Search Results

Search found 20684 results on 828 pages for 'ad hoc network'.

Page 161/828 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

  • Best way to troubleshoot intermittent network outages?

    - by Ben Scheirman
    We have a Comcast 50/10 line into our office. We keep seeing very short but sometimes frequent drops in our internet service. It's enough to kick you off of skype and stop any websites from loading, which is obviously affecting our productivity. We've tried 4 different routers, we've tried moving everyone off of wireless and onto wired via a switch and so far nothing has helped. Right now we're on a Cisco SB WRP400-G1 router. Attached to the router is a 16 port switch going to the ports in all of the offices. We've moved to OpenDNS in the case that it was the comcast DNS servers going down. Today we tried putting the modem, router, and switch on a UPS to make sure it wasn't power fluctuations that was causing it. Every time we call Comcast, by the time they are here the internet is working fine. I'd like to somehow prove that the problem is with Comcast, so if that means plugging in a machine directly into their router and collecting data all day, I'm up for that. I just want to hear ideas on what tools to run and how to collect this data. I could just continuously ping google.com all day long but I'm not sure how valuable that data would be. Thoughts?

    Read the article

  • Run WMIC command across network

    - by C-dizzle
    Instead of typing this in a command prompt one at a time: wmic /node:ipaddress /user:administrator /password:mypassword bios get serialnumber How can I run that against one entire subnet and output to a text document? Since I do this every couple months to verify our inventory of computers, I would assume there would be a much of easier way I could put this in a batch script instead of doing it manually.

    Read the article

  • OpenVPN bridge network from routed clients

    - by gphilip
    I have the following setup: subnet 1 - 10.0.1.0/24 with a machine used as NAT and also running an OpenVPN client subnet 2 - 192.168.1/24 with an OpenVPN server (the server in subnet 1 connect here) subnet 3 - 10.0.2.0/24 that uses the NAT machine (subnet 1) to access the internet, so all non-local traffic is routed there to the eth0 interface The OpenVPN client creates the tun0 interface and appropriate routing so that I can access machines from 192.168.1/24 [root@ip-10-0-1-208 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... Connected to 192.168.1.186. Escape character is '^]'. [root@ip-10-0-1-208 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.1 10.8.0.5 255.255.255.255 UGH 0 0 0 tun0 10.8.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 169.254.169.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.0.0 10.8.0.5 255.255.0.0 UG 0 0 0 tun0 However, when I try the same from subnet 3, it can't reach that machine. [root@ip-10-0-2-61 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... I suspect that it's because subnet 3 is routed to eth0 on the NAT machine in subnet 1 and it cannot jump to tun0. What's the easiest way to resolve it? I don't want to use iptables. I can't change the routing from machines in subnet 1 because it's done in AWS and so it works only with specific interfaces. Also, the NAT machine gets its IP with DHCP and so bridging is a bit complicated. IP forwarding is set on the NAT machine [root@ip-10-0-1-208 ~]# cat /proc/sys/net/ipv4/ip_forward 1 Thank you!

    Read the article

  • My laptop can connect to every wireless network except fios

    - by going crazy
    I have always been able to connect to every wireless router secured or unsecured wep or wpa. I had Fios installed and could not connect. Verizon suggested it was my computer and gave me an outside wirless drive to use, it worked. I got rid of fios and went back to comcast and threw out the drive, but now 2 years later, I am sitting at my friends house haveing the same problem. My tech savy friend told me it is a firewall setting or something in my antivirus software, but I disabled them both and still nothing works........Funny it is only FIOS

    Read the article

  • Network-Backup-Software with file versioning and web-interface

    - by dlang
    Dear All! I would like to backup our business-data to a remote backup-server. We would like to set-up our own backup-server running on any operating system (windows appreciated) which comes with a web-interface, that enables to restore individual versions of one file. Because budget is limited, an open-source software or at least a cheap software is a must! Unfortunately I couldn't find even a single software, which fulfills the requirements of file versioning and web-interface for single file-restore. Do any of you have already set-up such a system? Best regards, Daniel Lang

    Read the article

  • Accessing Network Printers from a Citrix Session:

    - by Harry
    We have an application that uses Active Reports documents. You pass a document the UNC of the printer and away it goes. We have a group that runs this application within a Citrix session and the truly networked printers function perfectly but shared printers that work well outside of Citrix become unreachable. Printers do not need to be defined on the machine running the report for the system to work. There is something in the way Critrix passes the information to the destination UNC that I don’t understand.

    Read the article

  • Configuring Wireless Network

    - by Vinod K
    I have vyataa router on VMware with 2 interfaces eth0 and eth1 eth0 is facing the internet eth0 is in Nat mode with dhcp on eth1 is in bridged mode with my ethernet with ip 10.0.2.34/24 The ethernet card is at ip 10.0.2.95/24 i have defined the nat rule. Hence internet is available at eth1 too. Now i am connecting a wireless router at "eth1" iball router, I have connected the router using a cable to the ethernet interface of my laptop. I have configured the WAN connection type as "Static IP" and given "10.0.2.34/24" All the clients that connect using wireless router cannot connect to the internet though. Could anyone provide me a solution for this.. Thank You!!

    Read the article

  • Sharing soundcard to network.

    - by zerkms
    Let's suppose I have a laptop (L) and desktop PC (D), both with Windows 7 onboard. It is SB X-Fi extreme soundcard with rather good 5.1 home theater connected. But it is not comfortable to watch video sitting on the sofa from my desktop (sofa is in the center of the room and D is in the corner), even though it is 23" monitor. So I'm watching everything from the laptop. So the question - is it possible somehow to "share" soundcard from D to L, so I will watch the video from notebook and listen the sound from the 5.1? L and D are connected via wi-fi (fast enough).

    Read the article

  • Git clone/pull across local network

    - by Tom Sarduy
    I'm trying to clone/pull a repository in another PC using Ubuntu Quantal. I have done this on Windows before but I don't know what is the problem on ubuntu. I tried these: git clone file:////pc-name/repo/repository.git git clone file:////192.168.100.18/repo/repository.git git clone file:////user:pass@pc-name/repo/repository.git git clone smb://c-pc/repo/repository.git git clone //192.168.100.18/repo/repository.git Always I got: Cloning into 'intranet'... fatal: '//c-pc/repo/repository.git' does not appear to be a git repository fatal: The remote end hung up unexpectedly or fatal: repository '//192.168.100.18/repo/repository.git' does not exist More: The other PC has username and password Is not networking issue, I can access and ping it. I just installed git doing apt-get install git (dependencies installed) I'm running git from the terminal (I'm not using git-shell) What is causing this and how to fix this? Any help would be great! UPDATE I have cloned the repo on Windows using git clone //192.168.100.18/repo/intranet.git without problems. So, the repo is accessible and exist! Maybe the problem is due user credentials?

    Read the article

  • Windows network takes long time to access

    - by IrfanRaza
    Hello friends, I have 4 Winodws XP systems connected in a domain with Windows 2003 server. Domain name is "SoftGenIndia". We are using Star topology. I have checked all the cables and connections, all are OK. What happening is that when i try to open the computer on domain it takes long time to show the shares (around 2-3 mins). Is there anything i am missing? Can anybody provide solution on this. Thanks for sharing your valuable time. Regards Mohammad Irfan http://softwaregenius.net

    Read the article

  • Neural Networks or Human-computer interaction

    - by Shahin
    I will be entering my third year of university in my next academic year, once I've finished my placement year as a web developer, and I would like to hear some opinions on the two modules in the Title. I'm interested in both, however I want to pick one that will be relevant to my career and that I can apply to systems I develop. I'm doing an Internet Computing degree, it covers web development, networking, database work and programming. Though I have had myself set on becoming a web developer I'm not so sure about that any more so am trying not to limit myself to that area of development. I know HCI would help me as a web developer, but do you think it's worth it? Do you think Neural Network knowledge could help me realistically in a system I write in the future? Thanks. EDIT: Hi guys, I thought it would be useful to follow-up with what I decided to do and how it's worked out. I picked Artificial Neural Networks over HCI, and I've really enjoyed it. Having a peek into cognitive science and machine learning has ignited my interest for the subject area, and I will be hoping to take on a postgraduate project a few years from now when I can afford it. I have got a job which I am starting after my final exams (which are in a few days) and I was indeed asked if I had done a module in HCI or similar. It didn't seem to matter, as it isn't a front-end developer position! I would recommend taking the module if you have it as an option, as well as any module consisting of biological computation, it will open up more doors should you want to go onto postgraduate research in the future. Thanks again, Shahin

    Read the article

  • What router settings to use for wireless home network

    - by Question Overflow
    While looking at the setting of my wireless router, I am bewildered by the array of options available. Despite searching on Wikipedia to try to understand the various acronyms, I am still clueless to decide what is the best setting to use although the default works fine. Rather than calling the internet service provider (ISP) to ask them the correct settings, I hope to learn more about the differences between some of the options listed below, so that I would be able to make a more informed decision from now onwards: PPPoE vs PPPoA LLC vs VC-Mux Bridge vs Routed In addition, I would also like to know the significance of the following MTU VPI VCI And whether or when I should manually specify DNS?

    Read the article

  • Windows 7 VPN wont allow FTP, route FTP traffic through local network

    - by Rolf Herbert
    I use a VPN on my windows 7 PC for privacy and currently route all my traffic through the VPN. This arrangement is fine and its plenty fast. Unfortunately the VPN does not allow any FTP traffic so when I am updating websites I have to disconnect the VPN and work through my local connection. This is annoying and cumbersome. I have read a little about split tunnelling but this is not quite what I need, and it often talks about 'internet' traffic which is not specific to certain IPs or ports. Is it possible to route traffic on certain ports through the local connection, or is it possible to route traffic on certain IPs through the local connection using stuff built into windows 7..? Thanks

    Read the article

  • IIS not listening over external network, all other traffic working

    - by Beuy
    Hello there, I have a very odd situation, I have a server (let's call it X) running 2008 R2 with two NIC's in it, one is connected to the work domain and has a subnet of 192.168.10.0/24 the other is connected to a ADSL connection and has a subnet of 192.168.1.0/24. The server has IIS installed. On the ADSL connection I have setup a dynamic dns and port forwarding to allow external HTTP, HTTPS, FTP and RDP connections. FTP and RDP are working fine however neither HTTP or HTTPS are working at all. I can browse the websites by going to localhost on the machine, the HTTP and HTTPS ports appear as "Filtered" when I try to scan them using PortQueryUI and browsers respond with a "Server took too long to load or was not responding" error. This was working fine just a few days ago, Windows firewall is disabled I don't have any software firewall on it. And I'm really lost. Any help would be great.

    Read the article

  • file saving problem into the network

    - by santosh
    i have a problem when i save the office file in to the server through the client its show you it is read only file & also shows the disk is full or write protected what have to for this problem please give me the seggstion if have

    Read the article

  • Best network tuning variables for a Linux proxy

    - by smarthall
    What are the best settings to tune so that Linux can handle a very large amount of TCP connections such as would be seen by a proxy server or a webserver? I'm using Centos6 and squid and am seeing a large amount of TIME_WAIT connections backing up until finally the machine stops responding. The machine isn't loaded at the time, and is having trouble making ingoing and outgoing connections. I've had several suggestions of tuning /proc/sys/net/ipv4/tcp_tw_reuse and /proc/sys/net/ipv4/tcp_tw_reuse but they mention bad interactions with load balancers and NAT both of which are used in my situation.

    Read the article

  • What makes people think that NNs have more computational power than existing models?

    - by Bubba88
    I've read in Wikipedia that neural-network functions defined on a field of arbitrary real/rational numbers (along with algorithmic schemas, and the speculative `transrecursive' models) have more computational power than the computers we use today. Of course it was a page of russian wikipedia (ru.wikipedia.org) and that may be not properly proven, but that's not the only source of such.. rumors Now, the thing that I really do not understand is: How can a string-rewriting machine (NNs are exactly string-rewriting machines just as Turing machines are; only programming language is different) be more powerful than a universally capable U-machine? Yes, the descriptive instrument is really different, but the fact is that any function of such class can be (easily or not) turned to be a legal Turing-machine. Am I wrong? Do I miss something important? What is the cause of people saying that? I do know that the fenomenum of undecidability is widely accepted today (though not consistently proven according to what I've read), but I do not really see a smallest chance of NNs being able to solve that particular problem. Add-in: Not consistently proven according to what I've read - I meant that you might want to take a look at A. Zenkin's (russian mathematician) papers after mid-90-s where he persuasively postulates the wrongness of G. Cantor's concepts, including transfinite sets, uncountable sets, diagonalization method (method used in the proof of undecidability by Turing) and maybe others. Even Goedel's incompletness theorems were proven in right way in only 21-st century.. That's all just to plug Zenkin's work to the post cause I don't know how widespread that knowledge is in CS community so forgive me if that did look stupid. Thank you!

    Read the article

  • Enter network credentials as part of batch script

    - by Michael
    WinXP: I have several system services that are needed to run some machinery in my lab. The machine these services are running uses a lab login that has administrator rights. Our IS department, unfortunately, has it set up where at some point during the night the login "loses" the privilege level to start/stop these services. The account stays logged in, but the software controlling my hardware becomes unresponsive. In order to get things back up and running, I have to stop the system services and restart them. Because of the security settings, however, I have to re-enter the user password to start the service (even though the user was never logged out). That, I get the "This service cannot be started due to a logon failure" and I have to enter the password. What would be ideal is to have a batch script run before anyone gets into work that stops all of the necessary services, enters the user credentials when prompted, and then restarts them so that everything is ready for first shift to run. I assumed that using the Task Scheduler in Windows would work as it allows you to run batch files with a user's name and password, but this didn't seem to do the trick. With this setup I would arrive to find that all the services are stopped but not started again. (Presumably because the authentication failed.) The batch file is about as simple as it gets, all I have is: net stop "Service1" net stop "Serivce2" etc., then restart in reverse order based on dependency: net start "Service2" net start "Serivce1" What would it take to accomplish what I'm trying to do and restart the services?

    Read the article

  • Wake for Network Access Apache servr in OS X 10.8, followup

    - by Gary
    Sorry, I can't seem to post this response within the same thread. Thank you both (Zoredache and Gordon) for your answer. But the fix seems temporary. I entered the command you suggested, and it seemed to work: ...smith$ Registering Service ApacheNoDoz._http._tcp.local port 80 DATE: ---Fri 14 Sep 2012--- 12:04:15.813 ...STARTING... 12:04:16.566 Got a reply for service ApacheNoDoz._http._tcp.local.: Name now registered and active So, I checked for it on my G5: Browsing for _http._tcp Timestamp.....A/R Flags if Domain......Service Type...Instance Name (lots of Bonjour printers omitted)... 12:07:38.370..Add.....2..4 local.......... _http._tcp.........ApacheNoDoz 12:07:45.921..Rmv.....0..4 local..........._http._tcp.........ApacheNoDoz So, it was running at 12:07:38, at which time the host was asleep. But, shortly after, the activity seems to have been removed. I don't know why. Does this mean that I can never let the cpu sleep, or is there something else I have to set? Thanks, again.

    Read the article

  • Keeping sync in multiplayer RTS game that uses floating point arithmetic

    - by Calmarius
    I'm writing a 2D space RTS game in C#. Single player works. Now I want to add some multiplayer functionality. I googled for it and it seems there is only one way to have thousands of units continuously moving without a powerful net connection: send only the commands through the network while running the same simulation at every player. And now there is a problem the entire engine uses doubles everywhere. And floating point calculations are depends heavily on compiler optimalizations and cpu architecture so it is very hard to keep things syncronized. And it is not grid based at all, and have a simple phisics engine to move the space-ships (space ships have impulse and angular-momentum...). So recoding the entire stuff to use fixed point would be quite cumbersome (but probably the only solution). So I have 2 options so far: Say bye to the current code and restart from scratch using integers Make the game LAN only where there is enough bandwidth to have 8 players with thousands of units and sending the positions and orientation etc in (almost) every frame... So I looking for better opinions, (or even tips on migrating the code to fixed-point without messing everything up...)

    Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >