Search Results

Search found 4763 results on 191 pages for 'policy administration'.

Page 151/191 | < Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >

• How can adding a server to a domain cause Remote Desktop to stop working?

  - by Adrian Grigore

  I have two dedicated with Windows 2008 R2 servers which I am using for Web hosting. One Server A is a domain controller, Server B should simply be added to the domain controlled by Server A. So I RDP'd into Server B and changed the system settings so that Server B is part of that domain. I entered my domain admin credentials, was welcomed to the domain and asked to reboot the server. So far everything seemed to work smoothly After rebooting, I could not open an RDP connection to Server B anymore: Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Make sure the remote computer is turned on and connected to the network, and that remote access is enabled. I restored an older backup of Server B and switched off the firewall before adding the server to my domain. But the problem reoccurred just the same. What could be the reason for this? The domain is brandnew and I did not change any of the default settings. Could this be some kind of domain-wide default policy that shuts down RDP on any domain clients? Or perhaps it has to do with the fact that Server B is virtual? Thanks for your help, Adrian

  Read the article

• Easy GUI way to auto scale EC2 and RDS: aws console, scalr, ylastic...?

  - by Zillo

  I am managing all my instances with the AWS Management Console (the GUI web console) but now I want to use Auto Scale and it seems that this can not be done with that console. Yes, there is CloudWatch but I can only create alarms (e-mail notifications), it seems that CouldWatch needs you to add the auto scale policy in some other place (by command line console?). I would like to use some easy GUI interface. Ylastic and Scalr seems to be a good option. Which one do you think is better? Regarding Scalr, is there any difference between the open source software Scalr and the service Scalr.net? I mean, is the GUI interface the same? I like the idea of the Scalr because I do not need to give my Secret Access Key to a third party (like in Ylastic or in Scalr.net) One question about the Scalr software, it has to be installed in the instances or it must be installed in another machine? Do I need to setup again all my security permissions, AMIs, snapshots, etc. or I can use AWS Management Console for everything and Scalr just to auto scale.

  Read the article

• CryptSvc not matched by Windows 7 Firewall rule

  - by theultramage

  I am using Windows Firewall in conjunction with a third-party tool to get notified about new outbound connection attempts (Windows Firewall Notifier or Windows Firewall Control). The way these tools do it is by setting the firewall to deny by default, and to add an auditing policy to log blocked connections into the Security event log. Then they watch the log, and display notification about newly added entries. netsh advfirewall set allprofiles firewallpolicy blockinbound,blockoutbound auditpol /set /subcategory:{0CCE9226-69AE-11D9-BED3-505054503030} /failure:enable With this configuration in place, I now need to craft outbound allow rules for applications and system services. Here is the rule for CryptSvc, the service frequently used for certificate validation and revocation checking: netsh advfirewall firewall add rule name="Windows Cryptographic Services" action=allow enable=yes profile=any program="%SystemRoot%\system32\svchost.exe" service="CryptSvc" dir=out protocol=tcp remoteport=80,443 The problem is, this rule does not work. Unless I change the scope to "all programs and services" (which is really unhealthy), connection denied events like the following will keep appearing in the security log: Event 5157, Microsoft Windows security auditing. The Windows Filtering Platform has blocked a connection. Application Information: Process ID: 1476 (<- svchost.exe with CryptSvc and nothing else) Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Direction: Outbound Source Address: 192.168.0.1 Source Port: 49616 Destination Address: 2.16.52.16 Destination Port: 80 Protocol: 6 (<- TCP) To make sure it's CryptSvc, I have let the connection through and reviewed its traffic; I also configured CryptSvc to run in its own svchost instance to make it more obvious: ;sc config CryptSvc type= share sc config CryptSvc type= own So... why is it not matching the firewall rule, and how to fix that?

  Read the article

• what web based tool, to allow a non-technical user to manage authorized keys files on a Linux (fedora/centos/ubuntu/debian) server

  - by Tom H

  (Edit: clarification below) We have a number of groups of developers that change frequently, and a security policy to require individual logins to servers using rsa or dsa public keys, which is achieved via the standard method of adding id_dsa.pub to their authorized keys file. I am using chef to sync the user accounts across machines, however our previous method of using webmin to manage the user passwords is not designed for key based auth, and hence is not easy to use for non-technical users. The developers are logging in from the WAN using ssh, they can either provide their own key, or an administrator will send them a private key. The development machines are located in the cloud and we have a single server available to host the master set of accounts. Obviously I could deploy ldap or other centralised authentication system, but that seems a bit over blown when webmin worked well for the simple case. It is easy to achieve synchronised users, groups and passwords across a bunch of low security development boxes using webmin clustered users and groups. However looking at the currently installed webmin it is not so easy to create the authorized keys as it is to create user accounts and passwords. (its possible, but its not easy - some functionality is in the usermin module, or would required some tedious steps) Ideally I'd like a web interface that is pretty much dedicated to creating users and groups, and can generate key pairs on the fly, and can accepted pasted in public keys to add to the users authorized keys file. If the tool sync'ed the users and keys as well, that would be great, but I can use chef to do that part if the accounts are created correctly on the "master" server.

  Read the article

• Remote Desktop Printing With Color

  - by philibertperusse

  Our ACCPACC administration software runs on an off-site dedicated hosted computer, running Windows 2003 Server with a completely different NT DOMAIN. We have many users connecting to that computer remotely to perform administrative tasks such as printing cheques, printing invoices, printing POs, packing slips and so on. Basically the setup is that we are all connecting using Remote Desktop Protocol (local computers are Mac OS.X, XP SP3, Vista and Windows 7). At our office we have a DOCUCOLOR 242 printer. When printing from the ACCPACC software, it prints to the local printer in our office. This is because we are using RDP features to connect printer ressources to the remote computer. This almost works now. I had to install the printer driver software on the remote 2003 Server for the printer sharing to work. Now, everyone is able to print black and white but color is out. NOTES: Normal users on that Windows 2003 server are running as part of a Group Policy Object to restrict what can be done. I took one of these normal users and gave him all domain administrator rights, no effect still B&W only. I took this account and moved it OUT of GPO policies, as a normal account instead, no effect still B&W only. It seems only MY account (which is domain administrator AND a normal account not part of the GPO objects) can actually print with color. This is the account that was used for installing the printer driver software. How can I manage to get everyone to print in color? Any suggestions as to what to try next?

  Read the article

• Unable to install mod_wsgi on CentOS 5.5 VPS...

  - by jasonaburton

  I am trying to install mod_wsgi on my VPS, but it won't work. This is what I am doing: wget http://modwsgi.googlecode.com/files/mod_wsgi-2.5.tar.gz tar xzvf mod_wsgi-2.5.tar.gz cd mod_wsgi-2.5 ./configure --with-python=/opt/python2.5/bin/python After I run the above command, I get this error: checking for apxs2... no checking for apxs... no checking Apache version... ./configure: line 1298: apxs: command not found ./configure: line 1298: apxs: command not found ./configure: line 1299: /: is a directory ./configure: line 1461: apxs: command not found configure: creating ./config.status config.status: creating Makefile config.status: error: cannot find input file: Makefile.in Through some research I've discovered that I need to modify my command: ./configure --with-apxs=/usr/local/apache/bin/apxs \ --with-python=/usr/local/bin/python But, /usr/local/apache/ doesn't exist, or so that's what it is telling me. If it doesn't exist, how do I create it with all the files needed, or if apache is located elsewhere on my VPS where would it be located? I'd also like to mention that I ran a command to install apache before this entire deal: yum install httpd so I assumed that was all I needed but apparently not (I am very new at all this server administration stuff so please be gentle) EDIT: This is the tutorial that I have been using to get this all set up: http://binarysushi.com/blog/2009/aug/19/CentOS-5-3-python-2-5-virtualevn-mod-wsgi-and-mod-rpaf/ I got stuck at the heading "Installing mod_wsgi" Thanks for any help!

  Read the article

• How to restrict postfix send limited email with policyd v2?

  - by Shalini Tripathi

  I have installed cluebringer-2.0.7 for postfix and enabled below lines in the main.cf file of postfix. But I could not see any policy working smtpd_recipient_restrictions = permit_mynetworks permit_sasl_authenticated reject_unauth_destination check_policy_service inet:127.0.0.1:10031 smtpd_end_of_data_restrictions=check_policy_service inet:127.0.0.1:10031 To check further I enabled logging in policyd and its only shows below logs and there is no logs getting populated when I send new emails.. [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: Process Backgrounded [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Policyd v2 / Cluebringer - v2.0.7 [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Initializing system modules. [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: System modules initialized. [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Module load started... [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = AccessControl: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = CheckHelo: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = CheckSPF: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Greylisting: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Quotas: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Protocol(Postfix): enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Protocol(Bizanga): enabled [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Module load done. [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: 2012/06/12-21:18:50 cbp (type Net::Server::PreFork) starting! pid(13949) [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: Binding to TCP port 10031 on host * [2012/06/12-21:18:50 - 13949] [CORE] WARNING: Group Not Defined. Defaulting to EGID '0 10 6 4 3 2 1 0' [2012/06/12-21:18:50 - 13949] [CORE] WARNING: User Not Defined. Defaulting to EUID '0' Do I need to do anymore settings for postfix to listen on policyd???Please help

  Read the article

• Unable to ping domain.local, but can ping server.domain.local

  - by Force Flow

  I have a single windows 2008 server running active directory, group policy, and DNS. DHCP is running from the firewall (this is because there are multiple branch locations, and each location has its own firewall supplying DHCP. But, for this problem, the server and workstation are at the same location). On an XP workstation, if I try to visit \\domain.local or ping domain.local, the workstation can't find it. A ping returns Ping request could not find host domain.local. If I try to visit \\server or \\server.domain.local or ping server or server.domain.local, I'm able to connect normally. If I ping or visit domain.local on the server, I'm able to connect normally. A-Records are in place in the DNS service for server, domain.local, and server.domain.local. A reverse lookup zone also is enabled and PTR records are in place. If I wait 20-30 minutes, I am eventually able to ping and visit domain.local--but, when attempting to ping, it takes 30 second to return an IP address. I am also unable to join a new workstation to the domain during this wait period. If I try, the error message returned is "network path not found". Is there something I'm missing?

  Read the article

• DEB: "Provides:" field ignored

  - by Creshal

  I need to replace a package with a custom one, which gets its own name (foo-origpackage). To allow it to be used as drop-in replacement, I added the Provides: origpackage line to the control file. apt-cache show foo-origpackage lists the "Provides" entry just fine. However, when I want to install a file depending on origpackage, it fails ("Package origpackage not installed"). Is there some distinction between "real" and virtual packages I'm missing? EDIT: To be precise, what I want to replace is xen-utils-common for Squeeze. My tao-xen-utils-common has the following control file: Source: tao-xen-utils-common Section: kernel Priority: optional Maintainer: Creshal <[email protected]> Build-Depends: debhelper Standards-Version: 3.8.0 Homepage: http://tao.at Package: tao-xen-utils-common Architecture: all Depends: gawk, lsb-base, udev, xenstore-utils, tao-firewall Provides: xen-utils-common Conflicts: xen-utils-common Replaces: xen-utils-common Description: Xen administrative tools - common files (modified) The userspace tools to manage a system virtualized through the Xen virtual machine monitor. Modified for use with TAO Firewall. Installing xen-utils-4.0 fails, however: foo@bar# apt-cache showpkg tao-xen-utils-common Package: tao-xen-utils-common Versions: 4.0.0-1tao1 (/var/lib/apt/lists/repo.tao.at_dists_stable_main_binary-amd64_Packages) (/var/lib/dpkg/status) Description Language: File: /var/lib/apt/lists/repo.tao.at_dists_stable_main_binary-amd64_Packages MD5: 7c2503f563fca13b33b4eb3cbcb3c129 Reverse Depends: tao-firewall,tao-xen-utils-common tao-firewall,tao-xen-utils-common Dependencies: 4.0.0-1tao1 - gawk (0 (null)) lsb-base (0 (null)) udev (0 (null)) xenstore-utils (0 (null)) tao-firewall (0 (null)) xen-utils-common (0 (null)) xen-utils-common (0 (null)) Provides: 4.0.0-1tao1 - xen-utils-common Reverse Provides: foo@bar# apt-get install xen-utils-4.0 Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: xen-utils-common Suggested packages: xen-docs-4.0 The following packages will be REMOVED: tao-xen-utils-common The following NEW packages will be installed: xen-utils-4.0 xen-utils-common Edit:foo@bar# apt-cache policy xen-utils-4.0 xen-utils-4.0: Installed: (none) Candidate: 4.0.1-4 Version table: 4.0.1-4 0 500 http://ftp.at.debian.org/debian/ stable/main amd64 Packages 4.0.1-4 0 500 http://security.debian.org/ stable/updates/main amd64 Packages

  Read the article

• Dell fumbles OpenManage installation process, forgets to write documentation?

  - by bwerks

  Hi all, I'm setting up a Dell PowerEdge 2950 for a small business, and I've just spent a while with Dell OpenManage Server Administrator 6.2, trying to clear the installation process of errors before I execute it. Right now I'm getting the following warning from the installer. The installer has detected that the HTTPS listener is not configured for Windows Remote Management. You can either configure the HTTPS listener before installing Remote Enablement, or install Remote Enablement now by selecting the "Custom" installation screen and configure the HTTPS listener later. See the "Remote Enablement Requirements" section in the "Dell OpenManage Installation and Security User's Guide" for information on configuring the HTTPS listener. Note: Remote Enablement is required to manage this system from a remote Server Administrator Web Server and is applicable only for those systems that support Server Instrumentation. Click here to configure HTTPs Listener for Windows Remote Management. The italicized line is a link, which executes...something...via cmd, and doesn't seem to help the problem. Not knowing exactly what to do here, I consulted the documentation. I read through the Setup and Administration section of the User's Guide, but all that it contained was a weird primer on role-based security and some SNMP stuff. The next section skips installation entirely and moved on to features of the suite. Thinking myself crazy, I consulted the readme, which told me that for installation I should consult the "Dell OpenManage Installation and Security Version 6.2 User's Guide" which not only doesn't exist in the documentation, but also not in all of google? Soo yeah, if anyone is familiar with this problem, drop me some knowledge!

  Read the article

• Lotus Domino - DAOS not reducing file size?

  - by SydxPages

  I have implemented DAOS on a Lotus Domino Server (8.5.3 FP2) as follows: Lotus Domino Server Document: Store file attachments in DAOS: Enabled Minimum size of object before Domino will store in DAOS: 64000 bytes DAOS base path: E:\DAOS Defer object deletion for: 30 days Transaction logging is running, and the specific test database has the following advanced properties set: Domino Attachment and Object Service (ticked) Use LZ1 compression for atachments Compress Database Design Compress Data I have restarted the server. When I run a compact -c, it compacts the database, but does not reduce the size. I have checked the DB in Windows Explorer (60Gb) and the size is the same pre and post. I have checked the directory (E:\DAOS) and it is 35Gb in size. When I run the command 'Tell DAOSMgr Status tmp\test.nsf', I get the following response. From looking up on the net, I believe ticket count = 0 means that the db is not really DAOS'ed? Admin Process: Searching Administration Requests database DAOSMGR: Status tmptest.nsf started DAOS database status: Database: E:\Lotus\Domino\Data\tmp\test.nsf Database state = Synchronized Last resynchronized: 03/09/2012 02:49:13 PM Ticket count: 0 DAOSMGR: Status tmp\test.nsf completed I have run fixup on the database. When I have tried to run the DAOS estimator it has always crashed. This was a problem with larger databases on earlier versions of domino, but not anymore. Can anyone tell me why the size has not reduced? Am I missing anything?

  Read the article

• Iptables Forwarding problem

  - by ankit

  Hi all, I had initally asked question about sertting up my linux box for natting for my home network and was given suggestions in the thread here. Did not want to clutter the old question so starting a new one here. based on the earlier suggestions, i have come up with the following rules ... :PREROUTING ACCEPT [1:48] :OUTPUT ACCEPT [12:860] :POSTROUTING ACCEPT [3:228] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT *filter :INPUT DROP [3:228] :FORWARD DROP [0:0] :OUTPUT DROP [0:0] -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p icmp -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 443 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 22 -j ACCEPT -A FORWARD -i eth1 -p icmp -j ACCEPT -A FORWARD -i eth1 -p tcp -m tcp --dport 80 -j ACCEPT -A FORWARD -i eth1 -p tcp -m tcp --dport 443 -j ACCEPT -A OUTPUT -p icmp -j ACCEPT -A OUTPUT -j ACCEPT COMMIT If you notice, i do have the proper MASQURADING rule and the proper FORWARD filter rule as well. However i am facing 2 problems On the linux box itself DNS resolving is not working the lan clients connected to the linux box, are still not able to get to internet. when i ping something from them, i see the DROP count in iptables INPUT rule increasing. now my question is, when i am pinging something from the lan client, how come it is being matched by the input chain ?! should it be in the forward chain ? Chain INPUT (policy DROP 20 packets, 2314 bytes) pkts bytes target prot opt in out source destination 99 9891 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- eth0 any anywhere anywhere 0 0 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:https 122 9092 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:ssh Thanks ankit

  Read the article

• 403 Forbidden When Using AuthzSVNAccessFile

  - by David Osborn

  I've had a nicely functioning svn server running on windows that uses Apache for access. In the original setup every user had access to all repositories, but I recently needed the ability to grant a user only access to one repository. I uncommented the AuthzSVNAccessFile line in my httpd.conf file and pointed it to an accessfile and setup the access file, but I get a 403 Forbidden when I go to mydomain.com/svn . If I recomment out this line then things work again. I also made sure I uncommented the LoadModule authz_svn_module and verified that it was point to the correct file. Below is the Location section of my httpd.conf and my svnaccessfile httpd.conf (location section only) <Location /svn> DAV svn SVNParentPath C:\svn SVNListParentPath on AuthType Basic AuthName "Subversion repositories" AuthUserFile passwd Require valid-user AuthzSVNAccessFile svnaccessfile </Location> (I want a more complex policy in the long run but just did this to test the file out) svnaccessfile [svn:/] * = rw I have also tried just the below for the svnaccessfile. [/] * = rw I also restart the service after each change just to make sure it is taken.

  Read the article

• How do I make ESXi 5.0 to shutdown virtual machines when the physical power button is pushed?

  - by Pawel Sawicki

  I have a home NAS/DLNA server built out of an HP Micro Server with the HP branded VMware ESXi 5.0.0 build-623860 (free license) installed. Being a home media center I'd like it to be "manageable" by all my household members. This requires that it needs to be powered on an off (including all the VMs inside) by anybody with the physical access to the server by simply pressing the power button on the chassis. The "startup" part is easy to obtain - all I had to do was to configure the startup/shutdown policy: Once the server powers up, all VMs start as well and that's exactly what I need. Well.. it did work up until 5.0.0U1, but that's a different story: http://blogs.vmware.com/vsphere/2012/03/free-esxi-hypervisor-auto-start-breaks-with-50-update-1.html Unfortunately, pressing the power button doesn't gracefully shutdown the guest machines - they are terminated instead. If I run the "shut down" command from the vSphere Client interface guests are powered off. I'd like to get the same end result when the physical power button is switched. I've poked around a bit on the ESXi server. There's a "/sbin/shutdown.sh" script that seemed to do exactly what I need... but after trying it does exactly what the power off button. The "/etc/inittab" contains an entry for the "shutdown" level but I suppose it's not hooked to the power button. I can't find any acpi related configuration, neither do I know what exactly is executed when the power button is pressed. Does anybody have a clue how can I make the VMs shutdown automatically when the physical power switch is pressed to turn of the computer?

  Read the article

• Updating PHP on Linux - "No Packages marked for Update"?

  - by Aristotle

  I'm very new to server-administration, but I was thinking the task of updating PHP to 5.2+ should be relatively simple. Online I found that the following was allegedly sufficient to do this: yum update php But when I run this, the following is output: [root@ip-XXX-XXX-XXX-XXX /]# php -v PHP 5.1.6 (cli) (built: Jan 13 2010 17:13:05) Copyright (c) 1997-2006 The PHP Group Zend Engine v2.1.0, Copyright (c) 1998-2006 Zend Technologies [root@ip-XXX-XXX-XXX-XXX /]# yum update php Loaded plugins: fastestmirror Determining fastest mirrors * addons: p3plmirror02.prod.phx3.secureserver.net * base: p3plmirror02.prod.phx3.secureserver.net * extras: p3plmirror02.prod.phx3.secureserver.net * turbopanel-base: p3plmirror02.prod.phx3.secureserver.net * turbopanel-centos5: p3plmirror02.prod.phx3.secureserver.net * update: p3plmirror02.prod.phx3.secureserver.net addons | 951 B 00:00 addons/primary | 201 B 00:00 base | 2.1 kB 00:00 base/primary_db | 1.6 MB 00:00 extras | 1.1 kB 00:00 extras/primary | 107 kB 00:00 extras 325/325 turbopanel-base | 951 B 00:00 turbopanel-base/primary | 72 kB 00:00 turbopanel-base 494/494 turbopanel-centos5 | 951 B 00:00 turbopanel-centos5/primary | 2.1 kB 00:00 turbopanel-centos5 8/8 update | 1.9 kB 00:00 update/primary_db | 463 kB 00:00 Setting up Update Process No Packages marked for Update [root@ip-XXX-XXX-XXX-XXX /]# php -v PHP 5.1.6 (cli) (built: Jan 13 2010 17:13:05) Copyright (c) 1997-2006 The PHP Group Zend Engine v2.1.0, Copyright (c) 1998-2006 Zend Technolog [root@ip-XXX-XXX-XXX-XXX /]# No Packages marked for Update [root@ip-XXX-XXX-XXX-XXX /]# php -v bash: No: command not found [root@ip-XXX-XXX-XXX-XXX /]# [root@ip-XXX-XXX-XXX-XXX /]# php -v bash: [root@ip-XXX-XXX-XXX-XXX: command not found [root@ip-XXX-XXX-XXX-XXX /]# PHP 5.1.6 (cli) (built: Jan 13 2010 17:13:05) bash: syntax error near unexpected token `(' [root@ip-XXX-XXX-XXX-XXX /]# Copyright (c) 1997-2006 The PHP Group bash: syntax error near unexpected token `c' [root@ip-XXX-XXX-XXX-XXX /]# Zend Engine v2.1.0, Copyright (c) 1998-2006 Zend Technologies bash: syntax error near unexpected token `(' [root@ip-XXX-XXX-XXX-XXX /]# My PHP version is 5.1.6 before, and after running the command. Am I being too naive here with this update process? Is there a more verbose route that is necessary for me to take?

  Read the article

• LDAP authentication issue with Kerio Connect

  - by djk

  Hi, We have Kerio Connect (mail server) running on a Windows Server 2003 server on a domain. In the webmail client, users are able to change their domain password. This functionality used to work fine until a user tried to change their password a few days ago, when every password they'd try would result in the webmail client claiming their password was "invalid". I spoke to Kerio about this and they claim that this error is returned by the domain controller, which supports my initial investigations. The error that the DC is logging when an attempt is made to change the password is this: "80090308: LdapErr: DSID-0C090334, comment: AcceptSecurityContext error, data 52e, vece" The "data 52e" part indicates that this is an "invalid credentials" error. I don't see how this can be as I've tried (in the Kerio Connect configuration) various accounts that have privileges to modify accounts, including my own as I am a domain admin. I have ran 'dcdiag' (all tests) on the DC and it came back passing every single one of them. I've searched high and low for an answer to this and came up empty. Does anyone have any idea why this may have suddenly started happening? Thanks! Edit: I should mention that the passwords we are changing to do comply with the complexity policy.

  Read the article

• Kickstart CentOS 6 prompting for TCP/IP with network set to DHCP

  - by Andy Shinn

  I am trying to stop my kickstart CentOS install prompting me for TCP/IP information. After I click through this prompt (keeping IPv4 and IPv6 to their defaults) the installation continues and completes just fine. Below is my kickstart file: # Andy's super awesome VM kickstart file install url --url=http://mirrors.kernel.org/centos/6/os/x86_64 lang en_US.UTF-8 keyboard us text %include /tmp/network.ks rootpw --iscrypted $6$RA8DyrNTsVJkGIgY$ohZ62HHiOjNnn1yDMZlIu3lQ63D3plGPcbVZtPKE8Oq6Z.IGUgN.kNLkxs/ZymZuluRDWsW2eey5zLOl2G3mp. firewall --service=ssh authconfig --enableshadow --passalgo=sha512 selinux --disabled timezone America/Los_Angeles bootloader --location=mbr --driveorder=vda --append="crashkernel=auto rhgb quiet" # The following is the partition information you requested # Note that any partitions you deleted are not expressed # here so unless you clear all partitions first, this is # not guaranteed to work zerombr clearpart --all --drives=vda --initlabel part /boot --fstype=ext4 --size=500 part pv.253002 --grow --size=1 volgroup vg1 --pesize=4096 pv.253002 logvol / --fstype=ext4 --name=lv_root --vgname=vg1 --grow --size=1024 --maxsize=51200 logvol swap --name=lv_swap --vgname=vg1 --grow --size=4032 --maxsize=4032 repo --name="CentOS" --baseurl=http://mirrors.kernel.org/centos/6/os/x86_64 --cost=100 repo --name="Puppet Labs Products" --baseurl=http://yum.puppetlabs.com/el/6/products/x86_64 repo --name="Puppet Labs Dependencies" --baseurl=http://yum.puppetlabs.com/el/6/dependencies/x86_64 repo --name="EyeFi" --baseurl=http://flexo.eye.fi/6/eye-fi-api %packages @core @server-policy puppet facter %end %pre --erroronfail #!/bin/bash for x in `cat /proc/cmdline`; do case $x in SERVERNAME*) eval $x echo "network --onboot yes --device eth0 --bootproto dhcp --hostname ${SERVERNAME}.eye.fi" /tmp/network.ks ;; esac; done %end %post puppet agent --waitforcert 10 --onetime --no-daemon --pluginsync --server puppet.eye.fi %end reboot My kernel arguments are in this following virt-install command that I use to start the install: virt-install -n zabbix -r 2048 --vcpus=2 -l http://mirrors.kernel.org/centos/6/os/x86_64 --disk /dev/vg_inf1/zabbix --network bridge=br85 --initrd-inject=/home/ashinn/vm_kickstart --extra-args "ks=file:/vm_kickstart SERVERNAME=zabbix" --autostart During the install, I can pull up a console on the second terminal and verify the contents of /tmp/network.ks are: network --onboot=yes --bootproto=dhcp --ipv6=auto --hostname=jenkins2.mydomain.com Why might Anaconda be prompting for the TCP/IP settings when they are already set to DHCP?

  Read the article

• Terminal Server 2008: Remote App Issue

  - by JohnyD

  I have a FoxPro 2.6 (16-bit) application that I've installed on a Win2008 (32-bit) Terminal Server. I then created a Remote App from it. It works fine. The problem is that within this FoxPro application it calls out to a .Net application. I have the proper .Net Framework installed on the server (2.0) and I have run the code access security policy tool (caspol.exe). However, when I launch the .Net app from within the FoxPro application I get the following error: Description: Stopped working Problem signature: Problem Event Name: CLR20r3 Problem Signature 01: vector.exe Problem Signature 02: 1.0.0.3 Problem Signature 03: 48b579f2 Problem Signature 04: vector Problem Signature 05: 1.0.0.3 Problem Signature 06: 48b579f2 Problem Signature 07: f Problem Signature 08: 57 Problem Signature 09: System.Security.Security OS Version: 6.0.6001.2.1.0.18.10 Locale ID: 1033 Vector.exe is our .Net application. In fact, it's an in-between application that checks to ensure you have the latest version. When it's done it calls out to another .Net executable. Does anyone believe this should be a problem? Thanks in advance.

  Read the article

• Windows 7 libraries nightmare

  - by Lobuno

  In our active directory we deploy a policy to our clients where the personal directory (My documents) is redirected to a file server of ours \server\share\username\Documents In older systems everything worked fine. in Windows 7 some users are experimenting the following symptoms: The Documents library is EMPTY Where the documents library should be shown in Explorer an empty white icon is displayed. No caption. Right clicking in the Documents library to edit the folders that are part of the libraries brings the dialog up. However, that dialog is unusable. No folder is present there and clicking Add folder does nothing. Deleting the library and auto-creating it doesn't solve the problem The shared directory can be accessed via UNC paths and it can be mounted as a shared drive as well. The library is still broken. The shared drives are on a W2008 indexed server... Using the Windows Library tool utility doesn't solve the problem. What can the cause of this problem be and how can this be solved?

  Read the article

• What is the latest on Microsoft Expressoin Studio licensing?

  - by DanM

  In the past, there's been an issue with Microsoft not allowing you to deactivate an Expression Studio key. Basically, you get two keys per license. If you assign both keys (say one to a desktop and one to a laptop), then you upgrade to a new machine (say you replace your laptop or upgrade some of the hardware), you have to buy a new copy of Expression Studio ($600 for Ultimate). This seems ludicrous to me, and I'm wondering if anyone knows if this policy is still in place. I can't seem to find a EULA online anywhere, so I don't know where to find this information. I know my laptop is due for replacement soon, and I want to know if I'm going to have to sink $600 into a software product I already purchased. For background, please refer to this thread on the Microsoft Expression forums: http://social.expression.microsoft.com/Forums/en-US/general/thread/da5587bc-b098-4c6a-9a56-af3608d940d0 Note that this thread is locked. Microsoft doesn't seem to want people to discuss this. This is one reason I'm posting here rather than on that site.

  Read the article

• Remote assistance from Remote Desktop sessions: unable to control

  - by syneticon-dj

  Since Remote Control (aka Session Shadowing) is gone for good in Server 2012 Remote Desktop Session hosts, I am looking for a replacement to support users in a cross-domain environment. Since Remote Assistance is supposed to work for Remote Desktop Sessions as well, I tried leveraging that for support purposes by enabling unsolicited remote assistance for all Remote Desktop Session Hosts via Group Policy. All seems to be working well except that the "expert" seems to be unable to actually excercise any mouse or keyboard control when the remote assistance session has been initiated from a Remote Desktop session itself. Mouse clicks and keyboard strokes from the "expert" session (Server 2012) seem to simply be ignored even after the assisted user has acknowledged the request for control. I would like to see this working through RD sessions for the support staff due to a number of reasons: not every support agent would have the appropriate client system version to support users on a specific terminal server (e.g. an agent might have a Windows Vista or Windows 7 station and thus be unable to offer assistance to users on Server 2012 RDSHs) a support agent would not necessarily have a station which is a member of the specific destination domain (mainly due to the reason that more than a single domain's users are supported) what am I missing?

  Read the article

• Is it possible to stop the "Beep" device on all computers in a Windows network?

  - by sharptooth

  On Windows the default behavior it to make an annoying "beep" sound every time Windows things something notable happened. The result is that when someone send a company-wide email via the MS Exchange all computers around my cubicle beep one by one. This is annoying and makes no sense. Luckily beeping can be shut off. Someone has to: open the "Device Manager", select "View - Show hidden devices", find the "Beep" device in "Non-Pug and Play Devices" node, open its properties, go to the "Driver" tab, set "startup type" to "Disabled" and click "Stop". The "Beep" device will stop and no longer produce the useless sound. This solution however requires tracking every computer and then talking to its user which is not very convenient. Device Manager doesn't allow stopping a device on another computer. I'm looking for a solution that can be deployed by the administrators team. We have a domain and the administrators even install the programs company-wide automatically. Are there any means to stop the "Beep" device an all computers in the Windows network with some remote-administration features automatically?

  Read the article

• How to route to a secondary interface on the same physical ethernet?

  - by sjose3612611

  INTERNET<->(wan)BRIDGED_DEVICE(lan)<->ETH_ROUTER<->LAN Problem: Need to access web server on BRIDGED_DEVICE's LAN from INTERNET via ROUTER (BRIDGED_DEVICE's web server cannot be accessed form INTERNET since it has no Public management IP). Cannot configure bridged device. It has a static IP on its LAN to which its web server binds. Attempt: Create a secondary/alias WAN Interface on ETH_ROUTER (e.g Primary: eth0.1 (for internet access) and Secondary: eth0.2 (for accessing web server on BRIDGED_DEVICE), (No VLANs). eth0.1 has a public IP; eth0.2 has a static private IP in the BRIDGED_DEVICE's subnet (e.g 10.0.X.Y). Iptables on ETH_ROUTER: Added a port forward (DNAT) from eth0.1 to eth0.2: iptables -t nat -I PREROUTING -i eth0.1 -p tcp --dport 80 -j DNAT --to-destination 10.0.X.Y iptables -t nat -I POSTROUTING -o eth0.2 -s 10.0.X.0/24 -j MASQUERADE Stateful firewall w/ overall drop policy on FORWARD chain, hence: iptables -I FORWARD -i eth0.1 -d 10.0.X.Y -p tcp --dport 80 -j ACCEPT Can ping from ETH_ROUTER to BRIDGED_DEVICE but unable to reach the web server from Internet. I see packet cont increasing for the DNAT rule but not sure where it disappears in the ETH_ROUTER after that. ETH_ROUTER is the only device that can be configured to achieve this. If familiar with this scenario, please suggest what I may be missing or doing wrong here or suggest techniques to debug?

  Read the article

• Apple Mac OS X Mavericks inside Virtual Box

  - by John Sonderson

  I have a few questions regarding Mac OS X and OS virtualization. A. Given all the legal restrictions imposed by Apple on Apple products, I would like to know whether it is legal to install the new and freely downloadable Apple Mac OS X Mavericks inside Oracle Virtual Box. B. What about older OS X versions such as Mountain Lion? C. How many machines can I install it on. What if I don't use the Mac to which the OS is downloaded but only use it on Virtual Box, and prefer to, say, install Linux on the Mac computer so that it doesn't become unusable due to the single user license policy and me running the OS on Windows 7 within Virtual Box? D. I have a PC running Windows 7 but would like to get the OS off a second had Mac I'm planning to purchase for this purpose. How must we proceed to copy the OS to an ISO so that I can install it on Windows 7? I am unfamiliar with Macs and do not know what software to use for the purpose, nor where the OS is downloaded to (as an ISO, .app executable, .gz or .zip file or whatever). If anyone could provide some guidance with the process I would sincerely appreciate it. Thanks.

  Read the article

• How do I force a server to leave a SharePoint farm

  - by Stefan

  I have two web servers in a SharePoint (WSS 3.0) farm with one database server for the config and content databases. I already moved my content databases to a new database server successfully. But when I tried to move the sharepoint config database using the "stsadm deleteconfigdb" and "stsadm setconfigdb" commands, one of my servers got stuck in an intermediate state. I was able to join one of the web servers with the config database on the new server, but the other server is not able to join because it believes it is already part of the farm (which it used to be, before the move). On the central administration it says the status of the services on the server is "stopping". Even after rebooting all servers involved, uninstalling SharePoint and what not, this status does not change, and because of it, I am not able to join the second server with the new config database. I get random error messages when trying to join the farm. I believe that if I can unstuck this server, it will be able to join the farm again. The farm believes the second server is already part of it, but the web server itself knows its not. Any ideas on how to forcefully kick out a server from the farm?

  Read the article

< Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >