Search Results

Search found 6774 results on 271 pages for 'special locations'.

Page 159/271 | < Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >

• Router(s) Issue: DNS quries sporadically fail with multiple computers hooked in

  - by bob-the-destroyer

  Basically, after anywhere from 5-60 minutes, DNS queries fail for a few minutes, then slowly begin to resolve correctly. Then the cycle repeats. This occurs only when more than one computer is on the network. All computers on the network experiences the same sporadic DNS outage at the same time. Wireless or wired, Linux or Windows, fresh OS install or old, browser or ping, same symptoms. Duplicated on 3 routers (not chained together, mind you) and 3 ISP's and 3 separate locations over the past several months. The only common theme is a single 5-yo WIN XP laptop which has been in use on the network throughout all this. There also may be anywhere between 1 - 10 devices hooked up wired or wirelessly at a time. The only reprieve I have from this torture is by using any VPN to an outside source - always smooth sailing. I typically set up any router to a) use WPA2/etc security; b) MAC whitelist; c) UPNP OFF (if available); d) always update firmware when available; e) obtain DNS from ISP automatically; f) set the router to act as DHCP server for the internal network. Adjusting channels has no effect. Any ideas?

  Read the article

• pgpool2+streaming replication failover on only 2 servers?

  - by aneez

  I am trying to configure pgpool2 and postgresql 9.1 to handle failover. I currently have streaming replication running, and are using pgpool2 for read-only load balancing. I have 2 servers in my setup, both running postgresql - 1 master and 1 slave. The master is also running pgpool2. My question is how do I configure this setup to handle failover? Specifically in the case that the master crashes, and the slave has to take over and run pgpool2 as well. Most documentation and examples I have been able to find assumes that pgpool2 is running on a separate server and thus "never" crashes. I may or may not be attacking the problem using the wrong tools. In my production setup I have a total of 3 identical servers all in independent locations. The main goal of the setup is to achieve a high uptime. Thus failover should be automatic, and bringing a failed node back up should cause only minimal downtime. I want all 3 nodes to be as close to identical as possible, and be able to run with just 1 or 2 nodes available. And if possible I want to use load balancing to improve performance. If anyone can help me gain some insight into how to do this using my current setup or suggest a different/better setup. Thank you!

  Read the article

• How do I know if I managed to completely remove an undetected trojan?

  - by ubuntuisbetter

  I catched a trojan that uses explorer.exe to reproduce itself in case of deletion of its autostart entry or main exe file in Programs/x. It had already tried to contact a suspicious server over explorer.exe, blocked that via my firewall. I: Removed the autostart entries from the registry Looked through my services if there was anything suspicious Deleted the trojan from Programs/ Went through System Volume Information to find a 2 month old explorer.exe and replaced the possibly infected one. There are no suspicious processes running now anymore (no duplicate explorer.exe) and nothing wants to connect this trojan owners sever either. I checked my system with several anti-malware programs too. What the trojan did: Started a second explorer.exe Always when I deleted the main trojan exe file it was reproduced (by the second explorer.exe) Always when I deleted the autostart entry it was reproduced by the explorer.exe too. When I terminated the suspicious explorer.exe, which used only half as much memory as the less suspicious one from Windows, a strange thing that I know from the computers in my Informatics class happened: A window popped up in the top left of my explorer-less desktop, titled "Personal settings for ... are ..." that obviously copied some files. Then both explorer.exes started again and the trojan was everywhere again. What did the trojan actually do to get explorer to rescue it? Is my PC clean of this newish trojan now? What are the other locations I should check for the trojan? The trjoan doesn't seem very high-level, could it have changed other system files or is the autostart entry vital for it? Thanks in advance, Your trojan paranoid friend (Getting linux in a week)

  Read the article

• How many bootable partitions are possible to have on one hard drive?

  - by draiden

  This may not be the correct place to post this; if that's the case, just let me know and point me in the right direction please! I'm thinking of building a box that needs to be lightweight and portable, and would need to be able to boot multiple installations of windows. I am needing to have multiple installations so that I can, for example, plug the box in to the network at one location, boot in to that location's partition, and have full access to everything I would normally need to do on a computer that has already been set up on that network. Then, when I go to the next client, I would be able to do the same thing, with the new location's partition, and have all of those network settings, drive mappings, etc., available there. Obviously I'd need to go through and set them all up on the different locations/networks, I'm not expecting it to magically know where I am and what I'm doing. It would be like I'm carrying around a computer that is configured for each place I need to go in one little box, instead of having to have multiple computers or having to reconfigure all the settings and such every time I go to another client. Or is there an easier way to do this that I haven't learned of?

  Read the article

• Is it possible to add a WiFi HotSpot to an already established LAN, keep the two separate, and not modify the primary router?

  - by user12844

  I have a set up where my Cisco ASA is sitting in one facility, providing access to the Internet for two buildings. The two buildings are geographically separated by a Wireless Bridge spanning about 10 miles. All computers and equipment inside the LAN are on the same subnet (its pretty small) and we have WiFi AP's in both locations providing Wired and Wireless access to the LAN. Given all the BYOD (Ipods, and SmartPhones etc...) coming into the office as well as Visiting reps etc... we would like to also provide a non-secure, device independent (the devices cannot see or communicate with each other), and LAN independent (the devices cannot see or use anything on the LAN) HotSpot that anyone could use for their Devices that gives them access to the Internet ONLY without needing a password. I get that this could be possible at the facility with my Cisco if I messed with it and created VLANs etc... but then I would need to get it across my Bridge as well and don't think that would be possible without serious reconfiguration of everything. Would really like some kind of magic drop in solution that can kind of piggy back on my LAN without really needing to do very many if any changes to the current set up.

  Read the article

• How To Completely Move Users/Program Files/Program Files (x86)/ProgramData (Folders) To Another Partition(s) On Windows 8?

  - by Enigma83

  I am attempting to move folders Users Program Files Program Files (x86), ProgramData (at the root of the C drive) to at least 2 other partitions, preferably on a fresh install. I have read that there are methods for doing this post-install, but it seems like it would be a bit more tedious to do things that way. I want to move the 2 Program Files folders to another partition on the same HDD, and Users/ProgramData will go to yet another partition on same HDD. I have done a bit of research on this, read up on some things that involved booting into Audit Mode, using the RoboCopy command to copy folders via booting into my Windows 8 USB drive, creating NTFS junctions/symbolic links, Registry edits, as well as accomplishing this automatically by creating an auto-attend file which Windows Setup processes automatically before the user is ever booted in for the 1st time. I tried this morning and now have a basic installation in which programs like Internet Explorer fail to open, certain files can't be found/opened (even if I click on them directly), an example is Regedit. Also, I can't run the Command/DOS (CMD) prompt as Administrator (or otherwise, as any other user), can't activate the real Administrator account or open any of the Administrative Tools (despite having added them to my Start Screen). So far I have only tried RoboCopy-ing Program Files and Program Files (x86) so far, creating junction points for them, and editing the Registry in the relevant locations. This is what I'm left with now. I also found the following blog article which describes how to do this for Windows 7 So, where should I go from here and where can I find more information? And how can this be done without disabling the Metro apps, which I've read will stop working if you move ProgramData. Once I have everything moved, where do I install programs to? Do I tell them to install to C:\Program Files\Program Files (x86) or to the junctioned/symbolic-linked partition/drive? I plan to test in VMware virtual machines from here on until things are working correctly, while using a baseline default install for daily tasks.

  Read the article

• Have some questions about setting up a VPN to my private cloud servers

  - by Pure.Krome

  I've got a number of Virtual Servers running at a pretty big Cloud provider. They are all running Windows 2008 R2. I have a CISCO ASA firewall in front of them. Currently, I've got all ports blocked except 80/443/21/3386 (for Remote Desktop). I asked to have a VPN enabled on the firewall and they said it's easy to do BUT I need to use the 3rd party Cisco software. Now, I don't want to get into a debate about it .. but we don't want to install anything extra on our -client- computers. We all use Windows 7 and we love using the built in VPN client to connect to other private LANS we have setup in other locations. So i'm wondering what options I have to create a VPN tunnel to our private cloud LAN? All our cloud servers are part of WORKGROUP, so there's no Active Directory .. nor do we want to install all that. Secondly, we know we can open up a firewall port - so any ports for starting a VPN is fine! Lastly, I was thinking of just using one of the existing servers as the VPN server (and using the Windows VPN software) .. but I'm not sure this is a good thing? Remember - we just want to use the baked in VPN software in Windows 7 .. which is PPTP or SSTP or L2TP/IPSEC. I would -LOVE- to use some free OSS software. For usernames/passwords? We'd probably just have one account .. like U:Hithere P:whatever.. so we don't need any hardcore account management, like Active Directory, etc. So does anyone have any ideas?

  Read the article

• Sizing Switches for Storage and Production

  - by Untalented

  Couple questions. Should you always completely separate the storage network switches from production switches or are VLANs fine to segment this traffic? Is there a golden rule here? How do you properly size a switch for your environment based on the specifications the manufacturer provide (Throughput, Forwarding Throughput, Stacking Throughput, Max Mac)? If you have two switch options and one has a maximum Mac address of 8,000 vs. another with 16,0000. What does this really mean to me? How do make sure one vs. another is sized properly for me? Besides VLAN and Jumbo Frame support, is there any other "Must" haves for a virtual environments production or storage networks? There is a wealth of knowledge on sizing SANs and such, but this seems equally important and it's quite challenging to find as much information. -- Just to add some tidbits of information for the environment. This setup above is referring to the data centers which supports two different locations which have about 100 users between the two in total. The storage traffic will be iSCSI and will be 3 ESXi Hosts and one SAN housing about 2.7TB of data. Since there is currently no storage network in place (no SAN), I'm having a hard time regarding #2 to really determine what backplane throughput and switch specifications will be sufficient.

  Read the article

• Windows Vista Context Menu>New... does not find entries

  - by Paul

  I was trying to remove a virus and foolishly did not backup registry keys I deleted because I (thought) I only deleted entries from the folders of programs I did not care about. However, I think I have done something wrong here: Now when I open a context menu (right click) in any location and hover over the "New..." option I don't get any options. It has a greyed out box saying "(Empty)". So far I have found out the the entries themselves are still there (using the locations provided here: Windows 7 - Add an item to 'new' context menu). I have also used a program recommended in that thread which also finds the entries intact and enabled. So it seems maybe I have deleted the entry which tells Vista where to look to find the files that can be created. How can I restore this so entries are shown again? I know system restore is an option but as I have said I did this when removing a (very stubborn) virus so that is the last resort.

  Read the article

• nginx configuration file explained

  - by Chris Muench

  I have a few questions about this configuration file "default" in /etc/nginx/sites-enabled. It is shown below. server { root /usr/share/nginx/www; index index.html index.htm; # Make site accessible from http://localhost/ server_name localhost; location / { proxy_pass http://127.0.0.1:8080; } location /doc { root /usr/share; autoindex on; allow 127.0.0.1; deny all; } location /images { root /usr/share; autoindex off; } } There is no "Listen" directive, how does it know to default to 80 The server_name is localhost, how does another domain work? Why is the location directive embedded in the server directive? Does that mean these locations ONLY apply to this server? None of my configs have listen 80 default_server; how does nginx then pick what configuration to use?

  Read the article

• Difference between "bit-number" in filesystem and that in OS (like 32,64 bit)?

  - by learner

  I encountered 2 terms ,"FAT32", a file system and "Windows Vista 32 bit". I found that the meaning of a 32 bit OS is that that the OS deals with data in chunks of minimum size 32 bits. I don't quite understand the depth of that, but I figure ,every file in that system with that OS should have a minimum size of 32 bits. I also read that these 32 bits are used to hold data of files' location(reference) and details. Which of it is it? I have also read that 4 GB of RAM is all that is needed at the most if you're on a 32 bit OS. But I don't understand why. If there are 32 bits to hold info about files and their locations,there can be 2^32 possible combinations of it. But I have found in many places,2^32 is divided by 1024 thrice to get 4GB. Why? Did that 2^32 become equal to 2^32 bytes? And about filesystems I read a similar explanation for what 32 means in FAT32. It is supposed to mean that 32 bits are used to number file system block. Now how is different from the number before the OS?

  Read the article

• Set up layer 2 vlan between 2 data centres

  - by user41679

  Hello, Our data centre provider operates 2 sites, and we currently have equipment in one and would like to have equipment in the second. They've told me that they operate a layer 2 vlan between the 2 sites over a 20gbit connection, and that they'd just give me ethernet cable at each end to connect the locations. At the current site, we have Cisco 2960 48TC-L switches, all the machines are on a 192.168.x.x subnet and we have cisco firewalls with which we connect to our internet provider with. My question is what would I need to do to connect the 2 sites? could I just plug the ethernet cables the provide into the cisco switches, and have the same switches the other end? would I need to set up a separate internal network on the other side and connect both through the firewalls? Would the cisco switches need special configuration? We expect to maintain a number of connections between the 2 sites, and each site would have its own internal dns name like dc1.xx.com. Sorry if I'm being vague or haven't included enough information, I've a fairly good knowledge of hardware but we're down a netops guy at the moment and I'd like to get both sites on-line ASAP! Thanks in advance!

  Read the article

• Image Management System with Different Levels of Access

  - by Jason

  I work in the graphics department for a real estate brokerage, and we deal with a lot of photos. Agents take the photos, upload them to me, I touch up and standardize the photos, then I add them to an in-house server for future use by the graphics dept. I'd like to make the "sanitized" photo files available to the agents to use when they want, but I don't want the agents poking around the graphics department's files (things get misplaced, renamed and messed up in a hurry). What would be perfect is if we could create a read-only "mirror" (correct term?) of that server that could be accessed by the agents as needed, but which wouldn't feed back into our "sanitized" file system. Edit: I'm looking for an automatic solution... manually posting the files to two separate locations seems like an inelegant solution when working digitally. Edit: I'm trying to avoid any access barriers to the public (dirty) file system (however it's finally implemented). There are 40-50 real estate agents who need to access these files, half of whom can't reliably download an email attachment.

  Read the article

• How to access files on a USB-connected NTFS disk removed from a Win7 notebook?

  - by yosh m

  My daughter seems to have fried her motherboard in her Lenovo Notebook. The disk seems to be fine. I removed the disk and used a universal disk-to-USB kit to attach it to another computer. The disk is recognized fine and I can peruse it in Windows Explorer. The problem is that the files she would like to recover from it are located in places that Windows refuses to let me access. When I try, for example, to enter the directory "Documents and Settings" it gives me an "Access is denied" error. Same thing when I try to go into the various User directories and other locations. I thought to try creating a Ghost image & retrieve the files from that, but Ghost seems to croak when I try to run it - apparently it doesn't like accessing the disk via a USB connection (even though I've told it to install the drivers for USB). Any other ideas about how to get to the files I need, either through Windows or perhaps some other OS that I could boot from a CD that can read an NTFS disk? Thanks, Yosh

  Read the article

• How can I find which logon script is being run?

  - by user2517266

  I'm having an issue with network drives. Suddenly some computers and users aren't getting their mapped network drives from the logon script. I am NOT a domain admin, I don't have permission to login to the domain controller. And I know very little about Active Directory. The issue seems random, some users this day, different users tomorrow. Some computers run fine and some won't map no matter who logs in. They are mixed OS's XP (SP3), Vista, and 7. I was looking at the domain in windows explorer and I have found the batch file(s) that maps the drives in several locations, how do I know which one is actually being ran? The .bat file is located in \DOMAIN\NETLOGON\script.bat and \DOMAIN\SYSVOL\DOMAIN\scripts\script.bat and \DOMAIN\SYSVOL\DOMAIN\policies\GUID(Right? It's a crazy string)\User\Scripts\Logon\script.bat So, how can I figure out which one is actually being ran per computer or user? Cause they are all slightly different from each other and one of them doesn't map properly. Do all the files in NETLOGON get ran? Cause there are 15+ files in there. Or is it specified in Group Policy which one(s) get ran? EDIT: I am able to access a program called Active Directory Users and Computers, but the properties tab for any user is blank for the logon script.

  Read the article

• How many bootable partitions are possible to have on one hard drive?

  - by draiden

  This may not be the correct place to post this; if that's the case, just let me know and point me in the right direction please! I'm thinking of building a box that needs to be lightweight and portable, and would need to be able to boot multiple installations of windows. I am needing to have multiple installations so that I can, for example, plug the box in to the network at one location, boot in to that location's partition, and have full access to everything I would normally need to do on a computer that has already been set up on that network. Then, when I go to the next client, I would be able to do the same thing, with the new location's partition, and have all of those network settings, drive mappings, etc., available there. Obviously I'd need to go through and set them all up on the different locations/networks, I'm not expecting it to magically know where I am and what I'm doing. It would be like I'm carrying around a computer that is configured for each place I need to go in one little box, instead of having to have multiple computers or having to reconfigure all the settings and such every time I go to another client. Or is there an easier way to do this that I haven't learned of?

  Read the article

• Is is possible to guide installation of new programs using %ProgramFiles%? [closed]

  - by ??????? ???????????

  The purpose of this is to have the default "program files" (32 and 64 bit) folders located under an arbitrary path, possibly on a drive separate from where windows lives. Initially I thought that this may be done using a system environment variable through the dialog located under Control Panel - System - Advanced - Environment Variables. These variables turned out to be set in the registry under the key HKLM\SOFTWARE\Microsoft\Windows\CurrentVersion. However, one particular entry is confusing. The ProgramFilesPath entry seems to point at an environment variable that is not defined under the same registry key. I could assume that the difference between ProgramFilesDir and ProgramFilesPath is none and that one of them exists as a backwards compatibility, but having some legitimate resource from Microsoft to look at would be better than guessing. After receiving some worrying feedback about having both 32 and 64bit applications in the same folder, I have decided not to ask about the feasibility of this to avoid discussion. The real question is if the desired effect is possible to attain by "cutting into" the windows setup process and modifying those registry entries as early as possible. These settings should be system wide and not only for software installed by a particular user. If this is indeed something that can be done, I wonder if there are any subtle pitfalls. Programs that expect libraries and other resources to be in default locations can probably be dealt with using the same technique as employed by Windows to re-map the "Documents and Settings" folders and the like (i.e. breaking legacy applications is not real concern).

  Read the article

• Efficient mirroring of directories using hard links [closed]

  - by zoqaeski

  I'm backing up my music collection on to a number of NTFS-formatted external hard-drives; however, as I store my main collection in FLAC and have my library on my laptop as MP3s to save space, I want to be able to back up both sets, because mass conversion between formats is time-consuming. The "music" directory can contain any format; the "mp3s" directory contains only MP3s converted from files in the "music" directory. The music collection on the laptop contains only MP3s, but they come from both sources. When I backup my laptop's library to the "mp3s" directory, I want to only copy across MP3 files that don't exist in the "music" directory; those that do should be hard-linked to the "music" directory. All directories have an identical hierarchy, sorted by artist, album, date, discnumber if applicable, etc, and I use a tagging editor to ensure consistency across all these locations. I'm also using a Linux computer, but keeping the music collections on NTFS-formatted partitions so that they are readable by both Linux and Windows. At the moment, I use the following command to perform the backups, but this is time-consuming due to the expensive nature of finding hard links. rsync -avu --progress --relative --ignore-existing --link-dest=../music/ **/*.mp3 /media/ntfspocket/mp3s Is there a way to perform this backup more efficiently, taking advantage of the directory hierarchy?

  Read the article

• Android Webview Anchor Link (Jump link) not working

  - by Joel

  Hi, I have a WebView in my Android App that is loading an HTML string using the loadDataWithBaseURL() method. The problem is that local anchor links (<a href="#link">...) are not working correctly. When the link is clicked, it becomes highlighted, but does not scroll to the corresponding anchor. This also does not work if I use the WebView's loadUrl() method to load a page that contains anchor links. However, if I load the same URL in the browser, the anchor links do work. Is there any special handling required to get these to work for a WebView? I am using API v4 (1.6).

  Read the article

• Passing multiple parameters in an MVC Ajax.ActionLink

  - by mwright

  I am using an Ajax.ActionLink to call an Action in a Controller, nothing special there. I want to pass two parameters to the Action. Is this possible using an Ajax.ActionLink? I thought that it would just be a matter of including multiple values in the AjaxOptions: <%= Ajax.ActionLink("Link Text", "ActionName", "ControllerName", new { firstParameter = firstValueToPass, secondParameter = secondValueToPass }, new AjaxOptions{ UpdateTargetId = "updateTargetId"} )%> Is it possible to pass multiple parameters? Where is a good place to learn more about the AjaxOptions?

  Read the article

• TTThumbsViewController + navigationController issue

  - by michael

  Hi, .. 2 questions. I am only using Three20 for a gallery in my app. When I push my .. : TTThumbsViewController from another view, the navigation bar is not the color I want it to be (as per the rest of my app). I have set up a TTDefaultStyleSheet as per this stackoverflow QA. Is there something special I have to do as I am only using the TTThumbsViewController? The thumbs view is also created with extra space at the top, as though it is leaving room for a navigation controller, without knowing that one is already there. How can I tell the TTThumbsViewController to use the existing uinavigationcontroller? Or behave as though it is? MYThumbsViewController *mYThumbsViewController = [MYThumbsViewController alloc]; [self.navigationController pushViewController:mYThumbsViewController animated:YES]; The problem depicted graphically: Thanks!

  Read the article

• How to organize Python modules for PyPI to support 2.x and 3.x

  - by Craig McQueen

  I have a Python module that I would like to upload to PyPI. So far, it is working for Python 2.x. It shouldn't be too hard to write a version for 3.x now. But, after following guidelines for making modules in these places: Distributing Python Modules The Hitchhiker’s Guide to Packaging it's not clear to me how to support multiple source distributions for different versions of Python, and it's not clear if/how PyPI could support it. I envisage I would have separate code for: 2.x 2.6 (maybe, as a special case to use the new buffer API) 3.x How is it possible to set up a Python module in PyPI so that someone can do: easy_install modulename and it will install the right thing whether the user is using 2.x or 3.x?

  Read the article

• Which datagrid to use for ASP.NET MVC2 project?

  - by Nick

  Hi, I am developing a commercial MVC2 app that requires a grid that has callback update in some form to support 10,000+ rows. It should also support relatively rich content (icons, multiline descriptions etc). Although it requires the usual paging/scrolling/sorting features it does not need support for grouping. So nothing that special. The commercial grids I looked at were Component Art (http://www.componentart.com/products/aspnetmvc/datagrid/) and Telerik (http://www.telerik.com/products/aspnet-mvc/grid.aspx) which both look pretty good but may be a little OTT for what I need. They are also $800 and $999 respectively (1 developer). I've also looked at jqGrid (http://www.trirand.net/download.aspx) and the grid from MvcContrib. These appear ok but for a commercial app I am concerned that these may be risky options - though could be wrong there. I'd really appreciate any views/exprience on either the above grids or perhaps you can suggest a better option/approach. FYI I am using EF4 and C#. Cheers

  Read the article

• logback with EJB3.1

  - by kgrad

  I am using logback/slf4j to handle logging in my application. Everything was working perfectly until I started using EJBs. Once I added a stateless EJB to my app, the logger started ignoring my logback.xml and stopped using my appenders. I switched to a programmatic logger configuration to see what was wrong and now I am getting the following error when I try to use my logger within the EJB: org.slf4j.impl.JDK14LoggerFactory cannot be cast to ch.qos.logback.classic.LoggerContext stemming from the line: LoggerContext lc = (LoggerContext) LoggerFactory.getILoggerFactory(); Is there any special configuration necessary to get logback to work with EJBs? If it matters I am deploying on glassfish v3.

  Read the article

• How to organize Python modules for PyPI to support 2.x and 3.x

  - by Craig McQueen

  I have a Python module that I would like to upload to PyPI. So far, it is working for Python 2.x. It shouldn't be too hard to write a version for 3.x now. But, after following guidelines for making modules in these places: Distributing Python Modules The Hitchhiker’s Guide to Packaging it's not clear to me how to support multiple source distributions for different versions of Python, and it's not clear if/how PyPI could support it. I envisage I would have separate code for: 2.x 2.6 (maybe, as a special case to use the new buffer API) 3.x How is it possible to set up a Python module in PyPI so that someone can do: easy_install modulename and it will install the right thing whether the user is using 2.x or 3.x?

  Read the article

< Previous Page | 155 156 157 158 159 160 161 162 163 164 165 166  | Next Page >