Search Results

Search found 6079 results on 244 pages for 'power law'.

Page 151/244 | < Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >

• Remote access not working without connected monitor

  - by winSharp93

  I am trying to configure a Windows Server 2008 as a Home Server for my personal use (mainly for storing documents, hosting source-control, etc.). The "server" consists of an Intel Atom 2700DC board and an Intel SSD. Configuring remote access to the server, I am confronted with a very strange problem: As long as a monitor is connected to my server, remote access works without any problems. However, when no monitor is connected at boot-time, remote access simply won't work (I keep getting errors when trying to connect that the remote server was not found or that remote access is disabled). Windows definitely boots when no monitor is connected as I receive a message asking me whether to enter safe mode when booting after powering the server down by plugging the power cord. When I plug in a monitor after boot, it stays turned off and remote desktop connections still fail. Do you have any ideas about what I could try?

  Read the article

• HP ML150 G6 upgrading RAM/CPU beyond specs?

  - by Morten Green Hermansen

  I am being told that some limits on some HP servers can be crossed. Do any of you have any experience with that? A ML150/G6 is limited to 48GB RAM but I have been talking to a German company that guaranties me that this server will be able to be upgraded to 384GB RAM (using 32GB memory modules and 2 CPUs) http://www.compuram.de/en/memory,HP+%28-Compaq%29,Server,Proliant,ML150+G6.htm Can this really be true? The server that I have is using E5504 CPUs but will I be able to upgrade to any CPU that is using a LGA1366 socket? All from a low wattage L5640 all the way to the 6 core, high wattage versions like an X5650? (If cooling and power is adequate ofcause). Is there any limitation with powerregulators and chipset (Intel 5500). I am looking forward to any reply. Thanks in advance and best regards, - Morten Green Hermansen, Fanitas

  Read the article

• Issue with Toshiba Satellite C50 A-1JM

  - by Nathan Hawkes

  I am having some odd problems with my Toshiba laptop. For the last two days, it has not loaded past the boot screen for hours, if at all. When I force the laptop off and switch it back on, it goes to the Preparing Automatic Repair process but will not complete the process and go to the desktop. However, this only happens when the battery is plugged in. When I remove the battery and run the laptop on power, it works without issue. Would this be a battery issue (given it works without the battery) or a hard drive issue (given it won't get past the boot screen)? If neither, what would you suggest as a solution?

  Read the article

• Difficulty racking Proliant G8's

  - by Systemspoet

  We're an all Proliant shop with around 50 servers, mostly DL360s and DL380, from G5's through G7's. We just got our first two G8's in and went to rack them. We were stunned to find out that the new cable management arms protrude almost 1 inch deeper into the rack then previous iterations of the Proliant line. Unfortunately that causes them to occupy the same space as the PDU's in our APC racks. In a non-densely populated section of rack that's no biggie, but in a densely populated section it's impossible to get the cable arm into place without dislodging another machine's power. Has anyone else run into this? Obviously racking machines without cable management arms is not an option. I supposed we could reconfigure our racks but that's a nightmare.

  Read the article

• Multiple Graphics cards - Non Multi-Display Setup

  - by Alan Thomas

  Is it possible for me to utilize the processing capabilities of multiple graphics cards, even if I'm only using one monitor? I recently bought a new AMD graphics card, fairly top of the line. I also have a two year old, decent nVidia card. They're obviously very different cards. I don't really mind for gaming because my current card can handle most games fine by itself. I'm concerned about video editing programs such as Adobe Premiere and After Effects. Would the system be able to utilize the power of both cards to, say, render a video? I have both drivers still installed on my machine. And because there is only one monitor connected to my current graphics card (AMD) the nVidia would be connected to no display. So I am wondering whether it would or could be utilized in some way to help in processing video. Thanks!

  Read the article

• Lost contact with my NAS after changing its IP

  - by Beles

  I did some brain-dead reconfiguring of my D-Link DNS-323 NAS some days ago. I have a home network where each computer gets a dynamically allocated IP address starting at 192.168.1.100. The irritating point (for me at least) was that the NAS changed IP if the power went down or I turned off the router. I then had to remap a drive-letter to point to the new IP address of the NAS. To remedy that I configured the NAS to have a static IP, 192.168.0.10. I had no good reason to choose that IP, other than I found it in a user manual for the NAS. After I changed the IP and rebooted the NAS it disappeared from the network and was never to be found again. Now I have a black brick standing in my home, looking good, but "dead". Could anyone point me in a direction which helps me solve this problem? I have about 100gb worth of pic of my children on this brick so I really want it back :-) Sincerely,

  Read the article

• "Disk Not Found" Error when trying to install iso image of CentOs on ESXI using VSphere

  - by kamal

  When trying to install CentOs setup as an iso image on datastore, i get an error : "Disk Not Found". I am using ESXi 4.1 as host VM. Is there a way to attach DVD/CD as iso image ? I tried "Connect at Power on" Checked and Connect CD/DVD on the VSphere Console, but i still am unable ot get the iso image recognized as a DVD mounted image: Solved: if i look at the image size, it was 11 MB, so it WAS a boot iso, but nithing else, if we compare it with other boot images with complete iso's therein lies the solution. This boot.iso was from rBUILD/Conary packaging

  Read the article

• BGP Router reccomendations for simple redundancy [closed]

  - by Jona

  We have two sites that each have an internet connection and have a dedicated dark fibre between them. Each site has it's own IP space and we have an AS number. We're looking to be resilient to failure of the internet connection to either site and so need to buy a pair of approriate routers. Requirements are: Able to run 2 bgp sessions (one with the ISP, one with the other site router) Option to take a full table from the upstream ISPs would be nice. Able to provide HA gateways on the LAN side (e.g. 192.168.0.254 will automatically migrate if it's host router lost power) A dedicated device rather than a server running Linux / BSD Not crazy expensive. Any help / advice much appreciated.

  Read the article

• Archive Outlook mail items into SQL Server

  - by marc_s

  I am looking (and so far not finding any) for a solution to archive e-mail items from my Outlook into SQL Server. My PST is beginning to get really really big, and I'd love to extract my older e-mail into SQL Server in a way so I can still easily find mails if needed. I would prefer SQL Server as the storage medium since I'm familiar with it, and it's rock solid - I don't want to have a collection of PST files or CHM files or anything like that. Does anyone know of such a solution? I'm a power/home user - I can't afford $5'000 enterprise licenses - I need a sub-$100 solution for private use.

  Read the article

• Areca 1880ix RAID hangs

  - by Dave

  Areca RAID controller ARC-1880ix-12 (firmware 1.50) hangs when on high load. My setup is: Chenbro 3U chassis Intel S5500BC mainboard Xeon 5603 CPU 16GB of RAM 12 Seagate SAS drives ST32000645SS (2 of them as hot spare, 10 as RAID10) Mellanox Infiniband HBA card This server is working as external infiniband storage for Xen VMs. When load is quite big Areca's firmware hangs - it becomes unreachable even from Areca's ethernet adapter. After resetting the server power it returns to normal operation. While Areca is hanged I can confirm that it is powered (ethernet link is active) and Infiniband HBA works Ok. Thanks in advance for any idea or suggestion where the problem might be!

  Read the article

• In general, do 3rd-party laptop AC adapters / chargers work reliably?

  - by MGOwen

  The AC adapters for my 2 dell laptops wore out very quickly. One supplies power but won't charge the battery (it's about 3 years old, the other is a bit newer). Both have worn through to the shielding around the notebook connector and look like they'll be unusable soon. Checking user reviews of the replacement adapter on Dell's own website, it appears they usually fail this fast. Apparently Dell does this deliberately to make money (their adapters sell for about 10-15 times what they cost to make). Same with replacement batteries. I can see there are plenty of much cheaper ($50 less) compatible AC adapters on eBay. Does anyone have experience with these? Naturally I'm nervous a crappy knock-off could fry my notebook, but has this ever actually happened to anyone recently? Has anyone had a good experience? Can anyone recommend a good online seller (who doesn't charge nonsensical shipping costs to Australia, preferably?)

  Read the article

• Windows server 2008 UPS support

  - by Rory McCune

  I'm looking to set-up a UPS on a Windows Small Business Berver 2k8 and I've noticed that there are some large price differences for similar capacity in-line UPSs. The most important point for me in UPS selection is that the server should have the ability to shut itself down before the UPS power runs out, so that if the server is unattended during the outage, it should minimize the risk of data loss. From some reading it appears that Windows Server 2008 should has the ability to natively recognise a UPS, which can then be managed through the battery settings on the server or via WMI. What I'm wondering if anyone know is, Is Windows 2008 servers UPS support specific to certain brands of UPS (eg, APC) or is it likely to work with any UPS which has a USB port, which I can connect to the server?

  Read the article

• Does laser printer use toner when switched on/off?

  - by Alan Harris-Reid

  I have recently purchased a HP LaserJet M175nw laser printer which goes into sleep-mode after 10 minutes of non-use. I know sleep-mode uses a very small amount of power, but the flashing light on the control panel is driving me nuts! I know I can turn-off the printer via. the on/off button, but when it is turned-on manually, there is some whirring sound which I guess might be the machine warming-up. My question is... Is any toner used during this warm-up (or cleaning) cycle? Am I better-off keeping the printer in sleep mode, or is it ok to turn off manually? TIA Alan

  Read the article

• Where should I plug in my monitor -- Motherboard or Graphics card?

  - by Jeremy White

  Assuming I am using the following equipment... motherboard with HDMI/DVI & no embedded graphics discrete graphics card (nVidia or ATI) on PCI-E slot Intel CPU with integrated graphics ...where should I plug my monitor into the computer? Presumably, I'll get the fastest speed on games connected directly to the graphics card. But there is also power savings when connecting to the motherboard and accessing the Intel on-board graphics. I've read that some motherboards can switch automatically between the Intel graphics and discrete graphics. Is that something that works well, and where do I connect the monitor to enable that?

  Read the article

• Hard Drive Fundamentals And Verifying Disk Performance

  - by Agnel Kurian

  Over the past few months, my Windows XP machine has slowed down to a crawl. It takes about 10-15 minutes to go from power-up to reaching a responsive state. I have reasons to believe that this is a result of the hard disk slowing down. Questions: Do hard disks slow down as a result of mechanical wear and tear ...or age? How do I check if my disk has slowed down? Conversely, how can I verify that my disk is indeed running at the speed it's designed to run at? Could drivers be at fault here? Do hard disks come with drivers or does Windows use a generic driver?

  Read the article

• Windows XP not able to boot after loading isapnp.sys driver

  - by pragadheesh

  Hi When i power on my DELL Latitude E6400 laptop running on Windows XP SP3, i get a black screen and hangs after that. So I tried to boot through safe mode which hangs after loading the driver isapnp.sys. Doing a bit of googling i found out Windows XP not booting up including safe mode So I loaded my XP boot cd and tried Recovery Console. In the Recovery console, doing "dir" gives the error "an error occurred during directory enumeration". Then i tried chkdsk /p /r which gave "the volume appears to contain one or more unrecoverable problems" How can i fix these please. Thanks in advance.

  Read the article

• What does an ACPI BIOS configure during boot?

  - by RJSmith92

  When a PC boots with an ACPI BIOS, what does it exactly do? I understand that the point of ACPI is to allow the OS to control hardware resources and power management but before the OS is loaded does ACPI configure just the devices needed to boot and then let the OS configure the rest? If the OS wants to re-asign hardware resources does it store this information in the ACPI tables so that the next time the system is booted it assigns them how the OS wants? The ACPI driver asks the PCI bus driver (Pci.sys) to enumerate devices on it's bus once the OS is loaded, how are these devices configured whilst the PC is booting when it doesn't have other bus drivers? Any help with any of the above questions would be greatly appreciated. Thanks.

  Read the article

• Wake computer from sleep/standby without BIOS support for WOL?

  - by jjeaton

  Just bought a new home server and the nice folks at HP disabled the Wake-On-Lan feature in my motherboard. Are there any other options for waking the computer from Sleep/Standby mode? I'd like to take advantage of power savings wherever I can. I realize that I won't be able to wake it from shutdown, short of putting together some Rube Goldberg machine. EDIT: I'd like to be able to wake the machine on demand, remotely. So I can then RDP into it, or access files, etc.

  Read the article

• Exporting a VM running as a Domain Controller

  - by AndyM

  There is a Microsoft KB article that talks about best practices for running a DC on a VM. One of the notes is "Do not use the Export feature on a virtual machine that is running a domain controller". In order to export a VM, the VM needs to be turned off. If you turn off a DC VM, export it, import it on another server and then power the VM back on, there should be no risk as long as the original (exported) VM is never powered back on. Can someone explain to me why this isn't supported? After doing some searching on Google, the sites I found just regurgitated this line from the KB article, but didn't offer any explanation as to why this isn't supported.

  Read the article

• Unable to diagnose Windows 7 lockup

  - by Delyan

  Basic info: Laptop Dell Studio XPS 13 (Intel P9600, 4GB RAM, NVidia 9400M card, 256G Samsung PM800 SSD) Windows 7 Ultimate, as well as Fedora 14 Here's the deal - Windows would just lock up out of nowhere, no log entries, no dumps, no BSOD, it just freezes. This happens mostly when idle (but it happened when I was using it too) and does not follow a concrete time frame. No input is accepted - only solution is to hold the power button. Although this sounds like a clean cut hardware issue, the reason I'm willing to rule this out is that my primary OS is Fedora 14. It's been working fine for the past 2 years and I've been stress testing the hardware (intentionally or not) every once in a while with no issues. I would like to ask if there's any way to get a diagnostic output from Windows in a situation such as this. The next step in my testing is to leave it in Safe Mode overnight and see if it locks up but even if I do that, I still need to figure out what component freezes it up during normal operation.

  Read the article

• How to charge an iPhone on a Windows PC without Installing iTunes

  - by Martin Hollingsworth

  I want to be able to charge my iPhone on my work computer, which is running Windows Server 2008 SP1 64-Bit. When I plug the iPhone in with the USB cable, it will not charge. Windows attempts to locate a driver for the device but only comes up with a generic Camera device and even if I allow that to be installed, the iPhone still does not charge. I have checked the computer's BIOS settings and did not find anything relating to power on the USB devices. I also tried this on ports at the back of the computer in addition to those on the front. The PC is a Dell Optiplex 780. As far as I can tell USB devices do not charge unless Windows has installed an appropriate driver. Since it is a work computer I do not want to install iTunes which does include a driver. I have a workaround that I will post as an answer for reference.

  Read the article

• Problem accessing MICROSOFT##SSEE database (Error: 18456, Severity: 14, State: 16.)

  - by Philipp Schmid

  After an unexpected server shutdown due to a power failure, I can no longer connect to the internal windows database MICROSOFT##SSEE which is hosting Central Admin for my SBS 2008 server. The log shows: Error: 18456, Severity: 14, State: 16. Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. [CLIENT: <named pipe>] I've tried to connect using the SQL Management studio (connecting to .pipemssql$microsoft##sseesqlquery) but no luck. The SQL Server Configuration Manager doesn't show a entry for 'Protocols for MICROSOFT##SSEE' (but shows it for 2 other database hosted on the same SQL server 2005 Express edition. I have tried to restore the master.ldf and mastlog.log files from a backup, but the issue persists.

  Read the article

• Windows undetectable after interrupted chkdsk

  - by Felthragar

  I have a computer that is running Windows XP. For some reason, the other day it wouldn't start giving me the following message: "ntoskrnl.exe is missing or corrupt" So I put the XP disc in the tray and fired up the repair console and ran the following: chkdsk /r It was on for about eight hours and it got to about 52% I believe. Then there was a power outage and the computer shut down (obviously). Today when I was booting it, it isn't even detecting there's an OS anymore. If I boot the computer with no cd in the tray it says: "Reboot and select a proper Boot device or Insert Boot Media in selected Boot device and press a key" If I run the repair console, or the xp installation program it isn't finding any OS installations. Any ideas on what to do next? Any help is appreciated. Thanks! Update: After turning boot-time diagnostics on, I got this message when booting without cd (instead of the previous one): "Couldn't open drive multi(0)disk(0)rdisk(0)partition(2)"

  Read the article

• Android tethering via bluetooth keeps disconnecting

  - by Ian

  I'm currently using a Google Nexus tablet tethered via Bluetooth to a Samsung S3 for internet. Two things are annoying me. First, if I take the phone away from the tablet (go out for lunch), the tablet disconnects and has to be manually reconnected. Is there a way to have that happen automatically? Second, Bluetooth tethering, i.e. the internet sharing part needs to be switched on each time the bluetooth is switched on (or perhaps just after power cycling) on the S3. Is there no way to have that default to on? Thanks

  Read the article

• Unresponsive virtual OS

  - by confusedGeek

  Hopefully someone has a suggestion on how to resolve this. Configuration Host: Win 2003R2 w/Virtual Server 2005R2 Virtual1: Win 2003R2 w/Sql Server 2005 Virtual2: Win 2003R2 w/WSS 3.0 Situation This past weekend the power went out and took down the servers (no UPS, it's a desktop standing in as dev testing server). Since the servers went down the Virtual2 server after running WSS fairly heavily for an hour to two will become unresponsive via HTTP. If I login via virtual server's remote control I don't get anything beyond a background screen. The CPU counter on the virtual server's master status shows that it isn't doing anything. The only thing I have been able to do is to turn off Virtual2, which loses any state changes. Shutdown commands issue from the virtual server master status are ignored. After restarting Virtual2 the event logs and application logs don't indicate what caused the problem. Anyone have an idea as to how to repair the OS, or maybe what could be the problem? Thanks ahead of time.

  Read the article

< Previous Page | 147 148 149 150 151 152 153 154 155 156 157 158  | Next Page >