Search Results

Search found 12790 results on 512 pages for 'port islander 2009'.

Page 151/512 | < Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >

• Lenovo S110 netbook screen resolution Ubuntu

  - by Neigyl R. Noval

  I am still stuck with 800x600 resolution. Here is the output of lspci: 00:00.0 Host bridge: Intel Corporation Device 0bf2 (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Device 0be2 (rev 09) 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02) 00:1c.2 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 3 (rev 02) 00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation N10/ICH7 Family SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 02) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8176 (rev 01) Also, I tried modifying /usr/lib/X11/xorg.conf.d/10-monitor.conf to fix this problem, but still does not work: Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Screen" Identifier "Screen0" Monitor "Monitor0" Device "Card0" SubSection "Display" Viewport 0 0 Depth 1 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 4 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 8 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 15 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 16 Modes "1024x768" EndSubSection SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" EndSubSection EndSection Section "Device" Identifier "Card0" Driver "vesa" VendorName "Intel Corporation Device" EndSection I'm using Gnome. System Preference Monitor screen resolution sticks to 800x600. What am I going to do?

  Read the article

• Strange Ubuntu Random Display [Video]

  - by d4v1dv00

  I had this random display issue ever since Ubuntu 11.04 and now running Ubuntu 11.10 and this problem still persist. It is very hard for me to explain, so I uploaded a video to elaborate itself. Before I convert from Windows 7, this issue never happened. The symptom is so random that I cannot reproduce or tell precisely when will this happen again. My wild guess is, should this be related to driver? Below are my detail system information: $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation H67 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57788 Gigabit Ethernet PCIe (rev 01) is there any other information i need to post and how do i do that?

  Read the article

• Oracle and Cavium to work together on Java SE 8 on 64-bit ARMv8

  - by Henrik Stahl

  We have been working for some time on a standard Oracle JDK 8 port to the upcoming introduction of 64-bit servers based on the new ARMv8 micro architecture. At ARM TechCon 2013 in Santa Clara, California, we announced a roadmap with an expected GA in 2015. This project is going very well and is ahead of schedule. We will soon be at the point where we will make binaries available outside of Oracle - first in a managed beta program with select customers/partners, and sometime during the fall of 2014 as a public early access program. Unless something changes, we are looking at a early 2015 GA. We should be able to share a detailed ramp down and GA plan by JavaOne 2014. One of the things we (obviously) need to produce a high-quality port is hardware for development and QA. We are therefore happy to announce that we will be collaborating with Cavium on this project. Cavium has been a supporter of the Java ecosystem for a long time and we have numerous joint customers running various Java versions on Cavium MIPS and ARM-based hardware. Cavium has now agreed to provide us with development hardware and engineering resources so that we can certify and optimize the initial Oracle JDK 8 release on Cavium's ThunderX hardware. This is expected to improve quality and performance of JDK 8 on ARMv8 in general, as well as on Cavium's hardware. For more information: Cavium announcement on the ThunderX product family Cavium announcement on Oracle collaboration As a reminder, we plan to release the Oracle JDK 8 port to 64-bit ARMv8 under the royalty-free (for general purpose servers etc) Binary Code License, but we have no current plans to open source it.

  Read the article

• BizTalk and SQL: Alternatives to the SQL receive adapter. Using Msmq to receive SQL data

  - by Leonid Ganeline

  If we have to get data from the SQL database, the standard way is to use a receive port with SQL adapter. SQL receive adapter is a solicit-response adapter. It periodically polls the SQL database with queries. That’s only way it can work. Sometimes it is undesirable. With new WCF-SQL adapter we can use the lightweight approach but still with the same principle, the WCF-SQL adapter periodically solicits the database with queries to check for the new records. Imagine the situation when the new records can appear in very broad time limits, some - in a second interval, others - in the several minutes interval. Our requirement is to process the new records ASAP. That means the polling interval should be near the shortest interval between the new records, a second interval. As a result the most of the poll queries would return nothing and would load the database without good reason. If the database is working under heavy payload, it is very undesirable. Do we have other choices? Sure. We can change the polling to the “eventing”. The good news is the SQL server could issue the event in case of new records with triggers. Got a new record –the trigger event is fired. No new records – no the trigger events – no excessive load to the database. The bad news is the SQL Server doesn’t have intrinsic methods to send the event data outside. For example, we would rather use the adapters that do listen for the data and do not solicit. There are several such adapters-listeners as File, Ftp, SOAP, WCF, and Msmq. But the SQL Server doesn’t have methods to create and save files, to consume the Web-services, to create and send messages in the queue, does it? Can we use the File, FTP, Msmq, WCF adapters to get data from SQL code? Yes, we can. The SQL Server 2005 and 2008 have the possibility to use .NET code inside SQL code. See the SQL Integration. How it works for the Msmq, for example: ·         New record is created, trigger is fired ·         Trigger calls the CLR stored procedure and passes the message parameters to it ·         The CLR stored procedure creates message and sends it to the outgoing queue in the SQL Server computer. ·         Msmq service transfers message to the queue in the BizTalk Server computer. ·         WCF-NetMsmq adapter receives the message from this queue. For the File adapter the idea is the same, the CLR stored procedure creates and stores the file with message, and then the File adapter picks up this file. Using WCF-NetMsmq adapter to get data from SQL I am describing the full set of the deployment and development steps for the case with the WCF-NetMsmq adapter. Development: 1.       Create the .NET code: project, class and method to create and send the message to the MSMQ queue. 2.       Create the SQL code in triggers to call the .NET code. Installation and Deployment: 1.       SQL Server: a.       Register the CLR assembly with .NET (CLR) code b.      Install the MSMQ Services 2.       BizTalk Server: a.       Install the MSMQ Services b.      Create the MSMQ queue c.       Create the WCF-NetMsmq receive port. The detailed description is below. Code .NET code … using System.Xml; using System.Xml.Linq; using System.Xml.Serialization;   //namespace MyCompany.MySolution.MyProject – doesn’t work. The assembly name is MyCompany.MySolution.MyProject // I gave up with the compound namespace. Seems the CLR Integration cannot work with it L. Maybe I’m wrong.     public class Event     {         static public XElement CreateMsg(int par1, int par2, int par3)         {             XNamespace ns = "http://schemas.microsoft.com/Sql/2008/05/TypedPolling/my_storedProc";             XElement xdoc =                 new XElement(ns + "TypedPolling",                     new XElement(ns + "TypedPollingResultSet0",                         new XElement(ns + "TypedPollingResultSet0",                             new XElement(ns + "par1", par1),                             new XElement(ns + "par2", par2),                             new XElement(ns + "par3", par3),                         )                     )                 );             return xdoc;         }     }   //////////////////////////////////////////////////////////////////////// … using System.ServiceModel; using System.ServiceModel.Channels; using System.Transactions; using System.Data; using System.Data.Sql; using System.Data.SqlTypes;   public class MsmqHelper {     [Microsoft.SqlServer.Server.SqlProcedure]     // msmqAddress as "net.msmq://localhost/private/myapp.myqueue";     public static void SendMsg(string msmqAddress, string action, int par1, int par2, int par3)     {         using (TransactionScope scope = new TransactionScope(TransactionScopeOption.Suppress))         {             NetMsmqBinding binding = new NetMsmqBinding(NetMsmqSecurityMode.None);             binding.ExactlyOnce = true;             EndpointAddress address = new EndpointAddress(msmqAddress);               using (ChannelFactory<IOutputChannel> factory = new ChannelFactory<IOutputChannel>(binding, address))             {                 IOutputChannel channel = factory.CreateChannel();                 try                 {                     XElement xe = Event.CreateMsg(par1, par2, par3);                     XmlReader xr = xe.CreateReader();                     Message msg = Message.CreateMessage(MessageVersion.Default, action, xr);                     channel.Send(msg);                     //SqlContext.Pipe.Send(…); // to test                 }                 catch (Exception ex)                 { …                 }             }             scope.Complete();         }     }   SQL code in triggers   -- sp_SendMsg was registered as a name of the MsmqHelper.SendMsg() EXEC sp_SendMsg'net.msmq://biztalk_server_name/private/myapp.myqueue', 'Create', @par1, @par2, @par3   Installation and Deployment On the SQL Server Registering the CLR assembly 1.       Prerequisites: .NET 3.5 SP1 Framework. It could be the issue for the production SQL Server! 2.       For more information, please, see the link http://nielsb.wordpress.com/sqlclrwcf/ 3.       Copy files: >copy “\Windows\Microsoft.net\Framework\v3.0\Windows Communication Foundation\Microsoft.Transactions.Bridge.dll” “\Program Files\Reference Assemblies\Microsoft\Framework\v3.0 \Microsoft.Transactions.Bridge.dll” If your machine is a 64-bit, run two commands: >copy “\Windows\Microsoft.net\Framework\v3.0\Windows Communication Foundation\Microsoft.Transactions.Bridge.dll” “\Program Files (x86)\Reference Assemblies\Microsoft\Framework\v3.0 \Microsoft.Transactions.Bridge.dll” >copy “\Windows\Microsoft.net\Framework64\v3.0\Windows Communication Foundation\Microsoft.Transactions.Bridge.dll” “\Program Files\Reference Assemblies\Microsoft\Framework\v3.0 \Microsoft.Transactions.Bridge.dll” 4.       Execute the SQL code to register the .NET assemblies: -- For x64 OS: CREATE ASSEMBLY SMdiagnostics AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v3.0\Windows Communication Foundation\SMdiagnostics.dll' WITH permission_set = unsafe CREATE ASSEMBLY [System.Web] AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework64\v2.0.50727\System.Web.dll' WITH permission_set = unsafe CREATE ASSEMBLY [System.Messaging] AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v2.0.50727\System.Messaging.dll' WITH permission_set = unsafe CREATE ASSEMBLY [System.ServiceModel] AUTHORIZATION dbo FROM 'C:\Program Files (x86)\Reference Assemblies\Microsoft\Framework\v3.0\System.ServiceModel.dll' WITH permission_set = unsafe CREATE ASSEMBLY [System.Xml.Linq] AUTHORIZATION dbo FROM 'C:\Program Files\Reference Assemblies\Microsoft\Framework\v3.5\System.Xml.Linq.dll' WITH permission_set = unsafe   -- For x32 OS: --CREATE ASSEMBLY SMdiagnostics AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v3.0\Windows Communication Foundation\SMdiagnostics.dll' WITH permission_set = unsafe --CREATE ASSEMBLY [System.Web] AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v2.0.50727\System.Web.dll' WITH permission_set = unsafe --CREATE ASSEMBLY [System.Messaging] AUTHORIZATION dbo FROM 'C:\Windows\Microsoft.NET\Framework\v2.0.50727\System.Messaging.dll' WITH permission_set = unsafe --CREATE ASSEMBLY [System.ServiceModel] AUTHORIZATION dbo FROM 'C:\Program Files\Reference Assemblies\Microsoft\Framework\v3.0\System.ServiceModel.dll' WITH permission_set = unsafe 5.       Register the assembly with the external stored procedure: CREATE ASSEMBLY [HelperClass] AUTHORIZATION dbo FROM ’<FilePath>MyCompany.MySolution.MyProject.dll' WITH permission_set = unsafe where the <FilePath> - the path of the file on this machine! 6. Create the external stored procedure CREATE PROCEDURE sp_SendMsg (        @msmqAddress nvarchar(100),        @Action NVARCHAR(50),        @par1 int,        @par2 int,        @par3 int ) AS EXTERNAL NAME HelperClear.MsmqHelper.SendMsg   Installing the MSMQ Services 1.       Check if the MSMQ service is NOT installed. To check:  Start / Administrative Tools / Computer Management, on the left pane open the “Services and Applications”, search to the “Message Queuing”. If you cannot see it, follow next steps. 2.       Start / Control Panel / Programs and Features 3.       Click “Turn Windows Features on or off” 4.       Click Features, click “Add Features” 5.       Scroll down the feature list; open the “Message Queuing” / “Message Queuing Services”; and check the “Message Queuing Server” option  6.       Click Next; Click Install; wait to the successful finish of the installation Creating the MSMQ queue We don’t need to create the queue on the “sender” side. On the BizTalk Server Installing the MSMQ Services The same is as for the SQL Server. Creating the MSMQ queue 1.       Start / Administrative Tools / Computer Management, on the left pane open the “Services and Applications”, open the “Message Queuing”, and open the “Private Queues”. 2.       Right-click the “Private Queues”; choose New; choose “Private Queue”. 3.       Type the Queue name as ’myapp.myqueue'; check the “Transactional” option. Creating the WCF-NetMsmq receive port I will not go through this step in all details. It is straightforward. URI for this receive location should be 'net.msmq://localhost/private/myapp.myqueue'. Notes ·         The biggest problem is usually on the step the “Registering the CLR assembly”. It is hard to predict where are the assemblies from the assembly list, what version should be used, x86 or x64. It is pity of such “rude” integration of the SQL with .NET. ·         In couple cases the new WCF-NetMsmq port was not able to work with the queue. Try to replace the WCF- NetMsmq port with the WCF-Custom port with netMsmqBinding. It was working fine for me. ·         To test how messages go through the queue you can turn on the Journal /Enabled option for the queue. I used the QueueExplorer utility to look to the messages in Journal. The Computer Management can also show the messages but it shows only small part of the message body and in the weird format. The QueueExplorer can do the better job; it shows the whole body and Xml messages are in good color format.

  Read the article

• Setting up Beats audio on HP Pavilion m6

  - by Joel Auterson

  I have an HP Pavilion m6-1054sa laptop, with a Beats subwoofer on the bottom. The normal laptop speakers work fine under Ubuntu but the Beats speaker(s?) does not. Anyone know how to get this working? Here's my lspci output, if it helps... 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Thames XT/GL [Radeon HD 7600M Series] (rev ff) 07:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5289 (rev 01) 07:00.2 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 0a) 08:00.0 Network controller: Intel Corporation Centrino Wireless-N 2230 (rev c4)

  Read the article

• Youtube video streaming slow

  - by Newbie

  When I try to stream youtube videos on my ubuntu 11.04, they don't stream smoothly. They buffer well and are choppy. Here's my Config: Laptop: Gateway NV58 Ram : 4 GB Ethernet Controller: Broadcom Corp NetLink BCM5784M Gigabit Ethernet PCIe (rev10) Let me know if you need more details. Output of lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 02:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe (rev 10) 04:00.0 Network controller: Intel Corporation WiFi Link 5100

  Read the article

• GNOME PPP doesn't connect

  - by Motorhead

  I am a new ubuntu user and connect to the internet using wi-fi broadband on my notebook. But I need to setup a dial-up connection through my phone which can keep me online while I travel. I have tried connecting to dial-up using pppconfig, wvdial and gnome-ppp. I do not know whether they use the same files for connecting but I have only been able to connect using Gnome-ppp. But the connection is intermittent and disconnects every five seconds or so. The exit code is 16 which I checked in man and got to know that the modem hangs itself up. I am connecting my phone to ubuntu as a usb modem. And as I am new I might have skipped a step or two. Please suggest a solution or an alternative to this. I have put down the Gnome-ppp log. Thanks. --> WvDial: Internet dialer version 1.61 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Modem initialized. --> Sending: ATM1L3DT*99***1# --> Waiting for carrier. ATM1L3DT*99***1# CONNECT --> Carrier detected. Waiting for prompt. ~[7f]}#@!}!}$} }=}!}$}%\}"}&} } } } }#}%B#}%}%}&}*urW}'}"}(}"mX~ --> PPP negotiation detected. --> Starting pppd at Sat Apr 28 21:55:55 2012 --> Warning: Could not modify /etc/ppp/chap-secrets: Permission denied --> --> CHAP (Challenge Handshake) may be flaky. --> Pid of pppd: 2459 --> Using interface ppp0 --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> Disconnecting at Sat Apr 28 21:56:01 2012 --> The PPP daemon has died: A modem hung up the phone (exit code = 16) --> man pppd explains pppd error codes in more detail. --> Try again and look into /var/log/messages and the wvdial and pppd man pages for more information. --> Auto Reconnect will be attempted in 5 seconds --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Modem initialized. --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Modem initialized. --> Sending: ATM1L3DT*99***1# --> Waiting for carrier. ATM1L3DT*99***1# CONNECT --> Carrier detected. Waiting for prompt. ~[7f]}#@!}!Q} }=}!}$}%\}"}&} } } } }#}%B#}%}%}&}*u69}'}"}(}"#W~ --> PPP negotiation detected. --> Starting pppd at Sat Apr 28 21:56:07 2012 --> Warning: Could not modify /etc/ppp/chap-secrets: Permission denied --> --> CHAP (Challenge Handshake) may be flaky. --> Pid of pppd: 2470 --> Using interface ppp0 --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> Disconnecting at Sat Apr 28 21:56:09 2012 --> The PPP daemon has died: A modem hung up the phone (exit code = 16) --> man pppd explains pppd error codes in more detail. --> Try again and look into /var/log/messages and the wvdial and pppd man pages for more information. --> Auto Reconnect will be attempted in 10 seconds --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Modem initialized. --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Modem initialized. --> Sending: ATM1L3DT*99***1# --> Waiting for carrier. ATM1L3DT*99***1# CONNECT --> Carrier detected. Waiting for prompt. ~[7f]}#@!}!@} }=}!}$}%\}"}&} } } } }#}%B#}%}%}&}*uvM}'}"}(}"p}$~ --> PPP negotiation detected. --> Starting pppd at Sat Apr 28 21:56:20 2012 --> Warning: Could not modify /etc/ppp/chap-secrets: Permission denied --> --> CHAP (Challenge Handshake) may be flaky. --> Pid of pppd: 2481 --> Using interface ppp0 --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> pppd: xu! --> Disconnecting at Sat Apr 28 21:56:25 2012 --> The PPP daemon has died: A modem hung up the phone (exit code = 16) --> man pppd explains pppd error codes in more detail. --> Try again and look into /var/log/messages and the wvdial and pppd man pages for more information. --> Auto Reconnect will be attempted in 20 seconds --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Modem initialized.

  Read the article

• What am I doing wrong in my config for MySql?

  - by Knight Hawk3

  When I load my my.conf with the config at the bottom Mysql fails to start and prints no errors. I am running Arch Linux (Updated) with the latest MySQL (5.5) and the latest nginx (Well latest in the repository, Not sure how to check. Only installed it today) I will give you any info you ask for. Thanks for helping! # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/run/mysqld/mysqld.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/run/mysqld/mysqld.sock skip-locking key_buffer = 16K max_allowed_packet = 1M table_cache = 4 sort_buffer_size = 64K read_buffer_size = 256K read_rnd_buffer_size = 256K net_buffer_length = 2K thread_stack = 64K # Don’t listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (using the “enable-named-pipe” option) will render mysqld useless! # #skip-networking server-id = 1 # Uncomment the following if you want to log updates #log-bin=mysql-bin # Uncomment the following if you are NOT using BDB tables skip-bdb # Uncomment the following if you are using InnoDB tables #innodb_data_home_dir = /var/lib/mysql/ #innodb_data_file_path = ibdata1:10M:autoextend #innodb_log_group_home_dir = /var/lib/mysql/ #innodb_log_arch_dir = /var/lib/mysql/ # You can set .._buffer_pool_size up to 50 – 80 % # of RAM but beware of setting memory usage too high #innodb_buffer_pool_size = 16M #innodb_additional_mem_pool_size = 2M # Set .._log_file_size to 25 % of buffer pool size #innodb_log_file_size = 5M #innodb_log_buffer_size = 8M #innodb_flush_log_at_trx_commit = 1 #innodb_lock_wait_timeout = 50 skip-innodb [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 1M sort_buffer_size = 1M [myisamchk] key_buffer = 1M sort_buffer_size = 1M [mysqlhotcopy] interactive-timeout So what is my silly error?

  Read the article

• Looking for someone to point me in the right direction. I want to learn how to use hosted servers

  - by Leisure

  TL;DR: I want a Java program to run on a server, I want the server to forward a particular port from external to internal IP, I want store a few files on the server. Guides please. So I made a hack job Java program that acts as a server for my android application. It stores data in text files and HTML files, uploads them via FTP to my webhost, and manages socket connections (using port forwarding) with any phones connected. Right now I'm running it on NetBeans on my home computer. I know that it will probably slow down or crash once about 50 phones are connected at once. Is there any way I can run this program on a server with a high bandwidth? Can someone please find me a guide for that? I'm noob and don't know where to start looking. I seriously don't know anything about renting or using servers - I need a nice guide, and recommendations. My requirements for the server: Can handle about 2k socket connections at once Can run my Java code and store my txt files Can give me a port and an IP address so TCP/IP clients can be connected My budget: $50 CAD per month. Please someone set my ship sailing in the right direction, I really don't know where to look for resources.

  Read the article

• USB device not accepting address

  - by Mike Williamson

  I have a series of machines that I am building for work that have usb card readers. When I boot them I get a long series of messages: ... [ 2347.768419] hub 1-6:1.0: unable to enumerate USB device on port 6 [ 2347.968178] usb 1-6.6: new full-speed USB device number 10 using ehci_hcd [ 2352.552020] usb 1-6.6: device not accepting address 10, error -32 [ 2352.568421] hub 1-6:1.0: unable to enumerate USB device on port 6 [ 2352.768179] usb 1-6.6: new full-speed USB device number 12 using ehci_hcd [ 2357.352033] usb 1-6.6: device not accepting address 12, error -32 ... On some older machines this only takes a few attempts before the card reader finally accepts an address, while on newer machines it can take many minutes. Changing hardware is not an option and plugging the usb card reader into a different port is only an option for the older manchines. This was a problem under 11.04 and I am now running the 12.04 beta and its still happening. Is there something I can do in the software (a udev rule perhaps?) that would fix this? Any advice appreciated. I'm happy to provide more details if you need them.

  Read the article

• Use two networks at the same time?

  - by Christopher

  I want to use Ubuntu 10.10 Server in a classroom, a computer lab whose bandwidth is provided by a local cable ISP. That's no problem, though the school network has an IP printer that I want to use. I cannot reach the printer through the cable Internet. But, I have two network cards. How is it possible to use both networks at once? eth0 (static 192.168.1.254) is plugged into a four-port router, 192.168.1.1. On the public side of the four-port router is Internet provided by the cable company. I also have the classroom workstations plugged into a switch. The switch is plugged into the four-port router. The whole classroom is wired into the cable Internet. The other NIC, eth1, could it be plugged into an Ethernet jack in the wall? It uses the school network, and I might receive by DHCP an IP address like 10.140.10.100, with the printer on maybe 10.120.50.10. I was thinking about installing the printer on the server so that it could be shared with the workstations. But how does this work? Can I just plug eth1 into the school network and access both LANs? Thanks for any insight

  Read the article

• How do I require use of the 5 GHz band when connecting to a Wireless N access point?

  - by cqcallaw

  What is says in the topic: there's a Wireless N access point to which I'd like to connect using the 5 GHz band exclusively. How does one accomplish this? Using the directive band=a in the connection configuration file in /etc/NetworkManager/system-connections doesn't seem to affect anything (/var/log/syslog still shows attempts by wpa_supplicant to connect using the 2.4 GHz band), and running iwconfig wlan0 freq 5G per this question results in the following error: Error for wireless request "Set Frequency" (8B04) : SET failed on device wlan0 ; Invalid argument. [Edit] I'm hoping the answer won't depend on the hardware in use, but here's some information about the hardware, just in case: System is an Asus ZenBook Prime UX31A-DB51, running Ubuntu 12.04. lspci output: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:04.0 Signal processing controller: Intel Corporation Device 0153 (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 00:1f.6 Signal processing controller: Intel Corporation Panther Point Thermal Management Controller (rev 04) 02:00.0 Network controller: Intel Corporation Centrino Advanced-N 6235 (rev 24) The driver for the wireless interface is iwlwifi.

  Read the article

• LIfebook lh531 inbuilt card reader not working

  - by chandrasekar

  Inbuilt card reader (SD/PRO/SDHC) not working. When I insert the memory card the indicator comes for a milli second and nothing happens. When I do lspci it gives the out put which is pasted below: I use Ubuntu 11.10. Pl help pro-hq@prohq-LIFEBOOK-LH531:~$ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 Network controller: Intel Corporation Centrino Advanced-N 6205 (rev 34) 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) pro-hq@prohq-LIFEBOOK-LH531:~$

  Read the article

• Ethernet Connection Unavailable

  - by fabikw

  I'm running Ubuntu Server 12.04 on a laptop with an Intel NIC (driver e1000e). When I connect the ethernet port to the internet (college network, DHCP) it works out of the box. Now I'm trying to connect it to a networked USRP (if you want to know what it is). A friend of mine managed to do this in his laptop (running regular Ubuntu 12.04) just by setting up a new Wired connection in the Network Manager with appropriate addresses. However, when I do the same, no wired connections are available. The output of nmcli -p dev is =========================================== Status of devices =========================================== DEVICE TYPE STATE ------------------------------------------- wlan0 802-11-wireless connected eth0 802-3-ethernet unavailable but the cable is connected to the device and the device is powered up. Any idea how to solve this? UPDATE: After stopping the network-manager service, setting up the connection manually and starting the service again, it now detects the ethernet connection. However, the device still can't receive data and doesn't answer to pings. UPDATE 2: As suggested I tried using a cross over cable but the result is exactly the same. However, I found out that connecting the device to the dock (as opposed to directly to the laptop) works fine. I know that the ethernet port in the laptop works fine, because connecting to the network through it works. Is it possible that the port in the laptop doesn't support Gb Ethernet (because that's what the device requires) but the one in the dock does?

  Read the article

• cannot boot ubuntu 13.10 with my usb, Can i change the kernal on my laptop to run it?

  - by Carlos Dunick

  Currently i am running 12.04 and looking for an upgrade to 13.10 I first tried a bootable 64bit usb and failed. With the message saying "Kernal requires an x86-64 CPU but only detected an I686 CPU Unable to boot please use a kernal appropriate for your CPU" then tried 32bit and same message came up. Is this due to my laptop simply being to slow? or can/should i change the kernal somehow? Acer Aspire 5710z Intel Pentium dual core processor, 1.73Ghz, 533 MHz FSB, 1 MB L2 cache. 2GB DDR2 lspci 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) 00:1c.2 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 3 (rev 02) 00:1c.3 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) 00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02) 00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02) 00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02) 04:00.0 Ethernet controller: Broadcom Corporation NetLink BCM5787M Gigabit Ethernet PCI Express (rev 02) 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 06:00.0 FLASH memory: ENE Technology Inc ENE PCI Memory Stick Card Reader Controller 06:00.1 SD Host controller: ENE Technology Inc ENE PCI SmartMedia / xD Card Reader Controller 06:00.2 FLASH memory: ENE Technology Inc Memory Stick Card Reader Controller 06:00.3 FLASH memory: ENE Technology Inc ENE PCI Secure Digital / MMC Card Reader Controller

  Read the article

• Cannot establish ssh connection to computer on local network

  - by ovangle

  I've just (re)installed ubuntu 11.10 on my main pc, and the connection times out every time I try to ssh connect to my laptop (over the local network) to retrieve the files I backed up there. The connection times out every time I try to connect. I can establish a connection in the other direction without issue. Here's the verbose output I get when I try to connect: ovangle@ruby-EP43-DS3:~$ ssh -v [email protected] OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 10.1.1.4 [10.1.1.4] port 22. debug1: connect to address 10.1.1.4 port 22: Connection timed out ssh: connect to host 10.1.1.4 port 22: Connection timed out ssh is installed on both machines, and I've tried deleting '~/.ssh/known_hosts' on both machines, still nada. I've changed the sshd logging on the laptop to VERBOSE and restarted the daemon (because I wasn't getting any relevant syslog entries otherwise), and this is the log for the most recent connection attempt. EDIT: posted wrong logs last time. They just showed that there was a connection received, they weren't actually the sshd logs (which were in auth.log as I recently discovered). Unfortunately, that log is filling up with extremely weird error messages and it gives me no information about the connection. Nov 8 16:02:18 ovangle-A6Rp pkexec: pam_unix(polkit-1:session): session opened for user root by (uid=1000) Nov 8 16:02:18 ovangle-A6Rp pkexec: pam_ck_connector(polkit-1:session): cannot determine display-device Nov 8 16:02:18 ovangle-A6Rp pkexec[6270]: ovangle: Executing command [USER=root] [TTY=unknown] [CWD=/home/ovangle] [COMMAND=/usr/sbin/gnome-power-backlight-helper --set-brightness 2] Nov 8 16:02:19 ovangle-A6Rp pkexec: pam_unix(polkit-1:session): session opened for user root by (uid=1000) Nov 8 16:02:19 ovangle-A6Rp pkexec: pam_ck_connector(polkit-1:session): cannot determine display-device Nov 8 16:02:19 ovangle-A6Rp pkexec[6273]: ovangle: Executing command [USER=root] [TTY=unknown] [CWD=/home/ovangle] [COMMAND=/usr/sbin/gnome-power-backlight-helper --set-brightness 7]

  Read the article

• Battery Life in ubuntu 14.04

  - by user287466

  Today i had fresh installation of ubuntu 14.04 previously i had ubuntu 12.04 and had 5 to 6 hours of battery backup even at constant work, but in 14.04 getting 3 hrs only, tried with tlp but no use. lspci: 0:00.0 Host bridge: Intel Corporation 3rd Gen Core processor DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 3rd Gen Core processor Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) 00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04) 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 02:00.0 Network controller: Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01)

  Read the article

• ??GoldenGate??Manager??

  - by Liu Maclean(???)

  ???????OGG?????????????MGR(Manager)???????,????????./dirprm/mgr.prm???? ????????manager?????: ggsci > edit params mgr ??ggsci edit params???????,???????????? OGG??????????????????????? ???mgr.prm????,??????./dirprm??OGG???????? ???Manager?????????,????????????????????? ????????????????,??????????????????????????????,???????????? PORT 7809 –??MGR?PORT????????,????????TCP?????,?????????????7809?????????? DYNAMICPORTLIST 9101 – 9356DYNAMICPORTSREASSIGNDELAY 5 –???????????source????????,??????target????????? PURGEOLDEXTRACTS ./dirdat/*, usecheckpoints, minkeephours 96 Manager????trail?????????,minkeephours 96????96????4???trail LAGINFOSECONDS 15LAGCRITICALMINUTES 2 ??2??????LAG REPORT????? BOOTDELAYMINUTES 3 ??BOOTDELAYMINUTES??windows??,??Windows??3????BOOT OGG MGR AUTOSTART ER * AUTOSTART ???MGR????????EXTRACT?REPLICAT AutoRestart ER *, WaitMinutes 5, Retries 3 AUTORESTART ?????????OGG??,?????????? PurgeMarkerHistory MinKeepDays 3, MaxKeepDays 7, FrequencyMinutes 120 ??PurgeMarkerHistory?????DDL?????? CHECKMINUTES 10 CHECKMINUTES ??? MGR????????,?????10???? DOWNCRITICAL ?????OGG???abend??????????,?????DOWNCRITICAL??,??????? ??Manager?????????,???????????,manager????????? OGG??????Manager????????????Extract?Replicat?Manager??????,??Manager????????Manager????,????????????????,Refresh???MGR?????????? ??????MGR PARAMS GGSCI (XIANGBLI-CN) 2> view params mgr Port 7809 UserId goldengate, Password goldengate CheckMinutes 10PurgeOldExtracts ./dirdat/*, UseCheckpoints, MinKeepHours 96PurgeMarkerHistory MinKeepDays 3, MaxKeepDays 7, FrequencyMinutes 120AutoRestart ER *, WaitMinutes 5, Retries 3LagInfoMinutes 0LagReportMinutes 10 GGSCI (XIANGBLI-CN) 4> start mgr Manager started.

  Read the article

• glassfish v3.0 hangs no app is ever deployed and no error is ever shown

  - by Samuel Lopez

  I have a web app that uses JSF 2.0 with richFaces and primeFaces, hibernate and java and I use NetBeans 7.1.2 as the IDE when I run the app the glassfish server is started and the log shows this: Launching GlassFish on Felix platform Información: Running GlassFish Version: GlassFish Server Open Source Edition 3.1.2 (build 23) Información: Grizzly Framework 1.9.46 started in: 20ms - bound to [0.0.0.0:4848] Información: Grizzly Framework 1.9.46 started in: 32ms - bound to [0.0.0.0:8181] Información: Grizzly Framework 1.9.46 started in: 59ms - bound to [0.0.0.0:8080] Información: Grizzly Framework 1.9.46 started in: 32ms - bound to [0.0.0.0:3700] Información: Grizzly Framework 1.9.46 started in: 21ms - bound to [0.0.0.0:7676] Información: Registered org.glassfish.ha.store.adapter.cache.ShoalBackingStoreProxy for persistence-type = replicated in BackingStoreFactoryRegistry Información: SEC1002: Security Manager is OFF. Información: SEC1010: Entering Security Startup Service Información: SEC1143: Loading policy provider com.sun.enterprise.security.provider.PolicyWrapper. Información: SEC1115: Realm [admin-realm] of classtype [com.sun.enterprise.security.auth.realm.file.FileRealm] successfully created. Información: SEC1115: Realm [file] of classtype [com.sun.enterprise.security.auth.realm.file.FileRealm] successfully created. Información: SEC1115: Realm [certificate] of classtype [com.sun.enterprise.security.auth.realm.certificate.CertificateRealm] successfully created. Información: SEC1011: Security Service(s) Started Successfully Información: WEB0169: Created HTTP listener [http-listener-1] on host/port [0.0.0.0:8080] Información: WEB0169: Created HTTP listener [http-listener-2] on host/port [0.0.0.0:8181] Información: WEB0169: Created HTTP listener [admin-listener] on host/port [0.0.0.0:4848] Información: WEB0171: Created virtual server [server] Información: WEB0171: Created virtual server [__asadmin] Información: WEB0172: Virtual server [server] loaded default web module [] Información: Inicializando Mojarra 2.1.6 (SNAPSHOT 20111206) para el contexto '/test' Información: Hibernate Validator 4.2.0.Final Información: WEB0671: Loading application [test] at [/test] Información: CORE10010: Loading application test done in 4,885 ms Información: GlassFish Server Open Source Edition 3.1.2 (23) startup time : Felix (1,848ms), startup services(5,600ms), total(7,448ms) Información: JMX005: JMXStartupService had Started JMXConnector on JMXService URL service:jmx:rmi://SJ007:8686/jndi/rmi://SJ007:8686/jmxrmi Información: WEB0169: Created HTTP listener [http-listener-1] on host/port [0.0.0.0:8080] Información: Grizzly Framework 1.9.46 started in: 14ms - bound to [0.0.0.0:8080] Información: WEB0169: Created HTTP listener [http-listener-2] on host/port [0.0.0.0:8181] Información: Grizzly Framework 1.9.46 started in: 12ms - bound to [0.0.0.0:8181] but right there it hangs and the deploy bar keeps running but no more actions are shown, nothing else is logged either it just stays there until I stop the deploy Is there any other error log to debug glassfish server? Any thoughts? I have re installed glassfish and NetBeans but it all seems the same. I think this started happening after I had to force-restart my computer with NetBeans stil open and the app deployed, but it's hard to know for sure if this was the real catalyst. Any thoughts or help is appreciated thanks. Is it an app error? if so why no errors in the log are shown?

  Read the article

• XBRL US Conference Highlights

  - by john.orourke(at)oracle.com

  Back in early November I had an opportunity to attend the XBRL US National Conference in Philadelphia.  At the event, XBRL US announced that Oracle had joined the initiative, so I had a chance to participate in a press conference and attend a number of sessions.  Oracle joined XBRL US so we can stay ahead of the standard and leverage it in our products, and to help drive awareness with customers and improve adoption of XBRL. There were roughly 250 attendees at the event, about half of which were vendors and consultants and the rest financial reporting staff from corporate filers.  Event sponsors included Ernst & Young, SWIFT and Fujitsu.  There were also a number of XBRL technology and service providers exhibiting at the conference.  On Monday Nov. 8th, the XBRL US Steering Committee meetings and Annual Members meeting and reception were held.  At the Annual Members meeting the big news was that current XBRL US President, Mark Bolgiano, is moving to a new position at Howard Hughes Medical Center.  Campbell Pryde, who had led the Taxonomy Development for XBRL US, is taking over as XBRL US President. Other items that were highlighted at the members meeting included: The US GAAP XBRL taxonomy is being used by over 1500 SEC filers and has now been handed over to the FASB to maintain and enhance 16 filer training events were held in 2010 XBRL Global Magazine was launched Corporate Actions proposal was submitted to the SEC with SWIFT in May XBRL Labs for iPhone, XBRL US Consistency Suite launched ISO 2022 Corporate Actions Alignment with XBRL achieved The XBRL Credit Rating taxonomy was accepted Tuesday Nov. 9th included Keynotes, General Sessions, Innovation Workshop for Governments and Securities Professionals, and an Opening Reception.  General sessions included: Lessons Learned from the SEC's rollout of XBRL.  More than 18,000 errors were identified in reviews of filings between June 2009 and September 2010.  Most of these related to negative values being used where they shouldn't have.  Also, the SEC feels there are too many taxonomy extensions being created - mostly in the Cash Flow Statements.  They emphasize using existing elements in the US GAAP taxonomy and advise filers not to  create extensions to improve the visual formatting of XBRL filings. Investors and XBRL - Setting the Standard for Data Quality.  In this panel discussion, the key learning was that CFA's, academics and the financial community are not using XBRL as expected.  The issues raised include the  accuracy and completeness of filings, number of taxonomy extensions, and limited number of tools available to help analyze XBRL data.  Another big issue that was raised is the lack of historic results in XBRL - most analysts need 10 quarters of historic data.  On the positive side, XBRL has the potential to eliminate re-keying of data and errors here and can improve analytic capabilities for financial analysts once more historic data is available and more companies are providing detailed tagging of their filings. A US Roadmap for XBRL Financial Reporting.  This was a panel discussion featuring Jeff Neumann(SEC), Campbell Pryde(XBRL US), and Louis Matherne(FASB).  Key points included the fact that XBRL is currently used by 1500 companies, with 8000 more companies coming in 2011.  XBRL for Mutual Fund Reporting will start in 2011 for 8000 funds, and a Credit Rating Taxonomy has now been submitted for review.  The XBRL tagging/filing process is improving each quarter - more education is helping here.  The FASB is looking at extensions to date, and potential additions to US GAAP taxonomy, while the SEC is evaluating filings for accuracy, consistency in tagging, and tools for analyzing data.  The big news is that the FASB 2011 US GAAP Taxonomy has been completed and reviewed by SEC.  The 2011 US GAAP Taxonomy supports new FASB accounting standards issued since 2009, has new taxonomy elements for certain industries (i.e airlines) and the elimination of 500 concepts.  (meaning they can't be used going forward but are still supported for historical comparison)  The 2011 US GAAP Taxonomy will be available for usage with Q2 2011 SEC filings.  More information about this can be found on the FASB web site.  http://www.fasb.org/home Accounting Firms and XBRL.  This session covered the Role of Audit Firms, which includes awareness and education, validation of XBRL filings, and in-house transition planning.  The main advice provided was that organizations should document XBRL mapping process, perform peer comparisons, and risk assessments on a regular basis. Wednesday Nov. 10th included more Keynotes, General Sessions on Corporate Actions, and XBRL Essentials Workshop Training for corporate filers.  The XBRL Essentials Training included: Getting Started Once you Have the Basics Detailed Footnote Tagging and Handling Tables Quality Control and Trust in the XBRL Process Bringing XBRL In-House:  What are the Options, What should you consider? The US GAAP Financial Reporting Taxonomy - Overview of the 2011 release The XBRL Essentials Training was well-attended with about 80 people.  This included a good overview of the SEC's XBRL mandate, limited liability issue, tagging levels, recommended planning process, internal vs. outsourced approach, and how to manage service providers.  I learned a lot from the session on detailed tagging.  This is the requirement that kicks in during a company's second year of XBRL filing with the SEC and applies to financial statements, footnotes and disclosures (it does not apply to MD&A, executive communications and other information).  The review of the Linkbase model, or dimensional table structure, was very interesting and can be complex to understand.  The key takeaway here is that using dimensional tables in XBRL filings can help limit the number of taxonomy extensions that are required.  The slides from this session are posted on the XBRL US web site. (http://xbrl.us/events/Pages/archive.aspx) For me, the main summary points and takeaways from the XBRL US conference are: XBRL for financial reporting has turned the corner and gone mainstream - with 1500 companies currently using it and 8000 more coming in 2011 The expected value is not being achieved by filers or consumers of XBRL data - this will improve when more companies are filing in XBRL, more history is available, and more software tools are available for analysis (hmm, sounds like an opportunity for Oracle) XBRL is becoming the global standard for all business communications beyond just the financials - i.e. adoption for mutual funds, corporate actions and others planned for the future If you would like to learn more about XBRL and the various training programs, services and software tools that are available check out the XBRL US web site and even better - become a member.  Here's a link:  http://xbrl.us/Pages/default.aspx

  Read the article

• python list mysteriously getting set to something within my django/piston handler

  - by Anverc

  To start, I'm very new to python, let alone Django and Piston. Anyway, I've created a new BaseHandler class "class BaseApiHandler(BaseHandler)" so that I can extend some of the stff that BaseHandler does. This has been working fine until I added a new filter that could limit results to the first or last result. Now I can refresh the api page over and over and sometimes it will limit the result even if I don't include /limit/whatever in my URL... I've added some debug info into my return value to see what is happening, and that's when it gets more weird. this return value will make more sense after you see the code, but here they are for reference: When the results are correct: "statusmsg": "2 hours_detail found with query: {'empid':'22','datestamp':'2009-03-02',}", when the results are incorrect (once you read the code you'll notice two things wrong. First, it doesn't have 'limit':'None', secondly it shouldn't even get this far to begin with. "statusmsg": "1 hours_detail found with query: {'empid':'22','datestamp':'2009-03-02',with limit[0,1](limit,None),}", It may be important to note that I'm the only person with access to the server running this right now, so even if it was a cache issue, it doesn't make sense that I can just refresh and get different results by hitting F5 while viewing: http://localhost/api/hours_detail/datestamp/2009-03-02/empid/22 Here's the code broken into urls.py and handlers.py so that you can see what i'm doing: URLS.PY urlpatterns = patterns('', #hours_detail/id/{id}/empid/{empid}/projid/{projid}/datestamp/{datestamp}/daterange/{fromdate}to{todate}/limit/{first|last}/exact #empid is required # id, empid, projid, datestamp, daterange can be in any order url(r'^api/hours_detail/(?:' + \ r'(?:[/]?id/(?P<id>\d+))?' + \ r'(?:[/]?empid/(?P<empid>\d+))?' + \ r'(?:[/]?projid/(?P<projid>\d+))?' + \ r'(?:[/]?datestamp/(?P<datestamp>\d{4,}[-/\.]\d{2,}[-/\.]\d{2,}))?' + \ r'(?:[/]?daterange/(?P<daterange>(?:\d{4,}[-/\.]\d{2,}[-/\.]\d{2,})(?:to|/-)(?:\d{4,}[-/\.]\d{2,}[-/\.]\d{2,})))?' + \ r')+' + \ r'(?:/limit/(?P<limit>(?:first|last)))?' + \ r'(?:/(?P<exact>exact))?$', hours_detail_resource), HANDLERS.PY # inherit from BaseHandler to add the extra functionality i need to process the possibly null URL params class BaseApiHandler(BaseHandler): # keep track of the handler so the data is represented back to me correctly post_name = 'base' # THIS IS THE LIST IN QUESTION - SOMETIMES IT IS GETTING SET TO [0,1] MYSTERIOUSLY # this gets set to a list when the results are to be limited limit = None def has_limit(self): return (isinstance(self.limit, list) and len(self.limit) == 2) def process_kwarg_read(self, key, value, d_post, b_exact): """ this should be overridden in the derived classes to process kwargs """ pass # override 'read' so we can better handle our api's searching capabilities def read(self, request, *args, **kwargs): d_post = {'status':0,'statusmsg':'Nothing Happened'} try: # setup the named response object # select all employees then filter - querysets are lazy in django # the actual query is only done once data is needed, so this may # seem like some memory hog slow beast, but it's actually not. d_post[self.post_name] = self.queryset(request) # this is a string that holds debug information... it's the string I mentioned before pasting this code s_query = '' b_exact = False if 'exact' in kwargs and kwargs['exact'] <> None: b_exact = True s_query = '\'exact\':True,' for key,value in kwargs.iteritems(): # the regex url possibilities will push None into the kwargs dictionary # if not specified, so just continue looping through if that's the case if value == None or key == 'exact': continue # write to the s_query string so we have a nice error message s_query = '%s\'%s\':\'%s\',' % (s_query, key, value) # now process this key/value kwarg self.process_kwarg_read(key=key, value=value, d_post=d_post, b_exact=b_exact) # end of the kwargs for loop else: if self.has_limit(): # THIS SEEMS TO GET HIT SOMETIMES IF YOU CONSTANTLY REFRESH THE API PAGE, EVEN THOUGH # THE LINE IN THE FOR LOOP WHICH UPDATES s_query DOESN'T GET HIS AND THUS self.process_kwarg_read ALSO # DOESN'T GET HIT SO NEITHER DOES limit = [0,1] s_query = '%swith limit[%s,%s](limit,%s),' % (s_query, self.limit[0], self.limit[1], kwargs['limit']) d_post[self.post_name] = d_post[self.post_name][self.limit[0]:self.limit[1]] if d_post[self.post_name].count() == 0: d_post['status'] = 0 d_post['statusmsg'] = '%s not found with query: {%s}' % (self.post_name, s_query) else: d_post['status'] = 1 d_post['statusmsg'] = '%s %s found with query: {%s}' % (d_post[self.post_name].count(), self.post_name, s_query) except: e = sys.exc_info()[1] d_post['status'] = 0 d_post['statusmsg'] = 'error: %s' % e d_post[self.post_name] = [] return d_post class HoursDetailHandler(BaseApiHandler): #allowed_methods = ('GET',) model = HoursDetail exclude = () post_name = 'hours_detail' def process_kwarg_read(self, key, value, d_post, b_exact): if ... # I have several if/elif statements here that check for other things... # 'self.limit =' only shows up in the following elif: elif key == 'limit': order_by = 'clock_time' if value == 'last': order_by = '-clock_time' d_post[self.post_name] = d_post[self.post_name].order_by(order_by) # TO GET HERE, THE ONLY PLACE IN CODE WHERE self.limit IS SET, YOU MUST HAVE GONE THROUGH # THE value == None CHECK???? self.limit = [0, 1] else: raise NameError def read(self, request, *args, **kwargs): # empid is required, so make sure it exists before running BaseApiHandler's read method if not('empid' in kwargs and kwargs['empid'] <> None and kwargs['empid'] >= 0): return {'status':0,'statusmsg':'empid cannot be empty'} else: return BaseApiHandler.read(self, request, *args, **kwargs) Does anyone have a clue how else self.limit might be getting set to [0, 1] ? Am I misunderstanding kwargs or loops or anything in Python?

  Read the article

• Static Javascript files not loaded in Express app

  - by Dave Long

  I have an express app that has a bunch of static javascript files that aren't being loaded even though they are registered in my app.js file. Even public scripts (like jQuery: http://ajax.googleapis.com/ajax/libs/jquery/1.6.3/jquery.min.js) aren't processing. I can see the script tags in the generated html, but none of the functionality runs and I can't see the files loading in the web inspector. Here is the code that I have: app.js var express = require('express') var app = module.exports = express.createServer(); // Configuration var port = process.env.PORT || 3000; app.configure(function(){ app.set('views', __dirname + '/views'); app.set('view engine', 'jade'); app.use(express.bodyParser()); app.use(express.methodOverride()); app.use(app.router); app.use(express.static(__dirname + '/public')); }); app.configure('development', function(){ app.use(express.errorHandler({ dumpExceptions: true, showStack: true })); }); app.configure('production', function(){ app.use(express.errorHandler()); }); // Routes app.get('/manage/new', function(req, res){ res.render('manage/new', { title: 'Create a new widget' }); }) app.listen(port); console.log("Express server listening on port %d in %s mode", app.address().port, app.settings.env); /views/manage/layout.jade !!! 5 html(lang="en") head title= title link(rel="stylesheet", href="/stylesheets/demo.css") link(rel="stylesheet", href="/stylesheets/jquery.qtip.css") script(type="text/javascript", href="http://ajax.googleapis.com/ajax/libs/jquery/1.6.3/jquery.min.js") body!= body script(type="text/javascript", href="/javascripts/jquery.formalize.js") script(type="text/javascript", href="/javascripts/jquery.form.js") script(type="text/javascript", href="/javascripts/jquery.qtip.js") script(type="text/javascript", href="/javascripts/formToWizard.js") script(type="text/javascript", href="/javascripts/widget.js") /views/manage/new.jade h1= title div(style="float:left;") form(action="/manage/generate", method="post", enctype="multipart/form-data", name="create-widget") .errors fieldset legend Band / Album Information fieldset legend Social Networks fieldset legend Download All of my javascript files are stored in /public/javascripts and all of my static CSS files are being served up just fine. I'm not sure what I've done wrong.

  Read the article

• Form data sent to Node via Post is undefined

  - by user185812

  I know this has been asked countless times on here, however I tried all the solutions and am still having the issue. Most people say to set the content-type (which I did) and to name the inputs that I wish to Post to node. I have done both of these things, yet still get "undefined" when trying to send data from an HTML form to node. JADE Templating HTML Code (Sorry I can't seem to get the indenting to show up here, however I think I should leave the code intact when posting here instead of converting it to normal HTML so that if the error is in here, you are still able to help) Form(action="/registration", method="post", enctype="application/x-www-form-urlencoded") div(class="control-group-Username") label(class="control-group", for="username") Username: div.controls input#Username(id="Username", type="text", placeholder="Username Here", maxlength="23", name="username") //Other divs and stuff here button.btn#submit_button(type="submit") Submit app.js code /** * Module dependencies. */ express = require('express') , routes = require('./routes') , user = require('./routes/user') , http = require('http') , path = require('path'); app = express(); // all environments app.set('port', process.env.PORT || 3000); app.set('views', __dirname + '/views'); app.set('view engine','jade'); app.use(express.favicon()); app.use(express.logger('dev')); app.use(express.bodyParser()); app.use(express.methodOverride()); app.use(express.cookieParser('your secret here')); app.use(express.session()); app.use(app.router); app.use(require('less-middleware')({ src: __dirname + '/public' })); app.use(express.static(path.join(__dirname, 'public'))); // development only if ('development' == app.get('env')) { app.use(express.errorHandler()); } app.use(express.static(__dirname + '/public')); app.get('/', routes.index); app.get('/users', user.list); app.get('/register', routes.register); http.createServer(app).listen(app.get('port'), function(){ console.log('Express server listening on port ' + app.get('port')); }); require('./Register.js'); register.js code app.post('/registration', function(req, res) { var Email=req.body.username console.log(username); });

  Read the article

• Given a trace of packets, how would you group them into flows?

  - by zxcvbnm

  I've tried it these ways so far: 1) Make a hash with the source IP/port and destination IP/port as keys. Each position in the hash is a list of packets. The hash is then saved in a file, with each flow separated by some special characters/line. Problem: Not enough memory for large traces. 2) Make a hash with the same key as above, but only keep in memory the file handles. Each packet is then put into the hash[key] that points to the right file. Problems: Too many flows/files (~200k) and it might run out of memory as well. 3) Hash the source IP/port and destination IP/port, then put the info inside a file. The difference between 2 and 3 is that here the files are opened and closed for each operation, so I don't have to worry about running out of memory because I opened too many at the same time. Problems: WAY too slow, same number of files as 2 so also impractical. 4) Make a hash of the source IP/port pairs and then iterate over the whole trace for each flow. Take the packets that are part of that flow and place them into the output file. Problem: Suppose I have a 60 MB trace that has 200k flows. This way, I would process, say, a 60 MB file 200k times. Maybe removing the packets as I iterate would make it not so painful, but so far I'm not sure this would be a good solution. 5) Split them by IP source/destination and then create a single file for each one, separating the flows by special characters. Still too many files (+50k). Right now I'm using Ruby to do it, which might've been a bad idea, I guess. Currently I've filtered the traces with tshark so that they only have relevant info, so I can't really make them any smaller. I thought about loading everything in memory as described in 1) using C#/Java/C++, but I was wondering if there wouldn't be a better approach here, especially since I might also run out of memory later on even with a more efficient language if I have to use larger traces. In summary, the problem I'm facing is that I either have too many files or that I run out of memory. I've also tried searching for some tool to filter the info, but I don't think there is one. The ones I've found only return some statistics and wouldn't scan for every flow as I need.

  Read the article

• Naming selenium grid nodes. Spawning a specific node

  - by ???? ????

  I'm trying to implement a kind of default queues in selenium hub. There is a possibility to specify node's name (actually its environment, smth like "firefox on ubuntu" or "chrome on windows"). Selenium grid itself has a default queue, it works according to 'First In, First Out' principle. But I want to prioritize some of my tasks given to selenium server. I have no possibility to introduce custom queue (seems like there is no API for that), that's why I decided to separate queue's logic from selenium server. I'll only call a specific node with specific name (environment) for example "firefox important node" or smth like that. So, I want to know how to directly tell selenium which node to use for my task? And generally, am I thinking in a right way? Here are my configs: hubConfig.json.erb { "host": null, "port": <%= node[:selenium][:server][:port] %>, "newSessionWaitTimeout": -1, "servlets" : [], "prioritizer": null, "capabilityMatcher": "org.openqa.grid.internal.utils.DefaultCapabilityMatcher", "throwOnCapabilityNotPresent": true, "nodePolling": <%= node[:selenium][:server][:node_polling] %>, "cleanUpCycle": <%= node[:selenium][:server][:cleanup_cycle] %>, "timeout": <%= node[:selenium][:server][:timeout] %>, "browserTimeout": 0, "maxSession": <%= node[:selenium][:server][:max_session] %> } nodeConfig.json.erb { "capabilities": [ { "browserName": "firefox", "maxInstances": 5, "seleniumProtocol": "WebDriver" }, { "browserName": "chrome", "maxInstances": 5, "seleniumProtocol": "WebDriver" }, { "browserName": "phantomjs", "maxInstances": 5, "seleniumProtocol": "WebDriver" } ], "configuration": { "proxy": "org.openqa.grid.selenium.proxy.DefaultRemoteProxy", "maxSession": <%= node[:selenium][:node][:max_session] %>, "port": <%= node[:selenium][:node][:port] %>, "host": "<%= node[:fqdn] %>", "register": true, "registerCycle": <%= node[:selenium][:node][:register_cycle] %>, "hubPort": <%= node[:selenium][:server][:port] %> } } And my Driver class: ... def remote_driver @browser = Watir::Browser.new(:remote, :url => "http://myhub.com:4444/wd/hub", :http_client => client, :desired_capabilities => capabilities ) end def capabilities Selenium::WebDriver::Remote::Capabilities.send( "firefox", :javascript_enabled => true, :css_selectors_enabled => true, :takes_screenshot => true ) end def client client = Selenium::WebDriver::Remote::Http::Default.new client.timeout = 360 client end ... I still don't know how to use specified node for my task. If I try to start a driver adding :name => "firefox important node" and extend nodeConfig.json.erb's configuration with environments: - name: "firefox important node" browser: "*firefox" - name: "Firefox36 on Linux" browser: "*firefox" selenium just starts random firefox browser on a random node. How can I control it?

  Read the article

< Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >