Search Results

Search found 5313 results on 213 pages for 'steve care'.

Page 160/213 | < Previous Page | 156 157 158 159 160 161 162 163 164 165 166 167  | Next Page >

  • Force local IP traffic to an external interface

    - by calandoa
    I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to forward all the traffic sent to one of these local addresses through the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 should be not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. May be I could then do NAT forwarding of all traffic directed to fake 192.168.1.2 on eth1, rerouted to 192.168.1.1 internally? I am actually struggling with iptables, but it is too tough for me. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

    Read the article

  • Load balancing a Windows File Share using HA-Proxy

    - by NathanE
    After pulling my hair out over DFS I just had this weird and potentially dangerous idea come into my head whereby, just possibly, I might be able to use HA-Proxy to load balance a file share between servers. I've done some remedial packet traces and it does appear that TCP port 445 is the only thing involved in using Windows file sharing. I've always thought for many years that UDP 139, 135 etc were also involved in at least establishing the connection - but apparently not! So I setup a basic test: listen SMBTest *:445 mode tcp server Smb1 172.16.61.201:445 server Smb2 172.16.61.202:445 And you'll never guess what... it works??? (!) Now obviously there is the whole concern about synchronisation between the file servers (of course). That could easily be taken care of with a little bit of Robocopy script. And considering I only need a HA read-only file share there wouldn't be any issues with regard to file locking etc. Can anyone tell me if what I'm playing with here is fire? I really didn't think it would work at all and now I'm a little shocked. What would be the downsides? Could this be relied upon for a production environment?

    Read the article

  • Advanced Linux file permission question (ownership change during write operation)

    - by Kent
    By default the umask is 0022: usera@cmp$ touch somefile; ls -l total 0 -rw-r--r-- 1 usera usera 0 2009-09-22 22:30 somefile The directory /home/shared/ is meant for shared files and should be owned by root and the shared group. Files created here by usern (any user) are automatically owned by the shared group. There is a cron-job taking care of changing owning user and owning group (of any moved files) once per day: usera@cmp$ cat /etc/cron.daily/sharedscript #!/bin/bash chown -R root:shared /home/shared/ chmod -R 770 /home/shared/ I was writing a really large file to the shared directory. It had me (usera) as owning user and the shared group as group owner. During the write operation the cron job was run, and I still had no problem completing the write process. You see. I thought this would happen: I am writing the file. The file permissions and ownership data for the file looks like this: -rw-r--r-- usera shared The cron job kicks in! The chown line is processed and now the file is owned by the root user and the shared group. As the owning group only has read access to the file I get a file write error! Boom! End of story. Why did the operation succeed? A link to some kind of reference documentation to back up the reason would be very welcome (as I could use it to study more details).

    Read the article

  • Enabling hardware acceleration and Xinerama for multi-monitor/multi-GPU in Linux

    - by mynameiscoffey
    My current setup is three monitors connected as follows (monitors listed from left to right): GPU0 (nVidia GTX 280): - Dell 2405FPW (1920x1200) - Dell U2410 (1920x1200) GPU1 (nVidia 210): - Dell 2405FPW (1920x1200) Works like a charm in Windows 7, not so much in Linux. I seem to only have three real options: Run all three monitors as a seperate X screen, I get hardware acceleration but as they are all independent X sessions I cannot move windows between them and can only have firefox open on one at any given time. Run the two on GPU0 in TwinView mode and have GPU1 as a seperate X screen. Same limitation as 1 but at least two monitors work together ok. I did have an issue where occasionally Linux saw both monitors on GPU0 as a single large monitor however. Enable Xinerama and have everything work as I want it to but hardware acceleration is gone and the display is Windows 95 style choppy. My ideal solution would be to have all screens working as they do under Xinerama without the limitation of having hardware acceleration disabled. I don't even care if that means rendering all three on GPU0 and somehow farming out the display of the third monitor to GPU1, whatever works. My question is this: is there any way to accomplish this? I don't feel like my use case is so out there that there shouldn't be at least some form of support (beyond the three limited options presented above), or is my best option going to be to just suck it up and pick up a better card to replace both that can handle three outputs by itself?

    Read the article

  • Reducing video mode switching during Linux boot

    - by Zack
    When I boot up my desktop computer, which only has Linux on it, the video mode and/or console font gets switched four times: When GRUB starts, it switches from 80x25 text to a graphical mode so it can draw a pretty background behind its menu; GRUB then goes back to 80x25 text after I pick something from the menu; When the KMS driver for my video card loads, it switches to a much higher-resolution text mode (I don't know if this is a hardware text mode or not); Finally X starts and it goes graphics and stays that way. I think this last switch does not change the resolution of the video mode, only the graphicalness. I'd like to get rid of as many of these mode switches as possible. Ideally, when GRUB takes over from the BIOS it would go directly to the same high-resolution text mode that the KMS driver selects, and the display would stay in that mode till X starts and brings up graphics. I am under the impression that this is possible by mucking with the kernel command line and/or the GRUB console module load parameters, but I don't know the details. GRUB 1.98+20100706, kernel 2.6.32.15 using Nouveau video drivers. Distro is Debian unstable. Please no answers that involve recompiling anything or cobbling together bleeding-edge kernel/driver combinations, I don't care enough about this to go to that much trouble. EDIT: Tobu suggests setting GRUB_GFXMODE to the full pixel resolution of the monitor, and GRUB_GFXPAYLOAD_LINUX=keep to avoid the mode switch after the menu goes away. This does part of what I want, but winds up being worse overall. There's no mode switch after the menu, but there's still a painfully-slow screen repaint (I should probably just give up on GRUB's gfxmode, it's waaaay too slow at 1920x1200). More seriously, there's now a double mode switch when nouveaufb loads, along with fun-looking error messages in dmesg [ 5.923798] [drm] nouveau 0000:02:00.0: allocated 1920x1200 fb: 0x40250000, bo ffff8801ba5f4600 [ 5.923802] fb: conflicting fb hw usage nouveaufb vs EFI VGA - removing generic driver [ 5.923821] [drm] nouveau 0000:02:00.0: PFIFO_INTR 0x00000010 - Ch 1 ("PFIFO_INTR" message repeats 400+ times) [ 5.925609] Console: switching to colour dummy device 80x25 [ 5.925802] Console: switching to colour frame buffer device 240x75

    Read the article

  • Update Grub on Squeeze - Kernel downgrade due VMware Server

    - by vodoo_boot
    Hi! I happen to run into various problems regarding grub and kernels. I don't really care about the kernel internas. All I want is VMware server in that dedicated root-server. 1.) What is a bzImage vs. vmlinuz? kaze:~# ls /boot/ System.map-2.6.32-5-amd64 bzImage-2.6.33.2 config-2.6.33.2 initrd.img-2.6.32-5-amd64 System.map-2.6.33.2 bzImage-2.6.35.6 config-2.6.35.6 vmlinuz-2.6.32-5-amd64 System.map-2.6.35.6 config-2.6.32-5-amd64 grub I updated my menu.lst (grub2): timeout 5 default 0 fallback 1 title 2.6.32.5 kernel (hd0,1)/boot/vmlinuz-2.6.32-5-amd64 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.35.6 kernel (hd0,1)/boot//bzImage-2.6.35.6 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.32.3 kernel (hd0,1)/boot//bzImage-2.6.33.2 root=/dev/sda2 panic=60 noapic acpi=off That doesn't do well... I think the vmlinuz file is missing initrd or so. Dunno. In fact I don't give too much about kernel boot voodoo as long as it works. update-grub(2) does not work. Does anybody know what magical trick there is to get the 2.6.32-5 booting? 2.) I thought t follow the Deban wiki.. I cannot get header-files for the installed 35.6 or 33.2 kernel in the repositories. I cannot build foreign headers because they will not match the running kernel. So how does one deal with that situtation? I'd prefer not to have to downgrade the kernel. Thanks for any answers!

    Read the article

  • How to find the real IP to which IPVS is routing a virtual IP

    - by Wayne Conrad
    I'm trying to find a problem server hiding behind a virtual IP (using LVS/ipvs). I've got a test program that sends requests to the virtual IP until it gets the bad response, but how can I tell to which real IP a request to the virtual IP got routed? On the box doing the virtual IP magic, here's the virtual IP configuration (for the service I care about): IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn ... TCP 10.1.0.254:5025 nq -> 10.1.0.5:5025 Route 1 0 1 -> 10.1.0.6:5025 Route 1 0 5 -> 10.1.0.7:5025 Route 1 0 2 -> 10.1.0.9:5025 Local 1 0 3 -> 10.1.0.11:5025 Route 1 0 3 ... My client program is sending TCP requests to 10.1.0.254:5025, usually getting a good response but sometimes a bad response. With this few servers, I could send my request to each server in turn until I discover the culprit, but I wonder if that technique will scale as we add servers. What means exist for me to find out where requests got routed? Kernel: Linux 2.6.32 OS: Debian testing (whatever that's called these days). ipvsadm is version 1.25, compiled with ipvs v1.2.1

    Read the article

  • Replacing all disks in a non-OS RAID 5 volume

    - by molecule
    Hi all, We currently have a server with 8 x HDD slots. It is a HP DL380G5 with a P400 controller. 2 x HDD are in a RAID 1+0 config and this hosts the OS. 6 x HDD are in a RAID 5 config and holds an Oracle DB. Basically the RAID 5 volume is running out of space and we would like to swap all 6 with higher capacity disks. Excuse my ignorance as I am pretty new to this... I believe we will need to backup the data, delete the RAID volume, insert the new disks, recreate the volume, and restore the data. 2 questions: Do we need to worry about the OS partition or is it completely independent so we can simply take out the 6 and insert 6 new disks and get the controller to recognize the 6 new disks and form a new RAID 5 volume? We should not need to reinstall OS or Oracle correct? Since we are going to restore the data on the volume from another source (our vendor will take care of this) but we would like to keep the existing data on the 6 disks just in case we run into issues and want to fall back, is this possible? Thanks in advance.

    Read the article

  • Looking for an application to record audio and video on a linux "embedded" device

    - by Luke404
    I am working with a linux x86 device with limited CPU resources (as a prototype we just use a pentium-m netbook). We'd like to record video from one V4L2 device (we'll probably end up using just USB Video Class devices like all modern webcams) and one audio stream from an ALSA source. The thing will not have screen and keyboard, and obviously no X11 environment. Goals are: do as little work as possible to cope with little cpu resources - for example I'd like to record video in the native MJPEG I get out of the UVC devices encoding audio to MPEG3 Layer-2 (aka mp2) is ok since it let us save a lot of space (compared to raw pcm samples) and does use little cpu power I don't mind loosing some video frames here and there (UVC devices do that) as long as I can get audio and video streams syncronized not require user input to start the thing (a python script takes care of initialization, startup, shutdown, etc...) be able to open the resulting files for postprocessing without too much effort (ie, if mplayer or vlc can play it, it's fine) So far the only app I found that could be started from command line and record V4L2 video + ALSA audio is mencoder but I'm having some difficulties with it. It should be able to do that but I cannot record audio and video together - just one of the two. And if I use two different processes to record to two different files I have no means to get them in sync (audio is more or less always correct, but video framerate will vary over time and it seems to lack timestamps to correctly play it back to the correct time). Long story short, how do you record an unconverted MJPEG stream (from an UVC device) and an audio stream (from an ALSA device, possibly encoding to any standard format) using a command line tool, to a single file (MPEG or any other container), keeping audio and video in sync?

    Read the article

  • My New Dell Workstation T-7500 gives electric shock

    - by Dan
    Just bought Dell T-7500 Workstation. When installation technician came to Install the workstation, he got an electric shock when he touched the Start Button. He also got shock when he touched Front Panel. No shock when touching rest of the Chassis. He called Dell Support & tried to troubleshoot by taking out various wires etc but did not help. I touched the same places & I also got shock. We checked everything possible including connecting to various outlets but it didn't solve the problem. Installation subcontractor said that they are not supposed to troubleshoot anything on new system, just install it & they made notes & left. I called my sales guy & it was weekend so he said he will take care of it on Monday. Here are my concerns : (1) Why does that happen ? Although it is a mild shock & it won't kill you but might damage other parts of workstation ? (2) Is this common for workstations ? (3) What should I do ? Of course Dell will try to troubleshoot again but should I let them do that OR ask for a New System ? (4) Wheat would happen if I continue using it till the new system arrives ? Thank You.

    Read the article

  • Visual Studio 2010 Beta 2, built-in font smoothing

    - by L. Shaydariv
    I've just installed Visual Studio 2010 Beta 2 onto my Windows XP to evaluate it and check whether it meets my preferences the way it did before. Okay, I've temporary defeated an urgent bug with a strange workaround (I could not open any file from the Solution Explorer), and it left bad memories to me. But however, it's okay. The first thing I've seen just opening the code editor was ClearType font rendering. Wow, so unexpectedly. I must note that I do not use standard Windows rendering techniques, but I still prefer GDI++, a font renderer developed by Japanese developers. (GDI++ allows to render the fonts in Mac/Win-Safari style over entire Windows.) Personally for me, GDI++ reaches the great font-rendering results allowing me to use the Dejavu Sans Mono font with really nice smoothing in Visual Studio 2008 (VS 2005 too, though VS 2005 crashes in this case). But GDI++ cannot affect Visual Studio 2010 Beta 2 text editor - it uses ClearType (right?), and it does not care about the system font smoothing settings. It could be an editor based on WPF, right? So as far as I can see, I can't use GDI++ anymore because it uses Windows GDI(+) but no WPF? So I've got several questions: Is it possible to disable VS 2010 b2 built-in ClearType or override it with another font smoother? Is it possible to install a Safari-like font renderer for Visual Studio 2010 [betas]? Thanks a lot.

    Read the article

  • Libraries merged folder views

    - by Stigma
    So I pretty much love the Windows 7 Libraries feature, and saw one use for them that I thought would be perfect, but I can't seem to manage it. Basically, a merged view of different folder structures. Suppose I make a new generic library and add three locations to it: C:\Test\, D:\Test\ and D:\temp\Test\. Now, these may look somewhat okay as long as there are no duplicates in these folders. (It wants to group them based on the included directory, which one can work around by looking on google - I don't have the precise trick on hand I am afraid.) But when you get collisions and, say, two of those directories have a Sub directory in them, stuff becomes unusable (assuming Arrange by: Folder view). You'll have multiple folders listed named Sub, which is pretty useless when looking for data. I want folders to get 'merged', which ought to be possible somehow since it can create these merged views based on artist, album etc in other views. So all subdirectories that are double (and recursively checking for doubles inside those, etc) ought to be merged for as far the View is concerned. If files have a collision, I don't really care what happens - hide one, show both, filter out duplicates, whatever. (Although an option would be nice...) Anyhow, is there anyone who knows how to get such a 'merged folder structure' functionality for Libraries? It would be really useful for me.

    Read the article

  • How would I force Debian to use the physical sector size on a hard disk?

    - by Confused User
    I just purchased a few new 3TB WD drives. These have physical 4k sectors, but there is some sort of layer which is providing 512B logical sectors (see the partition table below). In order to attempt to get some more speed out of my hard drives, I would like to get rid of this logical layer and actually use the physical 4k sectors. However, I can't figure out how to do this (or even if it's possible) from the man pages of fdisk and parted, or from searching Google. Does anybody know how this could be done? As to why this is relevant, this page demonstrates that meerly aligning the sectors properly can already make up to a 25% speed difference for reads, and more than 2500% for writes in some cases! Getting rid of the logical sectors in favor of the physicals ones should improve speeds even more. Thanks! $ parted /dev/sdc GNU Parted 2.3 Using /dev/sdc Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) print Model: ATA WDC WD30EZRX-00M (scsi) Disk /dev/sdc: 3001GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 3001GB 3001GB zfs 9 3001GB 3001GB 8389kB P.S. I don't care about the data on the drives, I was just playing with different file systems. Also, this is my first time posting here, so please let me know if my posts should be formatted differently, etc.

    Read the article

  • How private is the Opera Turbo feature of Opera?

    - by Marcus V
    If I'm using Opera with the Opera Turbo feature turned on (always, not set to "automaticly"). Can anyone see what sites I'm visiting (except Opera of course ...)? Opera Turbo uses a proxy server, so it should be that way, but as a not very technical person I'm not sure. Why do I want this? Well: nowadays, at least in my country, more and more (legal) open Wi-Fi connections are available. In those environments I like to have more privacy protections. I don't mind if they can see my IP address, but I just want to hide as much as I can of what I am doing. BTW: I don't care that they can see the data transferred; it doesn't have to be that secret. I only want to hide the requested Internet site links. BTW: I know that Opera Turbo only works with non-secure websites (HTTP), but that's fine for me. I only want it to work with these sites. BTW: I'm not need this for illegal purposes; I only want this for privacy reasons.

    Read the article

  • Ubuntu Wubi "drive" failure; mount drive in XP?

    - by 618034
    Hi there, I installed the Wubi distribution of Ubuntu on a separate partition (which is silly, since why do I care if Windows can still manage the partition?) a few months back; it was pretty awesome, until Linux hosed. At this point, I can get Ubuntu to boot if I try really hard through grub, but once it does start, the screen is hosed, so no dice. At this point, I'd like to wipe it all and start over, but I need to get some stuff off the "disk". The Wubi install makes this difficult, since the "disk" is a flat file on an NTFS partition. I've done just about everything I can think of — I renamed the virtual disk .iso, mounted it with VirtualCloneDrive, then used whatever magic EXT3 (EXT4?) readers I could dig up on the Internet to parse the mount — but nothing's working. Can you offer any suggestions? The "disk" is currently in D:\ubuntu\disks\root.iso. Many thanks! (I may be high-latency at the moment, apologies if I don't address follow-ups quickly)

    Read the article

  • How to replace the domain name in a Wordpress database?

    - by Cristian
    I have a Wordpress database which was installed in a development environment... thus, all references to the site itself have a fixed IP address (say 192.168.16.2). Now, I have to migrate that database to a new Wordpress installation on a hosting. The problem is that the SQL dump contains a lot of references to the IP address, and I have to replace it with: my_domain.com. I could use sed or some other command to change the that from the command line, the problem is that there are a lot of configuration data which uses JSON. So what? Well, as you know, JSON arrays uses things like: s:4: to know how many chars an element has, and thus, if I just replace the IP with the domain name, the configuration files will get corrupted. I used an app for Windows some years ago that allows to change values in a database and takes care of the JSON arrays. Unfortunately, I forgot the name of the app... so the question is: do you know any app that allows me to do what I want?

    Read the article

  • Install a KVM guest with LVM partitioning on an LVM partitioned host using virt-install fails, volume group already exists

    - by Rilik84
    our setup consists of a ubuntu 10.04 kvm host server with LVM, on top of which we install the ubuntu 10.04 virtual machines via virt-install and preseed. Each VM has a dedicated logical volume which we pass to virt-install via the "--disk path=/dev/sysvg/vm-name" parameter. The virtual machines themselves are using LVM as well. Virt-install seems to have a few issues with this setup. Say we want to install two virtual machines in parallel. The first vm installs correctly while the second halts during the partitioning, complaining with this error: "volume group name already in use". I tried removing the logical volumes, recreated them, rebooted the kvm host to clear any leftovers but the issue perists. The preseed is telling the vms to create a volume group named "sysvg", which is the same name used by the volume group of the kvm host. Considering this I did another test: I got rid of the preseed part taking care of the partitioning/lvm creation and started the creation of two vms in parallel. If, when prompted, I instruct the vms' installer to do a guided partitioning of the disk with LVM, it will still fail giving this different error on both the vms: Physical Volume /dev/sda5 is already in volume group sysvg. As I wrote, sysvg is the volume group used by the KVM host. So I thought the name clashing was the issue. By removing the preseed part I skipped the volume group naming. I can't understand how the virtual machines would be aware of the presence of that volume group since they're supposed to be isolated from it, especially after I removed and recreated the logical volumes dedicated to them. That detail should not be exposed at all to them! Thanks for the help. I'm clueless.

    Read the article

  • Update BIOS on Sun Fire X4150 server

    - by Massimo
    I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

    Read the article

  • How to setup NTFS ACL with Acces Based Enumeration

    - by Patrick Pellegrino
    We're in the process of migrating from Novell Netware to Windows 2K8 R2 infrastructure (AD, File server, print server... etc) My question is about ACL. While Netware and Windows are totally different, I want to be sure my thnking is good before screwing everything up! There's a scenario : F: | +-- DATA <= Shared as DATA with Access based enumeration | +-- Folder 1 +-- Team 1's Folder +-- Team 2's Folder ... In that case, by default, rights are herited from the F: to the deepest folders. What we want : Administrators group have full control top - down. From DATA, ABE list only folders that users have access. (ex. : I'm in group Team 2, I see Team 2's Folder). From what I understand, at DATA I remove all NTFS ACL to be herited (ex. Users Group), be sure to keep Administrators Group and SYSTEM user. After that, grant Full control (or any right needed) on each folder to Groups or Users that have to have access. Does I'm wrong ? Anything I should take care of ? Any help to my understanding will be very appreciated. Regards.

    Read the article

  • How can I make Internet Explorer 6 render Web pages like Internet Explorer 11?

    - by gparyani
    Now, I know that this may seem like a bad question in that I can just upgrade to Internet Explorer 8, but I am sticking with IE6 in that IE8 removes valuable features, like the ability to save favorites offline and the fact that a file path turns into a Windows Explorer window and typing a Web address into Windows Explorer changes it into an IE window. I know that Internet Explorer 6 does a really bad job at rendering some pages. I know of the Google Chrome Frame extension that brings Chrome-style rendering into IE, but that will soon be discontinued. So, I tried another thing: I know that C:\Windows\System32\mshtml.dll contains the Trident rendering engine that is used by IE, so I tried something: I first backed up the original file by renaming it on Windows XP to mshtml-old.dll, then I tried to copy in the DLL from a computer running Windows 7 with Internet Explorer 10. I noticed that, after copying, the system had replaced the new DLL with the old one, but left the one I backed up intact. Is there any way I can get the system to not replace the DLL like that so that I can transfer in IE11's mshtml.dll into Windows XP and make IE6 render like IE11? I'm looking for an answer that describes how to tweak my system to make IE6 render like IE11 (or IE10), not one that tells me to upgrade IE or install another browser. I don't care how tedious the method is, just as long as it works.

    Read the article

  • Search inside of text files

    - by Matt
    So here is the situation. I currently run a mail server for my small non-profit company. My mail server (Merak Mail Server) keeps logs in .log files and mail as .tmp files. Essentially these are just text files that are kept on the server. Problem is that when I put text into the "Containing text" field on Windows Explorer, it always misses the files and tells me no results returned. Then when I search the files one by one (painful at best), I find the files I need. Do I not understand the search feature well enough, or maybe I have it indexing wrong. I really don't care what I need to use to search the files, even a third-party app is fine with me, I just want to type an email address into a box and search all of my log files or email files and find out which one I am looking for. It can be Windows Search or something else, as long as I can find a way to get the job done I will be happy. Pay solutions are fine as well. Thanks everyone in advance.

    Read the article

  • Is it a good idea to run Redmine using Webrick through Nginx?

    - by Rohit
    The task here is to get Redmine setup for a small (<20) team. There may be a few users who would access the setup as business clients. I am familiar with setting up PHP for Apache, and recently, Nginx. I am not familiar with Ruby, Ruby-On-Rails, etc. I prefer to use the OS's (Ubuntu Linux LTS) package manager to install the different components as it takes care of dependencies and updates. I have setup Nginx with PHP-FPM successfully and am struggling with Redmine. As suggested here, I got Redmine running on port 3000. # /etc/init/redmine.conf # Redmine description "Redmine" start on runlevel [2345] stop on runlevel [!2345] expect daemon exec ruby /usr/share/redmine/script/server webrick -e production -b 0.0.0.0 -d And using the Nginx config on this page, I used Nginx to proxy requests to Webrick. server { listen 80; server_name myredmine.example.com; location / { proxy_pass http://127.0.0.1:3000; } } This works well locally. I wanted some opinions before trying this out on the live box (a 256 MB VPS). Further, should I use something like monit to monitor webrick for failure?

    Read the article

  • Building a Web proxy to get around same-origin restrictions for collaborative Webapp based on a MEAN stack

    - by Lew Cohen
    Can anyone point to books, articles, blogs, or even applications - open-source or proprietary - that detail building a Web proxy? This specific proxy will exist to get around the same-origin restrictions that prevent, for instance, loading a given Website into an <iframe> in a Webapp. This Webapp is a collaborative application in which a group of users log in to the app's Website and can then load different Websites into this app's <iframe> and do various collaborative things (e.g., several users simultaneously browsing a Website, in synch). The Webapp itself is built on a MEAN stack (MongoDB, Express, AngularJS, and Node.js). The purpose of this proxy is not to do anonymous browsing or to bypass censorship. Information on how to build such a vehicle seems not to be readily available from my research. I've come across Glype but am not sure whether this is a feasible solution. I don't want to reinvent the wheel, so if a product is available for purchase, great. Else, we'd need to build one. The one that seems to be close is http://www.corsproxy.com. In effect, we'd like to re-create this since it evidently does what's needed. I don't care what server-side technology is used. Our app is MEAN-based, if that has any bearing. Also, the proxy has to obviously honor basic security considerations (user cookies, etc.) and eventually be scalable. So, anyone know of any sources that would detail how to build one of these? Is it even worth building if something already exists? If so, what would be a good candidate? Any other issues that should be considered with this proxy/application? Thanks a lot!

    Read the article

  • Affordable combined Ruby/Rails/Redmine + Subversion hosting?

    - by Pekka
    I'm a self employed web developer and after nine years of hard work, I'm looking to become a bit more "vagrant" starting next year, do some much-needed traveling and a bit and work off and on, making use of one of the greatest advantages of a programming job: The ability to work virtually from everywhere. For that, I am looking for a reliable hosting company I can entrust my code to in the form of a number of Subversion repositories, and an installation of the Redmine project management tool. As my financial situation may vary during traveling, I am looking for something I can pay up front for a year or two, and is obviously not too pricey. I don't care where the company is located, as long as it's trustworthy and solid, meaning it's not likely to go out of business next month. Does anybody know good recommendations? Preferably from own, personal, good experience. I have looked at CVSDude / Codesion and while they are certainly great, they don't offer Redmine of course, and seem to be aiming toward bigger organizations mainly. What I would need: 2-5 Gigs of space minimum, freely distributable between SVN, and Redmine attachments Unlimited number of Subversion projects Access control (team members / checkout-only accounts / etc.) I don't mind configuring the svn settings on file basis myself I need the possibility to map a custom domain to the package that is hosted elsewhere Frequent backups and access to those backups through FTP or other means I have been running my own virtual server for this until now, but I don't want the hassle, especially on the security side, while I may not always have the internet connection to fix problems that may come up.

    Read the article

  • Fixed Resource Monitor Graph Scale in Windows Server 2008 R2

    - by Clever Human
    In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums?

    Read the article

< Previous Page | 156 157 158 159 160 161 162 163 164 165 166 167  | Next Page >