Search Results

Search found 15323 results on 613 pages for 'db2 connect'.

Page 161/613 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

• WRT54GL Tomato Router in Client wireless mode to an iPhone Personal Hotspot

  - by Gordo

  I am trying to connect a router with Tomato firmware to an iPhone 4. The goal is to connect to the Personal Hotspot in Client Wireless mode. This should allow wired and wireless users to connect to the router rather then the iPhone. In theory this should be possible but I am having difficulty. Router Linksys WRT54GL Tomato 1.28.1816 firmware iPhone iPhone 4 iOS 5.1 (9B176) Carrier Rogers Wireless Personal Hotspot works with other devices, wifi/bluetooth/usb iPhone Personal Hotspot settings Mode: B/G Security: WPA or WPA2 Personal Encryption: AES Router IP: 172.20.10.1 Subnet: 172.20.10.0 Min IP: 172.20.10.2 Max IP: 172.20.10.14 maximum number of wireless tethered hosts is 5 I have followed the directions here: http://www.wi-fiplanet.com/tutorials/article.php/3810281 Ensured that the router subnet does not 'collide' with the iPhone subnet. Here is the configuration of the Tomato 'Basic - Network - Wireless' section: http://i.stack.imgur.com/pbmTB.png I have tried several variations of this configuration, but nothing seems to work. NOTE: I have successfully connected to my own wifi network in Wireless Client mode, so I am confident that there are no bad cables or other hardware issues. I would prefer to use Tomato, but DD-WRT maybe my only other option. Thanks!

  Read the article

• Windows 7 Automatically Connecting To Unsecured Wireless Networks On Startup

  - by Xtend

  Most of the questions on this topic related to folks connecting to somebody else's wireless network when their own was available and could remedy the situation by going to their connections and unchecking the "connect automatically" box. See this: " Avoid automatically connecting to wireless network on windows 7 " as an example. In my situation, I've noticed that Win 7 will automatically connect to any unsecured wifi network - even if I have never connected to it in the past. If I am traveling and boot Win 7, it will start and connect to what appears to be the best signaled unsecured network without prompting me for confirmation (note: in the above link, "Naveen" seems to have same problem). Obviously, that is a security concern to me. Further, when I open "Network and Sharing" and "Manage wireless networks" the network is not displayed (probably because I labelled it a public network). Again, these are new, never connected with before, wireless networks. I always promptly disconnect from them but don't want to have to be on constant guard for an auto connection to a malicious network. This began about a month ago, as I recall, Win 7 did not behave like this in the past, I didn't monkey with wifi settings, and don't use a 3rd party connection manager. I did have to download some internet security certificates for army website access but I don't think that should mess with network settings. Any ideas how I can tell Win7 cease automatically connecting to networks or, at least, to prompt me for a confirmation before connecting?

  Read the article

• IRC server connecting to another server

  - by Oxinabox

  I'm setting up an IRC server using IRC-Hybrid, I want my server to connect to another server, so that people on my server can connect to channels on that other server. I know this can be done, the GIMP IRC, is the same as the GNOME IRC My ircd.conf contains the following: connect { name = "aabstractname"; host = "128.64.2.1; send_password = "somepass"; accept_password = "somepass"; encrypted = no; port = 6667; class = "server"; autoconn = yes; compressed = yes; fakename = "irc.sd.dom.asn.au"; }; So when i run: /etc/init.d/ircd-hybrid restart it should be connecting to 128.64.2.1, but the log on 128.64.2.1, doesn't show anything Do I need entry on the host 128.64.2.1? I can't find any documentation for ircd.conf I'ld really like that documentation so I can check all my settings are right.

  Read the article

• Mounting any Windows share from OS X 10.7.5 suddenly stopped working

  - by user2169619

  I have problem with mounting Windows network shares from my OS X 10.7.5 - it worked but it stopped and nothing helps and nothing in logs. Here what I get when trying to mount it manually: mount -t smbfs //10.0.0.7/d /tmp/test When doing sniffing with tshark - no packet it sent through and I get immediately return from the command: mount_smbfs: server connection failed: Unknown error: -1 Nothing in /var/log/syslog.log and /var/log/kern.log. The Finder does not work either - it throws an error that something is wrong (in czech thus I'm not sending the message here). I just cannot connect to any network shares. In virtual Windows 7 in Parallels Desktop I can connect successfully, but not within the network share (so the Win7 is behind OS X NAT) but only with its own IP address. The Windows server share is on the same network segment connected through switch. Any advice how to debug and what can be wrong? I spent hours to find solution on Google and here but no-one with this kind of problem and I do not know how to further debug it since there is no meaningful log / trace etc. I can ping 10.0.0.7 and I can connect to FTP server on 10.0.0.7 - the Windows machine (XP) has firewall completely turned off. The problem is that with tshark, I'm not seeing any packet sending to 10.0.0.7 so it's not even trying to reach the server.

  Read the article

• Postgresql connection refused

  - by Jonathan

  I'm trying to remotely connect to my postgresql database. I have two virtual machines set up both running ubuntu 14.04. I am trying to connect to the second vm using the first vm using psql -h 10.0.1.23 -U postgres -d postgres But I receive the error: Could not connect to server: Connection refused Is the server running on host "10.0.1.23" and accepting TCP/IP connections on port 5432? I have changed the pg_hba.conf and added host all all 10.0.1.64/24 md5 host all all * md5 host all all 0.0.0.0/0 md5 And changed the postgresql.conf listen_address=" * " In an attempt to allow all incoming connections. I have also tried to change the firewall settings, but I am unsure of whether or not the ports are properly listening for the connection. Edit: Output of netstat -an | grep -E '^tcp[^6].*LISTEN' tcp 0 0 127.0.1.1:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:23 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:5432 0.0.0.0:* LISTEN

  Read the article

• SQL Server Instance login issue

  - by reallyJim

  I've just brought up a new installation of SQL Server 2008. I installed the default instance as well as one named instance. I'm having a problem connecting to the named instance from anywhere besides the server itself with any user besides 'sa'. I am running in mixed mode. I have a login/user that has a known username. Using that user/login, I can properly connect when directly on the server. When I attempt to login from anywhere else, I recieve a "Login failed for user ''", with Error 18456. In the log file in the server, I see a reason that doesn't seem to help: "Reason: Could not find a login matching the name provided.". However, that user/login DOES exist, as I can use it locally. There are no further details about the error. Where can I start to find something to help me with this? I've tried deleting and recreating the user, as well as just creating a new one from scratch--same result, locally fine, remotely an error. EDIT: Partially Resolved. I'm now passed the base issue--the clients were trying to connect via the default instance. I don't know why. So, once proper ports were opened in the firewall, and a static port assigned to the named instance, I can now connect--BUT ONLY if I specify the connection as Server,Port. SQLBrowser is apparently not helping/working in this case. I've verified it IS running, and done a stop/restart after my config changes, but no difference yet.

  Read the article

• Setting up virtualbox for outside access

  - by Morgan Green

  I have a computer running a server that my subdomain on my shared hosting account points to. IE subdomain.mydomain.org goes to my home server. Now then; what I'm wanting to do is be able to access my VirtualBox servers through that subdomain and a different port. E.G Ubuntu Virtual Box Server 1 Username:Ubuntuhost1 Password:MyUbuntuHost1 Port:4000 Internal IP: 192.168.1.60 External IP: 24.29.138.45 Ubuntu Virtual Box Server 2 Username:UbuntuHost2 Password:MyUbuntuHost2 Port:4001 Internal IP: 192.168.1.61 External IP: 24.29.138.45 Now I want to be able to access RDP number 1 through Port 4000, but if I access Port 4001 it will connect to the server on port 4001; both using the same subdomain. The next issue is the fact that even though I know what the IP addresses are on the router for the virtualbox hosts through ifconfig it doesn't change the fact that they don't show up on the router. If anyone knows how to configure this to work please help me out because I've been racking my brain to the highest extent I can. Alright; here's an edit to clarify more; Sorry. My ports on the router are edited to forward Port 4000 on Internal IP 192.168.1.63 (My Ubuntu Internal IP address) Now when I go to my Router Home Page my VirtualBox Internal IP Address doesn't show on the attached device listings, so I set up port forwarding anyways to the VirtualBox Internal IP. My end goal is when I connect to mydomain.org and I connect through port 3389 it takes me to my host computers server, but if I put in mydomain.org and go through port 4000 it's going to redirect to my VirtualBox server; Is this even possible? Sorry; I'm trying to clarify the most I think I can I just don't know how else to explain my issue.

  Read the article

• VGA to S-Video/Video converter showing mashed up picture.

  - by Matthijs Wessels

  Earlier I asked this question: *http://superuser.com/questions/132374/does-the-lenovo-t60p-vga-port-support-an-s-video-signal As a result I acquired the following item: http://cgi.ebay.nl/ws/eBayISAPI.dll?ViewItem&item=250588098582&ssPageName=ADME:B:EOIBSA:NL:1123 Yea I'm a cheapass... Anyway, it just arrived and now I am trying to get it to work... The manual is not very informative other than telling me, this is the vga in, this is the vga out, this is the s/video out etc. Plus it tells me the system should support the following resolutions@refresh rate: 640x480@60/72/75Hz 800x600@60/75Hz 1024x768@60Hz I can connect it to my laptop and then I connect the S/Video and the Video to my tv which only gives me a blurred image (like when you set your monitor to a resolution it doesn't support). The VGA out however works fine to my tft monitor. The are two switches on the converter. I think one switches between s/video and video and the other between PAL and NTSC. But alas, no combination seems to give a better picture (it does give a different picture). Can anyone help me to solve this problem? I have downloaded this program called powerstrip, but I have no idea how to use it and if it can even solve my problem... Thanks in advance. I use Windows XP on a Lenovo t60p and I try to connect it to a Philips 32PFL7403D/12 LCD TV from VGA to a converter to S-video or video.

  Read the article

• Implementing an isolated guest WLAN via IPSec VPN on Windows

  - by sysadmin1138

  We are attempting to set up a guest WLAN network that is isolated from the rest of our network. This is proving difficult due to a couple of technical reasons. My first choice was to use a separate VLAN, on which our Firewall's handy WLAN port would handle DHCP, DNS and the network isolation we need. Unfortunately, due to the fact that our main office and our Internet connection itself are in different locations connected by way of a Metro Ethernet connection, I'm at the mercy of our ISP for VLAN transit. They won't pass a second VLAN between our two sites. And my hardware doesn't support 802.1ad "Q-in-Q", which would also solve this problem. So I can't use the VLAN method for isolation. At least not without spending money. As our Firewall can handle IPSec site-to-site VPN connections, I hope it is possible to connect a Server 2008R2 (standard) server I have in the office location to the WLAN and provide gateway services to the firewall. Thusly: Unfortunately, I don't know if it is possible to connect the two this way. The firewall has a pretty flexible IPSec/L2TP implementation (I've used it to connect iPads in the wild), but is neither Kerberized or supports NTLM. The Connection Security Rules view on the Windows server seems to get close to what I think needs to be done, but I'm failing on figuring out how to get it to do what I need it to do. Is this even possible, or do I need to pursue alternate solution?

  Read the article

• Configuring network route between two routers on home network

  - by Paul

  I have a home network - the main router connected to the internet (and has wifi) is a Netopia box. Connected to it is a Linksys router. Everything currently works - I can connect via the wireless network and get to the internet. Machines connected to the Linksys can connect with each other and connect to the internet. Both routers are configured to serve addresses via DHCP (Netopia 192.168.1.1 - 192.168.1.99), Linksys (192.168.0.1 - 192.168.0.100). Here's how they are connected: Internet <-> Netopia w/wifi (192.168.1.254) <-> Linksys (192.168.0.1) I decided I really need to allow wireless connections to also communicate with machines behind the Linksys router. Currently the Linksys is configured to obtain an IP address via DHCP. I thought this would be straightforward. I configured the Linksys to have a static IP address: IP: 192.168.1.100 Mask: 255.255.255.0 GW: 192.168.1.254 Then I configured a static route on the Netopia: Network: 192.168.0.0 Mask: 255.255.255.0 GW: 192.168.1.100 So it should now look like this: Internet <-> Netopia w/wifi (192.168.1.254) <-> (192.168.1.100) Linksys (192.168.0.1) I reset both routers. I cannot ping the Netopia (192.168.1.254) from inside the Linksys network, and if I attempt to ping 192.168.0.1 from a wifi connection I get a "Destination host not available" error. Obviously I'm missing something, but I'm not sure where. Any ideas on what I'm missing?

  Read the article

• SASL - Plaintext password not accepted - Encrypted works

  - by leviathanus

  I have a very strange issue! SASL does not work properly, as it does not accept plain-text passwords (like Outlook sends them) Oct 2 10:35:09 srf cyrus/imap[4119]: accepted connection Oct 2 10:35:09 srf cyrus/imap[4119]: badlogin: [217.XX.XXX.140] plaintext [email protected] SASL(-1): generic failure: checkpass failed Now I switch to "Encrypted password" in Thunderbird. I have the same issue as Outlook above on Thunderbird if I turn on "Plain Password"): Oct 2 10:40:40 srf cyrus/imap[14644]: accepted connection Oct 2 10:40:41 srf cyrus/imap[14622]: login: [217.XX.XXX.140] [email protected] CRAM-MD5 User logged in Same with Postfix: Without Oct 2 10:42:48 srf postfix/smtpd[17980]: connect from unknown[217.XX.XXX.140] Oct 2 10:42:48 srf postfix/smtpd[17980]: warning: SASL authentication failure: cannot connect to saslauthd server: Permission denied Oct 2 10:42:48 srf postfix/smtpd[17980]: warning: SASL authentication failure: Password verification failed Oct 2 10:42:48 srf postfix/smtpd[17980]: warning: unknown[217.XX.XXX.140]: SASL PLAIN authentication failed: generic failure With "Encrypted password": Oct 2 10:45:27 srf postfix/smtpd[21872]: connect from unknown[217.XX.XXX.140] Oct 2 10:45:28 srf postfix/smtpd[21872]: 50B3A332AAB: client=unknown[217.XX.XXX.140], sasl_method=CRAM-MD5, [email protected] Oct 2 10:45:28 srf postfix/cleanup[21899]: 50B3A332AAB: message-id=<[email protected]> Oct 2 10:45:28 srf postfix/qmgr[6181]: 50B3A332AAB: from=<[email protected]>, size=398, nrcpt=1 (queue active) Oct 2 10:45:28 srf postfix/smtpd[21872]: disconnect from unknown[217.XX.XXX.140] Config: /etc/imapd.conf:sasl_mech_list:LOGIN PLAIN CRAM-MD5 and /etc/postfix/sasl/smtpd.conf:mech_list: LOGIN PLAIN CRAM-MD5 I have no idea where to dig. Please advise.

  Read the article

• Can't Configure IBM 8275-416 Switch Via Serial

  - by Sean M

  I am attempting to configure an IBM 8275-416 switch (I found a manual here) via serial connection. However, when I connect with HyperTerminal, the output contains a lot of garbage characters. It's pretty much unusable, because there's enough layout-breaking text-gunk that it's very difficult to determine what's actually being displayed. . I was able to reset the switch to factory defaults via the terminal interface, so I know that it's not entirely broken. It also performs basic functions all right (i.e., you plug in clients and Ethernet cables - they can connect to clients plugged into other ports) - but I'd like it to do more than that (VLANs yay). I don't know if its in-band UI is operational or not, because I can't get the terminal interface to behave well enough to properly turn on the web/SNMP UI. So that's not available. Things I've tried: - Changing the encoding: HyperTerminal lets me choose between Standard JIS and Shift-JIS. Neither setting fixes the issue. - Checking emulation settings: The manual demands VT100, 19200 baud, 8 data bits, and such: I have faithfully applied these settings, both in HyperTerminal's settings and in the properties of the COM1 port in Device Manager (connecting from a Windows machine). - Restoring to factory defaults: See above. Things that it could be, but that seem unlikely: - Cabling: Couldn't find a proper null-modem cable, so used two 232-to-RJ45 adapters. But if it was a problem with the cable, wouldn't it be more likely to not connect or do input at all, rather than just garble the text? Since I was actually able to perform the reset-to-factory defaults operation, I don't think it's this. - Device as a whole broken: It is a decade and change old, so it's possible that it's just dying slowly. Again, though, it seems like there would be more symptoms than just garbled text in the terminal. What else can I try to get a sane interface to this switch?

  Read the article

• Using VMware Guest OS to enable Host OS to ssh to remote network

  - by Reuben L.

  Basically I have an issue because my host OS is 64-bit Linux Mint (Ubuntu derived) and it doesn't seem to be compatible with the Juniper Network Connect that is used by the network at my workplace. Thus, I am unable to ssh from terminal to the network. I can't make changes to the workplace network either so that leaves me with looking for solutions on my end. The main reason for me to access the network from home is to check on my running processes or to issue more commands to a few workstations. Putty is the desperate choice I usually make but it means I have to reboot to Windows and also have limited control. I've tried several other methods and they have all failed. Recently, I setup a VM with Windows 7 as the guest OS. Now half my problems are fixed as I don't have to physically reboot the system - I just have to engage Juniper Network Connect on the VM. However, I would still like to use my Linux terminal to ssh to the network. It sounds plausible that I could somehow manipulate ports to connect to the remote network from the host OS tunneled through the guest OS, but I really have no clue how to do so... Can anyone help?

  Read the article

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• Setting Remote Desktop to allows IPv6 connections

  - by Garrett

  Setup: Basically I have 3 machines (2 virtual and 1 physical) that I would like to be able to RDP in to from outside my NAT (a router). The VMs are Windows 7 and Windows XP, both fully patched with Teredo installed and working, both running in VirtualBox (their host also has Teredo working, though I'm not sure if that matters). They both have bridged network adapters with promiscuous mode enabled. The physical machine is Windows 7 fully patched with an HFS server running on it and a dynamic DNS set up for my public IPv4 address and port forwarded. It also has Teredo installed and working. Symptoms: According to http://test-ipv6.com/ all 3 have public IPv6 addresses, and they can all connect to http://ipv6.google.com/. I can ping the XP VM from the host it's running on but I cannot ping it from any other machine. Also, I cannot ping either of the other machines from anywhere. I cannot connect to any of them over RDP from IPv6, however I can connect to all of them through IPv4. Any ideas what is going wrong?

  Read the article

• Easiest way to allow direct HTTPS connection in Intercept mode?

  - by Nicolo

  I know the SSL issue has been beaten to death I'm using DNS redirect to force my clients to use my intercept proxy. As we all know, intercepting HTTPS connection is not possible unless I provide a fake certificate. What I want to achieve here is to allow all HTTPS requests connect directly to the source server, thus bypassing Squid: HTTP connection Proxy by Squid HTTPS connection Bypass Squid and connect directly I spent the past few days goolging and trying different methods but none worked so far. I read about SSL tunneling using the CONNECT method but couldn't find any more information on it. I tried a similar method in using RINETD to forward all traffic going through port 443 of my Squid back to the original IP of www.pandora.com. Unfortunately, I did not realize all other HTTPS requests are also forwarded to the IP of www.pandora.com. For example, https://www.gmail.com also takes me to https://www.pandora.com Since I'm running the Intercept mode, the forwarding needs to be dynamic and match each HTTPS domain name with proper original IP. Can this be done in Squid or iptables? Lastly, I'm directing traffic to my Squid server using DNS zone redirect. For example, a client requests www.google.com, my DNS server directs that request to my Squid IP, then my transparent Squid will proxy that request. Will this set up affect what I'm trying to achieve? I tried many methods but couldn't get it to work. Any takes on how to do this?

  Read the article

• Xubuntu stuck after login

  - by viraptor

  How can I debug an issue with Xubuntu 12.04 (fresh install) which just waits idle after a login for about 30 seconds? The login screen is delayed correctly. After login, I get my desktop background, but no panels or auto-starting apps. It doesn't seem to be an authentication/pam issue, because I can login without delay at the console while the graphical session is still stuck. There's no disk or cpu activity and no obvious respawning of any process when I look at htop. There's nothing obviously wrong in .xsession-errors. Most interesting errors: openConnection: connect: No such file or directory cannot connect to brltty at :0 WARNING: gnome-keyring:: couldn't connect to: /tmp/keyring-wFn4VR/pkcs11: No such file or directory ... (polkit-gnome-authentication-agent-1:2131): polkit-gnome-1-WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The nam e org.gnome.SessionManager was not provided by any .service files ** Message: applet now removed from the notification area ** Message: using fallback from indicator to GtkStatusIcon ... (xfce4-indicator-plugin:2176): libindicator-WARNING **: IndicatorObject class does not have an accessible description. ... (xfce4-indicator-plugin:2176): Indicator-Application-WARNING **: Unable to get application list: Operation was cancelled Bootchart seems to end before I login, so it's not that helpful. Where else can I look for information?

  Read the article

• use ssh tunnel with phpmyadmin

  - by JohnMerlino

  I been using ssh tunnel to bypass firewall of remote mysql server. On my Ubuntu 12.04 installation, it works via the terminal and it works when using a program called mysql workbench. However, that program freezes often and I want to try phpmyadmin as an alternative. However, I cannot connect to remote server using ssh tunnel on phpmyadmin, albeit I can connect locally. These are the steps I've tried: 1) Open a tunnel, listening on localhost:3307 and forwarding everything to xxx.xxx.xxx.xxx:3306 (used 3307 because MySQL on my local machine uses the default port 3306): ssh -L 3307:localhost:3306 [email protected] So now I have the port for tunnel open and I have my local mysql installation default port: $ netstat -tln Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:3306 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:3307 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN ... 2) Now I can easily connect to remote server via localhost using the terminal: $ mysql -u user.name -p -h 127.0.0.1 -P 3307 Notice that I expicitly identify 3307 as the port, so traffic forwards to the remote server, and hence it logs me in to the remote server. Unfortunately, the localhost/phpmyadmin local login interface doesn't allow you to specify a port option. So I modify the config-db.php file and change the $dbport variable to 3307, under the impression that the phpmyadmin interface will now work with port 3307: $ sudo vim /etc/phpmyadmin/config-db.php $dbport='3307'; Then I restart the mysql server. Unfortunately, it didn't work. When I use the remote credentials to login, it gives me error: #1045 Cannot log in to the MySQL server

  Read the article

• What methods are available for updating a non-Internet-connected VMWare ESXi host?

  - by romandas

  I have a stand-alone installation of VMWare vSphere Essentials, with a vCenter Server and 3 ESXi 4.0 host servers. The environment is intended to remain as a stand-alone network, with the exception that I can "float" a workstation or server between the 'Net and the VMWare network for patches and maintenance. With other installations, where the Internet is available, I've used the vSphere Host Update utility to connect to VMWare and then apply the patches to the ESXi hosts. My problem is that this utility does not seem to function if it cannot connect to both VMWare and the ESXi host at the same time, as the scan for patches function will not scan the server without connecting to VMWare's site to sync its repository first. Even if I sync it, disconnect from the 'Net and connect to the VMWare network, it still won't scan hosts for required patches -- it will prompt for syncing with VMWare and if you click No to syncing, the scan does not occur. Does anyone know of other options for updating the ESXi hosts in some automated fashion? I believe I can manually pull down required patches and apply them, but this will not scale well, and in the future I'm sure I'll want something a bit more scalable.

  Read the article

• System and Router configuration for setting up a home firewall based on Zentyal

  - by Ako

  I am not much of a system administrator, so please be patient if this looks too simple for you. I have a several computers at home, and all of them connect using an ADSL modem/router (and Wireless AP). I have been attacked several times (mainly from Russia and Ukraine), so I thought I should have some kind of firewall, besides the ESET firewall on my Windows 7. So now I have these (new) configuration: I have a small ADSL modem (Zyxel brand) which has only one Ethernet port. This modem is used to connect to internet and is configured in NAT mode. The interface has is configured with IP address 192.168.1.1. I have an old PC and I have installed zentyal on it. It has two Ethernet ports, eth0 and eth1. Eth0 is connected to the Zyxel modem with IP 192.168.1.2 and is checked as the WAN interface (external). I have another ADSL modem which is also a router with 4 Ethernet ports and Wireless AP. One of the Ethernet ports is connected to eth1 on Zentyal box. The Ethernet port's IP is 192.168.2.1 and Zentyal's eth1 is 192.168.2.2. Now, I want to enable other computers to connect to internet through the router both using Wireless and Ethernet. The problem is that I don't know how to configure the router so it routes connections to the Zentyal box. Does anyone have any clue? Again I am sorry if this looks stupid. Thanks.

  Read the article

• Permission denied (publickey,gssapi-with-mic,password) ssh error

  - by zentenk

  Heads up I'm a noob with linux and networking. I set up a ubuntu server and I have a static ip for my network. When I try to connect to the server at home (external), it prompts me to log in. I supply the correct password (or incorrect pw), I get the error Permission denied, please try again. and after 3 times I get Permission denied (publickey,gssapi-with-mic,password) I am however able to connect with SSH from another computer in the same network with ssh < internal ip of server > I'm connecting with mac os x and my config file is vanilla. Note: During installation of ubuntu it says I don't have a default route or something while doing auto network configuration, but I ignored it and continued the installation, could this be the problem? EDIT: I have tried the below, I have nothing in hosts.allow and also iptables shows the ports that I have allowed, which is 22. I checked the auth.log, and there is nothing when I connect to it remotely (even when it says permission denied). I have tried connecting to it internally and the correct authentication logs show. Any idea whats wrong?

  Read the article

• Why does my computer sometimes not identify my wireless network, or others, that it always connects to?

  - by Emile Erasmus

  I have a vista operating system. Sometimes my computer will not connect to the wireless network (internet) when I start up my laptop. This happens at different places on occasion, and it is very random. It tries to connect, but can not identify the network (it does recognize the wifi name). So at the end it connects, but with limited connectivity. It can not be the hardware because all other computers connect to it fine at the same time. And it happens at different places, mostly home, but sometimes at coffee shops, etc. And then in a day or two when I start up my laptop it is all of a sudden working again. (restart does not solve the problem). I have tried all the trouble shooting options windows offers, restarting the notebook, switch modem on and off, switch laptop wifi on and of, deleted the wifi memory from the laptop and reconnected with the password as if it was the first time, everything. If it does not work at one place it does not mean it won't work at another. Example it won't work at home, then I go to coffee shop and it works, then get back home and it don't. Anyone encountered this before?

  Read the article

• Wireless Access Point stopped working

  - by Alex Pritchard

  I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

  Read the article

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• Internet connection problem,ping ok , but outlook and browsers dont work

  - by Ashian

  Hi, From some days ago I have a big problem on my laptop( run windows xp sp3) When I connect to internet I can ping web sites but when try to browse them some times it work correctly and some times the connection to server intrupted and I have to refresh the page several times. in this case browser show a connection problem immediatly after I click on address bar or a link on page( wihtout any try to connect to server) I use FireFox and opera and both of them have this problem. try another ISP and still I have this problem. I didnt use any proxy server and check the proxy setting. In this case Outlook also can't connect to mail server. this problem anfter some time or after restart windows have been fixed for a while. I check for virus and can't find anything. Is there any idea how can I fix it? UPDATE: Thanks for your responses. I test them , also I use Open DNS setting and that dosent help me. last night I see that my local web application ( such as Adsl modem config web site , and sites that I set up on windows xo IIS ) aslo can't open and Internal Communication error apears ( Opera Message) that didnt relate to DNS settings or Internet connection.

  Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >