Search Results

Search found 22204 results on 889 pages for 'input devices'.

Page 158/889 | < Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >

• How to find ip address of my Asus RT-AC86U in Access Point mode?

  - by WilliamKF

  I'm using an Asus wireless router model RT-AC68U and can connect fine to the internet using it wirelessly. I configured the router to be an Access Point, but having done so, I can no longer locate the GUI to adjust the router as I have no idea what its IP Address is anymore. The router is plugged into a cable modem and router which is a model SMCD3G is a business class gateway labeled Comcast Business IP Gateway. This gateway is assigning ip addresses in the range 10.1.10.XX and I went to the web interface at 10.1.10.1 and listed the connected devices and see my laptop which is connected to the Asus access point along with a few other devices, but none of the devices listed are the Asus router (I tried all the six ip addresses listed). How can I determine the IP Address of my Asus router in access point mode so I can see the GUI interface again to control the router other than by doing a factory reset?

  Read the article

• Generic C# Class: Set "Generic" Property

  - by BlaM

  I'm quite new to C#, so I might have a problem that C# has a simple solution for. I have a generic class with a property of "generic" type. I want to have a function to set that property, but I need to convert it to do so. public class BIWebServiceResult<T> { public T Data; public delegate StatusCode StringToStatusCode(string Input); public void SetData(string Input, StringToStatusCode StringToError) { if (StringToError(Input) == 0) { if (Data is string[]) { Data = new string[1]; Data[0] = Input; } else if (Data is string) { Data = Input; } else if (Data is bool) { Data = DetectBool(Input); } } } private bool DetectBool(string Compare) { return Compare == "true"; } } The problem with that approach is, that it does not work :) (No that's not all code, just a snippet to show what my problem is) It doesn't even compile, because "Data = new string[]" can't work if Data is - for example - boolean. How do I implement a function that behaves differently depending on the type of my generic property?

  Read the article

• Using Javascript to submit forms.

  - by Razor Storm

  I am using a jQuery function to submit a form when a certain button is pressed, however this seems to have no effect on the form. My code is as follows: HTML: <form id="loginForm" action="" method="POST"> <input class="loginInput" type="hidden" name="action" value="login"> <input id="step1a" class="loginInput" type="text" name="username"> <input id="step2a" class="loginInput" type="password" name="password" style="display:none;"> <input id="step1b" class="loginSubmit" onclick="loginProceed();" type="button" name="submit" value="Proceed" title="Proceed" /> <input id="step2b" class="loginSubmit" onclick="submitlogin();" type="button" value="Validate" title="Validate" style="display:none;" /> Javascript: function submitlogin() { $("form").submit(); } However, when I press the button, absolutely nothing occurs. PS. This function may seem meaningless since I can just use a input type="submit" but I originally intended this to have some more functionality, I stripped the function to its bare bones for testing purposes.

  Read the article

• ASIHTTPRequest wrapper usage for Macs

  - by Rob

  I am trying to apply the ASIHTTPRequest wrapper to a very basic Objective C program. I have already copied over the necessary files into my program and after giving myself an extreme headache trying to figure out how it works through their website I thought I would post a question on here. The files copied over were: ASIHTTPRequestConfig.h ASIHTTPRequestDelegate.h ASIProgressDelegate.h ASIInputStream.h ASIInputStream.m ASIHTTPRequest.h ASIHTTPRequest.m ASIFormDataRequest.h ASIFormDataRequest.m My program is very basic: #import <Foundation/Foundation.h> int main (int argc, const char * argv[]) { NSAutoreleasePool * pool = [[NSAutoreleasePool alloc] init]; // Defining the various variables. char firstName[20]; char lastName[20]; char rank[5]; int leaveAccrued; int leaveRequested; // User Input. NSLog (@"Please input First Name:"); scanf("%s", &firstName); NSLog (@"Please input Last Name:"); scanf("%s", &lastName); NSLog (@"Please input Rank:"); scanf("%s", &rank); NSLog (@"Please input the number leave days you have accrued:"); scanf("%i", &leaveAccrued); NSLog (@"Please input the number of leave days you are requesting:"); scanf("%i", &leaveRequested); // Print results. NSLog (@"Name: %s %s", firstName, lastName); NSLog (@"Rank: %s", rank); NSLog (@"Leave Accrued: %i", leaveAccrued); NSLog (@"Leave Requested: %i", leaveRequested); [pool drain]; return 0; } How do I utilize the wrapper to export these 5 basic variables to a web server via an http request?

  Read the article

• Recursive list of lists in XSL

  - by Paul Tomblin

  I have a recursive nodes that I'm trying to set up for jquery-checktree. The nodes look like foo/bar/ID /NAME /CHECKED bar/ID /NAME /CHECKED /bar/ID /NAME /bar/ID /NAME /bar/ID /NAME /CHECKED /bar/ID /NAME /CHECKED Where any bar may or may not have one or more bar nodes below it, but any bar will have ID and NAME and might have a CHECKED. and I want to turn that into <ul> <li><input type="checkbox" name="..." value="..." checked="checked"></input> <label for="...">...</label> <ul> <li><input type="checkbox" name="..." value="..." checked="checked"></input> <label for="...">...</label> </li> </ul> <li>....</li> </ul> I can get the first level by doing: <ul class="tree"> <xsl:for-each select="/foo/bar/"> <li><input type="checkbox" name="{ID}" value="{ID}"> <xsl:if test="CHECKED = 'Y'"><xsl:attribute name="checked">checked</xsl:attribute></xsl:if> </input><label for="{ID}"><xsl:value-of select="NAME"/></label> </li> </xsl:for-each> </ul> But I don't know how to recurse down to the embedded "bar" within the "bar", down to however many levels there might be.

  Read the article

• Pass checkbox values with Jquery to PHP and display result in div

  - by user1343955

  I want to filter realtime results with jQuery (just like on this site http://shop.www.hi.nl/hi/mcsmambo.p?M5NextUrl=RSRCH). So when someones checks a checkbox the results should update realtime (in a div). Now I'm a newbie with jQuery and I've tried lots of examples but I can't get it to work. Here's my code, could anyone tell what I'm doing wrong? Thank you very much! HTML <div id="c_b"> Kleur:<br /> <input type="checkbox" name="kleur[1]" value="Blauw"> Blauw <br /> <input type="checkbox" name="kleur[2]" value="Wit"> Wit <br /> <input type="checkbox" name="kleur[3]" value="Zwart"> Zwart <br /> <br /> Operating System:<br /> <input type="checkbox" name="os[1]" value="Android"> Android <br /> <input type="checkbox" name="os[2]" value="Apple iOS"> Apple iOS <br /> </div> <div id="myResponse">Here should be the result</div> jQuery function updateTextArea() { var allVals = []; $('#c_b :checked').each(function() { allVals.push($(this).val()); }); var dataString = $(allVals).serialize(); $.ajax({ type:'POST', url:'/wp-content/themes/u-design/filteropties.php', data: dataString, success: function(data){ $('#myResponse').html(data); } }); } $(document).ready(function() { $('#c_b input').click(updateTextArea); updateTextArea(); }); PHP //Just to see if the var passing works echo var_export($_POST);

  Read the article

• Using JQuery with dynamically added controls (MVC)

  - by Mario

  I have a set of radio buttons that are dynamically generated (via JSON call): StringBuilder sbEligAll = new StringBuilder(); sbEligAll.Append("<div id='currentselectiondepartment'>"); sbEligAll.Append(" <input type='radio' name='selectalldepartment' id='radCurrent' value='0' /><label for='radCurrent'>Current</label>"); sbEligAll.Append(" <input type='radio' name='selectalldepartment' id='radFuture' value='1' /><label for='radFuture'>Future</label>"); sbEligAll.Append(" <input type='radio' name='selectalldepartment' id='radCurrentAll' value='2' /><label for='radCurrentAll'>Current All</label>"); sbEligAll.Append(" <input type='radio' name='selectalldepartment' id='radFutureAll' value='3' /><label for='radFutureAll'>Future All</label>"); sbEligAll.Append("</div>"); Then: return Json(new { TableList = sbElig.ToString() }, JsonRequestBehavior.AllowGet); Is there a way to get jQuery to be able to interact with these? For example: $("input[name=selectalldepartment]").change(function() { var str = $('input[name=selectalldepartment]:checked').val(); $(".radiolist[value='" + str + "']").attr("checked", true); }); I've tried everything I know how to do, but the jQuery just doesnt fire. (I've added alerts to the jQuery code to see if it actually gets called, and it does not). Any thoughts?! Thanks!

  Read the article

• How do I access an Ubuntu VirtualBox guest at a static IP from an OS X host?

  - by David Siegel

  How does one configure an Ubuntu guest to use a static IP that's visible to an OS X host, and ensure that the static IP is independent of the host's network configuration? I previously used bridged networking for my guest, but I'm constantly moving my host between networks so the guest IP is always different. First, I tried setting the guest network configuration to NAT and forwarding host port 1022 to guest port 22, so I could at least ssh to a fixed address (localhost:1022): $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/Protocol" "TCP" $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/GuestPort" 22 $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/HostPort" 1022 Then, $ ssh localhost -p 1022 ssh: connect to host localhost port 1022: Connection refused But this didn't work (guest has no network access with NAT and OS X refused the connection, as you can see). I'd love a general solution that would let me communicate with my guest at a fixed IP.

  Read the article

• Can PHP dissect its own syntax?

  - by Nathan Long

  Can PHP dissect its own syntax? For example, I'd like to write a function that takes in an input like $object->attribute and says to itself: OK, he's giving me $foo->bar, which means he must think that $foo is an object that has a property called bar. Before I try accessing bar and potentially get a 'Trying to get property of non-object' error, let me check whether $foo is even an object. The end goal is to echo a value if it is set, and fail silently if not. I want to avoid repetition like this: <input value="<? if(is_object($foo) && is_set($foo->bar)){ echo $foo->bar; }?> "/> ...and to avoid writing a function that does the above, but has to have the object and attribute passed in separately, like this: <input value="<? echoAttribute($foo,'bar') ?>" /> ...but to instead write something which: preserves the object-attribute syntax is flexible: can also handle array keys or regular variables Like this: <input value="<? echoIfSet($foo->bar); ?> /> <input value="<? echoIfSet($baz['buzz']); ?> /> <input value="<? echoIfSet($moo); ?> /> But this all depends on PHP being able to tell me "what kind of thing am I asking for when I say $object->attribute or $array[$key]", so that my function can handle each according to its own type. Is this possible?

  Read the article

• PHP, MySQL: mysql substitute for php in_array function

  - by Devner

  Hi all, Say if I have an array and I want to check if an element is a part of that array, I can go ahead and use in_array( needle, haystack ) to determine the results. I am trying to see the PHP equivalent of this for my purpose. Now you might have an instant answer for me and you might be tempted to say "Use IN". Yes, I can use IN, but that's not fetching the desired results. Let me explain with an example: I have a column called "pets" in DB table. For a record, it has a value: Cat, dog, Camel (Yes, the column data is a comma separated value). Consider that this row has an id of 1. Now I have a form where I can enter the value in the form input and use that value check against the value in the DB. So say I enter the following comma separated value in the form input: CAT, camel (yes, CAT is uppercase & intentional as some users tend to enter it that way). Now when I enter the above info in the form input and submit, I can collect the POST'ed info and use the following query: $search = $_POST['pets']; $sql = "SELECT id FROM table WHERE pets IN ('$search') "; The above query is not fetching me the row that already exists in the DB (remember the record which has Cat, dog, Camel as the value for the pets column?). I am trying to get the records to act as a superset and the values from the form input as subsets. So in this case I am expecting the id value to show up as the values exist in the column, but this is not happending. Now say if I enter just CAT as the form input and perform the search, it should show me the ID 1 row. Now say if I enter just camel, cAT as the form input and perform the search, it should show me the ID 1 row. How can I achieve the above? Thank you.

  Read the article

• JavaScript Exception/Error Handling Not Working

  - by Seán Hayes

  This might be a little hard to follow. I've got a function inside an object: f_openFRHandler: function(input) { console.debug('f_openFRHandler'); try{ //throw 'foo'; DragDrop.FileChanged(input); //foxyface.window.close(); } catch(e){ console.error(e); jQuery('#foxyface_open_errors').append('<div>Max local storage limit reached, unable to store new images in your browser. Please remove some images and try again.</div>'); } }, inside the try block it calls: this.FileChanged = function(input) { // FileUploadManager.addFileInput(input); console.debug(input); var files = input.files; for (var i = 0; i < files.length; i++) { var file = files[i]; if (!file.type.match(/image.*/)) continue; var reader = new FileReader(); reader.onload = (function(f, isLast) { return function(e) { if (files.length == 1) { LocalStorageManager.addImage(f.name, e.target.result, false, true); LocalStorageManager.loadCurrentImage(); //foxyface.window.close(); } else { FileUploadManager.addFileData(f, e.target.result); // add multiple files to list if (isLast) setTimeout(function() { LocalStorageManager.loadCurrentImage() },100); } }; })(file, i == files.length - 1); reader.readAsDataURL(file); } return true; LocalStorageManager.addImage calls: this.setItem = function(data){ localStorage.setItem('ImageStore', $.json_encode(data)); } localStorage.setItem throws an error if too much local storage has been used. I want to catch that error in f_openFRHandler (first code sample), but it's being sent to the error console instead of the catch block. I tried the following code in my Firebug console to make sure I'm not crazy and it works as expected despite many levels of function nesting: try{ (function(){ (function(){ throw 'foo' })() })() } catch(e){ console.debug(e) } Any ideas?

  Read the article

• Center aligned form with equal width labels

  - by James Goodwin

  I have a very simple web form which consists of labels and input fields, however I can not seem to find a way of aligning the form in the center of the page and for the labels to have an equal width so that they appear neatly next to each other, one under the other. The structure of my page is basically: <body> <div class="form"> <form method="post"> <fieldset> <label>Mobile:</label><input type="text" name="msisdn"><br/> <label>Code:</label><input type="text" name="code"><br/> <br/> <input type="image" src="submit-button.gif" alt="Submit"> <br/> <input type="checkbox" name="ts_and_cs"><label> Accept Terms and Conditions</label> <br/><br/> </fieldset> </form> </div> </body> Usually I would fix this by doing float:left on the label fields and setting a width on the labels, however for this I need the labels and input fields to be centered on the page. Also I am not able to set the width of the page (or any containing divs) as the page will be displayed on mobile devices with different screen sizes. Any suggestions as to how best style the form? Thanks

  Read the article

• Build and migrated to software raid (mdadm) on GPT disk, now can't assemble array

  - by John H

  mdadm, gpt issues, unrecognized partitions. Simplified question: How do I get mdadm to recognize GPT partitions? I have been attempting to convert/copy my Ubuntu 11.10 OS from a single drive to software raid 1. I have done similar in the past, but in this case, I was adding in a drive that has been configured for GPT and I tried to work with that without fully looking into the implications. Currently, I have a non-booting mdadm RAID 1 array of /dev/md127 (the OS assigned that and it keeps picking up). I am booting off of live USB keys, currently System Rescue CD from sysresccd. While gdisk and parted can see all the partitions, most of the OS utilities do not, including mdadm. My main goal is just to make the raid array accessible so I can get pull the data and start fresh (without using GPT). /dev/md127 /dev/sda /dev/sda1 <- GPT type partition /dev/sda1 <- exists within the GPT part, member of md127 /dev/sda2 <- exists within the GPT part, empty /dev/sdb /dev/sdb1 <- GPT type partition /dev/sdb1 <- exists within the GPT part, member of md127 History: POINT A: The original OS was install on sda (actually /dev/sda6). I used a the Ubuntu live usb to add sdb. I got warning from fdisk about GPT so I used gdisk to create a raid partition (sdb1) and mdadm to create a raid1 mirror with a missing drive. I had many issues getting this working (including being unable to get grub to install) but I eventually got it to boot using grub on sda and /dev/md127 off of sdb. So at point A, I had copied my OS from sda6 to md127 on sdb. I then booted into a rescue mode and attempted to get a bootloader onto sdb, which failed. I then discovered my mistake: I had installed the raid onto sdb instead of sdb1, essentially overwriting the sdb1 partition. POINT B: I now had two copies of my data- one on md127/sdb, and one on sda. I destroyed data on sda and created a new GPT table on sda. I then created sda1 for the raid array, and sda2 for a scratch partition. I added sda1 into the raid array and let it rebuild. md127 now covered /dev/sdb and /dev/sda1 as fully active and synced. POINT C: I rebooted onto linux rescue again and was still able to access the raid array. I then removed /dev/sdb from the array and created /dev/sdb1 for the raid. I added sdb1 to the array and let it sync. I was able to mount and access /dev/md127 without issues. Once it completed, both /dev/sda1 and /dev/sdb1 were GPT partitions and actively syncing. POINT D (current): I rebooted again to test if the array would boot and grub failed to load. I booted off of my live thumb drive and found that I can no longer assemble the raid array. mdadm doesn't see the required partitions. -- root@freshdesk /root % uname -a Linux freshdesk 3.0.24-std251-amd64 #2 SMP Sat Mar 17 12:08:55 UTC 2012 x86_64 AMD Athlon(tm) II X4 645 Processor AuthenticAMD GNU/Linux === /proc/partitions and parted look good: root@freshdesk /root % cat /proc/partitions major minor #blocks name 7 0 301788 loop0 8 0 976762584 sda 8 1 732579840 sda1 8 2 244181703 sda2 8 16 732574584 sdb 8 17 732573543 sdb1 8 32 7876607 sdc 8 33 7873349 sdc1 (parted) print all Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 2 750GB 1000GB 250GB Linux/Windows data Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 Linux RAID raid Model: SanDisk SanDisk Cruzer (scsi) Disk /dev/sdc: 8066MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 31.7kB 8062MB 8062MB primary fat32 boot, lba === # no sda2, and I double the sdb1 is the one shown in parted root@freshdesk /root % blkid /dev/loop0: TYPE="squashfs" /dev/sda1: UUID="75dd6c2d-f0a8-4302-9da4-792cc7d72355" TYPE="ext4" /dev/sdc1: LABEL="PENDRIVE" UUID="1102-3720" TYPE="vfat" /dev/sdb1: UUID="2dd89f15-65bb-ff88-e368-bf24bd0fce41" TYPE="linux_raid_member" root@freshdesk /root % mdadm -E /dev/sda1 mdadm: No md superblock detected on /dev/sda1. # this is probably a result of me attempting to force the array up, putting superblocks on the GPT partition root@freshdesk /root % mdadm -E /dev/sdb1 /dev/sdb1: Magic : a92b4efc Version : 0.90.00 UUID : 2dd89f15:65bbff88:e368bf24:bd0fce41 Creation Time : Fri Mar 30 19:25:30 2012 Raid Level : raid1 Used Dev Size : 732568320 (698.63 GiB 750.15 GB) Array Size : 732568320 (698.63 GiB 750.15 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 127 Update Time : Sat Mar 31 12:39:38 2012 State : clean Active Devices : 1 Working Devices : 2 Failed Devices : 1 Spare Devices : 1 Checksum : a7d038b3 - correct Events : 20195 Number Major Minor RaidDevice State this 2 8 17 2 spare /dev/sdb1 0 0 8 1 0 active sync /dev/sda1 1 1 0 0 1 faulty removed 2 2 8 17 2 spare /dev/sdb1 === root@freshdesk /root % mdadm -A /dev/md127 /dev/sda1 /dev/sdb1 mdadm: no recogniseable superblock on /dev/sda1 mdadm: /dev/sda1 has no superblock - assembly aborted root@freshdesk /root % mdadm -A /dev/md127 /dev/sdb1 mdadm: cannot open device /dev/sdb1: Device or resource busy mdadm: /dev/sdb1 has no superblock - assembly aborted

  Read the article

• Use of 'this keyword' javascript in IE ?

  - by Ron

  Is there a workaround for Internet Explorer to implement the functionality offered by 'this' javascript keyword to get the dom element that triggered the event? My problem scenario is : I have a variable number of text fields in the html form, like input type="text" id="11" input type="text" id="12" .. I need to handle the "onchange" event for each text field, and the handling is dependent on the 'id' of the field that triggered the event. So far I understand that my options are: 1) attach a dedicated event handler for each text field. so if I have n fields, i have n different functions, something like: input type="text" id="11" onchange="function11();" input type="text" id="12" onchange="function12();" but the text fields are added and removed dynamically, so a better way would be to have one generic function instead. 2) use the 'this' keyword like: input type="text" id="11" onchange="functionGeneric(this);" input type="text" id="12" onchange="functionGeneric(this);" But this option does not work with Internet Explorer. Can anyone suggest a work around for getting it work in IE or some other solution that can be applied here? Thanks.

  Read the article

• Split internal USB pinouts - is it possible?

  - by TM

  I've currently got a situation in my PC where I have 3 devices that connect to the motherboard via the onboard USB pinouts. The problem is, I only have two sets of USB pinouts on my motherboard. Is there any way of connecting two devices to one set of pinouts? Essentially, I'm looking for the functionality of a USB hub, but I'd like it to be inside the case, and provide pinouts rather than regular USB ports. Update: I don't need any more USB ports, I have devices that use the USB pinouts. I already have extra USB ports that aren't used, so adding an PCI USB card doesn't really help anything.

  Read the article

• Get table row based on radio button using prototype/javascript

  - by David Buckley

  I have an html table that has a name and a radio button like so: <table id="cars"> <thead> <tr> <th>Car Name</th> <th></th> </tr> </thead> <tbody> <tr> <td class="car">Ford Focus</td> <td><input type="radio" id="selectedCar" name="selectedCar" value="8398"></td> </tr> <tr> <td class="car">Lincoln Navigator</td> <td><input type="radio" id="selectedCar" name="selectedCar" value="2994"></td> </tr> </tbody> </table> <input type="button" value="Select Car" onclick="selectCar()"></input> I want to be able to select a radio button, then click another button and get the value of the radio button (which is a unique ID) as well as the car name text (like Ford Focus). How should I code the selectCar method? I've tried a few things like: val1 = $('tr input[name=selectedCar]:checked').parent().find('#cars').html(); val1 = $("td input[name='selectedCar']:checked").parents().find('.cars').html(); val1 = $('selectedCar').checked; but I can't get the proper values. I'm using prototype, but the solution can be plain javascript as well.

  Read the article

• Submit Data to a datatable from a View MVC

  - by user54197

  I have a view that I would like to populate data when the next button is clicked. It is 3 Views which will send data on every next button. How do I do this? Below is code I just made up, but should give an idea of what I am looking for. Page 1: <table> <tr> <td><b>Name:</b></td> <td colspan="2"><input id="txtName" type="text" /></td> </tr> </table> <input type="submit" value="Next" /> Page 2: <table> <tr> <td><b>Address:</b></td> <td colspan="2"><input id="txtAddress" type="text" /></td> </tr> </table> <input type="submit" value="Next" /> Page 3: <table> <tr> <td><b>Phone:</b></td> <td colspan="2"><input id="txtPhone" type="text" /></td> </tr> </table> <input type="submit" value="Next" />

  Read the article

• Iphone 3GS to laptop Syncing

  - by Chris

  I use my Iphone calender to store all my appointments and customer information etc rather than my Outlook calender on my laptop most of the time. To the best of my knowledge I have never lost any info before, but after syncing the two devices today my calender is now empty on both. I had thought that syncing would mean taking the information on both devices, amalgamating it and populating both devices with the same info? Two questions: a) Is there anyway of retrieving the lost information? (or am I sunk?) b) Is there any way of averting such disaster in the future? Whilst I suspect that "Read the manual - Idiot!" would be the correct response, any help really is greatly appreciated!

  Read the article

• How do I access an Ubuntu VirtualBox guest at a static IP from an OS X host?

  - by David Siegel

  How does one configure an Ubuntu guest to use a static IP that's visible to an OS X host, and ensure that the static IP is independent of the host's network configuration? I previously used bridged networking for my guest, but I'm constantly moving my host between networks so the guest IP is always different. First, I tried setting the guest network configuration to NAT and forwarding host port 1022 to guest port 22, so I could at least ssh to a fixed address (localhost:1022): $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/Protocol" "TCP" $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/GuestPort" 22 $ VBoxManage setextradata "Ubuntu Server" "VBoxInternal/Devices/e1000/0/LUN#0/Config/SSH/HostPort" 1022 Then, $ ssh localhost -p 1022 ssh: connect to host localhost port 1022: Connection refused But this didn't work (guest has no network access with NAT and OS X refused the connection, as you can see). I'd love a general solution that would let me communicate with my guest at a fixed IP.

  Read the article

• How should I progressively enhance this content with JavaScript?

  - by Sean Dunwoody

  The background to this problem is that I'm doing a computing project which involves Some drop down boxes for input, and a text input where the user can input a date. I've used YUI to enhance the form, so the calendar input uses the YUI calendar widget and the drop down list is converted into a horizontal list of inputs where the user only has to click once to select any input as opposed to two clicks with the drop down box (hope that makes sense, not sure how to explain it clearly) The problem is, that in the design section of my project I stated that I would follow the progressive enhancement principles. I am struggling however to ensure that users without JavaScript are able to view the drop down box / text input on said page. This is not because I do not necessarily know how, but the two methods I've tried seem unsatisfactory. Method 1 - I tried using YUI to hide the text box and drop down list, this seemed like the ideal solution however there was quite a noticeable lag when loading the page (especially for the first time), the text box and drop down list where visibile for at least a second. I included the script for this just before the end of the body tag, is there any way that I can run it onload with YUI? Would that help? Method 2 - Use the noscript tag . . . however I am loathed to do this as while it would be a simple solution, I have read various bad things about the noscript tag. Is there a way of making mehtod one work? Or is there a better way of doing this that I am yet to encounter?

  Read the article

• SonicWall HA "gotchas"?

  - by Mark Henderson

  We're looking to move away from PFSense and CARP to a pair of SonicWall NSA 24001 configured in Active/Passive for High Availability. I've never dealt with SonicWall before, so is there anything I should know that their sales guy won't tell me? I'm aware that they had an issue with a lot of their devices shutting down connectivity because of a licensing fault, and they have an overtly complex management GUI (on the older devices at least), but are there any other big "gotchas" that I need to be aware of before committing a not insubstantial amount of money towards these devices? 1If you're outside the US, the SonicWall global sites suck balls. Use the US site for all your product research, and then use your local site when you're after local information.

  Read the article

• logitech unifying receiver

  - by Plastkort

  hi! I am having multiple logitech devices, and each and one of them seem to have theire own receiver, occupying USB ports.. I read upon Logitech unifying receiver, and it seem to connect multiple wireless devices from logitech, however I wonder if I just buy this one receiver, will I be able to connect my existing wireless devices, or will I be forced to buy new keyboard and mouse in order to use the unifying receiver? hope anyone here have the answer so I dont need to spend money on something I cannot use.. :) I got PC 1 Logitech Dinovo Edge keyboard Logitech MX Air mouse PC 2 Logitech Dinovo Keyboard Logitech VX mouse

  Read the article

• Why this class assignment is not working in IE

  - by user550750

  I've wrote this peice of code, this works fine in FF and Chrome but not in IE. Why is it? <html> <header> <style type="text/css"> .red{ color: red; } .green{ color: green; } .yellow{ color: yellow; } </style> </header> <body> <div id="mydiv" style="height: 50px">Some contents</div> <div> <input type="radio" value="1" name="change" onclick="onClick(this)">Red</input> <input type="radio" value="2" name="change" onclick="onClick(this)">Green</input> <input type="radio" value="3" name="change" onclick="onClick(this)">Yellow</input> </div> <script type="text/javascript"> function onClick(el){ var className = ""; if(el.value == 1){ className = "red"; }else if(el.value == 2){ className = "green"; }else if(el.value == 3){ className = "yellow"; } document.getElementById("mydiv").setAttribute("class", className); } </script> </body> </html>

  Read the article

• python gui events out of order

  - by dave

  from Tkinter import * from tkMessageBox import * class Gui: def __init__(self, root): self.container = Frame(root) self.container.grid() self.inputText = Text(self.container, width=50, height=8) self.outputText = Text(self.container, width=50, height=8, bg='#E0E0E0', state=DISABLED) self.inputText.grid(row=0, column=0) self.outputText.grid(row=0, column=1) self.inputText.bind("<Key>", self.translate) def translate(self, event): input = self.inputText.get(0.0, END) output = self.outputText.get(0.0, END) self.outputText.config(state=NORMAL) self.outputText.delete(0.0, END) self.outputText.insert(INSERT, input) self.outputText.config(state=DISABLED) showinfo(message="Input: %s characters\nOutput: %s characters" % (len(input), len(input))) root = Tk() #toplevel object app = Gui(root) #call to the class where gui is defined root.mainloop() #enter event loop Working on a gui in tkinter I'm a little confused as to the sequence the event handlers are run. If you run the above code you'll hopefully see... 1) Editing the text widget triggers the event handler but it seems to fire it off without registering the actual change, 2) Even when the text widget is cleared (ie, keep pressing BackSpace) it still seems to have a one character length string, 3) The output widget only receives its update when the NEXT event trigger is fired despite the fact the data came on the previous event. Is this just how bindings work in tkinter or am i missing something here? The behaviour i would like when updating the input widget is: 1) Show the change, 2) Enter event handler, 3) Update output widget, 4) Show message box.

  Read the article

• Reshape linux md raid5 that is already being reshaped?

  - by smammy

  I just converted my RAID1 array to a RAID5 array and added a third disk to it. I'd like to add a fourth disk without waiting fourteen hours for the first reshape to complete. I just did this: mdadm /dev/md0 --add /dev/sdf1 mdadm --grow /dev/md0 --raid-devices=3 --backup-file=/root/md0_n3.bak The entry in /proc/mdstat looks like this: md0 : active raid5 sdf1[2] sda1[0] sdb1[1] 976759936 blocks super 0.91 level 5, 64k chunk, algorithm 2 [3/3] [UUU] [>....................] reshape = 1.8% (18162944/976759936) finish=834.3min speed=19132K/sec Now I'd like to do this: mdadm /dev/md0 --add /dev/sdd1 mdadm --grow /dev/md0 --raid-devices=4 --backup-file=/root/md8_n4.bak Is this safe, or do I have to wait for the first reshape operation to complete? P.S.: I know I should have added both disks first, and then reshaped from 2 to 4 devices, but it's a little late for that.

  Read the article

< Previous Page | 154 155 156 157 158 159 160 161 162 163 164 165  | Next Page >