Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 161/600 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• Exchange 2010 sends out spam.

  - by Magnus Gladh

  Hi. I have an Exchange Server 2010, that uses a smart host to send out mails. A day ago the owner of smart host contact us and told us that we send out spam. I have try different open relay test on the net and all of them come back saying that this server is secured and can not be used as relay server. But I can see in my Exchange Queue Viewer that it keeps coming in new messages. Here is an example of how it looks. Identity: mailserver\3874\13128 Subject: Olevererbart:: [email protected] Pfizer -75% now Internet Message ID: <[email protected]> From Address: <> Status: Ready Size (KB): 6 Message Source Name: DSN Source IP: 255.255.255.255 SCL: -1 Date Received: 2010-12-09 21:46:22 Expiration Time: 2010-12-11 21:46:22 Last Error: Queue ID: mailserver\3874 Recipients: [email protected] How can I secure our exchange server more, to stop this from happening? Could I have got an virus that hooks up to our exchange server and send mail throw that? As I can see the From Address is always <, is there someway that I can stop sending mails that don't have a from address that I describe? Pleas help

  Read the article

• Routing / binding 128 IPs to one server

  - by Andrew

  I have a Ubuntu server with 128 ip's (static external ips 86.xx.xx.16), and I want to crawl pages thru different ip's. The gateway is xx.xxx.xxx.1, the main ip is xx.xxx.xxx.16, and the other 128 ip's are xx.xxx.xxx.129/255. I tried this configuration in /etc/network/interfaces but I doesn't work. It work if I remove the gateway for the aliases eth0:0 and eth0:1. I think this is routing problem. auto lo iface lo inet loopback auto eth0 auto eth0:0 auto eth0:1 iface eth0 inet static address xx.xxx.xxx.16 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:0 inet static address xx.xxx.xxx.129 netmask 255.255.255.128 gateway xx.xxx.xxx.1 iface eth0:1 inet static address xx.xxx.xxx.130 netmask 255.255.255.128 gateway xx.xxx.xxx.1 Also, please tell me how to "reset" every changes that I made in networking and routing. Update: I removed the gateway and now it works. I can reach the website thru all 128 ip's. But when I try to bind a socket connection in php to a specific ip I get no answer. socket_bind($sock, "xx.xxx.xx.xxx"); socket_connect($sock, 'google.com', 80); I tryed to use a sniffer to see the packets, and I see the packet sent from binded ip to google.com but the "connection" can't be established. I don't know anything about "route" command, but I have a feeling that this is the solution.

  Read the article

• IPTABLE & IP-routed netwok solution for HOST net and VM's subnet

  - by Daniel

  I've got ProxmoxVE2.1 ruled KVM node on Debian and bunch of VM's guests machine. That is how my networking looks like: # network interface settings auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 175.219.59.209 gateway 175.219.59.193 netmask 255.255.255.224 post-up echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp And I've got two working subnet solution auto vmbr0 iface vmbr0 inet static address 10.10.0.1 netmask 255.255.0.0 bridge_ports none bridge_stp off bridge_fd 0 post-up ip route add 10.10.0.1/24 dev vmbr0 This way I can reach internet, to resolve outside hosts, update and download everything I need but can't reach one guest VM out of any other VM's inside my network. The second solution allows me to communicate between VM's: auto vmbr1 iface vmbr1 inet static address 10.10.0.1 netmask 255.255.255.0 bridge_ports none bridge_stp off bridge_fd 0 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -t nat -A POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE post-down iptables -t nat -D POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE I can even NAT internal addresses: -t nat -I PREROUTING -p tcp --dport 789 -j DNAT --to-destination 10.10.0.220:345 My inexperienced mind is ready to double VM's net adapters: one for the first solution and another - for second (with slightly different adresses) but I'm pretty sure that it's a dumb way to resolve the problem and everything can be resolved via iptables/ip route rules that I can't create. I've tried a dozen of "wizard manuals" and "howto's" to mix both solution but without success. Looking for an advice (and good reading links for networking begginers).

  Read the article

• Trouble connecting to a local SQL server instance from the web

  - by dfarney

  We have a small network behind a firewall (WatchGuard XTM 2 series) and network switch. On our network we have multiple instances of SQL server, but 1 in specific that I would like to be able to access remotely from our website. We have a static IP address from our ISP and then all the machines on the network have a locally assigned dynamic IP address. When trying to connect to the database from outside our network how do I get the request to be directed to the proper machine / SQL instance? Is it a parameter in my connection string or something in my firewall? A few things to rule out: 1) The firewall is allowing access from the website to our network. I added the site's IP and opened up port 1433. Also, when trying to connect and monitoring the firewall no exceptions come up as they did before I added the proper IP address. 2) Remote connections on the SQL server has been setup and enabled. I've done a lot of reading up on remote connections and I am sure it has been setup properly. I am currently getting this error message on my site: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.)

  Read the article

• Play framework 2.2 using Upstart 1.5 (Ubuntu 12.04)

  - by Leon Radley

  I'm trying to get Play 2.2 working with upstart. I've been running Play 2.x with upstart since it's release and it's never been a problem. But since the release of 2.2 and the change to http://www.scala-sbt.org/sbt-native-packager/ play doesn't want to start any more. Here's the config I'm using description "PlayFramework 2.2" version "2.2" env APP=myapp env USER=myuser env GROUP=www-data env HOME=/home/myuser/app env PORT=9000 env ADDRESS=127.0.0.1 env CONFIG=production.conf env JAVAOPTS="-J-Xms128M -J-Xmx512m -J-server" start on runlevel [2345] stop on runlevel [06] respawn respawn limit 10 5 expect daemon # If you want the upstart script to build play with sbt pre-start script chdir $HOME sbt clean compile stage -mem $SBTMEM end script exec start-stop-daemon --pidfile ${HOME}/RUNNING_PID --chuid $USER:$GROUP --exec ${HOME}/bin/${APP} --background --start -- -Dconfig.resource=$CONFIG -Dhttp.address=$ADDRESS -Dhttp.port=$PORT $JAVAOPTS I've changed the JAVAOPTS to include the -J- and I've also changed the path to use the new startscript located in the /bin/ dir. I've read that upstart 1.4 has setuid and setguid. I've tried removing the start-stop-daemon but I haven't got that working either. Any suggestions would be appreciated.

  Read the article

• My Reverse DNS PTR record seems to be right, but I'm still getting bouncing email

  - by johnbr

  Hello, I have a service (statusme.com) where I let people know (for example) that their kid's soccer games are cancelled because of bad weather. We send out emails to the people who have registered. I have a second server as a backup, (vps.statusme.com) and I've set up the application to send some of the email through the second server. But I'm getting complaints from various recipient SMTP servers that the email is considered spam. So I did some investigating, and it appears that they think my reverse DNS record isn't correct. But when I look at it via various rDNS websites and instructions I found elsewhere on ServerFault, everything looks correct: jb$ host -t a vps.statusme.com 8.8.8.8 Using domain server: Name: 8.8.8.8 Address: 8.8.8.8#53 Aliases: vps.statusme.com has address 66.84.8.246 jb$ host -t ptr 246.8.84.66.in-addr.arpa 8.8.8.8 Using domain server: Name: 8.8.8.8 Address: 8.8.8.8#53 Aliases: 246.8.84.66.in-addr.arpa domain name pointer vps.statusme.com. I'm confused about what I'm doing wrong. Thanks for any suggestions.

  Read the article

• NAT via iptables and virtual interface

  - by Alex

  I'm trying to implement the following scenario: One VM-host, multiple guest VMs, each one gets its own IP-address (and domain). Our server has only one physical interface, so the intended use is to add virtual interfaces on eth0. To complicate our situation the provider uses port-security on their switches, so I can't run the guest interfaces in bridged mode, because then the switch detects a "spoofed" MAC-address and kills the interface (permanently, forcing me to call the support, which I'm sure will get them a little bit angry the third time ;) ). My first guess was to use iptables and NAT to forward all packages from one virtual interface to another one, but iptables doesn't seem to like virtual interfaces (at least I can't get it to work properly). So my second guess is to use the source IP of the packages to the public interface. Let's assume libvirt creates a virbr0-network with 192.168.100.0/24 and the guest uses 192.168.100.2 as IP-address. This is what I tried to use: iptables -t nat -I PREROUTING --src public_ip_on_eth0:0 -p tcp --dport 80 -j DNAT --to-destination 192.168.100.2:80 That doesn't give me the intended results either (accessing the server times out). Is there a way to do what I'm trying to do, or even to route all traffic to a certain IP on a virtual interface to the VM's device?

  Read the article

• How can I redirect/forward all the UDP/TCP traffic on one interface to another interface in OpenWrt

  - by Sina Sou

  I am new to networking and I have a measurement device (D) that periodically sends all its readings over few UDP multicast sockets (with different multicast IP addresses and different port numbers). That device even listens to a TCP socket simultaneously to modify its configuration on port 7234. Since the device has just a Ethernet interface for communication and I want to make it work wireless, I decided to use a very small wireless open-wrt based router that attaches to the device (D) and redirect/forward all the network traffic(Both UDP/TCP) to the router wireless interface. In order to simplify the problem assume that the Device (D) establishes following sockets (at the same time) UM_SOCK1: UDP mcast socket on 239.1.2.3 port# 50620 UM_SOCK2: UDP mcast socket on 239.1.2.4 port# 50640 TC_SOCK3: TCP DHCP/STATIC ip address 192.168.1.200 port 7234 And (D) is connected to Open-Wrt router (R) via interface en01 (Ethernet) the router has it own wireless interface on (wlan0) I want all the traffic from interface pass through wlan01 and vice versa (bi-directional) en01 <---- wlan01 What would be the minimum iptables or ... commands that I need to make this possible? Even I am wondering if traffic directing can be made easier like if the direction is not going to be based on IP addresses(not desired if the device is connected via DHCP) I would rather redirection to be Interface(en0) based or on MAC address (The best solution since my device has unique MAC address)? Thanks

  Read the article

• Managing persistent data on an Amazon EC2 web server

  - by Derek

  I've just started trying out Amazon's EC2 service for running an asp.net web app which uses a SQL Server 2005 Express database. I have some questions about how to configure and operate it best for reliability, and I'm hoping to tap into some collective wisdom here as this is my first foray into EC2. Here's how I have it configured currently: OS: Windows 2003 SQL Server Express 2005 Web content stored on an EBS Volume (E Drive) Database Data stored on an EBS Volume (E Drive) Database backups to "C Drive" and then copied off to S3. Elastic IP Address attached to the production instance. Now when I make a change to the OS configuration, I make a new AMI using the bundle feature. Unfortunately, I found that this results in significant downtime. While the bundle is created and the new instance is started. It seems that when I'm ready to make a new AMI, I should: Start up a new temporary instance. Detach the EBS volume from the production instance. Detach the IP Address from the production instance. Attach the IP Address to the temporary instance. Attach the EBS volume to the temporary instance. Create an AMI from the production instance. After the production instance restarts, reverse the attach/detach steps to put it back in production. Is this the right order of events to prevent any chance to corrupt the EBS volume? Will the EBS volume become corrupt if I detach it while a database Write is taking place? Should I snapshot the EBS volume of the production instance and attach it to the temporary instance instead? Or could taking a snapshot of the EBS volume while it's in use cause corruption? Any suggestions to improve the reliability and operations?

  Read the article

• OS X (10.6) Apache Sudden Death, Nginx not working either...

  - by Jesse Stuart

  Hi, I turned on my computer today and apache wasn't working. This is weird as its been working for the last 6 months without issue. The only thing I did which may of caused a problem, is I uninstalled a bunch of gems. This shouldn't be the issue though as apache doesn't rely on gems. I decided to give nginx a try to see if it would work and have the exact same issue. The symtoms are: I go to http://localhost and get the browsers default 404 page (not rendered by apache/nginx) No error is found anywhere (I checked all logs) Apache is rinning (also tried with Nginx) How can I debug this to find the root of the problem? I can't think of why this would be happening. I've tried repairing permissions in case this was the issue, apparently it wasn't. Everything was working the other day, and nothing changed in the apache config. Update: Here is the output of telnet localhost 80 $ telnet localhost 80 Trying ::1... telnet: connect to address ::1: Connection refused Trying fe80::1... telnet: connect to address fe80::1: Connection refused Trying 127.0.0.1... telnet: connect to address 127.0.0.1: Connection refused telnet: Unable to connect to remote host

  Read the article

• Hide/Replace Nginx Location Header?

  - by Steven Ou

  I am trying to pass a PCI compliance test, and I'm getting a single "high risk vulnerability". The problem is described as: Information on the machine which a web server is located is sometimes included in the header of a web page. Under certain circumstances that information may include local information from behind a firewall or proxy server such as the local IP address. It looks like Nginx is responding with: Service: https Received: HTTP/1.1 302 Found Cache-Control: no-cache Content-Type: text/html; charset=utf-8 Location: http://ip-10-194-73-254/ Server: nginx/1.0.4 + Phusion Passenger 3.0.7 (mod_rails/mod_rack) Status: 302 X-Powered-By: Phusion Passenger (mod_rails/mod_rack) 3.0.7 X-Runtime: 0 Content-Length: 90 Connection: Close <html><body>You are being <a href="http://ip-10-194-73-254/">redirect ed</a>.</body></html> I'm no expert, so please correct me if I'm wrong: but from what I gathered, I think the problem is that the Location header is returning http://ip-10-194-73-254/, which is a private address, when it should be returning our domain name (which is ravn.com). So, I'm guessing I need to either hide or replace the Location header somehow? I'm a programmer and not a server admin so I have no idea what to do... Any help would be greatly appreciated! Also, might I add that we're running more than 1 server, so the configuration would need to be transferable to any server with any private address.

  Read the article

• What are these isolated resource requests in Apache's access_log?

  - by Greg

  I was looking at my Apache access log and came across some strange requests. A single IP address will access several resources (mostly css style sheets and images), but no actual pages. Sometimes they are requesting a resource that no longer exists on the server, or one that is still under the web root but no longer used (e.g. a resource in an old WordPress theme). Also: The requests list no referrer I get no useful information on the IP address by looking it up There doesn't seem to be any pattern among the IP addresses that are making these requests (e.g. different countries) Are these just links from a stale cache somewhere? Could it be a sign of an attack of some sort? Here is a typical example: GET /wp-content/themes/my-theme/images/old-image.gif HTTP/1.1" 500 809 "-" "Mozilla/4.0 (compatible;)" This was one of about 10 similar requests, some for existing resources, some for older resources. There is no other sign of this IP address in access_log. Note the internal server error, which is a topic for a different thread. What I'm asking here is where would isolated requests like this come from?

  Read the article

• Having two IP Routes/Gateways of last Resort on an HP Switch

  - by SteadH

  We have an HP Layer 3 Switch that is doing IP routing between vlans. The general set up is that the switch has an IP address on each VLAN and IP routing is enabled. On our servers VLAN, we have a firewall that has a connection to the outside world. To set a IP route on the HP router, we use IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.1 where 192.168.2.1 is the address of our firewall, and the zeros essentially mean to route all traffic that the switch doesn't know what to do with out the firewall as a gateway. We're in the middle of an ISP and firewall change. I set up the new firewall and ran the IOS command ip route 0.0.0.0 0.0.0.0 192.168.2.254 (the address of the new firewall). Things started working nicely. When I reviewed the configuration of the switch though, I noticed that it did not replace the previous ip route command, but just added another route. Now, I know how to remove the old firewall route (no ip route 0.0.0.0 0.0.0.0 192.168.2.1), but what is the effect of having these two 0.0.0.0 routes? Is it switch implosion? Will a server just respond back over the route it receives the request from? I've read elsewhere that having two default gateways is an impossibility by definition, but I'm curious about this situation that our switch allowed. Thanks!

  Read the article

• Ping with explicit next-hop selection (aka Monitoring multiple default gateways)

  - by Michuelnik

  I have a linux (debian) router with two internet connections (A) and (B). (A) is preferred, (B) is fallback. I want to monitor the internet connection (and not only the availability of the gateways!) and change the default route appropriately. If (A) is not providing internet, switch to (B) If (A) is providing internet again, switch back to (A). Only problem I have is in case (2). My routing table points towards a working internet so I cannot easily detect whether internet is working over link (A) again. I am search for a ping or traceroute (or other diagnosis-tool) which can select the next-hop explicitly. ping -r looks promising, but can only ping a host on the lan. (It only has to write another destination address in the packet, damnit!) traceroute -g gateway looks even more promising and nearly does what I want - but sets source routing options which my next-hops deny. (Not within my administrative boundary...) I just want a $ping, that can: select a source interface (and address) select a next-hop on that interface ping any arbitrary ip address I could do evil trickery with policy-based routing but that would have production impact for all users. I would like to see a side-effect-free solution....

  Read the article

• How to determine if my AWS/EC2 server has been compromised / resolution?

  - by ElHaix

  I have recently seen an increase in network in/out activity on my server and am trying to determine if my AWS/EC2 instance has been compromised, and if so, how to resolve? In my security group I have: Inbound: 80 (HTTP) 0.0.0.0/0 Outbound: 80 (HTTP) 0.0.0.0/0 443 (HTTPS) 0.0.0.0/0 Using TCP-UDP Endpoint Viewer: I see a lot of w3wp.exe TCP processes with varying local ports http and numbered, as well as varying remote ports. Some processes go red/yellow/green on updates . I see Remote address for most w3wp processes are my ec2 instance, however I am seeing several to *.deploy.akamaitechnologies.com and *.deploy.static.akamaitechnologies.com with received bytes varying between 4-11 megs. I also see Ec2Config.exe, remote address: 169.254.169.254 System Process Remote Address: fetcher4-4.p.mail.ru (how can I get rid of this one?!) local port: http remote port: 33432 I am also seeing some system processes from 114.216-244-93-rdns.wowrack.com: Protocol: TCP local port: http remote port: varying As well as some baiduspider "System Process"'s. I'm afraid that my system may have been compromised, and wondering if these results are any indication of that. If so, how can I get eliminate these possible threats? I have MS Security Essentials installed.

  Read the article

• port forwarding/network settings preventing from game hosting

  - by Xitcod13

  I asked where to post this question on stackoverflow meta and they directed me here. Im on wireless connection and I want to host games in StarCraft: Brood War and i've been looking everywhere on how to accomplish that. My internet is amazingly fast so its not an internet problem (and when i play other peoples games dont experience lag) I found out that i need to have a static IP but I have already checked that i do (i downloaded a program to make my id static and it already was; The program asked for which router I used So i think it checked the router settings already) I found out that i need to allow Sc access through the firewall which i already did (i have zone-alarm but I allowed it everything possible except receiving emails lol) I have recently noticed that few people actually can join my games but most of them cannot. I dont know whats going on here. I really want to be able to host games overall how do I go about checking what is wrong with the network. Update: Alright I figured out what i did wrong in the first part I did not actually set up forwarding on the router -.- I have tried to fix my mistake. I went to forwarding options in my router (as this guide for my specific router suggests) but when i click ok I get a message incorrect ip address. 192.168.1.1 is my routers address. The default address that appears there is 192.168.1 (blank) I have set it to my computers current Ip4 adress which 192.168.1.23 I hope this works If so i will post it as an answer and mark it.

  Read the article

• Ubuntu IP Configuration - multiple subnets & interfaces

  - by HaydnWVN

  Have a 'new' mailserver running postfix on Ubuntu. We are having some problems configuring the subnets & interfaces. Basically 2 subnets (.253. & .254.) need to be connected through the 3rd subnet (.252.) where the Router is residing. # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 10.62.254.199 netmask 255.255.0.0 network 10.62.254.0 broadcast 10.62.255.255 #gateway 10.62.252.138 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 10.62.252.138 dns-search ***.com auto eth1 iface eth1 inet static address 10.62.253.199 netmask 255.255.0.0 network 10.62.253.0 broadcast 10.62.255.255 #gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-nameservers 10.62.252.138 dns-search ***.com auto eth2 iface eth2 inet static address 10.62.252.199 netmask 255.255.0.0 network 10.62.252.0 broadcast 10.62.255.255 gateway 10.62.252.138 #dns-nameservers 10.62.254.199 10.62.253.199 10.62.252.199 dns-search ***.com I have an external support company who are looking into this (they built and configured this server), but it's taking far too long... So I'm looking to highlight the mistake!

  Read the article

• Things to check for an internet-facing email server.

  - by Shtééf

  I'm faced with the task of setting up a public-internet-facing email server, that will be relaying mail for all of our other servers in the network. While the software in itself is set up in few keystrokes, what little experience I have with managing an email server has thought me that there are tons of awkward filtering techniques employed by other email systems. Systems that my own server will inevitably interact with a some point. Hence, my questions: What things should be kept in mind and double checked when setting up an email server? What resources are available for checking if my email server is set-up correctly? I'm specifically NOT looking for instructions for any given mail server, such as Exchange or Postfix. But it's okay to say: “you should have X and Y in your set-up, because when talking to server software Z, it typically tries to weed out open relays by checking for these.” Some things I've discovered myself: Make sure forward and reverse DNS are set up. Mail servers tend to do a reverse lookup for the peer IP-address when receiving. Matching a reverse look up with a follow-up forward lookup is probably employed to weed out open relays run through malware on home networks. Make sure the user in the From-address exists. The From-address is easily spoofed. A receiving mail server may try to contact the mail server in the From-domain, and see if the From-user actually exists.

  Read the article

• Does SNI represent a privacy concern for my website visitors?

  - by pagliuca

  Firstly, I'm sorry for my bad English. I'm still learning it. Here it goes: When I host a single website per IP address, I can use "pure" SSL (without SNI), and the key exchange occurs before the user even tells me the hostname and path that he wants to retrieve. After the key exchange, all data can be securely exchanged. That said, if anybody happens to be sniffing the network, no confidential information is leaked* (see footnote). On the other hand, if I host multiple websites per IP address, I will probably use SNI, and therefore my website visitor needs to tell me the target hostname before I can provide him with the right certificate. In this case, someone sniffing his network can track all the website domains he is accessing. Are there any errors in my assumptions? If not, doesn't this represent a privacy concern, assuming the user is also using encrypted DNS? Footnote: I also realize that a sniffer could do a reverse lookup on the IP address and find out which websites were visited, but the hostname travelling in plaintext through the network cables seems to make keyword based domain blocking easier for censorship authorities.

  Read the article

• Why does my Windows 8 Pro Hyper-V guest have no internet?

  - by Perplexed

  Trying to get this working on my Windows 8 Pro machine. I created an External Switch Assigned the newly available adapter to a Guest machine with Win 2008 os. My host has internet connection. Host can ping Guest, Guest cannot ping Host. Guest has no internet connection. Pasting the IP of both host and guest. HOST ========================== Ethernet adapter vEthernet (EXTSW01): Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Hyper-V Virtual Ethernet Adapter #2 Physical Address. . . . . . . . . : 9C-B7-0F-0F-D7-D0 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::5434:a9fd:8611:d207%54(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.15(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Saturday, September 8, 2012 12:34:44 PM Lease Expires . . . . . . . . . . : Saturday, September 15, 2012 12:34:44 PM Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DHCPv6 IAID . . . . . . . . . . . : 916240141 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-DC-C9-2C-9C-B7-0D-0D-D7-D0 DNS Servers . . . . . . . . . . . : 64.71.255.999 NetBIOS over Tcpip. . . . . . . . : Enabled GUEST ========================== Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual Machine Bus Network Adapter Physical Address. . . . . . . . . : 00-15-5D-3F-0F-00 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::953f:ec5c:5d84:1b50%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.20(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 0.0.0.0 DHCPv6 IAID . . . . . . . . . . . : 234886493 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-DD-2F-29-0F-15-5E-00-0F-00 DNS Servers . . . . . . . . . . . : ::1 127.0.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• Office documents on intranet all requiring second login and can't pass auth? Disable webdav?

  - by DOTang

  I am not sure what is going on, but recently all the Office documents on our intranet get prompted a second time for login and according to the error logs it looks like it's trying to use webdav to open (an editable?) version of the document to save directly on the server? We have no sharepoint server setup or anything, but this shouldn't be happening. All I want is for the document to be saved or opened from a local copy in temp like normal. Here is the log: Line 57499: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57500: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 Line 57501: 2011-04-12 15:57:10 (ip) OPTIONS (address) - 443 (username) (user ip) Microsoft-WebDAV-MiniRedir/6.1.7601 - 401 1 1326 1525 238 0 The log basically contains a bunch of these. How can I disable this behavior so that office documents that are downloaded aren't attempted to be used through webdav?? Edit: I should clarify behavior, it asks if you want to save or open it, upon choosing open open, it asks to re-authenicate, you put in the user information and the login box comes up 3 times acting like you entered the wrong password. For some users, after passing the login box the third time, it still opens up, for others their browser just locks up. It also doesn't even look like webdav is installed on our server, I see no config options in IIS for it as outlined on this page: http://learn.iis.net/page.aspx/350/installing-and-configuring-webdav-on-iis-7/#001

  Read the article

• Why Would one VLAN have no Communication on one Switch?

  - by Webs

  So the problem is we have a device or host that needs to communicate on a specific VLAN. This VLAN is not new, it is running all throughout our environment and works fine. But the VLAN was recently configured on the switch in question, a Cisco 3750. The DHCP server is handing out addresses on that VLAN with no problem. I have verified the cable between the host and switch and tried multiple hosts, but none of them can communicate or get an address. I plugged my laptop into an empty port which had a different VLAN assigned and immediately got a DHCP address. When I changed that port to the same VLAN I'm having issues with I got the same problem. The laptop just sits there and tries to DHCP an address but nothing happens. I double checked the cores and their Layer 3 VLAN config and its fine too. Plus I figured the issue couldn't be with them because the VLAN works fine everywhere else it exists. So the only other thing I can think of is the switch, but the VLAN exists on the switch and seems to be configured correctly. The trunks appear to be configured just fine as well too. Anyone have any ideas? I'm lost on this one.

  Read the article

• Is there any way to synchronize AD users with Office 365 but still be able to edit them online?

  - by Massimo

  I'm performing a migration to Office 365 from a third-party mail server (MDaemon); the local Active Directory doesn't include any Exchange server, and never had any. We will need directory synchronization in order to enable users to log on to Office 365 using their domain credentials; but it seems that as soon as you enable directory synchronization, you can't perform any action anymore on Office 365 users: all changes need to be made on the local Active Directory, and then replicated by the synchronization process. For ordinary users with a single e-mail address and standard features, this is not a big problem; but what about users which need an additional address? What if I need to configure some nonstandard setting, like "hide from address list" or a custom mailbox quota? From what I've gathered, the only supported way to do this, as you can't directly edit Office 365 objects anymore after synchronization is enabled, is to extend the local AD schema with Exchange attributes, and then manually edit them (!). Or, you can install at least one local Exchange server, and then use the Exchange administrative tools to configure the required settings. Is this correct or am I missing something? Is there any way to synchronize user accounts and password, but still be able to edit user settings directly in Office 365? If not (everything really needs to be set locally and then synchronized), is there any simpler way to do this than manually editing LDAP attributes or installing a local Exchange server?

  Read the article

• openvpn in a bridge?

  - by sebelk

  I have a somewhat tricky proble to solve. We have a wireless link between 2 building. One of them has an mikrotik and below there are some vlans. Some machines of one vlan need to use openvpn to connect to a remote private lan. I put a TP-Link WR1043ND (which those machines connect to) with openwrt with ebtables just in case I need it. I've configured openwrt in such a way that all ports belongs to the same vlan. My idea was to make things as transparent as I can. It has a bridge as follows: usr/sbin/brctl-full show br-lan bridge name bridge id STP enabled interfaces br-lan 8000.f8d111565716 no eth0.1 eth0.2 Also I've added an ebtables rule: ebtables -t broute -A BROUTING -p ipv4 -j DROP So "bridge" has only one IP address. I've installed openvpn and I'm trying to bring up the tunnel but I can't still get working. Sure, someone can says why don't you use the vpn on the mikrotik, there are some reasons, the first one is I have little experience with mikrotik and I'd want to have the vpn at hand :) The problem is that openvpn is not working, because it is complaining that I have only one Ip Address on the server side. So I set up and alias interface with another IP address but is not working either: : Rejected connection attempt from IP-Client-Side:37801 due to --remote setting Is there a way to make it work?

  Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >