Search Results

Search found 8715 results on 349 pages for 'bad sectors'.

Page 163/349 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

  • A website hosted on the 1.0.0.0/8 subnet, somewhere on the Internet?

    - by Dave Markle
    Background I'm attempting to demonstrate, using a real-world example, of why someone would not want to configure their internal network on the 1.0.0.0/8 subnet. Obviously it's because this is not designated as private address space. As of 2010, ARIN has apparently allocated 1.0.0.0/8 to APNIC (the Asia-Pacific NIC), who seems to have begun assigning addresses in that subnet, though not in 1.1.0.0/16, 1.0.0.0/16, and others (because these addresses are so polluted by bad network configurations all around the Internet). My Question My question is this: I'd like to find a website that responds on this subnet somewhere and use it as a counter-example, demonstrating to a non-technical user its inaccessibility from an internal network configured on 1.0.0.0/8. Other than writing a program to sniff all ~16 million hosts, looking for a response on port 80, does anyone know of a directory I can use, or even better yet, does anyone know of a site that's configured on this subnet? WHOIS seems to be too general of a search for me at this point...

    Read the article

  • Software that supports ATA Secure Erase Command

    - by vy32
    We have a lot of drives that need to be sanitized. NIST SP 800-88 recommends software that uses the ATA Secure Erase command. That's apparently the only way to be sure that the drive is properly wiped, due to bad-block remapping and such. I know that this functionality is available in hdparm. The problem with that approach is that it is inconsistent on multiple platforms, occasionally times out, doesn't have error-checking logic, and doesn't check the resulting drive to make sure that it has, in fact, been erased. So a proper program might use hdparm, but hdparm by itself isn't an answer. I'm looking for open source software that implements ATA Secure Erase. Ideally it will be a bootable disk image like DBAN, but it will use the ATA command.

    Read the article

  • Why would a machine ruin three "power supply"s?

    - by Moshe
    A client of mine has an XP era eMachines. The power supply has died and been replaced 3 times. I've discharged the motherboard and checked the surge protector. In the middle of a scan with ComboFix, the machine died. It powers on and hangs before the BIOS and shows a solid yellow light. I believe the model # is T5062 or something like that. Aside from a bad outlet, what would cause the PSU to die a few times?

    Read the article

  • Code deploy system [closed]

    - by Turnaev Evgeny
    Currently we deploy code to servers in a various ways: freebsd package freebsd ports part of config files and static just svn up'ed and a symlink is changed to new upped folder The distribution of freebsd packages to target servers is done through custom tool that uses ssh. I am looking for a code deploy system that will allow: deploy several packages (freebsd or linux) atomic (ether deploy all or none of them to server) can save a history of last stable version - so in case of bad deploy i can easily rollback to last working version all servers ease deployment of config and static files - and integrate those into atomic deploy/rollback system. should work with freebsd or linux (apt-get system)

    Read the article

  • Cannot do sudo: "/etc/sudoers is mode 0740, should be 0440"

    - by dehmann
    I have a problem: I don't have a root password on my mac. I just have an Admin account, which can do stuff using sudo. Now, I wanted to add my normal user to the /etc/sudoers file as well. Since it did not let me write to that file (even writing using sudo), I did this: sudo chmod u+w /etc/sudoers That worked. But since then I can't do any sudo command anymore on my system. It complains that /etc/sudoers has the wrong mode: $ sudo touch /etc/sudoers sudo: /etc/sudoers is mode 0740, should be 0440 Segmentation fault It sounds like a bad joke, because now I can't even change the mode back to 0440: $ sudo chmod 0440 /etc/sudoers sudo: /etc/sudoers is mode 0740, should be 0440 Segmentation fault Is there any way to fix this situation? I need to get my sudo abilities back.

    Read the article

  • notebook display problem

    - by kpower
    I have RoverScan Voyager notebook. It worked good for a few months. But some day I turned it on and saw that it displays badly. I mean, picture that should be displayed by monitor is copied six times and displayed on screen (6 same small pictures, not crossed each other). And the picture itself is bad - it displayed as interchange of vertical lines (it's really hard to see real picture or distinguish some details on it - it is distorted badly). Can you suppose, what's the reason? And what can I do to solve the problem?

    Read the article

  • How to remove line breaks (or carriage returns) only from certain parts of a block of text?

    - by Luke Allen
    Whenever I copy formatted text from a PDF file which is formatted to have line breaks (or carriage returns), I need to find a way to remove these line breaks without removing the paragraph format. To do this I need to use RegEx (Regular expressions) to only remove the line breaks which aren't preceded by a period. So for example, if a string of text has a line break right after a period, that is obviously almost always a legitimate line break which will start a new paragraph. If a string of text has a line break mid-word or after a word with no period, it's simply part of the bad formatting I need to get rid of. My problem is that I don't know how to use RegEx to make it only remove the ^p tags in word or CRLF or line breaks in any format under the conditions that it omits ones following a period.

    Read the article

  • Acrobat 8 on Windows 7 64-bit

    - by user66822
    Here's the situation I'm in. I have Acrobat 8 on Wows 7 (64-bit) and anytime I create PDFs any numbers on the page I'm PDFing come through as garbage. Everything else on the page comes out fine, just the numbers are messed up. They appear as random symbols. I've uninstalled, reinstalled. Applied all updates, not applied updates, nothing seems to help. Mayube I'm a bad searcher, can't put in the right search terms, but I can't find anything that seems to point me in a direction on this. ANy ideas?

    Read the article

  • Do virtual machines perform better on the host HDD or USB drive?

    - by Jeremy Ricketts
    The question I'm asking is kind of general, and I'll give more specifics about my specific setup. Here's the main question though: Do virtual machines generally perform better on the host HDD or is it better to operate them from an external disk? My specific setup: A Macbook Pro with a nearly full internal SATA drive that spins at 7200. On this system I'm running large programs like Photoshop and some other RAM-intense applications. I've dedicated 2 of my 8 gigs of RAM to my VMware Fusion virtual machine, which runs Windows 7 and Visual Studio, sits on the same drive. When that thing boots up, my system really starts crawling. I have an external USB (specifics of that drive are here) which I'm thinking about moving the VM to. Obviously a USB drive is slower than my internal HDD, but maybe having two operating systems using the same disk is WORSE than putting one of them on a separate (albiet slower) disk. This a bad idea?

    Read the article

  • How to Disable secondary drive from booting upon restart - Windows

    - by DevCompany
    I had a Windows 2003 Hard Drive on my server and it went bad so I installed a new clean hard drive and installed Windows 2008 R2 on the new clean drive. I moved the old 2003 drive to be used only for general storage on the same computer. It usually boots into Windows 2008 upon a restart, but just sometimes it starts trying to boot the old 2003 drive and causes boot issues(NTDLR Bootloader, and other errors), even though the order of boot preference is set to boot 2008, and NOT 2003. I need to know how to remove any old code that keeps this old drive as a bootable drive. I still want to use it as a secondary drive just dont want to have any boot code on it. hopefully my situation is clear for everyone to get a good response. Thank you...

    Read the article

  • Running NginX (with Apache) and cPanel/WHM

    - by ub3rst4r
    I was wondering if its a good idea to be running NginX as the webserver (on port 80) and Apache as the reverse proxy (on port 8080) with cPanel/WHM being used as a control panel? I also installed Nginx Admin so the configuration for NginX is managed by WHM. The reason I am asking is because I came across an article (http://kbeezie.com/view/apache-with-nginx/) which explains how to setup Apache as a reverse proxy but it states If you are using a control panel based hosting such as cpanel/whm, this method is not advised. Most of the servers configuration is handled automatically in those cases, and making manual changes will likely lead to problems (plus you won’t get support from the control panel makers or your hosting provider in most cases). Anyone have any past experiences with this and can say if its good/bad idea?

    Read the article

  • Lenovo t400 laptop docking station with DVI out shows green artifacts when connected to monitor

    - by Roy Rico
    I have a Lenovo T400 laptop, with Windows XP. I have a docking station connected via DVI to my Samnsung monitor. I'm connected at 1920x1200 resolution and I keep seeing all these green dots (when colors are supposed to be near black). It's really bad. I have tried running on my Samsung monitor, at all sizes, even down town 1280x1024 like my monitors at work. When I use the docking station at work, I am able to connect 2 1280x1024 NEC monitors (one via DVI, one through VGA, both through my docking station). I have absolutely no issue there, both displays work great. I have tried to update the drivers, I've even installed the latest video drivers from lenovo's site (DEC-02-2010). Is anyone familiar with this issue? Details: Docking Station: Lenovo Advanced Mini Dock- 250410U - NIB Montior at home: Samsung T240 24-inch monitor Monitors at work: NEC monitors

    Read the article

  • HP Laserjet "maintenance interval" vs "fuser life"

    - by marienbad
    I posted a question about the Laserjet 8100DN earlier here: http://serverfault.com/questions/139043/buying-an-old-laser-printer-what-will-need-to-be-replaced and from doing some more research I have a new question: I found the "maintence interval" -- "the interval at which you should install a maintenance kit" (which is a fuser and rollers), and it is...350,000 pages. BUT, when I look at the specs for an HP 8100 fuser, it says the fuser has a life span of 150,000 pages. What gives? – Will the fuser go bad after 150 or 350? ==== BTW I hope it's ok to ask another similar question in a new thread -- I'm just following instructions from my thread on the topic at Meta.

    Read the article

  • Graciously shutdown external HDD enclosure?

    - by Jakobud
    I recently purchased a large HDD along with the following HDD enclosure: http://www.newegg.com/Product/Product.aspx?Item=N82E16817173043 It has a simple on-off switch on the back. When I want to turn this thing off, do I simply just flip the switch? I assume the switch simply kills the power to the HDD, but isn't that potentially a bad thing in the case that the HDD is still reading/writing? I used to have a Seagate external HDD and it had a button on the front that I had to hold down for a second or two before it would turn off, but it at least appeared to sort of go through a shutdown procedure where it probably would stop the HDD activity before cutting power. So with this external HDD, I'm a little bit leery about that power switch and understanding exactly what it does. Is this how all HDD enclosures are? EDIT: I'm running the drive in Ubuntu Server. So there is no 'ejecting' the drive lol

    Read the article

  • Where are Credentials stored for Network Drives on WinXP?

    - by Tom Tresansky
    I have a drive mapped to a folder on a remote machine that I connect to using the Cisco VPN client. The password to the Windows account I use on that remote machine has changed. I had stored the username/password locally, using Window's remember my password feature, so I wouldn't have to enter it every time (the enter user/password login dialog used to appear each time I attempted to open the remote folder, and I would have to look up and enter my credentials). The password to that remote Windows account has changed. Now, I am no longer prompted to enter a user name / password, but instead, upon trying to open the remote folder, receive a message: unknown user name or bad password. How do I view and change these stored credentials?

    Read the article

  • Troubleshooting a crash with Windows 7

    - by AngryHacker
    I have a folder with several thousand videos (All .MPG extensions). When I open the folder with these videos, it shows up fine, but as I start scrolling down, it crashes the Windows Explorer. In the Event Viewer, I see this: Faulting application name: Explorer.EXE, version: 6.1.7600.16450, time stamp: 0x4aebab8d Faulting module name: ntdll.dll, version: 6.1.7600.16559, time stamp: 0x4ba9b802 Exception code: 0xc0000374 Fault offset: 0x00000000000c6df2 Faulting process id: 0x954 Faulting application start time: 0x01cbb1b71edf3b51 Faulting application path: C:\Windows\Explorer.EXE Faulting module path: C:\Windows\SYSTEM32\ntdll.dll Report Id: ee987372-1dc4-11e0-8e06-406186ea9135 I suspect that one of the videos has bad metadata. I removed the Length column and it was still crashing. I then removed the Date column and the problem disappeared. How do I go about troubleshooting this problem or at least identifying the file that's causing the issue.

    Read the article

  • Is there a way to correct wrongly typed password / abort the operation while on password prompt in the console in MINGW32?

    - by jakub.g
    I sometimes mistype a password when being asked for it, e.g. by Git when pushing to remote repository. The password is not displayed (even masked as asterisks) in the console. Is there a way either to correct the password, or to abort the operation? Backspace for editing and CtrlC for aborting do not seem to work. I want to save some time instead of waiting for the remote authentication to fail, or providing a bad password, then Enter, CtrlC. Edit: Unfortunately CtrlU doesn't work for me (MINGW32 @ Windows XP). Any other guesses?

    Read the article

  • MDADM RAID5 array showing as CLEAN FAULTY

    - by Dean Reilly
    A drive dropped out of my raid 5 array yesterday. It looks like the reason was due to a bad controller so I switched it out and attempted to re-add the drive but mdadm claimed it couldn't do it. So I zerod the superblock and just added the drive normally and left it to resync. When I came to check on the array this morning I was unable to mount it at all and it's now showing as CLEAN FAULTY with two drives missing. The two missing drives are listed as spare and faulty spare. Is there anything I can do in this situation or is the array gone?

    Read the article

  • Selling your iphone games. [closed]

    - by Artemix
    Hi. So, long story short, some days ago I pusblished an iPhone game, I think the game wasnt that bad tbh, and still I got only 10 sells at $0.99. Are they any publishers, sponsors, or distributors to make your game "visible" on the app store market?, or the only thing you need is to have an amazing game and thats all? Somehow I think that even if you have an awesome game if you dont do that "marketing magic" correctly you will not exist in the store. Now Im making a second game, completly different, and I want to know how to do things right. If anyone knows something about this topic, let me know. Thx in advance.

    Read the article

  • Un-balanced network speed although using fiberoptic cable line

    - by Hoàng Long
    I'm not sure this is a right place to ask this question, but there's a strange thing that I don't quite sure what the reason is. My company has hired a fiberoptic cable line for network use (Wifi and cable through a router). But the strange thing is that, whenever someone view YouTube or listen stream music, then network speed for all the others become extremely slow. The download speed for that person is about 4-5 MB/s (or more), but others suffer. I'm still a newbie about networking. But I know there should be a solution. Could anyone tell me a way to stop this bad behavior? It's not possible for asking people not viewing YouTube, since that's part of their jobs. Any insights about this problem would be very welcome.

    Read the article

  • WesternDigital SmartWare - still problematic?

    - by FrustratedWithFormsDesigner
    I've seen a lot of bad press on WD SmartWare (I think it comes on most WD backup devices now, such as their MyBook product line), mostly related to how it's impossible to remove properly or replace. There are allegations (I couldn't tell how true they were) that it has/is a rootkit, as well. Most of the articles are a couple of years old, so I'm wondering if SmartWare is still just as problematic as it was. Does it still have a nasty rootkit reputation and should I just stick with the Windows 7 built-in backup system, or is the current SmartWare generation improved and better behaved?

    Read the article

  • DNS settings for SaaS in the cloud?

    - by Jeremy
    I am building a SaaS product. When a user signs up for an account they must select an alias for their site --------.getlaunchpoint.com. Right now I have an A record *.getlaunchpoint.com that points to the ip address server. However, with Azure I am not given an IP address. The suggested implementation is to make use of a CNAME. I need to create a CNAME for *.getlaunchpoint.com - getlaunchpoint.cloudapp.net GoDaddy does not support CNAME wildcards. Searching on Google I'm getting conflicting information... is CNAME wildcard a bad practice? I run into the same problem with Amazon EC2 if I want to make use of load balancers because you cannot tie a public IP address to an Amazon Load Balancer. Amazon also suggests the use of a CNAME. Any help would be appreciated.

    Read the article

  • How much the distance and ms can affect on the download speed ?

    - by Prix
    Let's consider A (client) and B (server) where A makes download from B. How much can a bad routing from A to B affect the download speed ? For example A does a tracert to B and get a response of 10 steps where the avg ms is around 300 with 10% packet loss at the 4 step and when the connection is normal the avg from A to B is 10 ~ 30 ms. Could this sort of impact reduce A download speed drasticaly or as long as both side and routes have enough link for the full speed of A from B and vice-versa it should maintain the same speed ? Besides tracert and the ping analyse of A to B what else is used to identify the problem ? If you need extra information please let me know.

    Read the article

  • SQL Query fields change to uppercase on upload to server.

    - by Conor H
    Hi There, I have just finished developing an app using CodeIgniter. When I upload it to my Host (Hostgator shared) some of the SQL text is converted to uppercase and rendering the app unusable. In my database I have two tables client and transaction. When I upload the App to the server client and transaction is replaced with all caps. Obviously this is bad as MySQL queries are case sensitive. At first I was uploading with FTP and thought FTP was to blame. I then zipped up the app and uploaded the archive, unpacking it on the server shell. Still no joy. Any ideas on how to fix this? At the moment I just have to go into the server and edit my queries back to lowercase.. Cheers in advance for any ideas.. --Conor

    Read the article

  • How to rewrite to a virtual directory with a different application

    - by user42181
    Hi, I have a CMS application that manages multiple websites, today whenever i change the codebehind of one of these websites - i have to rebuild the dll for all websites, deploy it - this disconnects all current sessions and is really bad. The iis is configured to listen to all domain requests, if the request is to one of the websites' domain , the application rewrites it, or example, if someone requests for www.example.com, and example.com is configured in the application to be website 12, it is rewritten to www.example.com/websites/12/default.aspx. This is done for all websites. We want to seperate the dlls of the websites from each other, and from the main CMS, we have a virtual directory to each websites, but when trying to rewrite to it, we discover that IIS support this (we get an "Could not load type '_12._Default'". error). How can we perform this rewrite so it does rewrite to virtual directories, or if anyone has any other solution for the initial dll seperation problem. Thanks in advance

    Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >