Search Results

Search found 14588 results on 584 pages for 'usb drive'.

Page 147/584 | < Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >

  • Is my hard drive about to die?

    - by Hristo Deshev
    I have two hard drives set up as a RAID 1 array on my server (Linux, software RAID using mdadm) and one of them just got me this "present" in syslog: Nov 23 02:05:29 h2 kernel: [7305215.338153] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:29 h2 kernel: [7305215.338178] ata1.00: irq_stat 0x40000008 Nov 23 02:05:29 h2 kernel: [7305215.338197] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:29 h2 kernel: [7305215.338220] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:29 h2 kernel: [7305215.338221] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:29 h2 kernel: [7305215.338287] ata1.00: status: { DRDY ERR } Nov 23 02:05:29 h2 kernel: [7305215.338305] ata1.00: error: { UNC } Nov 23 02:05:29 h2 kernel: [7305215.358901] ata1.00: configured for UDMA/133 Nov 23 02:05:32 h2 kernel: [7305218.269054] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:32 h2 kernel: [7305218.269081] ata1.00: irq_stat 0x40000008 Nov 23 02:05:32 h2 kernel: [7305218.269101] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:32 h2 kernel: [7305218.269125] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:32 h2 kernel: [7305218.269126] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:32 h2 kernel: [7305218.269196] ata1.00: status: { DRDY ERR } Nov 23 02:05:32 h2 kernel: [7305218.269215] ata1.00: error: { UNC } Nov 23 02:05:32 h2 kernel: [7305218.341565] ata1.00: configured for UDMA/133 Nov 23 02:05:35 h2 kernel: [7305221.193342] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:35 h2 kernel: [7305221.193368] ata1.00: irq_stat 0x40000008 Nov 23 02:05:35 h2 kernel: [7305221.193386] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:35 h2 kernel: [7305221.193408] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:35 h2 kernel: [7305221.193409] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:35 h2 kernel: [7305221.193474] ata1.00: status: { DRDY ERR } Nov 23 02:05:35 h2 kernel: [7305221.193491] ata1.00: error: { UNC } Nov 23 02:05:35 h2 kernel: [7305221.388404] ata1.00: configured for UDMA/133 Nov 23 02:05:38 h2 kernel: [7305224.426316] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:38 h2 kernel: [7305224.426343] ata1.00: irq_stat 0x40000008 Nov 23 02:05:38 h2 kernel: [7305224.426363] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:38 h2 kernel: [7305224.426387] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:38 h2 kernel: [7305224.426388] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:38 h2 kernel: [7305224.426459] ata1.00: status: { DRDY ERR } Nov 23 02:05:38 h2 kernel: [7305224.426478] ata1.00: error: { UNC } Nov 23 02:05:38 h2 kernel: [7305224.498133] ata1.00: configured for UDMA/133 Nov 23 02:05:41 h2 kernel: [7305227.400583] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x0 Nov 23 02:05:41 h2 kernel: [7305227.400608] ata1.00: irq_stat 0x40000008 Nov 23 02:05:41 h2 kernel: [7305227.400627] ata1.00: failed command: READ FPDMA QUEUED Nov 23 02:05:41 h2 kernel: [7305227.400649] ata1.00: cmd 60/08:00:d8:df:da/00:00:3a:00:00/40 tag 0 ncq 4096 in Nov 23 02:05:41 h2 kernel: [7305227.400650] res 41/40:08:d8:df:da/00:00:3a:00:00/00 Emask 0x409 (media error) <F> Nov 23 02:05:41 h2 kernel: [7305227.400716] ata1.00: status: { DRDY ERR } Nov 23 02:05:41 h2 kernel: [7305227.400734] ata1.00: error: { UNC } Nov 23 02:05:41 h2 kernel: [7305227.472432] ata1.00: configured for UDMA/133 From what I read so far, I am not sure if read errors mean that a hard drive is dying on me (no write errors so far). I've had hard drive errors in the past and those always had errors about failing to write to specific sectors in the logs. Not this time. Should I be replacing the drive? Could something else be causing the problem? I've scheduled a smartctl -t long test that will finish in a couple of hours. I hope this will give me some more info.

    Read the article

  • Why my internal hard disk can be ejected?

    - by Bear Bear
    I have 6 hard disks in my computer and one DVD. The disk that I connect to the 6th SATA port is a regular disk. But my Windows 7 64 bit shows it as a removable drive. I can eject my hard disk! Just like a pen drive. If I connect another disk to the 6th port, I can eject that disk too. So it has nothing to do with the physical disk, it must be something related to Windows or BIOS I don't understand why Windows 7 is seeing a normal hard disk as removable. In Computer Management - Disk Management, the disk looks identical to the others - there is nothing there to suggest the drive is different from the others. But in the tray I have the icon to eject it. The motherboard model is ASUS F2A85 V PRO FM2. All the disks are formatted normally, no Dynamic Disk, no RAID, nothing special. How can I tell Windows 7 to treat the disk exactly like the others, so it can't be ejected?

    Read the article

  • unreadable corrupted ntfs partition - lost clusters reported

    - by Eduardo Martinez
    Hi, partition magic is reporting multiple 'bad file record signature' and 'lost clusters' errors on my 250GB samsung sata disk (connected via usb on a xp sp3). Unfortunately PM is unable to fix. PM shows the drive as being NTFS, detects used space ok and also drive name. But PM browser (right click on partition, browse...) won't show anything (as if disk was empty) Windows Explorer is not even picking the drive name and reports 'the file or directory is corrupted and unreadable' PTDD partition table doctor demo tells me the boot sector is fine, and I can see all disk content on its browser - but crucially cannot copy that content over to a new disk (PTDD browser is pretty arid to say the least) Also tried - photorec-6.11.3 - it actually started to extract files but wouldn't keep file names or any folder structure (maybe I missed sth on the configuration options) - find and mount - intellectual scan went well, the only partition on the disk was detected, then tried to mount into p: but got this error on windows explorer: 'p:\ is not accesible. The media is write protected'. Find and mount allows you to create an image from partition but I don't have a disk big enough at hand. Does anyone know if this will keep the extracted files/folders structure intact? I'm starting to think the disk is pretty screwed and my chances to recover this data are slim. Please someone enlighten me with that marvellous piece of software I am missing :-) Thanks in advance

    Read the article

  • raid 0 data recovery?

    - by Fred
    HI All, I have two identical seagate 7200.9 500Gb drives confiured as a RAID 0 spanned disk in windows. One of the drives has lost power and wont spin up at all. I know this normally means death for the data on both drives but i have a cunning plan.. DISK 1 - NO POWER RAID 0 DISK DISK 2 - FULLY FUNCTIONAL RAID 0 DISK DISK 3 - FULLY FUNCTIONAL SPARE DISK Copy the working drive (disk 2) data to a third 500GB DISK (disk 3), remove the logic board from the working disk (disk 2) and replace it with the non working logic board on the broken drive (disk 1) , then hopefully recreate the RAID 0 with disk 1 and disk 3, just long enough to get the data off it. Hope this makes sense, here are my questions: Windows disk manager atm recognises disk 2 but wont let me access it in anyway, therefore copying the data off it (or getting a disk image) cant be done in windows. Does anyone know of any software (in linux or self booting) that would allow me to access this disk? Anyone know of any software that will recreate the spanned drive off two disk images Am i missing any key information that means i definitely shouldn't even bother starting this, i know its a long shot anyway but its worth a try unless i definitely cant do it. The irritating thing is that i am sure its a logic board failure on disk 1 as it simply wont power up at all, suddenly no signs of life, so i am sure the data is intact! Any help would be really appreciated! Thanks

    Read the article

  • ExpressCache not working after Windows 8 reinstall on Samsung Series 7 Gamer

    - by Morven
    I have a Samsung Series 7 Gamer laptop which came with Windows 8. After doing a reinstall of Windows, the ExpressCache software is no longer caching. Running "eccmd -info" shows me that the software is present and it has the MSATA drive partition configured. However, it's not actually caching anything. These are the results after having the system booted for days: C:\windows\system32eccmd -info ExpressCache Command Version 1.0.94.0 Copyright¬ 2010-2012 Condusiv Technologies. Date Time: 11/3/2013 12:26:20:263 (JAMETHIEL #36) EC Cache Info ================================================== Mounted : Yes Partition Size : 7.46 GB Reserved Size : 3.00 MB Volume Size : 7.46 GB Total Used Size : 86.50 MB Total Free Space : 7.38 GB Used Data Size : 16.63 MB Used Data Size on Disk : 84.38 MB Tiered Cache Stats ================================================== Memory in use : 32.00 MB Blocks in use : 136 Read Percent : 0.02% Cache Stats ================================================== Cache Volume Drive Number : 1 Total Read Count : 97242 Total Read Size : 4.13 GB Total Cache Read Count : 0 Total Cache Read Size : 595.50 KB Total Write Count : 161546 Total Write Size : 5.89 GB Total Cache Write Count : 0 Total Cache Write Size : 0 Bytes Cache Read Percent : 0.01% Cache Write Percent : 0.00% As you can see on the last two lines, cache read and write percent is nigh on zero. Anyone know where to look next? The only guides I can find deal with ExpressCache not being present or not having a configured drive.

    Read the article

  • Alienware Aurora R2 Slow Boot Up

    - by James R
    I have an Aurora R2 bought a few years ago, and recently I decided a RAM update and new Samsung SSD would be good for speed. So now it's super fast, with the exception of booting up. It still takes good 2 minutes to get past the first splash screen on the BIOS, it's only the BIOS, after that it's like lightning. I've Googled the issue, and the usual problem is the BIOS trying to boot from anything it can, with the fix being to change the boot menu. However I've changed it now, and it's still slow. When I disconnect the USB devices it speeds up, but I can't do that every time I want to boot the PC up! The only other option I can think of is upgrading the BIOS, however it seems that A04 is the recommended on for Aurora R2s, so I don't know if upgrading the BIOS could cause issues, especially not if it doesn't solve the issue. Also, when I disable my original hard drive in the boot menu, the PC won't boot up. Despite the Samsung one being fine to boot from, and the original not being needed as far as I know for starting Windows, it gives me an error message and makes me restart the PC, with a new boot configuration (with the original drive as second choice). Any ideas on how to make the BIOS boot faster? And why I need to have my original drive in the boot menu?

    Read the article

  • How to get data from a borked Windows Home Server

    - by harhoo
    Yesterday we had a power surge, followed by a power outage. This left my WHS borked: powering on just gives to a flashing blue light (the led on the power supply also flashes green) - no fan or boot activity, nothing. I urgently needed some files off there in the short term (and the 500GB of photos, music, personal video etc in the long term) so I took the hard drive out and put it in my computer. The files and folders showed up, but I couldn't access them - clicking on an image gave an invalid image error in Picasa, I couldn't play MP3s etc. I changed the ownership and permissions of the files, still nothing. I booted in with a LiveCD, the same: files appear, but won't open. Is there anything else I can do? I'm now wondering if it was just the power cable that's broken, but if so, why can;t I access my files from the hard drive? If it is the power cable, and I replace that and the hard drive, will I have done any harm messing around with ownership and file permissions?

    Read the article

  • BIOS and Windows cannot detect CDROM device

    - by eman
    Hello! I have a HL-DT-ST RW/DVD GCC-4521B dvdrom device and a big problem. Some days ago everything worked fine. A friend installed some software and then the drives in winxp has been marked as corrupt. I uninstalled the software, but still corrupt drives. The next step I have done was running the current software GCC-4521B101(E).exe. When I ran this software again, the drives was automatically updated, but still marked as corrupt (in the Device Manager), even if I did a reboot. And then the big mistake: once more I tried to run this software, but during the update process, the machine restarted and boom! The DVDROM device doesn't work anymore. The led doesn't blink and if I push the eject button, nothing happens. Also bios and winxp doesn't recognize the optical drive. Then I plugged an other optical drive and it worked, but my old drive seems to be dead. So, what happened and how to solve this problem? Please help. Regards!

    Read the article

  • Western Digital HDD disappears and reappears in BIOS

    - by tbkn23
    I know many people asked about similar problems, but I have a very specific case where I can't understand what's going on... I have a 3TB Western Digital Caviar Green disk connected in my Desktop, that also has a seagate 1.5TB disk and 2 SSD drives (OCZ and Sandisk). After working fine for quite some time (probably more than a year), suddenly my Caviar Green drive disappeared from windows. I checked the BIOS, and it wasn't there either. I opened my PC, played with the connectors, power, etc, but nothing helped. Even tried switching connectors with those of the 1.5TB disk, and nothing changed, the 1.5TB seagate was there, but the 3TB WD was not. Ok, now for the strange part. I have another desktop at home, so I took out my 3TB drive, connected it there, and it worked fine! I copied the most important files out of it, and then made another attempt in the original desktop. Surprise! It now appeared in the BIOS and worked fine! I even ran the SMART test with the WD tools and it said everything was intact. It doesn't end here. After leaving it overnight in the original desktop, it disappeared again in the morning. I repeated the entire process, connecting it to the second desktop, and there it is again working fine. Now for my question... Whats going on? The disk seems to be appearing on/off in my original Desktop, while other drives there work fine. SMART test says the disk is fine. Any ideas? Is the disk defective and should be replaced? Or maybe there's a problem with the controller in the desktop? I'm using a Gigabyte GA-880GA-UD3H motherboard and tried connecting the drive to both bridges (SATA2 and SATA3 bridges). Thanks EDIT: Power options are set never to turn off hard drives:

    Read the article

  • External HDD incorrectly detected as internal - how change to enable hot swap/eject?

    - by Sam
    I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: How do I remove the option to eject SATA drives from the Windows 7 tray icon?

    Read the article

  • Computer not finding hard drives on boot -sometimes-

    - by todd.pund
    Computer specs: Mobo: Gigabyte ultradurable 3 - GA-970A-UD3 Processor: First gen I7 3.2GHZ Ram: 8GB Kingston DDR3 1066 Video Card: EVGA NVidia GTX 460 1GB Hard Drive: 500MB 7200rpm x2 (can't remember brand, sorry I'm at work.) Last week my developer preview for Windows 8 ran out so I put my copy of windows 7 back on the computer. The computer at that point started suffering from frequent freezing and crashing. When I rebooted the computer sometimes it wouldn't find the system HD at all. When I looked at the post screen it seemed to show that it wasn't finding either of the HDs. Then yesterday when turning on the computer I just got GRUB as a message (not a GRUB prompt, just GRUB) I haven't had a dual boot of Linux for at least a year. I loaded windows 7 recovery console from the disk and ran: bootrec /fixboot bootrec /fixmbr Which did not help. At that point I just installed Ubuntu 13.04 over the windows 7 install and still received the GRUB post. I went into the BIOS and switched the Hard Drive priorities and then it loaded into Ubuntu fine. For several days everything was just hunky dory until I installed the Ubuntu version of Steam, install Portal and tried to run it. At that point the computer froze and after hard rebooting couldn't find the hard disks again. Then after restarting the system it loaded up fine again and no issues since. (I have not tried to launch portal again). My next thought is to remove the system hard drive and try to use the secondary as the master to see if the primary HD is bad. I'm sorry if this has been confusing, I'll answer any questions I can. Any thoughts?

    Read the article

  • Windows 7 explorer crashing trying to read external hard disk

    - by Mario De Schaepmeester
    I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

    Read the article

  • Hard Disk based storage library

    - by Ryan M.
    We have a Tandberg T24 tape device to handle all of our long term backups right now. We decided that we're not backing up nearly everything that we would like to and that we still have a lot of vulnerabilities. To get to where we want to be, we're going to have to back up a lot more servers than we're currently doing. All of our internal servers have some sort of directly attached drive (I.e. LaCie Raid box or a simple portable hard drive) doing backups, but what we want to do is get those backups off-site. The current tape drive is directly attached via SCSI to a Windows Server 2008 File Server. So to back up anything to tape, it has to be funneled through the File Server. With the current increase that we have planned, I don't think that funneling everything through the File Server is the right course of action and I'm thinking that maybe a second backup device would be more appropriate. I would like your input on a couple of ideas. 1) Doing HDD instead of tape. Tape is hard to deal with. We have a regular rotation cycle, so they don't need years and years of shelf life, so I'm wondering if something HDD-based would be better. 2) Something accessible over the network. Instead of having the device directly attached to one specific machine, have it available to all the servers over the network. Our File Server is a 12-disk raid 6 set up.. I was thinking something like that, but with no raid involved, all disks are stand alone so they can be used/installed/removed on an individual basis. Does any such thing exist? Thanks for your ideas. I'm really interested to hear about some of the solutions you guys are using..

    Read the article

  • How should I configure backup of my server?

    - by ed209
    I have just rented a dedicated server. If it helps this is the config I have: CPU1 Intel(R) Core(TM) i7-2600 CPU @ 3.40GHz (Cores 8) RAM 15975 MB Disk /dev/sda doesn't contain a valid partition table (=> /dev/sda doesn't) Disk /dev/sdc doesn't contain a valid partition table (=> /dev/sdc doesn't) Disk /dev/sdb doesn't contain a valid partition table (=> /dev/sdb doesn't) Disk /dev/sda: 120.0 GB (=> 114 GIB) Disk /dev/sdc: 3000.6 GB (=> 2861 GIB) Disk /dev/sdb: 3000.6 GB (=> 2861 GIB) /dev/sda is a 120GB SSD. This is where I have Ubuntu/lamp installed. It's the drive that will run my site. With the account I got two other drives of 3000GB each which I really don't need but they came with the account. I figured I could use these to back up my main 120gb drive. So a couple of things I wondered were: Should I use these for backups? How should I back up. The data I want to back up is a user uploads directory full of images and the database. Everything else is either in a code repo or backed up some other way. For example, it would be nice to know there is a disk image of the 120gb drive somewhere that I can copy over should there be any problems but equally I don't mind doing a fresh install of all the software and copying over just the images and database dump. Thanks for your advice! (also, happy to not use the two other drives and backup elsewhere if it's more sensible)

    Read the article

  • Boot stuck at blinking cursor before GRUB - only works via BIOS boot menu

    - by delta1
    I have a new box running Debian Squeeze. Grub is installed on /dev/sda, but when booting up I just get a blinking cursor, before the Grub menu. I can only boot to grub successfully when I choose boot options (during post) and select that specific drive! I have made sure the correct drive is set to boot first in the BIOS. So Grub works, but the system won't boot to that drive automatically? Any ideas on what could cause this? Drives sda/b/c are all 2TB (sda runs the system with b/c as raid device md0) with the following partitions: $ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 977 sda1 8 2 9765625 sda2 8 3 6445313 sda3 8 4 1937302627 sda4 8 32 1953514584 sdc 8 16 1953514584 sdb 9 0 1953513424 md0 but # fdisk -l /dev/sda gives WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 1 243202 1953514583+ ee GPT Any insight into this strange behaviour would be greatly appreciated.

    Read the article

  • How can I extract data from Toshiba Satellite with a dead Windows installation?

    - by msanford
    I've got a Toshiba Satellite (unknown model number but bought early 2010) running Windows Vista which throws a kernel error on boot. We don't have the restore/recovery CD any more to restore the Windows partition. I have managed to boot to a Live CD version of Ubuntu 10.10 and have mounted the internal hard drive (which takes nearly 8 minutes). I suspect that the hard drive is malfunctioning, however, because copy tasks of even 30 megs of data to an attached and mounted USB flash drive takes over an hour, and some files are mysteriously inaccessible (not a permissions issue). When browsing folders, it takes many minutes to populate the folder window even with a single tiny file. During the copy tasks, the hard disk sounds like it tries to sleep several times in rapid succession, then continues accessing, it sounds, at full throughput. I initially tried using scp (from the shell) to copy data but I encountered the same local problems. I don't know the S.M.A.R.T. status of the hard disk, either. Is there a more effective way of going about recovering the data on the internal disk, assuming that I can't use a recovery CD and am too cheap to bring it in (for now, at least)?

    Read the article

  • Corsair SSD appears completely blank and does not retain written data

    - by ebanders
    I have a 180GB Corsair SSD (model# CSSD-F180GB2-BRKT) as the primary drive in a Windows laptop. Recently the machine became unbootable after installing Windows updates. Windows installed updates before the machine shut down and the next time the machine boot up it complained about not being able to find a bootable device. After finding fixmbr unsuccessful at making the machine unbootable, I investigated a little within knoppix. Fdisk revealed an empty partition table. A scan by Testdisk came up empty. And finally 'head -c 1024 | hd' reveals all zeros. Creating a primary partition spanning the whole disk completes successfully, but after a reboot the disk appears empty again. dmesg reveals no read or write errors. smartctl indicates that the drive is healthy- although the SMART attribute values do not appear to be read properly. "Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO" and "Threshold Page | INCONSISTENT IDENTITIES IN THE DATA" messages appear within the table of values. I don't have much experience with SSDs. Is this drive dead or something? Can anyone recommend any diagnostic tools that may be suited for diagnosing SSDs?

    Read the article

  • mdadm: Replacing array with entirely new drives

    - by hellfur
    I have a server with three 500GB drives, with most of my data in a RAID5 configuration spanning the three of them. I just purchased and installed four 1TB drives, and the intention is to move off of the old drives and onto the new ones. I have enough SATA ports and power connectors to power all seven of my drives at once, so I've kept the old RAID running while I figure out what to do with the new drives. My question is: Should I create a whole new array on the 1TB drives, then move everything over and reconfigure linux to boot from the new md arrays? Or should I just expand the array, swapping out each of the three 500GBs with the 1TB, then adding the final drive? I've read up on the mdadm extending drive setup, and it makes sense, but I imagine I would use one of the drives as a full backup while I move things over, then add that drive back into the array once things are up and running on three of the 1TB drives, so there's some complication in going that route as well... I'm just not sure which is safer/recommended.

    Read the article

  • Can the Dell PowerEdge T320 boot from a USB stick in hard drive emulation mode?

    - by Icydog
    I am trying to install FreeNAS on a Dell PowerEdge T320. I've followed the instructions here (http://doc.freenas.org/index.php/Burning_an_IMG_File) to write the .img file to four different USB sticks with dd if=FreeNAS-9.2.1.5-RELEASE-x64.img of=/dev/sde, but I can't boot off of any of them. When I try to boot, I get the following screen: F1 FreeBSD F2 FreeBSD F3 Drive 0 Then it auto-selects F1 and either prints # about once a second forever, or it sits with a blinking cursor doing nothing. Forum posts and the wiki page linked above say to set the USB boot emulation mode to hard disk (as opposed to auto or CD/DVD/floppy), and older Dell PowerEdge models including the T310 have this option in the BIOS settings, but I cannot find it on the T320 with the latest BIOS 2.1.2. I have even tried writing the USB image to a USB hard disk, but with the same lack of success. Has anyone been able to find this USB boot setting on a T320, or been able to boot FreeNAS/FreeBSD from USB in some other way on a T320?

    Read the article

  • How to hack airport extreme to support USB 3G modem?

    - by Mike Caron
    Has anyone out there ever tried to hack the Airport Extreme, specifically with regard to the USB port? There are many cellular routers available that provide WiFi sharing of a USB modem link. However, instead of buying yet another router, I'd like to use my expensive Airport Extreme with it. The AE has a USB port on the back, but it's been said that it only talks to printers. Is there a way to hack the USB driver on the AE to allow it to recognize a USB modem, then use that as the connectivity instead of the LAN? I would imagine that one could use OpenFirmware to boot something on the AE. If one can boot it, then one could provide access using SSH across the lan. Once access is granted, then let the hacking begin... but I don't know how to (a) get the mini-osx on to USB (is it the same as the ATV without a UI?) or (b) how to load up certain things once boot has begun.

    Read the article

  • What is the data transfer speeds within the disk, to other devices?

    - by Kumar
    I use Debian 6 on a HP Elitbook 6930 with 2Gigs of RAM. I was copying two AVI files, 1.5 GB in total, and noticed that the data copying was done at the rate of 4MB/sec. When I copy same AVIs to my Western Digital Passport 25G USB plugin drive the data transfer speed is 11+MB/sec. This speed is different if I plugin the drive to different USB ports. Interestingly, at work I also downloaded a 16MB IE8 exe on my virtual xp, run inside Oracle Sun Virtual Box, and it was downloaded AND saved within a second. We have a high speed network at work. :-) Why and how this difference in data speeds is possible?

    Read the article

  • How do I restore a non-system hard drive using Time Machine under OSX?

    - by richardtallent
    I dropped one of the external drives on my Mac Pro and it started making noises... so I bought a replacement drive. No biggie, that's why I have Time Machine, right? So now that I have the new drive up and initialized, how do I actually restore the drive from backup? Time Machine is intuitive when it comes to restoring the system drive or restoring individual folders/files on the same literal device, but I'm a bit stuck in how to properly restore an entire drive that is not the boot drive. I saw one suggestion to use the same volume name as the old drive and then go into Time Machine. Haven't tried that since the information is unconfirmed. For now, I just went to the Time Machine volume, found the latest backup folder for that volume, and I'm copying the files via Finder. Of couse, I expect this to work just fine, but I feel like I'm missing something if that's the "proper" way to do this.

    Read the article

  • How to Recover HDD Formatted by "Create a Recovery Drive" Tool of Windows 8.1?

    - by ide
    I have 2 TB USB HDD which had these drives F: about 1 TB with 750 GB data H: about 120 GB with 60 GB data I: about 780 GB with 250 GB data (For TV: It was raw in Windows but visible in the Smart TV) I took 521 MB from last part of H to get new G drive. Then I run "Create a Recovery Drive" tool of Windows 8.1 and chose G drive. It said all data in the drive will be deleted. I thought it is just G drive but it deleted my whole HDD. It created 32 GB new F drive with writing 337 MB on it and rest of HDD is unallocated. I tried these programs to get my first 3 drives but non of them helped for getting 1st partition. TestDisk MiniTool Partition Wizard Home Edition EaseUS Partition Master 9.2.2 (I deleted new F drive volume because it scans only unallocated part) Recuva PC Inspector File Recovery

    Read the article

  • Laptop HDD failure imminent?

    - by Andrei Rinea
    I have an HP Compaq 615 laptop with an 160 GB 7200 rpm HDD. Hasn't been dropped or shaken, in fact it almost always stayed on my desk. I've treated it as nice as I could. The other day, however, my OS froze and I could hear a repeated clink-clink-clink coming from the HDD zone of the laptop. I had to switch off hardware-ly the laptop and re-start it. It worked very well after, including now. However I backed up immediately the core data on my USB drive and ordered an external USB HDD for periodic backups. Will it die soon or it was just a "blip"?

    Read the article

  • New power supply and now HDDs are not recognized.

    - by Michael
    So I upgraded to a new X4 ULTRA power supply that was recommended to me by a local TigerDirect store. After installing it along with a new liquid cooling system, I booted it up and it automatically fried my CD Drive. After that I noticed that the OS wouldn't start and figured out that none of the 4 HDDs in my computer were being recognized by the BIOS. I feel them spool at a steady pace and have tried new cables and connections but to no avail. I triple checked all of the connections and cables and have no idea what is wrong. This isn't the first time I changed a PS or CPU cooling system but I am at a dead end. Any ideas, aside from buying a USB HDD reader and seeing if they are all fried? Also, this is a stock Gateway mobo with the mobo USB connections already dead. Could the new PS have fried the SATA connections??

    Read the article

< Previous Page | 143 144 145 146 147 148 149 150 151 152 153 154  | Next Page >