Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 162/370 | < Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >

  • Lion MacBook Pro will not load webpages with DNS just after wake

    - by NReilingh
    I'm working with a 2011 MacBook Pro running Lion (10.7.2), that after waking from sleep (i.e. opening the lid) takes an inordinately long amount of time (2-3 minutes or more) to get a usable internet connection. Upon waking, the wi-fi icon signifies it is negotiating a network connection, and completes one a few seconds later. At this point, network diagnostics will not show any issues, and everything in Network preferences looks as normal: I'm connected to the proper network, have the right IP address and gateway, and DNS settings are correct. However, any site accessed with a domain name (like http://www.google.com) in Safari will return the "You are not connected to the Internet." error. Accessing a site directly, say, with Google's 74.125.226.212, is successful. Yet, Network Diagnostics will insist that DNS is functioning properly. After a few minutes, the following lines will be printed to the Console log, and regular behavior will be restored. 11/18/11 8:11:31.288 PM airportd: _doAutoJoin: Already associated to “Wireless”. Bailing on auto-join. 11/18/11 8:11:32.000 PM kernel: en1: BSSID changed to 00:25:9c:63:91:bd This behavior occurs only when waking from sleep--not when turning wi-fi on and off. This problem also occurs when using a wired Ethernet connection. As per this thread, I have tried flushing the DNS cache and wiping the wireless network from memory (it's not a protected network). Neither have worked.

    Read the article

  • Why doesn't Ubuntu show my wireless device after updating the kernel?

    - by Jigar Shah
    After an kernel update Ubuntu doesn't show my wireless device. How can I fix this? I checked the syslogs and it says the following: 2010-02-16 19:25:39,913 WARNING: /sys/module/wl/drivers does not exist, cannot rebind wl driver 2010-02-16 19:25:39,940 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted 2010-02-16 19:25:46,066 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted 2010-02-16 19:25:46,086 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted 2010-02-16 19:25:46,162 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted 2010-02-16 19:35:05,451 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted 2010-02-16 19:35:05,480 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted 2010-02-16 19:35:05,506 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted 2010-02-16 19:35:12,496 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted 2010-02-16 19:35:19,870 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted 2010-02-16 19:35:23,398 WARNING: modinfo for module wl failed: ERROR: modinfo: could not find module wl 2010-02-16 19:35:23,399 WARNING: /sys/module/wl/drivers does not exist, cannot rebind wl driver 2010-02-16 19:35:23,432 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted

    Read the article

  • Odd internet packet routing

    - by NachoChip
    I want to know is there anyway to explicitly control the packet routing. I try to connect my computer in HK from San Francisco. It is extremely slow and I use tracert to see what is going on. It seems the packet get routed from HK to Europe and then to New York and then to San Francisco. In US, I am using Astound Cable. Is there any suggestion I can force the packet to not go around the world before it reach my computer? Or it is all ISP dependent?

    Read the article

  • How do I network this Windows Failover Cluster and MongoDB Replica Set? (diagram inside)

    - by arex1337
    As you can see, my two Windows Server Failover Cluster (WSFC) nodes have three network interfaces each, which connects them to three different networks : A public network A private network consisting of the WSFC nodes A private network consisting of the WSFC nodes and a machine with the WSFC Quorum Witness File Share Does this network configuration I've planned, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. My two MongoDB Replica Set nodes also have three network interfaces each - very similar to the previous situation: A public network A private network consisting of the primary and secondary MongoDB Replica Set nodes A private network consisting of the primary, secondary and arbiter MongoDB Replica Set nodes Does this network configuration, make sense? Do I have the "right" number of NICs and networks? I'm thinking the 2nd NIC/network may be unnecessary. Here is the simpler version I'm considering: UPDATE:

    Read the article

  • Intel Centrino Advanced-N + WiMAX 6250 Drivers for Windows 8 (64 Bit) on Dell N7010

    - by kindrudekid
    I cannot seem to find or get the required drivers for Intel Centrino Advanced-N + WiMAX 6250 on windows 8 64bit on my Dell N7010 Laptop I have wifi connectivity but all i get is max G speeds and no N speeds, transfering files on mapped drives is really slow as a result, this wasnt the case before, i dont care about wimax, but even those drivers would be appreciated incase i decide to sell in future...

    Read the article

  • Openstack - Connectivity between instances on 2 separate nodes

    - by drcursor
    I have the following setup: 1 x Management Node (node A) 2 x Compute Nodes (node B & C) 1 x Volume Node (node D) Relevant configurations: VlanManager multi_host=true Node B[eth0=192.168.6.102;br100=10.1.0.6] Node C [eth0=192.168.6.103;br100=10.1.0.4] I can ping between instances on the same node,but not with instances in different nodes. If I run "brctl br100 eth0" , Instances can ping between nodes, but I loose conectivity on eth0 (192.168.6.102/192.168.6.103) What do I have to change to be able to ping instances between nodes while maintaining normal connectivity on eth0 ?

    Read the article

  • What are some good, IP Address Management solutions for IPv6? [closed]

    - by Russell Heilling
    There are a number of open source IPAM tools available for IPv4 address management; however there seems to be a distinct lack of actively updated tools available for IPv6. Other than FreeIPdb (code no longer maintained) or the RIPE Database (I have seen some customisations to the RIPEdb that allow for enterprise/ISP IPAM but it seems like overkill for a system that will probably only ever handle one /32 worth of space). Are there any other options that I'm missing? (Database only please. I know vi can be used for flat text IPAM, that's how I'm handling our /32 at the moment, but I don't see it scaling for much longer) It doesn't have to be open source but what are folks doing to manage IPv6 in a dual stack environment

    Read the article

  • Windows 8.1 killed my wifi

    - by char1es
    Was running Windows 8 on a Lenovo G780 and updated to windows 8.1 Wifi does not work anymore, i always receive a dns server not responding error. I have tried using public dns servers from Google but with still no results. I've restarted my router with no results. All other devices on my network are having no trouble at all. I've tried updating the wireless driver but the manufacturers website claims that the Win8.1 driver should be updated with the update from windows. So i cant find a wireless driver... Anyone else having this error and does anyone have any ideas on how to fix it?? EDIT: here are the driver details: Broadcom 802.11n Network Adapter Provider: Microsoft Driver Date: 2013-05-31 Driver Version: 6.30.223.102 Digital Signer: Microsoft Windows Thanks

    Read the article

  • Multiple virtual VLAN interfaces on single NIC (Debian)

    - by RayQuang
    I'm trying to setup multiple virtual interfaces with VLAN's on a single NIC. I'm running Debian Squeeze. Currently this is my /etc/netowrk/interfaces auto eth0.10 iface eth0.10 inet dhcp This gives me a working connection, however I'm not sure how to configure several like these on a single NIC so I can use multiple external IP's. I have tried aliasing the VLAN's like so: iface eth0.10:1 But that was not successful and it said failed to bring up interface. And suggestions would be greatly appreciated :)

    Read the article

  • How is DNS used by individual processes?

    - by atroon
    When resolving FQDNs or machine names to IP addresses on my local network (mycompany.internal) I can use dig on the command line (linux/mac) or nslookup (windows) to query the configured server and get a response. But trying to enter the FQDN or even just the machine name in a ping command or in a web browser results in 'Unknown Host' or DNS errors. Here's a sample, this one from the Mac: mac:~ atroon$ dig server.mycompany.internal ; <<>> DiG 9.6.0-APPLE-P2 <<>> server.mycompany.internal ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 5219 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.mycompany.internal. IN A ;; ANSWER SECTION: server.mycompany.internal. 1200 IN A 172.16.254.36 ;; Query time: 0 msec ;; SERVER: 172.16.254.8#53(172.16.254.8) ;; WHEN: Wed Dec 16 11:39:15 2009 ;; MSG SIZE rcvd: 55 mac:~ atroon$ ping server.mycompany.internal<br> ping: cannot resolve server.mycompany.internal: Unknown host I cannot for the life of me figure this one out. The DNS server is a SBS 2003 box which handles AD, some file/print, etc for a small company network. This issue happens to me about three times a week, and when I'm connected to the local network directly, the same switch as the server even. I can make any connection I want with IP addresses, I just can't make DNS work. Additionally, at the same time I'm experiencing this, other users are fine, which makes me think it's a problem on my Mac. But what sort of problem? How can dig send a query and get a reply, and ping say 'unknown host'? I'm posting here vs. serverfault because I think this is a local problem not a server problem...but if anyone can point me at the server, I guess we'll head down the street a domain or two.

    Read the article

  • How to connect Android phone to a Wifi network using PPPoE?

    - by Slavo
    I have an ISP at home, which provides me with a PPPoE connection. My router supports that and I've configured it to autoconnect periodically, so I don't have to type my username and password each time. When I connect to the Wireless router from the PC, I have internet and everything works fine. However, when I do so using my Android phone, there's no internet connection on the phone. It connects to the router, but I cannot open any web page. How can I enable internet access from such an ISP on my phone? Is it something in the router setup? The router is Linksys WRT54GL.

    Read the article

  • Why is network utilization so low

    - by dean20007
    My network utilization in windows never seems to get above 1%. This seems absolutely tiny, does anyone know why it is so low and if there is anyway to increase it(or if it indeed does need increased) FYI: I use a D-LINK USB wireless adaptor

    Read the article

  • How to create a separated network to customers only?

    - by Valter Henrique
    I work in a company where we have a network ethernet and wi-fi, we would like to create a network where our customers could access our network but don't have access to our computer network. This access would be internet only, nothing more. The customers will not see our computers and the files that we share in our network. I have two routers, how can I do this ? A Cisco Linksys Wireless-N Broadband Router WRT160N V3 and a Netgear Wireless G Router WGR614 v9 and about firewalls there´s only windows firewalls in each computer by default.

    Read the article

  • What is the simplest way to confirm or to disprove that Virtual Box virtual machines support GRE protocol

    - by mbaitoff
    It is stated in VirtualBox manual (chapter 6) that VM network interfaces in "NAT" mode do not support GRE protocol. I'm currently trying to setup a pair of VMs as pptp server and client which would communicate via VM's network interfaces in "INTERNAL NETWORK" mode. I set up modern Linux OSes with pptp software on both machines and made some basic pptp configuration. However, I fail to connect the client to the server - server reports a failure when writing to GRE socket. I now need a quick proof of principal ability to use the GRE protocol between VirtualBox VMs over a network in "INTERNAL" mode, such as a several-line .c program that would try to open/send/receive/close a GRE protocol connection, or like a specific lightweight tool to diagnose the GRE availability. Any suggestions?

    Read the article

  • Keep source IP after NAT

    - by John Miller
    Until today I used a cheapy router so I can share my internet connection and keep a webserver online too, while using NAT. Users IP ($_SERVER['REMOTE_ADDR']) was fine, I was seeing class A IPs of users. But as traffic grown up everyday, I had to install a Linux Server (Debian) to share my Internet Connection, because my old router couldn't keep the traffic anymore. I shared the internet via IPTABLES using NAT, but now, after forwarding port 80 to my webserver, now instead of seeing real users IP, I see my Gateway IP (Linux Internal IP) as any user IP Address. How to solve this issue? I edited my post, so I can paste the rules I'm currently using. #!/bin/sh #I made a script to set the rules #I flush everything here. iptables --flush iptables --table nat --flush iptables --delete-chain iptables --table nat --delete-chain iptables -F iptables -X # I drop everything as a general rule, but this is disabled under testing # iptables -P INPUT DROP # iptables -P OUTPUT DROP # these are the loopback rules iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # here I set the SSH port rules, so I can connect to my server iptables -A INPUT -p tcp --sport 513:65535 --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -p tcp --sport 22 --dport 513:65535 -m state --state ESTABLISHED -j ACCEPT # These are the forwards for 80 port iptables -t nat -A PREROUTING -p tcp -s 0/0 -d xx.xx.xx.xx --dport 80 -j DNAT --to 192.168.42.3:80 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p tcp -s 192.168.42.3 --sport 80 -j ACCEPT # These are the forwards for bind/dns iptables -t nat -A PREROUTING -p udp -s 0/0 -d xx.xx.xx.xx --dport 53 -j DNAT --to 192.168.42.3:53 iptables -t nat -A POSTROUTING -o eth0 -d xx.xx.xx.xx -j SNAT --to-source 192.168.42.3 iptables -A FORWARD -p udp -s 192.168.42.3 --sport 53 -j ACCEPT # And these are the rules so I can share my internet connection iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE iptables -A FORWARD -i eth0:1 -j ACCEPT If I delete the MASQUERADE part, I see my real IP while echoing it with PHP, but I don't have internet. How to do, to have internet and see my real IP while ports are forwarded too? ** xx.xx.xx.xx - is my public IP. I hid it for security reasons.

    Read the article

  • Hiding mapped drives for all users but letting programs access them

    - by AgainstClint
    What I'm looking for (and not sure if it's possible) is that we have 16 mapped network drives that are mapped when any user logs on, what I would like is to cut this down to just one visible drive yet leaving the other ones still usable to certain programs. I would just un-map them, however one of our constantly used programs writes to almost all of the drive letters so they need to be mapped for just that program, however they do not need to be visible to the user. Is this possible?

    Read the article

  • Wireless bridge between two prolink adsl modem/router

    - by MyName
    Allright, so i've got 2 prolink hurricane h5004n. Its a broadband adsl modem and router. My Pc is connected to the first one via ethernet. What i want to do is a wireless bridge to make the 2 routers "talk". I've tried hooking up the dsl cable (as they are modems) in both to try but when one disconnects as the other connects. I don't really know about the configurations to be done of all the DCHP or RIP and NAT forwarding stuffs. (i'm just writing what i saw) In short i want the second router to act as a wifi repeater but i don't see any repeater option and i also do not want to connect them via ethernet. So is it possible to do something? Apart from buying another repeater i don't want to spend anymore i'm done :S

    Read the article

  • Best way to troubleshoot intermittent network outages?

    - by Ben Scheirman
    We have a Comcast 50/10 line into our office. We keep seeing very short but sometimes frequent drops in our internet service. It's enough to kick you off of skype and stop any websites from loading, which is obviously affecting our productivity. We've tried 4 different routers, we've tried moving everyone off of wireless and onto wired via a switch and so far nothing has helped. Right now we're on a Cisco SB WRP400-G1 router. Attached to the router is a 16 port switch going to the ports in all of the offices. We've moved to OpenDNS in the case that it was the comcast DNS servers going down. Today we tried putting the modem, router, and switch on a UPS to make sure it wasn't power fluctuations that was causing it. Every time we call Comcast, by the time they are here the internet is working fine. I'd like to somehow prove that the problem is with Comcast, so if that means plugging in a machine directly into their router and collecting data all day, I'm up for that. I just want to hear ideas on what tools to run and how to collect this data. I could just continuously ping google.com all day long but I'm not sure how valuable that data would be. Thoughts?

    Read the article

  • How to reliably keep an SSH tunnel open?

    - by Peltier
    I use an SSH tunnel from work to go around various idotic firewalls (it's ok with my boss :)). The problem is, after a while the ssh connection usually hangs, and the tunnel is broken. If I could at least monitor the tunnel automatically, I could restart the tunnel when it hangs, but I haven't even figured a way of doing that. Bonus points for the one who can tell me how to prevent my ssh connection from hanging, of course!

    Read the article

  • How can I remotely display images on my computer?

    - by Jakob
    What I Have: A laptop booted with Ubuntu and a stationary computer dual-booted with Ubuntu and Vista, both connected through a wireless ad-hoc network. What I Want: I want a way to display images in fullscreen on my stationary, using my laptop as a "remote control". I want to be able to choose another picture at any time and have my stationary computer remain in fullscreen mode at all times. Preferably, I should also be able to display just an empty (black) screen. How can I arrange for this? What I Have Tried: I have tried simply SSH:ing into my stationary computer and opening the image files using an image viewer, but all of the ones that I have tried (Eye of Gnome, Mirage, Gwenview, and others) open a new window for every new image. I don't know how to force them into using a single instance. I have tried using the VLC remote control command line interface, but apart from seeming somewhat unreliable (exiting with segmentation faults at one point), it also displays some images with a green border and forces me to pause playback in order for the image to remain on screen. Bonus Question: In my final setup, I also need to play music through my stationary computer's speaker and have the ability to switch to another track at any point, like with the images. Preferably, I would like to control the images and the audio through the same interface. How can I best achieve this?

    Read the article

  • Stress test a server for simultaneous connection

    - by weston smith
    I am trying to figure out a practical way to stress test a server for 300 to 600 simultaneous connections. Any advice? Thank you everyone for the help. To be more specific (sorry I wasn't before) this is a Flash Media Server on AWS that will be streaming live video. I've been having problems with the video freezing/buffering for everyone and I need to verify if its on the user end, upload end, or server end. I mainly need help with stress testing the server with 300-600 multiple request before going live.

    Read the article

  • Setting up virtualbox for outside access

    - by Morgan Green
    I have a computer running a server that my subdomain on my shared hosting account points to. IE subdomain.mydomain.org goes to my home server. Now then; what I'm wanting to do is be able to access my VirtualBox servers through that subdomain and a different port. E.G Ubuntu Virtual Box Server 1 Username:Ubuntuhost1 Password:MyUbuntuHost1 Port:4000 Internal IP: 192.168.1.60 External IP: 24.29.138.45 Ubuntu Virtual Box Server 2 Username:UbuntuHost2 Password:MyUbuntuHost2 Port:4001 Internal IP: 192.168.1.61 External IP: 24.29.138.45 Now I want to be able to access RDP number 1 through Port 4000, but if I access Port 4001 it will connect to the server on port 4001; both using the same subdomain. The next issue is the fact that even though I know what the IP addresses are on the router for the virtualbox hosts through ifconfig it doesn't change the fact that they don't show up on the router. If anyone knows how to configure this to work please help me out because I've been racking my brain to the highest extent I can. Alright; here's an edit to clarify more; Sorry. My ports on the router are edited to forward Port 4000 on Internal IP 192.168.1.63 (My Ubuntu Internal IP address) Now when I go to my Router Home Page my VirtualBox Internal IP Address doesn't show on the attached device listings, so I set up port forwarding anyways to the VirtualBox Internal IP. My end goal is when I connect to mydomain.org and I connect through port 3389 it takes me to my host computers server, but if I put in mydomain.org and go through port 4000 it's going to redirect to my VirtualBox server; Is this even possible? Sorry; I'm trying to clarify the most I think I can I just don't know how else to explain my issue.

    Read the article

  • D-LINK DIR-615 router keeps giving my wireless devices bad ip addresses

    - by mlsteeves
    I have a D-LINK DIR-615 router, and wired devices have no problem getting an IP, however; wireless devices end up with a 169.254.. address (subsequently, they cannot access the internet through the router). I have removed all wired connections from the router, so there is no other dhcp server running. I've also gone back to the store, and replaced it with another, thinking that maybe it was defective. According to the router, it gave 192.168.0.101 to the wireless device. According to the wireless device it got 169.254.67.71. I've tried both a laptop and an iPod Touch, both exhibit the same behaviour. Has anyone seen this type of behaviour, or have any ideas of stuff to try? NEW INFORMATION I looked at the logs on the router, and when the wireless device tries to connect, this is what is logged: Sep 10 18:13:39 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:31 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:26 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:23 UDHCPD sending OFFER of 192.168.0.111 Sep 10 18:13:21 UDHCPD sending OFFER of 192.168.0.111 I connected a computer directly to the router, and here is what it looks like: Sep 10 18:14:18 UDHCPD Inform: add_lease 192.168.0.110 Sep 10 18:14:14 UDHCPD sending ACK to 192.168.0.110 Sep 10 18:14:14 UDHCPD sending OFFER of 192.168.0.110 Not sure if that helps or not.

    Read the article

  • Distribute outgoing connections among multiple IPs configured on the same NIC

    - by cedivad
    I have a NIC with 2 aliases on it. The network interface has 3 IPs configured on it. Think about it like this: i can ping the same server by hitting .100 .101 and .102. I want the source address of the outgoing connections to be distributed among these ip. So if i have 3 opened connections, one connection will have result as having an IP address ending with .100, the other two should result as having as ip addresses .101 and .102. I'm using FreeBSD but I think this question to be Linux-Like wide.

    Read the article

< Previous Page | 158 159 160 161 162 163 164 165 166 167 168 169  | Next Page >