Search Results

Search found 21317 results on 853 pages for 'address bar'.

Page 164/853 | < Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >

  • ifconfig ignores alias on IPv6

    - by Marten Lehmann
    When I add an IPv4 address for the interface eth0:0 with ifconfig, it is created correctly: ifconfig eth0:0 add 192.168.10.10 This can be verified by ifconfig or "ip a". When I add an IPv6 address however, ifconfig seems to ignore the alias of the interface: ifconfig eth0:0 add fc00::2/48 The address fc00::2/48 is added to eth0 then, not to eth0:0, no matter if eth0:0 previously exists with an IPv4 address or not. I'm doing this on CentOS 5 but I guess it is a general behaviour of ifconfig? Am I doing something wrong or is this by intention? I'm using separate aliases for interfaces very often and I hoped to use it for IPv6 as well. Kind regards Marten

    Read the article

  • MacBook can't use internet, but nslookup and ping both work

    - by Joel Coehoorn
    I have a user with a new high-end MacBook Pro that can't use the internet. He can connect to either our wired or wireless network and do things like browse file shares, but can get no further. When I brought the machine in for testing, I found that I could do an nslookup just fine, and I'm able to ping addresses returned by nslookup just fine. I'm even able to bring up web pages by entering the IP address into the address bar directly. However, when I try to ping the domain name rather than the IP address, it just sits there. So apparently I can either do name resolution or communicate with an address, but not both at the same time. Again, these symptoms occur on both the wired and wireless network. Other machines on our network, including a few other Macs, don't have this issue. Any ideas?

    Read the article

  • Enable Thumbnail Previews for Firefox in Windows 7 Taskbar

    - by Asian Angel
    Are you tired of waiting for the official activation of Taskbar Thumbnail Previews in Firefox? See how easy it is to enable them now with a simple about:config hack. Note: We have briefly covered this before but present it here in a more detailed format. Before For our example we opened all of the websites in the HTG Network in tabs… When hovering over the Firefox Icon in the Taskbar, you only see the one thumbnail. There are two things in particular to notice here: 1.) The Tab Bar for Firefox is displayed with all four tabs visible in the Thumbnail Preview  2.) The “Taskbar Icon” itself is displaying as singular with no “fanned edge” on the right side. Hack the About:Config Settings To get the Thumbnail Previews working you will need to make a modification in the about:config settings. Type about:config in the Address Bar and press Enter. Unless you have previously disabled the warning you will see this message after pressing Enter. Click on the I promise! Button to finish entering the settings. In the Filter Address Bar either type or copy and paste the following about:config entry: browser.taskbar.previews.enable After you enter that in, you should see the entry listing as shown here. At this point there are two methods that you can choose to alter the entry. The first method is to right click on the entry and select Toggle and the second method is to double click on the entry. Both work equally well…choose the method that you like best. Once the about:config entry has been changed, you will need to restart Firefox for it to take effect. After restarting Firefox on our system the Thumbnail Previews were definitely looking very nice. Notice that the Tab Bar is no longer displayed in the Thumbnail Previews. The Taskbar Icon also had a “fanned edge” indicating that multiple tabs were open. Conclusion If you are tired of waiting for Mozilla to officially activate Taskbar Thumbnail Previews in Firefox, then you can go ahead and start enjoying them now. For more great Firefox 3.6.x about:config hacks read our article here. Similar Articles Productive Geek Tips Vista Style Popup Previews for Firefox TabsDisable IE 8 Thumbnail Previews on Windows 7 TaskbarIncrease the size of Taskbar Preview Thumbnails in Windows 7Workaround for Vista Taskbar Thumbnail Previews Not Showing CorrectlyDisable Thumbnail Previews in Windows 7 or Vista Explorer TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Cool Looking Skins for Windows Media Player 12 Move the Mouse Pointer With Your Face Movement Using eViacam Boot Windows Faster With Boot Performance Diagnostics Create Ringtones For Your Android Phone With RingDroid Enhance Your Laptop’s Battery Life With These Tips Easily Search Food Recipes With Recipe Chimp

    Read the article

  • KVM machine does not start ssh, network is started, used to work

    - by lleto
    have been searching an pulling my hear out for the last 6 hours. I have a virtual machine that has been running fine for the last six months. I was happy ssh'ing into it and it was running a database and some small apps. Tonight ssh stopped working, so I decided to reboot the machine. I now have the following situation: virsh list --all states machine as running I can ping the machine and get a reply When I ssh to the machine I see "ssh: connect to host [myserver] port 22: Connection refused" nmap does not show port 22 as open I have tried to: - reboot the machine once more (no luck) - mount the filesystem and check /etc/ssh/sshd.conf (has not changed since working situation) - install virsh console, however this does not seem to work When I mount the fs directly using losetup the strange thing is that file dates seem to be frozen in /var/log/ around the time of the crash. If I look in /var/run/ I can see an sshd.pid, but the time is 6 hours ago (and numerous reboots). My virsh xml looks like this: <domain type='kvm' id='21'> <name>myserver</name> <uuid>09678c8d-a99b-1d18-a7af-88d027cc8f93</uuid> <memory>1048576</memory> <currentMemory>1048576</currentMemory> <vcpu>1</vcpu> <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>destroy</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/dev/disk01/myserver'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:e3:13:86'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target type='serial' port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes' listen='127.0.0.1'> <listen type='address' address='127.0.0.1'/> </graphics> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='apparmor' relabel='yes'> <label>libvirt-09678c8d-a99b-1d18-a7af-88d027cc8f93</label> <imagelabel>libvirt-09678c8d-a99b-1d18-a7af-88d027cc8f93</imagelabel> </seclabel> </domain> I'm sort of lost as to where I can look to get the machine up and running again. On the same instance of kvm I have another server running which is working fine. Both are Ubuntu 12.04. All help is welcome....

    Read the article

  • How to balance the root domain using NS records?

    - by Patrick McCurley
    I have two load balancers that balance incoming traffic across multiple data centers. These work fine. I can test them out by doing an 'nslookup mydomain.com xIP' I have now taken out DNS services with DYN.com to allow me to manage the DNS Zone file so that typing mydomain.com will ask my load balancers what the IP address is to resolve. Step 1 : the NS record for www. I set up A records (glue) for ns1 & ns2, then the corresponding NS record to delegate the DNS lookup to the balancers instead of DYN.com's nameservers. ns1.mydomain.com A [ip address of load balancer 1] ns2.mydomain.com A [ip address of load balancer 1] www.mydomain.com NS ns1.mydomain.com www.mydomain.com NS ns2.mydomain.com All is well - when I type www.mydomain.com, the requests get delegated to my load balancers who provide the IP address of the endpoint and the connect is made successfully. Step 2 : the NS record for root. This is where I run into problems. I need customers to be able to type 'mydomain.com' (without the www) and ALSO get delegated to the load balancers for the IP address. However - of the research I have done, and through the DYN control panel, it seems to be not allowed to provide an NS record for the root - as this overrides the default NS servers. How can i delegate both the root, and the www. to my load balancers?

    Read the article

  • How to configure Exchange Server with AutoReply that sends the reply only once?

    - by Abel
    If you configure Exchange Server 2007 for auto-reply on a public address, and the reply is sent to an address that also has auto-reply or out-of-office-auto-reply, then Exchange Server will receive a new message, same from-address, and will again send an auto-reply. This can go on forever and can potentially lead to a DoS situation. How can I prevent multiple sending of auto-reply to the same address, preferably in a given timeframe (to prevent legitimate multiple mails to be treated incorrectly), using Exchange Server 2007? Our XS hosting provider says it cannot be done, but that strikes me as odd.

    Read the article

  • what is ip 10.1.1.130 to which seems monitored by NT Kernel & System process on Windows 7?

    - by EndangeringSpecies
    I used netstat to see what is happening with network connections, and I see this weird ip address somehow listed together with PID 4 "NT Kernel & System", whatever that might be. Netstat describes it as a "local address" and there is no "foreign address" involved (btw, what are local and foreign addresses anyway?) In the column to the right there is neither "listening" nor "established" record, so no record at all there.

    Read the article

  • How can I forward ALL traffic over a site-to-site VPN on Cisco ASA?

    - by Scott Clements
    Hi There, I currently have two Cisco ASA 5100 routers. They are at different physical sites and are configured with a site-to-site VPN which is active and working. I can communicate with the subnets on either site from the other and both are connected to the internet, however I need to ensure that all the traffic at my remote site goes through this VPN to my site here. I know that the web traffic is doing so as a "tracert" confirms this, but I need to ensure that all other network traffic is being directed over this VPN to my network here. Here is my config for the ASA router at my remote site: hostname ciscoasa domain-name xxxxx enable password 78rl4MkMED8xiJ3g encrypted names ! interface Ethernet0/0 nameif NIACEDC security-level 100 ip address x.x.x.x 255.255.255.0 ! interface Ethernet0/1 description External Janet Connection nameif JANET security-level 0 ip address x.x.x.x 255.255.255.248 ! interface Ethernet0/2 shutdown no nameif security-level 100 no ip address ! interface Ethernet0/3 shutdown no nameif security-level 100 ip address dhcp setroute ! interface Management0/0 nameif management security-level 100 ip address 192.168.100.1 255.255.255.0 management-only ! passwd 2KFQnbNIdI.2KYOU encrypted ftp mode passive clock timezone GMT/BST 0 clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00 dns domain-lookup NIACEDC dns server-group DefaultDNS name-server 154.32.105.18 name-server 154.32.107.18 domain-name XXXX same-security-traffic permit inter-interface same-security-traffic permit intra-interface access-list ren_access_in extended permit ip any any access-list ren_access_in extended permit tcp any any access-list ren_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list NIACEDC_nat0_outbound extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list JANET_20_cryptomap extended permit ip 192.168.12.0 255.255.255.0 192.168.3.0 255.255.255.0 access-list NIACEDC_access_in extended permit ip any any access-list NIACEDC_access_in extended permit tcp any any access-list JANET_access_out extended permit ip any any access-list NIACEDC_access_out extended permit ip any any pager lines 24 logging enable logging asdm informational mtu NIACEDC 1500 mtu JANET 1500 mtu management 1500 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-522.bin no asdm history enable arp timeout 14400 nat-control global (NIACEDC) 1 interface global (JANET) 1 interface nat (NIACEDC) 0 access-list NIACEDC_nat0_outbound nat (NIACEDC) 1 192.168.12.0 255.255.255.0 access-group NIACEDC_access_in in interface NIACEDC access-group NIACEDC_access_out out interface NIACEDC access-group JANET_access_out out interface JANET route JANET 0.0.0.0 0.0.0.0 194.82.121.82 1 route JANET 0.0.0.0 0.0.0.0 192.168.3.248 tunneled timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout uauth 0:05:00 absolute http server enable http 192.168.12.0 255.255.255.0 NIACEDC http 192.168.100.0 255.255.255.0 management http 192.168.9.0 255.255.255.0 NIACEDC no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto map JANET_map 20 match address JANET_20_cryptomap crypto map JANET_map 20 set pfs crypto map JANET_map 20 set peer X.X.X.X crypto map JANET_map 20 set transform-set ESP-AES-256-SHA crypto map JANET_map interface JANET crypto isakmp enable JANET crypto isakmp policy 10 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 30 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 50 authentication pre-share encryption aes-256 hash sha group 5 lifetime 86400 tunnel-group X.X.X.X type ipsec-l2l tunnel-group X.X.X.X ipsec-attributes pre-shared-key * telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd address 192.168.100.2-192.168.100.254 management dhcpd enable management ! ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect http ! service-policy global_policy global prompt hostname context no asdm history enable Thanks in advance, Scott

    Read the article

  • VPN networking issue

    - by DuncanDavies
    I have 2 servers hosted in the cloud. One an application server, one a VPN server, both running Win2008. Both have a local IP address assigned by DHCP in different network subnets, 10.227.55.0 (VPN) and 10.231.5.0 (App Server). These servers can ping each other. My VPN client connects in to the VPN server (using a L2TP connection on a Win7 client). It is assigned an IP Address from the VPN server's static pool (the VPN server takes 192.168.100.1, the client is given 192.168.100.2). The client can ping both the 192.168.100.1 address of the VPN server, and its 'local' IP address (10.227.55.X). What the client can't do is ping the App Server. How can I configure routing so that my client can access the App Server, without hard-coding any of the DHCP IP addresses anywhere? thanks Duncan

    Read the article

  • Mac Websharing Off but Process Running

    - by benedict_w
    I have my mac setup to use php / mysql / apache via macports. Recently it has gone a bit pear shaped: it seems that the local mac versions of apache and mysql are running blocking the macports services: (48)Address already in use: make_sock: could not bind to address [::]:80 (48)Address already in use: make_sock: could not bind to address [::]:443 Web sharing in System preferences is off - How can I properly disable it? I tried turning it on an off again in System Preferences but it would not changed from off to on. Also if I kill the process it starts running again.

    Read the article

  • getting Internet connection sharing working in a slightly more complicated configuration

    - by tirichitirca t
    I have the following configuration: Computer A - Mac OSX 10.8.4, wireless & wired adapters Computer B - Windows 7 (64 bit), wireless & wired adapters, has internet connection via the wired adapter (ethernet) d-link wired/wireless router. Problem to solve: Connect from computer A to the internet through the wired connection of computer B. I tried the following: I set up a local network between A and B using the d-link router. The configuration is this: D-link router - 192.168.0.1 A - wired connection to the d-link router, static 192.168.0.101 (I could have used the wireless but I preferred the wired connection) B - wireless connection to the d-link router DHCP 192.168.0.102 (but I made sure it always gets the same address) B - wired connection to the internet using some address that begins with 10.x.y.z. In this configuration A can see B. I enabled ICS on the wired adapter of B. I set up the Gateway of A to point to B and DNS servers to point to the DNS servers specified for the 10.x.y.z address. It doesn't work, A goes only as far as B. It can ping the 10.x.y.z address of B though. I then found this article: http://terrybritton.com/windows-internet-connection-sharing-ics-not-working-with-linux-bridging-is-the-solution-916/. Terry is suggesting that a bridge should be defined on B between the two connections. I tried that but basically computer B is screwed as soon as I create the bridge. It can't connect to the internet anymore. It is as if the network bridge seems to think the traffic to the internet should go from the wired connection to the wireless and not the other way around. The other thing that puzzles me is the router itself. In general the router needs an internet address. In a normal configuration it is the router that gets the ip address and the internet traffic goes through the router. In my case I am not interested in that. So, any suggestions to get this working? I wouldn't shy away from using a commercial software but I would think windows 7 should allow me to do it. Thanks

    Read the article

  • Mac OS X Server 10.6.6 DNS not responding properly, get a "Truncated, retrying in TCP mode" for subdomain

    - by Eric Arseneau
    If I do an nslookup on youtube.com, no problem, if I do one with www.youtube.com, failure. See details below. [~] nslookup youtube.com Server: 192.168.1.1 Address: 192.168.1.1#53 Non-authoritative answer: Name: youtube.com Address: 74.125.127.93 Name: youtube.com Address: 74.125.47.93 Name: youtube.com Address: 74.125.95.93 [~] nslookup www.youtube.com ;; Truncated, retrying in TCP mode. ;; Connection to 192.168.1.1#53(192.168.1.1) for www.youtube.com failed: connection refused. If I do the same from a Windows machine its fine, its when I do it from a Mac workstation that I get the issue. I have rebooted, both server and workstation, I did a changeip, but nothing is working. Any recommendations?

    Read the article

  • Does not recognize usb sticks and drives

    - by Peter
    When connecting any usb stick to my thinkpad ubuntu 10.10 does not recognize them. I don't see anything on the desktop. the output of "dmesg | tail -n10" gives me: [ 1965.696388] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1965.884537] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.072503] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.260349] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.506227] usb 1-1: new high speed USB device using ehci_hcd and address 9 [ 1966.572375] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.760379] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1966.948358] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1967.136335] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 1967.325423] hub 1-0:1.0: unable to enumerate USB device on port 1 When connecting my usb scanner to the same port: [ 2008.480135] usb 1-1: new high speed USB device using ehci_hcd and address 65 [ 2008.548389] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2008.736786] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2008.924379] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.112348] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.300443] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.488536] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2009.732180] usb 1-1: new high speed USB device using ehci_hcd and address 71 [ 2014.796299] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 2018.000128] usb 2-1: new full speed USB device using uhci_hcd and address 3 And ubuntu 10.10 recognizes that scanner. So: What can i do to see my usb stick? BTW: on my other Thinkpad running fedora 14 it works perfectly... Cheers -Peter

    Read the article

  • USB keyboard stopped working in Ubuntu with error -71

    - by tapan
    I have a usb keyboard which was working perfectly till now (about a year since i have been regularly using ubuntu). It suddenly stopped working. It stopped working when I connected a USB HDD. Now the keyboard works randomly .. working for a while and then stops working for a longer time. Here is the dmesg output : [ 705.817076] usb 5-1: device not accepting address 8, error -71 [ 705.928032] usb 5-1: new low speed USB device using uhci_hcd and address 9 [ 706.336060] usb 5-1: device not accepting address 9, error -71 [ 706.448055] usb 5-1: new low speed USB device using uhci_hcd and address 10 [ 706.568044] usb 5-1: device descriptor read/64, error -71 [ 706.792049] usb 5-1: device descriptor read/64, error -71 [ 707.008060] usb 5-1: new low speed USB device using uhci_hcd and address 11 [ 707.128041] usb 5-1: device descriptor read/64, error -71 [ 707.352052] usb 5-1: device descriptor read/64, error -71 [ 707.456068] hub 5-0:1.0: unable to enumerate USB device on port 1 Based on the suggestions here i tried the following two things: echo -1 > /sys/module/usbcore/parameters/autosuspend echo Y > /sys/module/usbcore/parameters/old_scheme_first However, i am still facing the same problem. Can anyone help me out with this ? I'm using Ubuntu 10.04 Lucid Lynx.

    Read the article

  • SSIS Reporting Pack update

    - by jamiet
    Its been a while since I last posted anything in regard to SSIS Reporting Pack, the most recent release being on 27th May 2012, so here is a short update. There is still lots of work to do on SSIS Reporting Pack; lots more features to add, lots of performance work to be done, and a few bug fixes too. I have also been (fairly) hard at work on a framework to be used in conjunction with SSIS 2012 that I refer to as the Restart Framework (currently residing at http://ssisrestartframework.codeplex.com/). There is still much work to be done on the Restart Framework (not least some useful documentation on how to use it) which is why I haven’t mentioned it publicly before now although I am actively checking in changes. One thing I am considering is amalgamating the two projects into one; this would mean I could build a suite of reports that both work against the SSIS Catalog (what you currently know as “SSIS Reporting Pack”) and also against this Restart Framework thing. No decision has been made as yet though. There have been a number of bug reports and feature suggestions for SSIS Reporting Pack added to the Issue Tracker. Thank you to everyone that has submitted something, rest assured I am not going to ignore them forever; my time is at a premium right now unfortunately due to … well … life… so working on these items isn’t near the top of my priority list. Lastly, I am actively using SSIS Reporting Pack in a production environment right now and I’m happy to report that it is proving to be very useful. One of the reports that I have put a lot of time into is execution executable duration.rdl and its proving very adept at easily identifying bottlenecks in our SSIS 2012 executions: The report allows you to browse through the hierarchy of executables in each execution and each bar represents the duration of each executable in relation to all the other executables; longer bars being a good indication of where problems might lie. The colour of the bar indicates whether it was successful or not (green=success). Hovering over a bar brings up a tooltip showing more information about that executable. Clicking on a bar allows you to compare this particular instance of the executable against other executions. Please do let me know if you are using SSIS Reporting Pack. I would like to hear any anecdotes you might have, good or bad. @Jamiet

    Read the article

  • Can connect to DNS addresses typed in the URL but not by IP addresses

    - by Ben
    I just changed over my modem to bridged mode, and changed my wireless router to PPPoE. My PC IP address is reserved and forwards port 80 to my computer's IP address based on my MAC address. I have a problem, however. I cannot access my local webserver by public IP address or my router 192.168.0.1 wirelessly from any other computer or iPad. I can, however, connect by this PC which is connected to the wireless router via ethernet. Via wireless, it says it cannot connect, however DNS addresses work (e.g. google.com, etc.) Any ideas?

    Read the article

  • How can I place a ProgressBar in Android using Cocos 2d?

    - by Laxmipriya
    I want to place a horizontal progress bar in my Android application and I want to change its progress color. I used the following code, but the progress bar is not being displayed. CCProgressTimer progressBar = CCProgressTimer.progress("progressbar.png"); progressBar.setType(kCCProgressTimerTypeHorizontalBarLR); progressBar.setScale(5); progressBar.setAnchorPoint(CGPoint.ccp(0, 0)); progressBar.setPosition(CGPoint.ccp(0,0)); addChild(progressBar);

    Read the article

  • OpenVPN, Server 12.04, connect to machines in home LAN behind VPN server

    - by inexion
    Problem: I've set up a working OpenVPN server, and am able to connect to it from anywhere using my mac laptop and tunnelblick. When I connect in, I'm assigned an IP address of 10.8.0.x, the server is 10.8.0.1, so I have no problems SSHing into it. Once SSHd in, I can even ping other machines (obviously) on my home network (192.168.1.x). Desired outcome: What I want, is, to connect to the VPN server, and instead of getting a 10.8.0.x address, I get a 192.168.1.x on my home network. I can't figure out how to talk to the OTHER machines on my home network WITHOUT being SSHd in to the VPN server. I'd like to just connect to my VPN server, then be a part of my home network. Attempted solutions: I've read that I need to set up routes, and/or enable IP forwarding. I enabled IP forwarding using sudo sysctl -w net.ipv4.ip_forward=1 and that doesn't seem to have done anything. I've also uncommented a line in the OpenVPN's server.conf file: # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. push "route 192.168.1.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" But still no luck, I still get a 10.8.0.x address... I've also read I may have to add routes to the router itself, but haven't tried that. Any help appreciated, thanks!

    Read the article

  • Windows 7 Multi-NIC woes

    - by Eric
    I have Comcast business Internet here. It gives me 5 static IPs. Most of the machines in my house connect to a router like every other household. It has a 192.168.117.x subnet, DHCP Server, etc. and all is well. However, I have a second machine on MY desk that has a life Internet IP. Up until yesterday, this machine was running XP Pro. The primary NIC was manually set to 192.168.117.241 with no gateway, and the secondary NIC was manually set to 173.x.x.171 with a gateway of 173.x.x.174. This worked just fine for years. Yesterday I replaced that XP machine with a brand new Windows 7 x64 box. Again, I configured it the same way. The onboard NIC was given a static 192.168.117.x address with no gateway, and the secondary NIC was given a live Internet IP address with the proper router, etc. 2 Problems. First is that the internal network (192.168.117.x) is listed as a public network because there's no gateway, so that means no homegroup, no file sharing, none of that. And I can't change it from what I'm reading... The second is that the machine reports the "router" ip address as it's address, and not the address that it's supposed to. I'm ready to tear my hair out over this. Any ideas?

    Read the article

  • pound: multiple domains

    - by niklassaers
    Hi guys, I've been using pound to run mydomain.dk. Now I've bought some other domains and SSL certificates that are mydomain.no, mydomain.se and mydomain.eu. My old config looked roughly like this: ListenHTTPS Address 81.19.246.120 Port 443 Cert "/usr/local/etc/pound.keys/mydomain.dk.pem" Service BackEnd Address 10.0.10.10 Port 8080 End End End At places like here I've seen that I can use HeadRequire in the Service part, but I want the Host header to go together with the Cert, ideally something like ListenHTTPS Address 81.19.246.120 Port 443 HostAndCert "mydomain.dk" "/usr/local/etc/pound.keys/mydomain.dk.pem" HostAndCert "mydomain.se" "/usr/local/etc/pound.keys/mydomain.se.pem" HostAndCert "mydomain.no" "/usr/local/etc/pound.keys/mydomain.no.pem" HostAndCert "mydomain.eu" "/usr/local/etc/pound.keys/mydomain.eu.pem" Service BackEnd Address 10.0.10.10 Port 8080 End End End Any suggestions or clues to how I can accomplish this? Cheers Nik

    Read the article

  • Hosting multiple email domains on single server

    - by sharjeel
    Is it practically possible to host multiple email domains on a single machine with single IP address? Considering that spam filters do RDNS and in that case one IP address may host only one domain to pass the spam filters. If not, how does the hosted email work? Do they have get a separate IP address for each domain's email they host?

    Read the article

  • Using commands with ApplicationBarMenuItem and ApplicationBarButton in Windows Phone 7

    - by Laurent Bugnion
    Unfortunately, in the current version of the Windows Phone 7 Silverlight framework, it is not possible to attach any command on the ApplicationBarMenuItem and ApplicationBarButton controls. These two controls appear in the Application Bar, for example with the following markup: <phoneNavigation:PhoneApplicationPage.ApplicationBar> <shell:ApplicationBar x:Name="MainPageApplicationBar"> <shell:ApplicationBar.MenuItems> <shell:ApplicationBarMenuItem Text="Add City" /> <shell:ApplicationBarMenuItem Text="Add Country" /> </shell:ApplicationBar.MenuItems> <shell:ApplicationBar.Buttons> <shell:ApplicationBarIconButton IconUri="/Resources/appbar.feature.video.rest.png" /> <shell:ApplicationBarIconButton IconUri="/Resources/appbar.feature.settings.rest.png" /> <shell:ApplicationBarIconButton IconUri="/Resources/appbar.refresh.rest.png" /> </shell:ApplicationBar.Buttons> </shell:ApplicationBar> </phoneNavigation:PhoneApplicationPage.ApplicationBar> This code will create the following UI: Application bar, collapsed Application bar, expanded ApplicationBarItems are not, however, controls. A quick look in MSDN shows the following hierarchy for ApplicationBarMenuItem, for example: Unfortunately, this prevents all the mechanisms that are normally used to attach a Command (for example a RelayCommand) to a control. For example, the attached behavior present in the class ButtonBaseExtension (from the Silverlight 3 version of the MVVM Light toolkit) can only be attached to a DependencyObject. Similarly, Blend behaviors (such as EventToCommand from the toolkit’s Extras library) needs a FrameworkElement to work. Using code behind The alternative is to use code behind. As I said in my MIX10 talk, the MVVM police will not take your family away if you use code behind (this quote was actually suggested to me by Glenn Block); the code behind is there for a reason. In our case, invoking a command in the ViewModel requires the following code: In MainPage.xaml: <shell:ApplicationBarMenuItem Text="My Menu 1" Click="ApplicationBarMenuItemClick"/> In MainPage.xaml.cs private void ApplicationBarMenuItemClick( object sender, System.EventArgs e) { var vm = DataContext as MainViewModel; if (vm != null) { vm.MyCommand.Execute(null); } } Conclusion Resorting to code behind to bridge the gap between the View and the ViewModel is less elegant than using attached behaviors, either through an attached property or through a Blend behavior. It does, however, work fine. I don’t have any information if future changes in the Windows Phone 7 Application Bar API will make this easier. In the mean time, I would recommend using code behind instead.   Laurent Bugnion (GalaSoft) Subscribe | Twitter | Facebook | Flickr | LinkedIn

    Read the article

  • Debian/OVH: How to configure multiple Failover IP on the same Xen (Debian) Virtual Machine?

    - by D.S.
    I have a problem on a Xen virtual machine (running latest Debian), when I try to configure a second failover IP address. OVH reports that my IP is misconfigured and they complaint they receive a massive quantity of ARP packets from this IPs, so they are going to block my IP unless I fix this issue. I suspect there's a routing issue, but I don't know (and can't find any useful info on the provider's website, and their support doesn't provide me a valid solution, just bounce me to their online - useless - guides). My /etc/network/interfaces look like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address AAA.AAA.AAA.AAA netmask 255.255.255.255 broadcast AAA.AAA.AAA.AAA post-up route add 000.000.000.254 dev eth0 post-up route add default default gw 000.000.000.254 dev eth0 # Secondary NIC auto eth0:0 iface eth0:0 inet static address BBB.BBB.BBB.BBB netmask 255.255.255.255 broadcast BBB.BBB.BBB.BBB And the routing table is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 000.000.000.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 0.0.0.0 000.000.000.254 0.0.0.0 UG 0 0 0 eth0 In these examples (true IP addresses are replaced by fake ones, guess why :)), 000.000.000.000 is my main server's IP address (dom0), 000.000.000.254 is the default gateway OVH recommends, AAA.AAA.AAA.AAA is the first IP Failover and BBB.BBB.BBB.BBB is the second one. I need both AAA.AAA.AAA.AAA and BBB.BBB.BBB.BBB to be publicly reachable from Internet and point to my domU, and to be able to access Internet from inside the virtual machine (domU). I am using eth0 and eth0:0 because due to OVH support, I have to assign both IPs to the same MAC address and then create a virtual eth0:0 interface for the second IP. Any suggestion? What am I doing wrong? How can I stop OVH complaining about ARP flood? Many thanks in advance, DS

    Read the article

  • exim4 redirect mail sent to *@domain1.example.com to *@domain2.example.com

    - by nightcoder
    Current situation: We have a VPS that hosts a website example.org. Exim is configured to work as a smarthost. All emails sent through exim are successfully relayed to another mail server (that is working on example.com). Goal: To forward mail sent to *@example.org to *@example.com, i.e. change the recipient's address from *@example.org to *@example.com. Problem: If I send email to address *@example.org, then it seems exim doesn't change the address, it still relays the message to another mail server but recipient is still *@example.org. Maybe the redirect is not applied for some reason. Configuration and logs: /etc/exim4/update-exim4.conf.conf: dc_eximconfig_configtype='smarthost' dc_other_hostnames='' dc_local_interfaces='' dc_readhost='example.org' dc_relay_domains='example.org' dc_minimaldns='false' dc_relay_nets='0.0.0.0/32' dc_smarthost='example.com::26' CFILEMODE='644' dc_use_split_config='false' dc_hide_mailname='true' dc_mailname_in_oh='true' dc_localdelivery='maildir_home' /etc/exim4/conf.d/router/999_exim4-config_redirect (created by me): domain_redirect: debug_print = "R: forward for $local_part@$domain" driver = redirect domains = example.org data = [email protected] (for now data is set to a specific address for simplicity and testing) exim log when sending email to [email protected] (should be redirected to [email protected]): 2012-03-20 19:40:07 1SA4ud-0005Dw-7k <= [email protected] U=www-data P=local S=657 2012-03-20 19:40:08 1SA4ud-0005Dw-7k => [email protected] R=smarthost T=remote_smtp_smarthost H=domain2.com [184.172.146.66] X=TLS1.0:RSA_AES_256_CBC_SHA1:32 DN="C=US,2.5.4.17=#13053737303932,ST=TX,L=Houston,STREET=Suite 400,STREET=11251 Northwest Freeway,O=HostGator.com,OU=HostGator.com,OU=Comodo PremiumSSL Wildcard,CN=*.hostgator.com" 2012-03-20 19:40:08 1SA4ud-0005Dw-7k Completed So, the address is not changed :( Please help! I'm trying to make it work for half a day already :(

    Read the article

< Previous Page | 160 161 162 163 164 165 166 167 168 169 170 171  | Next Page >