Search Results

Search found 17744 results on 710 pages for 'target mode'.

Page 163/710 | < Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >

• Disk operations freeze Debian

  - by Grzenio

  Hi, I have just installed Debian testing on my new desktop and I am not very happy with performance - when I perform a disk intensive operation, e.g. upgrade packages in the system, everything seems to freeze, e.g. changing tabs in Iceweasel takes 3 seconds. I run the Debian on my 3 year old Thinkpad X60 ultra-portable, and I don't have these issues. (every single parameter of the laptop is much worse than the desktop). I am using the default packaged kernel and scripts. I run hdparm -t /dev/sda1 And I got around 96GB/s, which is expected. What else can I try to make it work better? EDIT: grzes:/home/ga# hdparm -i /dev/sda /dev/sda: Model=WDC WD15EARS-00Z5B1, FwRev=80.00A80, SerialNo=WD-WMAVU1362357 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq } RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50 BuffType=unknown, BuffSize=unknown, MaxMultSect=16, MultSect=16 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=2930277168 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio3 pio4 DMA modes: mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 udma2 udma3 udma4 udma5 *udma6 AdvancedPM=no WriteCache=enabled Drive conforms to: Unspecified: ATA/ATAPI-1,2,3,4,5,6,7 * signifies the current active mode EDIT2: Even my wife said "on this new computer I can't do anything when I copy the photos from the camera and its much worse than on the old one". So it must be serious. EDIT3: Updated to 2.6.32, but still no improvement EDIT4: I forgot to mention that the new disk is ext4, the old was ext3. EDIT5: Still not solved. I have a P43 ASUS P5QL-E board. Lines from dmesg that seem relevant: [ 0.370850] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.370852] io scheduler noop registered [ 0.370853] io scheduler anticipatory registered [ 0.370854] io scheduler deadline registered [ 0.370876] io scheduler cfq registered (default) ... [ 0.908233] ata_piix 0000:00:1f.2: version 2.13 [ 0.908243] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.908246] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 0.908275] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 0.908316] scsi0 : ata_piix [ 0.908374] scsi1 : ata_piix [ 0.909180] ata1: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 19 [ 0.909183] ata2: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 19 [ 0.909199] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.909202] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] [ 0.909228] ata_piix 0000:00:1f.5: setting latency timer to 64 [ 0.909279] scsi2 : ata_piix [ 0.909326] scsi3 : ata_piix [ 0.910021] ata3: SATA max UDMA/133 cmd 0xb000 ctl 0xac00 bmdma 0xa480 irq 19 [ 0.910024] ata4: SATA max UDMA/133 cmd 0xa880 ctl 0xa800 bmdma 0xa488 irq 19 [ 0.915575] FDC 0 is a post-1991 82077 ... [ 1.716062] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.716074] ata1.01: SATA link down (SStatus 0 SControl 300) [ 1.724318] ata1.00: ATA-8: WDC WD15EARS-00Z5B1, 80.00A80, max UDMA/133 [ 1.724322] ata1.00: 2930277168 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 1.740339] ata1.00: configured for UDMA/133 [ 1.740428] scsi 0:0:0:0: Direct-Access ATA WDC WD15EARS-00Z 80.0 PQ: 0 ANSI: 5 [ 1.746788] scsi 6:0:0:0: CD-ROM ASUS DRW-1608P 1.17 PQ: 0 ANSI: 5 ... [ 1.925981] sd 0:0:0:0: [sda] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) [ 1.926005] sd 0:0:0:0: [sda] Write Protect is off [ 1.926007] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.926020] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.926092] sda:sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray [ 1.931106] Uniform CD-ROM driver Revision: 3.20 [ 1.931191] sr 6:0:0:0: Attached scsi CD-ROM sr0 ... [ 1.941936] sda1 sda2 sda3 sda4 < sda5 sda6 > [ 1.967691] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.970938] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.970959] sr 6:0:0:0: Attached scsi generic sg1 type 5 ... [ 2.500086] EXT4-fs (sda3): mounted filesystem with ordered data mode ... [ 7.150468] EXT4-fs (sda6): mounted filesystem with ordered data mode

  Read the article

• Cannot connect to MySQL Server on RHEL 5.7

  - by Jeffrey Wong

  I have a standard MySQL Server running on Red hat 5.7. I have edited /etc/my.cnf to specify the bind address as my server's public IP address. [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql # Default to using old password format for compatibility with mysql 3.x # clients (those using the mysqlclient10 compatibility package). old_passwords=1 # Disabling symbolic-links is recommended to prevent assorted security risks ; # to do so, uncomment this line: # symbolic-links=0 [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid bind-address=171.67.88.25 port=3306 And I have also restarted my firewall sudo /sbin/iptables -A INPUT -i eth0 -p tcp --destination-port 3306 -j ACCEPT /sbin/service iptables save The network administrator has already opened port 3306 for this box. When connecting from a remote computer (running Ubuntu 10.10, server is running RHEL 5.7), I issue mysql -u jeffrey -p --host=171.67.88.25 --port=3306 --socket=/var/lib/mysql/mysql.sock but receive a ERROR 2003 (HY000): Can't connect to MySQL server on '171.67.88.25' (113). I've noticed that the socket file /var/lib/mysql/mysql.sock is blank. Should this be the case? UPDATE The result of netstat -an | grep 3306 tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN Result of sudo netstat -tulpen Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 127.0.0.1:2208 0.0.0.0:* LISTEN 0 7602 3168/hpiod tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 27 7827 3298/mysqld tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 0 5110 2802/portmap tcp 0 0 0.0.0.0:8787 0.0.0.0:* LISTEN 0 8431 3326/rserver tcp 0 0 0.0.0.0:915 0.0.0.0:* LISTEN 0 5312 2853/rpc.statd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 0 7655 3188/sshd tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 0 7688 3199/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 0 8025 3362/sendmail: acce tcp 0 0 127.0.0.1:2207 0.0.0.0:* LISTEN 0 7620 3173/python udp 0 0 0.0.0.0:909 0.0.0.0:* 0 5300 2853/rpc.statd udp 0 0 0.0.0.0:912 0.0.0.0:* 0 5309 2853/rpc.statd udp 0 0 0.0.0.0:68 0.0.0.0:* 0 4800 2598/dhclient udp 0 0 0.0.0.0:36177 0.0.0.0:* 70 8314 3476/avahi-daemon: udp 0 0 0.0.0.0:5353 0.0.0.0:* 70 8313 3476/avahi-daemon: udp 0 0 0.0.0.0:111 0.0.0.0:* 0 5109 2802/portmap udp 0 0 0.0.0.0:631 0.0.0.0:* 0 7691 3199/cupsd Result of sudo /sbin/iptables -L -v -n Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 6373 2110K RH-Firewall-1-INPUT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 RH-Firewall-1-INPUT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 1241 packets, 932K bytes) pkts bytes target prot opt in out source destination Chain RH-Firewall-1-INPUT (2 references) pkts bytes target prot opt in out source destination 572 861K ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 1 28 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 icmp type 255 0 0 ACCEPT esp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT ah -- * * 0.0.0.0/0 0.0.0.0/0 46 6457 ACCEPT udp -- * * 0.0.0.0/0 224.0.0.251 udp dpt:5353 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:631 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:631 782 157K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 120 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:443 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:23 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 4970 1086K REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Result of nmap -P0 -p3306 171.67.88.25 Host is up (0.027s latency). PORT STATE SERVICE 3306/tcp filtered mysql Nmap done: 1 IP address (1 host up) scanned in 0.09 seconds Solution When everything else fails, go GUI! system-config-securitylevel and add port 3306. All done!

  Read the article

• Outlook 2007 Does Not Accept Login Credentials, OWA Webmail Does. Troubleshooting Advice?

  - by Chris

  I am trying to connect Outlook 2007 to Exchange (Hosted Exchange from Rackspace). Soon, I will need to roll this out for our entire office. With the Exchange account added to Outlook, Outlook starts up and asks for the user's username and password. Unfortunately, it doesn't like the password I use for it. I can confirm this username (email address) and password combo works by using Outlook WebMail, and another user (in another network/office) confirmed the Exchange account does work within his Outlook client. In my network/office, I can confirm that an Outlook 2007 client (under Windows 7) can connect to the Hosted Exchange server from Rackspace. However, I have not been able to get Outlook 2007 (under Windows XP SP3) to connect to the very same Exchange server Outlook 2007 (under Windows 7) can connect to. Outlook continuously prompts me for the username and password and does not accept the correct combination. Now, regarding the Outlook client that cannot connect/login to Exchange: The user has full admin rights on the workstation We do not run a domain controller/LDAP The firewall on the workstation has been disabled Real time file scanning in Microsoft Security Essentials has been disabled There are no virus scanning applications that would interface with Outlook or an email server. The Exchange account is setup to run on a newly created Outlook profile The network firewall does not log any blocked attempts A packet capture at the router reveals communication between the workstation and the Exchange server or proxy (though, this is SSL encrypted, so I don't know what the computers are saying) I have applied a fix (Added DWORD value of 0 for DefConnectOpts under HKEY_CURRENT_USER\Software\Microsoft\Office\12.0\Outlook\RPC) that was recommended to make RPC function when the workstation does not have a default gateway set. Workstation is configured as DHCP. This fix did nothing, and it may be worth noting the RPC subkey was not present until I added it. RPC service is running on the workstation The program is not running under any compatibility mode. Side note: Outlook 2007 installs with compatibility mode for XP enabled by default in windows 7. Outlook 2007 will not even try to connect to exchange if this compatibility mode is checked. In windows xp, I tried checking compatibility mode for windows 2000, and was unable to connect to exchange as well. Here is the specific configuration I've used in a blank outlook profile: Microsoft Exchange Server: ##MASKED##-MBX-C18.mex07a.mlsrvr.com Username: (Full Email Address: [email protected]) Password: ##MASKED## Outlook Anywhere: Connect to Microsoft Exchange using HTTP Exchange Proxy Settings: Proxy Server: mex07a.emailsrvr.com Check "Connect using SSL only" Under "Only connect to proxy servers...", enter: msstd:mex07a.emailsrvr.com Check "On fast networks, connect using HTTP first, then connect using TCP/IP" Check "On slow networks, connect using HTTP first, then connect using TCP/IP" Proxy authentication settings: Basic Authentication Notes: mex07a.mlsrvr.com and mex07a.emailsrvr.com may look incorrect at first glance, but this is not a typo - these instructions were handed down from rackspace and are confirmed to be working, just not on this workstation. I have tried to use the RpcPing utility but must have been using it wrong. I got as far as "Bad Interface Descriptor". It would seem to me getting Outlook and Exchange to work together would be a breeze, especially since everything is done over port 80 with web services. Unfortunately, the user is stuck with WebMail access only, because Outlook won't accept the Exchange credentials. Do you have any ideas of other things I could try to debug this issue further? Any and all help is greatly appreciated. Thank you! -Chris

  Read the article

• ubuntu 10.04; kvm bridged networking not working with public ip addresses

  - by senorsmile

  I have a dedicated hosted server box with ubuntu 10.04 64 bit installed. I would like to run kvm with ubuntu 8.04 installed for some php 5.2 compatible apps(they don't work right with php 5.3, the default in ubuntu 10.04). I installed KVM as instructed at https://help.ubuntu.com/community/KVM/Installation . I installed the vm using virt-manager. I never could figure out how use virt-install or any of those automated installers. I just installed it using the disc. I set up bridged networking as per https://help.ubuntu.com/community/KVM/Networking . However, the bridged connection doesn't work. Here's my /etc/network/interfaces on the host, running ubuntu 10.04. (with specific public ip blanked) auto lo iface lo inet loopback auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address xx.xx.xx.xx netmask 255.255.255.248 gateway xx.xx.xx.xa bridge_ports eth0 bridge_stp on bridge_fd 0 bridge_maxwait 10 ` Here's my /etc/network/interfaces on the guest, running ubuntu 8.04. auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xy netmask 255.255.255.248 gateway xx.xx.xx.xa The two vm's can communicate to each other. But, the guest vm can't access anyone in the real world. Here's my /etc/libvirt/qemu/store_804.xml <domain type='kvm'> <name>store_804</name> <uuid>27acfb75-4f90-a34c-9a0b-70a6927ae84c</uuid> <memory>2097152</memory> <currentMemory>2097152</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/store_804.img'/> <target dev='hda' bus='ide'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> </disk> <interface type='bridge'> <mac address='52:54:00:26:0b:c6'/> <source bridge='br0'/> <model type='virtio'/> </interface> <console type='pty'> <target port='0'/> </console> <console type='pty'> <target port='0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes'/> <sound model='es1370'/> <video> <model type='cirrus' vram='9216' heads='1'/> </video> </devices> </domain> Any idea where I've gone wrong?

  Read the article

• Bonding: works only for download

  - by Crazy_Bash

  I would like to install bonding with 4 links with mode 4. but only "download/receiving" works with bondig. for transmitting the system chooses one link. ifconfig bond0 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 inet addr:ip Bcast:ip Mask:255.255.255.248 inet6 addr: fe80::92e2:baff:fe0f:76b4/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:239187413 errors:0 dropped:10944 overruns:0 frame:0 TX packets:536902370 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14688536197 (13.6 GiB) TX bytes:799521192901 (744.6 GiB) eth2 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:54969488 errors:0 dropped:0 overruns:0 frame:0 TX packets:2537 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3374778591 (3.1 GiB) TX bytes:314290 (306.9 KiB) eth3 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:64935805 errors:0 dropped:1 overruns:0 frame:0 TX packets:2532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3993499746 (3.7 GiB) TX bytes:313968 (306.6 KiB) eth4 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:57352105 errors:0 dropped:2 overruns:0 frame:0 TX packets:536894778 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3524236530 (3.2 GiB) TX bytes:799520265627 (744.6 GiB) eth5 Link encap:Ethernet HWaddr 90:E2:BA:0F:76:B4 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:61930025 errors:0 dropped:3 overruns:0 frame:0 TX packets:2540 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3796021948 (3.5 GiB) TX bytes:314274 (306.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:62 errors:0 dropped:0 overruns:0 frame:0 TX packets:62 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:5320 (5.1 KiB) TX bytes:5320 (5.1 KiB) those are my configs: DEVICE="eth2" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth3" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth4" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE="eth5" BOOTPROTO="none" MASTER=bond0 SLAVE=yes USERCTL=no NM_CONTROLLED="no" ONBOOT="yes" DEVICE=bond0 IPADDR=<ip> BROADCAST=<ip> NETWORK=<ip> GATEWAY=<ip> NETMASK=<ip> USERCTL=no BOOTPROTO=none ONBOOT=yes NM_CONTROLLED=no cat /proc/net/bonding/bond0 Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Bonding Mode: IEEE 802.3ad Dynamic link aggregation Transmit Hash Policy: layer2 (0) MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 802.3ad info LACP rate: slow Aggregator selection policy (ad_select): stable Active Aggregator Info: Aggregator ID: 1 Number of ports: 4 Actor Key: 17 Partner Key: 11 Partner Mac Address: 00:24:51:12:63:00 Slave Interface: eth2 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b4 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth3 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b5 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth4 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b6 Aggregator ID: 1 Slave queue ID: 0 Slave Interface: eth5 MII Status: up Speed: 1000 Mbps Duplex: full Link Failure Count: 0 Permanent HW addr: 90:e2:ba:0f:76:b7 Aggregator ID: 1 Slave queue ID: 0 /etc/modprobe.d/bonding.conf alias bond0 bonding options bond0 mode=4 miimon=100 updelay=200 #downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 Linux: Linux 3.0.0+ #1 SMP Fri Oct 26 07:55:47 EEST 2012 x86_64 x86_64 x86_64 GNU/Linux what i've tried: downdelay=200 xmit_hash_policy=layer3+4 lacp_rate=1 mode 6

  Read the article

• Centos 7. Freeradius fails to start on boot

  - by Alex

  I was messing around with FreeRADIUS and MySQL (MariaDB) and it seems FreeRADIUS service can't start properly on startup. But it starts fine using root user or in debug mode (radiusd -X) and works just fine! Debug mode shows no errors. systemctl command shows that radiusd.service has failed to start. /var/log/messages output: Aug 21 15:52:29 nexus-test systemd: Starting The Apache HTTP Server... Aug 21 15:52:29 nexus-test systemd: Starting MariaDB database server... Aug 21 15:52:29 nexus-test systemd: Starting FreeRADIUS high performance RADIUS server.... Aug 21 15:52:29 nexus-test systemd: Started OpenSSH server daemon. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Logging to '/var/log/mariadb/mariadb.log'. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql Aug 21 15:52:30 nexus-test systemd: Started Postfix Mail Transport Agent. Aug 21 15:52:30 nexus-test avahi-daemon[604]: Registering new address record for fe80::250:56ff:fe85:e4af on eth0.*. Aug 21 15:52:30 nexus-test systemd: radiusd.service: control process exited, code=exited status=1 Aug 21 15:52:30 nexus-test systemd: Failed to start FreeRADIUS high performance RADIUS server.. Aug 21 15:52:30 nexus-test systemd: Unit radiusd.service entered failed state. Aug 21 15:52:31 nexus-test kdumpctl: kexec: loaded kdump kernel Aug 21 15:52:31 nexus-test kdumpctl: Starting kdump: [OK] Aug 21 15:52:31 nexus-test systemd: Started Crash recovery kernel arming. Aug 21 15:52:31 nexus-test systemd: Started The Apache HTTP Server. Aug 21 15:52:31 nexus-test systemd: Started MariaDB database server. /var/log/radius/radius.log output: Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Driver rlm_sql_mysql (module rlm_sql_mysql) loaded and linked Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Attempting to connect to database "radius" Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Opening additional connection (0) Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Couldn't connect socket to MySQL server radius@localhost:radius Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Mysql error 'Can't connect to local MySQL server through socket '/var/lib/mysql/mysql.sock' (2)' Thu Aug 21 15:24:16 2014 : Error: rlm_sql (sql): Opening connection failed (0) Thu Aug 21 15:24:16 2014 : Error: /etc/raddb/mods-enabled/sql[47]: Instantiation failed for module "sql" After seeing this I tried to replicate the problem, killed mariadb.service and started to run debug mode again. And it spits out the same problem as in the radius.log. I tried disabling iptables and firewalld and rebooting, but no luck: systemctl disable iptables systemctl disable firewalld So maybe the problem is in the process startup order or delay of some kind. Maybe FreeRADIUS's SQL module can't connect to not yet started MariaDB? If it, how can I fix this? In earlier versions of RHEL/CENTOS I know you easily see service start order in like rc.d or stuff, now IDK. I am new to this fancy "systemd", "systemctl", "firewalld" stuff Centos 7 introduced so sorry I'm a little bit confused. Also this new FreeRADIUS 3 structure... PS. MariaDB is enabled on startup, credentials in FR DB configuration are correct A little update: cat /etc/systemd/system/multi-user.target.wants/radiusd.service output: [Unit] Description=FreeRADIUS high performance RADIUS server. After=syslog.target network.target [Service] Type=forking PIDFile=/var/run/radiusd/radiusd.pid ExecStartPre=-/bin/chown -R radiusd.radiusd /var/run/radiusd ExecStartPre=/usr/sbin/radiusd -C ExecStart=/usr/sbin/radiusd -d /etc/raddb ExecReload=/usr/sbin/radiusd -C ExecReload=/bin/kill -HUP $MAINPID [Install] WantedBy=multi-user.target

  Read the article

• FTP Upload works from local command line / remote GUI client but not from PHP script

  - by MrOodles

  I originally posted this question at StackOverflow, but I'm beginning to think it's more of a server question. I have installed ProFTPd on an EC2 instance running Ubuntu 10.10. I have managed my proftpd.conf file as well as my server permissions to be able to connect and upload/move files using FTP both remotely using Filezilla, and on the server itself when connecting to 127.0.0.1. The problem I'm running into is when I try to upload/install a file using Joomla's interface. I give Joomla the same login information that I give to Filezilla, and the connection is made in the same fashion. The ftp.log file actually shows that Joomla is able to login to the server: localhost UNKNOWN nobody [17/Jan/2011:14:09:17 +0000] "USER ftpuser" 331 - localhost UNKNOWN ftpuser [17/Jan/2011:14:09:17 +0000] "PASS (hidden)" 230 - localhost UNKNOWN ftpuser [17/Jan/2011:14:09:17 +0000] "PASV" 227 - localhost UNKNOWN ftpuser [17/Jan/2011:14:09:17 +0000] "TYPE I" 200 - localhost UNKNOWN ftpuser [17/Jan/2011:14:09:17 +0000] "STOR /directory/store/location/file.zip" 550 - But it fails when attempting the STOR command. I have traced the problem in the Joomla code to the PHP FTP module. The code (with my trace statements added): if (@ftp_put($this->_conn, $remote, $local, $mode) === false) { echo "\n FTP PUT failed."; echo "\n Remote: $remote ; Local: $local ; Mode: $mode - Either ASCII: ".FTP_ASCII." or Binary: ".FTP_BINARY; echo "\n The user: ".exec("whoami"); JError::raiseWarning('35', 'JFTP::store: Bad response' ); return false; } Trace ouputs: FTP PUT failed. Remote: /directory/store/location/file.zip ; Local: /tmp/phpwuccp4 ; Mode: 2 - Either ASCII: 1 or Binary: 2 The user: www-data And in case you were curious, here is an example of the FTP log when using Filezilla: my_client_ip UNKNOWN nobody [17/Jan/2011:16:45:55 +0000] "USER ftpuser" 331 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "PASS (hidden)" 230 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "OPTS UTF8 ON" - - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "PWD" 257 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "TYPE I" 200 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "PASV" 227 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:45:55 +0000] "MLSD" 226 3405 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:06 +0000] "CWD location" 250 3405 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:06 +0000] "PWD" 257 3405 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:06 +0000] "PASV" 227 3405 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:07 +0000] "MLSD" 226 3757 my_client_ip UNKNOWN nobody [17/Jan/2011:16:46:37 +0000] "USER ftpuser" 331 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "PASS (hidden)" 230 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "OPTS UTF8 ON" - - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "CWD /location" 250 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "PWD" 257 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "TYPE I" 200 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:37 +0000] "PASV" 227 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:39 +0000] "STOR file.zip" 226 125317 my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:39 +0000] "PASV" 227 - my_client_ip UNKNOWN ftpuser [17/Jan/2011:16:46:39 +0000] "MLSD" 226 497

  Read the article

• cannot send mail to postfix /w iptables linux proxy

  - by Juzzam

  I have two separate servers, both running Ubuntu 8.04. Server 1 has the real domain name of our site, let's refer to it as example.com. Server 2 is a mail server I have setup with postfix/courier. The hostname for this server is mail.example.com. I've setup iptables on Server 1 to forward all traffic on port 25 to Server 2. I used this script (except I changed the target ip address and the port from 80 to 25). When I send an email to [email protected] it works. However, when I try to send an email to [email protected] from gmail, I get this error: 550 550 #5.1.0 Address rejected [email protected] (state 14) /var/log/mail.log shows no new lines when this happens. What is strange is that it works with telnet from my local machine. For example: $ telnet example.com 25 220 VO13421.localdomain SMTP Postfix EHLO example.com 250-VO13421.localdomain 250-PIPELINING 250-SIZE 10240000 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN MAIL FROM: [email protected] 250 2.1.0 Ok RCPT TO: [email protected] 250 2.1.5 Ok data 354 Please start mail input. hello user... how have you been? . 250 Mail queued for delivery. quit 221 Closing connection. Good bye. /var/log/mail.log shows success (and the email goes to the maildr): Feb 24 09:47:36 VO13421 postfix/smtpd[2212]: connect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: 65C68120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: 6BDFA120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/cleanup[2216]: 6BDFA120321: message-id= Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: from=, size=395, nrcpt=1 (queue active) Feb 24 09:48:29 VO13421 postfix/virtual[2217]: 6BDFA120321: to=, relay=virtual, delay=0.28, delays=0.25/0.02/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: removed Feb 24 09:48:30 VO13421 postfix/smtpd[2212]: disconnect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] iptables -L -n -v --line on example.com yields the following. Anyone know an iptables command to see the port forwarding? Also, it seems to accept all traffic, that's probably bad right? ;] num pkts bytes target prot opt in out source destination 1 14041 1023K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 338 20722 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 419K packets, 425M bytes) num pkts bytes target prot opt in out source destination 1 13711 2824K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 postconf -n results in: alias_database = hash:/etc/postfix/aliases alias_maps = hash:/etc/postfix/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix delay_warning_time = 4h disable_vrfy_command = yes inet_interfaces = all local_recipient_maps = mailbox_size_limit = 0 masquerade_domains = mail.example.com mail1.example.com masquerade_exceptions = root maximal_backoff_time = 8000s maximal_queue_lifetime = 7d minimal_backoff_time = 1000s mydestination = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mynetworks_style = host myorigin = example.com readme_directory = no recipient_delimiter = + relayhost = smtp_helo_timeout = 60s smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname SMTP $mail_name smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org smtpd_delay_reject = yes smtpd_hard_error_limit = 12 smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_limit = 16 smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_data_restrictions = reject_unauth_pipelining smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit smtpd_soft_error_limit = 3 smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes unknown_local_recipient_reject_code = 450 virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf virtual_gid_maps = mysql:/etc/postfix/mysql_gid.cf virtual_mailbox_base = /var/spool/mail/virtual virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf virtual_uid_maps = mysql:/etc/postfix/mysql_uid.cf

  Read the article

• MPLS basic configuration

  - by Vineet Menon

  I want to test out MPLS VPN in my lab. I have 3 routers. 2 PEs and 1P router, all cisco 2921. Something like this, ----- ---- ----- | PE1 |.1____192.168.1.0____.2| P |.2____192.168.2.0____.1| PE2 | | | | | | | ----- ---- ----- lo0:10.1.1.1 lo0:10.1.1.2 lo0:10.1.1.3 Here's the configuration file for each of them, PE1 router hostname PE1 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! interface Loopback0 ip address 10.1.1.1 255.255.255.255 ! interface GigabitEthernet0/0 ip address 192.168.1.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.1.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.1 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.3 remote-as 100 neighbor 10.1.1.3 update-source Loopback0 neighbor 172.16.1.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.3 activate neighbor 10.1.1.3 send-community extended exit-address-family For P router: hostname P ! no ipv6 cef ip source-route ip cef ! interface Loopback0 ip address 10.1.1.2 255.255.255.255 ! interface GigabitEthernet0/1 ip address 192.168.1.2 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/2 ip address 192.168.2.2 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.2 0.0.0.0 area 0 network 192.168.1.0 0.0.0.255 area 0 network 192.168.2.0 0.0.0.255 area 0 ! For PE2 router: ! hostname PE2 ! no ipv6 cef ip source-route ip cef ! ! ! ip vrf cust1 rd 100:100 route-target export 100:100 route-target import 100:100 ! ! ! interface Loopback0 ip address 10.1.1.3 255.255.255.0 ! interface GigabitEthernet0/0 ip address 192.168.2.1 255.255.255.0 duplex auto speed auto ! interface GigabitEthernet0/1 ip vrf forwarding cust1 ip address 172.16.2.1 255.255.255.0 duplex auto speed auto ! router ospf 1 network 10.1.1.3 0.0.0.0 area 0 network 192.168.2.0 0.0.0.255 area 0 ! router bgp 100 bgp log-neighbor-changes neighbor 10.1.1.1 remote-as 100 neighbor 10.1.1.1 update-source Loopback0 neighbor 172.16.2.2 remote-as 65001 ! address-family vpnv4 neighbor 10.1.1.1 activate neighbor 10.1.1.1 send-community extended exit-address-family ! I am following this article form cisco. But things are not working properly. Any help would be appreciated.

  Read the article

• cannot send mail to postfix /w iptables linux proxy

  - by Juzzam

  I have two separate servers, both running Ubuntu 8.04. Server 1 has the real domain name of our site, let's refer to it as example.com. Server 2 is a mail server I have setup with postfix/courier. The hostname for this server is mail.example.com. I've setup iptables on Server 1 to forward all traffic on port 25 to Server 2. I used this script (except I changed the target ip address and the port from 80 to 25). When I send an email to [email protected] it works. However, when I try to send an email to [email protected] from gmail, I get this error: 550 550 #5.1.0 Address rejected [email protected] (state 14) /var/log/mail.log shows no new lines when this happens. What is strange is that it works with telnet from my local machine. For example: $ telnet example.com 25 220 VO13421.localdomain SMTP Postfix EHLO example.com 250-VO13421.localdomain 250-PIPELINING 250-SIZE 10240000 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN MAIL FROM: [email protected] 250 2.1.0 Ok RCPT TO: [email protected] 250 2.1.5 Ok data 354 Please start mail input. hello user... how have you been? . 250 Mail queued for delivery. quit 221 Closing connection. Good bye. /var/log/mail.log shows success (and the email goes to the maildr): Feb 24 09:47:36 VO13421 postfix/smtpd[2212]: connect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: 65C68120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: 6BDFA120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/cleanup[2216]: 6BDFA120321: message-id= Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: from=, size=395, nrcpt=1 (queue active) Feb 24 09:48:29 VO13421 postfix/virtual[2217]: 6BDFA120321: to=, relay=virtual, delay=0.28, delays=0.25/0.02/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: removed Feb 24 09:48:30 VO13421 postfix/smtpd[2212]: disconnect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] iptables -L -n -v --line on example.com yields the following. Anyone know an iptables command to see the port forwarding? Also, it seems to accept all traffic, that's probably bad right? ;] num pkts bytes target prot opt in out source destination 1 14041 1023K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 338 20722 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 419K packets, 425M bytes) num pkts bytes target prot opt in out source destination 1 13711 2824K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 postconf -n results in: alias_database = hash:/etc/postfix/aliases alias_maps = hash:/etc/postfix/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix delay_warning_time = 4h disable_vrfy_command = yes inet_interfaces = all local_recipient_maps = mailbox_size_limit = 0 masquerade_domains = mail.example.com mail1.example.com masquerade_exceptions = root maximal_backoff_time = 8000s maximal_queue_lifetime = 7d minimal_backoff_time = 1000s mydestination = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mynetworks_style = host myorigin = example.com readme_directory = no recipient_delimiter = + relayhost = smtp_helo_timeout = 60s smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname SMTP $mail_name smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org smtpd_delay_reject = yes smtpd_hard_error_limit = 12 smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_limit = 16 smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_data_restrictions = reject_unauth_pipelining smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit smtpd_soft_error_limit = 3 smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes unknown_local_recipient_reject_code = 450 virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf virtual_gid_maps = mysql:/etc/postfix/mysql_gid.cf virtual_mailbox_base = /var/spool/mail/virtual virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf virtual_uid_maps = mysql:/etc/postfix/mysql_uid.cf

  Read the article

• ISP 5 Device Limit ... again

  - by Tommo

  Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

  Read the article

• "ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver" wheel-click is wrong

  - by sputnick

  I use this mouse under archlinux x86_64 with 3.2.8-1-ARCH kernel. I have some problems to select and then paste with the wheel-click in some applications like konversation, not in a terminal nor an editor. I don't know if it's a hardware problem or a software one. $ lsusb -v Bus 002 Device 110: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x046d Logitech, Inc. idProduct 0xc50e Cordless Mouse Receiver bcdDevice 25.10 iManufacturer 1 Logitech iProduct 2 USB RECEIVER iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 34 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 70mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.11 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 95 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) When I see what's happens in xev, the output is different compared to another mouse My buggy Logitech mouse : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350700, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350700, (48,52), root:(1491,75), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 16 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350988, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350988, (48,52), root:(1491,75), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 a working mouse (dell) : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245131, (46,32), root:(1489,55), state 0x10, button 2, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245131, (46,32), root:(1489,55), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 528 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245411, (46,32), root:(1489,55), state 0x210, button 2, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245411, (46,32), root:(1489,55), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 A demo of the problem when I use konversation (IRC) : http://www.youtube.com/watch?v=lhmr92M7NCc I tried to modify the button map with xmodmap like this with no success (one at a time) : xmodmap -e "pointer = 1 0 3" xmodmap -e "pointer = 1 1 3" xmodmap -e "pointer = 1 2 3" xmodmap -e "pointer = 1 3 3" xmodmap -e "pointer = 1 4 3" xmodmap -e "pointer = 1 5 3" xmodmap -e "pointer = 1 6 3" xmodmap -e "pointer = 1 7 3" xmodmap -e "pointer = 1 8 3" xmodmap -e "pointer = 1 9 3" xmodmap -e "pointer = 1 10 3" xmodmap -e "pointer = 1 11 3" xmodmap -e "pointer = 1 12 3" xmodmap -e "pointer = 1 13 3" xmodmap -e "pointer = 1 14 3" xmodmap -e "pointer = 1 15 3" xmodmap -e "pointer = 1 16 3" xmodmap -e "pointer = 1 17 3" xmodmap -e "pointer = 1 18 3" xmodmap -e "pointer = 1 19 3" xmodmap -e "pointer = 1 20 3" xmodmap -e "pointer = 1 21 3" xmodmap -e "pointer = 1 22 3" xmodmap -e "pointer = 1 23 3" xmodmap -e "pointer = 1 24 3" xmodmap -e "pointer = 1 25 3" Any clue ? I would like to avoid buying a new mouse just for a paste problem.

  Read the article

• Hosed Windows 7 permissons

  - by Anthony

  Here is the most interesting thing I've noticed since the problems started: If I go into a control panel/system module (in this case the Resource Monitor) that has a "Check Online" type option, Firefox (my default browser) opens right up without a problem. But if I just start Firefox from any shortcuts (start menu, desktop, etc), the Firefox process starts up (and the start menu icon starts glowing) only to end without notice a few seconds later. Possibly related: If I start up in Safe-Mode (w/o Networking, but haven't tried with yet), I can start up FF or Chrome just fine, but if I attempt to open Chrome normally, I get a permissions error. Opera and Safari seem to be okay (mostly). Safari crashes when I try to download any files. All of the above leads me to believe that some (but clearly not all) core files have messed up permissions. Or rather, that I no longer have permission. System still does, based on Firefox opening without fail when the system initiates it. I've run MS Forefront once in normal mode, Malwarebytes twice in normal mode and once in safe-mode. One trojan found and deleted, but the problem persists. Two other things worth mentioning: I accidentally duplicated my library... I thought I'd try to add the "Internet" folder to my start menu, next to music and downloads. The first advanced thing I tried was "create new library". I clearly misunderstood what this means. I thought it was a way to add virtual folders to the library (which I thought, in turn, would allow me to choose it as a link on the start menu), but instead it recreated my already existing user folder, AppData and all. I didn't notice this until today. Then I tried setting permissions for my User folder to full control, recursively... Confused but not giving up,I thought I could maybe create a shortcut to the NetHood folder manually, but instead got hit with an access denied error. So I tried to change the permission levels for all sub-folders to my user folder so that I had full control. I got several access denied errors along the way. At this point I gave up, went out, ended up caught in the rain and stuck on a friend's couch and showing up late for work the next day. Thanks for nothing, Microsoft. When I finally got home today (20 hours later), I noticed that Firefox was acting really strange. I tried opening Chrome to see if the problem was client side or server side, and instead got the above-mentioned "you don't have permission to open this program" alert. And I think that's the whole story. Oh, I also did a system restore, but not chose a point from this morning (an auto update), and it worked but the problem wasn't fixed. And then all the earlier restore points were gone. So the questions are: a) is there a way to set the admin and user privs back to "default"? b) would this, in anyone's expert opinion, fix the problems I'm having? c) how come being logged in as an admin isn't the same as being logged in with admin privs? It seems that half the time I have to do run as admin for fairy standard things because i'm being treated as me-theuser and not me-theadmin. Thanks for reading.

  Read the article

• Windows 7 is stuck at "Starting Windows" when I attempt to boot computer

  - by Eli

  Basically, whenever I turn on my computer, it gets to the Starting Windows phase and just stays there. The startup animation still plays, yet it gets nowhere. I have tried booting into safe mode, however it gets stuck at loading CLASSPNP.SYS. It then freezes there and doesn't continue booting. I have tried booting into recovery mode from the hard drive, and it freezes after displaying the background image. I have tried booting from a recovery CD, which works, and I was able to use system restore. However, using system restore did not fix it, and it still is stuck at the Starting Windows screen. I have tried booting a Windows CD (Windows 8 Retail Installer) to see if I could upgrade it to fix this issue, however that froze at a blank screen after it got past the boot logo. I have tried changing around the BIOS settings (including resetting), to no avail. I have tried re-plugging the internal PSU cables (this is a custom-built desktop), yet this has changed nothing. I can boot into a loopback Ubuntu install on the same drive, which works fine, other than the fact that it has issues with some of the USB ports and the network card. This system has worked fine for the past few months, completely stable, and nothing in the configuration has changed before this error started happening. Startup Repair on the Windows recovery CD doesn't find any issues. Unplugging my secondary hard drive or swapping around memory doesn't change anything. The hard drive itself is fine, it hasn't shown any signs of failure and once again, boots my other OS fine. If anyone could help with this, that would be great. I can't seem to find any possible solution to this. If it makes any difference, my system specs are as follows: AMD FX-8320 Gigabyte GA-970A-D3 4GB of DDR3 Radeon HD 6870 550w PSU I'd like to not have to reinstall Windows, for I have more than a terabyte of data that I would have to back up if that becomes the only option. EDIT: I have since tried the following: Tried the solution involving restoring files from RegBackup, which changed nothing. Tried testing everything with Hiren's boot CD, everything comes back as fine. Tried disabling everything unnecessary in the BIOS and unplugging everything unneeded, it still hangs. Tried swapping out every possible combination of RAM, it still has the same result. The RAM is not at fault it seems Tried every GPU I own (which is many!) and it still hangs at the exact same place. Tried minimizing the power consumption as much as possible, even using an old PCI graphics card. It still hangs at the same place in the same way, signifying that it's not the PSU at fault. Tried resetting the BIOS again, still nothing. Tried every possible combination of BIOS options, even downclocking everything, it still hangs in the same spot. Tried upgrading the BIOS from version FB to FD, which changed nothing. Based on this, I would conclude the motherboard to be at fault. Are there any other possibilities? I don't want to spend $150 for a new motherboard. EDIT 2: This is what it gets stuck at when I try to boot into safe mode: Note the slight graphical corruption at the top of the screen. No matter how I set up the system, this seems to be there. In addition, either it has stopped booting into safe mode now, or it takes upwards of 2+ hours, and I haven't left it running for that long.

  Read the article

• Connecting PC to TV via HDMI/DVI: Windows XP doesn't allow the appropriate screen resolution

  - by Jørgen

  I have a computer that is connected to the living room TV (a Panasonic) via HDMI. There is no other monitor connected. My problem is that the computer, which is running Windows XP, does not allow me to set the proper resolution for the TV. Both the graphics adapter and the TV should support the 1280x720 resolution, but it cannot be selected - the only available options are 1280x600 and 800x600, both in the "native" Windows dialog box and the custom Intel graphics options dialog box. Do anyone have a suggestion for a solution for this? Things I've thought of: Setting the resolution directly in the registry (where?) Installing some "custom" monitor driver (the TV manufacturer does not appear to provide any, currently the "generic" one is used) Details on the setup: Connection: DVI output on the computer via a passive DVI-HDMI adapter to the HDMI input on the TV, audio is run on a separate link, the TV is able to combine video and audio without any problem, the problem is there regardless of whether or not the audio is connected. The connection is several meters long through some walls, for this reason using a VGA cable instead is not an option. Note that the report explicitly says that the TV supports 1280x720. Still, I am not allowed to select it in Graphics Options, only 1280x600 and 800x600 is available. For 800x600, there's a lot of black around the edges; for 1280x600, the screen is "zoomed" so the edges of the monitor image (like the taskbar) is not visible. Other: The computer is running Windows XP. More recent versions of Windows are not an option (I have no licence). Linux is probably not an option (some of the video streaming sites I plan to use do not support it, I think) I wrote the rest of the details below. Thanks for any help!! TV: Panasonic TX-L32X10Y, European version; a 720p 32" quite "regular" LCD TV. Allowed resolutions according to manual: Signal name: 640x480 @60HZ Horizontal frequency: 31.47 kHz Vertical frequency: 60Hz Signal name: 750/720) /60p Horizontal frequency: 45.00 kHz Vertical frequency: 60Hz Signal name: 1,125 (1,080) / 60p Horizontal frequency: 67.50 kHz Vertical frequency: 60Hz (this is exactly how the manual presents it. PC via D-SUB (VGA cable) and "regular" HDMI have more alternatives.) Messing with the "zoom" settings on the TV does not affect the available resolution options on the computer. Computer: The following is a printout from one of the graphics adapter option pages. I think it covers most of it. The computer is a Dell. INTEL(R) EXTREME GRAPHICS 2 REPORT Report Date: 04/17/2011 Report Time[hr:mm:ss]: 20:18:02 Driver Version: 6.14.10.4396 Operating System: Windows XP* Professional, Service Pack 3 (5.1.2600) Default Language: English DirectX* Version: 9.0 Physical Memory: 1021 MB Minimum Graphics Memory: 1 MB Maximum Graphics Memory: 96 MB Graphics Memory in Use: 6 MB Processor: x86 Processor Speed: 2593 MHZ Vendor ID: 8086 Device ID: 2572 Device Revision: 02 * Accelerator Information * Accelerator in Use: Intel(R) 82865G Graphics Controller Video BIOS: 2972 Current Graphics Mode: 1280 by 600 True Color (60 Hz) * Devices Connected to the Graphics Accelerator * Active Digital Displays: 1 * Digital Display * Monitor Name: Plug and Play Monitor Display Type: Digital Gamma Value: 2.20 DDC2 Protocol: Supported Maximum Image Size: Horizontal: Not Available Vertical: Not Available Monitor Supported Modes: 1280 by 720 (50 Hz) 1280 by 720 (60 Hz) Display Power Management Support: Standby Mode: Not Supported Suspend Mode: Not Supported Active Off Mode: Not Supported (disclaimer: this question was also asked at the Wikipedia Reference Desk some time ago and might show up in a Google search. I got no useful answers there.)

  Read the article

• Metro: Understanding CSS Media Queries

  - by Stephen.Walther

  If you are building a Metro style application then your application needs to look great when used on a wide variety of devices. Your application needs to work on tiny little phones, slates, desktop monitors, and the super high resolution displays of the future. Your application also must support portable devices used with different orientations. If someone tilts their phone from portrait to landscape mode then your application must still be usable. Finally, your Metro style application must look great in different states. For example, your Metro application can be in a “snapped state” when it is shrunk so it can share screen real estate with another application. In this blog post, you learn how to use Cascading Style Sheet media queries to support different devices, different device orientations, and different application states. First, you are provided with an overview of the W3C Media Query recommendation and you learn how to detect standard media features. Next, you learn about the Microsoft extensions to media queries which are supported in Metro style applications. For example, you learn how to use the –ms-view-state feature to detect whether an application is in a “snapped state” or “fill state”. Finally, you learn how to programmatically detect the features of a device and the state of an application. You learn how to use the msMatchMedia() method to execute a media query with JavaScript. Using CSS Media Queries Media queries enable you to apply different styles depending on the features of a device. Media queries are not only supported by Metro style applications, most modern web browsers now support media queries including Google Chrome 4+, Mozilla Firefox 3.5+, Apple Safari 4+, and Microsoft Internet Explorer 9+. Loading Different Style Sheets with Media Queries Imagine, for example, that you want to display different content depending on the horizontal resolution of a device. In that case, you can load different style sheets optimized for different sized devices. Consider the following HTML page: <!DOCTYPE html> <html xmlns="http://www.w3.org/1999/xhtml"> <head> <title>U.S. Robotics and Mechanical Men</title> <link href="main.css" rel="stylesheet" type="text/css" /> <!-- Less than 1100px --> <link href="medium.css" rel="stylesheet" type="text/css" media="(max-width:1100px)" /> <!-- Less than 800px --> <link href="small.css" rel="stylesheet" type="text/css" media="(max-width:800px)" /> </head> <body> <div id="header"> <h1>U.S. Robotics and Mechanical Men</h1> </div> <!-- Advertisement Column --> <div id="leftColumn"> <img src="advertisement1.gif" alt="advertisement" /> <img src="advertisement2.jpg" alt="advertisement" /> </div> <!-- Product Search Form --> <div id="mainContentColumn"> <label>Search Products</label> <input id="search" /><button>Search</button> </div> <!-- Deal of the Day Column --> <div id="rightColumn"> <h1>Deal of the Day!</h1> <p> Buy two cameras and get a third camera for free! Offer is good for today only. </p> </div> </body> </html> The HTML page above contains three columns: a leftColumn, mainContentColumn, and rightColumn. When the page is displayed on a low resolution device, such as a phone, only the mainContentColumn appears: When the page is displayed in a medium resolution device, such as a slate, both the leftColumn and the mainContentColumns are displayed: Finally, when the page is displayed in a high-resolution device, such as a computer monitor, all three columns are displayed: Different content is displayed with the help of media queries. The page above contains three style sheet links. Two of the style links include a media attribute: <link href="main.css" rel="stylesheet" type="text/css" /> <!-- Less than 1100px --> <link href="medium.css" rel="stylesheet" type="text/css" media="(max-width:1100px)" /> <!-- Less than 800px --> <link href="small.css" rel="stylesheet" type="text/css" media="(max-width:800px)" /> The main.css style sheet contains default styles for the elements in the page. The medium.css style sheet is applied when the page width is less than 1100px. This style sheet hides the rightColumn and changes the page background color to lime: html { background-color: lime; } #rightColumn { display:none; } Finally, the small.css style sheet is loaded when the page width is less than 800px. This style sheet hides the leftColumn and changes the page background color to red: html { background-color: red; } #leftColumn { display:none; } The different style sheets are applied as you stretch and contract your browser window. You don’t need to refresh the page after changing the size of the page for a media query to be applied: Using the @media Rule You don’t need to divide your styles into separate files to take advantage of media queries. You can group styles by using the @media rule. For example, the following HTML page contains one set of styles which are applied when a device’s orientation is portrait and another set of styles when a device’s orientation is landscape: <!DOCTYPE html> <html> <head> <meta charset="utf-8" /> <title>Application1</title> <style type="text/css"> html { font-family:'Segoe UI Semilight'; font-size: xx-large; } @media screen and (orientation:landscape) { html { background-color: lime; } p.content { width: 50%; margin: auto; } } @media screen and (orientation:portrait) { html { background-color: red; } p.content { width: 90%; margin: auto; } } </style> </head> <body> <p class="content"> Lorem ipsum dolor sit amet, consectetuer adipiscing elit. Maecenas porttitor congue massa. Fusce posuere, magna sed pulvinar ultricies, purus lectus malesuada libero, sit amet commodo magna eros quis urna. </p> </body> </html> When a device has a landscape orientation then the background color is set to the color lime and the text only takes up 50% of the available horizontal space: When the device has a portrait orientation then the background color is red and the text takes up 90% of the available horizontal space: Using Standard CSS Media Features The official list of standard media features is contained in the W3C CSS Media Query recommendation located here: http://www.w3.org/TR/css3-mediaqueries/ Here is the official list of the 13 media features described in the standard: · width – The current width of the viewport · height – The current height of the viewport · device-width – The width of the device · device-height – The height of the device · orientation – The value portrait or landscape · aspect-ratio – The ratio of width to height · device-aspect-ratio – The ratio of device width to device height · color – The number of bits per color supported by the device · color-index – The number of colors in the color lookup table of the device · monochrome – The number of bits in the monochrome frame buffer · resolution – The density of the pixels supported by the device · scan – The values progressive or interlace (used for TVs) · grid – The values 0 or 1 which indicate whether the device supports a grid or a bitmap Many of the media features in the list above support the min- and max- prefix. For example, you can test for the min-width using a query like this: (min-width:800px) You can use the logical and operator with media queries when you need to check whether a device supports more than one feature. For example, the following query returns true only when the width of the device is between 800 and 1,200 pixels: (min-width:800px) and (max-width:1200px) Finally, you can use the different media types – all, braille, embossed, handheld, print, projection, screen, speech, tty, tv — with a media query. For example, the following media query only applies to a page when a page is being printed in color: print and (color) If you don’t specify a media type then media type all is assumed. Using Metro Style Media Features Microsoft has extended the standard list of media features which you can include in a media query with two custom media features: · -ms-high-contrast – The values any, black-white, white-black · -ms-view-state – The values full-screen, fill, snapped, device-portrait You can take advantage of the –ms-high-contrast media feature to make your web application more accessible to individuals with disabilities. In high contrast mode, you should make your application easier to use for individuals with vision disabilities. The –ms-view-state media feature enables you to detect the state of an application. For example, when an application is snapped, the application only occupies part of the available screen real estate. The snapped application appears on the left or right side of the screen and the rest of the screen real estate is dominated by the fill application (Metro style applications can only be snapped on devices with a horizontal resolution of greater than 1,366 pixels). Here is a page which contains style rules for an application in both a snap and fill application state: <!DOCTYPE html> <html> <head> <meta charset="utf-8" /> <title>MyWinWebApp</title> <style type="text/css"> html { font-family:'Segoe UI Semilight'; font-size: xx-large; } @media screen and (-ms-view-state:snapped) { html { background-color: lime; } } @media screen and (-ms-view-state:fill) { html { background-color: red; } } </style> </head> <body> <p class="content"> Lorem ipsum dolor sit amet, consectetuer adipiscing elit. Maecenas porttitor congue massa. Fusce posuere, magna sed pulvinar ultricies, purus lectus malesuada libero, sit amet commodo magna eros quis urna. </p> </body> </html> When the application is snapped, the application appears with a lime background color: When the application state is fill then the background color changes to red: When the application takes up the entire screen real estate – it is not in snapped or fill state – then no special style rules apply and the application appears with a white background color. Querying Media Features with JavaScript You can perform media queries using JavaScript by taking advantage of the window.msMatchMedia() method. This method returns a MSMediaQueryList which has a matches method that represents success or failure. For example, the following code checks whether the current device is in portrait mode: if (window.msMatchMedia("(orientation:portrait)").matches) { console.log("portrait"); } else { console.log("landscape"); } If the matches property returns true, then the device is in portrait mode and the message “portrait” is written to the Visual Studio JavaScript Console window. Otherwise, the message “landscape” is written to the JavaScript Console window. You can create an event listener which triggers code whenever the results of a media query changes. For example, the following code writes a message to the JavaScript Console whenever the current device is switched into or out of Portrait mode: window.msMatchMedia("(orientation:portrait)").addListener(function (mql) { if (mql.matches) { console.log("Switched to portrait"); } }); Be aware that the event listener is triggered whenever the result of the media query changes. So the event listener is triggered both when you switch from landscape to portrait and when you switch from portrait to landscape. For this reason, you need to verify that the matches property has the value true before writing the message. Summary The goal of this blog entry was to explain how CSS media queries work in the context of a Metro style application written with JavaScript. First, you were provided with an overview of the W3C CSS Media Query recommendation. You learned about the standard media features which you can query such as width and orientation. Next, we focused on the Microsoft extensions to media queries. You learned how to use –ms-view-state to detect whether a Metro style application is in “snapped” or “fill” state. You also learned how to use the msMatchMedia() method to perform a media query from JavaScript.

  Read the article

• The case of the phantom ADF developer (and other yarns)

  - by Chris Muir

  A few years of ADF experience means I see common mistakes made by different developers, some I regularly make myself.  This post is designed to assist beginners to Oracle JDeveloper Application Development Framework (ADF) avoid a common ADF pitfall, the case of the phantom ADF developer [add Scooby-Doo music here]. ADF Business Components - triggers, default table values and instead of views. Oracle's JDeveloper tutorials help with the A-B-Cs of ADF development, typically built on the nice 'n safe demo schema provided by with the Oracle database such as the HR demo schema. However it's not too long until ADF beginners, having built up some confidence from learning with the tutorials and vanilla demo schemas, start building ADF Business Components based upon their own existing database schema objects.  This is where unexpected problems can sneak in. The crime Developers may encounter a surprising error at runtime when editing a record they just created or updated and committed to the database, based on their own existing tables, namely the error: JBO-25014: Another user has changed the row with primary key oracle.jbo.Key[x] ...where X is the primary key value of the row at hand.  In a production environment with multiple users this error may be legit, one of the other users has updated the row since you queried it.  Yet in a development environment this error is just plain confusing.  If developers are isolated in their own database, creating and editing records they know other users can't possibly be working with, or all the other developers have gone home for the day, how is this error possible? There are no other users?  It must be the phantom ADF developer! [insert dramatic music here] The following picture is what you'll see in the Business Component Browser, and you'll receive a similar error message via an ADF Faces page: A false conclusion What can possibly cause this issue if it isn't our phantom ADF developer?  Doesn't ADF BC implement record locking, locking database records when the row is modified in the ADF middle-tier by a user?  How can our phantom ADF developer even take out a lock if this is the case?  Maybe ADF has a bug, maybe ADF isn't implementing record locking at all?  Shouldn't we see the error "JBO-26030: Failed to lock the record, another user holds the lock" as we attempt to modify the record, why do we see JBO-25014? : Let's verify that ADF is in fact issuing the correct SQL LOCK-FOR-UPDATE statement to the database. First we need to verify ADF's locking strategy.  It is determined by the Application Module's jbo.locking.mode property.  The default (as of JDev 11.1.1.4.0 if memory serves me correct) and recommended value is optimistic, and the other valid value is pessimistic. Next we need a mechanism to check that ADF is issuing the LOCK statements to the database.  We could ask DBAs to monitor locks with OEM, but optimally we'd rather not involve overworked DBAs in this process, so instead we can use the ADF runtime setting –Djbo.debugoutput=console.  At runtime this options turns on instrumentation within the ADF BC layer, which among a lot of extra detail displayed in the log window, will show the actual SQL statement issued to the database, including the LOCK statement we're looking to confirm. Setting our locking mode to pessimistic, opening the Business Components Browser of a JSF page allowing us to edit a record, say the CHARGEABLE field within a BOOKINGS record where BOOKING_NO = 1206, upon editing the record see among others the following log entries: [421] Built select: 'SELECT BOOKING_NO, EVENT_NO, RESOURCE_CODE, CHARGEABLE, MADE_BY, QUANTITY, COST, STATUS, COMMENTS FROM BOOKINGS Bookings'[422] Executing LOCK...SELECT BOOKING_NO, EVENT_NO, RESOURCE_CODE, CHARGEABLE, MADE_BY, QUANTITY, COST, STATUS, COMMENTS FROM BOOKINGS Bookings WHERE BOOKING_NO=:1 FOR UPDATE NOWAIT[423] Where binding param 1: 1206  As can be seen on line 422, in fact a LOCK-FOR-UPDATE is indeed issued to the database.  Later when we commit the record we see: [441] OracleSQLBuilder: SAVEPOINT 'BO_SP'[442] OracleSQLBuilder Executing, Lock 1 DML on: BOOKINGS (Update)[443] UPDATE buf Bookings>#u SQLStmtBufLen: 210, actual=62[444] UPDATE BOOKINGS Bookings SET CHARGEABLE=:1 WHERE BOOKING_NO=:2[445] Update binding param 1: N[446] Where binding param 2: 1206[447] BookingsView1 notify COMMIT ... [448] _LOCAL_VIEW_USAGE_model_Bookings_ResourceTypesView1 notify COMMIT ... [449] EntityCache close prepared statement ....and as a result the changes are saved to the database, and the lock is released. Let's see what happens when we use the optimistic locking mode, this time to change the same BOOKINGS record CHARGEABLE column again.  As soon as we edit the record we see little activity in the logs, nothing to indicate any SQL statement, let alone a LOCK has been taken out on the row. However when we save our records by issuing a commit, the following is recorded in the logs: [509] OracleSQLBuilder: SAVEPOINT 'BO_SP'[510] OracleSQLBuilder Executing doEntitySelect on: BOOKINGS (true)[511] Built select: 'SELECT BOOKING_NO, EVENT_NO, RESOURCE_CODE, CHARGEABLE, MADE_BY, QUANTITY, COST, STATUS, COMMENTS FROM BOOKINGS Bookings'[512] Executing LOCK...SELECT BOOKING_NO, EVENT_NO, RESOURCE_CODE, CHARGEABLE, MADE_BY, QUANTITY, COST, STATUS, COMMENTS FROM BOOKINGS Bookings WHERE BOOKING_NO=:1 FOR UPDATE NOWAIT[513] Where binding param 1: 1205[514] OracleSQLBuilder Executing, Lock 2 DML on: BOOKINGS (Update)[515] UPDATE buf Bookings>#u SQLStmtBufLen: 210, actual=62[516] UPDATE BOOKINGS Bookings SET CHARGEABLE=:1 WHERE BOOKING_NO=:2[517] Update binding param 1: Y[518] Where binding param 2: 1205[519] BookingsView1 notify COMMIT ... [520] _LOCAL_VIEW_USAGE_model_Bookings_ResourceTypesView1 notify COMMIT ... [521] EntityCache close prepared statement Again even though we're seeing the midtier delay the LOCK statement until commit time, it is in fact occurring on line 412, and released as part of the commit issued on line 419.  Therefore with either optimistic or pessimistic locking a lock is indeed issued. Our conclusion at this point must be, unless there's the unlikely cause the LOCK statement is never really hitting the database, or the even less likely cause the database has a bug, then ADF does in fact take out a lock on the record before allowing the current user to update it.  So there's no way our phantom ADF developer could even modify the record if he tried without at least someone receiving a lock error. Hmm, we can only conclude the locking mode is a red herring and not the true cause of our problem.  Who is the phantom? At this point we'll need to conclude that the error message "JBO-25014: Another user has changed" is somehow legit, even though we don't understand yet what's causing it. This leads onto two further questions, how does ADF know another user has changed the row, and what's been changed anyway? To answer the first question, how does ADF know another user has changed the row, the Fusion Guide's section 4.10.11 How to Protect Against Losing Simultaneous Updated Data , that details the Entity Object Change-Indicator property, gives us the answer: At runtime the framework provides automatic "lost update" detection for entity objects to ensure that a user cannot unknowingly modify data that another user has updated and committed in the meantime. Typically, this check is performed by comparing the original values of each persistent entity attribute against the corresponding current column values in the database at the time the underlying row is locked. Before updating a row, the entity object verifies that the row to be updated is still consistent with the current state of the database.  The guide further suggests to make this solution more efficient: You can make the lost update detection more efficient by identifying any attributes of your entity whose values you know will be updated whenever the entity is modified. Typical candidates include a version number column or an updated date column in the row.....To detect whether the row has been modified since the user queried it in the most efficient way, select the Change Indicator option to compare only the change-indicator attribute values. We now know that ADF BC doesn't use the locking mechanism at all to protect the current user against updates, but rather it keeps a copy of the original record fetched, separate to the user changed version of the record, and it compares the original record against the one in the database when the lock is taken out.  If values don't match, be it the default compare-all-columns behaviour, or the more efficient Change Indicator mechanism, ADF BC will throw the JBO-25014 error. This leaves one last question.  Now we know the mechanism under which ADF identifies a changed row, what we don't know is what's changed and who changed it? The real culprit What's changed?  We know the record in the mid-tier has been changed by the user, however ADF doesn't use the changed record in the mid-tier to compare to the database record, but rather a copy of the original record before it was changed.  This leaves us to conclude the database record has changed, but how and by who? There are three potential causes: Database triggers The database trigger among other uses, can be configured to fire PLSQL code on a database table insert, update or delete.  In particular in an insert or update the trigger can override the value assigned to a particular column.  The trigger execution is actioned by the database on behalf of the user initiating the insert or update action. Why this causes the issue specific to our ADF use, is when we insert or update a record in the database via ADF, ADF keeps a copy of the record written to the database.  However the cached record is instantly out of date as the database triggers have modified the record that was actually written to the database.  Thus when we update the record we just inserted or updated for a second time to the database, ADF compares its original copy of the record to that in the database, and it detects the record has been changed – giving us JBO-25014. This is probably the most common cause of this problem. Default values A second reason this issue can occur is another database feature, default column values.  When creating a database table the schema designer can define default values for specific columns.  For example a CREATED_BY column could be set to SYSDATE, or a flag column to Y or N.  Default values are only used by the database when a user inserts a new record and the specific column is assigned NULL.  The database in this case will overwrite the column with the default value. As per the database trigger section, it then becomes apparent why ADF chokes on this feature, though it can only specifically occur in an insert-commit-update-commit scenario, not the update-commit-update-commit scenario. Instead of trigger views I must admit I haven't double checked this scenario but it seems plausible, that of the Oracle database's instead of trigger view (sometimes referred to as instead of views).  A view in the database is based on a query, and dependent on the queries complexity, may support insert, update and delete functionality to a limited degree.  In order to support fully insertable, updateable and deletable views, Oracle introduced the instead of view, that gives the view designer the ability to not only define the view query, but a set of programmatic PLSQL triggers where the developer can define their own logic for inserts, updates and deletes. While this provides the database programmer a very powerful feature, it can cause issues for our ADF application.  On inserting or updating a record in the instead of view, the record and it's data that goes in is not necessarily the data that comes out when ADF compares the records, as the view developer has the option to practically do anything with the incoming data, including throwing it away or pushing it to tables which aren't used by the view underlying query for fetching the data. Readers are at this point reminded that this article is specifically about how the JBO-25014 error occurs in the context of 1 developer on an isolated database.  The article is not considering how the error occurs in a production environment where there are multiple users who can cause this error in a legitimate fashion.  Assuming none of the above features are the cause of the problem, and optimistic locking is turned on (this error is not possible if pessimistic locking is the default mode *and* none of the previous causes are possible), JBO-25014 is quite feasible in a production ADF application if 2 users modify the same record. At this point under project timelines pressure, the obvious fix for developers is to drop both database triggers and default values from the underlying tables.  However we must be careful that these legacy constructs aren't used and assumed to be in place by other legacy systems.  Dropping the database triggers or default value that the existing Oracle Forms  applications assumes and requires to be in place could cause unexpected behaviour and bugs in the Forms application.  Proficient software engineers would recognize such a change may require a partial or full regression test of the existing legacy system, a potentially costly and timely exercise, not ideal. Solving the mystery once and for all Luckily ADF has built in functionality to deal with this issue, though it's not a surprise, as Oracle as the author of ADF also built the database, and are fully aware of the Oracle database's feature set.  At the Entity Object attribute level, the Refresh After Insert and Refresh After Update properties.  Simply selecting these instructs ADF BC after inserting or updating a record to the database, to expect the database to modify the said attributes, and read a copy of the changed attributes back into its cached mid-tier record.  Thus next time the developer modifies the current record, the comparison between the mid-tier record and the database record match, and JBO-25014: Another user has changed" is no longer an issue. [Post edit - as per the comment from Oracle's Steven Davelaar below, as he correctly points out the above solution will not work for instead-of-triggers views as it relies on SQL RETURNING clause which is incompatible with this type of view] Alternatively you can set the Change Indicator on one of the attributes.  This will work as long as the relating column for the attribute in the database itself isn't inadvertently updated.  In turn you're possibly just masking the issue rather than solving it, because if another developer turns the Change Indicator back on the original issue will return.

  Read the article

• Handling HumanTask attachments in Oracle BPM 11g PS4FP+ (II)

  - by ccasares

  Retrieving uploaded attachments -UCM- As stated in my previous blog entry, Oracle BPM 11g 11.1.1.5.1 (aka PS4FP) introduced a new cool feature whereby you can use Oracle WebCenter Content (previously known as Oracle UCM) as the repository for the human task attached documents. For more information about how to use or enable this feature, have a look here. The attachment scope (either TASK or PROCESS) also applies to UCM-attachments. But even with this other feature, one question might arise when using UCM attachments. How can I get them from within the process? The first answer would be to use the same getTaskAttachmentContents() XPath function already explained in my previous blog entry. In fact, that's the way it should be. But in Oracle BPM 11g 11.1.1.5.1 (PS4FP) and 11.1.1.6.0 (PS5) there's a bug that prevents you to do that. If you invoke such function against a UCM-attachment, you'll get a null content response (bug#13907552). Even if the attachment was correctly uploaded. While this bug gets fixed, next I will show a workaround that lets me to retrieve the UCM-attached documents from within a BPM process. Besides, the sample will show how to interact with WCC API from within a BPM process.Aside note: I suggest you to read my previous blog entry about Human Task attachments where I briefly describe some concepts that are used next, such as the execData/attachment[] structure. Sample Process I will be using the following sample process: A dummy UserTask using "HumanTask2" Human Task, followed by an Embedded Subprocess that will retrieve the attachments payload. In this case, and here's the key point of the sample, we will retrieve such payload using WebCenter Content WebService API (IDC): and once retrieved, we will write each of them back to a file in the server using a File Adapter service: In detail:  We will use the same attachmentCollection XSD structure and same BusinessObject definition as in the previous blog entry. However we create a separate variable, named attachmentUCM, based on such BusinessObject. We will still need to keep a copy of the HumanTask output's execData structure. Therefore we need to create a new variable of type TaskExecutionData (different one than the other used for non-UCM attachments): As in the non-UCM attachments flow, in the output tab of the UserTask mapping, we'll keep a copy of the execData structure: Now we get into the embedded subprocess that will retrieve the attachments' payload. First, and using an XSLT transformation, we feed the attachmentUCM variable with the following information: The name of each attachment (from execData/attachment/name element) The WebCenter Content ID of the uploaded attachment. This info is stored in execData/attachment/URI element with the format ecm://<id>. As we just want the numeric <id>, we need to get rid of the protocol prefix ("ecm://"). We do so with some XPath functions as detailed below: with these two functions being invoked, respectively: We, again, set the target payload element with an empty string, to get the <payload></payload> tag created. The complete XSLT transformation is shown below. Remember that we're using the XSLT for-each node to create as many target structures as necessary.  Once we have fed the attachmentsUCM structure and so it now contains the name of each of the attachments along with each WCC unique id (dID), it is time to iterate through it and get the payload. Therefore we will use a new embedded subprocess of type MultiInstance, that will iterate over the attachmentsUCM/attachment[] element: In each iteration we will use a Service activity that invokes WCC API through a WebService. Follow these steps to create and configure the Partner Link needed: Login to WCC console with an administrator user (i.e. weblogic). Go to Administration menu and click on "Soap Wsdls" link. We will use the GetFile service to retrieve a file based on its dID. Thus we'll need such service WSDL definition that can be downloaded by clicking the GetFile link. Save the WSDL file in your JDev project folder. In the BPM project's composite view, drag & drop a WebService adapter to create a new External Reference, based on the just added GetFile.wsdl. Name it UCM_GetFile. WCC services are secured through basic HTTP authentication. Therefore we need to enable the just created reference for that: Right-click the reference and click on Configure WS Policies. Under the Security section, click "+" to add the "oracle/wss_username_token_client_policy" policy The last step is to set the credentials for the security policy. For the sample we will use the admin user for WCC (weblogic/welcome1). Open the composite.xml file and select the Source view. Search for the UCM_GetFile entry and add the following highlighted elements into it:   <reference name="UCM_GetFile" ui:wsdlLocation="GetFile.wsdl">     <interface.wsdl interface="http://www.stellent.com/GetFile/#wsdl.interface(GetFileSoap)"/>     <binding.ws port="http://www.stellent.com/GetFile/#wsdl.endpoint(GetFile/GetFileSoap)"                 location="GetFile.wsdl" soapVersion="1.1">       <wsp:PolicyReference URI="oracle/wss_username_token_client_policy"                            orawsp:category="security" orawsp:status="enabled"/>       <property name="weblogic.wsee.wsat.transaction.flowOption"                 type="xs:string" many="false">WSDLDriven</property>       <property name="oracle.webservices.auth.username"                 type="xs:string">weblogic</property>       <property name="oracle.webservices.auth.password"                 type="xs:string">welcome1</property>     </binding.ws>   </reference> Now the new external reference is ready: Once the reference has just been created, we should be able now to use it from our BPM process. However we find here a problem. The WCC GetFile service operation that we will use, GetFileByID, accepts as input a structure similar to this one, where all element tags are optional: <get:GetFileByID xmlns:get="http://www.stellent.com/GetFile/">    <get:dID>?</get:dID>   <get:rendition>?</get:rendition>   <get:extraProps>      <get:property>         <get:name>?</get:name>         <get:value>?</get:value>      </get:property>   </get:extraProps></get:GetFileByID> and we need to fill up just the <get:dID> tag element. Due to some kind of restriction or bug on WCC, the rest of the tag elements must NOT be sent, not even empty (i.e.: <get:rendition></get:rendition> or <get:rendition/>). A sample request that performs the query just by the dID, must be in the following format: <get:GetFileByID xmlns:get="http://www.stellent.com/GetFile/">   <get:dID>12345</get:dID></get:GetFileByID> The issue here is that the simple mapping in BPM does create empty tags being a sample result as follows: <get:GetFileByID xmlns:get="http://www.stellent.com/GetFile/"> <get:dID>12345</get:dID> <get:rendition/> <get:extraProps/> </get:GetFileByID> Although the above structure is perfectly valid, it is not accepted by WCC. Therefore, we need to bypass the problem. The workaround we use (many others are available) is to add a Mediator component between the BPM process and the Service that simply copies the input structure from BPM but getting rid of the empty tags. Follow these steps to configure the Mediator: Drag & drop a new Mediator component into the composite. Uncheck the creation of the SOAP bindings and use the Interface Definition from WSDL template and select the existing GetFile.wsdl Double click in the mediator to edit it. Add a static routing rule to the GetFileByID operation, of type Service and select References/UCM_GetFile/GetFileByID target service: Create the request and reply XSLT mappers: Make sure you map only the dID element in the request: And do an Auto-mapper for the whole response: Finally, we can now add and configure the Service activity in the BPM process. Drag & drop it to the embedded subprocess and select the NormalizedGetFile service and getFileByID operation: Map both the input: ...and the output: Once this embedded subprocess ends, we will have all attachments (name + payload) in the attachmentsUCM variable, which is the main goal of this sample. But in order to test everything runs fine, we finish the sample writing each attachment to a file. To that end we include a final embedded subprocess to concurrently iterate through each attachmentsUCM/attachment[] element: On each iteration we will use a Service activity that invokes a File Adapter write service. In here we have two important parameters to set. First, the payload itself. The file adapter awaits binary data in base64 format (string). We have to map it using XPath (Simple mapping doesn't recognize a String as a base64-binary valid target): Second, we must set the target filename using the Service Properties dialog box: Again, note how we're making use of the loopCounter index variable to get the right element within the embedded subprocess iteration. Final blog entry about attachments will handle how to inject documents to Human Tasks from the BPM process and how to share attachments between different User Tasks. Will come soon. Again, once I finish will all posts on this matter, I will upload the whole sample project to java.net.

  Read the article

• MacBook Pro Late 2009 SATA Resets, Slowness (Is my motherboard dying on both machines?)

  - by A Student at a University

  My MacBook Pro runs slower the longer it's on. I am getting kernel warnings. Some, but not all, resets correlate with AC power connects and disconnects. I don't think the warnings do. (How do I tell?) What are these errors? What causes them? Can this damage the drive or corrupt data? What is it seeing that motivates these? 02:37:16[ 0.791992] ahci 0000:00:0b.0: PCI INT A -> Link[LSI0] -> GSI 20 (level, low) -> IRQ 20 02:37:16[ 0.792047] ahci 0000:00:0b.0: irq 43 for MSI/MSI-X 02:37:16[ 0.792053] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP 02:37:16[ 0.792104] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 1.5 Gbps 0x3 impl IDE mode 02:37:16[ 0.792107] ahci 0000:00:0b.0: flags: 64bit ncq sntf pm led pio slum part boh 02:37:16[ 0.792111] ahci 0000:00:0b.0: setting latency timer to 64 02:37:16[ 0.813473] scsi0 : ahci 02:37:16[ 0.823340] scsi1 : ahci 02:37:16[ 0.848164] ata1: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484100 irq 43 02:37:16[ 0.848166] ata2: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484180 irq 43 02:37:16[ 1.190132] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.190153] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.213568] ata1.00: ATA-8: OCZ-VERTEX2, 1.23, max UDMA/133 02:37:16[ 1.213572] ata1.00: 195371568 sectors, multi 1: LBA48 NCQ (depth 31/32) 02:37:16[ 1.227293] ata2.00: ATA-8: ST9500420ASG, 0002SDM1, max UDMA/133 02:37:16[ 1.227297] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) 02:37:16[ 1.229570] ata2.00: configured for UDMA/133 02:37:16[ 1.240120] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:37:16[ 1.240123] ata2: irq_stat 0x00000040, connection status changed 02:37:16[ 1.240127] ata2: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:37:16[ 1.240133] ata2: hard resetting link 02:37:16[ 1.260738] ata1.00: configured for UDMA/133 02:37:16[ 1.280111] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:37:16[ 1.280114] ata1: irq_stat 0x00000040, connection status changed 02:37:16[ 1.280118] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:37:16[ 1.280122] ata1: hard resetting link 02:37:16[ 1.990101] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.994215] ata2.00: configured for UDMA/133 02:37:16[ 1.994220] ata2: EH complete 02:37:16[ 2.030097] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 2.090773] ata1.00: configured for UDMA/133 02:37:16[ 2.090778] ata1: EH complete 02:37:16[ 2.090931] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.23 PQ: 0 ANSI: 5 02:37:16[ 2.091045] sd 0:0:0:0: Attached scsi generic sg0 type 0 02:37:16[ 2.091121] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) 02:37:16[ 2.091159] scsi 1:0:0:0: Direct-Access ATA ST9500420ASG 0002 PQ: 0 ANSI: 5 02:37:16[ 2.091163] sd 0:0:0:0: [sda] Write Protect is off 02:37:16[ 2.091165] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 02:37:16[ 2.091183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16[ 2.091252] sd 1:0:0:0: Attached scsi generic sg1 type 0 02:37:16[ 2.091446] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) 02:37:16[ 2.091580] sd 1:0:0:0: [sdb] Write Protect is off 02:37:16[ 2.091582] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 02:37:16[ 2.091637] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16[ 2.093140] sd 0:0:0:0: [sda] Attached SCSI disk 02:37:16[ 2.093773] sd 1:0:0:0: [sdb] Attached SCSI disk 02:37:16[ 2.693899] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) 02:37:16[ 5.483492] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro 02:37:16[ 7.905040] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) 02:37:25[ 19.553095] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:25[ 19.555266] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:25[ 19.641532] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:25[ 19.641532] ata1: irq_stat 0x00000040, connection status changed 02:37:25[ 19.641532] ata1: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:25[ 19.641533] ata1: hard resetting link 02:37:25[ 19.642076] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:25[ 19.642078] ata2: irq_stat 0x00000040, connection status changed 02:37:25[ 19.642081] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:25[ 19.642084] ata2: hard resetting link 02:37:26[ 20.392606] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26[ 20.392610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26[ 20.396697] ata2.00: configured for UDMA/133 02:37:26[ 20.396703] ata2: EH complete 02:37:26[ 20.451491] ata1.00: configured for UDMA/133 02:37:26[ 20.451498] ata1: EH complete 02:37:30[ 24.563725] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:30[ 24.565939] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:30[ 24.627236] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:37:30[ 24.627240] ata1: irq_stat 0x00000040, connection status changed 02:37:30[ 24.627242] ata1: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:37:30[ 24.627246] ata1: hard resetting link 02:37:30[ 24.632241] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:30[ 24.632244] ata2: irq_stat 0x00000040, connection status changed 02:37:30[ 24.632247] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:30[ 24.632250] ata2: hard resetting link 02:37:31[ 25.372582] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31[ 25.382615] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31[ 25.386782] ata2.00: configured for UDMA/133 02:37:31[ 25.386788] ata2: EH complete 02:37:31[ 25.431668] ata1.00: configured for UDMA/133 02:37:31[ 25.431674] ata1: EH complete 02:45:54[ 529.141844] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:55[ 529.544529] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:55[ 529.622561] ata1: limiting SATA link speed to 1.5 Gbps 02:45:55[ 529.622568] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:45:55[ 529.622572] ata1: irq_stat 0x00400040, connection status changed 02:45:55[ 529.622576] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:45:55[ 529.622583] ata1: hard resetting link 02:45:55[ 529.622609] ata2: limiting SATA link speed to 1.5 Gbps 02:45:55[ 529.622613] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:45:55[ 529.622616] ata2: irq_stat 0x00000040, connection status changed 02:45:55[ 529.622620] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:55[ 529.622624] ata2: hard resetting link 02:45:56[ 530.380135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56[ 530.380157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56[ 530.384305] ata2.00: configured for UDMA/133 02:45:56[ 530.384314] ata2: EH complete 02:45:56[ 530.399225] ata1.00: configured for UDMA/133 02:45:56[ 530.399233] ata1: EH complete 02:45:58[ 532.395990] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:45:58[ 532.518270] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:45:58[ 532.590968] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5840000 action 0xe frozen t4 02:45:58[ 532.590973] ata1: irq_stat 0x00000040, connection status changed 02:45:58[ 532.590977] ata1: SError: { CommWake LinkSeq TrStaTrns DevExch } 02:45:58[ 532.590983] ata1: hard resetting link 02:45:58[ 532.591034] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:45:58[ 532.591037] ata2: irq_stat 0x00000040, connection status changed 02:45:58[ 532.591041] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:58[ 532.591045] ata2: hard resetting link 02:45:59[ 533.340147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59[ 533.340168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59[ 533.344416] ata2.00: configured for UDMA/133 02:45:59[ 533.344424] ata2: EH complete 02:45:59[ 533.360839] ata1.00: configured for UDMA/133 02:45:59[ 533.360847] ata1: EH complete 02:45:59[ 533.584449] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:59[ 533.586999] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:59[ 533.660117] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:45:59[ 533.660122] ata2: irq_stat 0x00000040, connection status changed 02:45:59[ 533.660126] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:59[ 533.660132] ata2: hard resetting link 02:45:59[ 533.660141] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:45:59[ 533.660143] ata1: irq_stat 0x00000040, connection status changed 02:45:59[ 533.660147] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:45:59[ 533.660151] ata1: hard resetting link 02:46:00[ 534.412536] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00[ 534.412562] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00[ 534.416768] ata2.00: configured for UDMA/133 02:46:00[ 534.416777] ata2: EH complete 02:46:00[ 534.431396] ata1.00: configured for UDMA/133 02:46:00[ 534.431401] ata1: EH complete 02:46:03[ 537.384649] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:03[ 537.504214] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:03[ 537.585992] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:46:03[ 537.585996] ata1: irq_stat 0x00000040, connection status changed 02:46:03[ 537.585999] ata1: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:46:03[ 537.586002] ata1: hard resetting link 02:46:03[ 537.586028] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:46:03[ 537.586030] ata2: irq_stat 0x00000040, connection status changed 02:46:03[ 537.586033] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:46:03[ 537.586036] ata2: hard resetting link 02:46:04[ 538.330147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04[ 538.330168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04[ 538.334389] ata2.00: configured for UDMA/133 02:46:04[ 538.334398] ata2: EH complete 02:46:04[ 538.343511] ata1.00: configured for UDMA/133 02:46:04[ 538.343519] ata1: EH complete 02:46:04[ 538.456413] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:04[ 538.459404] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:04[ 538.540138] ata1.00: limiting speed to UDMA/100:PIO4 02:46:04[ 538.540144] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:46:04[ 538.540148] ata1: irq_stat 0x00000040, connection status changed 02:46:04[ 538.540153] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:46:04[ 538.540159] ata1: hard resetting link 02:46:04[ 538.540202] ata2.00: limiting speed to UDMA/100:PIO4 02:46:04[ 538.540207] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:46:04[ 538.540211] ata2: irq_stat 0x00000040, connection status changed 02:46:04[ 538.540215] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:46:04[ 538.540220] ata2: hard resetting link 02:46:05[ 539.290054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05[ 539.290041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05[ 539.294100] ata2.00: configured for UDMA/100 02:46:05[ 539.294106] ata2: EH complete 02:46:05[ 539.314125] ata1.00: configured for UDMA/100 02:46:05[ 539.314132] ------------[ cut here ]------------ 02:46:05[ 539.314140] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:05[ 539.314144] Hardware name: MacBookPro5,3 02:46:05[ 539.314146] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:05[ 539.314221] Pid: 202, comm: scsi_eh_0 Tainted: P 2.6.35-25-generic #44-Ubuntu 02:46:05[ 539.314224] Call Trace: 02:46:05[ 539.314233] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:05[ 539.314237] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:05[ 539.314242] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:05[ 539.314246] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:05[ 539.314256] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:05[ 539.314261] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:05[ 539.314266] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:05[ 539.314270] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:05[ 539.314275] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:05[ 539.314280] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:05[ 539.314284] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:05[ 539.314288] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:05[ 539.314291] ---[ end trace 76dbffc2d5d49d9b ]--- 02:46:05[ 539.314296] ata1: EH complete 02:46:12[ 547.040091] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen 02:46:12[ 547.040098] ata1.00: failed command: IDENTIFY DEVICE 02:46:12[ 547.040106] ata1.00: cmd ec/00:00:00:00:00/00:00:00:00:00/40 tag 0 pio 512 in 02:46:12[ 547.040108] res 40/00:01:00:00:00/00:00:00:00:00/e0 Emask 0x4 (timeout) 02:46:12[ 547.040111] ata1.00: status: { DRDY } 02:46:12[ 547.040117] ata1: hard resetting link 02:46:13[ 547.390144] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:13[ 547.408430] ata1.00: configured for UDMA/100 02:46:13[ 547.408438] ------------[ cut here ]------------ 02:46:13[ 547.408447] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:13[ 547.408451] Hardware name: MacBookPro5,3 02:46:13[ 547.408453] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:13[ 547.408528] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 02:46:13[ 547.408531] Call Trace: 02:46:13[ 547.408540] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:13[ 547.408544] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:13[ 547.408549] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:13[ 547.408553] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:13[ 547.408563] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:13[ 547.408567] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:13[ 547.408572] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:13[ 547.408577] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:13[ 547.408582] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:13[ 547.408587] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:13[ 547.408591] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:13[ 547.408595] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:13[ 547.408598] ---[ end trace 76dbffc2d5d49d9c ]--- 02:46:13[ 547.408620] ata1: EH complete 02:46:13[ 547.562470] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:13[ 547.671380] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:13[ 547.738198] ata1.00: limiting speed to UDMA/33:PIO4 02:46:13[ 547.738204] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:13[ 547.738208] ata1: irq_stat 0x00000040, connection status changed 02:46:13[ 547.738212] ata1: SError: { LinkSeq TrStaTrns DevExch } 02:46:13[ 547.738218] ata1: hard resetting link 02:46:13[ 547.738262] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:46:13[ 547.738265] ata2: irq_stat 0x00000040, connection status changed 02:46:13[ 547.738269] ata2: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:46:13[ 547.738274] ata2: hard resetting link 02:46:14[ 548.482561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14[ 548.484083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14[ 548.486809] ata2.00: configured for UDMA/100 02:46:14[ 548.486818] ata2: EH complete 02:46:14[ 548.498998] ata1.00: configured for UDMA/33 02:46:14[ 548.499004] ata1: EH complete 02:46:18[ 552.410499] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:18[ 552.522521] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:18[ 552.529674] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:18[ 552.529678] ata1: irq_stat 0x00000040, connection status changed 02:46:18[ 552.529680] ata1: SError: { LinkSeq TrStaTrns DevExch } 02:46:18[ 552.529684] ata1: hard resetting link 02:46:18[ 552.529716] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:18[ 552.529718] ata2: irq_stat 0x00000040, connection status changed 02:46:18[ 552.529720] ata2: SError: { LinkSeq TrStaTrns DevExch } 02:46:18[ 552.529723] ata2: hard resetting link 02:46:19[ 553.280059] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19[ 553.280068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19[ 553.284141] ata2.00: configured for UDMA/100 02:46:19[ 553.284150] ata2: EH complete 02:46:19[ 553.301629] ata1.00: configured for UDMA/33 02:46:19[ 553.301637] ata1: EH complete

  Read the article

• MacBook Pro Late 2009 SATA Resets, Slowness (Is my motherboard dying on both machines?)

  - by A Student at a University

  My MacBook Pro runs slower the longer it's on. I am getting kernel warnings. Some, but not all, resets correlate with AC power connects and disconnects. I don't think the warnings do. (How do I tell?) What are these errors? What causes them? Can this damage the drive or corrupt data? What is it seeing that motivates these? 02:37:16[ 0.791992] ahci 0000:00:0b.0: PCI INT A -> Link[LSI0] -> GSI 20 (level, low) -> IRQ 20 02:37:16[ 0.792047] ahci 0000:00:0b.0: irq 43 for MSI/MSI-X 02:37:16[ 0.792053] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP 02:37:16[ 0.792104] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 1.5 Gbps 0x3 impl IDE mode 02:37:16[ 0.792107] ahci 0000:00:0b.0: flags: 64bit ncq sntf pm led pio slum part boh 02:37:16[ 0.792111] ahci 0000:00:0b.0: setting latency timer to 64 02:37:16[ 0.813473] scsi0 : ahci 02:37:16[ 0.823340] scsi1 : ahci 02:37:16[ 0.848164] ata1: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484100 irq 43 02:37:16[ 0.848166] ata2: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484180 irq 43 02:37:16[ 1.190132] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.190153] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.213568] ata1.00: ATA-8: OCZ-VERTEX2, 1.23, max UDMA/133 02:37:16[ 1.213572] ata1.00: 195371568 sectors, multi 1: LBA48 NCQ (depth 31/32) 02:37:16[ 1.227293] ata2.00: ATA-8: ST9500420ASG, 0002SDM1, max UDMA/133 02:37:16[ 1.227297] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) 02:37:16[ 1.229570] ata2.00: configured for UDMA/133 02:37:16[ 1.240120] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:37:16[ 1.240123] ata2: irq_stat 0x00000040, connection status changed 02:37:16[ 1.240127] ata2: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:37:16[ 1.240133] ata2: hard resetting link 02:37:16[ 1.260738] ata1.00: configured for UDMA/133 02:37:16[ 1.280111] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:37:16[ 1.280114] ata1: irq_stat 0x00000040, connection status changed 02:37:16[ 1.280118] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:37:16[ 1.280122] ata1: hard resetting link 02:37:16[ 1.990101] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 1.994215] ata2.00: configured for UDMA/133 02:37:16[ 1.994220] ata2: EH complete 02:37:16[ 2.030097] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16[ 2.090773] ata1.00: configured for UDMA/133 02:37:16[ 2.090778] ata1: EH complete 02:37:16[ 2.090931] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.23 PQ: 0 ANSI: 5 02:37:16[ 2.091045] sd 0:0:0:0: Attached scsi generic sg0 type 0 02:37:16[ 2.091121] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) 02:37:16[ 2.091159] scsi 1:0:0:0: Direct-Access ATA ST9500420ASG 0002 PQ: 0 ANSI: 5 02:37:16[ 2.091163] sd 0:0:0:0: [sda] Write Protect is off 02:37:16[ 2.091165] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 02:37:16[ 2.091183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16[ 2.091252] sd 1:0:0:0: Attached scsi generic sg1 type 0 02:37:16[ 2.091446] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) 02:37:16[ 2.091580] sd 1:0:0:0: [sdb] Write Protect is off 02:37:16[ 2.091582] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 02:37:16[ 2.091637] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16[ 2.093140] sd 0:0:0:0: [sda] Attached SCSI disk 02:37:16[ 2.093773] sd 1:0:0:0: [sdb] Attached SCSI disk 02:37:16[ 2.693899] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) 02:37:16[ 5.483492] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro 02:37:16[ 7.905040] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) 02:37:25[ 19.553095] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:25[ 19.555266] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:25[ 19.641532] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:25[ 19.641532] ata1: irq_stat 0x00000040, connection status changed 02:37:25[ 19.641532] ata1: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:25[ 19.641533] ata1: hard resetting link 02:37:25[ 19.642076] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:25[ 19.642078] ata2: irq_stat 0x00000040, connection status changed 02:37:25[ 19.642081] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:25[ 19.642084] ata2: hard resetting link 02:37:26[ 20.392606] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26[ 20.392610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26[ 20.396697] ata2.00: configured for UDMA/133 02:37:26[ 20.396703] ata2: EH complete 02:37:26[ 20.451491] ata1.00: configured for UDMA/133 02:37:26[ 20.451498] ata1: EH complete 02:37:30[ 24.563725] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:30[ 24.565939] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:30[ 24.627236] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:37:30[ 24.627240] ata1: irq_stat 0x00000040, connection status changed 02:37:30[ 24.627242] ata1: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:37:30[ 24.627246] ata1: hard resetting link 02:37:30[ 24.632241] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:37:30[ 24.632244] ata2: irq_stat 0x00000040, connection status changed 02:37:30[ 24.632247] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:37:30[ 24.632250] ata2: hard resetting link 02:37:31[ 25.372582] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31[ 25.382615] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31[ 25.386782] ata2.00: configured for UDMA/133 02:37:31[ 25.386788] ata2: EH complete 02:37:31[ 25.431668] ata1.00: configured for UDMA/133 02:37:31[ 25.431674] ata1: EH complete 02:45:54[ 529.141844] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:55[ 529.544529] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:55[ 529.622561] ata1: limiting SATA link speed to 1.5 Gbps 02:45:55[ 529.622568] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:45:55[ 529.622572] ata1: irq_stat 0x00400040, connection status changed 02:45:55[ 529.622576] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:45:55[ 529.622583] ata1: hard resetting link 02:45:55[ 529.622609] ata2: limiting SATA link speed to 1.5 Gbps 02:45:55[ 529.622613] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:45:55[ 529.622616] ata2: irq_stat 0x00000040, connection status changed 02:45:55[ 529.622620] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:55[ 529.622624] ata2: hard resetting link 02:45:56[ 530.380135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56[ 530.380157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56[ 530.384305] ata2.00: configured for UDMA/133 02:45:56[ 530.384314] ata2: EH complete 02:45:56[ 530.399225] ata1.00: configured for UDMA/133 02:45:56[ 530.399233] ata1: EH complete 02:45:58[ 532.395990] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:45:58[ 532.518270] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:45:58[ 532.590968] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5840000 action 0xe frozen t4 02:45:58[ 532.590973] ata1: irq_stat 0x00000040, connection status changed 02:45:58[ 532.590977] ata1: SError: { CommWake LinkSeq TrStaTrns DevExch } 02:45:58[ 532.590983] ata1: hard resetting link 02:45:58[ 532.591034] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:45:58[ 532.591037] ata2: irq_stat 0x00000040, connection status changed 02:45:58[ 532.591041] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:58[ 532.591045] ata2: hard resetting link 02:45:59[ 533.340147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59[ 533.340168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59[ 533.344416] ata2.00: configured for UDMA/133 02:45:59[ 533.344424] ata2: EH complete 02:45:59[ 533.360839] ata1.00: configured for UDMA/133 02:45:59[ 533.360847] ata1: EH complete 02:45:59[ 533.584449] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:59[ 533.586999] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:59[ 533.660117] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:45:59[ 533.660122] ata2: irq_stat 0x00000040, connection status changed 02:45:59[ 533.660126] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:45:59[ 533.660132] ata2: hard resetting link 02:45:59[ 533.660141] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:45:59[ 533.660143] ata1: irq_stat 0x00000040, connection status changed 02:45:59[ 533.660147] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:45:59[ 533.660151] ata1: hard resetting link 02:46:00[ 534.412536] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00[ 534.412562] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00[ 534.416768] ata2.00: configured for UDMA/133 02:46:00[ 534.416777] ata2: EH complete 02:46:00[ 534.431396] ata1.00: configured for UDMA/133 02:46:00[ 534.431401] ata1: EH complete 02:46:03[ 537.384649] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:03[ 537.504214] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:03[ 537.585992] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:46:03[ 537.585996] ata1: irq_stat 0x00000040, connection status changed 02:46:03[ 537.585999] ata1: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:46:03[ 537.586002] ata1: hard resetting link 02:46:03[ 537.586028] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen t4 02:46:03[ 537.586030] ata2: irq_stat 0x00000040, connection status changed 02:46:03[ 537.586033] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:46:03[ 537.586036] ata2: hard resetting link 02:46:04[ 538.330147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04[ 538.330168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04[ 538.334389] ata2.00: configured for UDMA/133 02:46:04[ 538.334398] ata2: EH complete 02:46:04[ 538.343511] ata1.00: configured for UDMA/133 02:46:04[ 538.343519] ata1: EH complete 02:46:04[ 538.456413] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:04[ 538.459404] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:04[ 538.540138] ata1.00: limiting speed to UDMA/100:PIO4 02:46:04[ 538.540144] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5850000 action 0xe frozen 02:46:04[ 538.540148] ata1: irq_stat 0x00000040, connection status changed 02:46:04[ 538.540153] ata1: SError: { PHYRdyChg CommWake LinkSeq TrStaTrns DevExch } 02:46:04[ 538.540159] ata1: hard resetting link 02:46:04[ 538.540202] ata2.00: limiting speed to UDMA/100:PIO4 02:46:04[ 538.540207] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5950000 action 0xe frozen 02:46:04[ 538.540211] ata2: irq_stat 0x00000040, connection status changed 02:46:04[ 538.540215] ata2: SError: { PHYRdyChg CommWake Dispar LinkSeq TrStaTrns DevExch } 02:46:04[ 538.540220] ata2: hard resetting link 02:46:05[ 539.290054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05[ 539.290041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05[ 539.294100] ata2.00: configured for UDMA/100 02:46:05[ 539.294106] ata2: EH complete 02:46:05[ 539.314125] ata1.00: configured for UDMA/100 02:46:05[ 539.314132] ------------[ cut here ]------------ 02:46:05[ 539.314140] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:05[ 539.314144] Hardware name: MacBookPro5,3 02:46:05[ 539.314146] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:05[ 539.314221] Pid: 202, comm: scsi_eh_0 Tainted: P 2.6.35-25-generic #44-Ubuntu 02:46:05[ 539.314224] Call Trace: 02:46:05[ 539.314233] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:05[ 539.314237] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:05[ 539.314242] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:05[ 539.314246] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:05[ 539.314256] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:05[ 539.314261] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:05[ 539.314266] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:05[ 539.314270] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:05[ 539.314275] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:05[ 539.314280] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:05[ 539.314284] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:05[ 539.314288] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:05[ 539.314291] ---[ end trace 76dbffc2d5d49d9b ]--- 02:46:05[ 539.314296] ata1: EH complete 02:46:12[ 547.040091] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen 02:46:12[ 547.040098] ata1.00: failed command: IDENTIFY DEVICE 02:46:12[ 547.040106] ata1.00: cmd ec/00:00:00:00:00/00:00:00:00:00/40 tag 0 pio 512 in 02:46:12[ 547.040108] res 40/00:01:00:00:00/00:00:00:00:00/e0 Emask 0x4 (timeout) 02:46:12[ 547.040111] ata1.00: status: { DRDY } 02:46:12[ 547.040117] ata1: hard resetting link 02:46:13[ 547.390144] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:13[ 547.408430] ata1.00: configured for UDMA/100 02:46:13[ 547.408438] ------------[ cut here ]------------ 02:46:13[ 547.408447] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:13[ 547.408451] Hardware name: MacBookPro5,3 02:46:13[ 547.408453] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:13[ 547.408528] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 02:46:13[ 547.408531] Call Trace: 02:46:13[ 547.408540] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:13[ 547.408544] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:13[ 547.408549] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:13[ 547.408553] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:13[ 547.408563] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:13[ 547.408567] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:13[ 547.408572] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:13[ 547.408577] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:13[ 547.408582] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:13[ 547.408587] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:13[ 547.408591] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:13[ 547.408595] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:13[ 547.408598] ---[ end trace 76dbffc2d5d49d9c ]--- 02:46:13[ 547.408620] ata1: EH complete 02:46:13[ 547.562470] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:13[ 547.671380] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:13[ 547.738198] ata1.00: limiting speed to UDMA/33:PIO4 02:46:13[ 547.738204] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:13[ 547.738208] ata1: irq_stat 0x00000040, connection status changed 02:46:13[ 547.738212] ata1: SError: { LinkSeq TrStaTrns DevExch } 02:46:13[ 547.738218] ata1: hard resetting link 02:46:13[ 547.738262] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5900000 action 0xe frozen t4 02:46:13[ 547.738265] ata2: irq_stat 0x00000040, connection status changed 02:46:13[ 547.738269] ata2: SError: { Dispar LinkSeq TrStaTrns DevExch } 02:46:13[ 547.738274] ata2: hard resetting link 02:46:14[ 548.482561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14[ 548.484083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14[ 548.486809] ata2.00: configured for UDMA/100 02:46:14[ 548.486818] ata2: EH complete 02:46:14[ 548.498998] ata1.00: configured for UDMA/33 02:46:14[ 548.499004] ata1: EH complete 02:46:18[ 552.410499] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:18[ 552.522521] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:18[ 552.529674] ata1: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:18[ 552.529678] ata1: irq_stat 0x00000040, connection status changed 02:46:18[ 552.529680] ata1: SError: { LinkSeq TrStaTrns DevExch } 02:46:18[ 552.529684] ata1: hard resetting link 02:46:18[ 552.529716] ata2: exception Emask 0x10 SAct 0x0 SErr 0x5800000 action 0xe frozen t4 02:46:18[ 552.529718] ata2: irq_stat 0x00000040, connection status changed 02:46:18[ 552.529720] ata2: SError: { LinkSeq TrStaTrns DevExch } 02:46:18[ 552.529723] ata2: hard resetting link 02:46:19[ 553.280059] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19[ 553.280068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19[ 553.284141] ata2.00: configured for UDMA/100 02:46:19[ 553.284150] ata2: EH complete 02:46:19[ 553.301629] ata1.00: configured for UDMA/33 02:46:19[ 553.301637] ata1: EH complete

  Read the article

• XML transform element appearing in wrong place in document

  - by Mike

  I am having some problems with an XML transform and need some help. The stylesheet should iterate through all suffix elements and place the contents without the suffix tag next to the last text node within its first ancestor quote-block element (see desired ouput). It works when only a single suffix is present, but not when 2 are present, when 2 are present it places both suffixes next to each other in the last text node of the first quote-block. Any ideas? I have tried limiting the selections to ancestor::quote-block[1] in various places but that doesn't have the desired effect. Source XML <paragraph> <para> <quote-block> <list prefix-rules="specified"> <item prefix="“B42"> <para id="0a84d149-91b7-4012-ac6d-9f4eb8ed6c37">In June 2000, EME and EWS reached an agreement to negotiate towards a direct contract for coal haulage by rail (on a DIY basis), which would replace the previous indirect E2E arrangements that EME had in place with ECSL. An internal EWS e-mail noted: <quote-block> <quote-para>‘We did the deal with Edison Mission yesterday morning for LBT-Fiddlers @ £[…]/tonne as agreed. This rate until 16th September pending a contract.</quote-para> <quote-para><emphasis strength="strong">Enron are now off our hands so far as Edison are concerned. The Enron flows we have left are to British Energy’s station at Eggborough; from Immingham, Redcar and Hull</emphasis>. Also to Enron’s own power station at Wilton – 250,000 tonnes/year. I think we are stuck Enron [sic] on the Eggborough traffic until next April when British Energy will, hopefully take over their own coal procurement. <emphasis strength="strong">But we have got them out of Fiddlers Ferry and Ferrybridge – a big step forward</emphasis>.’</quote-para> <suffix>(Emphasis added.)</suffix> </quote-block> </para> </item> <item prefix="B43"> <para id="d64a5a72-0a02-476f-9a7b-7c07bbc93a8a">This e-mail is evidence of both EWS’s intent and, indeed, its success in stopping ECSL from carrying out indirect supplies to EME, one of the new generating companies.”</para> </item> </list> <suffix>(emphasis in original)</suffix> </quote-block> </para> </paragraph> Stylesheet <xsl:stylesheet xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:xs="http://www.w3.org/2001/XMLSchema" xmlns="http://xml.sm.com/schema/cases/report" xmlns:sm="http://xml.sm.com/functions" xmlns:saxon="http://saxon.sf.net/" xpath-default-namespace="http://sm.com/schema/cases/report" exclude-result-prefixes="xs sm" version="2.0"> <xsl:output method="xml" indent="no"/> <xsl:template match="/"> <xsl:apply-templates/> </xsl:template> <xsl:template match="*"> <xsl:copy> <xsl:copy-of select="@*"/> <xsl:apply-templates/> </xsl:copy> </xsl:template> <!-- Match quote-blocks with open or close attributes. --> <xsl:template match="*[*:quote-block and descendant::*:suffix]"> <xsl:call-template name="process-quote-block"/> </xsl:template> <!-- Match inline quote with open or close attributes --> <xsl:template match="*[*:quote and descendant::*:suffix]"> <xsl:call-template name="process-quote-block"/> </xsl:template> <!-- Process the quote block --> <xsl:template name="process-quote-block"> <xsl:variable name="quoteBlockCopy"> <xsl:copy-of select="."/> </xsl:variable> <xsl:apply-templates select="$quoteBlockCopy" mode="append-suffix"> <xsl:with-param name="suffix" select="sm:get-suffix-note(.)"/> <xsl:with-param name="end-node" select="sm:get-last-text-node($quoteBlockCopy)"/> </xsl:apply-templates> </xsl:template> <!-- Match quote-blocks with open or close attributes. --> <xsl:template match="*[*:quote-block and descendant::*:suffix][ancestor::*:quote-block[1]]" mode="create-copy"> <xsl:call-template name="process-quote-block"/> </xsl:template> <!-- Match inline quote with open or close attributes --> <xsl:template match="*[*:quote and descendant::*:suffix]" mode="create-copy"> <xsl:call-template name="process-quote-block"/> </xsl:template> <!-- This will match all elements. Just copy and pass through the parameters. --> <xsl:template match="*" mode="append-suffix"> <xsl:param name="suffix"/> <xsl:param name="end-node"/> <xsl:copy> <xsl:copy-of select="@*"/> <xsl:apply-templates mode="append-suffix"> <xsl:with-param name="suffix" select="$suffix"/> <xsl:with-param name="end-node" select="$end-node"/> </xsl:apply-templates> </xsl:copy> </xsl:template> <!-- Apply the text node to the content. If the node is equal to the last node then append the descendants of suffix --> <xsl:template match="text()[normalize-space() != '']" mode="append-suffix"> <xsl:param name="suffix"/> <xsl:param name="end-node"/> <xsl:choose> <xsl:when test="count(. | $end-node) = 1"> <xsl:value-of select="."/> <xsl:apply-templates select="$suffix"/> </xsl:when> <xsl:otherwise> <!-- Or maybe neither. --> <xsl:value-of select="."/> </xsl:otherwise> </xsl:choose> </xsl:template> <!-- Dont copy suffix as --> <xsl:template match="*:suffix" mode="append-suffix"/> <xsl:function name="sm:get-suffix-note"> <xsl:param name="node"/> <xsl:sequence select="$node/descendant::*:suffix/node()"/> </xsl:function> <xsl:function name="sm:get-last-text-node"> <!-- Finds last non-empty text() node, ignoring <suffix> elements that are a child of this specific quote-block. --> <xsl:param name="node"/> <xsl:sequence select="reverse($node//text()[not(ancestor::*:suffix) and normalize-space() != ''])[1]"/> </xsl:function> </xsl:stylesheet> Current Output XML <paragraph> <para> <quote-block> <list prefix-rules="specified"> <item prefix="“B42"> <para id="0a84d149-91b7-4012-ac6d-9f4eb8ed6c37">In June 2000, EME and EWS reached an agreement to negotiate towards a direct contract for coal haulage by rail (on a DIY basis), which would replace the previous indirect E2E arrangements that EME had in place with ECSL. An internal EWS e-mail noted: <quote-block> <quote-para>‘We did the deal with Edison Mission yesterday morning for LBT-Fiddlers @ £[…]/tonne as agreed. This rate until 16th September pending a contract.</quote-para> <quote-para><emphasis strength="strong">Enron are now off our hands so far as Edison are concerned. The Enron flows we have left are to British Energy’s station at Eggborough; from Immingham, Redcar and Hull</emphasis>. Also to Enron’s own power station at Wilton – 250,000 tonnes/year. I think we are stuck Enron [sic] on the Eggborough traffic until next April when British Energy will, hopefully take over their own coal procurement. <emphasis strength="strong">But we have got them out of Fiddlers Ferry and Ferrybridge – a big step forward</emphasis>.’</quote-para> </quote-block> </para> </item> <item prefix="B43"> <para id="d64a5a72-0a02-476f-9a7b-7c07bbc93a8a">This e-mail is evidence of both EWS’s intent and, indeed, its success in stopping ECSL from carrying out indirect supplies to EME, one of the new generating companies.”(Emphasis added.)(emphasis in original)</para> </item> </list> </quote-block> </para> </paragraph> Desired Ouput <paragraph> <para> <quote-block> <list prefix-rules="specified"> <item prefix="“B42"> <para id="0a84d149-91b7-4012-ac6d-9f4eb8ed6c37">In June 2000, EME and EWS reached an agreement to negotiate towards a direct contract for coal haulage by rail (on a DIY basis), which would replace the previous indirect E2E arrangements that EME had in place with ECSL. An internal EWS e-mail noted: <quote-block> <quote-para>‘We did the deal with Edison Mission yesterday morning for LBT-Fiddlers @ £[…]/tonne as agreed. This rate until 16th September pending a contract.</quote-para> <quote-para><emphasis strength="strong">Enron are now off our hands so far as Edison are concerned. The Enron flows we have left are to British Energy’s station at Eggborough; from Immingham, Redcar and Hull</emphasis>. Also to Enron’s own power station at Wilton – 250,000 tonnes/year. I think we are stuck Enron [sic] on the Eggborough traffic until next April when British Energy will, hopefully take over their own coal procurement. <emphasis strength="strong">But we have got them out of Fiddlers Ferry and Ferrybridge – a big step forward</emphasis>.’(Emphasis added.)</quote-para> </quote-block> </para> </item> <item prefix="B43"> <para id="d64a5a72-0a02-476f-9a7b-7c07bbc93a8a">This e-mail is evidence of both EWS’s intent and, indeed, its success in stopping ECSL from carrying out indirect supplies to EME, one of the new generating companies.”(emphasis in original)</para> </item> </list> </quote-block> </para> </paragraph>

  Read the article

• l2tp / ipsec debian Openswan U2.6.38 does not connect

  - by locojay

  i am trying to get ipsec/l2tp running on a debian server with an iphone as a client but always get: Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [RFC 3947] method set to=115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: ignoring Vendor ID payload [FRAGMENTATION 80000000] Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [Dead Peer Detection] Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: responding to Main Mode from unknown peer <clientip> Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R1: sent MR1, expecting MI2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R2: sent MR2, expecting MI3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: Main mode peer ID is ID_IPV4_ADDR: '10.2.210.176' Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: switched from "L2TP-PSK-noNAT" to "L2TP-PSK-noNAT" Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: new NAT mapping for #20, was <clientip>:43598, now <clientip>:49826 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: the peer proposed: <public ip>/32:17/1701 -> 10.2.210.176/32:17/0 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: responding to Quick Mode proposal {msgid:311d3282} Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: us: 171.138.2.13<171.138.2.13>:17/1701 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: them: <clientip>[10.2.210.176]:17/61719 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x05e23c9a <0x216077a9 xfrm=AES_256-HMAC_SHA1 NATOA=10.2.210.176 NATD=<clientip>:49826 DPD=enabled} Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA(0x05e23c9a) payload: deleting IPSEC State #21 Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA payload: deleting ISAKMP State #20 Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip>: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:27 vpn pluto[22711]: packet from <clientip>:49826: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: ERROR: asynchronous network error report on eth0 (sport=4500) for message to <clientip> port 49826, complainant <clientip>: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] my setup looks like this verizon fios actiontec -- DMZ-- ddwrt router -- debian xen instance actiontec : 192.168.1.1 ddwrt: 171.138.2.1 debian xen server: 171.138.2.13 forwarded udp 500, 4500, 1701 on ddwrt to debian xen instance. vpn passthrough is enabled /etc/ipsec.conf config setup dumpdir=/var/run/pluto/ nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:25.0.0.0/8,%v6:fd00::/8,%v6:fe80::/10,%v4:!171.138.2.0/24,%v4:!192.168.1.0/24 protostack=netkey # Add connections here conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Apple iOS doesn't send delete notify so we need dead peer detection # to detect vanishing clients dpddelay=30 dpdtimeout=120 dpdaction=clear # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=171.138.2.13 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "%any" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port. rightprotoport=17/%any #force all to be nat'ed. because of ios conn passthrough-for-non-l2tp type=passthrough left=171.138.2.13 leftnexthop=171.138.2.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/xl2tp/xl2tp.conf [global] ipsec saref = no listen-addr = 171.138.2.13 ;port = 1701 ;debug network = yes ;debug tunnel = yes ;debug network = yes ;debug packet = yes [lns default] ip range = 171.138.2.231-171.138.2.239 local ip = 171.138.2.13 assign ip = yes require chap = no refuse pap = no require authentication = no ;name = OpenswanVPN ppp debug = yes pppoptfile = /etc/ppp/options.xlt2tpd lenght bit = yes /etc/ppp/options.xl2tpd ;require-mschap-v2 pcp-accept-local ipcp-accept-local ipcp-accept-remote ;ms-dns 171.138.2.1 ms-dns 192.168.1.1 ms-dns 8.8.8.8 name l2tpd noccp auth crtscts idle 1800 mtu 1410 mru 1410 lock proxyarp connect-delay 5000 debug dump logfd 2 logfile /var/log/xl2tpd.log ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.0.0-1-amd64 (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Two or more interfaces found, checking IP forwarding [FAILED] Checking NAT and MASQUERADEing [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] The failed can be ignored i guess since cat /proc/sys/net/ipv4/ip_forward returns 1 any help would be much appreciated as i don't have any idea why this is not working

  Read the article

• How can I block a specific type of DDoS attack?

  - by Mark

  My site is being attacked and is using up all the RAM. I looked at the Apache logs and every malicious hit seems to simply be a POST request on /, which is never required by a normal user. So I thought and wondered if there's any sort of solution or utility that will monitor my Apache logs and block every IP that performs a POST request on the site root. I'm not familiar with DDoS protection and searching didn't seem to give me an answer, so I came here. Thanks. Example logs: 103.3.221.202 - - [30/Sep/2012:16:02:03 +0000] "POST / HTTP/1.1" 302 485 "-" "Mozilla/5.0 (iPad; CPU OS 5_1_1 like Mac OS X) AppleWebKit/534.46 (KHTML, like Gecko) Version/5.1 Mobile/9B206 Safari/7534.48.3" 122.72.80.100 - - [30/Sep/2012:16:02:03 +0000] "POST / HTTP/1.1" 302 485 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_4) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11" 122.72.28.15 - - [30/Sep/2012:16:02:04 +0000] "POST / HTTP/1.1" 302 485 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; SV1; .NET CLR 2.0.50727)" 210.75.120.5 - - [30/Sep/2012:16:02:04 +0000] "POST / HTTP/1.1" 302 485 "-" "Mozilla/5.0 (Windows NT 6.1; rv:12.0) Gecko/20100101 Firefox/12.0" 122.96.59.103 - - [30/Sep/2012:16:02:04 +0000] "POST / HTTP/1.1" 302 485 "-" "Mozilla/5.0 (Linux; U; Android 2.2; fr-fr; Desire_A8181 Build/FRF91) App3leWebKit/53.1 (KHTML, like Gecko) Version/4.0 Mobile Safari/533.1" 122.96.59.103 - - [30/Sep/2012:16:02:04 +0000] "POST / HTTP/1.1" 302 485 "-" "Mozilla/5.0 (Linux; U; Android 2.2; fr-fr; Desire_A8181 Build/FRF91) App3leWebKit/53.1 (KHTML, like Gecko) Version/4.0 Mobile Safari/533.1" 122.72.124.3 - - [30/Sep/2012:16:02:04 +0000] "POST / HTTP/1.1" 302 485 "-" "Mozilla/5.0 (X11; Ubuntu; Linux i686; rv:13.0) Gecko/20100101 Firefox/13.0.1" 122.72.112.148 - - [30/Sep/2012:16:02:04 +0000] "POST / HTTP/1.1" 302 485 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10.7; rv:13.0) Gecko/20100101 Firefox/13.0.1" 190.39.210.26 - - [30/Sep/2012:16:02:04 +0000] "POST / HTTP/1.0" 302 485 "-" "Mozilla/5.0 (Windows NT 6.0; rv:13.0) Gecko/20100101 Firefox/13.0.1" 210.213.245.230 - - [30/Sep/2012:16:02:04 +0000] "POST / HTTP/1.0" 302 485 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; SV1; .NET CLR 2.0.50727)" 101.44.1.25 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (iPhone; CPU iPhone OS 5_1_1 like Mac OS X) AppleWebKit/534.46 (KHTML, like Gecko) Version/5.1 Mobile/9B206 Safari/7534.48.3" 101.44.1.28 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1; rv:13.0) Gecko/20100101 Firefox/13.0.1" 101.44.1.28 - - [30/Sep/2012:16:02:14 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1; rv:13.0) Gecko/20100101 Firefox/13.0.1" 103.3.221.202 - - [30/Sep/2012:16:02:13 +0000] "POST / HTTP/1.1" 302 466 "-" "Mozilla/5.0 (iPad; CPU OS 5_1_1 like Mac OS X) AppleWebKit/534.46 (KHTML, like Gecko) Version/5.1 Mobile/9B206 Safari/7534.48.3" 211.161.152.104 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)" 101.44.1.25 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11" 101.44.1.25 - - [30/Sep/2012:16:02:11 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11" 211.161.152.105 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.2) Gecko/20100115 Firefox/3.6" 211.161.152.105 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; MRA 5.8 (build 4157); .NET CLR 2.0.50727; AskTbPTV/5.11.3.15590)" 211.161.152.105 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; MRA 5.8 (build 4157); .NET CLR 2.0.50727; AskTbPTV/5.11.3.15590)" 101.44.1.25 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11" 101.44.1.25 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (iPhone; CPU iPhone OS 5_1_1 like Mac OS X) AppleWebKit/534.46 (KHTML, like Gecko) Version/5.1 Mobile/9B206 Safari/7534.48.3" 211.161.152.108 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (iPad; CPU OS 5_1_1 like Mac OS X) AppleWebKit/534.46 (KHTML, like Gecko) Version/5.1 Mobile/9B206 Safari/7534.48.3" 101.44.1.28 - - [30/Sep/2012:16:02:13 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1; rv:13.0) Gecko/20100101 Firefox/13.0.1" 211.161.152.106 - - [30/Sep/2012:16:02:11 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1; rv:5.0.1) Gecko/20100101 Firefox/5.0.1" 103.3.221.202 - - [30/Sep/2012:16:02:13 +0000] "POST / HTTP/1.1" 302 466 "-" "Mozilla/5.0 (iPad; CPU OS 5_1_1 like Mac OS X) AppleWebKit/534.46 (KHTML, like Gecko) Version/5.1 Mobile/9B206 Safari/7534.48.3" 101.44.1.28 - - [30/Sep/2012:16:02:11 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1; rv:13.0) Gecko/20100101 Firefox/13.0.1" 211.161.152.105 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; MRA 5.8 (build 4157); .NET CLR 2.0.50727; AskTbPTV/5.11.3.15590)" 211.161.152.104 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)" 211.161.152.104 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1)" 211.161.152.105 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US; rv:1.9.2) Gecko/20100115 Firefox/3.6" 101.44.1.25 - - [30/Sep/2012:16:02:10 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11" 122.72.124.2 - - [30/Sep/2012:16:02:17 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1; rv:13.0) Gecko/20100101 Firefox/13.0.1" 122.72.124.2 - - [30/Sep/2012:16:02:11 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1; rv:13.0) Gecko/20100101 Firefox/13.0.1" 122.72.124.2 - - [30/Sep/2012:16:02:17 +0000] "POST / HTTP/1.1" 302 522 "-" "Mozilla/5.0 (Windows NT 5.1; rv:13.0) Gecko/20100101 Firefox/13.0.1" 210.213.245.230 - - [30/Sep/2012:16:02:12 +0000] "POST / HTTP/1.0" 302 522 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; SV1; .NET CLR 2.0.50727)" iptables -L: Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination - bui@debian:~$ sudo iptables -I INPUT 1 -m string --algo bm --string 'Keep-Alive: 300' -j DROP iptables: No chain/target/match by that name. bui@debian:~$ sudo iptables -A INPUT -m string --algo bm --string 'Keep-Alive: 300' -j DROP iptables: No chain/target/match by that name.

  Read the article

• ProFTPd server on Ubuntu getting access denied message when successfully authenticated?

  - by exxoid

  I have a Ubuntu box with a ProFTPD 1.3.4a Server, when I try to log in via my FTP Client I cannot do anything as it does not allow me to list directories; I have tried logging in as root and as a regular user and tried accessing different paths within the FTP Server. The error I get in my FTP Client is: Status: Retrieving directory listing... Command: CDUP Response: 250 CDUP command successful Command: PWD Response: 257 "/var" is the current directory Command: PASV Response: 227 Entering Passive Mode (172,16,4,22,237,205). Command: MLSD Response: 550 Access is denied. Error: Failed to retrieve directory listing Any idea? Here is the config of my proftpd: # # /etc/proftpd/proftpd.conf -- This is a basic ProFTPD configuration file. # To really apply changes, reload proftpd after modifications, if # it runs in daemon mode. It is not required in inetd/xinetd mode. # # Includes DSO modules Include /etc/proftpd/modules.conf # Set off to disable IPv6 support which is annoying on IPv4 only boxes. UseIPv6 off # If set on you can experience a longer connection delay in many cases. IdentLookups off ServerName "Drupal Intranet" ServerType standalone ServerIdent on "FTP Server ready" DeferWelcome on # Set the user and group that the server runs as User nobody Group nogroup MultilineRFC2228 on DefaultServer on ShowSymlinks on TimeoutNoTransfer 600 TimeoutStalled 600 TimeoutIdle 1200 DisplayLogin welcome.msg DisplayChdir .message true ListOptions "-l" DenyFilter \*.*/ # Use this to jail all users in their homes # DefaultRoot ~ # Users require a valid shell listed in /etc/shells to login. # Use this directive to release that constrain. # RequireValidShell off # Port 21 is the standard FTP port. Port 21 # In some cases you have to specify passive ports range to by-pass # firewall limitations. Ephemeral ports can be used for that, but # feel free to use a more narrow range. # PassivePorts 49152 65534 # If your host was NATted, this option is useful in order to # allow passive tranfers to work. You have to use your public # address and opening the passive ports used on your firewall as well. # MasqueradeAddress 1.2.3.4 # This is useful for masquerading address with dynamic IPs: # refresh any configured MasqueradeAddress directives every 8 hours <IfModule mod_dynmasq.c> # DynMasqRefresh 28800 </IfModule> # To prevent DoS attacks, set the maximum number of child processes # to 30. If you need to allow more than 30 concurrent connections # at once, simply increase this value. Note that this ONLY works # in standalone mode, in inetd mode you should use an inetd server # that allows you to limit maximum number of processes per service # (such as xinetd) MaxInstances 30 # Set the user and group that the server normally runs at. # Umask 022 is a good standard umask to prevent new files and dirs # (second parm) from being group and world writable. Umask 022 022 # Normally, we want files to be overwriteable. AllowOverwrite on # Uncomment this if you are using NIS or LDAP via NSS to retrieve passwords: # PersistentPasswd off # This is required to use both PAM-based authentication and local passwords AuthPAMConfig proftpd AuthOrder mod_auth_pam.c* mod_auth_unix.c # Be warned: use of this directive impacts CPU average load! # Uncomment this if you like to see progress and transfer rate with ftpwho # in downloads. That is not needed for uploads rates. # UseSendFile off TransferLog /var/log/proftpd/xferlog SystemLog /var/log/proftpd/proftpd.log # Logging onto /var/log/lastlog is enabled but set to off by default #UseLastlog on # In order to keep log file dates consistent after chroot, use timezone info # from /etc/localtime. If this is not set, and proftpd is configured to # chroot (e.g. DefaultRoot or <Anonymous>), it will use the non-daylight # savings timezone regardless of whether DST is in effect. #SetEnv TZ :/etc/localtime <IfModule mod_quotatab.c> QuotaEngine off </IfModule> <IfModule mod_ratio.c> Ratios off </IfModule> # Delay engine reduces impact of the so-called Timing Attack described in # http://www.securityfocus.com/bid/11430/discuss # It is on by default. <IfModule mod_delay.c> DelayEngine on </IfModule> <IfModule mod_ctrls.c> ControlsEngine off ControlsMaxClients 2 ControlsLog /var/log/proftpd/controls.log ControlsInterval 5 ControlsSocket /var/run/proftpd/proftpd.sock </IfModule> <IfModule mod_ctrls_admin.c> AdminControlsEngine off </IfModule> # # Alternative authentication frameworks # #Include /etc/proftpd/ldap.conf #Include /etc/proftpd/sql.conf # # This is used for FTPS connections # #Include /etc/proftpd/tls.conf # # Useful to keep VirtualHost/VirtualRoot directives separated # #Include /etc/proftpd/virtuals.con # A basic anonymous configuration, no upload directories. # <Anonymous ~ftp> # User ftp # Group nogroup # # We want clients to be able to login with "anonymous" as well as "ftp" # UserAlias anonymous ftp # # Cosmetic changes, all files belongs to ftp user # DirFakeUser on ftp # DirFakeGroup on ftp # # RequireValidShell off # # # Limit the maximum number of anonymous logins # MaxClients 10 # # # We want 'welcome.msg' displayed at login, and '.message' displayed # # in each newly chdired directory. # DisplayLogin welcome.msg # DisplayChdir .message # # # Limit WRITE everywhere in the anonymous chroot # <Directory *> # <Limit WRITE> # DenyAll # </Limit> # </Directory> # # # Uncomment this if you're brave. # # <Directory incoming> # # # Umask 022 is a good standard umask to prevent new files and dirs # # # (second parm) from being group and world writable. # # Umask 022 022 # # <Limit READ WRITE> # # DenyAll # # </Limit> # # <Limit STOR> # # AllowAll # # </Limit> # # </Directory> # # </Anonymous> # Include other custom configuration files Include /etc/proftpd/conf.d/ UseReverseDNS off <Global> RootLogin on UseFtpUsers on ServerIdent on DefaultChdir /var/www DeleteAbortedStores on LoginPasswordPrompt on AccessGrantMsg "You have been authenticated successfully." </Global> Any idea what could be wrong? Thanks for your help!

  Read the article

• Installing Lubuntu 14.04.1 forcepae fails

  - by Rantanplan

  I tried to install Lubuntu 14.04.1 from a CD. First, I chose Try Lubuntu without installing which gave: ERROR: PAE is disabled on this Pentium M (PAE can potentially be enabled with kernel parameter "forcepae" ... Following the description on https://help.ubuntu.com/community/PAE, I used forcepae and tried Try Lubuntu without installing again. That worked fine. dmesg | grep -i pae showed: [ 0.000000] Kernel command line: file=/cdrom/preseed/lubuntu.seed boot=casper initrd=/casper/initrd.lz quiet splash -- forcepae [ 0.008118] PAE forced! On the live-CD session, I tried installing Lubuntu double clicking on the install button on the desktop. Here, the CD starts running but then stops running and nothing happens. Next, I rebooted and tried installing Lubuntu directly from the boot menu screen using forcepae again. After a while, I receive the following error message: The installer encountered an unrecoverable error. A desktop session will now be run so that you may investigate the problem or try installing again. Hitting Enter brings me to the desktop. For what errors should I search? And how? Finally, I rebooted once more and tried Check disc for defects with forcepae option; no errors have been found. Now, I am wondering how to find the error or whether it would be better to follow advice c in https://help.ubuntu.com/community/PAE: "Move the hard disk to a computer on which the processor has PAE capability and PAE flag (that is, almost everything else than a Banias). Install the system as usual but don't add restricted drivers. After the install move the disk back." Thanks for some hints! Perhaps some of the following can help: On Lubuntu 12.04: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr mce cx8 mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe up bts est tm2 bogomips : 1284.76 clflush size : 64 cache_alignment : 64 address sizes : 32 bits physical, 32 bits virtual power management: uname -a Linux humboldt 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:45:51 UTC 2014 i686 i686 i386 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.5 LTS Release: 12.04 Codename: precise cpuid eax in eax ebx ecx edx 00000000 00000002 756e6547 6c65746e 49656e69 00000001 000006d6 00000816 00000180 afe9f9bf 00000002 02b3b001 000000f0 00000000 2c04307d 80000000 80000004 00000000 00000000 00000000 80000001 00000000 00000000 00000000 00000000 80000002 20202020 20202020 65746e49 2952286c 80000003 6e655020 6d756974 20295228 7270204d 80000004 7365636f 20726f73 30352e31 007a4847 Vendor ID: "GenuineIntel"; CPUID level 2 Intel-specific functions: Version 000006d6: Type 0 - Original OEM Family 6 - Pentium Pro Model 13 - Stepping 6 Reserved 0 Brand index: 22 [not in table] Extended brand string: " Intel(R) Pentium(R) M processor 1.50GHz" CLFLUSH instruction cache line size: 8 Feature flags afe9f9bf: FPU Floating Point Unit VME Virtual 8086 Mode Enhancements DE Debugging Extensions PSE Page Size Extensions TSC Time Stamp Counter MSR Model Specific Registers MCE Machine Check Exception CX8 COMPXCHG8B Instruction SEP Fast System Call MTRR Memory Type Range Registers PGE PTE Global Flag MCA Machine Check Architecture CMOV Conditional Move and Compare Instructions FGPAT Page Attribute Table CLFSH CFLUSH instruction DS Debug store ACPI Thermal Monitor and Clock Ctrl MMX MMX instruction set FXSR Fast FP/MMX Streaming SIMD Extensions save/restore SSE Streaming SIMD Extensions instruction set SSE2 SSE2 extensions SS Self Snoop TM Thermal monitor 31 reserved TLB and cache info: b0: unknown TLB/cache descriptor b3: unknown TLB/cache descriptor 02: Instruction TLB: 4MB pages, 4-way set assoc, 2 entries f0: unknown TLB/cache descriptor 7d: unknown TLB/cache descriptor 30: unknown TLB/cache descriptor 04: Data TLB: 4MB pages, 4-way set assoc, 8 entries 2c: unknown TLB/cache descriptor On Lubuntu 14.04.1 live-CD with forcepae: cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 13 model name : Intel(R) Pentium(R) M processor 1.50GHz stepping : 6 microcode : 0x17 cpu MHz : 600.000 cache size : 2048 KB physical id : 0 siblings : 1 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fdiv_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca cmov clflush dts acpi mmx fxsr sse sse2 ss tm pbe bts est tm2 bogomips : 1284.68 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 32 bits virtual power management: uname -a Linux lubuntu 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:12 UTC 2014 i686 i686 i686 GNU/Linux lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04.1 LTS Release: 14.04 Codename: trusty cpuid CPU 0: vendor_id = "GenuineIntel" version information (1/eax): processor type = primary processor (0) family = Intel Pentium Pro/II/III/Celeron/Core/Core 2/Atom, AMD Athlon/Duron, Cyrix M2, VIA C3 (6) model = 0xd (13) stepping id = 0x6 (6) extended family = 0x0 (0) extended model = 0x0 (0) (simple synth) = Intel Pentium M (Dothan B1) / Celeron M (Dothan B1), 90nm miscellaneous (1/ebx): process local APIC physical ID = 0x0 (0) cpu count = 0x0 (0) CLFLUSH line size = 0x8 (8) brand index = 0x16 (22) brand id = 0x16 (22): Intel Pentium M, .13um feature information (1/edx): x87 FPU on chip = true virtual-8086 mode enhancement = true debugging extensions = true page size extensions = true time stamp counter = true RDMSR and WRMSR support = true physical address extensions = false machine check exception = true CMPXCHG8B inst. = true APIC on chip = false SYSENTER and SYSEXIT = true memory type range registers = true PTE global bit = true machine check architecture = true conditional move/compare instruction = true page attribute table = true page size extension = false processor serial number = false CLFLUSH instruction = true debug store = true thermal monitor and clock ctrl = true MMX Technology = true FXSAVE/FXRSTOR = true SSE extensions = true SSE2 extensions = true self snoop = true hyper-threading / multi-core supported = false therm. monitor = true IA64 = false pending break event = true feature information (1/ecx): PNI/SSE3: Prescott New Instructions = false PCLMULDQ instruction = false 64-bit debug store = false MONITOR/MWAIT = false CPL-qualified debug store = false VMX: virtual machine extensions = false SMX: safer mode extensions = false Enhanced Intel SpeedStep Technology = true thermal monitor 2 = true SSSE3 extensions = false context ID: adaptive or shared L1 data = false FMA instruction = false CMPXCHG16B instruction = false xTPR disable = false perfmon and debug = false process context identifiers = false direct cache access = false SSE4.1 extensions = false SSE4.2 extensions = false extended xAPIC support = false MOVBE instruction = false POPCNT instruction = false time stamp counter deadline = false AES instruction = false XSAVE/XSTOR states = false OS-enabled XSAVE/XSTOR = false AVX: advanced vector extensions = false F16C half-precision convert instruction = false RDRAND instruction = false hypervisor guest status = false cache and TLB information (2): 0xb0: instruction TLB: 4K, 4-way, 128 entries 0xb3: data TLB: 4K, 4-way, 128 entries 0x02: instruction TLB: 4M pages, 4-way, 2 entries 0xf0: 64 byte prefetching 0x7d: L2 cache: 2M, 8-way, sectored, 64 byte lines 0x30: L1 cache: 32K, 8-way, 64 byte lines 0x04: data TLB: 4M pages, 4-way, 8 entries 0x2c: L1 data cache: 32K, 8-way, 64 byte lines extended feature flags (0x80000001/edx): SYSCALL and SYSRET instructions = false execution disable = false 1-GB large page support = false RDTSCP = false 64-bit extensions technology available = false Intel feature flags (0x80000001/ecx): LAHF/SAHF supported in 64-bit mode = false LZCNT advanced bit manipulation = false 3DNow! PREFETCH/PREFETCHW instructions = false brand = " Intel(R) Pentium(R) M processor 1.50GHz" (multi-processing synth): none (multi-processing method): Intel leaf 1 (synth) = Intel Pentium M (Dothan B1), 90nm

  Read the article

< Previous Page | 159 160 161 162 163 164 165 166 167 168 169 170  | Next Page >