analogy, you are avoiding any deliveries to your home and instead go to the post office/UPS/Fedex store to pick up your parcel. Every time. Pros: On-premise assets not exposed to the Internet, firewall issues avoided by only initiating outbound connections Cons: Polling mechanisms may affect performance, may not satisfy near real-time requirements Pattern: Open Firewall Ports The on-premise system exposes the web services that needs to be invoked by the cloud application. This requires opening up firewall ports, routing calls to the appropriate internal services behind the firewall. Fusion Applications uses this pattern, and auto-provisions the services on the various virtual hosts to secure the topology. This works well for service integration, but may not suffice for large volume data integration. Using the home analogy, you have now decided to receive parcels instead of going to the post office every time. A door mail slot cut out allows the postman can drop small parcels, but there is still concern about cutting new holes for larger packages. Pros: optimal pattern for near real-time needs, simpler administration once the service is provisioned Cons: Needs firewall ports to be opened up for new services, may not suffice for batch integration requiring direct database access Pattern: Virtual Private Networking The on-premise network is "extended" to the cloud (or an intermediary on-demand / managed service offering) using Virtual Private Networking (VPN) so that messages are delivered to the on-premise system in a trusted channel. Using the home analogy, you entrust a set of keys with a neighbor or property manager who receives the packages, and then drops it inside your home. Pros: Individual firewall ports don't need to be opened, more suited for high scalability needs, can support large volume data integration, easier management of one connection vs a multitude of open ports Cons: VPN setup, specific hardware support, requires cloud provider to support virtual private computing Pattern: Reverse Proxy / API Gateway The on-premise system uses a reverse proxy "API gateway" software on the DMZ to receive messages. The reverse proxy can be implemented using various mechanisms e.g. Oracle API Gateway provides firewall and proxy services along with comprehensive security, auditing, throttling benefits. If a firewall already exists, then Oracle Service Bus or Oracle HTTP Server virtual hosts can provide reverse proxy implementations on the DMZ. Custom built implementations are also possible if specific functionality (such as message store-n-forward) is needed. In the home analogy, this pattern sits in between cutting mail slots and handing over keys. Instead, you install (and maintain) a mailbox in your home premises outside your door. The post office delivers the parcels in your mailbox, from where you can securely retrieve it. Pros: Very secure, very flexible Cons: Introduces a new software component, needs DMZ deployment and management Pattern: On-Premise Agent (Tunneling) A light weight "agent" software sits behind the firewall and initiates the communication with the cloud, thereby avoiding firewall issues. It then maintains a bi-directional connection either with pull or push based approaches using (or abusing, depending on your viewpoint) the HTTP protocol. Programming protocols such as Comet, WebSockets, HTTP CONNECT, HTTP SSH Tunneling etc. are possible implementation options. In the home analogy, a resident receives the parcel from the postal worker by opening the door, however you still take precautions with chain locks and package inspections. Pros: Light weight software, IT doesn't need to setup anything Cons: May bypass critical firewall checks e.g. virus scans, separate software download, proliferation of non-IT managed software Conclusion The patterns above are some of the most commonly encountered ones for cloud to on-premise integration. Selecting the right pattern for your project involves looking at your scalability needs, security restrictions, sync vs asynchronous implementation, near real-time vs batch expectations, cloud provider capabilities, budget, and more. In some cases, the basic "Pull from Cloud" may be acceptable, whereas in others, an extensive VPN topology may be well justified. For more details on the Oracle cloud integration strategy, download this white paper.

  Read the article

• hostapd running on Ubuntu Server 13.04 only allows single station to connect when using wpa

  - by user450688

  Problem Only a single station can connect to hostapd at a time. Any single station can connect (W8, OSX, iOS, Nexus) but when two or more hosts are connected at the same time the first client loses its connectivity. However there are no connectivity issues when WPA is not used. Setup Linux (Ubuntu server 13.04) wireless router (with separate networks for wired WAN, wired LAN, and Wireless LAN. iptables-save output: *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.0.0/24 -o p4p1 -j MASQUERADE -A POSTROUTING -s 10.0.1.0/24 -o p4p1 -j MASQUERADE COMMIT *mangle :PREROUTING ACCEPT [13:916] :INPUT ACCEPT [9:708] :FORWARD ACCEPT [4:208] :OUTPUT ACCEPT [9:3492] :POSTROUTING ACCEPT [13:3700] COMMIT *filter :INPUT DROP [0:0] :FORWARD DROP [0:0] :OUTPUT ACCEPT [9:3492] -A INPUT -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -i p4p1 -p tcp -m tcp --dport 22 -m state --state NEW -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i wlan0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A FORWARD -i p4p1 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -i eth0 -j ACCEPT -A FORWARD -i wlan0 -j ACCEPT -A FORWARD -i lo -j ACCEPT COMMIT /etc/hostapd/hostapd.conf #Wireless Interface interface=wlan0 driver=nl80211 ssid=<removed> hw_mode=g channel=6 max_num_sta=15 auth_algs=3 ieee80211n=1 wmm_enabled=1 wme_enabled=1 #Configure Hardware Capabilities of Interface ht_capab=[HT40+][SMPS-STATIC][GF][SHORT-GI-20][SHORT-GI-40][RX-STBC12] #Accept all MAC address macaddr_acl=0 #Shared Key Authentication wpa=1 wpa_passphrase=<removed> wpa_key_mgmt=WPA-PSK wpa_pairwise=CCMP rsn_pairwise=CCMP ###IPad Connectivevity Repair ieee8021x=0 eap_server=0 Wireless Card #lshw output product: RT2790 Wireless 802.11n 1T/2R PCIe vendor: Ralink corp. physical id: 0 bus info: pci@0000:03:00.0 logical name: mon.wlan0 version: 00 serial: <removed> width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=rt2800pci driverversion=3.8.0-25-generic firmware=0.34 ip=10.0.1.254 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn #iw list output Band 1: Capabilities: 0x272 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 2-streams Max AMSDU length: 3839 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-15, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (27.0 dBm) * 2417 MHz [2] (27.0 dBm) * 2422 MHz [3] (27.0 dBm) * 2427 MHz [4] (27.0 dBm) * 2432 MHz [5] (27.0 dBm) * 2437 MHz [6] (27.0 dBm) * 2442 MHz [7] (27.0 dBm) * 2447 MHz [8] (27.0 dBm) * 2452 MHz [9] (27.0 dBm) * 2457 MHz [10] (27.0 dBm) * 2462 MHz [11] (27.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ AP } <= 8, total <= 8, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * set_tx_bitrate_mask * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (84) * Unknown command (87) * Unknown command (85) * Unknown command (89) * Unknown command (92) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 * Unknown mode (10): 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types: * IBSS: 0x40 0xb0 0xc0 0xd0 * managed: 0x40 0xd0 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * mesh point: 0xb0 0xc0 0xd0 * P2P-client: 0x40 0xd0 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 * Unknown mode (10): 0x40 0xd0 Device supports RSN-IBSS. HT Capability overrides: * MCS: ff ff ff ff ff ff ff ff ff ff * maximum A-MSDU length * supported channel width * short GI for 40 MHz * max A-MPDU length exponent * min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS.

  Read the article

• How to set Grub to automatically load Xen kernel

  - by Cerin

  How do you configure Grub to automatically use the Xen kernel under Ubuntu 11.10? No matter what I do, it loads the first menuentry. The only way I can get it to load Xen is to manually select the kernel, which I can't do if I have to reboot the server remotely, or there's a power failure and the machine automatically boots up when power's restored, etc. It's driving me nuts. In my /boot/grub/grub.cfg, the Xen kernel is at index 4 (i.e. it's the 5th menuentry). So I've tried: Setting GRUB_DEFAULT=4, and running sudo update-grub Setting GRUB_DEFAULT=saved and GRUB_SAVEDEFAULT=true, and running sudo update-grub Setting GRUB_DEFAULT="Ubuntu GNU/Linux, with Xen 4.1-amd64 and Linux 3.0.0-16-server", and running sudo update-grub None of these work. It continues to load the first menuentry, which is "Ubuntu, with Linux 3.0.0-16-server". Below is my current /boot/grub/grub.cfg. What am I doing wrong? # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="Ubuntu GNU/Linux, with Xen 4.1-amd64 and Linux 3.0.0-16-server" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=2 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.0.0-16-server' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod gzio insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac linux /boot/vmlinuz-3.0.0-16-server root=UUID=d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac ro initrd /boot/initrd.img-3.0.0-16-server } menuentry 'Ubuntu, with Linux 3.0.0-16-server (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac echo 'Loading Linux 3.0.0-16-server ...' linux /boot/vmlinuz-3.0.0-16-server root=UUID=d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.0.0-16-server } submenu "Previous Linux versions" { menuentry 'Ubuntu, with Linux 3.0.0-12-server' --class ubuntu --class gnu-linux --class gnu --class os { recordfail set gfxpayload=$linux_gfx_mode insmod gzio insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac linux /boot/vmlinuz-3.0.0-12-server root=UUID=d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac ro initrd /boot/initrd.img-3.0.0-12-server } menuentry 'Ubuntu, with Linux 3.0.0-12-server (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac echo 'Loading Linux 3.0.0-12-server ...' linux /boot/vmlinuz-3.0.0-12-server root=UUID=d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.0.0-12-server } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### submenu "Xen 4.1-amd64" { menuentry 'Ubuntu GNU/Linux, with Xen 4.1-amd64 and Linux 3.0.0-16-server' --class ubuntu --class gnu-linux --class gnu --class os --class xen { insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac echo 'Loading Xen 4.1-amd64 ...' multiboot /boot/xen-4.1-amd64.gz placeholder echo 'Loading Linux 3.0.0-16-server ...' module /boot/vmlinuz-3.0.0-16-server placeholder root=UUID=d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac ro echo 'Loading initial ramdisk ...' module /boot/initrd.img-3.0.0-16-server } menuentry 'Ubuntu GNU/Linux, with Xen 4.1-amd64 and Linux 3.0.0-16-server (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os --class xen { insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac echo 'Loading Xen 4.1-amd64 ...' multiboot /boot/xen-4.1-amd64.gz placeholder echo 'Loading Linux 3.0.0-16-server ...' module /boot/vmlinuz-3.0.0-16-server placeholder root=UUID=d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac ro single echo 'Loading initial ramdisk ...' module /boot/initrd.img-3.0.0-16-server } menuentry 'Ubuntu GNU/Linux, with Xen 4.1-amd64 and Linux 3.0.0-12-server' --class ubuntu --class gnu-linux --class gnu --class os --class xen { insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac echo 'Loading Xen 4.1-amd64 ...' multiboot /boot/xen-4.1-amd64.gz placeholder echo 'Loading Linux 3.0.0-12-server ...' module /boot/vmlinuz-3.0.0-12-server placeholder root=UUID=d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac ro echo 'Loading initial ramdisk ...' module /boot/initrd.img-3.0.0-12-server } menuentry 'Ubuntu GNU/Linux, with Xen 4.1-amd64 and Linux 3.0.0-12-server (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os --class xen { insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac echo 'Loading Xen 4.1-amd64 ...' multiboot /boot/xen-4.1-amd64.gz placeholder echo 'Loading Linux 3.0.0-12-server ...' module /boot/vmlinuz-3.0.0-12-server placeholder root=UUID=d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac ro single echo 'Loading initial ramdisk ...' module /boot/initrd.img-3.0.0-12-server } } ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod raid insmod mdraid1x insmod part_msdos insmod part_msdos insmod ext2 set root='(mduuid/be73165bc31d6f5cd00d05036c7b964f)' search --no-floppy --fs-uuid --set=root d72bad3f-9ed7-44b9-b3d1-d7af9f62a8ac linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ###

  Read the article

• How to build a great relationship with your colleagues

  - by Maria Sandu

  Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-ascii- mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi- mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} When you start new job, you worry about your performance, about being able to do what the manager asks you to do, but you also worry about the relations with your colleagues. How will you get along with them? What if they don’t like you? Have you ever felt you’re „the new guy” and your colleagues have already their own way of talking one to each other, their own jokes? It’s a common feeling and can actually become stressful. I am Norbert, Middleware Presales Intern in Hungary and I’ve been working within Oracle for only 1 month. Joining such a big company has been a challenge from many perspectives. One of them was adapting with the environment and getting to know all my colleagues. You know it’s quite difficult to introduce yourself, to try to liaise with them and find some common topics, so I felt very lucky and comfortable when my manager introduced me to all of my colleagues. It was easier to accommodate and we basically we had a starting point for our discussions. We started to talk about what my position means, for how many years they’ve been within Oracle, other Oracle related topics, but also more personal stuff like what they do after work. Having this opportunity of talking with all of them helped me introduce myself in a proper way and actually I told them many things about myself. Networking wasn’t my best skill, but these first days were really helpful from a network point of view. What else can you do to get along with your colleagues? One second thing I consider as being really helpful in networking is asking work-related questions. For instance, when you don’t know how to do something or don’t understand it, asking one of your colleagues will also help you to make a connection with him and you could easily continue the discussion with some other topics which are more personal. It’s a very effective strategy and in a company like Oracle people are very willing to help you with your tasks and perform at a high level. If you see your colleagues going to lunch, you should join them. It will help you become part of their community, finding out what’s new in their lives, you’ll, step-by-step, take part in their conversations and be up to date with the hot topics they talk about. One other opportunity of becoming part of your colleagues’ community are the internal events. Subscribing to the local free time activities mailing list is very useful for finding out information about when they’re going out and have a drink or attending all sorts of events. For instance, this is how I’ve found out about a party within Oracle that most of the employees here attend. It’s a wonderful opportunity for chatting and make a stronger connection to some of them. How important is attending these events? Think about how much time you spend at work. You’d like to enjoy your work and the environment, so getting along with your colleagues is a nice thing to have. I recently attended a corporate party whose purpose was to facilitate the interaction and communication between employees. It was a real success and we had a lot of fun, especially because it was a costume party.  All the fancy dresses and funny clothes we wore made the atmosphere really enjoyable. It was easy to liaise with colleague with whom I had never interacted with before. There was a friendly spirit among us, chatting about personal stuff and about various pleasant things. Working in an international company is not an easy thing because you interact with many people and they have different styles, but all these opportunities of informal interaction are a good way to adapt to the new working environment.

  Read the article

• Design Pattern for Complex Data Modeling

  - by Aaron Hayman

  I'm developing a program that has a SQL database as a backing store. As a very broad description, the program itself allows a user to generate records in any number of user-defined tables and make connections between them. As for specs: Any record generated must be able to be connected to any other record in any other user table (excluding itself...the record, not the table). These "connections" are directional, and the list of connections a record has is user ordered. Moreover, a record must "know" of connections made from it to others as well as connections made to it from others. The connections are kind of the point of this program, so there is a strong possibility that the number of connections made is very high, especially if the user is using the software as intended. A record's field can also include aggregate information from it's connections (like obtaining average, sum, etc) that must be updated on change from another record it's connected to. To conserve memory, only relevant information must be loaded at any one time (can't load the entire database in memory at load and go from there). I cannot assume the backing store is local. Right now it is, but eventually this program will include syncing to a remote db. Neither the user tables, connections or records are known at design time as they are user generated. I've spent a lot of time trying to figure out how to design the backing store and the object model to best fit these specs. In my first design attempt on this, I had one object managing all a table's records and connections. I attempted this first because it kept the memory footprint smaller (records and connections were simple dicts), but maintaining aggregate and link information between tables became....onerous (ie...a huge spaghettified mess). Tracing dependencies using this method almost became impossible. Instead, I've settled on a distributed graph model where each record and connection is 'aware' of what's around it by managing it own data and connections to other records. Doing this increases my memory footprint but also let me create a faulting system so connections/records aren't loaded into memory until they're needed. It's also much easier to code: trace dependencies, eliminate cycling recursive updates, etc. My biggest problem is storing/loading the connections. I'm not happy with any of my current solutions/ideas so I wanted to ask and see if anybody else has any ideas of how this should be structured. Connections are fairly simple. They contain: fromRecordID, fromTableID, fromRecordOrder, toRecordID, toTableID, toRecordOrder. Here's what I've come up with so far: Store all the connections in one big table. If I do this, either I load all connections at once (one big db call) or make a call every time a user table is loaded. The big issue here: the size of the connections table has the potential to be huge, and I'm afraid it would slow things down. Store in separate tables all the outgoing connections for each user table. This is probably the worst idea I've had. Now my connections are 'spread out' over multiple tables (one for each user table), which means I have to make a separate DB called to each table (or make a huge join) just to find all the incoming connections for a particular user table. I've avoided making "one big ass table", but I'm not sure the cost is worth it. Store in separate tables all outgoing AND incoming connections for each user table (using a flag to distinguish between incoming vs outgoing). This is the idea I'm leaning towards, but it will essentially double the total DB storage for all the connections (as each connection will be stored in two tables). It also means I have to make sure connection information is kept in sync in both places. This is obviously not ideal but it does mean that when I load a user table, I only need to load one 'connection' table and have all the information I need. This also presents a separate problem, that of connection object creation. Since each user table has a list of all connections, there are two opportunities for a connection object to be made. However, connections objects (designed to facilitate communication between records) should only be created once. This means I'll have to devise a common caching/factory object to make sure only one connection object is made per connection. Does anybody have any ideas of a better way to do this? Once I've committed to a particular design pattern I'm pretty much stuck with it, so I want to make sure I've come up with the best one possible.

  Read the article

• Windows Phone 7 Review &ndash; Part 1: LG Quantum

  - by Nikita Polyakov

  As many of my fellow geeks, I ran out and got a retail windows Phone 7 on the first day. Just had to have it :) I’ve had the developer prototypes in my hands for previous 3 months on and off, so I finally wanted to have one I call my own. I’ve rushed the Launch   I’ve checked out both AT&T and T-Mobile offerings on day 1 and decided on a Samsung Focus. Great screen, super light and thin. If you don’t believe me that this phone can compete with the best of the non-Phone 7 offerings - get it in your hand to compare for yourself. I have to say that even though the on-screen keyboard on Windows Phone 7 is one of the best, the amount of text I write on my phone and my expectation of how long that takes for a short reply are very high. Also the phone being so slick and sexy did not feel solid or confident in my hand or pocket. As the dust settled   Arrives the LG Quantum – now on AT&T and worldwide. First impression of the softer plastic, the back battery cover is solid metal - the entire phone feels solid and indestructible! Phone fits just right in my hand, it’s almost too good. It does not feel like it will crack in your jeans. I feel safe holding it and don’t feel like if I or someone were to bump into me walking it’d fly out of my hand. I’ve dropped and had thrown the Focus a few times on accident as it’s weight is negligible. I won’t even dream of lying the first day adjusting to a 3.5’ LCD screen from the Samsung’s blistering bright and poppy AMOLED 4’ was hard. But the colors and sharpness are still very good. I find it almost easier on the eyes actually for day to day use.  I had a chance to lay the phone down in the line with the prototypes and final versions of other phones that had LCD screens – LG makes HTC looks like a budget LCD compared to a high end LCD in the home theatre department. I am consistently complemented by friends that have the HD7 or Surround on how much better my screen looks. The screen just looks like the most color correct phone out of the line up. Even next to Samsung it makes it look oversaturated, but can’t match the true blacks compensating with true white.   Day to Day Usability   What I also noticed that is a huge difference is how much I am not accidently hitting the soft keys at the bottom. I real pain on Focus since holding it in am average size hand already would accidently touch the controls at the bottom. QWERTY keyboard on this phone is great. It’s like the mission for LG is “make it solid!”. Keyboard has a very durable feel.   LG’s has a secret wild card though is the DLNA support. If you seen an ad for it, you should. Imagine this – playing a song from your phone straight to your network connected A/V receiver. Done. Pictures to TV. Done. Video. Done. DLNA works with components that advertise to as well as Windows 7, XBOX 360 and other consoles.  I will write an extensive review of that experience in near future. LG Exclusive apps – from panorama photo taker to voice to text translator and even look-n-type app that works like a backup inverse camera, there is quite a bit there that won’t be found on the other phones. I’ll review those in more detail in another segment. Conclusion So for a quick comparison: If you want a phone that is super thin, light and is core reference of a Windows Phone 7 – Samsung Focus it is. If you want a great phone with solid secure feel, real keyboard, media features - the hands down winner is LG Quantum.   You can pick up the LG Quantum at AT&T in US and worldwide as LG Optimus 7Q.   Final thought: I have not had SmartPhone that I felt was a reliable trusty primary communication device since Samsung BlackJack II, this time the LG got the crown.   [ Disclosure: Phone was provided to me free of charge. That has been the case for all of my phones for years, nothing new - I get them all. ]

  Read the article

• How Hacker Can Access VPS CentOS 6 content?

  - by user2118559

  Just want to understand. Please, correct mistakes and write advices Hacker can access to VPS: 1. Through (using) console terminal, for example, using PuTTY. To access, hacker need to know port number, username and password. Port number hacker can know scanning open ports and try to login. The only way to login as I understand need to know username and password. To block (make more difficult) port scanning, need to use iptables configure /etc/sysconfig/iptables. I followed this https://www.digitalocean.com/community/articles/how-to-setup-a-basic-ip-tables-configuration-on-centos-6 tutorial and got *nat :PREROUTING ACCEPT [87:4524] :POSTROUTING ACCEPT [77:4713] :OUTPUT ACCEPT [77:4713] COMMIT *mangle :PREROUTING ACCEPT [2358:200388] :INPUT ACCEPT [2358:200388] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [2638:477779] :POSTROUTING ACCEPT [2638:477779] COMMIT *filter :INPUT DROP [1:40] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [339:56132] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -p tcp -m tcp ! --tcp-flags FIN,SYN,RST,ACK SYN -m state --state NEW -j DROP -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG FIN,SYN,RST,PSH,ACK,URG -j DROP -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 110 -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m tcp --dport 21 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 21 -j ACCEPT COMMIT Regarding ports that need to be opened. If does not use ssl, then seems must leave open port 80 for website. Then for ssh (default 22) and for ftp (default 21). And set ip address, from which can connect. So if hacker uses other ip address, he can not access even knowing username and password? Regarding emails not sure. If I send email, using Gmail (Send mail as: (Use Gmail to send from your other email addresses)), then port 25 not necessary. For incoming emails at dynadot.com I use Email Forwarding. Does it mean that emails “does not arrive to VPS” (before arriving to VPS, emails are forwarded, for example to Gmail)? If emails does not arrive to VPS, then seems port 110 also not necessary. If use only ssl, must open port 443 and close port 80. Do not understand regarding port 3306 In PuTTY with /bin/netstat -lnp see Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 992/mysqld As understand it is for mysql. But does not remember that I have opened such port (may be when installed mysql, the port is opened automatically?). Mysql is installed on the same server, where all other content. Need to understand regarding port 3306 2. Also hacker may be able access console terminal through VPS hosting provider Control Panel (serial console emergency access). As understand only using console terminal (PuTTY, etc.) can make “global” changes (changes that can not modify with ftp). 3. Hacker can access to my VPS exploiting some hole in my php code and uploading, for example, Trojan. Unfortunately, faced situation that VPS was hacked. As understand it was because I used ZPanel. On VPS ( \etc\zpanel\panel\bin) ) found one php file, that was identified as Trojan by some virus scanners (at virustotal.com). Experimented with the file on local computer (wamp). And appears that hacker can see all content of VPS, rename, delete, upload etc. From my opinion, if in PuTTY use command like chattr +i /etc/php.ini then hacker could not be able to modify php.ini. Is there any other way to get into VPS?

  Read the article

• How do I turn on wireless adapter on HP Envy dv6 7200 under Ubuntu (any version)?

  - by Dave B.

  I have a new HP Envy dv6 7200 with dual boot Windows 8 / Ubuntu 12.04. In windows, the F12 key in Windows activates the "airplane mode" switch which enables/disables both on-board (mini PCIe) and USB wireless adapters. In Ubuntu, however, the wireless adapter is turned off by default and cannot be turned back on via the F12 key (or any other combination of F12 and Ctrl, Fn, Shift, etc.). Let me explain the "fixes" I've seen in various forums and explain what did or did not happen. These are listed in no particular order. (Spoiler alert: wireless is still broke). Solution 1? Use HP's "Wireless Assistant" utility to permanently activate the wireless card in Windows, then boot into Ubuntu to happily find it working. Unfortunately, this utility works in Windows 7 but not Windows 8. On the other hand, hardware drivers from HP are only available for Windows 8 for this model. Catch 22 (I could not find a comparable utility for Windows 8). Solution 2? Use a USB wireless adapter to sidestep the on-board device. I purchased such a device from thinkpenguin.com to be sure that it would be Linux-friendly. However, the wireless switch enables / disables all wireless devices including USB. So, there's my $50 donation to the nice folks at thinkpenguin.com, but still no solution. Solution 3? Following the Think Penguin folk's suggestion, modify the mini PCI express adapter following instructions here: http://www.notebookforums.com/t/225429/broken-wireless-hardware-switch-fix Tempting, but I then violate the terms of my warranty mere days after opening the box. This might be a good solution for an older machine that you want to get your geek on with, but not for a new box. Solution 4? rfkill unblock all No effect whatsoever. ubuntu@ubuntu-hp-evny:~$ rfkill unblock all ubuntu@ubuntu-hp-evny:~$ rfkill list all 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Solution 5? Re-install drivers. Done and done. Ubuntu recognizes the device - perhaps even without re-installing the drivers? - but cannot turn it on. How do I know this? In the Network Manager drop-down menu, the wireless option is blacked out and a message reads something like: "wireless network is disabled by a hardware switch". Solution 6? Identify a physical switch on the laptop and flip it. There is no such switch on this machine. In fact, walking through Best Buy yesterday, I checked and not a single new laptop PC had a physical switch on it. All of the wireless switches are either the F2 or F12 key ... I wonder if askubuntu will not be plagued by this exact issue in the near future? Additional info - lspci ubuntu@ubuntu-hp-evny:~$ lspci 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.2 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 3 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 08:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5229 (rev 01) 0a:00.0 Network controller: Ralink corp. Device 539b 0b:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Any suggestions would be much appreciated!

  Read the article

• ASP.NET: Using pickup directory for outgoing e-mails

  - by DigiMortal

  Sending e-mails out from web applications is very common task. When we are working on or test our systems with real e-mail addresses we don’t want recipients to receive e-mails (specially if we are using some subset of real data9. In this posting I will show you how to make ASP.NET SMTP client to write e-mails to disc instead of sending them out. SMTP settings for web application I have seen many times the code where all SMTP information is kept in app settings just to read them in code and give to SMTP client. It is not necessary because we can define all these settings under system.web => mailsettings node. If you are using web.config to keep SMTP settings then all you have to do in your code is just to create SmtpClient with empty constructor. var smtpClient = new SmtpClient(); Empty constructor means that all settings are read from web.config file. What is pickup directory? If you want drastically raise e-mail throughput of your SMTP server then it is not very wise plan to communicate with it using SMTP protocol. it adds only additional overhead to your network and SMTP server. Okay, clients make connections, send messages out and it is also overhead we can avoid. If clients write their e-mails to some folder that SMTP server can access then SMTP server has e-mail forwarding as only resource-eager task to do. File operations are way faster than communication over SMTP protocol. The directory where clients write their e-mails as files is called pickup directory. By example, Exchange server has support for pickup directories. And as there are applications with a lot of users who want e-mail notifications then .NET SMTP client supports writing e-mails to pickup directory instead of sending them out. How to configure ASP.NET SMTP to use pickup directory? Let’s say, it is more than easy. It is very easy. This is all you need. <system.net>   <mailSettings>     <smtp deliveryMethod="SpecifiedPickupDirectory">       <specifiedPickupDirectory pickupDirectoryLocation="c:\temp\maildrop\"/>     </smtp>   </mailSettings> </system.net> Now make sure you don’t miss come points: Pickup directory must physically exist because it is not created automatically. IIS (or Cassini) must have write permissions to pickup directory. Go through your code and look for hardcoded SMTP settings. Also take a look at all places in your code where you send out e-mails that there are not some custom settings used for SMTP! Also don’t forget that your mails will be written now to pickup directory and they are not sent out to recipients anymore. Advanced scenario: configuring SMTP client in code In some advanced scenarios you may need to support multiple SMTP servers. If configuration is dynamic or it is not kept in web.config you need to initialize your SmtpClient in code. This is all you need to do. var smtpClient = new SmtpClient(); smtpClient.DeliveryMethod = SmtpDeliveryMethod.SpecifiedPickupDirectory; smtpClient.PickupDirectoryLocation = pickupFolder; Easy, isn’t it? i like when advanced scenarios end up with simple and elegant solutions but not with rocket science. Note for IIS SMTP service SMTP service of IIS is also able to use pickup directory. If you have set up IIS with SMTP service you can configure your ASP.NET application to use IIS pickup folder. In this case you have to use the following setting for delivery method. SmtpDeliveryMethod.PickupDirectoryFromIis You can set this setting also in web.config file. <system.net>   <mailSettings>     <smtp deliveryMethod="PickupDirectoryFromIis" />   </mailSettings> </system.net> Conclusion Who was still using different methods to avoid sending e-mails out in development or testing environment can now remove all the bad code from application and live on mail settings of ASP.NET. It is easy to configure and you have less code to support e-mails when you use built-in e-mail features wisely.

  Read the article

• Windows for IoT, continued

  - by Valter Minute

  Originally posted on: http://geekswithblogs.net/WindowsEmbeddedCookbook/archive/2014/08/05/windows-for-iot-continued.aspxI received many interesting feedbacks on my previous blog post and I tried to find some time to do some additional tests. Bert Kleinschmidt pointed out that pins 2,3 and 10 of the Galileo are connected directly to the SOC, while pin 13, the one used for the sample sketch is controlled via an I2C I/O expander. I changed my code to use pin 2 instead of 13 (just changing the variable assignment at the beginning of the code) and latency was greatly reduced. Now each pulse lasts for 1.44ms, 44% more than the expected time, but ways better that the result we got using pin 13. I also used SetThreadPriority to increase the priority of the thread that was running the sketch to THREAD_PRIORITY_HIGHEST but that didn't change the results. When I was using the I2C-controlled pin I tried the same and the timings got ways worse (increasing more than 10 times) and so I did not commented on that part, wanting to investigate the issua a bit more in detail. It seems that increasing the priority of the application thread impacts negatively the I2C communication. I tried to use also the Linux-based implementation (using a different Galileo board since the one provided by MS seems to use a different firmware) and the results of running the sample blink sketch modified to use pin 2 and blink the led for 1ms are similar to those we got on the same board running Windows. Here the difference between expected time and measured time is worse, getting around 3.2ms instead of 1 (320% compared to 150% using Windows but far from the 100.1% we got with the 8-bit Arduino). Both systems were not under load during the test, maybe loading some applications that use part of the CPU time would make those timings even less reliable, but I think that those numbers are enough to draw some conclusions. It may not be worth running a full OS if what you need is Arduino compatibility. The Arduino UNO is probably the best Arduino you can find to perform this kind of development. The Galileo running the Linux-based stack or running Windows for IoT is targeted to be a platform for "Internet of Things" devices, whatever that means. At the moment I don't see the "I" part of IoT. We have low level interfaces (SPI, I2C, the GPIO pins) that can be used to connect sensors but the support for connectivity is limited and the amount of work required to deliver some data to the cloud (using a secure HTTP request or a message queuing system like APMQS or MQTT) is still big and the rich OS underneath seems to not provide any help doing that.Why should I use sockets and can't access all the high level connectivity features we have on "full" Windows?I know that it's possible to use some third party libraries, try to build them using the Windows For IoT SDK etc. but this means re-inventing the wheel every time and can also lead to some IP concerns if used for products meant to be closed-source. I hope that MS and Intel (and others) will focus less on the "coolness" of running (some) Arduino sketches and more on providing a better platform to people that really want to design devices that leverage internet connectivity and the cloud processing power to deliver better products and services. Providing a reliable set of connectivity services would be a great start. Providing support for .NET would be even better, leaving native code available for hardware access etc. I know that those components may require additional storage and memory etc. So making the OS componentizable (or, at least, provide a way to install additional components) would be a great way to let developers pick the parts of the system they need to develop their solution, knowing that they will integrate well together. I can understand that the Arduino and Raspberry Pi* success may have attracted the attention of marketing departments worldwide and almost any new development board those days is promoted as "XXX response to Arduino" or "YYYY alternative to Raspberry Pi", but this is misleading and prevents companies from focusing on how to deliver good products and how to integrate "IoT" features with their existing offer to provide, at the end, a better product or service to their customers. Marketing is important, but can't decide the key features of a product (the OS) that is going to be used to develop full products for end customers integrating it with hardware and application software. I really like the "hackable" nature of open-source devices and like to see that companies are getting more and more open in releasing information, providing "hackable" devices and supporting developers with documentation, good samples etc. On the other side being able to run a sketch designed for an 8 bit microcontroller on a full-featured application processor may sound cool and an easy upgrade path for people that just experimented with sensors etc. on Arduino but it's not, in my humble opinion, the main path to follow for people who want to deliver real products.   *Shameless self-promotion: if you are looking for a good book in Italian about the Raspberry Pi , try mine: http://www.amazon.it/Raspberry-Pi-alluso-Digital-LifeStyle-ebook/dp/B00GYY3OKO

  Read the article

• laptop crashed: why?

  - by sds

  my linux (ubuntu 12.04) laptop crashed, and I am trying to figure out why. # last sds pts/4 :0 Tue Sep 4 10:01 still logged in sds pts/3 :0 Tue Sep 4 10:00 still logged in reboot system boot 3.2.0-29-generic Tue Sep 4 09:43 - 11:23 (01:40) sds pts/8 :0 Mon Sep 3 14:23 - crash (19:19) this seems to indicate a crash at 09:42 (= 14:23+19:19). as per another question, I looked at /var/log: auth.log: Sep 4 09:17:02 t520sds CRON[32744]: pam_unix(cron:session): session closed for user root Sep 4 09:43:17 t520sds lightdm: pam_unix(lightdm:session): session opened for user lightdm by (uid=0) no messages file syslog: Sep 4 09:24:19 t520sds kernel: [219104.819975] CPU0: Package power limit normal Sep 4 09:43:16 t520sds kernel: imklog 5.8.6, log source = /proc/kmsg started. kern.log: Sep 4 09:24:19 t520sds kernel: [219104.819969] CPU1: Package power limit normal Sep 4 09:24:19 t520sds kernel: [219104.819971] CPU2: Package power limit normal Sep 4 09:24:19 t520sds kernel: [219104.819974] CPU3: Package power limit normal Sep 4 09:24:19 t520sds kernel: [219104.819975] CPU0: Package power limit normal Sep 4 09:43:16 t520sds kernel: imklog 5.8.6, log source = /proc/kmsg started. Sep 4 09:43:16 t520sds kernel: [ 0.000000] Initializing cgroup subsys cpuset Sep 4 09:43:16 t520sds kernel: [ 0.000000] Initializing cgroup subsys cpu I had a computation running until 9:24, but the system crashed 18 minutes later! kern.log has many pages of these: Sep 4 09:43:16 t520sds kernel: [ 0.000000] total RAM covered: 8086M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 64K num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 128K num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 256K num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 512K num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 1M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 2M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 4M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 8M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 16M num_reg: 10 lose cover RAM: 38M Sep 4 09:43:16 t520sds kernel: [ 0.000000] *BAD*gran_size: 64K chunk_size: 32M num_reg: 10 lose cover RAM: -16M Sep 4 09:43:16 t520sds kernel: [ 0.000000] *BAD*gran_size: 64K chunk_size: 64M num_reg: 10 lose cover RAM: -16M Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 128M num_reg: 10 lose cover RAM: 0G Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 256M num_reg: 10 lose cover RAM: 0G Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 512M num_reg: 10 lose cover RAM: 0G Sep 4 09:43:16 t520sds kernel: [ 0.000000] gran_size: 64K chunk_size: 1G num_reg: 10 lose cover RAM: 0G Sep 4 09:43:16 t520sds kernel: [ 0.000000] *BAD*gran_size: 64K chunk_size: 2G num_reg: 10 lose cover RAM: -1G does this mean that my RAM is bad?! it also says Sep 4 09:43:16 t520sds kernel: [ 2.944123] EXT4-fs (sda1): INFO: recovery required on readonly filesystem Sep 4 09:43:16 t520sds kernel: [ 2.944126] EXT4-fs (sda1): write access will be enabled during recovery Sep 4 09:43:16 t520sds kernel: [ 3.088001] firewire_core: created device fw0: GUID f0def1ff8fbd7dff, S400 Sep 4 09:43:16 t520sds kernel: [ 8.929243] EXT4-fs (sda1): orphan cleanup on readonly fs Sep 4 09:43:16 t520sds kernel: [ 8.929249] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 658984 ... Sep 4 09:43:16 t520sds kernel: [ 9.343266] EXT4-fs (sda1): ext4_orphan_cleanup: deleting unreferenced inode 525343 Sep 4 09:43:16 t520sds kernel: [ 9.343270] EXT4-fs (sda1): 56 orphan inodes deleted Sep 4 09:43:16 t520sds kernel: [ 9.343271] EXT4-fs (sda1): recovery complete Sep 4 09:43:16 t520sds kernel: [ 9.645799] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) does this mean my HD is bad? As per FaultyHardware, I tried smartctl -l selftest, which uncovered no errors: smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-30-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Momentus 7200.4 Device Model: ST9500420AS Serial Number: 5VJE81YK LU WWN Device Id: 5 000c50 0440defe3 Firmware Version: 0003LVM1 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Mon Sep 10 16:40:04 2012 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 109) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103b) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 117 099 034 Pre-fail Always - 162843537 3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 571 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 069 060 030 Pre-fail Always - 17210154023 9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 174362787320258 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 571 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 1 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 061 043 045 Old_age Always In_the_past 39 (0 11 44 26) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 84 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 20 193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 2434 194 Temperature_Celsius 0x0022 039 057 000 Old_age Always - 39 (0 15 0 0) 195 Hardware_ECC_Recovered 0x001a 041 041 000 Old_age Always - 162843537 196 Reallocated_Event_Count 0x000f 095 095 030 Pre-fail Always - 4540 (61955, 0) 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 4545 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. Googling for the messages proved inconclusive, I can't even figure out whether the messages are routine or catastrophic. So, what do I do now?

  Read the article

• CPU Usage in Very Large Coherence Clusters

  - by jpurdy

  When sizing Coherence installations, one of the complicating factors is that these installations (by their very nature) tend to be application-specific, with some being large, memory-intensive caches, with others acting as I/O-intensive transaction-processing platforms, and still others performing CPU-intensive calculations across the data grid. Regardless of the primary resource requirements, Coherence sizing calculations are inherently empirical, in that there are so many permutations that a simple spreadsheet approach to sizing is rarely optimal (though it can provide a good starting estimate). So we typically recommend measuring actual resource usage (primarily CPU cycles, network bandwidth and memory) at a given load, and then extrapolating from those measurements. Of course there may be multiple types of load, and these may have varying degrees of correlation -- for example, an increased request rate may drive up the number of objects "pinned" in memory at any point, but the increase may be less than linear if those objects are naturally shared by concurrent requests. But for most reasonably-designed applications, a linear resource model will be reasonably accurate for most levels of scale. However, at extreme scale, sizing becomes a bit more complicated as certain cluster management operations -- while very infrequent -- become increasingly critical. This is because certain operations do not naturally tend to scale out. In a small cluster, sizing is primarily driven by the request rate, required cache size, or other application-driven metrics. In larger clusters (e.g. those with hundreds of cluster members), certain infrastructure tasks become intensive, in particular those related to members joining and leaving the cluster, such as introducing new cluster members to the rest of the cluster, or publishing the location of partitions during rebalancing. These tasks have a strong tendency to require all updates to be routed via a single member for the sake of cluster stability and data integrity. Fortunately that member is dynamically assigned in Coherence, so it is not a single point of failure, but it may still become a single point of bottleneck (until the cluster finishes its reconfiguration, at which point this member will have a similar load to the rest of the members). The most common cause of scaling issues in large clusters is disabling multicast (by configuring well-known addresses, aka WKA). This obviously impacts network usage, but it also has a large impact on CPU usage, primarily since the senior member must directly communicate certain messages with every other cluster member, and this communication requires significant CPU time. In particular, the need to notify the rest of the cluster about membership changes and corresponding partition reassignments adds stress to the senior member. Given that portions of the network stack may tend to be single-threaded (both in Coherence and the underlying OS), this may be even more problematic on servers with poor single-threaded performance. As a result of this, some extremely large clusters may be configured with a smaller number of partitions than ideal. This results in the size of each partition being increased. When a cache server fails, the other servers will use their fractional backups to recover the state of that server (and take over responsibility for their backed-up portion of that state). The finest granularity of this recovery is a single partition, and the single service thread can not accept new requests during this recovery. Ordinarily, recovery is practically instantaneous (it is roughly equivalent to the time required to iterate over a set of backup backing map entries and move them to the primary backing map in the same JVM). But certain factors can increase this duration drastically (to several seconds): large partitions, sufficiently slow single-threaded CPU performance, many or expensive indexes to rebuild, etc. The solution of course is to mitigate each of those factors but in many cases this may be challenging. Larger clusters also lead to the temptation to place more load on the available hardware resources, spreading CPU resources thin. As an example, while we've long been aware of how garbage collection can cause significant pauses, it usually isn't viewed as a major consumer of CPU (in terms of overall system throughput). Typically, the use of a concurrent collector allows greater responsiveness by minimizing pause times, at the cost of reducing system throughput. However, at a recent engagement, we were forced to turn off the concurrent collector and use a traditional parallel "stop the world" collector to reduce CPU usage to an acceptable level. In summary, there are some less obvious factors that may result in excessive CPU consumption in a larger cluster, so it is even more critical to test at full scale, even though allocating sufficient hardware may often be much more difficult for these large clusters.

  Read the article

• Identity Globe Trotters (Sep Edition): The Social Customer

  - by Tanu Sood

  Welcome to the inaugural edition of our monthly series - Identity Globe Trotters. Starting today, the last Friday of every month, we will explore regional commentary on Identity Management. We will invite guest contributors from around the world to share their opinions and experiences around Identity Management and highlight regional nuances, specific drivers, solutions and more. Today's feature is contributed by Michael Krebs, Head of Business Development at esentri consulting GmbH, a (SOA) specialized Oracle Gold Partner based in Ettlingen, Germany. In his current role, Krebs is dealing with the latest developments in Enterprise Social Networking and the Integration of Social Media within business processes.  By Michael Krebs The relevance of "easy sign-on" in the age of the "Social Customer" With the growth of Social Networks, the time people spend within those closed "eco-systems" is growing year by year. With social networks looking to integrate search engines, like Facebook announced some weeks ago, their relevance will continue to grow in contrast to the more conventional search engines. This is one of the reasons why social network accounts of the users are getting more and more like a virtual fingerprint. With the growing relevance of social networks the importance of a simple way for customers to get in touch with say, customer care or contract departments, will be crucial for sales processes in critical markets. Customers want to have one single point of contact and also an easy "login-method" with no dedicated usernames, passwords or proprietary accounts. The golden rule in the future social media driven markets will be: The lower the complexity of the initial contact, the better a company can profit from social networks. If you, for example, can generate a smart way of how an existing customer can use self-service portals, the cost in providing phone support can be lowered significantly. Recruiting and Hiring of "Digital Natives" Another particular example is "social" recruiting processes. The so called "digital natives" don´t want to type in their profile facts and CV´s in proprietary systems. Why not use the actual LinkedIn profile? In German speaking region, the market in the area of professional social networks is dominated by XING, the equivalent to LinkedIn. A few weeks back, this network also opened up their interfaces for integrating social sign-ons or the usage of profile data for recruiting-purposes. In the European (and especially the German) employment market, where the number of young candidates is shrinking because of the low birth rate in the region, it will become essential to use social-media supported hiring processes to find and on-board the rare talents. In fact, you will see traditional recruiting websites integrated with social hiring to attract the best talents in the market, where the pool of potential candidates has decreased dramatically over the years. Identity Management as a key factor in the Customer Experience process To create the biggest value for customers and also future employees, companies need to connect their HCM or CRM-systems with powerful Identity management solutions. With the highly efficient Oracle (social & mobile enabling) Identity Management solution, enterprises can combine easy sign on with secure connections to the backend infrastructure. This combination enables a "one-stop" service with personalized content for customers and talents. In addition, companies can collect valuable data for the enrichment of their CRM-data. The goal is to enrich the so called "Customer Experience" via all available customer channels and contact points. Those systems have already gained importance in the B2C-markets and will gradually spread out to B2B-channels in the near future. Conclusion: Central and "Social" Identity management is key to Customer Experience Management and Talent Management For a seamless delivery of "Customer Experience Management" and a modern way of recruiting the best talent, companies need to integrate Social Sign-on capabilities with modern CX - and Talent management infrastructure. This lowers the barrier for existing and future customers or employees to get in touch with sales, support or human resources. Identity management is the technology enabler and backbone for a modern Customer Experience Infrastructure. Oracle Identity management solutions provide the opportunity to secure Social Applications and connect them with modern CX-solutions. At the end, companies benefit from "best of breed" processes and solutions for enriching customer experience without compromising security. About esentri: esentri is a provider of enterprise social networking and brings the benefits of social network communication into business environments. As one key strength, esentri uses Oracle Identity Management solutions for delivering Social and Mobile access for Oracle’s CRM- and HCM-solutions. …..End Guest Post…. With new and enhanced features optimized to secure the new digital experience, the recently announced Oracle Identity Management 11g Release 2 enables organizations to securely embrace cloud, mobile and social infrastructures and reach new user communities to help further expand and develop their businesses. Additional Resources: Oracle Identity Management 11gR2 release Oracle Identity Management website Datasheet: Mobile and Social Access (pdf) IDM at OOW: Focus on Identity Management Facebook: OracleIDM Twitter: OracleIDM We look forward to your feedback on this post and welcome your suggestions for topics to cover in Identity Globe Trotters. Last Friday, every month!

  Read the article

< Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >