Search Results

Search found 665 results on 27 pages for 'ghz'.

Page 16/27 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

  • How do I debug an overheating problem?

    - by Tab
    Hello guys. I have a problem with my Laptop (Dell Inspiron 1564 Core i5 4GB Ram VGA ATI Mobility Radeon HD 4300 running Ubuntu 10.10 32bit). It shuts down abruptly without even a lag in the application I am working with before shutdown. I think it's overheating problem. Actually the laptop is hot all the time when I am running Ubuntu. When I switch back to windows, even with intense load it won't shutdown or show any problem as long as I keep proper ventilation (when the air openings are blocked it does the same). Actually on Ubuntu i don't usually do things that need much CPU power, usually surfing internet, coding web pages and sometimes playing with python and ruby. I am not enabling desktop effects so no GPU load except the normal GNOME gui. Now as I am writing the Processor load in the panel monitor applet is 0%, Memory 11% by programs, 22% by cache. And i have CPU Frequency monitor for each of the 4 cores set to 1.20 Ghz (the lowest possible value, i am not sure if this applet does really limit CPU usage). Running sensors in terminal gave me temp1: +26.8°C (crit = +100.0°C) temp2: +0.0°C (crit = +100.0°C) hddtemp /dev/sda at the terminal gave me /dev/sda: WDC WD3200BEVT-75ZCT2: 46°C All that fine but the laptop is Really hot i can feel it in the keyboard, mouse pad is painful to touch, and the fan is always spinning. I am also placing 2 small fans running on USB under the laptop right now and the laptop is lifted over the fans so it's well ventilated. When I am running windows it doesn't get that hot except when there is a really big load on the CPU and this is keeping me away from using Linux for everyday tasks. Actually I don't care much for speed as I can deal with low speed it's not going to shutdown abruptly. So please if you can help me and tell me what are the possible causes, where should I start ?

    Read the article

  • Macbook Pro (SantaRosa) internal display not detected by graphics card, external monitor OK

    - by BLAU
    My MacBook Pro (2.4 Ghz, Santa Rosa with infamous nVidia card) acts strange. It shows the normal gray screen with Apple logo and animation flawlessly during start up but the internal display goes black without any rendering at all when all is loaded. (shining a light on display show nothing) If an external monitor is connected through the DVI port it will remain black during start up and then show the desktop as the internal display goes black. This happens both while booting to Mountain Lion and Windows XP. I have checked "About my Mac" and only the external display is listed. The same is the case if I use the nVidia Control panel in Windows XP. My questions: Is this a hardware problem or is it related to software maybe even firmware? What controls the display during start up, graphics card or something else?

    Read the article

  • Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

    - by user1622959
    A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

    Read the article

  • Not able to connect to internet in RHEL 5

    - by chankey007
    I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

    Read the article

  • Not able to connect to internet in RHEL 5

    - by chankey007
    I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

    Read the article

  • What can I do to utilize all my hard disk space?

    - by Twatcher
    I had windows XP running on my computer. Then I installed Ubuntu from under windows. Then I decided I wanted to have only Ubuntu also because I got a system message that I am out of disk space. I loaded up my system from a live Ubuntu DVD and deleted the partition with windows on it and also the other partition that had my data on it. I expanded the partition which I thought to be the system partition (since there was no other partition left It had ext format. After that Ubuntu was working fine and I thought I have enough disk space, since my harddrive is an 80 GB ATA Maxtor. I left a small partition as backup. But after downloading a small amount of files I got the message again, that I am running out of disk space. I don't now. How can UI make my disk space bigger? I am not used to Ubuntu's file system, and I don't have the overview on how I can actually see how much space there is left for me to use. I have basically now 1 partition with the system on it and one small backup (as far as I understand). My system is (from system utility) Ubuntu 12.04 LS 3,9 GB Intel Core 2 2,4 Ghz 80 GB ATA Maxtor Here are the results for sudo fdisk -l Disk /dev/sda: 80.0 GB, 79998918144 bytes<br> 255 heads, 63 sectors/track, 9725 cylinders, total 156247887 sectors<br> Units = sectors of 1 * 512 = 512 bytes<br> Sector size (logical/physical): 512 bytes / 512 bytes<br> I/O size (minimum/optimal): 512 bytes / 512 bytes<br> Disk identifier: 0x41ab2316<br> Device Boot Start End Blocks Id System<br> /dev/sda1 * 63 123750399 61875168+ 7 HPFS/NTFS/exFAT<br> /dev/sda2 123750400 156246015 16247808 7 HPFS/NTFS/exFAT<br>

    Read the article

  • 11.10 install hangs at different places

    - by TreefrogInc
    I've been trying to install Oneiric for some time now, and I've looked everywhere for a solution to the problems I've been having. So far, I've attempted four times to install it, so now I'm up to a point of panic. So I grabbed the 11.10 x64 iso from the website, and after verifying that the md5 hash is correct, I burned that onto my last remaining clean CD. On my first attempt, everything went perfectly up to the middle of the installation, and the progress bar stopped when it said: "configuring target system." I could do everything else, only the installation seemed to have stopped. After I googled my problem, I went and used the "check disc for errors" option, which said everything was fine. Then I tried the installation again, only this time, I selected "Install Ubuntu Now" instead of the "try before installing". Again, the same problem. My second and third tries didn't even reach the installation phase. It just stopped at the 5 blinking dots and never went any further. I used the same non-rewritable cd for all the attempts, as the error check didn't show any problems and because I'm currently out of usable cds. System: Core i3 CPU @ 3.4 GHz, 500 GB HDD (250g used for Win7, 70g used for preexisting system partitions, 180g unallocated).

    Read the article

  • DVI to HDMI - displaying bad.

    - by TutorialPoint
    I currently have a computer with a ASUS EAH5770 (ATi Radeon HD 5770) 1GB GDDR5 video card, and 4GB ram, 2.6 GHZ i5 processor. I just switched from a DVI (the blue one) to an HDMI cable. (Bigben Flat cable HDMI 1.3c) I use a Samsung SyncMaster 2032 MW, which has a HDMI input. The weird thing is, that my screen is off-the-corner of the tv (so it's too wide) (1920x1080), and windows icons and text are not displaying well, though 1080p videos in YouTube are looking brilliant, just like pictures. So i think it has something to do with Windows. I already have the ATI Catalyst Control Center with the drivers i received with my video card. I do not currently know how to fix these problems. Do i have to reinstall Windows or so? Or is it (hopefully) easier?

    Read the article

  • Why am I seeing excessive disk activity when installing applications?

    - by Kev
    I'm running Windows 7 Ultimate 64 bit on a Dell Vostro 1720 with 8GB of RAM, 7200RPM Disk, 2.53 GHz Core2Duo (Windows 7 64 bit is a supported option and the laptop came with the OS pre-installed). I'm noticing some fairly excessive disk activity when running installers. For example the Visual Studio 2010 RC installer constantly accessed the disk for ~10 minutes. It was so excessive that I was unable to use the machine until this ceased. Today I installed Trillian Astra 4.1 for Windows (latest build from the website). Again when I ran the installer I was pretty much locked out of the machine until the disk activity calmed down. In both cases when I eventually managed to launch task manager I could see that the CPU was sitting at around 5% to 7% utilisation whilst this was going on. All other disk related activity is fine, the machine is snappy and applications launch without delay. It's just when I run an installer I see this odd behaviour. Why would this be?

    Read the article

  • How do I lower idle cpu usage in ubuntu linux? Gnome or KDE Variants

    - by Jasen
    My question comes from a kde desktop currently, but it also happens with the gnome instance. When just sitting there, with only the cpu monitor widget running. no open windows, no background processes other than the desktop, my cpu is at ~20%. I wanna know how to fix this, and possibly get better performance out of it. When running my windows side, the cpu will sit at zero, and i generally load new programs about 400ms faster. With windows 7 being as slow as it is, this is not acceptable. and the widget is only set to check every 500ms, so im almost completely sure its not the widget. My system is a Gateway nv 53 amd 2.0 ghz turion with 4 gb of installed ram, and 500 gb hd. both linux and windows are 64 bit. average ram use on either system is about 1.4 gb for just the os

    Read the article

  • How to minimize services in ubuntu

    - by codeomnitrix
    Hello everyone.I am using ubuntu from last 6-7 months. I am having 512mb ram and a p4 processor with 1.73 Ghz processing speed. And being a programmer i have to work with eclipse and netbeans like ide's, and they sometimes hang. So is there any option in ubuntu to stop the services running just like i do have in windows "msconfig" or mycomputer-manage, and where could i find the details about the services so that i should know what will be its effect if i stop this service. I am using ubuntu 10.10 Thanks

    Read the article

  • What affects video encoding speeds?

    - by Pig Head
    FRAPs doesn't compress its videos when you record, so the files are enormous. In a long recording you can get up to a few hundred gigabytes. Obviously, usually you would need to convert/compress them. What affects the speed of this? I don't think the RAM does, as when I converted 600 gb my RAM usage only went to 6 gig, but the processor was at 100%, which is surprising as I have a 6 core processor @ 3.46 ghz. Would clock speed or cores help the most?

    Read the article

  • My internet connection slows or dies unexpectedly

    - by genesis
    I installed Ubuntu 10.04 once again and I'm having some problems which I had before, but I have no idea how I solved them. On Windows, everything's working fine and I had no problems with this. My problem is that sometimes, when browsing through the internet, webpages just start to load really slow, sometimes it doesn't load anything at all (Error 118 (net::ERR_CONNECTION_TIMED_OUT): The operation timed out.) and it starts to work after few minutes. My IPv4 settings are automatic (DHCP), and IPv6 settings are Ignored/Disabled. I think my previous problems had something to do with IPv6, but I'm not sure. Is there a fix for this? iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Fsite1" Mode:Managed Frequency:2.442 GHz Access Point: C8:3A:35:40:43:68 Bit Rate=0 kb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=43/70 Signal level=-67 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0

    Read the article

  • Why does my CPU Usage reach 100% too often?

    - by deathlock
    I'm using a dual-core processor and often see my CPU usage reaches 100%. I realize this may happen if I'm running too much applications, so when I know the computer starts to run slowly, I start to close my applications. I usually run 4-5 applications simultaneously. Usually those are: web browser (Google Chrome), Adobe Photoshop, Notepad++, XAMPP, and Windows Task Manager. Usually I close tabs in my Chrome first, because I often browse the net with about 20 tabs/4 windows open, so I presume that would take much memory (bad habit, I know). But even after closing Chrome's tabs or closing other applications, my CPU Usage often stays at high percentage - 72% at best, 100% at worst. I check the Processes tab on Windows Task Manager and usually found the System, System Idle Process, or services.exe taking the highest CPU process (could reach 60). Why is this happening? And is there any solution? EDIT I have T2250 @ 1,73 Ghz and 2.5 GB RAM

    Read the article

  • Why doesn't my computer work at full speed?

    - by kubilas
    My motherboard is a Gigabyte GA-8I915PL-G with an Intel Pentium 4 630 3,0 GHz which doesn't run at it's default speed. It's currently at FSB 800, CPU Host 200 and CPU 3000 MHz; but sometimes it runs at FSB 533, CPU Host 133 and CPU 2025 MHz. Sometimes it's even at FSB 75 and CPU 1128 MHz. When I configure the default settings in Easy Tune then my computer doesn't work. Sometimes I need to clear the CMOS so I can set the default settings in the BIOS, but that doesn't always help. I've updated the BIOS, what else can I do to fix this problem?

    Read the article

  • Computer Locks Up Completely When Resuming From Standby

    - by kcoppock
    Okay, so I'm having a strange issue lately with my desktop, and off the top of my head I'm not sure what the problem is, so I'm hoping for some ideas on how to track down the cause. First, my PC: AMD Phenom 9600 Quad-Core 2.4 GHz 4 GB DDR2 160 GB boot HDD 1 TB & 120 GB secondary HDD Nvidia GeForce 8600 GTS Windows 7 Professional 64-bit I have my power settings as follows: Turn off the display: 10 minutes Turn off hard disk: 20 minutes Sleep after: Never After a while, I'll come back to use my computer again, wiggle the mouse, and the screen comes back on like normal, but the desktop is unresponsive. I can move the cursor, but nothing responds to clicks or keyboard entry. If I click a few times with the mouse, the computer eventually locks up completely and the mouse cursor stops moving as well. After I restart, everything works just fine. Is there a log you recommend checking or really any suggestions would be welcome at this point. Thanks!

    Read the article

  • RAID--0 " TWO " DRIVES SSD ONLY Should I use on-board / Software RAID OR a RAID Card / Control

    - by Wes
    I am looking at going with a TWO Drive Only SSD RAID-0 Configuration And was wondering if I would get better performance / Speed from the Use of a RAID Controller / Card Verses just using the Software RAID on my Mother Board. I have herd conflicting reports , Again I only Plan on Running " 2 " SSD Drives in RAID-0 Config I have No- problem spending the extra money for a good controller but only if I am going to benifit performance wise , Otherwise if there is no notable Gain I will just use the Software RAID that my HP-180-T came with Intel- 3.33 GHZ , 6-Core , 12-GB of DDR-3. I have a huge External drive for All Storage and am not concerned about Data loss just looking for pure speed. And if a Controller will benifit my performance Wht type of card would one suggest?

    Read the article

  • Ideal laptop specs for a Computer Science Masters student?

    - by Ayush
    I have a HP pavillion core 2 duo 2 GHz and 4 GB RAM, and it is painful to use this machine for any kind of coding. Eclipse (especially Juno) literally takes 5 minutes to load. And even after that, everything is lagy. Apart from school stuff, I also use my computer as a television. I watch Hulu, Netflix, YouTube etc in 720p, and this laptop gets hot as hell and the fans are loud enough to wake somebody up from deep sleep. I DON'T use my laptop for Gaming or Video/Photo Editing. I'm looking to buy a new laptop (in which most widely used IDEs would work smoothly and playing hi-def videos wouldn't be too much for the machine to handle) any suggestions (on hardware specs) would be greatly appreciated. Thanks

    Read the article

  • High load on a nagios server -- How many service checks for a nagios server is too many?

    - by Josh
    I have a nagios server running Ubuntu with a 2.0 GHz Intel Processor, a RAID10 array, and 400 MB of RAM. It monitors a total of 42 services across 8 hosts, most of which are checked using the check_http plugin even 5 minutes, some every minute. Recently the load on the nagios server has been above 4, often as high as 6. The server also runs cacti, gathering statistics every minute for 6 hosts. I wonder, how many services should hardware like this be able to handle? Is the load so high because I am pushing the limits of the hardware, or should this hardware be able to handle 42 service checks plus cacti? If the hardware is inadequate, should I look to add more RAM, more cores, or faster cores? What hardware / service checks are others running?

    Read the article

  • laptop suddenly became very slow

    - by Ieyasu Sawada
    I have a compaq laptop. And I've been using it 2 years now. Then this day, it suddenly became very slow. It almost took 5 minutes from turning on to the log on screen. I click my username and it took 3 minutes to show the desktop. I click on my computer then properties to see if it is still showing 2 Ghz for the Core 2 duo processor. And 2gb for the memory. It took 10 minutes for all the information to show up. And its still 2gb and 2Ghz. So I may conclude that this is not a problem in memory or cpu. Its still running perfectly last night. And I have not seen signs of it failing. Things I already tried: Rebooting Shutdown then turn on again So how do I determine what causes this problem? How do I fix it?

    Read the article

  • Why does Windows 7 x64 work faster than an x86 edition on my PC?

    - by Jasper
    Why does Windows 7 x64 work faster than an x86 edition on my PC even though I mostly use x86 things in it? What's wrong with me, and what am I missing? Majority of the things I use is x86 (e.g. DAWs, games, media players). A considerable amount of them, however, are x64 (although their x86 counterparts work just fine). I've tried using the same things on the same system but always ended up finding Windows 7 x64 working slightly faster than x86. I'm very observant. I even notice the tiniest window animations. System: Windows 7 Ultimate x64 CPU: Intel Core 2 Duo E7500 @ 2.93 GHz RAM: 2 GB x 2 = 4 GB DDR2 @ 332 MHz Motherboard: Intel D945GCNL Graphics: ATI Radeon HD 4350 @ 1 GB Dedicated Audio: M-Audio FastTrack Pro HDD: Samsung HD753LJ 733 GB & Samsung HD160JJ 156 GB As you can see, my system is old.

    Read the article

  • Apple Airport Extreme Wireless Card M8881 Connectivity Issue

    - by Carlosfocker
    I bought a Apple Airport Extreme Wireless Card M8881 with the antenna for my old Power Mac G5 1.6 Ghz. The computer is running OS X 10.4. The card works and I can connect to my dlink 802.11g wireless router using WPA2/AES encryption. The problem is that the connection has intermittent connectivity issues. When the issue occurs the signal bars for the connection drop to one or two bars and the performance of the connection suffers greatly. The computer isn't far from the wireless router. I have a laptop at the desk where the mac is and it does not have any issues. I'm not sure what it might be? Updated drivers? Firmware? Let me know if I forgot any important information.

    Read the article

  • MacBook repeatedly disconnects from Wi-Fi

    - by redwall_hp
    I have an early 2008-model MacBook (2.4 GHz). The Wi-Fi router I have at home is a Linksys WRT54GX2 that I have had for a few years. My MacBook has recently started disconnecting from the router every few minutes, which is rather annoying. I can reconnect again without having to restart the router or anything, as it seems that the MacBook is just dropping the connection. I have tried changing the channel on the router, and upgrading the laptop from Leopard to Snow Leopard made no difference either. I'm only about six feet from the Linksys device, so distance isn't an issue. This only happens with the Linksys router, while I can use the local library's open network without any issues. The problem also seemingly becomes more pronounced after midnight. What could the problem be? Edit: Here are the logs that Spiff requested: http://pastie.org/951761

    Read the article

  • Firefox (on windows) constantly consuming 10% CPU - is there an add-in to find the rogue tab?

    - by tbone
    I often have many Firefox windows open, each with many tabs. Now and then one of the tabs will be running a web page that for some reason consumes lots of resources. Right now, I have a tab somewhere that is constantly consuming 10% of the CPU...which would be fine as my computer can easily handle that (see specs below...all other apps are responsive), but it seems to slow Firefox down....everything, everywhere is extremely laggy in Firefox, I can see pauses while I type this. Is there: - a way I can isolate separate instances (or even tabs) in FF into a separate process, so one rogue tab doesn't bog down FF across the entire system? - maybe an add-in that can either identify tabs consuming lots of CPU, or maybe a way to "shut down" activity on tabs you haven't used in a while? Firefox 3.6.10 Windows 7 Ultimate 64 i7 920 @ 3.6 GHz 12 GB Ram

    Read the article

  • Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

    - by jindrichm
    I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

    Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >