Search Results

Search found 26285 results on 1052 pages for 'grant back'.

Page 158/1052 | < Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >

• Rack Mounting a Server with hot air vents on the top?

  - by Adam

  We just got a couple of HP DL360 G7's, and I notice it has vents on the top. More hot air seems to exit through these vents than it does anywhere on the back. All our servers in the past have always vented all the hot air through the back. How are these servers with top vents supposed to be mounted? Everyone always says airflow is best by not leaving gaps on the rack, but it seems like a server right on top of it would receive a lot of heat.

  Read the article

• How do I securely share / allow access to a drive?

  - by sleske

  To simplify backing up a laptop (Windows Vista), I'm planning on sharing its C: drive (with password protection) and using that to back it up from another computer. What are the security implications of this? If I share C: with a reasonable password, how big is the risk of compromise if the system is e.g. inadvertently used on a public WLAN or similar? Background: I'm planning to use [Areca Backup][1] to back up two systems (Windows XP and Vista). My current plan is to install Areca on the XP box, and share the Vista system's C: as a shared folder, so the XP system can read it. Then I can set up the drive as a network drive and have Areca read it like a local drive. Of course, if you can think of a more elegant way of doing this, I'm open to suggestions.

  Read the article

• Ubuntu server: lost prompt on monitor

  - by Richard

  Hello All, I am running Ubuntu 9.04 server edition. I have a monitor plugged into the box for occasional admin tasks. I pulled out a USB disk (without unmounting) and the screen is now full with this message: Buffer I/O error on device sdc1, logical block 7778778 I can't seem to clear the screen or get a prompt back. Doesn't appear to be registering keyboard strokes. The box is still running fine (I can ssh in from elsewhere and evrything is running as normal). Any ideas on how to clear screen and get my prompt back?

  Read the article

• Server suddenly running out of entropy

  - by Creshal

  Since a reboot yesterday, one of our virtual servers (Debian Lenny, virtualized with Xen) is constantly running out of entropy, leading to timeouts etc. when trying to connect over SSH / TLS-enabled protocols. Is there any way to check which process(es) is(/are) eating up all the entropy? Edit: What I tried: Adding additional entropy sources: time_entropyd, rng-tools feeding urandom back into random, pseudorandom file accesses – netted about 1 MiB additional entropy per second, problems still persisted Checking for unusual activity via lsof, netstat and tcpdump – nothing. No noticeable load or anything Stopping daemons, restarting permanent sessions, rebooting the entire VM – no change in behaviour What in the end worked: Waiting. Since about yesterday noon, there are no connection problems anymore. Entropy is still somewhat low (128 Bytes peak), but TLS/SSH sessions have no noticeable delay anymore. I'm slowly switching our clients back to TLS (all five of them!), but I don't expect any change in behavior now.

  Read the article

• Why did the web win the space of remote applications and X not?

  - by Martin Josefsson

  The X Window System is 25 years old, it had it's birthday yesterday (on the 15'th). As you probably are aware of, one of it's most important features is the separation of the server side and the client side in a way that neither Microsoft's, Apples or Wayland's windowing systems have. Back in the days (sorry for the ambiguous phrasing) many believed X would dominate over other ways to make windows because of this separation of server and client, allowing the application to be ran on a server somewhere else while the user clicks and types on her own computer at home. This use obviously still exists, but is marginalized at best. When we write and use programs that run on a server we almost always use the web with it's html/css/js. Why did the web win, and X not? The technologies used for the web (said html/css/js) are a mess. Combined with all the back-end-frameworks (Rails, Django and all) it really is a jungle to navigate thru. Still the web thrives with creativity and progress, while remote X apps do not.

  Read the article

• How does the TuneIn mobile application resume a live stream, when the connection breaks?

  - by navnav

  So I have this TuneIn application on my phone, which allows me to listen to many radio stations. It also allows me to rewind and pause the live stream, which I know is doable with today's technology. What gets me puzzled, though, is how when the internet connection breaks, the live stream will stop, but, when the connection comes back, the app can just pick up from where it broke. Why it gets me puzzled is because there is no way for the app to cache the live stream when the net connection has gone, yet it can start the live stream back up, from where it broke. Is there is possible to start a live stream, at a specific point of the audio stream? Or are they using some other method?

  Read the article

• Best practice, or generally best way to set up web-hosting server, permissions, etc.

  - by Jagot

  Hi, I'm about to set up a server upon which a friend and I will be hosting web sites, and I'll be using Debian. I've set up a LAMP solution many times just to using for local testing purposes, but never for actual production use. I was wondering what are the best practices are in terms of setting the server up, in reference specifically to accessing the web root directory. A couple of the options I have seen: Set up a single user account on the server for us both to use and use a virtual host to point to the somewhere in the home directory, e.g. /home/webdev/www. Set each of us up a user account, and grant permissions in some way to /var/www (What would be the best way? Set up a new group?) I want to get this right when I first set this up as there won't be any going back for a while once our first site is up and running. Appreciate any guidance in advance.

  Read the article

• Files slow to save sometimes after Ubuntu upgrade

  - by Matchu

  I haven't quite been able to track down why this happens sometimes in Ubuntu 10.04 and not other times. I'll go into gedit or OpenOffice.org and try to save files, and, during some sessions, it will take up to 10 seconds to save the file, sometimes causing the program to become unresponsive. But during these same sessions, the files sometimes save instantly. This didn't start happening until after the 10.04 (Lucid) upgrade. I suspect that something is reading all the changes I make, or that there's some other big file action going on, or something like that. I disabled Tracker a while back, before the upgrade, and don't see it under the settings - could it be back under a different name under Lucid? You probably don't already know the answer, but how can I go about finding the cause of this problem?

  Read the article

• Unable to set NTFS permissions for ApplicationPoolIdentity on Windows 2008 SP2

  - by Kev

  On Windows 2008 R2 I am able to set NTFS permissions for an application pool's synthesised ApplicationPoolIdentity account thus: ICACLS d:\websites\site1\www /grant "IIS AppPool\site1":(CI)(OI)(M) The website's application pool is named site1 and is configured to run as ApplicationPoolIdentity. The site's authentication is also configured to authenticate as ApplicationPoolIdentity. I've done this a thousand times on Windows 2008 Standard Edition R2 with never a hitch. However if I try to do the same in Windows 2008 Standard Edition SP2 I get the error: IIS AppPool\site1: No mapping between account names and security IDs was done. Successfully processed 0 files; Failed processing 1 files I also notice that this fails if I try to set permissions for the application pool identity via the security GUI as well. I've seen this before and a reboot has cleared this issue but I'd like to know why this happens periodically. Googling around suggests other folks have hit this problem but there's never a satisfactory explanation. Why would this be?

  Read the article

• How can I render a semi transparent model with OpenGL correctly?

  - by phobitor

  I'm using OpenGL ES 2 and I want to render a simple model with some level of transparency. I'm just starting out with shaders, and I wrote a simple diffuse shader for the model without any issues but I don't know how to add transparency to it. I tried to set my fragment shader's output (gl_FragColor) to a non opaque alpha value but the results weren't too great. It sort of works, but it looks like certain model triangles are only rendered based on the camera position... It's really hard to describe what's wrong so please watch this short video I recorded: http://www.youtube.com/watch?v=s0JqA0rZabE I thought this was a depth testing issue so I tried playing around with enabling/disabling depth testing and back face culling. Enabling back face culling changes the output slightly but the problem in the video is still there. Enabling/disabling depth testing doesn't seem to do anything. Could anyone explain what I'm seeing and how I can add some simple transparency to my model with the shader? I'm not looking for advanced order independent transparency implementations. edit: Vertex Shader: // color varying for fragment shader varying mediump vec3 LightIntensity; varying highp vec3 VertexInModelSpace; void main() { // vec4 LightPosition = vec4(0.0, 0.0, 0.0, 1.0); vec3 LightColor = vec3(1.0, 1.0, 1.0); vec3 DiffuseColor = vec3(1.0, 0.25, 0.0); // find the vector from the given vertex to the light source vec4 vertexInWorldSpace = gl_ModelViewMatrix * vec4(gl_Vertex); vec3 normalInWorldSpace = normalize(gl_NormalMatrix * gl_Normal); vec3 lightDirn = normalize(vec3(LightPosition-vertexInWorldSpace)); // save vertexInWorldSpace VertexInModelSpace = vec3(gl_Vertex); // calculate light intensity LightIntensity = LightColor * DiffuseColor * max(dot(lightDirn,normalInWorldSpace),0.0); // calculate projected vertex position gl_Position = gl_ModelViewProjectionMatrix * gl_Vertex; } Fragment Shader: // varying to define color varying vec3 LightIntensity; varying vec3 VertexInModelSpace; void main() { gl_FragColor = vec4(LightIntensity,0.5); }

  Read the article

• Special function keys are mixed up on my Macbook Pro

  - by seanieb

  I recently sent my Macbook Pro (late 2008 model) to get a replaced logic board and top cover. When I got it back the Special function keys are mixed up. F3 - mutes sound - it should do expose f4 - decreases volume - it should show the dashboard f5 - increases volume ....etc, ... F11 - expose - it should decrease volume f12 - dashboard - it should increase volume I have checked and made sure that System PreferencesKeyboard"use all F keys as standard function keys" is not selected. And that no accessibility options are switched on either. How do I fix this? or should I bring it back to the repair shop? Thanks

  Read the article

• X won't start, root filesystem mounted read only

  - by TK Kocheran

  I just experienced a very strange and puzzling problem on my machine that I can't seem to get sorted out. I was running Windows on a second partition, and everything was working great. I then went to restart into Linux, and noticed that X wouldn't start. Everything was displayed in super-low resolution, so I tried reinstalling my NVIDIA driver. I started seeing all of these I/O error problems, so I figured that my SSD was bad. After a bit more playing around, I ran fsck on the drive when mounted from a startup disk as well as badsectors and everything looked great. The SMART drive tests all passed and again, everything was looking good, so I rebooted again and still, no joy. I started then getting some weird USB errors, so I followed someone's advice and unplugged my computer's power supply, then started back up again and my graphics looked a lot better in the BIOS and in the boot logo, but X still wouldn't start. I then found out that my main boot drive was being mounted read-only for some reason. What's going wrong? I've done some pretty extensive tests on the SSD from a startup disk such as writing massive files, reading big files, running filesystem checks on the entire disk, and everything is looking great, until I try to boot. Whenever I try installing the drivers with apt-get, I get a ton of ata error messages looking like this: How can I diagnose what's going wrong and fix it so I can get back to work?

  Read the article

• How can I switch Linux running OS from disk to running from RAM without restarting?

  - by vfclists

  Is it possible to switch to running Linux from RAM or RAM disk after starting starting initially from disk? eg. You need to make an image of your hard disk, FTP it to a remote location, some time later you want the image back, so you start the system from disk as usual, restore the image you FTP'd from the remote location back into place. More like a CloneZilla backup and restore, without booting the server from CD or USB disk, but starting from the normal hard disk? Notes on environment I should have mentioned it earlier. It is a remotely hosted VM where I cannot boot into a recovery console mode or do a netinstall. It will always boot onto the same disk. Which means that if there is some serious corruption I can't repair it offline, which is why being able to ftp a previously saved backup into place is so important

  Read the article

• Tumblr custom domain not redirecting properly

  - by Manic

  I decided to host my blog at Tumblr, using their custom domain setup (http://blog.smokingfishgames.com/ instead of http://smokingfishgames.tumblr.com). However, it's been 72 hours and I'm still getting spotty redirection. It works some of the time--I go and see the page and blog, and it's all fine. However, it occasionally just stops working and redirects back to my web host, which is a directory with nothing but a single file called BUGGER.html (which I stuck in to make sure that it was my web host and not some Tumblr empty directory). Clearing the Chrome DNS cache makes the problem go away--for a while. After a few minutes, or an hour, or however long, I'll start seeing BUGGER.html again. I clear the cache, and poof, the blog shows up. The thing that's curious to me is that when I clear the cache and get BUGGER.html again (which happens occasionally), I can look at my Chrome DNS cache and see assets.tumblr.com UNSPECIFIED blog.smokingfishgames.com UNSPECIFIED www.tumblr.com UNSPECIFIED IP addresses and expiration times omitted for brevity's sake--if they're important I'm sure I can replicate the issue. This implies, to me anyway, that my browser is reaching Tumblr but getting bounced back to my web host. Any reason why this would be happening, or is this a normal symptom of DNS propagation? If it is a problem, should I be bothering Tumblr or my host with it, or is this something I can fix myself?

  Read the article

• convert outline to text

  - by Pai Gaudêncio

  howdy, how can i convert an outlined text back to editable text in adobe illustrator? thanks.

  Read the article

• Distributed Nagios Installation

  - by kruczkowski

  I'm looking for a plug-in or product that will act as a remote probe and perform tests then send back the results to the central Nagios server. Reason for this is that I'd like to monitor internal systems and servers at customers, but don't want to allow all the traffic passing the firewalls. Ideally I'd like a soft-probe that would be installed and then perform the tests and send back the results (via SSH) to the central Nagios installation. Does anyone know of a product or plug-in that would offer such service? If not Nagios, is there any other monitoring system that does such a thing (ideally open-source)?

  Read the article

• linux: selective sudo access for a particular command

  - by bguiz

  Hi, Is it possible to grant a particular user sudo access for one particular command only? Thanks -- More info: We farm out lengthy optimisation runs to each other's boxes over ssh. These runs take hours, sometimes days. The shutdown command can only be run in sudo. Being conscious of my environmental footprint, I would like to give the initiator(s) of these runs sudo access to the shutdown command on my box, without sudo access for everything else - so that they may shutdown my machine when they no longer need it. I am aware that I can schedule a shutdown before I leave my box, but I am looking for a better solution.

  Read the article

• Is sending data to a server via a script tag an outdated paradigm?

  - by KingOfHypocrites

  I inherited some old javascript code for a website tracker that submits data to the server using a script url: var src = "http://domain.zzz/log/method?value1=x&value2=x" var e = document.createElement('script'); e.src = src; I guess the idea was that cross domain requests didn't haven't to be enabled perhaps. Also it was written back in 2005. I'm not sure how well XmlHttpRequests were supported at the time. Anyone could stick this on their website and send data to our server for logging and it ideally would work in most any browser with javascript. The main limitation is all the server can do is send back javascript code and each request has to wait for a response from the server (in the form of a generic acknowledgement javascript method call) to know it was received, then it sends the next. I can't find anyone doing this online or any metrics as to whether this faster or more secure than XmlHttpRequests. I don't know if this is just an old way of doing things or it's still the best way to send data to the server when you are mostly trying to send data one way and you need the best performance possible. So in summary is sending data via a script tag an outdated paradigm? Should I abandon in favor of using XmlHttpRequsts?

  Read the article

• How to integrate a PHP CMS with paypal so that only users who completed a payment can register and authenticate?

  - by ibiza

  I am currently using a PHP CMS - cmsmadesimple - in order to create a website where services will be sold. I intend to use Paypal 'Buy Now' buttons in order to offer a few packages that will be renewable every 1-month or every 3-months and that grant access to the secure content of the website for a given period of time. Everything is going well so far but I am somewhat at loss for the user registration process as I have a few constraints I would like to use and it would be nice to automate the process if possible. Here are the constraints : User should be able to register to my website and choose a password himself Only users that paid should be able to register Access permissions should be disabled automatically after the service period if the package is not renewed And here is the process which I am thinking of : User clicks 'buy' on my website User is redirected on Paypal and completes the payment The paypal email used to pay should be returned to my server and somehow stored If it is a new email, user needs to register to my website (else if it is a returning customer, the deactivation flag for payment stopped should be removed to give back access) If a user does not renew his subscription, there should be a deactivation flag automatically set to the email used in order to lock access until next payment. Ideally, no human intervention is needed. What is the best way to implement all this? I am a bit at loss. I found this article that explained a few things and even has a nice code snippet, except that I'm not sure where to plug it. Thanks all

  Read the article

• Computer Locks Up Completely When Resuming From Standby

  - by kcoppock

  Okay, so I'm having a strange issue lately with my desktop, and off the top of my head I'm not sure what the problem is, so I'm hoping for some ideas on how to track down the cause. First, my PC: AMD Phenom 9600 Quad-Core 2.4 GHz 4 GB DDR2 160 GB boot HDD 1 TB & 120 GB secondary HDD Nvidia GeForce 8600 GTS Windows 7 Professional 64-bit I have my power settings as follows: Turn off the display: 10 minutes Turn off hard disk: 20 minutes Sleep after: Never After a while, I'll come back to use my computer again, wiggle the mouse, and the screen comes back on like normal, but the desktop is unresponsive. I can move the cursor, but nothing responds to clicks or keyboard entry. If I click a few times with the mouse, the computer eventually locks up completely and the mouse cursor stops moving as well. After I restart, everything works just fine. Is there a log you recommend checking or really any suggestions would be welcome at this point. Thanks!

  Read the article

• My iPhone is stuck at screen with USB cable and iTunes logo

  - by alex

  I just tried updating the iPhone's firmware, and things went haywire. iTunes informed the update had failed and linked me to this page. The iPhone is stuck on the image from the top of that page. I held down the sleep and home buttons until it turned off and turned it back on, and then went through the iPhone's 'restore' mode. It then error'd again and I'm stuck back with the logos on the iPhone. Does anyone know how to fix this? Thanks

  Read the article

• Stop WSUS from rebooting a server

  - by sixlettervariables

  Our IT department is rolling out a set of patches via WSUS this weekend and will reboot all of our Win2k3 servers on Sunday. Due to production work which must continue uninhibited, we cannot allow this reboot to occur. The exact line we have been given is: The command to download the patches and reboot on Sunday has been sent by WSUS already and cannot be taken back. The servers will reboot on Sunday automatically. How can we go about stopping this from happening? It set some flag saying it should reboot, so what flag do we unset? One strategy proposed was to roll back the system clock, however, this will likely cause some processes to fail.

  Read the article

• Git repo: Unravelling my mess into tidy branches

  - by Martin

  I wanted to play with a project, so git cloned it and, following its instructions, created a local branch for my configuration (I guess so that users can merge updates back). At first I was just tweaking to suit my preferences, so I didn't bother with any further branching, but now I have some code that might be useful to someone else, but with my passwords, etc in the same branch. Effectively, I have one big branch from which I'd like to have: Postgres backend (default) but with some new code I've added MySQL backend (the biggest change I've made) with that same new code My settings: I can't git ignore the settings file because I occasionally have to add sections for new functionality, but I need to keep my personal settings out of the public branches! I guess this would work best as a local-only branch. Dev branches, which I would branch from the MySQL. Starting from scratch, I think I could figure out how to branch/merge the various updates, but is there an easy way to walk through the existing repo and choose which commits to apply to which branch? Or possibly create a branch from a point upstream then merge back, excluding certain commits?

  Read the article

• The Start of a Blog

  - by dbradley

  So, here's my new blog up and running, who am I and what am I planning to write here?First off - here's a little about me:I'm a recent graduate from university (coming up to a year ago since I finished) studying Software Engineering on a four year course where the third year was an industrial placement. During the industrial placement I went to work for a company called Adfero in a "Technical Consultant" role as well as a junior "Information Systems Developer". Once I completed my placement I went back to complete my final year but also continued in my developer role 2/3 days a week with the company.Working part time while at uni always seems like a great idea until you get half way through the year. For me the problem was not so much having a lack of time, but rather a lack of interest in the course content having got a chance at working on real projects in a live environment. Most people who have been graduated a little while also find this - when looking back at uni work, it seem to be much more trivial from a problem solving point of view which I found to be true and I found key to uni work to actually be your ability to prove though how you talk about something that you comprehensively understand the basics.After completing uni I then returned full time to Adfero purely in the developer role which is where I've now been for almost a year and have now also taken on the title of "Information Systems Architect" where I'm working on some of the more high level design problems within the products.What I'm wanting to share on this blog is some of the interesting things I've learnt myself over the last year, the things they don't teach you in uni and pretty much anything else I find interesting! My personal favorite areas are text indexing, search and particularly good software engineering design - good design combined with good code makes the first step towards a well-written, maintainable piece of software.Hopefully I'll also be able to share a few of the products I've worked on, the mistake I've made and the software problems I've inherited from previous developers and had to heavily re-factor.

  Read the article

• Set a row to follow my cursor anywhere in Calc

  - by NoCanDo

  How do I make a whole row follow wherever I am in the Calc document when I scroll down/up? I'm looking for something that keeps a row from moving, or to make it stay put. This is so that when I want to see other rows, this one locked row will stay in place and allow me to refer back to it on screen without having to scroll all the way back up to the top of the document. Normal: Scrolled down: Further scrolled down: You can see the row with the yellow background, (CD-Nr.|Title|Genre|Lang|CD) is following me as I scroll down. How is this done?

  Read the article

< Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >