Search Results

Search found 39511 results on 1581 pages for 'exc bad access'.

Page 161/1581 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

• Libvirt/KVM in NAT: can't access from host (and can't forward)

  - by SharkWipf

  I'm trying to set up a port forward to a KVM guest, managed through Libvirt on Debian 6. The VM is running in NAT, through the "default" network. This all runs fine, the VM has full internet connection. However, the host cannot reach the vm internally. Neither ping, nc nor nmap on the NAT network give any signs of the VM. Due to this, the normal iptables forwarding rules don't work either. $ cat /etc/debian_version 6.0.5 $ libvirtd --version libvirtd (libvirt) 0.9.11.3 $ kvm --version QEMU emulator version 1.0 (qemu-kvm-1.0+dfsg-11, Debian), Copyright (c) 2003-2008 Fabrice Bellard ifconfig: eth0 Link encap:Ethernet HWaddr 54:04:a6:f1:6f:10 inet addr:x.x.x.x Bcast:x.x.x.x Mask:255.255.255.x inet6 addr: fe80::5604:a6ff:fef1:6f10/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118902 errors:0 dropped:0 overruns:0 frame:0 TX packets:142357 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:13247173 (12.6 MiB) TX bytes:95163190 (90.7 MiB) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:230646 errors:0 dropped:0 overruns:0 frame:0 TX packets:230646 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:204577107 (195.0 MiB) TX bytes:204577107 (195.0 MiB) virbr0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:666759 (651.1 KiB) TX bytes:400701 (391.3 KiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:e2:d2:60 inet6 addr: fe80::fc54:ff:fee2:d260/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:125687 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:739803 (722.4 KiB) TX bytes:6886609 (6.5 MiB)

  Read the article

• Remote access to server via service control panel for non-admin user in Windows 2008

  - by user2278

  I'm trying to configure my Windows 2008 servers so that my developers can view their status without needing to log on to the box or be an admin. Unfortunately, the permissions set in Windows 2008 for remote non-admin users don't include the ability to enumerate or otherwise query services. This causes anything that contacts the SCM on the far end to fail (Win32_Service, sc.exe, services.msc etc). How do I set up permissions so that they can at least list the services and see if they are running?

  Read the article

• Cannot access boot menu with compaq 8510p

  - by pinouchon

  I have a problem with my HP compaq 8510p laptop: when I start it, the fan starts and the power light is on, but the screen displays nothing. When I insert a bootable hard drive, it activates the hard drive light (meaning that the CD is recognized) but it stops after a few seconds. Same thing with any hard drive: the drive is recognized but does not boot. What I've tried so far: Changing the hard drive or booting with no hard drive (same problem) Plugging anoher display via VGA : no display on the other screen Inserting a windows-7 CD (same problem) Booting only on battery, with battery and power cable, only with power cable (same problem) So it looks like something is preventing the laptop from booting and displaying the boot menu. Do you have experienced something similar with a laptop ? What could be wrong ? The laptop is out of warranty. The system used to be windows-7 x64. Edit: I went to the help desk of my university. A guy took a look (he also tried to plug an external screen) and said that the computer is dead: on the HP laptops eventually the GPU card dies and so does the motherboard because they are linked. He saw this many times, and even if I can fix the problem, the laptop would crash again after a while. Do you have similar experience with HP laptops ? (mine is 4 years old) Edit 2: Believe it or not, my laptop is magically working again. I have no clue about what is going on. Now it is like starting and old car: when you turn it on you secretly hope it will actually start... With that said, I expect my laptop to break again in the near future (its an HP after all) and I will accept an answer or add my own accordingly. Edit 3: As expected, the laptop is down again. This time, sometimes when I power it up, it shuts down automatically after 3 seconds, sometimes not at all. In addition, when it does not shut down on its own, the power button does not work : the only way to shut it down is by unplugging the battery. As before, the screen is black, and only the power and battery lights are on. (the other ones: hard drive and wifi are off). I have tried to plug in another power plug, removing the battery and removing the hard drive without success. I might buy another laptop. I've brought the laptop to a repair shop. The problem is indeed that the graphic card is down. It will be replaced by a new one.

  Read the article

• Apache directory access with virtual host

  - by alexeygaidamaka

  I have a virtual host with a configuration like that. When i'm trying to get into foobar.com/dir providing valid username/password pair i get 403 forbidden page instead of that directory contents. www.foobar.com/dir has 777 rights, .httpaswd is chmoded 644. But i can't figure out why i am still not seeing contents. Please, give me a hint. ServerAdmin webmaster@localhost ServerName www.foobar.com ServerAlias www.foobar.com DocumentRoot /var/www/foobar <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/foobar> Options -Indexes FollowSymLinks AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> <Directory /var/www/foobar/dir> AllowOverride AuthConfig AuthName "Authorize yourself, please!" AuthType Basic AuthUserFile /etc/apache2/.htpasswd AuthGroupFile /dev/null Allow from All Order Allow,Deny Require valid-user

  Read the article

• Cannot access SVN repository from another host within the LAN

  - by akaii

  I'm trying to connect to a repository I've set up on our server from another host on the same network, but the connection is failing. checkout command: svn checkout svn://192.168.11.192/ error: Can't connect to host '192.168.11.192' : Connection refused I tried probing port 3690 with telnet, and I can't seem to connect that way either. I thought the port might be blocked, so I added an entry for port 3690 in sysconfig/iptables, but it doesn't seem to have had any effect at all. I'm sure svnserve is running, because I can checkout the repository on server using the same command above. What can I possibly try next?

  Read the article

• Constantly visible notification and access icon for Empathy in Gnome 3

  - by aef

  Since a short while I'm using Ubuntu Oneiric Ocelot (11.10) with gnome-shell (Gnome 3) and I'm trying to get accustomed to the default Empathy Instant Messaging client. One mayor problem for me (coming from Gnome 2 and Psi) is that there is no constantly visible icon which makes it clear (for example by changing its icon or showing an animation) if there are incoming messages which I did not read already and which lets me jump into them with one click. Also I'm missing a way to bring up the contact list or hide it away with a click. I sometimes have real problems even figuring out how to even open the contact list up again. Is there a Gnome 3 extension or some other trick available to display such a notifier in the top bar? I'm talking about something just like the sound and network controls which are already located there. I know that there are notifications in the lower notification area (former system tray), but as it is only visible as I move the mouse in the lower right corner of the screen, its useless for me.

  Read the article

• Access Page property from ASP.NET custom control

  - by Farinha

  How do I access a base page property from a UserControl that is part of that page?

  Read the article

• Current trends in Random Access Memory speed [closed]

  - by Vetal

  As I know for now because of laws of Physics there will be not any tangible improvements in CPU cycles per second for the nearest future. However because of Von Neumann bottleneck it seems to not be an issue for non-server applications. So what about RAM, is there any upcoming technologies that promise to improve memory speed or we are stack with the current situation till quantum computers will come out from labs?

  Read the article

• Web service access fails when users password is in warning period

  - by uSlackr

  We have a number of locally installed .Net apps that communicate via web services. Authentication in IIS is handled by Windows Authentication so no additional login is required. We recently began seeing a problem where users are getting a application 403 error when there password is 14 days (or less) from expiring. As this sometime happens in the the middle of the day (login in the morning OK, but password reaches <14 days during the day), this comes as a surprise as they haven't been warned to change their password. Of course, one would expect they should be able to work until the password is expired. Any idea on what could be happening here? Why would IIS reject a login if the passsword hasn't actually expired? Can we change that behaviour? Thanks \\Greg

  Read the article

• Access to the path Server.MapPath is denied

  - by Alex

  I created one pdf document var document = new Document(); string path = Server.MapPath("AttachementToMail"); PdfWriter.GetInstance(document, new FileStream(path + "/"+DateTime.Now.ToShortDateString()+".pdf", FileMode.Create)); Now I want to download this document Response.ContentType = "Application/pdf"; Response.AppendHeader("Content-Disposition", "attachment; filename="+ DateTime.Now.ToShortDateString() + ".pdf" + ""); Response.TransmitFile(path); Response.End(); but it gave me error Access to the path '~\AttachementToMail' is denied. read / write access for IIS_IUSRS exists

  Read the article

• Unable to access my own websites from our home

  - by user2521866

  Not sure if this is the right place to ask, but i'm gonna have a shot at it. I host a couple of websites with a webhost in the Netherlands. For a couple of days now, i've been unable to connect to them from my home network. When using tracert in the cmd screen, i'm getting a timeout after about 4-5 hops. It seems fine accessing the website from anywhere, except my home network. Other PC's around the house also fail to open the websites. I've tried 'flushing my DNS' as seen in some other topics, but to no avail just yet. One of the websites: http://bit.ly/1hbqs4J I've contacted my host about it as well, but no response yet. Trying to take control of the situation myself now for as much as I can. Regards, Dave

  Read the article

• Access Specifier for methods

  - by Gogi

  Why protected/private access specifier cannot be used for classes and Interfaces ?

  Read the article

• Enabling http access on port 80 for centos 6.3 from console

  - by Hugo

  Have a centos 6.3 box running on Parallels and I'm trying to open port 80 to be accesible from outside tried the gui solution from this post and it works, but I need to get it done from a script. Tried to do this: sudo /sbin/iptables -A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT sudo /sbin/iptables-save sudo /sbin/service iptables restart This creates exactly the same iptables entries as the GUI tool except it does not work: $ telnet xx.xxx.xx.xx 80 Trying xx.xxx.xx.xx... telnet: connect to address xx.xxx.xx.xx: Connection refused telnet: Unable to connect to remote host UPDATE: $ netstat -ntlp (No info could be read for "-p": geteuid()=500 but you should be root.) Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:6379 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:37439 0.0.0.0:* LISTEN - tcp 0 0 :::111 :::* LISTEN - tcp 0 0 :::22 :::* LISTEN - tcp 0 0 ::1:631 :::* LISTEN - tcp 0 0 :::60472 :::* LISTEN - $ sudo cat /etc/sysconfig/iptables # Generated by iptables-save v1.4.7 on Wed Dec 12 18:04:25 2012 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [5:640] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT # Completed on Wed Dec 12 18:04:25 2012

  Read the article

• weird access denied issue with WMI

  - by stackunderflow1

  I'm seeing a weird access denied issue with WMI. we're trying to create a diff disk based on a parent vhd in a windows service app that runs under network service (machine account is an admin). everything works fine when we create the diff disk on other machine using wmi - we use an admin user account. however, we cannot do this on a local machine as wmi doesn't take user cred for the local machine. so thought network service account already should have access for this, it seems like it doesn't and even if we run the service under an admin service account, it fails. any pointers???

  Read the article

• Windows 7 Install command prompt can't access the C drive

  - by theouteredge

  I'm trying to create a new Windows 7 Professional VHD which I can dual boot to, following Scott Hanselman's guide to creating a bootable VHD. When I get to the command prompt in the Windows 7 installation and try to create a VHD or select/attach a pre-created VHD file I get an error saying that diskpart can't find the path specified. If I try and switch to the c drive using cd c: I see c:\ x:\something\> I already have a Windows 7 Ultimate install and my C drive is an SSD – if that makes a difference.

  Read the article

• Powershell access a single value in a table

  - by falkaholic

  this should be a really easy one but i can't seem to find an easy way. For example, in powershell and am using a CSV file, which is then used to look up some configuration data based on an ID. Here is what I have now, it works, but there has got to be a better way. $configList = import-csv "C:\myconfig.csv" $id = "5001" $configList | where-object {$_.id -eq $id} | foreach-object{ $configData = $_.configData} If use format-table etc, I always get the column header, which I would then have to cut off. Again, this has got to be really easy and this isn't a show stopper. But there has to be a better way to get just the data out of a table without the column header.

  Read the article

• web services access not being reached thru the web browser [closed]

  - by Tony

  I am trying to reference my .asmx webservices in .NET but my server is not exposed to the internet. When I put on the following address I get the message mentioned below. What's the reason for not being able to see the directory? Am I missing something in my IIS configuraction? Am I missing anything in my permissions? Just as reference I have other folders with webservices and I have the same issue. When I login to the server I am doing it with my windows user and password (I am using windows authentication). It's necessary to mention that when I put the URL I am getting a popup screen to put in my userid and password but it seems that's not able to validate since keeps asking me a couple of times. Let me know if you need more information to address this issue . http://appsvr02/Inetpub/wwwroot/DevWebApi/ Internet Explorer cannot display the webpage What you can try: It appears you are connected to the Internet, but you might want to try to reconnect to the Internet. Retype the address. Go back to the previous page. Most likely causes: •You are not connected to the Internet. •The website is encountering problems. •There might be a typing error in the address. More information This problem can be caused by a variety of issues, including: •Internet connectivity has been lost. •The website is temporarily unavailable. •The Domain Name Server (DNS) is not reachable. •The Domain Name Server (DNS) does not have a listing for the website's domain. •If this is an HTTPS (secure) address, click tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For offline users You can still view subscribed feeds and some recently viewed webpages. To view subscribed feeds 1.Click the Favorites Center button , click Feeds, and then click the feed you want to view. To view recently visited webpages (might not work on all pages) 1.Click Tools , and then click Work Offline. 2.Click the Favorites Center button , click History, and then click the page you want to view.

  Read the article

• How to know who accessed a file or if a file has 'access' monitor in linux

  - by J L

  I'm a noob and have some questions about viewing who accessed a file. I found there are ways to see if a file was accessed (not modified/changed) through audit subsystem and inotify. However, from what I have read online, according to here: http://www.cyberciti.biz/tips/linux-audit-files-to-see-who-made-changes-to-a-file.html it says to 'watch/monitor' file, I have to set a watch by using command like: # auditctl -w /etc/passwd -p war -k password-file So if I create a new file or directory, do I have to use audit/inotify command to 'set' watch first to 'watch' who accessed the new file? Also is there a way to know if a directory is being 'watched' through audit subsystem or inotify? How/where can I check the log of a file? edit: from further googling, I found this page saying: http://www.kernel.org/doc/man-pages/online/pages/man7/inotify.7.html The inotify API provides no information about the user or process that triggered the inotify event. So I guess this means that I cant figure out which user accessed a file? Only audit subsystem can be used to figure out who accessed a file?

  Read the article

• IPTables: allow SSH access only, nothing else in or out

  - by Disco

  How do you configure IPTables so that it will only allow SSH in, and allow no other traffic in or out? Any safety precautions anyone can recommend? I have a server that I believe has been migrated away from GoDaddy successfully and I believe is no longer in use. But I want to make sure just because ... you never know. :) Note that this is a virtual dedicated server from GoDaddy... That means no backup and virtually no support.

  Read the article

• I cannot access my flickr account

  - by AtanuCSE

  I was using Google account to log in to my Flickr. After several days, I entered into the Flickr account and found out that Flickr is moving into only Yahoo login. So I tried the Google login and it shows This account is not connected with any Yahoo account. Sign up for new........ or use existing etc... Can't remember the exact words. So I provided my Yahoo mail credentials. Now every time it is giving me a brand new account, rather taking me to my previous Flickr account. I can view the previous account photos, but After going there, it treated me as a outsider. New account showing me that I've not uploaded any photo. What's wrong? How can I connect with my previous account?

  Read the article

• How to access both partitions on a bootable USB flash drive in Windows

  - by Maccyjam

  I have a 16GB USB Flash Drive that is partitioned into two different sizes. The first partition contains a bootable version of Ubuntu, the second partition is for general saving of files. Windows will only recognise the first partition. I have tried using Bootice but this breaks the bootable partition. Disk Management recognises the second partition but does not allow me to do anything with it. Is there a way to make both partitions accessible by Windows and keep the USB disk bootable?

  Read the article

• LAN connection loses network access randomly

  - by bill11

  Hi, Windows 7 is a great OS but there are some problems which should be solved from Microsoft as fast as possible. On my Computer the LAN connection randomly loses its connection. I don't know why but I think this problem depends on my network driver which is only available for Windows XP (where it always worked perfectly). I can not reproduce this issue. Has anybody here had the same problem?

  Read the article

• Can't access YouTube

  - by Agentleader1

  I can not seem to connect to YouTube at all. If I connect directly to YouTube (youtube.com) I get this: And if I try to connect via video directly (youtube.com/watch?v=), I get this: Here's how this isn't a web issue: I have malware on my computer I believe. And the question here is, how do I get rid of it, or what possible issue could this be? I can verify this is not a website issue or wifi issue, I've tried to connect on another computer in my wifi, and it worked. It is the local machine issue. I've tried to get rid of malware at my best and also have tried to disable possible virus extensions. All can out as the same result: no help. Also, I am unable to find these hiding viruses. I used malware-bytes and Microsoft Security Essentials. Edit: This is OBVIOUSLY Windows. I am currently running on a laptop Windows 7 Home Premium 4gb ram 64-bit os Lifebook series manufactured by Fujitsu America, Inc. Intel(R) Core(TM) i3-3110M CPU @ 2.40GHz nslookup youtube.com:

  Read the article

• Access to local network machine

  - by Jirka Kopriva

  I have granted new setting from my domain provider. Domain with specific port is pointing on computer in local network (fixed ip) like: mydomain.com:87 -> 192.168.1.1 Local machine is running on win server 2008. Everything works fine on local network. But mydomain.com:87 is not working. Are there extra settings for win server to allow connection from outside? (Firewall is turned off while searching for working result.)

  Read the article

• How to know if a file has 'access' monitor in linux

  - by J L

  I'm a noob and have some questions about viewing who accessed a file. I found there are ways to see if a file was accessed (not modified/changed) through audit subsystem and inotify. However, from what I have read online, according to here: http://www.cyberciti.biz/tips/linux-audit-files-to-see-who-made-changes-to-a-file.html it says to 'watch/monitor' file, I have to set a watch by using command like: # auditctl -w /etc/passwd -p war -k password-file So if I create a new file or directory, do I have to use audit/inotify command to 'set' watch first to 'watch' who accessed the new file? Also is there a way to know if a directory is being 'watched' through audit subsystem or inotify? How/where can I check the log of a file?

  Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >