Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 156/391 | < Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >

  • IP alias lost when changing main IP

    - by rmflow
    my /etc/network/interfaces: auto eth0 iface eth0 inet static address 192.168.3.75 netmask 255.255.255.0 gateway 192.168.3.0 Situation 1: After linux booted I set an IP alias: ifconfig eth0:0 192.168.3.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.3.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 is lost! Situation 2: After linux booted I set an IP alias: ifconfig eth0:0 192.168.4.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.4.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 stays! How do I properly change main IP, so all my aliases are not lost?

    Read the article

  • internet disconnects

    - by Smokezzaj
    Internet disconnects and reconnects, computer is in a peer to peer workstation with two other computers XP o/s. Only one computer has this problem the other two don't disconnect. Computer's connect to switch no router is being used. Ipconfig shows a DHCP connection, local area connection status shows packets being sent out but packets are not being received or being received at a extremely slow rate. Tried Winstock tool, reinstalling network card driver, restored to previous date, checked ethernet cable and release/renew IP.

    Read the article

  • Why do the IP addresses randomly change?

    - by GiddyUpHorsey
    I have a network with the following: Cable modem with static IP address Router Desktop - Win 7 VM Host - VMware ESXi 4.0 A couple of VM Guests - Windows Every now and then my Win 7 PC is unable to access some of the VMs. When I ping the VMs by their domain name their IP address shows up as the IP address of the cable modem. Sometimes I can fix it by running ipconfig /flushdns. The IP address will reset back to what it was supposed to be, but occasionally it wont work. Why does this happen and how can I fix it?

    Read the article

  • Cisco SA520 to Adtran 1234 no DHCP transfer

    - by Grico
    I am trying to set up a Cisco SA520 to run DHCP on my network. I have a vendor provided switch, the Adtran 1234, and it provides DHCP for our phone systems on VLAN 200. I do not have access to the Adtran, but the vendor gave me a IP on port 1 for WAN and said port 2 should be for the "trust" side should go. I did setup a mini lab where, Adtran 1 went to SA520 WAN port, and SA520 trust 1 went to my laptop. Everything worked fine, I could ping and get internet using the DHCP scope I put on the SA520. I then unplugged my computer from SA520 trust 1 and plugged it into Adtran 2. I plugged my computer into Adtran 23 and I dont get DHCP or even a link light. If I restart my machine, I get a brief link and then it dies once the machine boots. I have tried several ports on the Adtran and none seem to work. Different cables as well. However, when I plug a phone into the Adtran, the phone boot immediately and shows link. Thoughts?

    Read the article

  • Cannot access a very specific site from my router

    - by DJDarkViper
    This is a problem for me because this site is important to me. It's MY website. And sadly my email is hosted on my site (which I cant access either) When I try to access my website when connected to my Linksys E3000 router, these days it simply just doesn't go through. When I ping it, its all Request Timed Out, and when I tracert C:\Users\Kyle>tracert blackjaguarstudios.com Tracing route to blackjaguarstudios.com [199.188.204.228] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms CISCO26565 [192.168.1.1] 2 16 ms 15 ms 11 ms 11.4.64.1 3 11 ms 9 ms 11 ms rd1cs-ge1-2-1.ok.shawcable.net [64.59.169.2] 4 20 ms 21 ms 22 ms 66.163.76.98 5 37 ms 36 ms 35 ms rc1nr-tge0-9-2-0.wp.shawcable.net [66.163.77.54] 6 112 ms 84 ms 85 ms rc2ch-pos9-0.il.shawcable.net [66.163.76.174] 7 86 ms 89 ms 90 ms rc4as-ge12-0-0.vx.shawcable.net [66.163.64.46] 8 90 ms 84 ms 85 ms eqix.xe-3-3-0.cr2.iad1.us.nlayer.net [206.223.115.61] 9 97 ms 97 ms 99 ms xe-3-3-0.cr1.atl1.us.nlayer.net [69.22.142.105] 10 128 ms 128 ms 126 ms ae1-40g.ar1.atl1.us.nlayer.net [69.31.135.130] 11 101 ms 97 ms 96 ms as16626.xe-2-0-5-102.ar1.atl1.us.nlayer.net [69.31.135.46] 12 100 ms 97 ms 197 ms 6509-sc1.abstractdns.com [207.210.114.166] 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 * * * Request timed out. 17 * * * Request timed out. 18 * * * Request timed out. 19 * * * Request timed out. 20 * * * Request timed out. 21 * * * Request timed out. 22 * * * Request timed out. 23 * * * Request timed out. 24 * * * Request timed out. 25 * * * Request timed out. 26 * * * Request timed out. 27 * * * Request timed out. 28 * * * Request timed out. 29 * * * Request timed out. 30 * * * Request timed out. Trace complete. C:\Users\Kyle> SHAW Cable being my ISP. Figuring this was all something to do with some setting I made on the router, I reset the thing back to factory defaults. Nope. So I'm at a bit of a loss what to do here, as NO device (Computers, Laptops, Tablets, Phones, PS3/ 360, etc) can access my site or its features, so it's not just my computer either. But every other site is just fine. When I connect to my neighbors router, the site comes up just fine. And shes with SHAW as well. What should I do?!

    Read the article

  • Windows 7 and Vista Home Networked-Unable to login from Vista to Windows 7

    - by Lynn
    I set up both Vista and Windows 7 on the same workgroup. I can view Windows 7 from Vista and vice versa. I can login into Vista from Windows 7. I am unable to login to Windows 7 from Vista. When I enter the Windows 7 User name and Password on Vista, the following information appears: Logon unsuccessful: Windows is unable to log you on. Be sure that your user name and password are correct. Both are correct. Do you have any idea how I can resolve this logon issue? Thank you, Lynn

    Read the article

  • connect server to server on secondary NIC

    - by microchasm
    Hi, I have a CentOS box with multiple NIC's running Apache. I also have another box running RHEL that will be the MySQL server. I'm trying to use the secondary NIC on the Apache box to connect directly to the MySQL server, but so far no luck. I want to isolate the MySQL box as much as possible which is why I'm going for a direct connection as opposed to running through a switch. I have a crossover cable running between them. IP configs: Apache box eth0 [to lan] ip addr: 192.168.200.100 netmask: 255.255.0.0 gateway: 192.168.111.1 eth1 [to mysql] ip addr: 192.168.200.101 netmask: 255.255.0.0 gateway: [blank] MySQL box eth0 [to apache] ip addr: 192.168.200.203 netmask: 255.255.0.0 gateway: 192.168.200.201 The rest of our network is on 192.168.111.0/24 subnet. Ping only returns Destination Host Unreachable. I've tried various variations of this setup (including straight through cable), and I can't seem to get them to talk to each other. Any help appreciated.

    Read the article

  • Problem Assigning Static IP to CentOS Server

    - by nategood
    We have a sandbox server running CentOS that we run inside our office. Our ISP has assigned us a block of 5 static IPs. We now want to assign it a static IP. DEVICE=eth0 BOOTPROTO=none # have also tried "static" here HWADDR=00:13:72:*:*:* ONBOOT=yes TYPE=Ethernet NETMASK=255.255.255.0 IPADDR=173.*.*.161 GATEWAY=10.1.10.1 /etc/resolv.cnf is also set with the appropriate name servers from our ISP. When I ifdown eth0 then ifup eth0 I get... SIOCADDRT: Network is unreachable When I switch to DCHP, the machine has an IP assigned and there are no connection problems. Any ideas?

    Read the article

  • How do I stop apps trying to use a dial-up connection?

    - by ProfKaos
    Every now and again, I might have to use a dial-up internet connection via another tethered phone, i.e. Bluetooth connection to the GPRS modem. Now I am back on 'ops normal', i.e. using a shared internet connection on my own phone, or on my 3G stick, but some apps, especially IE9, keep popping up a 'dialup connection' dialogue, which I cannot dismiss enough times ever, to make to stay away. How can I tell these idiot applications that I no longer need a dial-up connection?

    Read the article

  • When I ping Internet addresses like yahoo or Google, I get 2 reply packets and 2 lost packets.

    - by navi
    I have Airtel broadband and a Tata broadband connection. i have around 50 PCs connecting through an airtel broadband connection. Both are dsl connections with my phone line going into dsl modems and an Ethernet cable going from dsl modem directly into a switch. Currently, only airtel connection is connected with static IP on my private lan and using the airtel ISP DNS servers as DNS IP address and the default gateway is 192.168.1.1 (IP add. of the dsl modem). All PCs are connected in a work group. When in full use, my users complain of certain web pages are not opening. When I ping Internet addresses like Yahoo or Google I get 2 reply packets and 2 lost packets. I suspect that a single broadband connection is not able to sustain 50 simultaneous downloads/browsing. Is there any device which connect to both DSL and make one line so that its give me high speed simultaneous browsing. Help needed urgently. Thank you all to those who reply.

    Read the article

  • Windows 7 DHCP Default Gateway not Overridden by manual Default Gateway

    - by dgwilson
    We have recently installed Windows 7 for student computers. All student computers must be routed through our content filter which is located at 192.168.0.63. This was done in WinXP by adding a Default Gateway in the network adapter settings TCP/IP Properties Advanced Default Gateway. All teacher computers are routed through the DHCP assigned Default Gateway of 192.168.0.1. In WinXP the dhcp default gateway was correctly overridden by this manual setting. In Win7 it appears that the dhcp default gateway is retained and the manual one is added to the list so that there are two with the dhcp one having the primary metric. I have tried several ways to remove the dhcp default gateway such as, running the "route delete 0.0.0.0 192.168.0.1" command. Doing this from an administrator command prompt works but it just resets upon reboot. I've tried adding this command to the registry's Run section but it seems to run as a non-administrator and therefore will not complete successfully. Is there any way to prevent this and force the manual default gateway to override the dhcp one? Or to remove the dhcp assigned one automatically on boot/login? HELP! We CANNOT allow student computers to connect to the internet without going through the content filter.

    Read the article

  • Windows 7 DHCP Default Gateway not Overridden by manual Default Gateway

    - by dgwilson
    We have recently installed Windows 7 for student computers. All student computers must be routed through our content filter which is located at 192.168.0.63. This was done in WinXP by adding a Default Gateway in the network adapter settings TCP/IP Properties Advanced Default Gateway. All teacher computers are routed through the DHCP assigned Default Gateway of 192.168.0.1. In WinXP the dhcp default gateway was correctly overridden by this manual setting. In Win7 it appears that the dhcp default gateway is retained and the manual one is added to the list so that there are two with the dhcp one having the primary metric. I have tried several ways to remove the dhcp default gateway such as, running the "route delete 0.0.0.0 192.168.0.1" command. Doing this from an administrator command prompt works but it just resets upon reboot. I've tried adding this command to the registry's Run section but it seems to run as a non-administrator and therefore will not complete successfully. Is there any way to prevent this and force the manual default gateway to override the dhcp one? Or to remove the dhcp assigned one automatically on boot/login? HELP! We CANNOT allow student computers to connect to the internet without going through the content filter.

    Read the article

  • Is there any reason to subnet a home network?

    - by Will
    For networks I understand we set a netmask on each computer to let it know what IPs it can talk to without going through the router - IPs on the same subnet can talk directly to each other and do not have to go through a router/switch. However, in today's home networks (and I suspect corporate networks as well) every computer is connected to a router/switch (at the low cost of today's hardware I doubt there it much of a market for wired repeaters/hubs). This seems to obviate the need for a subnet mask and subnetting. Considering that in most modern home architectures every computer goes through the router, even to talk to computers on the same network, is there any reason for me to subnet a home network?

    Read the article

  • Windows 7 - system error 5 problem

    - by Ian
    My wife has just had a new computer for Christmas (with an upgrade from VISTA to Windows 7), and has joined the home network. We are using a mix of WindowsXP and Ubuntu boxes linked via a switch. We are all in the same workgroup. (No domain). Internet access, DHCP, and DNS server is an SME server that thinks it is domain controller (although we are not using a domain). I need to run a script to back up my wife's machine (venus). In the past the script creates a share on a machine with lots of space (leda), and then executes the line. PSEXEC \\venus -u admin -p adminpassword -c -f d:\Progs\snapshot.exe C: \\leda\Venus\C-drive.SNA With the wife's old XP machine, this would run the sysinternals utility, copy shapshot,exe to her machine and run it, which would then back up her C: drive to the share on leda. I cannot get this to work with Windows 7, nor can I link through to the C$ share on her machine. This gives me a permissions error (system error 5). The admin account is a full admin account. And yes - I do know the password. The ordinary shares on her machine work fine! I guess I'm missing something that Microsoft have built into Windows 7 - but what? The machine is running Windows 7 business, with windows firewall, AVG anti virus, and all the crap-ware you get with a new PC removed. Thanks

    Read the article

  • Should I remove all unmanged switches from my network?

    - by IMAbev
    I have a office network with approx 150 devices (computers/printers/ip phones). Almost all of the end point devices have straight run Cat5e from my Hp switches directly to the device. IP phones for each end user sit between the hp switch and computer. (hp switch - in to phone out of phone in to computer) While I have gotten rid of most of them, I still have a couple linksys unmanaged switches that split off to 2 or more devices. I have heard various reasons for removing these switches but not entirely sure if it actually degrades the network. I agree that eliminating these switches certainly cleans up the network from a management standpoint. Are these unmanaged switches bad for my network? Is there a clear advantage to having 'home run' cable runs to each of my end point devices?

    Read the article

  • tool for monitoring network traffic on Windows 7 Home

    - by Xah Lee
    for Windows 7 Home Edition: can anyone recommend a tool to monitor network traffic? either build-in or 3rd-party. I like to have a graph view (e.g. as in Task Manager) but also nice are tool that lets me see what IP/port that's incoming/outgoing. Command line is fine. Or even some tutorial. Thanks. (am old unix sys admin and web app dev. Though not much of a network admin and don't know much Windows. I need this tool just for my home PC, not in any pro capacity.)

    Read the article

  • How to set the preffered network interface in linx

    - by Mike Cooper
    I have my network set up like this. http://docs.google.com/Doc?docid=0AZ1YxuLE4djaZGhqN2s1NmRfMjhjNjc0Ym1meg&hl=en In words: I have a machine (Calcium, running Arch Linux) that has two network interfaces. eth0 is hoooked up to a router, and is gigabit. Eth1 is hooked up directly to the university network over 10Megabit. The router's uplink is hooked up to the university network as well, and it is also 10Megabit. Currently (I believe) all traffic on Calcium is going through eth0, through the router, regardless of whether it is internal or external. (How can I confirm this?) Ideally, traffic that is destined for the internal network (192.168.10.0/24) would travel over eth0 to the router, and wherever it is going. ALL other traffic should go over eth1. I suspect that this behavior could be acheived with IP tables? I don't really know where to start looking to learn that though, so any links would be appreciated.

    Read the article

  • What is the correct iptables rule when NATing multiple private subnets?

    - by Jose Mendez
    I have a Centos minimal 6.5 acting as a router. eth0 is connected to a Cisco switch trunk port, allowing VLANs 200-213. I have several VLAN interfaces just as this link suggests: https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/6/html/Deployment_Guide/s2-networkscripts-interfaces_802.1q-vlan-tagging.html And have IPv4 forwarding, so all my network devices from any of the networks 200-213 can communicate with each other using this linux box as their router. Problem is, I need them to access the Internet, so I added the following rule: iptables -t nat -A POSTROUTING -s 192.168.0.0/16 -j SNAT --to 1.1.1.56 1.1.1.56 is the "outside" address. This works fine, devices connected to the internal networks can ping Intertnet addresses BUT, they stop being able to talk to each other across subnets, so 192.168.211.55 can ping 8.8.8.8, but can't talk to 192.168.213.5. As soon as I do a service iptables restart to remove the rule, I can start talking across internal subnets again. What would be the correct way to set up NAT for multiple private subnets? Or maybe the correct way to set up forwarding?

    Read the article

  • Assign fixed IP address via DHCP by DNS lookup

    - by Janoszen
    Preface I'm building a virtualization environment with Ubuntu 14.04 and LXC. I don't want to write my own template since the upgrade from 12.04 to 14.04 has shown that backwards compatibility is not guaranteed. Therefore I'm deploying my virtual machines via lxc-create, using the default Ubuntu template. The DNS for the servers is provided by Amazon Route 53, so no local DNS server is needed. I also use Puppet to configure my servers, so I want to keep the manual effort on the deployment minimal. Now, the default Ubuntu template assigns IP addresses via DHCP. Therefore, I need a local DHCP server to assign IP addresses to the nodes, so I can SSH into them and get Puppet running. Since Puppet requires a proper DNS setup, assigning temporary IP addresses is not an option, the client needs to get the right hostname and IP address from the start. Question What DHCP server do I use and how do I get it to assign the IP address based only on the host-name DHCP option by performing a DNS lookup on that very host name? What I've tried I tried to make it work using the ISC DHCP server, however, the manual clearly states: Please be aware that only the dhcp-client-identifier option and the hardware address can be used to match a host declaration, or the host-identifier option parameter for DHCPv6 servers. For example, it is not possible to match a host declaration to a host-name option. This is because the host-name option cannot be guaranteed to be unique for any given client, whereas both the hardware address and dhcp-client-identifier option are at least theoretically guaranteed to be unique to a given client. I also tried to create a class that matches the hostname like this: class "my-client-name" { match if option host-name = "my-client-name"; fixed-address my-client-name.my-domain.com; } Unfortunately the fixed-address option is not allowed in class statements. I can replace it with a 1-size pool, which works as expected: subnet 10.103.0.0 netmask 255.255.0.0 { option routers 10.103.1.1; class "my-client-name" { match if option host-name = "my-client-name"; } pool { allow members of "my-client-name"; range 10.103.1.2 10.103.1.2; } } However, this would require me to administer the IP addresses in two places (Amazon Route53 and the DHCP server), which I would prefer not to do. About security Since this is only used in the bootstrapping phase on an internal network and is then replaced by a static network configuration by Puppet, this shouldn't be an issue from a security standpoint. I am, however, aware that the virtual machine bootstraps with "ubuntu:ubuntu" credentials, which I intend to fix once this is running.

    Read the article

  • Cannot establish a network connect to VMWare Fusion VM

    - by twolfe18
    I am running Snow Leopard 10.6.2 (not the server edition) with VMWare Fusion 3.0.0 and I trying to get my Ubuntu 9.10 x86_64 VM working. I am using a bridged connection, and I have an internet connection FROM the Ubuntu VM (I can download updates, ping websites, etc), but I cannot connect TO the Ubuntu box from any other device on my network. I am trying to get Mongrel up on the Ubuntu VM for some Rails stuff, but it's not working. I know Mongrel/Rails is not the problem because if I start the server on the Ubuntu VM, background the process, and then wget the index page, it works. I just cannot connect to the site from another IP. I have tried using a static IP and a DHCP IP configuration on the Ubuntu VM, neither work (for incoming connections, both work for outwards). I have port scanned the Ubuntu VM, and it appears that all ports are closed. However, the Ubuntu VM does respond to pings. I noticed a similar question here: http://serverfault.com/questions/99757/setting-up-a-bridged-network-with-vmware-fusion, but no answer. Any ideas?

    Read the article

  • Most secure way of connecting an intranet to an external server

    - by Eitan
    I have an internal server that hosts an asp.net intranet application. I want to keep it completely and utterly secure and private however we need to expose some information through a WCF service to another server which hosts our external websites which CAN be accessed by the public. What is the best way to pass information between the two servers with regards to an IT setup, while keeping the intranet in house server completely secure and inaccessible? I've heard VPN was the way to go but I wanted to be sure this was the safest way. Another question what would be the most secure way of passing data in the WCF service?

    Read the article

  • Improving TCP performance over a gigabit network with lots of connections and high traffic of small packets

    - by MinimeDJ
    I’m trying to improve my TCP throughput over a “gigabit network with lots of connections and high traffic of small packets”. My server OS is Ubuntu 11.10 Server 64bit. There are about 50.000 (and growing) clients connected to my server through TCP Sockets (all on the same port). 95% of of my packets have size of 1-150 bytes (TCP header and payload). The rest 5% vary from 150 up to 4096+ bytes. With the config below my server can handle traffic up to 30 Mbps (full duplex). Can you please advice best practice to tune OS for my needs? My /etc/sysctl.cong looks like this: kernel.pid_max = 1000000 net.ipv4.ip_local_port_range = 2500 65000 fs.file-max = 1000000 # net.core.netdev_max_backlog=3000 net.ipv4.tcp_sack=0 # net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.core.somaxconn = 2048 # net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 65536 16777216 # net.ipv4.tcp_synack_retries = 2 net.ipv4.tcp_syncookies = 1 net.ipv4.tcp_mem = 50576 64768 98152 # net.core.wmem_default = 65536 net.core.rmem_default = 65536 net.ipv4.tcp_window_scaling=1 # net.ipv4.tcp_mem= 98304 131072 196608 # net.ipv4.tcp_timestamps = 0 net.ipv4.tcp_rfc1337 = 1 net.ipv4.ip_forward = 0 net.ipv4.tcp_congestion_control=cubic net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_tw_reuse = 0 # net.ipv4.tcp_orphan_retries = 1 net.ipv4.tcp_fin_timeout = 25 net.ipv4.tcp_max_orphans = 8192 Here are my limits: $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 193045 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1000000 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 1000000 [ADDED] My NICs are the following: $ dmesg | grep Broad [ 2.473081] Broadcom NetXtreme II 5771x 10Gigabit Ethernet Driver bnx2x 1.62.12-0 (2011/03/20) [ 2.477808] bnx2x 0000:02:00.0: eth0: Broadcom NetXtreme II BCM57711E XGb (A0) PCI-E x4 5GHz (Gen2) found at mem fb000000, IRQ 28, node addr d8:d3:85:bd:23:08 [ 2.482556] bnx2x 0000:02:00.1: eth1: Broadcom NetXtreme II BCM57711E XGb (A0) PCI-E x4 5GHz (Gen2) found at mem fa000000, IRQ 40, node addr d8:d3:85:bd:23:0c [ADDED 2] ethtool -k eth0 Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp-segmentation-offload: on udp-fragmentation-offload: off generic-segmentation-offload: on generic-receive-offload: on large-receive-offload: on rx-vlan-offload: on tx-vlan-offload: on ntuple-filters: off receive-hashing: off [ADDED 3] sudo ethtool -S eth0|grep -vw 0 NIC statistics: [1]: rx_bytes: 17521104292 [1]: rx_ucast_packets: 118326392 [1]: tx_bytes: 35351475694 [1]: tx_ucast_packets: 191723897 [2]: rx_bytes: 16569945203 [2]: rx_ucast_packets: 114055437 [2]: tx_bytes: 36748975961 [2]: tx_ucast_packets: 194800859 [3]: rx_bytes: 16222309010 [3]: rx_ucast_packets: 109397802 [3]: tx_bytes: 36034786682 [3]: tx_ucast_packets: 198238209 [4]: rx_bytes: 14884911384 [4]: rx_ucast_packets: 104081414 [4]: rx_discards: 5828 [4]: rx_csum_offload_errors: 1 [4]: tx_bytes: 35663361789 [4]: tx_ucast_packets: 194024824 [5]: rx_bytes: 16465075461 [5]: rx_ucast_packets: 110637200 [5]: tx_bytes: 43720432434 [5]: tx_ucast_packets: 202041894 [6]: rx_bytes: 16788706505 [6]: rx_ucast_packets: 113123182 [6]: tx_bytes: 38443961940 [6]: tx_ucast_packets: 202415075 [7]: rx_bytes: 16287423304 [7]: rx_ucast_packets: 110369475 [7]: rx_csum_offload_errors: 1 [7]: tx_bytes: 35104168638 [7]: tx_ucast_packets: 184905201 [8]: rx_bytes: 12689721791 [8]: rx_ucast_packets: 87616037 [8]: rx_discards: 2638 [8]: tx_bytes: 36133395431 [8]: tx_ucast_packets: 196547264 [9]: rx_bytes: 15007548011 [9]: rx_ucast_packets: 98183525 [9]: rx_csum_offload_errors: 1 [9]: tx_bytes: 34871314517 [9]: tx_ucast_packets: 188532637 [9]: tx_mcast_packets: 12 [10]: rx_bytes: 12112044826 [10]: rx_ucast_packets: 84335465 [10]: rx_discards: 2494 [10]: tx_bytes: 36562151913 [10]: tx_ucast_packets: 195658548 [11]: rx_bytes: 12873153712 [11]: rx_ucast_packets: 89305791 [11]: rx_discards: 2990 [11]: tx_bytes: 36348541675 [11]: tx_ucast_packets: 194155226 [12]: rx_bytes: 12768100958 [12]: rx_ucast_packets: 89350917 [12]: rx_discards: 2667 [12]: tx_bytes: 35730240389 [12]: tx_ucast_packets: 192254480 [13]: rx_bytes: 14533227468 [13]: rx_ucast_packets: 98139795 [13]: tx_bytes: 35954232494 [13]: tx_ucast_packets: 194573612 [13]: tx_bcast_packets: 2 [14]: rx_bytes: 13258647069 [14]: rx_ucast_packets: 92856762 [14]: rx_discards: 3509 [14]: rx_csum_offload_errors: 1 [14]: tx_bytes: 35663586641 [14]: tx_ucast_packets: 189661305 rx_bytes: 226125043936 rx_ucast_packets: 1536428109 rx_bcast_packets: 351 rx_discards: 20126 rx_filtered_packets: 8694 rx_csum_offload_errors: 11 tx_bytes: 548442367057 tx_ucast_packets: 2915571846 tx_mcast_packets: 12 tx_bcast_packets: 2 tx_64_byte_packets: 35417154 tx_65_to_127_byte_packets: 2006984660 tx_128_to_255_byte_packets: 373733514 tx_256_to_511_byte_packets: 378121090 tx_512_to_1023_byte_packets: 77643490 tx_1024_to_1522_byte_packets: 43669214 tx_pause_frames: 228 Some info about SACK: When to turn TCP SACK off?

    Read the article

  • Forward all tracif from one IP to another Ip on OS X

    - by Josh
    This is related to this question I just asked... I have two IP address on my iMac I want to "bridge". I'm not sure what the proper terminology is... here's the situation. My iMac has a firewire connection to my laptop and an ethernet connection to the rest of my office. My laptop has an ip of 192.168.100.2 (on the firewire interface). My iMac has an IP of 192.168.100.1 on the firewire interface, and two IPs, 10.1.0.6 and 10.1.0.7, on it's ethernet interface. If I wanted to forward all traffic coming in from 192.168.100.2 on my OS X machine to go out on IP 10.1.0.7, and vice-versa, can this be done? I assume I would use the ipfw command. Essentially I want to "bridge" the firewire network to the ethernet network so my laptop can see all the machines on the 10.1 network, and all those machines can see my laptop at 10.1.0.7. Is this possible?

    Read the article

  • Rename a Network Printer win Win 7

    - by Alex
    Seems this is a common question but the answers regularly miss the point. I have a server. Server has some printers connected. Server has all drivers for x32 & x64 OS PLUS ALL DEFAULTS set. Server also manages print queue. I have many workstations, all need to use the printers. All NEED to have drivers print queue and DEFAULTS propagated from server. Now.... When I add the printers on the workstations, I get: "ABC Printer on SERVER123" I need something less long - just "ABC Printer" So how? Tip: Please don't show me how to change the name of your locally installed printer. I know how to do this - I am particularly interested in shared printers that look like "ABC Printer on SERVER123" Tip: Installing the driver with a local port wont cut it because then I loose the server propagated defaults, the driver updates and I need to run around with driver disks/confuse trembling users with hard things like choosing drivers. I am happy for a hack if there is no official way to do this in the group policy.... I tried looking in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Printers on the workstation machines but those are only local printers :( I can see the network printer details on the workstations here: HKEY_USERS[Some GUID]\Printers\Connections But there is nothing obvious like a description string... Can anyone help with this?

    Read the article

  • Turn old rack server into a telephone server

    - by Jake Elsley
    I have an old server lying around and I am thinking of using it as an internal telephone server. Its main use would be to set up a 1 to 1 telephone system that could be used internally to connect to different users in different offices. I have looked at software like Asterisk, but it seems that this is mainly for external telephone systems. Is this possible to do with Asterisk (or other software) or is this not possible without involving a VOIP company?

    Read the article

< Previous Page | 152 153 154 155 156 157 158 159 160 161 162 163  | Next Page >