Search Results

Search found 4151 results on 167 pages for 'cat man do'.

Page 148/167 | < Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >

• Cannot install grub to RAID1 (md0)

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat This is the my mdadm output after sync: /dev/md0: Version : 0.90 Creation Time : Wed Feb 17 16:18:25 2010 Raid Level : raid1 Array Size : 470455360 (448.66 GiB 481.75 GB) Used Dev Size : 470455360 (448.66 GiB 481.75 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Nov 1 15:19:31 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 92e6ff4e:ed3ab4bf:fee5eb6c:d9b9cb11 Events : 0.11049560 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. This is my fdisk -l output: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00057d19 Device Boot Start End Blocks Id System /dev/sda1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sda2 940910985 976768064 17928540 5 Extended /dev/sda5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table This is my grub install output: root@answe:~# grub-install /dev/sda /usr/sbin/grub-setup: warn: Attempting to install GRUB to a disk with multiple partition labels or both partition label and filesystem. This is not supported yet.. /usr/sbin/grub-setup: error: embedding is not possible, but this is required for cross-disk install. root@answe:~# grub-install /dev/sdb Installation finished. No error reported. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... Anybody can resolve this issue? I have big headache with this.

  Read the article

• How much did it cost our competitor to DDoS us at 50 Gbps for two weeks?

  - by MiniQuark

  I know that this question may sound like an invalid serverfault question, but I believe that it's quite valid: the amount of time and effort that a sysadmin should spend on DDoS protection is a direct function of typical DDoS prices. Let me rephrase this: protecting a web site against small attacks is one thing, but resisting 50 Gbps of UDP flood is another and requires time & money. Deciding whether or not to spend that time & money depends on whether such an attack is likely or not, and this in turn depends on how cheap and simple such an attack is for the attacker. So here's the full story: our company has been victim to a massive DDoS attack (over 50 Gbps of UDP traffic, full-time during 2 weeks). We are pretty sure that it's one of our competitors, and we actually know which one, because we were the only two remaining competitors on a very big request for proposal, and the DDoS attack magically stopped the day we won (double hurray, by the way)! These people have proved in the past that they are very dishonest, but we know that they are not technical at all, so we believe that they simply paid for some botnet DDoS service. I would like to know how much these services typically cost, for such a large scale attack. Please do not give any link to such services, I would really hate to give these people any publicity. I understand that a hacker could very well do this for free, but what's a typical price for such an attack if our competitors paid for it through some kind of botnet service? It is really starting to scare me (if we're talking thousands of dollars here, then I am really going to freak off: who knows, they might just hire a hit-man one day?). Of course we filed a complaint, but the police says that they cannot do much about it (DDoS attacks are virtually untraceable, so they say), and our suspicions are not enough to justify them raiding our competitor's offices to search for proofs. For your information, we now changed our infrastructure to be able to sustain such attacks: we now use a major CDN service so that our servers are not directly affected by DDoS attacks. Requests for dynamic pages do get proxied to our servers, but for low level attacks (UDP flood, or Syn floods, for example) we only receive legitimate trafic, so we're fine. If they decide to launch higher level attacks (HTTP flood or slowloris attacks for example), most of the load should be handled by the CDN... at least I hope so! Thank you very much for your help.

  Read the article

• IIS httpTracing setting has no effect

  - by digahill

  I'm trying to troubleshoot some performance issues we are having on a specific ASP.NET page with Microsoft's Perfecto Tool on IIS 7.5. Perfecto uses the ETW hooks build in to IIS to report on specific HTTP request, and is working quite well. However, I only want IIS to emit traces for one specific page, say "Default.aspx" in my TestApp Web Application. Following the instructions on the httpTracing man page, I should be able to add the traceUrls element to my root web.config file for TestApp. This doesn't seem to affect tracing whatsoever when I do so. For example, I've used the following settings in the web.config file and every request that hits the IIS server is sending tracing messages that are in turn picked up by Perfecto. (In the System.WebServer section) <httpTracing> <traceUrls> <add value="/Default.aspx" /> </traceUrls> </httpTracing> I then found that the applicationHost.config file on the server had an empty element. I tried removing this element, as well as the httpTracing element in the web.config. After a machine reboot, I was still getting tracing messages! My understanding is that the presense of the httpTracing element is what controlls whether ETW tracing is on or not. I ensured there was no reference to httpTracing in the machine.config, too. At a loss, I decided to remove the IIS Tracing feature with Server Manager. After a reboot, I no longer got ETW tracing. I then reinstalled IIS Tracing feature with Server Manager. As expected, the httpTracing element reappeared in the applicationhost.config file. Tracing messages began sending again for all sites and pages. I then tried to use the traceUrls element at the applicationhost.config level. This also didn't filter out and traces. I must be misunderstanting something key with how httpTracing works. There aren't many resources on the web to help me, either. Can anyone tell me if what I'm trying should work? Has anyone else had success filtering tracing message per page with traceUrls? I should note that I also tried changing with the following setting in applicationhost.config to "allow". It didn't seem to help. <section name="httpTracing" overrideModeDefault="Allow" />

  Read the article

• Running an rsync sweep before initializing lsyncd for synchronizing instances on EC2

  - by chrisallenlane

  My company uses several EC2 servers that will scale up and down according to the load we're receiving on our sites at any given moment. For the sake of our discussion here, we're running four instances: master.ourdomain.com - the file syncing "hub" of the webservers www1/www2/www3.ourdomain.com - three webservers which turn on or off as dictated by load I'm using lsyncd to keep all of the webservers in sync, and for the most part, it's working quite well. We're using a two-way syncing scheme, such that each webserver syncs against master, and master syncs against each webserver. Thus, the webservers are kept in sync, even though they aren't syncing against each other directly. I'm having one problem that I'm having a hard time solving,though. It occurs under these circumstances: When changes are made on master (perhaps after we've pushed new code), while some of the redundant webservers are sleeping And then a sleeping webserver wakes-up to absorb load Under that circumstance, I would like the following to happen: First, the newly-awoken webserver should sync its file structure - one way - against master, to bring its web application code up-to-date. Then, and only then, should it begin pushing changes in its file structure back to master. Unfortunately, currently, when a sleeping server is started, when lsyncd starts up, it pushes changes back to master before updating its own codebase, thus overwriting new code with old. Thus, before lsyncd starts, I'd like to be able to synchronize the webservers code against master's, perhaps by running a simple one-way rsync against the two machines. We're running lsyncd v.2, and I've tried to make this happen by using the "bash" configuration options documented in the lsyncd manual. My configuration file looks like this: settings = { logfile = "/home/user/log/lsyncd/log.txt", statusFile = "/home/user/log/lsyncd/status.txt", maxProcesses = 2, nodaemon = false, } bash = { onStartup = "rsync [email protected]:/home/user/www /home/user/www" } sync{ default.rsyncssh, source="/home/user/www/", host="[email protected]", targetdir="/home/user/www/", rsyncOpts="-ltus", excludeFrom="/home/user/conf/lsyncd/exclude" } (I've obviously redacted that file somewhat to protect the identities of the guilty.) Simply put, though, this just isn't working. How else might I approach this problem? I was looking at the --delete-after option in man rsync, but I don't think that does what I'm looking for. Are there any suggestions about how I should approach this problem? Thanks for lending your time and expertise. Chris

  Read the article

• Emails not being delivered

  - by Tomtiger11

  Comment pointed out that this may fix my problem, and it did: Why don't mails show up in the recipient's mailspool? I use Postfix with Dovecot, and when I send an email from my gmail to my server, it is received at the server, but not at my email client using POP3. I can verify it being received at the server using the mail command. This is my main.cf: queue_directory = /var/spool/postfix command_directory = /usr/sbin daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix mail_owner = postfix myhostname = tom4u.eu myorigin = $myhostname inet_interfaces = all inet_protocols = all unknown_local_recipient_reject_code = 550 relay_domains = $mydomain alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases debug_peer_level = 2 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin ddd $daemon_directory/$process_name $process_id & sleep 5 sendmail_path = /usr/sbin/sendmail.postfix newaliases_path = /usr/bin/newaliases.postfix mailq_path = /usr/bin/mailq.postfix setgid_group = postdrop html_directory = no manpage_directory = /usr/share/man sample_directory = /usr/share/doc/postfix-2.6.6/samples readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES smtpd_tls_cert_file = /etc/postfix/certs/cert.pem milter_protocol = 2 milter_default_action = accept smtpd_milters = inet:localhost:8891 non_smtpd_milters = inet:localhost:8891 smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous smtpd_sasl_local_domain = $myhostname smtpd_recipient_restrictions = reject_non_fqdn_recipient,permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination,permit broken_sasl_auth_clients = yes smtpd_sasl_type = dovecot smtpd_sasl_path = private/auth If you could help me with this, I'd be most grateful, if you need any more information, please ask. var/log/maillog: May 30 22:44:25 tom4u postfix/smtpd[18626]: connect from mail-we0-f181.google.com[74.125.82.181] May 30 22:44:25 tom4u postfix/smtpd[18626]: 318F679B7F: client=mail-we0-f181.google.com[74.125.82.181] May 30 22:44:25 tom4u postfix/cleanup[18631]: 318F679B7F: message-id=<CAA_0zdxY-WUFGOC57K_yVn0G+5hN=8KSXuohJqMDB5Rm7bqu8w@mail.gmail.com> May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: mail-we0-f181.google.com [74.125.82.181] not internal May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: not authenticated May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: DKIM verification successful May 30 22:44:25 tom4u opendkim[15006]: 318F679B7F: s=20120113 d=gmail.com SSL May 30 22:44:25 tom4u postfix/qmgr[16282]: 318F679B7F: from=<[email protected]>, size=1720, nrcpt=1 (queue active) May 30 22:44:25 tom4u postfix/smtpd[18626]: disconnect from mail-we0-f181.google.com[74.125.82.181] May 30 22:44:25 tom4u postfix/local[18632]: 318F679B7F: to=<[email protected]>, relay=local, delay=0.17, delays=0.12/0.01/0/0.03, dsn=2.0.0, status=sent (delivered to mailbox) May 30 22:44:25 tom4u postfix/qmgr[16282]: 318F679B7F: removed May 30 22:45:32 tom4u dovecot: pop3-login: Login: user=<tom>, method=PLAIN, rip=SNIP, lip=176.31.127.165, mpid=18679 May 30 22:45:32 tom4u dovecot: pop3(tom): Disconnected: Logged out top=0/0, retr=0/0, del=0/0, size=0 May 30 22:46:32 tom4u dovecot: pop3-login: Login: user=<tom>, method=PLAIN, rip=SNIP, lip=176.31.127.165, mpid=18725 May 30 22:46:32 tom4u dovecot: pop3(tom): Disconnected: Logged out top=0/0, retr=0/0, del=0/0, size=0

  Read the article

• How to create NTFS partition in Linux to install Windows 7 from USB?

  - by Michal Stefanow

  I messed up with my computer and need help. Generally: install Windows 7 from USB. Problem: "setup was unable to create a new system partition" When first attempt to install Windows 7 failed I tried Linux live USB, installed distro to HDD, and erased all the existing partitions. Current state (fdisk -l): [writing from other computer so no copy and paste] /dev/sda1 305GB Linux /dev/sda2 7GB Extended /dev/sda5 7GB Linux Swam / Solaris To create a new, NTFS partition: fdisk /dev/sda n (for new) p (for primary) 3 (for partintion number) "No free sectors available" All the HDD was formatted couple of minutes before so there is a lot of free space but how to resize a parition? I cannot find an option for resizing in man fdisk. Some people say I should use gparted but my distro doesn't not contain this package. And my distro doesn't support wireless drivers so I have serious problems with downloading stuff. I tried also using cfdisk but any command results in: "cfdisk bad primary partition 1 partition ends in the final partial cylinder" I tried also removing partition 1 and then creating a new one (so there is no "no free sectors"). I'm receiving a warning: "Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot." After restating: "grub rescue, no known filesystem" It may indicate that some changes have been made BUT when running Windows 7 installed some another error: "Windows cannot be installed to Disk 0 Partition 1" More detailed: "Windows cannot be installed to this hard disk space. Windows must be installed to a partition formatted as NTFS." So formatting drive using Windows 7 installer BUT this time yet another error: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information" Apparently I cannot access logs (how?) and I am back to drawing board with my live USB (this time showing partition as HPFS/NTFS). Any suggestions how to install Windows 7? Should I reinstall Linux to HDD, erase existing partitions once again, and use Parted rather than gparted (parted is included in the distro). Or maybe should I create another bootable USB such as PartedMagic to painlessly create partitions? I just want to install Windows 7 from USB, my laptop is semi-operational and I am ready to receive some help regarding fdisk and creating NTFS partitions. UPDATE: I did as suggested (removed all the partitions) and tried to install in unallocated space. Tried to create a new partition and format it. Same error: "setup was unable to create a new system partition" Came to the conclusion it may have something to do with TrueCrypt I have recently installed. Right now trying to FIX MBR (as I haven't got possibility to create rescue disc without optical drive)

  Read the article

• libreadline history lines combine

  - by jettero

  This has been driving me crazy for about three years. I don't know how to fully describe the problem, but I think I can finally describe a way to recreate it. Your milage may vary. I have a mixture of ubuntu server and desktop machines of various versions and a few gentoo machines with various states of disrepair. They all seem to kindof do their own thing, although with similarities. Try this and let me know if you see the same thing. pop open two xterms (TERM=xterm) resize one so they're not the same issue screen -R test1 in one (TERM=screen) and screen -x test1 in the other hooray, typing in one shows up in the other; although notice that their different size produces artifacts and things issue a couple commands in your shell hit ^AF in the one that doesn't fit quite right, now it fits!! scroll back over the history a little goto 6 Eventually you'll notice a couple history lines combine. If you don't, then it's something unique to my setup, which spans various distributions and computers; so that's a confusing concept to me. If you see the thing I'm seeing then this: bash$ ls -al bash$ ps auxfw becomes this: bash$ ls -al; ps auxfw It doesn't happen every time. I have to really play with it — unless I don't want it to happen, then it always does. On some systems (or combinations), I get a line separator like the example above. On some systems, I do not. That I get the line separator on some systems seems to indicate to me that bash supports this behavior. Its history is entirely handled by libreadline and after perusing (ie, carefully reading) the man pages, I couldn't find a single readline setting for combining two history lines. Nor can I find anything in the bash manpage. So, how can I invoke this on purpose? Or, if I can't do that, how can I disable it completely? I would take either answer as a solution. Currently, I only see it when I don't want it.

  Read the article

• XCP Project Kronos syslog error: "irq ... : nobody cared" on Dom0 host

  - by Vlad Fedin

  One of our production clusters driven by XCP suddenly went uresponsive. After restart and some investigation we found such logs in dom0 machine syslog: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659040] irq 339: nobody cared (try booting with the "irqpoll" option) Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659058] Pid: 0, comm: swapper/3 Tainted: G C O 3.2.0-24-generic #37-Ubuntu Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659060] Call Trace: Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659062] <IRQ> [<ffffffff810db37d>] __report_bad_irq+0x3d/0xe0 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659071] [<ffffffff810db605>] note_interrupt+0x135/0x190 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659074] [<ffffffff810d8e69>] handle_irq_event_percpu+0xa9/0x220 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659078] [<ffffffff8130ff3b>] ? radix_tree_lookup+0xb/0x10 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659081] [<ffffffff810d9031>] handle_irq_event+0x51/0x80 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659084] [<ffffffff810dc187>] handle_edge_irq+0x87/0x140 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659089] [<ffffffff813a8829>] __xen_evtchn_do_upcall+0x199/0x250 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659092] [<ffffffff813aa96f>] xen_evtchn_do_upcall+0x2f/0x50 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659096] [<ffffffff81666d3e>] xen_do_hypervisor_callback+0x1e/0x30 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659097] <EOI> [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659104] [<ffffffff810013aa>] ? hypercall_page+0x3aa/0x1000 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659107] [<ffffffff8100a1d0>] ? xen_safe_halt+0x10/0x20 Oct 26 20:32:03 hetzner-2-mrx kernel: [1797931.659110] [<fff IRQ 339 in cat /proc/interrupts: 339: ... xen-pirq-msi-x eth0 where eth0 is hardware NIC. While host machine seems to hang, guest machines continue to work, so our tiny internal monitoring on one of the virtual hosts logged something like that: [2012-10-26 20:31:51] [OK......] 200 OK : 113159149 ns [2012-10-26 20:32:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 47763284432 ns ... [2012-10-26 20:34:40] [DISASTER] 500 Can't connect to [hostname]:80 (No route to host) : 46894835070 ns [2012-10-26 20:34:57] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 16821741955 ns ... [2012-10-26 20:38:18] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 20103298289 ns [2012-10-26 20:38:37] [DISASTER] 500 Can't connect to [hostname]:80 (Bad hostname) : 17895754943 ns Host and guest OS: Ubuntu 12.04 LTS, 05:00.0 Ethernet controller: Intel Corporation 82574L Gigabit Network Connection Subsystem: ASUSTeK Computer Inc. Device 8369 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at fe500000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at e000 [size=32] Region 3: Memory at fe520000 (32-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: e1000e Kernel modules: e1000e Any hints how to debug this?

  Read the article

• script to count the occurence of the particular string in the given time interval

  - by pruthvi

  We are trying to write a script "sendemail.sh" to count the number of occurrence of a particular string in a log file "SendEmail.log" within the given interval. We have a log file. In that we are searching for a pattern "ReqInputMsgLog" and need to count the number of times it occurred in the given period for eg: from "2014-08-19 11:30" to "2014-08-19 11:34". And our script look like this: #!/bin/sh enterdate=$1 echo $enterdate enddate=$2 enterdate1=`date +%s -d $enterdate +"%Y-%m-%d %H:%M"` echo $enterdate1 enddate1=`date +%s -d $enddate +"%Y-%m-%d %H:%M"` echo $enddate count=0 cat SendEmail.log | grep "ReqInputMsgLog" | awk -F "[" '{print $3}' | awk -F "," '{print $1}' > /con/scripts_server/file.txt for line in `cat /con/scripts_server/file.txt` do logdate=`echo $line | awk -F : '{print $1":"$2}'` if [[ $logdate < $enddate1 ]]; then count=`expr $count + 1` fi done echo $count But when we are trying to execute the script by the below command its not showing the proper count. ./sendemail.sh "2014-08-19 11:30" "2014-08-19 11:34" Log file is very big one. Small chunk has been posted here. INFO [SIBJMSRAThreadPool : 5] [2014-08-19 11:18:24,471] SendEmail - 8/19/14 11:18 AM,ECCF25B0-0147-4000-E000-1B830A3C05A9,ReqInputMsgLog,SendEmail,<?xml version="1.0" encoding="UTF-8"?> <in:sendEmailRequestMsg xmlns:in="http://EmailMed/EmailMedInterface" xmlns:ns0="wsdl.http://EmailMed/EmailMedInterface" xmlns:ns1="http://EmailMed/EmailMedInterface" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:me="wsdl.http://EmailMed/EmailMedInterface" xsi:type="me:sendEmailRequestMsg"> <in:sendEmail xmlns:xci0="http://EmailMed/EmailMedInterface"> INFO [SIBJMSRAThreadPool : 7] [2014-08-19 11:18:14,235] SendEmail - 8/19/14 11:18 AM,ECCEFDB2-0147-4000-E000-1B830A3C05A9,ReqInputMsgLog,SendEmail,<?xml version="1.0" encoding="UTF-8"?> <in:sendEmailRequestMsg xmlns:in="http://EmailMed/EmailMedInterface" xmlns:ns0="wsdl.http://EmailMed/EmailMedInterface" xmlns:ns1="http://EmailMed/EmailMedInterface" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:me="wsdl.http://EmailMed/EmailMedInterface" xsi:type="me:sendEmailRequestMsg"> <in:sendEmail xmlns:xci0="http://EmailMed/EmailMedInterface"> INFO [SIBJMSRAThreadPool : 7] [2014-08-19 11:18:14,241] SendEmail - xmlText: <?xml version="1.0" encoding="UTF-8"?> after awk command we will get a file "/con/scripts_server/file.txt" which looks similar like below: 2014-08-19 11:28:03 2014-08-19 11:28:06 2014-08-19 11:28:17 2014-08-19 11:28:53 2014-08-19 11:29:02 2014-08-19 11:29:47 2014-08-19 11:29:57 2014-08-19 11:30:07 2014-08-19 11:30:17 2014-08-19 11:30:19 2014-08-19 11:30:19 2014-08-19 11:30:22 2014-08-19 11:30:25 2014-08-19 11:30:25 2014-08-19 11:30:36 2014-08-19 11:30:51 2014-08-19 11:30:56 2014-08-19 11:30:59 2014-08-19 11:30:59 2014-08-19 11:31:08 2014-08-19 11:31:25 2014-08-19 11:32:19 2014-08-19 11:32:22 2014-08-19 11:32:27 2014-08-19 11:32:28 2014-08-19 11:32:41 2014-08-19 11:32:49 2014-08-19 11:32:59 2014-08-19 11:33:27 2014-08-19 11:33:41 2014-08-19 11:34:07 2014-08-19 11:34:14 2014-08-19 11:34:21 2014-08-19 11:34:25 2014-08-19 11:34:38 2014-08-19 11:34:50 2014-08-19 11:34:58

  Read the article

• inews failed: "No colon-space in "X-MS-TNEF-Correlator:"

  - by wolfgangsz

  We run a news server for our engineering teams, which is also linked to the code repositories (so that all engineers can subscribe to any changes in the repos or just the projects they are interested in). On quite a regular basis (several times a day) I (as the sysadmin for that server) receive bounces from innd with the above as the first line. The news server simply rejects these messages and the articles don't get posted. Here is an example: inews failed: inews: cannot send article to server: 441 437 No colon-space in "X-MS-TNEF-Correlator:" header inews: article not posted -------- Article Contents Path: aminocom.com!ctaylor From: [email protected] (Cameron Taylor) Newsgroups: amino.qa.reports Content-Language: en-US Content-Type: multipart/alternative; boundary="_000_A2AB95742ADD524795C13EDE8F8CCD201A798C0Eukswaex01_" MIME-Version: 1.0 Subject: [QA REPORT] MDK 400 release 3.4.33 **PRE-RELEASE** Message-ID: Date: Thu, 9 Sep 2010 16:15:16 +0000 X-Received: from uk-swa-ex02.aminocom.com (uk-swa-ex02.aminocom.com [10.171.3.10]) by theoline.aminocom.com (8.14.3/8.13.8) with ESMTP id o89GF8tx019494 for ; Thu, 9 Sep 2010 17:15:08 +0100 X-Received: from uk-swa-ex01.aminocom.com ([10.171.3.9]) by uk-swa-ex02 ([10.171.3.10]) with mapi; Thu, 9 Sep 2010 17:15:18 +0100 X-To: QA Reports X-Thread-Topic: [QA REPORT] MDK 400 release 3.4.33 **PRE-RELEASE** X-Thread-Index: ActQOjBdms0CSJsORNSxRIMSZ4H3Ow== X-Accept-Language: en-US, en-GB X-MS-Has-Attach: X-MS-TNEF-Correlator: X-Auto-Response-Suppress: DR, OOF, AutoReply --_000_A2AB95742ADD524795C13EDE8F8CCD201A798C0Eukswaex01_ Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: quoted-printable SQA Test Report [QA REPORT] MDK 400 release 3.4.33 **PRE-RELEASE** Status .... (rest of the message is not important) And yes, quite clearly this header doesn't have anything after the colon. The man page for innd doesn't specify why it rejects these messages, it just says it rejects them. So far I have found out these headers are linked to messages in RTF format (coming from Outlook clients), where normally the formatting information would be stored in a winmail.dat attachment. The clients all use MS Exchange 2010 servers to send their mail (identified above as uk-swa-ex02.aminocom.com) which forwards the message to the news server. Does anybody know what advice I need to give these users to avoid their articles getting bounced? Or can I change the behaviour of innd? Or do I need to filter these headers out before innd processes the articles?

  Read the article

• How can I fix Problems with interlaced video jerking/flicking when playedback on DVD players? (Mixin

  - by Simon P Stevens

  I'm trying to make a DVD and the final DVD jerks when played on standalone DVD players. It seems to play fine on PCs. I think the problem may be to do with interlacing settings when rendering the final output, but I'll outline the whole editing process I have followed in case I've made a mistake somewhere else. Most of the footage comes from a sony handy cam (one of those mini DVD ones) so isn't great quality. It was set to "high quality" (haha) and 16:9 aspect ratio when it was recorded. I copy the files directly from the mini DVDs onto the hard drive and import them into Cinelerra. In Cinelerra I set the format to 25fps, 720x576, RGBA-8bit, 16:9, interlaced bottom fields first. When I've finished the editing, I add a Fields to frames effect (set to bottom first) to each video track. I render to audio and video separately: Audio: AC3, 128kbps Video: YUV4MPEG steam, video pipe settings: ffmpeg -f yuv4mpegpipe -i - -y -target dvd -flags +ilme+ildct mpeg2video % Cinelerra often crashes during the rendering, so I set it to generate a new video file at each label, and combine them using cat when I've got a sucesful render of each one. Once I've combined them, I use mencoder to re-index them: mencoder -forceidx -oac copy -ovc copy merged.m2v -o mergedReIndexed.m2v I combine the audio and video files using ffmpeg: ffmpeg -i AudioFile.ac3 -i VideoFile.m2v -target dvd -flags +ilme+ildct FinalMovie.mpg Then I build the menus with spumux and I create the DVD file system with dvdauthor, and finally I write it do a dvd-r like this: nice -n -20 growisofs -dvd-compat -speed=2 -Z /dev/dvd -dvd-video -V VIDEO ./ && eject /dev/dvd Originally, when I did it the DVD flickered badly, so as suggested in a guide I added the fields to frames effect in cinelerra. Now it doesn't "flicker", but has become "jerky" when there is lots of motion, particularly when the camera is moving, so the whole background moves. This is what I've tried so far: Removed "mpeg2video" from cinelerra video render pipe. Removed +ilme from render pipe. Removed +ildct from render pipe. Removed +ilme from render audio/video rejoin command. Removed +ildct from render audio/video rejoin command. Added -alt to render pipe. Added -alt to render audio/video rejoin command. Tried with and without the frames to fields effect in Cinelerra. and various combinations of the above. I've also tried this: change the Cinelerra fps to 50, use fields to frames (instead of frames to fields), render to an intermediate QTforlinux jpeg video stream, re-importing that back into Cinelerra, adding a frames to fields effect and then rendering that output as normal (@25fps), and I still have the same problem. Has anyone experienced this "jerking" playback before? Can anyone give any suggestions on how to fix it? (Like I say, it plays back fine on a PC, but not on any of the standalone players I've tried)

  Read the article

• Ubuntu and Postfix Configuration Issues

  - by Obi Hill

  I recently installed postfix on Ubuntu Natty. I'm having a problem with the configuration. Firstly here is my postfix configuration file: # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. mydomain = $myorigin myhostname = mail.nairanode.com alias_maps = hash:/etc/postfix/aliases alias_database = hash:/etc/postfix/aliases # this specifies where the virtual mailbox folders will be located virtual_mailbox_base = /var/spool/mail/virtual # this specifies where the virtual mailbox folders will be located virtual_mailbox_base = /var/spool/mail/virtual # this is for the mailbox location for each user virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf # and this is for aliases virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf # and this is for domain lookups virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf # this is how to connect to the domains (all virtual, but the option is there) # not used yet # transport_maps = mysql:/etc/postfix/mysql_transport.cf virtual_uid_maps = static:5000 virtual_gid_maps = static:5000 mydestination = $myorigin, $myhostname, localhost.localdomain, , localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all #mynetworks_style = host # ADDITIONAL unknown_local_recipient_reject_code = 550 maximal_queue_lifetime = 7d minimal_backoff_time = 1000s maximal_backoff_time = 8000s smtp_helo_timeout = 60s smtpd_recipient_limit = 16 smtpd_soft_error_limit = 3 smtpd_hard_error_limit = 12 # Requirements for the HELO statement smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit # Requirements for the sender details smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_$ # Requirements for the connecting server smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.n$ # Requirement for the recipient address smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_do$ # require proper helo at connections smtpd_helo_required = yes # waste spammers time before rejecting them smtpd_delay_reject = yes disable_vrfy_command = yes Here is also my /etc/postfix/aliases: # See man 5 aliases for format postmaster: root Here is also my /etc/mailname: nairanode.com I've also updated my hostname to nairanode.com However, when I run postalias /etc/postfix/aliases I get the following : postalias: warning: valid_hostname: invalid character 47(decimal): /etc/mailname postalias: fatal: file /etc/postfix/main.cf: parameter mydomain: bad parameter value: /etc/mailname Is there something I'm doing wrong?! I noticed that when I replace myorigin = /etc/mailname with myorigin = nairanode.com in my postfix config, I don't see any errors anymore after calling postalias. Is this a bug or something?!

  Read the article

• Postfix issues sending mail to addresses under domain located on server

  - by iamthewit

  I recently installed virtualmin on my nice shiny new rackspace cloud. Everything went seemlessly but I've been having some issues getting emails to send properly. The problem seems to be that the server can not send mail to email addresses where the domain is owned by my server. For example, on my server I run multiple virtual domains, lets call this one test.com. When I run the mail command from shell (mail [email protected]) I get the following back from my maillog: Oct 6 14:55:18 test postfix/pickup[8737]: DC1131612CC: uid=0 from= Oct 6 14:55:18 test postfix/cleanup[8769]: DC1131612CC: [email protected] Oct 6 14:55:18 test postfix/qmgr[8738]: DC1131612CC: [email protected], size=353, nrcpt=1 (queue active) Oct 6 14:55:18 test postfix/error[8771]: DC1131612CC: [email protected], relay=none, delay=0, delays=0/0/0/0, dsn=5.0.0, status=bounced (User unknown in virtual alias table) Oct 6 14:55:18 test postfix/cleanup[8769]: DD07D1612D1: [email protected] Oct 6 14:55:18 test postfix/bounce[8772]: DC1131612CC: sender non-delivery notification: DD07D1612D1 Oct 6 14:55:18 test postfix/qmgr[8738]: DD07D1612D1: from=<, size=2268, nrcpt=1 (queue active) Oct 6 14:55:18 test postfix/qmgr[8738]: DC1131612CC: removed Oct 6 14:55:18 test postfix/local[8773]: DD07D1612D1: [email protected], relay=local, delay=0.03, delays=0/0/0/0.03, dsn=2.0.0, status=sent (delivered to command: /usr/bin/procmail-wrapper -o -a $DOMAIN -d $LOGNAME) Oct 6 14:55:18 test postfix/qmgr[8738]: DD07D1612D1: removed when I run mail [email protected] the message is sent and received perfectly fine. I'm a bit of a noob when it comes to servers, but I pick things up fairly quickly, so please excuse any incorrect terminology and my general noobiness. Any help would be greatly appreciated, I've been googling for quite a while but I haven't found a solution yet, I'll add a copy of my main.cf file in a response below cheers guys here is the reformatted postconf, do you want the reformatted main.cf file too, or is this enough? alias_database = hash:/etc/postfix/aliases alias_maps = hash:/etc/postfix/aliases broken_sasl_auth_clients = yes command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix debug_peer_level = 2 home_mailbox = Maildir/ html_directory = no mailbox_command = /usr/bin/procmail-wrapper -o -a $DOMAIN -d $LOGNAME mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man myhostname = server.test.com newaliases_path = /usr/bin/newaliases.postfix readme_directory = /usr/share/doc/postfix-2.3.3/README_FILES sample_directory = /usr/share/doc/postfix-2.3.3/samples sender_bcc_maps = hash:/etc/postfix/bcc sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtpd_recipient_restrictions = permit_mynetworks permit_sasl_authenticated reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous unknown_local_recipient_reject_code = 550 virtual_alias_maps = hash:/etc/postfix/virtual

  Read the article

• How to tune system settings for mongoDB on Linux?

  - by jsh

  Trying to squeeze a lot out of one question here -- please bear with me. Although the MongoDB man pages make several useful recommendations about system settings like ulimit (http://docs.mongodb.org/manual/reference/ulimit/), and other production factors (http://docs.mongodb.org/manual/administration/production-notes/) they seem mysteriously silent on things like virtual memory and swap settings. The closest we get to a hint is that "...the operating system’s virtual memory subsystem manages MongoDB’s memory..." (http://docs.mongodb.org/manual/faq/fundamentals/#does-mongodb-require-a-lot-of-ram). Running the same job - high writes and high reads on about 10,000,000 records in a single collection -- on my 4-processor, 4GB RAM macbook and an 8-core ubuntu box with 64GB RAM I saw dramatically WORSE read performance on the linux box with factory settings, and could hear the disk constantly spinning, indicating high I/O and presumably swapping. Yes, other things were happening on the box, but there was plenty of free RAM, disk space, etc.; furthermore, I did not see evidence that Mongo was expanding to take advantage of all that free RAM as it is touted to do. Linux box default settings were as follows: vm.swappiness =60 vm.dirty_background_ratio = 10 vm.dirty_ratio = 20 vm.dirty_expire_centisecs =3000 vm.dirty_writeback_centisecs=500 I hazarded some guesses looking at docs and blogs for other types of databases (Oracle, MYSQL, etc.), experimented, and adjusted as below. vm.swappiness=10 vm.dirty_background_ratio=5 vm.dirty_ratio=5 vm.dirty_writeback_centisecs=250 vm.dirty_expire_centisecs=500 I saw some immediate apparent improvements in read time. However, when I ran my test jobs again, read performance continued to be painfully sluggish during heavy writes. Then, I REBUILT the collection from an available data source - and suddenly I can read at 1ms or less per record WHILE doing the write job! So the question is really two-fold: 1) What are appropriate VM settings for MongoDB on Linux? 2) (bonus) Does Mongo do some checking or optimization with the OS while data is being built? In other words, if I have built a large data set with suboptimal VM or I/O settings, does Mongo make assumptions during the memory-mapping process that will fail to take advantage of optimizations down the road? Obviously I don't fully grok memory mapping under the hood (I was hoping I wouldn't have to). Any help appreciated...thanks! -j

  Read the article

• How to disable or tune filesystem cache sharing for OpenVZ?

  - by gertvdijk

  For OpenVZ, an example of container-based virtualization, it seems that host and all guests are sharing the filesystem cache. This sounds paradoxical when talking about virtualization, but this is actually a feature of OpenVZ. It makes sense too. Because only one kernel is running, it's possible to benefit from sharing the same pages of filesystem cache in memory. And while it sounds beneficial, I think a set up here actually suffers in performance from it. Here's why I think why: my machines aren't actually sharing any files on disk so I can't benefit from this feature in OpenVZ. Several OpenVZ machines are running MySQL with MyISAM tables. MyISAM relies on the system's filesystem cache for caching of data files, unlike InnoDB's buffer pool. Also some virtual machines are known to do heavy and large I/O operations on the same filesystem in the host. For example, when running cat *.MYD > /dev/null on some large database in one machine, I saw the filesystem cache lowering in another, monitored by htop. This essentially flushes all the useful filesystem cache in guests (FIFO) and so it flushes the MySQL caches in the guests. Now users are complaining that MySQL is very slow. And it is. Some simple SELECT queries take several seconds on times disk I/O is heavily used by other machines. So, simply put: Is there a way to avoid filesystem cache being wiped out by other virtual machines in container-based virtualization? Some thoughts: Choosing algorithm for flushing filesystem cache in the kernel. (possible? how?) Reserving a certain amount of pages for a single VM. (seems no option for filesystem cache type of pages that reading man vzctl) Will running MySQL on another filesystem get me anywhere? If not, I think my alternatives are: Use KVM for MySQL-MyISAM running VMs. KVM actually assigns memory to the VM and does not allow swapping out caches unless using a balloon driver. Move to InnoDB and tune the buffer pools, dirty pages, etc. This is now considered to be 'nice to have' on the long-term as not everyone responsible for administration of the system understands InnoDB. more suggestions welcome. System software: Proxmox (now 1.9, could be upgraded to 2.x). One big LV assigned for the VMs.

  Read the article

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• Puppet and launchd services?

  - by Joel Westberg

  We have a production environment configured with Puppet, and want to be able to set up a similar environment on our development machines: a mix of Red Hats, Ubuntus and OSX. As might be expected, OSX is the odd man out here, and sadly, I'm having a lot of trouble with getting this to work. My first attempt was using macports, using the following declaration: package { 'rabbitmq-server': ensure => installed, provider => macports, } but this, sadly, generates the following error: Error: /Stage[main]/Rabbitmq/Package[rabbitmq-server]: Could not evaluate: Execution of '/opt/local/bin/port -q installed rabbitmq-server' returned 1: usage: cut -b list [-n] [file ...] cut -c list [file ...] cut -f list [-s] [-d delim] [file ...] while executing "exec dscl -q . -read /Users/$env(SUDO_USER) NFSHomeDirectory | cut -d ' ' -f 2" (procedure "mportinit" line 95) invoked from within "mportinit ui_options global_options global_variations" Next up, I figured I'd give homebrew a try. There is no package provider available by default, but puppet-homebrew seemed promising. Here, I got much farther, and actually managed to get the install to work. package { 'rabbitmq': ensure => installed, provider => brew, } file { "plist": path => "/Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist", source => "/usr/local/opt/rabbitmq/homebrew.mxcl.rabbitmq.plist", ensure => present, owner => root, group => wheel, mode => 0644, } service { "homebrew.mxcl.rabbitmq": enable => true, ensure => running, provider => "launchd", require => [ File["/Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist"] ], } Here, I don't get any error. But RabbitMQ doesn't start either (as it does if I do a manual load with launchctl) [... snip ...] Debug: Executing '/bin/launchctl list' Debug: Executing '/usr/bin/plutil -convert xml1 -o /dev/stdout /Library/LaunchDaemons/homebrew.mxcl.rabbitmq.plist' Debug: Executing '/usr/bin/plutil -convert xml1 -o /dev/stdout /var/db/launchd.db/com.apple.launchd/overrides.plist' Debug: /Schedule[weekly]: Skipping device resources because running on a host Debug: /Schedule[puppet]: Skipping device resources because running on a host Debug: Finishing transaction 2248294820 Debug: Storing state Debug: Stored state in 0.01 seconds Finished catalog run in 25.90 seconds What am I doing wrong?

  Read the article

• a couple of questions about proxy server,vpn & how they works

  - by Q8Y

  I have a couple of questions that are related to security. Correct me if i'm wrong :) If I want to request something (ex: visiting www.google.com): my computer will request that then it will to the ISP then to my ISP proxy server that will take the request and act as a middle man in this situation ask for the site (www.google.com) and retrieve it then the proxy will send it back to me. I know that its being done like that. So, my question is that, in this situation my ISP knows everything and what I did request, and the proxy server is set by default (when I ask for an internet subscription). So, if I use here another proxy (lets assume that is a highly anonymous and my ISP can't detect my IP address from it), would I visit my ISP and then from my ISP it will redirect me to the new proxy server that I provide? Will it know that there is someone using another proxy? Or will it go to another network rather than my ISP? Because I didn't get the view clearly. This question is related to the first one. When I use a VPN, I know that VPN provides for me a tunneling, encryption and much more features that a proxy can't. So my data is travelling securely and my ISP can't know what I'm doing. But my questions are: From where is the tunneling started? Does it start after I visit the ISP network (since they are the one that are responsible for forwarding my data and requests)? If so, then not all my connection is tunneled in this way, there is a part that is not being tunneled. Since, every time I need to do anything I have to go to my ISP and ask to do that. Correct me if I misunderstand this. I know that VPN can let my computer be virtually in another place and access its resources (ex: be like in my office while I'm in my home. This is done via VPN). If I use a VPN service provider so that I can access the internet securely and without being monitored by my ISP. In this case, where is my encrypted data saved? Is it saved in my ISP or in the VPN service provider? If I use a VPN, does anyone on the internet know what I'm doing or who I am? Even the VPN service provider? Can they know me? I think they should know the person that is asking for this VPN service, am I right?

  Read the article

• Why do I sometimes get 'sh: $'\302\211 ... ': command not found' in xterm/sh?

  - by amn

  Sometimes when I simply type a valid command like 'find ...', or anything really, I get back the following, which is completely unexpected and confusing (... is command name I type): sh: $'\302\211...': command not found There is some corruption going on I think. I don't use color in my prompt, I am using the Bash shell in POSIX mode as sh (chsh to /bin/sh and so on - $SHELL is sh). What is going on and why does this keep happening? Anything I can debug? I think this is more of an xterm issue than sh, or at least a combination of the two. Files, for context: My /etc/profile, as distributed with Arch Linux x86-64: # /etc/profile #Set our umask umask 022 # Set our default path PATH="/usr/local/sbin:/usr/local/bin:/usr/bin" export PATH # Load profiles from /etc/profile.d if test -d /etc/profile.d/; then for profile in /etc/profile.d/*.sh; do test -r "$profile" && . "$profile" done unset profile fi # Source global bash config if test "$PS1" && test "$BASH" && test -r /etc/bash.bashrc; then . /etc/bash.bashrc fi # Termcap is outdated, old, and crusty, kill it. unset TERMCAP # Man is much better than us at figuring this out unset MANPATH My /etc/shrc, which I created as a way to have sh parse some file on startup, when non-login shell. This is achieved using ENV variable set in /etc/environment with the line ENV=/etc/shrc: PS1='\u@\H \w \$ ' alias ls='ls -F --color' alias grep='grep -i --color' [ -f ~/.shrc ] && . ~/.shrc My ~/.profile, I am launching X when logging in through first virtual tty: [[ -z $DISPLAY && $XDG_VTNR -eq 1 ]] && exec xinit -- -dpi 111 My ~/.xinitc, as you can see I am using the system as a Virtual Box guest: xrdb -merge ~/.Xresources VBoxClient-all awesome & exec xterm And finally, my ~/.Xresources, no fancy stuff here I guess: *faceName: Inconsolata *faceSize: 10 xterm*VT100*translations: #override <Btn1Up>: select-end(PRIMARY, CLIPBOARD, CUT_BUFFER0) xterm*colorBDMode: true xterm*colorBD: #ff8000 xterm*cursorColor: S_red Since ~/.profile references among other things /etc/bash.bashrc, here is its content: # # /etc/bash.bashrc # # If not running interactively, don't do anything [[ $- != *i* ]] && return PS1='[\u@\h \W]\$ ' PS2='> ' PS3='> ' PS4='+ ' case ${TERM} in xterm*|rxvt*|Eterm|aterm|kterm|gnome*) PROMPT_COMMAND=${PROMPT_COMMAND:+$PROMPT_COMMAND; }'printf "\033]0;%s@%s:%s\007" "${USER}" "${HOSTNAME%%.*}" "${PWD/#$HOME/~}"' ;; screen) PROMPT_COMMAND=${PROMPT_COMMAND:+$PROMPT_COMMAND; }'printf "\033_%s@%s:%s\033\\" "${USER}" "${HOSTNAME%%.*}" "${PWD/#$HOME/~}"' ;; esac [ -r /usr/share/bash-completion/bash_completion ] && . /usr/share/bash-completion/bash_completion I have no idea what that case statement does, by the way, it does look a bit suspicious though, but then again, who am I to know.

  Read the article

• Can only bring up one of two interfaces

  - by mstaessen

  I'm having a bizarre issue with my HP Proliant DL 360 G4p server. It has two gigabit ethernet interfaces but I can bring up only one of them. This is starting to freak me out and that's why I turned here. I'm running the x64 ubuntu 11.10 server edition. lshw -c network shows that the second interface is disabled. I have no idea why ans how to enable it. $ sudo lshw -c network *-network:0 description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 logical name: eth0 version: 10 serial: 00:18:71:e3:6d:26 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=5704-v3.27b, ASFIPMIc v2.36 ip=10.48.8.x latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:25 memory:fdf70000-fdf7ffff *-network:1 DISABLED description: Ethernet interface product: NetXtreme BCM5704 Gigabit Ethernet vendor: Broadcom Corporation physical id: 2.1 bus info: pci@0000:02:02.1 logical name: eth1 version: 10 serial: 00:18:71:e3:6d:25 capacity: 1Gbit/s width: 64 bits clock: 66MHz capabilities: pcix pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=5704-v3.27b latency=64 link=no mingnt=64 multicast=yes port=twisted pair resources: irq:26 memory:fdf60000-fdf6ffff If I try to ifup eth1, then I get $ sudo ifup eth1 Ignoring unknown interface eth1=eth1. I figured that's what happens when there is no eth1 listed in /etc/network/interfaces. But when I add the configuration for eth1, I still can't ifup. $ sudo ifup eth1 RTNETLINK answers: File exists Failed to bring up eth1. I've also tried ifconfig eth1 up but without any result. For clarity, I have added a masked version of /etc/network/interfaces. I don't think it is the cause of the problem though. $ cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.48.8.x netmask 255.255.255.y network 10.48.8.z broadcast 10.48.8.t gateway 10.48.8.u auto eth1 iface eth1 inet static address 193.190.253.x netmask 255.255.255.y network 193.190.253.z broadcast 193.190.253.t gateway 193.190.253.u I really need some help fixing this. It's driving me crazy. Thanks.

  Read the article

• joining text files with 600M+ lines

  - by dnkb

  I have two files huge.txt and small.txt. Huge has around 600M rows and it's 14Gigs, each line has four space separated words (tokens) and finally another space separated column with a number. Small has 150K rows with a size of ~3M, a space separated word and a number. Both Files are sorted using the sort command, with no extra options. The words in both files may include apostrophes (') and dashes (-). The deisred output would contain all columns from the huge.txt and the second column (the number) from small txt where the first word of huge.txt and the first word of small.txt match. My attemtpts below failed miserably with the following error: cat huge.txt|join -o 1.1 1.2 1.3 1.4 2.2 - small.txt > output.txt join: memory exhausted What I suspect is that the sorting order isn't right somehow even though the files are pre-sorted using: sort -k1 huge.unsorted.txt > huge.txt sort -k1 small.unsorted.txt > small.txt Problems seem to appear around words that have apostrophes (') or dashes (-). I also tried dictinoary sorting using the -d option bumping into the same error at the end. I see two ways out of this but don't know how to implement any of them. 1) Any tips how to sort the files in a way that the join command considers them to be sorted properly? 2) I was thinking of calculating MD5 or some other hashes of the strings to get rid of the apostrophes and dashes, and do the sorting and joining with the hashes instead of the strings themselves an dat the "translate" back the hashes to strings, but leave the numbers intact at the end of the lines. Since there would be only 150K hashes it's not that bad. What would be a good way to calculate individual hashes for each of the strings? Some AWK magic? See file samples at the end. Thank you! sample of huge.txt had stirred me to 46 had stirred my corruption 57 had stirred old emotions 55 had stirred something in 69 had stirred something within 40 sample of small.txt caley 114881 calf 2757974 calfed 137861 calfee 71143 calflora 154624 calfskin 148347 calgary 9416465 calgon's 94846

  Read the article

• SIGINT and SIGTSTP ignored by most common applications

  - by Vašek Potocek

  After the last upgrade to my Fedora, a strange behaviour started occurring in X terminal applications. I can't seem to stop any process using Ctrl+C, it just results in printing ^C to the console. Similarly, Ctrl+Z prints ^Z and the process goes on. Both work well in non-graphical virtual consoles. I checked stty -a and it seems perfectly normal: speed 38400 baud; rows 24; columns 80; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = M-^?; eol2 = M-^?; swtch = M-^?; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 0; -parenb -parodd cs8 hupcl -cstopb cread -clocal -crtscts -ignbrk brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon -ixoff -iuclc ixany imaxbel iutf8 opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt echoctl echoke This is independent of the terminal (gnome-terminal, XFCE4 terminal, xterm). I later noticed that it may not be caused by the terminal at all: INT or TSTP sent directly to the respective process are ignored, too. This comprises various applications I used to terminate using Ctrl+C on a regular basis (and which often don't have any better means of exiting): cat, find, tail -f, java, ping, mplayer when stuck on a broken file... Even bash ignores Ctrl+C when I want to break a command line I have been entering and then changed my mind (no ^C is printed in this case). I need to delete it character by character (of which there may be hundreds if filename completion has been used) or intentionally run the unwanted command. Strangely enough, vim does recognize Ctrl+C—just to say its "use :quit", of course. This is extremely annoying and prevents me from working efficiently. Everything had been working until lately, maybe a week ago or so. I can not find any possible causes in Google, perhaps I'm trying wrong search terms or misidentifying the main problem. What could be it and how could I revert the standard behaviour, please? Update Ctrl+Z works sometimes. It seems that in the very first terminal I launch after logging in it stops the running command but stops working after that.

  Read the article

• MySQL won't start, reinstall fails on Ubuntu 12.04

  - by Evils

  My problem started yesterday night when I tried to change the my.cnf config on my ubuntu 12.04 x64 System. I simply tried to changed the bind-address parameter from 127.0.0.1 to 0.0.0.0. A simple restart after a reboot gave this error: stop: Unknown instance: start: Job failed to start I tried to start mysql then by using 'mysqld' which outputs this: 130701 11:05:59 [Note] Plugin 'FEDERATED' is disabled. mysqld: Table 'mysql.plugin' doesn't exist 130701 11:05:59 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 130701 11:05:59 InnoDB: The InnoDB memory heap is disabled 130701 11:05:59 InnoDB: Mutexes and rw_locks use GCC atomic builtins 130701 11:05:59 InnoDB: Compressed tables use zlib 1.2.3.4 130701 11:05:59 InnoDB: Initializing buffer pool, size = 128.0M 130701 11:05:59 InnoDB: Completed initialization of buffer pool 130701 11:05:59 InnoDB: highest supported file format is Barracuda. 130701 11:05:59 InnoDB: Waiting for the background threads to start 130701 11:06:00 InnoDB: 5.5.31 started; log sequence number 1595675 130701 11:06:00 [Note] Server hostname (bind-address): '127.0.0.1'; port: 3306 130701 11:06:00 [Note] - '127.0.0.1' resolves to '127.0.0.1'; 130701 11:06:00 [Note] Server socket created on IP: '127.0.0.1'. 130701 11:06:00 [ERROR] Can't start server : Bind on unix socket: Permission denied 130701 11:06:00 [ERROR] Do you already have another mysqld server running on socket: /var/run/mysqld/mysqld.sock ? 130701 11:06:00 [ERROR] Aborting 130701 11:06:00 InnoDB: Starting shutdown... 130701 11:06:00 InnoDB: Shutdown completed; log sequence number 1595675 130701 11:06:00 [Note] mysqld: Shutdown complete Meanwhile I already tried to reinstall and purge the complete mysql package which results in another error which says that dpkg cant change the admins password. While this error appeared another error came with it. When trying to install something new with apt, it always says 'fopen: permission denied' right after it tries to update my man-db. This is my dmesg output: [ 6879.687998] type=1400 audit(1372669683.397:36): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/mysqld" pid=9336 comm="apparmor_parser" [ 6881.323215] init: mysql main process (9340) terminated with status 1 [ 6881.323316] init: mysql respawning too fast, stopped Any help will be appreciated as this is a productive server which renders useless without mysql.

  Read the article

• Hyper-V Ubuntu Networking Problems Copying Large Amounts of Data

  - by Anonymous

  I am trying to copy a large amount (about 50 GB) of data over my network from a Hyper-V-hosted virtual machine running Ubuntu 11.04 (Natty Narwhal) to another (non-virtual) Ubuntu host that I plan to use for testing upgrades to one of our web applications. The problem I am having is with the virtual machine, which I shall refer to in what follows as "source.host". This machine is running 64-bit Ubuntu Server with the 2.6.38-8-server kernel and the Microsoft Linux Integration Components for Hyper-V kernel modules (hv_utils, hv_timesource, hv_netvsc, hv_blkvsc, hv_storvsc, and hv_vmbus) loaded. It uses a Hyper-V "synthetic network adapter" for its networking interface. To do the copy, I log on to the machine with the data and run the following commands (Call the remote machine "destination.host".): $ cd /path/to/data $ tar -cvf - datafolder/ | ssh [email protected] "cat > ~/data.tar" This runs for a while and then suddenly stops after transferring somewhere from 2-6 GB. The terminal on the source.host machine displays a Write failed: broken pipe error. The odd part is this: after this occurs, the "source.host" machine is no longer able to talk to the rest of the network. I cannot ping any other hosts on the network from the "source.host" machine, and I cannot ping the "source.host" machine from any other host on the network. I am equally unable to access the any of the web services hosted on "source.host". Running ifconfig on "source.host" shows the network adapter to be up and running as usual with the correct IP address and everything. I tried restarting the networking service with $ /etc/init.d/networking restart but the problem does not go away. Restarting the machine makes it capable of talking to the network again -- it can ping and be pinged by other hosts, and the web services are also accessible and usable as normal -- but attempting the copy operation again results in the same failure, requiring another restart. As an experiment, I tried replacing the tar -- ssh pipeline above with a straight scp: $ scp -r datafolder/ [email protected]:~ but to no avail Thinking that the issue might have to do with the kernel packet-send buffers filling up, I tried increasing the buffer size to 12 MB (up from the 128 KB default) with # echo 12582911 > /proc/sys/net/core/wmem_max but this also had no effect. I'm guessing at this point that it might be a problem with the Microsoft synthetic network driver, but I don't really know. Does anyone have any suggestions? Thank you very much in advance!

  Read the article

• Can not get sound over hdmi in kubuntu 9.10

  - by user32509

  I have used a hdmi cable to connect my lcd (which is connected with my speakers) with my nvida 275 gtx grafic card. I can not get the sound output to work. The hardware itself is working probably - I tested it under windows. Currently I am running Kubuntu 9.10 64 with Nvidia 190.53. The sound output worked fine before I installed the hdmi connection. (German output - i can change it, if you tell me how :)) aplay -l **** Liste von PLAYBACK Geräten **** Karte 0: Intel [HDA Intel], Gerät 0: ALC889A Analog [ALC889A Analog] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 Karte 0: Intel [HDA Intel], Gerät 1: ALC889A Digital [ALC889A Digital] Untergeordnete Geräte: 1/1 Untergeordnetes Gerät '0: subdevice #0 aplay -L front:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog Front speakers surround40:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=Intel,DEV=0 HDA Intel, ALC889A Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers iec958:CARD=Intel,DEV=0 HDA Intel, ALC889A Digital IEC958 (S/PDIF) Digital Audio Output null Discard all samples (playback) or generate zero samples (capture) pulse Playback/recording through the PulseAudio sound server And i disabled mute in kmix an all channels :) Edit: lspci -v ... 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) Subsystem: Giga-byte Technology Device a022 Flags: bus master, fast devsel, latency 0, IRQ 22 Memory at ea400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel <?> Capabilities: [130] Root Complex Link <?> Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel ... cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.20. lsmod | grep snd_hda_intel snd_hda_intel 31880 2 snd_hda_codec 87584 2 snd_hda_codec_realtek,snd_hda_intel snd_pcm 93160 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd 77096 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device snd_page_alloc 10928 2 snd_hda_intel,snd_pcm I think I am missing the something-hdmi module? Is there such a thing?

  Read the article

< Previous Page | 144 145 146 147 148 149 150 151 152 153 154 155  | Next Page >