Search Results

Search found 34595 results on 1384 pages for 'vendor id'.

Page 161/1384 | < Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >

• Randomely loosing wireless connexion with Cubuntu 12.04

  - by statquant

  I am presently experiencing random disconnections from my wireless network. It looks like it is more and more frequent (however I have not seen any clear pattern). This is killing me... Here is some information that should help (from ubuntu forums). Thanks for reading Machine : Acer Aspire S3 statquant@euclide:~$ lsb_release -d Description: Ubuntu 12.04.1 LTS statquant@euclide:~$ uname -mr 3.2.0-33-generic x86_64 statquant@euclide:~$ sudo /etc/init.d/networking restart * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... statquant@euclide:~$ lspci 02:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01) statquant@euclide:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 004: ID 064e:c321 Suyin Corp. Bus 002 Device 003: ID 0bda:0129 Realtek Semiconductor Corp. statquant@euclide:~$ ifconfig wlan0 Link encap:Ethernet HWaddr 74:de:2b:dd:c4:78 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::76de:2bff:fedd:c478/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:913 errors:0 dropped:0 overruns:0 frame:0 TX packets:802 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:873218 (873.2 KB) TX bytes:125826 (125.8 KB) statquant@euclide:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"Bbox-D646D1" Mode:Managed Frequency:2.437 GHz Access Point: 00:19:70:80:01:6C Bit Rate=65 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=56/70 Signal level=-54 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:71 Missed beacon:0 statquant@euclide:~$ dmesg | grep "wlan" [ 17.495866] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 17.498950] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 20.072015] wlan0: authenticate with 00:19:70:80:01:6c (try 1) [ 20.269853] wlan0: authenticate with 00:19:70:80:01:6c (try 2) [ 20.272386] wlan0: authenticated [ 20.298682] wlan0: associate with 00:19:70:80:01:6c (try 1) [ 20.302321] wlan0: RX AssocResp from 00:19:70:80:01:6c (capab=0x431 status=0 aid=1) [ 20.302325] wlan0: associated [ 20.307307] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 30.402292] wlan0: no IPv6 routers present statquant@euclide:~$ sudo lshw -C network [sudo] password for statquant: *-network description: Wireless interface product: AR9485 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 74:de:2b:dd:c4:78 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-33-generic firmware=N/A ip=192.168.1.3 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c0400000-c047ffff memory:afb00000-afb0ffff statquant@euclide:~$ iwlist scan wlan0 Scan completed : Cell 01 - Address: 00:19:70:80:01:6C Channel:6 Frequency:2.437 GHz (Channel 6) Quality=56/70 Signal level=-54 dBm Encryption key:on ESSID:"Bbox-D646D1" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000125fb152bb Extra: Last beacon: 40020ms ago IE: Unknown: 000B42626F782D443634364431 IE: Unknown: 010882848B960C121824 IE: Unknown: 030106 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101820003A4000027A4000042435E0062322F00 IE: Unknown: 2D1A4C101BFF00000000000000000000000000000000000000000000 IE: Unknown: 3D1606080800000000000000000000000000000000000000 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000 And... finally, please note that I did the following (after looking for fixes of similar problems), but unfortunately it did not work sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1

  Read the article

• How can I test database access methods in Java?

  - by javaStudent

  I want to write a test for a method that accesses a database such as following. public class MyClass{ public String getAddress(Int id){ String query = "Select * from Address where id="+id; //some additional statements resultSet = statement.executeQuery(); return result.getString(ADDRESS); } } How can I test this method? I am using Java.

  Read the article

• Validate if aTextBox Value Start with a Specific Letter

  - by Vincent Maverick Durano

  In case you will be working on a page that needs to validate the first character of the TextBox entered by a user then here are two options that you can use: Option 1: Using an array   1: <asp:Content ID="Content1" ContentPlaceHolderID="HeadContent" runat="server"> 2: <script type="text/javascript"> 3: function CheckFirstChar(o) { 4: var arr = ['A', 'B', 'C', 'D']; 5: if (o.value.length > 0) { 6: for (var i = 0; i < arr.length; i++) { 7: if (o.value.charAt(0) == arr[i]) { 8: alert('Valid'); 9: return true; 10: } 11: else { 12: alert('InValid'); 13: return false; 14: } 15: } 16: } 17: } 18: </script> 19: </asp:Content> 20: <asp:Content ID="Content2" ContentPlaceHolderID="MainContent" runat="server"> 21: <asp:TextBox ID="TextBox1" runat="server" onblur="return CheckFirstChar(this);"></asp:TextBox> 22: </asp:Content>   The example above uses an array of string for storing the list of  characters that a TextBox value should start with. We then iterate to the array and compare the first character of TextBox value to see if it matches any characters from the array. Option 2: Using Regular Expression (Preferred way)   1: <asp:Content ID="Content1" ContentPlaceHolderID="HeadContent" runat="server"> 2: <script type="text/javascript"> 3: function CheckFirstChar(o) { 4: pattern = /^(A|B|C|D)/; 5: if (!pattern.test(o.value)) { 6: alert('InValid'); 7: return false; 8: } else { 9: alert('Valid'); 10: return true; 11: } 12: } 13: </script> 14: </asp:Content> 15: <asp:Content ID="Content2" ContentPlaceHolderID="MainContent" runat="server"> 16: <asp:TextBox ID="TextBox1" runat="server" onblur="return CheckFirstChar(this);"></asp:TextBox> 17: </asp:Content>   The example above uses regular expression with the pattern  /^(A|B|C|D)/. This will check if the TextBox value starts with A,B,C or D. Please note that it's case sensitive. If you want to allow lower case then you can alter the patter to this /^(A|B|C|D)/i. The i in the last part will cause a case-insensitive search.   That's it! I hope someone find this post useful!

  Read the article

• USB Ports In Wrong Mode, How To Use usbmodeswitch?

  - by user86872

  I haven't had access to my USB ports as media devices for a couple days now. I've been reading and researching everything I can find but I can't find a good guide for usbmodeswtich or usbms that I can decipher. The USB's are fine for power, but won't support my android phone as a media device, which is killing me because I use adb everyday, and won't support my plug and play mouse any longer. Not sure what caused the switch, though I think it may be related to the suspend issue I've read about, but the solutions in those threads I read also didn't work. Below is my system information and details. System: Ubuntu 12.04, 64-bit, Dedicated Machine Machine: HP-Pavillion g6 notebook, AMD A6 Quad Core Processor USBs used for: Cooling dock, Android Debug Bridge, Wireless Mouse Attempted Mod Probe, udev restart, unable to attempt lsusb due to my own lack of knowledge. :) Last Attempt Readout: ncandiano@ncandiano-HP-Pavilion-g6-Notebook-PC:~$ sudo modprobe -r usbhid && sleep 5 && sudo modprobe usbhid ncandiano@ncandiano-HP-Pavilion-g6-Notebook-PC:~$ sudo modprobe -r usb-storage ncandiano@ncandiano-HP-Pavilion-g6-Notebook-PC:~$ sudo modprobe usb-storage ncandiano@ncandiano-HP-Pavilion-g6-Notebook-PC:~$ sudo restart udev udev start/running, process 2624 ncandiano@ncandiano-HP-Pavilion-g6-Notebook-PC:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 0461:4de7 Primax Electronics, Ltd webcam Any help would be greatly appreciated!

  Read the article

• Access Master Page Controls II

  - by Bunch

  Here is another way to access master page controls. This way has a bit less coding then my previous post on the subject. The scenario would be that you have a master page with a few navigation buttons at the top for users to navigate the app. After a button is clicked the corresponding aspx page would load in the ContentPlaceHolder. To make it easier for the users to see what page they are on I wanted the clicked navigation button to change color. This would be a quick visual for the user and is useful when inevitably they are interrupted with something else and cannot get back to what they were doing for a little while. Anyway the code is something like this. Master page: <body>     <form id="form1" runat="server">     <div id="header">     <asp:Panel ID="Panel1" runat="server" CssClass="panelHeader" Width="100%">        <center>            <label style="font-size: large; color: White;">Test Application</label>        </center>       <asp:Button ID="btnPage1" runat="server" Text="Page1" PostBackUrl="~/Page1.aspx" CssClass="navButton"/>       <asp:Button ID="btnPage2" runat="server" Text="Page2" PostBackUrl="~/Page2.aspx" CssClass="navButton"/>       <br />     </asp:Panel>     <br />     </div>     <div>         <asp:scriptmanager ID="Scriptmanager1" runat="server"></asp:scriptmanager>         <asp:ContentPlaceHolder id="ContentPlaceHolder1" runat="server">         </asp:ContentPlaceHolder>     </div>     </form> </body> Page 1: VB Protected Sub Page_Load(ByVal sender As Object, ByVal e As System.EventArgs) Handles Me.Load     Dim clickedButton As Button = Master.FindControl("btnPage1")     clickedButton.CssClass = "navButtonClicked" End Sub CSharp protected void Page_Load(object sender, EventArgs e) {     Button clickedButton;     clickedButton = (Button)Master.FindControl("btnPage1");     clickedButton.CssClass = "navButtonClicked"; } CSS: .navButton {     background-color: White;     border: 1px #4e667d solid;     color: #2275a7;     display: inline;     line-height: 1.35em;     text-decoration: none;     white-space: nowrap;     width: 100px;     text-align: center;     margin-bottom: 10px;     margin-left: 5px;     height: 30px; } .navButtonClicked {     background-color:#FFFF86;     border: 1px #4e667d solid;     color: #2275a7;     display: inline;     line-height: 1.35em;     text-decoration: none;     white-space: nowrap;     width: 100px;     text-align: center;     margin-bottom: 10px;     margin-left: 5px;     height: 30px; } The idea is pretty simple, use FindControl for the master page in the page load of your aspx page. In the example I changed the CssClass for the aspx page's corresponding button to navButtonClicked which has a different background-color and makes the clicked button stand out. Technorati Tags: ASP.Net,CSS,CSharp,VB.Net

  Read the article

• New Sample Demonstrating the Traversing of Tree Bindings

  - by Duncan Mills

  A technique that I seem to use a fair amount, particularly in the construction of dynamic UIs is the use of a ADF Tree Binding to encode a multi-level master-detail relationship which is then expressed in the UI in some kind of looping form – usually a series of nested af:iterators, rather than the conventional tree or treetable. This technique exploits two features of the treebinding. First the fact that an treebinding can return both a collectionModel as well as a treeModel, this collectionModel can be used directly by an iterator. Secondly that the “rows” returned by the collectionModel themselves contain an attribute called .children. This attribute in turn gives access to a collection of all the children of that node which can also be iterated over. Putting this together you can represent the data encoded into a tree binding in all sorts of ways. As an example I’ve put together a very simple sample based on the HT schema and uploaded it to the ADF Sample project. It produces this UI: The important code is shown here for a Region -> Country -> Location Hierachy: <af:iterator id="i1" value="#{bindings.AllRegions.collectionModel}" var="rgn"> <af:showDetailHeader text="#{rgn.RegionName}" disclosed="true" id="sdh1"> <af:iterator id="i2" value="#{rgn.children}" var="cnty">     <af:showDetailHeader text="#{cnty.CountryName}" disclosed="true" id="sdh2">       <af:iterator id="i3" value="#{cnty.children}" var="loc">         <af:panelList id="pl1">         <af:outputText value="#{loc.City}" id="ot3"/>           </af:panelList>         </af:iterator>       </af:showDetailHeader>     </af:iterator>   </af:showDetailHeader> </af:iterator>  You can download the entire sample from here:

  Read the article

• CommVault Moves Data Storage to the Cloud

  Storage management and backup software vendor CommVault is giving its Simpana software new cloud storage capabilities.

  Read the article

• Browser Game Database structure

  - by John Svensson

  users id username password email userlevel characters id userid level strength exp max_exp map id x y This is what I have so far. I want to be able to implement and put different NPC's on my map location. I am thinking of some npc_entities table, would that be a good approach? And then I would have a npc_list table with details as how much damage, level, etc the NPC is. Give me some ideas with the map, map entities, npc how I can structure it?

  Read the article

• Graphic issue on intel945 chipset

  - by peeyush tiwari

  I used Intrepid(8.10) and my graphics used to work fine with compiz effects and all(on better resolution than 1024x768).Now I have upgraded to Precise(12.04)but I use gnome classic(with compiz effects)as my desktop but the compiz effects seem not to work, only unity 2D works. When I ran lshw -c video it gives: *-display UNCLAIMED description: VGA compatible controller product: 82945G/GZ Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list configuration: latency=0 resources: memory:fea80000-feafffff ioport:dc00(size=8) memory:e0000000-efffffff memory:fea40000-fea7ffff Sysinfo shows: Display Resolution 1024x768 pixels OpenGL Renderer Gallium 0.4 on llvmpipe(LLVM 0x300) X11 Vendor The X.Org Foundation On SystemSettings: Memory 993.3 MiB Processor Intel® Pentium(R) 4 CPU 2.40GHz Graphics VESA: Intel(r) 82945G Chipset Family Graphics OS type 32-bit glxgears output comes to be around 100fps which used to be around 900fps in Intrepid

  Read the article

• CRM: New Rollup Patches Released

  - by LuciaC

  See the table below for new rollup patches released for CRM family products. Product  Patch Number Reference Service Patch 17467506:R12.CS.B12.1.3:BUG FIXES FOR CS: OCTOBER'13 RUP PATCH n/a iStore Patch 16509570:R12.IBE.B- ORACLE ISTORE 12.1.3+ ROLLUP 1 Doc ID 1560963.1 Lease and Finance Management Patch 17485497:R12.OKL.B - OLFM : 1213 RUP3 DELTA 15 n/a For Trade Management and Price Protection the following Information Centers list the latest recommended patches and recently released patches: Critical, Recommended and Latest Patches for Oracle Trade Management (Doc ID 1569791.2) Critical, Recommended and Latest Patches for Oracle Price Protection (Doc ID 1305110.2)

  Read the article

• kernel warning disk error for command write - solaris svm

  - by help_me

  Recently this warning came up on my message logs, scsi: [ID 107833 kern.warning] WARNING: /pci@1c,600000/scsi@2/sd@0,0 (sd0): Oct 27 00:14:44 Error for Command: write(10) Error Level:Retryable Oct 27 00:14:44 scsi: [ID 107833 kern.notice] Requested Block: 101515828 Error Block: 101515828 Oct 27 00:14:44 scsi: [ID 107833 kern.notice] Vendor: SEAGATE Serial Number: 0441B9B5H Oct 27 00:14:44 scsi: [ID 107833 kern.notice] Sense Key: Hardware Error Oct 27 00:14:44 scsi: [ID 107833 kern.notice] ASC: 0x19 (defect list error), ASCQ: 0x0, FRU: 0x2 This is showing signs of disk failing in my opinion. I have not seen the messages re-occurring. This is on a Solaris 9 Sparc system V240. The disks are managed by SVM and "metadb" is showing the flags as "a" Are there any tests or indications as to check/see if the disk is actually failing or was that error message initiated by something else. Thank you!

  Read the article

• Inspiron 5720 unclaimed hardware

  - by Chelios

  I have two unclaimed devices in my Dell Inspiron 5720: *-display UNCLAIMED description: 3D controller product: NVIDIA Corporation vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress cap_list configuration: latency=0 resources: memory:f0000000-f0ffffff memory:c0000000-cfffffff memory:d0000000-d1ffffff ioport:3000(size=128) *-serial UNCLAIMED description: SMBus product: 7 Series/C210 Series Chipset Family SMBus Controller vendor: Intel Corporation physical id: 1f.3 bus info: pci@0000:00:1f.3 version: 04 width: 64 bits clock: 33MHz configuration: latency=0 resources: memory:f1614000-f16140ff ioport:efa0(size=32) What are these devices and what drivers do I need for them? Thanks!

  Read the article

• How to set the initial component focus

  - by frank.nimphius

  Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} In ADF Faces, you use the af:document tag's initialFocusId to define the initial component focus. For this, specify the id property value of the component that you want to put the initial focus on. Identifiers are relative to the component, and must account for NamingContainers. You can use a single colon to start the search from the root, or multiple colons to move up through the NamingContainers - "::" will pop out of the component's naming container and begin the search from there, ":::" will pop out of two naming containers and begin the search from there. Alternatively you can add the naming container IDs as a prefix to the component Id, e.g. nc1:nc2:comp1. http://download.oracle.com/docs/cd/E17904_01/apirefs.1111/e12419/tagdoc/af_document.html To set the initial focus to a component located in a page fragment that is exposed through an ADF region, keep in mind that ADF Faces regions - af:region - is a naming container too. To address an input text field with the id "it1" in an ADF region exposed by an af:region tag with the id r1, you use the following reference in af:document: <af:document id="d1" initialFocusId="r1:0:it1"> Note the "0" index in the client Id. Also, make sure the input text component has its clientComponent property set to true as otherwise no client component exist to put focus on.

  Read the article

• Install Base Transaction Error Troubleshooting

  - by LuciaC

  Oracle Installed Base is an item instance life cycle tracking application that facilitates enterprise-wide life cycle item management and tracking capability.In a typical process flow a sales order is created and shipped, this updates Inventory and creates a new item instance in Install Base (IB).  The Inventory update results in a record being placed in the SFM Event Queue.  If the record is successfully processed the IB tables are updated, if there is an error the record is placed in the csi_txn_errors table and the error needs to be resolved so that the IB instance can be created.It's extremely important to be proactive and monitor IB Transaction Errors regularly.  Errors cascade and can build up exponentially if not resolved. Due to this cascade effect, error records need to be considered as a whole and not individually; the root cause of any error needs to be resolved first and this may result in the subsequent errors resolving themselves. Install Base Transaction Error Diagnostic Program In the past the IBtxnerr.sql script was used to diagnose transaction errors, this is now replaced by an enhanced concurrent program version of the script. See the following note for details of how to download, install and run the concurrent program as well as details of how to interpret the results: Doc ID 1501025.1 - Install Base Transaction Error Diagnostic Program  The program provides comprehensive information about the errors found as well as links to known knowledge articles which can help to resolve the specific error. Troubleshooting Watch the replay of the 'EBS CRM: 11i and R12 Transaction Error Troubleshooting - an Overview' webcast or download the presentation PDF (go to Doc ID 1455786.1 and click on 'Archived 2011' tab).  The webcast and PDF include more information, including SQL statements that you can use to identify errors and their sources as well as recommended setup and troubleshooting tips. Refer to these notes for comprehensive information: Doc ID 1275326.1: E-Business Oracle Install Base Product Information Center Doc ID 1289858.1: Install Base Transaction Errors Master Repository Doc ID: 577978.1: Troubleshooting Install Base Errors in the Transaction Errors Processing Form  Don't forget your Install Base Community where you can ask questions to help you resolve your IB transaction errors.

  Read the article

• MySQL Cluster Failover doesn't work

  - by Lukasz

  I have two servers, where First server 10.100.15.150: 1. one mgm server 2. one ndbd 3. one mysql api Second server 10.100.15.160: 1. one ndbd 2. one mysql api When i start all 'parts' of cluster it looks : Cluster Configuration [ndbd(NDB)] 2 node(s) id=21 @10.100.15.150 (mysql-5.1.56 ndb-7.1.17, Nodegroup: 0) id=22 @10.100.15.160 (mysql-5.1.56 ndb-7.1.17, Nodegroup: 0, Master) [ndb_mgmd(MGM)] 1 node(s) id=3 @10.100.15.150 (mysql-5.1.56 ndb-7.1.17) [mysqld(API)] 2 node(s) id=11 @10.100.15.150 (mysql-5.1.56 ndb-7.1.17) id=12 @10.100.15.160 (mysql-5.1.56 ndb-7.1.17) When i shutdown first machine - 10.100.15.150, on second the nbdb process also has been shutdown so i cannot use this data node and cluster fail ... How i must configure this cluster to get FailOver working ? Thx

  Read the article

• Window 2003 Server - Logon Failure error message in Event Viewer

  - by user45192

  Hi guys, I received alot of event logged in the event viewer with this message. I notice is always the same user id which encounters this error. The user id is use by an application to access the database. However, this account does not exits on this server. How do I trace the services/program use by this user id which causes these error messages? Reason=Unknown user name or bad password&&User Name=&&Domain=&&Logon Type=3&&Logon Process=NtLmSsp&&Authentication Package=NTLM&&Workstation Name=&&Caller User Name=-&&Caller Domain=-&&Caller Logon ID=-&&Caller Process ID=-&&Transited Services=-&&Source Network Address=-&&Source Port=-&&User=SYSTEM&&ComputerName=

  Read the article

• ecommerce item deleted by user, 301 rediret to HOME PAGE or 404 not found?

  - by Marco Demaio

  I know this question is someway similar to this one where they reccomend using 404, but after reading this other one where they suggest to use 301 when changing site urls (in the specific case was due to redesign/refactoring) I get a bit of confused and I hope someone could clarify for this specific example: Let's say I have an ecommerce site, let's also say the final user inserted some interesting items in the site and the ecommerce webapp created the item pages at the urls: http://...?id=20, http://...?id=30 etc. Now let's say some of these interesting items got many external links toward them from many other sites because some people found those items very interesting and linked to them. After some years the final user deletes those items, so obviously the pages/urls http://...?id=20, http://...?id=30, etc. now do not exist anymore, but still many pages on the web are linking toward them. What should the ecommerce site do now, just show a 404 page for those items? But, I'm confused, wouldn't this loose all the Google PR passed by the external links to the items pages? So isn't it better to use 301 redirect to HOME PAGE that at least passes the PR to the HOME PAGE? Thanks, EDIT: Well, according to answeres the best thing to do so far is to do a 404/410. In order to make this question more complete, I would like to talk about a special case, just to make sure I understood. properly. Let's say the user creates those items again (the ones he previously deleted at point 4), maybe he changes a bit their names and description, but they are basically the same items. The webapp has no way to know these new added items were the old items so it obviously create them as new items with new urls http://...?id=100, http://...?id=101, does it makes sense at this point to redirect 301 the old urls to the new ones? MORE EDIT (It would be VERY IMPORTANT TO UNDERSTAND): Well according to the clever answers received so far it seems for the special case, explained in my last EDIT, I could use 301, since it's something of not deceptive cause basically the new pages is a replacement for the old page in term of contents. This is basically done to keep the PR passed from external link and also for better user experience. But beside the user experince, that is discussible (*1), in order to preserve PR from external broken linlks why not just always use 301, In my understanding Google dislikes duplicated contents, but are we sure that 301 redirect to HOME PAGE is seen as duplicated contents for Google?! Google itself suggests to redircet 301 index.html to document root so if they consider 301 as duplicated contents wouldn't that be considered duplicated contents too?! Why do they suggest it? Let me provoke you: “why not just add a 301 to HOME PAGE for every not found page?” (*1) as a user, when I follo a broken url from some external link to some website's page I would stick more on this website if I get redirected to HOME PAGE rather than seeing a 404 page where I would think the webiste does not even exist anymore and maybe I don't even try to go to HOME PAGE of the website.

  Read the article

• AppleTV - itunes store is temporarily unavailable - please check back later

  - by Ken

  When attempting to rent a movie on ATV, my wife received the error message above.  Alternately “server unavailable”.  When your wife is sick, the amount of IT support she needs goes up exponentially.  One piece of the puzzle was that she had changed her Apple ID password.  On her PC I ran iTunes and under account, there was only 1 device listed (not the ATV).  Even when signed out/back-in on the ATV under Settings>iTunes it still gave same error message.  What I suspect is it thinks she is trying to authorize the device to another Apple ID.  Some new 90 day rule limits when a device can be associated with another Apple ID.  Your iTunes store/account will show devices, and how long before they can be associated with a different Apple ID from the Account Information page in iTunes on your computer.  Apple must have no freaking idea why someone would want to know which ID is associated to the ATV (i.e. the vice versa), because it can’t be done. Solution: Try ATV settings>reset I swapped out ATV 1 for ATV 2 (used for music streaming downstairs).  I know it’s a cop-out solution, but remember I had a sick wife breathing down my neck.

  Read the article

• Consolidating hotels data from various booking sites with different IDs or reference

  - by Victor

  In one of my projects, I have data for hotels, and other booking sites are able to book this hotel. For example: Hotel A - Booking (ID = 4002), Expedia (ID = 123), Priceline (ID = 147) The three booking engines each uses their own Id to reference to Hotel A. I would need to check manually and make the right reference to the hotel. If I have 100,000 hotels, I have to check manually 300,000 (considering 3 booking sites) times? They might provide API, then I can cross check the name, address or latitude/longitude, but if they differ a little bit then I might give the wrong reference to the wrong hotel. I'm sure there are better ways to do this. There are many travel sites out there which do hotel price checking on many booking sites, but how do they do to make sure they are checking the right hotel on these booking sites? Anyone has any experience on this?

  Read the article

• Microsoft Lifecam VX-2000 doesn't work anymore in Cheese

  - by paed808

  I got have two Lifecam VX-2000's and they don't work in cheese anymore. I don't know if it's a problem with a missing package, or a package I installed. Here is the output. (cheese:11122): Clutter-WARNING **: No listener with the specified listener id 29 (cheese:11122): Clutter-WARNING **: No listener with the specified listener id 30 (cheese:11122): Clutter-WARNING **: No listener with the specified listener id 31 (cheese:11122): Clutter-WARNING **: No listener with the specified listener id 32 (cheese:11122): GLib-CRITICAL **: g_hash_table_remove_internal: assertion `hash_table != NULL' failed (cheese:11122): Clutter-WARNING **: Not able to remove listener with id 1 (cheese:11122): GLib-CRITICAL **: g_hash_table_size: assertion `hash_table != NULL' failed totem-video-thumbnailer: 'file:///home/myusername/Videos/Webcam/2012-09-20- 191530.webm' isn't thumbnailable Reason: Media contains no supported video streams. ** (cheese:11122): WARNING **: could not generate thumbnail for /home/myusername/Videos/Webcam/2012-09-20-191530.webm (video/webm) Notice the: Reason: Media contains no supported video streams. When I try to record a video it just makes a 13.2KB WEBM file with nothing. When I take a picture it works. Edit: I've been thinking that the problem started after installing the MediUbuntu repository on my system.

  Read the article

• Using static in PHP

  - by nischayn22

  I have a few functions in PHP that read data from functions in a class readUsername(int userId){ $reader = getReader(); return $reader->getname(userId); } readUserAddress(){ $reader = getReader(); return $reader->getaddress(userId); } All these make a call to getReader() { require_once("Reader.php"); static $reader = new Reader(); return $reader; } An overview of Reader class Reader{ getname(int id) { //if in-memory cache exists for this id return that //else get from db and cache it } getaddress(int id) { $this->getname(int id); //get address from name here } /*Other stuff*/ } Why is class Reader needed The Reader class does some in-memory caching of user details. So, I need only one object of class Reader and it will cache the user details instead of making multiple db calls. I am using static so that it the object gets created only once. Is this the right approach or should I do something else?

  Read the article

• How does Lastpass recognize actual login?

  - by Pan.student

  We are currently working on simple school project using Codeigniter where we need login page. It would be very useful if Lastpass could recognise and save logins. We have several accounts with different roles and manual insert of login is pretty slow. So I was wondering what needs to be done and where in files (view, controller?) for Lastpass to work as it does on every website. For example this is our login form: <?php echo form_open('login'); ?> <input type="text" id="username" name="username"/> <input type="text" id="password" name="password"/> <input type="submit" value="Login"/> </form> Thanks for help. (could not create new tag "Lastpass" due to low reputation) [SOLVED] changed <input type="text" id="password" name="password"/> to <input type="password" id="password" name="password"/>

  Read the article

• ThoughtWorks Gives Agile IT an Online Forum

  Vendor offers a new community for the discussion of issues surrounding agile development.

  Read the article

• ThoughtWorks Gives Agile IT an Online Forum

  Vendor offers a new community for the discussion of issues surrounding agile development.

  Read the article

• CommVault offers Cloud-Based Data Storage

  Storage management and backup software vendor CommVault is giving its Simpana software new cloud storage capabilities.

  Read the article

< Previous Page | 157 158 159 160 161 162 163 164 165 166 167 168  | Next Page >