Search Results

Search found 15651 results on 627 pages for 'setup'.

Page 165/627 | < Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >

• Regarding partitions for dual-booting Ubuntu with pre-existing Windows 7

  - by Shasteriskt

  I have zero actual experience with configuring disk partitions and the stuff I have read for the past few hours have been confusing me a bit, so please bear with me. First of all, I'd like to explain what I'm setting to achieve: Windows 7 with: C:\ Windows 7 (pre-existing installation) D:\ Data (Already exists and has files already) Ubuntu 11 - Does not exist yet, but I already have a LiveCD in hand. \root directory for Ubuntu \home on its own partition I plan \swap on its own partition with around 8GB Here is the current situation: I have a single 500 GB hard-disk with Windows 7 x64 installed, and the current partition schemes is as follows: System Reserved: 100 MB (Primary, Active) C: 100 GB - Where Windows 7 is installed (Primary) D: 365 GB - Where my files are located, LOTS of free space (Primary) Now, I would like to shrink my D: drive and create around 40 GB of unallocated disk space for the Ubuntu installation, but here what's confusing me a bit: I'm thinking I would create an extended partition and subdivide it into 3 logical partitions for the Ubuntu setup I had in mind. (If you think my setup is a bad idea, please let me know & why. I also hope you can suggest a better one...) I am aware that I can only have up to 4 primary partitions, or 3 primary partitions with 1 extended parition max. Now, does the System Recovery portion count as one primary partition? I'm really new to these things and it is totally unclear to me. In shrinking my D: drive using Windows 7's Disk Management tool, I would get an unallocated free space which I don't know how to make an extended partition from. It seems like I can only create a primary partition from it, not an extended one. How do I go about it? (I'd also like to note, if it is of any importance, that I am trying to avoid using the option to install Ubuntu alongside Windows, and much rather prefer using the custom install where I can specify which drives I wish to use and stuff. Somehow I feel its safer that way.)

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• DVI splitter not working as expected/confusion between DVI-D and -I

  - by Freakishly

  Hey guys, thanks for looking. I have an ATI FirePro™ V3700 in my desktop machine, and I have been running a dual-monitor setup quite effortlessly, thanks to the two DVI ports on the card. I came upon a third monitor, and wanted to extend my desktop to 3 screens, so I purchased a DVI splitter from Amazon. Now, I can only duplicate the second monitor onto the third, not extend it. I've tried all possible combinations of input to no avail. Here's the setup: The ATI FirePro™ V3700 has two Dual-Link DVI-I outputs The splitter splits a single Dual-Link DVI-I port into two Dual-Link DVI-I outputs Two of the monitors are NEC E222W, and the third monitor is a Dell 2001FP. Each monitor has one D-Sub and one Dual-Link DVI-D input. Cables going from the video card to the monitors are two Dual-Link DVI-D to the NECs and one Single-Link DVI-D to the Dell. Is the problem likely with the DVI-D/DVI-I mismatch? Or is it with the cable on the Dell that is only a Single-Link? The cables are easily replaceable, the monitors not so much. Thanks for your time, I really appreciate it. http://www.amd.com/us/products/workstation/graphics/ati-firepro-3d/v3700/Pages/v3700-specs.aspx http://www.amazon.com/Cables-Unlimited-DVI-D-Splitter-PCM-2260/product-reviews/B000H09RFM/ref=dp_top_cm_cr_acr_txt?ie=UTF8&showViewpoints=1 www dot newegg dot com/Product/Product.aspx?Item=N82E16824002495 accessories dot us dot dell dot com/sna/PopupProductDetail.aspx?cs=19&l=en&c=us&sku=320-1578 Apologies for the fudged links, I'm new here and they won't let me post more than two :P

  Read the article

• Why is windows not able to create a system partition?

  - by hughes

  I'm reinstalling Windows 7 64 bit, and I encountered an issue I've never seen before. I have a legit copy of Win 64 Professional, and I've installed it probably a half dozen times on this machine in the past without a problem. Googling the error only brings me to issues with people who are upgrading to win7. The drive itself seems to not have a problem. I can mount it on other systems and I can create an NTFS partition on it on other machines. I can install Ubuntu on it without any issues. Additionally, if I try using my alternate backup hard drive, the installer gives the same error. I have run diskpart from the setup page and clean seems to report that all is well. However, I cannot get past the screen below, which says Setup was unable to create a new system partition or locate an existing system partition. This happens regardless of whether or not the disk space is already allocated. What is causing this? How do I solve or get past this?

  Read the article

• How can I install .NET framework 3.5 on XP machines without internet connection?

  - by EricSchaefer

  I want to install .NET framework 3.5 on a couple of machines that do not have internet access. If I install the "no internet access"-package it still wants to download something. How can I figure out what is missing? Are there other installation packages? Edit: I would present screenshots but I cannot upload anything from here and the shots would be in german. So I present only the text translated back to english... Installing the "full redistributable package": At the bottom of the license agreement page it display this text: Size of download file: 67 MB Appoximate download time: 2h 44min (56KBit/s) 18min (512KBit/s) It shows the text even if I installed Windows Installer 3.1. After agreeing it displays the "Download and Installation Status"-Dialog with a progress bar labeled "Download:" and Status: Connection to server attempted (try X of 5). Total Download Status: 56MB/67MB I tried it in a VM with no network connection. It tries 5 times while the progress bar shows progress. Later the progress bar is labeled "Installation:". Even later it reports problems during setup and provides two buttons "Send Report Later" and "Don't Send". Now here it comes: "Setup completed" and "Microsoft .NET Framework 3.5 has been deinstalled successfully." (Emphasis is mine) "It is recommended to install current service packs and security updates. More information at Windows Update (link)." Edit2: Installed Service Pack 3, but still no success.

  Read the article

• VPN into multiple LAN Subnets

  - by Rain

  I need to figure out a way to allow access to two LAN subnets on a SonicWall NSA 220 through the built-in SonicWall GlobalVPN server. I've Googled and tried everything I can think of, but nothing has worked. The SonicWall NSA management web interface is also very unorganized; I'm probably missing something simple/obvious. There are two networks, called Network A and Network B for simplicity, with two different subnets. A SonicWall NSA 220 is the router/firewall/DHCP Server for Network A, which is plugged into the X2 port. Some other router is the router/firewall/DHCP server for Network B. Both of these networks need to be managed through a VPN connection. I setup the X3 interface on the SonicWall to have a static IP in the Network B subnet and plugged it in. Network A and Network B should not be able to access each other, which appears the be the default configuration. I then configured and enabled VPN. The SonicWall currently has the X1 interface setup with a subnet of 192.168.1.0/24 with a DHCP Server enabled, although it is not plugged in. When I VPN into the SonicWall, I get an IP address supplied by the DHCP Server on the X1 interface and I can access Network A remotely although I do not have access to Network B. How can I allow access to both Network A and Network B to VPN clients although keep devices on Network B from accessing Network A and vice-versa. Is there some way to create a VPN-only subnet (something like 10.100.0.0/24) on the SonicWall that can access Network A and Network B without changing the current network configuration or allowing devices on both netorks "see" each other? How would I go about setting this up? Diagram of the network: (Hopefully this kind of helps) WAN1 WAN2 | | [ SonicWall NSA 220 ]-(X3)-----------------[ Router 2 ] | | (X2) 192.168.2.0/24 10.1.1.0/24 Any help would be greatly appriciated!

  Read the article

• Wifi Works with Android and Windows 8 but not Linux and Win 7

  - by eramm

  Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

  Read the article

• Display stretches 4:3 ratios; Adds scrolling to other ratios

  - by Matt

  I have a dual monitor setup. Normally, they both display at 1680x1050. They have been setup this way for about a year. I'm using Windows XP Professional 2003 x64 SP2. Today, out of nowhere, one of the monitors kicked back to a lower resolution. I was not playing with any configuration at the time.. in fact all I had done was close a window (maybe a browser). But the thing is that the resolution is still preserved partially by the fact that the screen will scroll when you move the mouse. So it's like looking through a 1024x768 window into a 1680x1050 world. The monitor itself does not appear to be damaged, because I also have it connected to my netbook (via KVM) and higher resolutions work fine. I tried uninstalling/reinstalling the drivers to no avail. System restore doesn't help either. I'm unsure of the exact ATI card I'm using.. Device Manager lists it as "Radeon X300/X550/X1050". There is no Catalyst Control Center software installed. I tried to install it, but there doesn't seem to be a way to install it by itself ... it forces you to install another driver, which breaks both of my displays, forcing me to go into safe mode and run system restore again. Any ideas? Thanks EDIT: After playing around more, I discovered that the "scrolling" behavior is only present for aspect ratios that are not 4:3. For 4:3 ratios, it just stretches out to fit the wide screen. My monitor's native ratio is 16:9 .. what could be causing it to think it needs to scroll?

  Read the article

• Network topology for both direct and routed traffic between two nodes

  - by IndigoFire

  Despite it's small size, this is the most difficult network design problem I've faced. There are three nodes in this network: PC running Windows XP with an internal WiFi adapter.Base station with both WiFi and a Wireless Modem (WiModem)Mobile device with both WiFi and WiModem The modem is a low-bandwidth but high-reliability connection. We'd like to use WiFi for high-bandwidth stuff like file transfers when the mobile is nearby, and the modem for control information. Here's the tricky part: we'd like the wifi traffic to go directly from the mobile to the PC, as rebroadcasting packets on the same WiFi channel takes up double the bandwidth. We can do that with a manual configuration by giving the both the PC and the base station two IP addresses for their WiFi interfaces: one on a subnet shared with the mobile, and one on their own subnet. The routes on the PC are set up so that any traffic going to the mobile via WiModem goes through the secondary IP address so that return traffic from the mobile also goes through the WiModem. Here's what that looks like: PC WiFi 1: 192.168.2.10/24 WiFi 2: 192.168.3.10/24 Default route: 192.168.2.1 Base Station WiFi 1: 192.168.2.1/24 WiFi 2: 192.168.3.1/24 WiModem: 192.168.4.1/24 Mobile WiFi: 192.168.3.20/24 WiModem: 192.168.4.20/24 We'd like to move to having the base station automatically configure the mobile and PC, as the manual setup is problematic when you start having multiple mobiles and PCs. This means that the PC can only have 1 IP address and needs to be treated as being pretty simple. Is it possible to have a setup driven by DHCP on the base station that is efficient with bandwidth?

  Read the article

• GIT Website Deployment

  - by Brian

  I am attempting to setup GIT to deploy my project to different locations based on the branch. (I think this is what I want to do anyway). My current setup is this: Local dev machine running Netbeans to make changes. Remote server hosting GIT projects (same server running apache) - 2 subsites exist a test.FQDN.com and a live.FQDN.com What I would like to do is have 1 GIT project (MyProject) and create a new feature branch. Any commits done to the new feature branch would push to test.FQDN.com. Once the features have been tested and then merged into the master branch, it would push to live.FQDN.com. I have looked at GIT's post-receive hooks and was able to use "git checkout -f" command to pull on the test.FQDN.com site however that only pulls the master branch and not the new feature branch. I do not have any funding to use a third party to make this work, and would prefer to stay within GIT but have full root access to the web server if there is a package to install which would help control this. Any suggestions would be great!

  Read the article

• Dell Vostro Desktop error.

  - by goldenmean

  Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

  Read the article

• Accessing a webpage folder with .htaccess in it via apache webdav?

  - by pingo

  I have setup webdav access in order to enable an external user to upload the content of his web page to his folder on my server that is served by apache to the web. This way he could update his web page via webdav. Now the problem is that the user requires a .htaccess file and of course .htaccess breaks webdav probably because it overrides settings. (new files cannot be uploaded anymore via webdav if below specified .htaccess exists) I am running Apache2.2.17 and this is my webdav config: Alias /folderDAV "d:/wamp/www/somewebsite/" <Location /folderDAV> Order Allow,Deny Allow from all Dav On AuthType Digest AuthName DAV-upload AuthUserFile "D:/wamp/passtore/user.passwd" AuthDigestProvider file require valid-user </Location> This config is part of my naive solution to fixing this problem. The idea was to specify an alias to the web page folder where webdav would be enabled and then set AllowOverride to none so that the .htaccess would have no effect. Of course I then found out that in <Location /> AllowOverride directive is not valid. The .htaccess file looks like this: #opencart settings Options +FollowSymlinks Options -Indexes <FilesMatch "\.(tpl|ini)"> Order deny,allow Deny from all </FilesMatch> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)\?*$ index.php?_route_=$1 [L,QSA] ErrorDocument 403 /403.html deny from 1.1.1.1/19 allow from 2.2.2.2 What would be the solution here? I would like to have the web page accessible from the web but at the same time be able to access and modify it via apache's webdav (with digest auth). How would I do that? Also if possible I would like a solution that permits the existence of the .htaccess so that the user still has the power to setup access rules for his web page.

  Read the article

• How to verify TRIM/discard on encrypted swap?

  - by svarni

  I am using an encrypted swap partition via ecryptfs-setup-swap on my Ubuntu 13.04 computer using a SSD. I have manually set up trim for my ext4 root partition (simply by adding the "discard" option in /etc/fstab). I also manually ran fstrim on the root partition prior to booting and using dstat I saw that for a few seconds several GB/s of data have been written to the disk. That was presumably the effect of the trim command. These high writerates are reproducable by deleting huge files and have not occured before setting up trim, so I take them as evidence for working trim/discard. Manually enabling trim on my root partition has stopped the wearout of my precious new disk from 365 used reserved blocks (out of 6176 total) within three months down to 0 additional used reserved blocks within three additional months (data from SMART attributes). Because I want to minimize the wearout of my SSD I now would like to know whether my swap partition (which is encrypted using ecryptfs-setup-swap) also makes use of the trim/discard option. I tried sudo swapon -d -v /dev/mapper/cryptswap1 but did not receive particular information ("-v") about whether trim/discard ("-d") was applied. If unsupported, i would expect a message. Then I tried sudo dd if=/dev/sda6 count=1 BS=1M | xxd | less directly after booting and when no swapspace was used but I saw not only zeroes. I assume, when looking at freshly trimmed regions, the disk would send zeroes instead of reading random sectors (and according to some forums, (unencrypted) swap space is trimmed once upon boot). Long story short: Are there any ideas on how to test if trim is effectively used for my encrypted swap? And if not, any ideas on how to - at least manually, for once - trim the whole swap space? I wouldn't want to tinker with the partition itself, because I dont know if it needs to be reinitialized as (encrypted) swap - I dont want to be left with an unbootable system :)

  Read the article

• Monitoring instantaneous network throughput at one second intervals?

  - by Shaddi

  For a testing setup I have, I need to monitor the throughput through a "router"* at regular intervals of around 5 seconds or less (sub-second intervals would be very nice, but not required). Ideally, I would be able to generate a file which contained both the number of bytes and packets seen during each interval. I will eventually be generating a time-series of throughput from this data. On a previous setup using an older version of FreeBSD, there was a tool called "bpfmon" which gave me this information. However, I need to do this under a modern version of Linux (namely, Ubuntu 11.04). I have looked at both iptraf and iftop, but these do not appear to provide the resolution I need, nor do they seem to easily allow scraping the data I need. I understand iptables statistics may be able to give me what I'm after, but the examples I've seen of this seem to rely on repeatedly reading and resetting traffic counters, which seems like it could give inaccurate as read/reset is not an atomic operation. I already capture a tcpdump trace of the traffic I'm interested in on the link I want to monitor, so I am open to approaches which simply parse that. I feel like this must be a common problem though, so I am hoping there will be a standard "best practice" tool for accomplishing this. *I say "router" in quotes because I am really talking about a machine with two bridged NICs through which all the traffic I'm interested in passes.

  Read the article

• Inbox not updating in Exchange 2010, all users affected

  - by TuxMeister

  I'm battling against this darn issue this morning. We have the following setup: Big Hyper-V machine hosting the servers as VM's VM for CAS: WEB.XXX.local VM for Mailbox: EXC.XXX.local Servers are running Server 2008 R2 with Exchange 2010 SP1 Clients are all running Windows 7 Pro x64 with Outlook 2010 x64 The problem we're having is that nobody is able to see any emails received today (16th of October), but they are able to send externally. When I reply back to the email received externally, I don't get an NDR, yet the user cannot see my email. This is what I found and tried thus far: If we create a subfolder in Outlook 2010 and move any email from the inbox into that folder, changes will be immediately reflected in OWA We've been sending test emails to other users internaly and external email addresses and the sent items folder contains all those tests, synced properly to OWA as well Have tried crating a new profile, new emails are still missing Tried disabling Cache Mode, still no luck Also disabled "Download shared folders", still no luck Tried to setup a brand new Exchange mailbox and configured it on a VM that never had Outlook on it, still the same issue Tried restarting Exchange services on both CAS and Mailbox servers, no luck Tried rebooting both CAS and Mailbox servers, still no luck Performed a Mailbox Discovery on my admin account, emails from today are being found in the Discovery results, so the stuff is there, just not updating the user inboxes Any idea about what this hellish thing can be? I've done everything I can think of and also everything I could find out there. Let me know if you need any more details and thanks for reading this!

  Read the article

• pcfg_openfile: unable to check htaccess file, ensure it is readable

  - by rxt

  After moving a website folder on my local development machine to another drive, then moving it back, I got a 403 error. Most of this problem had probably to do with rights that got messed up. After deleting the code and restoring it from SVN, the rights seemed allright. The error stayed however. The setup is a bit complex, as follows: I have Ubuntu 10.4 as development machine, trying to mimic the server as much as possible We use Eclipse + SVN and I create all projects in a local folder under my user account In /var/www-vhosts I create folders for each vhost, like this one: test.localhost test.local/index.php: includes the index file of the project test.local/.htaccess is a dynamic link to the htaccess file in a project subfolder I get the following error in the apache error log: [Thu Jul 08 15:55:56 2010] [crit] [client 127.0.0.1] (13)Permission denied: /var/www-vhosts/test.localhost/.htaccess pcfg_openfile: unable to check htaccess file, ensure it is readable The problem seems to be the .htaccess file, or the link to it. When I empty the htaccess, nothing changes When I remove the link, the index-include produces some output (in the apache error log) When I remove the link and replace it with the actual file, I get another error: [Thu Jul 08 16:47:54 2010] [error] [client 127.0.0.1] Symbolic link not allowed or link target not accessible: /var/www-vhosts/test.localhost/test I'm lost here, don't know what to do next. Do you have any ideas what I can try? This setup has worked before, but I don't know what is different now.

  Read the article

• Creating a partitioned raid1 array for booting a debian squeeze system

  - by gucki

  I'd like to have the following raid1 (mirror) setup: /dev/md0 consists of /dev/sda and /dev/sdb I created this raid1 device using mdadm --create --verbose /dev/md0 --auto=yes --level=1 --raid-devices=2 /dev/sda /dev/sdb This gave a warning about metadata being 1.2 and my system might not boot. I cannot use 0.9 because it restricts the size of the raid to 2TB and I assume grub shipped with latest debian (squeeze) should be able to handle metadata 1.2. So then I created the needed partitions like this: # creating new label (partition table) parted -s /dev/md0 mklabel 'msdos' # creating partitions sfdisk -uM /dev/md0 << EOF 0,4096 ,1024,S ; EOF # making root filesystem mkfs -t ext4 -L boot -m 0 /dev/md0p1 # making swap filesystem mkswap /dev/md0p2 # making data filesystem mkfs -t ext4 -L data /dev/md0p3 Then I mounted the root partition, copied a minimal debian install inside and temporary mounted /dev /proc /sys. Afer this I chrooted to the new root folder and executed: grub-install --no-floppy --recheck /dev/md0 However this fails badly with: /usr/sbin/grub-probe: error: unknown filesystem. Auto-detection of a filesystem of /dev/md0p1 failed. Please report this together with the output of "/usr/sbin/grub-probe --device-map=/boot/grub/device.map --target=fs -v /boot/grub" to I don't think it's a bug in grub (so I didn't report it yet) but a fault of mine. So I really wonder how to properly setup my raid1, everything I tried so far failed.

  Read the article

• SFTP, SCP, Secure Webdav: which is the most suitable ?

  - by Xavier Maillard

  Hi, currently, I am hosting a webdav share setup in order to store files I need anywhere I am. It is available via HTTPS. Things are that I do not need all the HTTP machinery -i.e. my nginx http server is only there for this webdav folder. I am not sure I made the best choice. My requirements on the client side are: secured transfers mountable as a network drive at work with 'near realtime sync' usable for any OS I could use (including my mobile (android)) At first, I chose webdav since it would pass through my work proxy (which refuses all that is not on HTTP/S (port 80 or 443)). Today, I am not satisfied with the setup and even if nginx memory footprint is pretty small, its webdav support is not really "clean" and full. What would you recommend between SFTP, SCP and the current webdav solution ? I think SFTP is the closest solution but I still have to find out how to pass through my proxy ;) SCP seems quite limited as I read about it (only file transfers if I read right). Cheers

  Read the article

• Migrating WebLogic 10.3.0 to new host. Slow managed server startup times

  - by wadevondoom

  We are migrating our Blue Martini Commerce application (only supported on WebLogic 10.3.0) to a new host (Redhat 6.3 on a VMWare ESX vm). We are seeing extremely slow start up times for our managed server(s) that is basically 20x slower than our current production. As a for instance the Publish managed server takes ~30 - 45 seconds in current production and in the new environment it takes ~10 minutes. The setup uses the same domain structure and JVM as the current production environment. The same setup files are used. We use jdk1.6.0_33 on 64 bit architecture. We used the generic 64bit weblogic installer and used pack / unpack utilities to migrate the domain. The JAVA_OPTS to start this server are: "-d64 -Xms256m -Xmx512m -XX:PermSize=48m -XX:MaxPermSize=256m" The sysadmins have checked /etc/sysctl.conf and /etc/limits.conf to ensure we were not hitting some kind of process limit. As I am not sure what this managed server does from a Blue Martini perspective during the phase of startup I also had the DBA check to ensure that Oracle RAC (11.2.0.3) wasn't also hitting some kind of process limit or if there was a tns listener issue. The new host is quite a bit stricter with their server lock downs so there are a few differences.... Redhat 6.3 in new env, RH 5.7 in current SElinux is targeted in new env and disabled in current VM in new env and dedicated hardware in current iptables disabled in current. It was enabled in new prod but I had them disable it just in case I apologize for not being more specific. I am mostly hoping got some tips. I do not have the typical root access I would normally have in this environment. I am just hoping got a path forward. I did a few 'kill -3' to see if there are blocked threads and I got nadda. The service works for all intents and purposes it is just painfully slow. Thanks you all in advance for reading and best regards. Wade

  Read the article

• Can't see more than the first few lines in an SSH connection

  - by hello

  I need some help for SSH buffer size. I have a vista machine at home and i have installed "Free SSHD" on it. I also have Dynamic DNS setup to access some of my home lab equipment which are connected to this vista machine. From my work machine which is an XP machine I connect to my home machine using Putty. Everything up to this point is working fine without any problem. The issue is I can't see more lines than the first few lines of the output. I press the space bar to get more output off the screen and the output scrolls up and it gets lost as the more output gets displayed on the screen. The Putty client i am using on my work machine has been setup with enough buffer size but the output still only displays few lines and as it moves up, the buffer gets empty automatically. I have searched the entire web and haven’t found any proper solution any where. Can someone please help here? Thanks.

  Read the article

• Magical moving desktop icons

  - by Nathan Taylor

  I have encountered a very strange behavior in Windows 7 that I cannot seem to identify and I have never seen or heard of on any system configuration. Whenever I move my mouse to the left-most edge of my primary display (centered in 3-display setup), my desktop icons magically move away from the cursor (up or down and to the right). It only happens when my desktop has focus and the mouse is positioned on the left, top or bottom edge of the main display. Moving the mouse all the way to the right edge of my right secondary display causes the mouse icons to snap back into their correct position. Ridiculous video of the issue My setup is 3 displays on two display adapters. The main display is running at 2560x1600, connected to the machine via a USB-powered DVI-D to DisplayPort adapter and is driven by an NVIDIA NVS 3100M video card. The secondary displays are running at 1440x900 and 1200x1920 and are driven by integrated Intel HD Graphics (mobile). It seems like some kind of panning behavior, but it's obviously not working as expected. I have updated all of my drivers, but no change. It's probably worth noting that the desktop icons are set to auto-arrange.

  Read the article

• Can Dovecot IMAP automatically create Maildir folders for new (virtual) users?

  - by user233441

  everyone. I am learning to set up a dovecot home IMAP server using a virtual Ubuntu 12.04 machine. My intention is eventually to have a home server that uses POP3 to take email from several addresses and remove them from my ISP's servers, while making them accessible through a home IMAP server (this is similar to the setup described at https://help.ubuntu.com/community/POP3Aggregator, which explains how to set up the system with dovecot version 1, and is thus outdated). I intend to use the ISP's server directly when sending messages, and to BCC all sent messages to myself. I've completed the basic set up of the test server: getmail uses POP3 to fetch messages from two test email accounts, and successfully delivers them to the respective Maildir-style new folders on the virtual machine. Dovecot then successfully sees these messages. I have two questions: 1) I had to set up new, cur, and tmp folders for both of the test accounts manually to get this setup to work. Is there a way to get dovecot to create these Maildir folders automatically when I create a new virtual user account (e.g., when I add a user and password combination to my dovecot password file), or is it expected that I write a bash script to automate that task? 2) I would welcome any comments you have on how this approach could be improved as I learn to set it up. My motivations with this approach are 1) to enable archiving/storing emails from several hosting providers that impose a cap on server storage, and 2) to give me somewhat greater control over email storage without requiring that I set up and administrate a mail server from scratch (which I'm not yet prepared to do) (this follows the recommendations at https://ssd.eff.org/tech/email). Thank you!

  Read the article

• Cannot send email to info@ or support@

  - by user3022598

  I am trying to send email from my gmail account to a couple user accounts I have on my new Centos server. The email is setup correctly and I can send receive from accounts ok except info and support. I tried to setup two users "info" and "support" I have a php form that sends out email that works fine for all users except info and support. To test this and make sure that something did not change from yesterday i just created a new user "frank" and tried the submit form and it worked fine. From my gmail account i can email "frank" however i cannot email "info" or "support" The logs I pulled are as follows and i think i see the issue but no idea how to fix it. Aug 15 12:20:55 mail postfix/qmgr[1568]: 1815C20A83: from=, size=1815, nrcpt=1 (queue active) Aug 15 12:20:55 mail postfix/local[2270]: 1815C20A83: to=, relay=local, delay=0.28, delays=0.26/0.01/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Aug 15 12:17:13 mail postfix/qmgr[1568]: 3C18520A7F: from=, size=1818, nrcpt=1 (queue active) Aug 15 12:17:13 mail postfix/local[2201]: 3C18520A7F: to=, orig_to=, relay=local, delay=0.28, delays=0.25/0.01/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Aug 15 12:15:24 mail postfix/qmgr[1568]: 2F79420A79: from=, size=1813, nrcpt=1 (queue active) Aug 15 12:15:24 mail postfix/local[2155]: 2F79420A79: to=, orig_to=, relay=local, delay=0.29, delays=0.27/0.01/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) For some reason frank goes out fine, however support and info go to root? Why?

  Read the article

• How to connect the virtual networks of vmware guests running on different hosts?

  - by gyrolf

  In a test setup, we are running several virtual machines on a single vmware workstation host. All virtual machines are connected via a "host only" network. This runs fine up to 2 or 3 virtual machines (depending on the host hardware). To allow more virtual machines, we want to use more host machines. Details about the environment and applications: Host PCs are running Windows XP in a corporate intranet. VMware used is Workstation 6.5 Guests are running Windows Server 2003 All guests act as Web Servers One of the guests additionally acts as Windows File server, offering shared folders for the other guests to connect to. Restrictions: VMware guests shall not be visible from the intranet. Changes to the host PC are restricted by corporate policy. In the virtual network, no domain controller exists. All virtual machines are member of the same workgroup. Running the virtual network as NAT is possible. Port forwarding might be used if it does not conflict with ports used by the host PC. Looking for a solution, I found hints about using router or vpn software on the hosts, but without any details how to setup. (I found a similar question Sharing the network between 2 VMware hosts, but the answer was not sufficient for me.)

  Read the article

• Recovering ZFS pool with errors on import.

  - by Sqeaky

  I have a machine that had some trouble with some bad RAM. After I diagnosed it and removed the offending stick of RAM, The ZFS pool in the machine was trying to access drives by using incorrect device names. I simply exported the pool and re-imported it to correct this. However I am now getting this error. The pool Storage no longer automatically mounts sqeaky@sqeaky-media-server:/$ sudo zpool status no pools available A regular import says its corrupt sqeaky@sqeaky-media-server:/$ sudo zpool import pool: Storage id: 13247750448079582452 state: UNAVAIL status: The pool is formatted using an older on-disk version. action: The pool cannot be imported due to damaged devices or data. config: Storage UNAVAIL insufficient replicas raidz1 UNAVAIL corrupted data 805066522130738790 ONLINE sdd3 ONLINE sda3 ONLINE sdc ONLINE A specific import says the vdev configuration is invalid sqeaky@sqeaky-media-server:/$ sudo zpool import Storage cannot import 'Storage': invalid vdev configuration I should have 4 devices in my ZFS pool: /dev/sda3 /dev/sdd3 /dev/sdc /dev/sdb I have no clue what 805066522130738790 is but I plan on investigating further. I am also trying to figure out how to use zdb to get more information about what the pool thinks is going on. For reference This was setup this way, because at the time this machine/pool was setup it needed certain Linux features and booting from ZFS wasn't yet supported in Linux. The partitions sda1 and sdd1 are in a raid 1 for the operating system and sdd2 and sda2 are in a raid1 for the swap. Any clue on how to recover this ZFS pool?

  Read the article

< Previous Page | 161 162 163 164 165 166 167 168 169 170 171 172  | Next Page >