Search Results

Search found 7776 results on 312 pages for 'configure'.

Page 168/312 | < Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >

• nginx www.domain.com vs domain.com virtualhost

  - by m33lky

  I have an http block where I include virtual hosts for the different domains hosted on the same server. For each virtual host I do: listen domain.com:80; Now, domain2.com works fine. However, when I do www.domain2.com it shows the page for domain1.com! How to properly configure nginx? Does this have something to do whether www is a CNAME or an A record? Update: It looks like you can do the following: listen 80; server_name domain.com www.domain.com;

  Read the article

• Bacula Director and Storage in LAN

  - by B14D3

  I have two networks LAN and DMZ.. Machines in DMZ are accesible from internet ( only over http). In LAN I have servers that see all LAN and all DMZ machines but machinse from DMZ don't see any LAN servers. Machines in LAN have access only to all LAN and DMZ, no direct access to internet and no access from internet. DMZ <------ LAN DMZ ----X--->LAN I'm planning to configure Bacula as major backup system. My plan is to install Bacula Director and Storage deamon on the same server in LAN for safety reasons. So my question is: Will this configuration work, is it posible for bacula director and storage deamon installed on server in LAN to makes backup servers that are in my DMZ? Or in this network configuration Bacula should be in DMZ? (If yes will I can backup with it servers in LAN ?)

  Read the article

• SharePoint Web Analytics not tracking usage for main application

  - by Chris W

  My SP 2010 setup is two separate applications - one for the main portal and one for MySite. Whilst WebAnalytics is tracking usage of MySite it's not showing any stats for the main Portal. The only thing it lists is the number of site collections but no page views etc. The WA service is clearly running to pick up data for MySite. In Configure web analytics and health data collection everything is ticked. I can't find any obvious settings that are different between the two applications. Where should I look to get usage tracking correctly?

  Read the article

• Slow download speeds on MacBook Pro

  - by Austin

  Just as the title says, I am getting very low download speeds on my MacBook Pro. I did a speed test at speedtest.net, and am getting 7 MbPS down, .5 up. However, I can only seem to get 270 KB PS max (averaging 100 K), whether on my school's network or on my home network, wired or wireless. I am on Mac OS X 10.5.8, with Google Chrome. My ethernet settings (under System Preferences - Network - Ethernet Connection - Advanced - Ethernet) are set to "Configure Automatically", "Speed: 100TX", "Duplex: full-duplex, flow-control", and "MTU: Standard (1500)". As far as I can tell, there are no throttles or anything between here and the ISP, so... Any ideas on why I'm getting such low download speeds?

  Read the article

• Using old RAID configured disk after new disk has been used in the controller

  - by Narendra

  I have Dell Poweredge T100 server with Dell SAS 6 and two hard disk on RAID 1. Last week the server died including one RAID 1 hard disk. We sent the server for repair and the problem with PSU was fixed. But the repair guys also checked the RAID controller by configuring new RAID with their test hard disk. Now if I install one working RAID 1 disk and one new disk, will the RAID controller let me continue my old RAID 1 and resync the new disk and continue? What I fear is the RAID controller will want the test hard from repair guys. Thus I have to re configure RAID 1 forcing me to wipe the working disc. If so, I've to backup the working disc, reconfigure RAID 1 and reinstall? Or is there better way? Note: I'm using DELL SAS confiugratio utility to manage RAID. (Press CTRL+C after BIOS)

  Read the article

• Get active network interface on Windows

  - by Kevin Walzer

  I'm developing an application that provides a UI to windump, the packet sniffer. Windump has a "-D" parameter that lists all network interfaces it can find, and then you can specify which interface to listen on. However, I'd like to avoid forcing the user to manually configure which interface to listen on. On Unix, I can obtain the right network interface (en0, en1, etc.) via a call to ifconfig and some parsing of the output, but I cannot locate any equivalent Windows API or command that can yield similar information--ipconfig doesn't seem to obtain this data. Can anyone suggest either a Windows command-line tool or an API that can be called via VBScript to obtain this data so that I don't have to present the user with a dialog in my GUI telling them to select the right interface?

  Read the article

• Set up ad hoc wireless connection between Windows Vista and Mac OS X

  - by Skarab

  I have the following problem - Windows Vista does not connect to adhoc wireless network created on my Macbook. I have tried to create secured (with 40 bit key) and unsecured network but Windows Vista still has problems to connect. Windows VISTA informs me -- after 5 minutes of attempts - that setting up the connection -- with my adhoc network -- took too much time. My question: do I need to configure some settings on Vista to connect it to my Macbook? Maybe it is a problem with DHCP? Edited: I have tried the other way: http://superuser.com/questions/202890/set-up-an-adhoc-network-in-windows-vista-to-connect-to-and-share-the-internet-con

  Read the article

• Cannot Ping a server after configuring the Routing and Remote Access Services

  - by stacker

  After configuring the Routing and Remote Access Services to be a both VPN and NAT service, I cannot ping that server anymore from the external side. But when I configure it to be just a VPN server, or just a NAT server, I do able to ping it from the external side. My configuration is like: DC: 192.168.20.11 VPN and NUT: Nic 1: 192.168.20.1, NIC 2: 192.168.147.171 Client: 192.168.147.1 The mask is always: 255.255.255.0 I cannot understand why when configuring the VPN server to be a VPN and NAT, I cannot ping the server anymore.

  Read the article

• How to authenticate users in nested groups in Apache LDAP?

  - by mark

  I've working LDAP authentication with the following setup AuthName "whatever" AuthType Basic AuthBasicProvider ldap AuthLDAPUrl "ldap://server/OU=SBSUsers,OU=Users,OU=MyBusiness,DC=company,DC=local?sAMAccountName?sub?(objectClass=*)" Require ldap-group CN=MySpecificGroup,OU=Security Groups,OU=MyBusiness,DC=company,DC=local This works, however I've to put all users I want to authenticate into MySpecificGroup. But on LDAP server I've configured that MySpecificGroup also contains the group MyOtherGroup with another list of users. But those users in MyOtherGroup are not authenticated, I've to manually add them all to MySpecificGroup and basically can't use the nested grouping. I'm using Windows SBS 2003. Is there a way to configure Apache LDAP to do this? Or is there a problem with possible infinite recursion and thus not allowed?

  Read the article

• Using FastCGI for PHP on Mac OS X

  - by DanieL

  I have apache2 running on a Mac OS X (10.6) machine, and it is currently serving PHP pages fine, using php5_module but I would like to configure fastcgi_module to handle the php pages. I have tried using the configuration found on www.fastcgi.com but I get the following error: [warn] FastCGI: (dynamic) server "/Path/to/script.php" has failed to remain running for 30 seconds given 3 attempts, its restart interval has been backed off to 600 seconds [warn] FastCGI: server "/usr/bin/php" has failed to remain running for 30 seconds given 3 attempts, its restart interval has been backed off to 600 seconds I'm thinking this is because PHP has not been compiled with FastCGI, but seeing as it came with Mac OS X i'm not sure how to recompile it. Is this the problem? And if so, how do I recompile PHP with FastCGI?

  Read the article

• How to fill in the network line in the ubuntu interfaces config file?

  - by matnagel

  I have to configure an ubuntu hardy server network interface. The service hoster told me that this is the network data for the machine: IP Range: 111.111.200.74 to 111.111.200.78 Netmask: 255.255.255.248 Broadcast: 111.111.200.79 Gateway: 111.111.200.73 Subnet: 111.111.200.72/29 I am only using the first IP address. I will update the /etc/hosts file with 111.111.200.74, but I am still unsure how the /etc/network/interfaces file should be. This is my plan: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 111.111.200.74 netmask 255.255.255.248 network 111.111.200.??? broadcast 111.111.200.79 gateway 111.111.200.73 As you can see I don't know how to build the network line. How would I calculate the data for the network line and what is the result? (I changed the first 2 octets of the subnet, they are not "111.111" in the real setup.)

  Read the article

• Wordpress blog website apache and IIS subdirectory

  - by Philippe

  The issue is this : Our company has a website hosted on an IIS server. I have recently been given the task to configure a WordPress server for an eventual WordPress blog so that our social media employee could test and see how it works. This was completed successfully and easily on a new server and on a WAMP configuration. The website was published as wordpress.domain.com and works fine. HOWEVER! I have now been requested to ensure that the soon-to-go-online blog would be accessible through the address domain.com/blog. Is there a way to modify the original company website and simple redirect the /blog to the Apache WordPress website? If not, is there a way to transfer the wordpress.domain.com on the IIS server hosting the main website and keep the configuration? Is there a better solution that I haven't thought about (probably)? If so, what would you all suggest?

  Read the article

• How to display a graph only for business hours with CACTI?

  - by Blast Raider

  I have noticed that I can only display an uninterrupted period with Cacti. I am wondering whether is possible or not to make a custom graph which displaying only the business hours during a period (a week, a month, etc.). If it is possible, how could I configure it on Cacti ? For example, I would like to be able to display a graph with an average inbound/outbound traffic between 8am and 7pm for 5 business days a week of the last month. I would apreciate any help. Thank you.

  Read the article

• Perform action based on load avg

  - by sfx

  I'm running some web applications on an debian server and have to struggle with ddos attacks sometimes. It's eating up all my resources and I can't ssh anymore into the server. An idea was to drop all connections if the load avg is too high, so there are still resources for me and accept new connections if the load avg is low enough. Since this has to work under heavy load I'm afraid a cronjob wouldn't be fast enough or take too much resources. tl;dr: Is there a way to configure the behavior if the load avg is above a specific threshold?

  Read the article

• syslog ip ranges to specific files using `rsyslog`

  - by Mike Pennington

  I have many Cisco / JunOS routers and switches that send logs to my Debian server, which uses rsyslogd. How can I configure rsyslogd to send these router / switch logs to a specific file, based on their source IP address? I do not want to pollute general system logs with these entries. For instance: all routers in Chicago (source ip block: 172.17.25.0/24) to only log to /var/log/net/chicago. all routers in Dallas (source ip block 172.17.27.0/24) to only log to /var/log/net/dallas. Finally, these logs should be rotated daily for up to 30 days and compressed. NOTE: I am answering my own question

  Read the article

• How to automatically execute a shell script when logging into Ubuntu

  - by Mike Rowave

  How do I get a script to execute automatically when I log in? Not when the machine starts up, and not for all users, but only when I (or any specific user with the script) login via the GNOME UI. From reading elsewhere I thought it was .bash_profile in my home directory, but for me it has no effect. When I manually execute it in a terminal window by typing ~/.bash_profile it works, but it won't run automatically when I log in. I'm running Ubuntu 11.04. The file permission on my .bash_profile is -rwx------. No .bash_profile existed in my home directory before I created it today. I seem to remember older versions of Linux having a .profile file for each user, but that doesn't work either. How is it done? Do I need to configure something else to get the .bash_profile to work? Or does the per-user login script need to be in some other file?

  Read the article

• Remote Desktop fails after VPN connection.

  - by Samet Sorgut

  The remote computer is connected with Remote Desktop. When the remote computer is connected to VPN the Remote Destop freezes. It is not possible to connect to the remote computer again via Remote Desktop. What can be done to connect to this remote computer after it establishes a VPN connection? The only thing that comes to my mind is to install a second NIC and configure Remote Desktop to accept connection from this NIC while VPN is working from the other... What do you suggest?

  Read the article

• Web-based (intranet / non-hosted) timesheet / project tracking tools

  - by warren

  I realize some similar questions have been asked along these lines before, but from reading-through them today, it appears they don't match my use case. I am looking for a web-based, non-hosted time and project tracking tool. I've downloaded Collabtive and Achievo so far, but am looking for other suggestions, too. My list of requirements: runs on standard LAMP stack non-hosted (ie, there is an option to download and run it on a local server) not a desktop/single-user application easy-to-use - my audience is a mix of technical and non-technical folks easy to maintain - when time for upgrading comes, I'd really like to not have to rebuild the app (a la ./configure ; make ; make install) needs to support multiple users free-form project additions: we don't have a central project management authority (users should be able to add whatever they're working on, not merely from a drop-down) Does anyone here have experience with such tools? It doesn't have to be free.. but free is always nice :)

  Read the article

• How to stop ethernet interface in bridge configuration from obtaining IP address via DHCP

  - by user71061

  Hi! I'm trying to configure openvpn in bridging configuration. First step of doing this requires creating bridge interface (br0), bridging together physical ethernet interface (eth0) and logical tap0 interface. This can be done with simple script but I want to use less popular approach, configuring bridge interface entirely via /etc/network/interfaces file (on Debian linux). So I have removed all eth0 definitions form /etc/network/interfaces and replaced if with following br0 definition: auto br0 iface br0 inet static pre-up openvpn --mktun --dev tap0 address 10.0.0.1 netmask 255.255.255.0 bridge_ports eth0 tap0 post-down openvpn --rmtun --dev tap0 This works as I expected, but there is only one problem: interface eth0 is part of bridge interface br0 AND it also receive it's own IP address from my DHCP server (located on same LAN where eth0 is connected). My questions is: how to stop eth0 interface from obtaining it's own IP address? (It should only be part of br0 bridge).

  Read the article

• MAC to IP binding in ASA 5510 / SG 300-52

  - by Sampsa

  I am trying to configure a Cisco ASA 5510 to assign specific IP-addresses to specific MACs. Firmware on my ASA is 8.2(5). I have used this feature in our previous device (Cisco SA-520W). I have also read that this feature is (not yet) implemented. How do I work around this problem, if not by direct assignment? Do I need to specify fixed IP's on concerned devices themselves? I also have a SG 300-52 switch for our LAN. We cannot specify IP-addresses to ports, because we have further switches down the line. Thank you for your help!

  Read the article

• Using Virtual Domains with WordPress and Cherokee Web Server

  - by ikevinjp

  I'm trying to configure WordPress to work with Cherokee Web Server. The multi-site set up in WordPress is yyy.com and uses 'sub-domains'. Thus, I have sites like aaa.yyy.com, bbb.yyy.com - they all work fine so far. However, I have another completely different domain: abcde.com. Within WordPress, the sub-domain set up is abcde.yyy.com. When a public user accesses abcde.com, it cannot properly be redirected to the WordPress sub-domain abcde.yyy.com. How do I set up Cherokee to properly redirect virtual domains to WordPress? That means, the domain facing public would be abcde.com but WordPress would want to see abcde.yyy.com to properly return the correct content for the specific site. (I tried and it always get redirected to something like this: "http://yyy.com/wp-signup.php?new=abcde.com")

  Read the article

• *nix OS that is easy to update to latest software

  - by rjstelling

  I need to configure a server (*nix) that runs our (bespoke) CMS and Applications. In the past I have defaulted to using Cent OS 5, but I find this outdated difficult to upgrade the software to the versions we require. For example, we need PHP 5.3, but CentOS 5 has 5.2. Updating is fine but breaks something else (normally MySQL support in PHP). Eventually it will get to a situation where I can't upgrade because of missing dependancies and incompatible versions. Error: Missing Dependency: httpd = 2.2.3-43.el5.centos.3 is needed by package httpd-devel-2.2.3-43.el5.centos.3.i386 (updates) Is there a better alternative OS for hassle free updates, I need: Apache 2.2.17 (the development version for apxs) MySQL 5.5.8 PHP 5.3.5

  Read the article

• Is there a browser addon to redirect a link to another, modifying some address content automatically?

  - by kokbira

  Well, I'm looking for an addon that can redirect a link when I click on it in the following ways: Change from https to http Change from twitter.com/xxxxxxxxx to, for example, dabr.co.uk/xxxxxxxxx (added at 2010-02-15th, 20:30 GMT) Remove the "?utm_source=twitterfeed&utm_medium=twitter" from the end ou a URL Generally, replace a string with another (e.g. youtube->yt; so www.example.com/visitingyoutube would become www.example.com/visitingyt) PS: (added at 2010-02-15th, 20:30 GMT) @oKtosiTe, a clearer user case: Supposes that there is a link in Twitter that point to a URL X (URL X is http://www.newspapersite.com/2011-02-15_1304.html?utm_source=twitterfeed&utm_medium=twitter) In that case, I want to open that URL only until ".html", i.e., I want to open a URL Y, that is http://www.newspapersite.com/2011-02-15_1304.html What happens when I click normally in that link: 3.1. Browser goes to URL X What I want to happen when I click in that link: 4.1. The addon must transform URL X to URL Y (I must configure it before to change a piece of URL from "?utm_source=twitterfeed&utm_medium=twitter" to "" 4.2. The browser goes to URL Y

  Read the article

• How can i get SSO for alfresco on windows-7 to work?

  - by Maarten

  domain AD on windows 2008 R2, linux server alfresco 3.4c, windows-7 client. I'm trying to get automatically logged into alfresco from the windows-7 client. I've looked with wireshark to see what happens: 1. Client goes to /alfresco 2. Server sends Redirect to page 3. Client goes to Redirected page 4. Server sends a WWW-Authenticate: Negotiate header 5. Client DOES NOT respond to this how can i configure the windows-7 client (or the AD domain) so that the client will in fact engage with the SPNEGO protocol? instead of just asking for user credentials? (the user is logged in through kerberos in the domain.)

  Read the article

• php-fpm not working several days,return 'No input file specified'

  - by Magic

  My server running ubuntu 64bit, nginx, php-fpm. Everything is working well. But several days after. The browser display 'No input file specified'.After I restart php-fpm. Everything run well again.But this situation occur again and again.So I must restart the php-fpm several days.Anyone know what's the problem? nginx -V output sshadmin@ubuntu:~$ nginx -V nginx: nginx version: nginx/0.9.7 nginx: built by gcc 4.4.3 (Ubuntu 4.4.3-4ubuntu5) nginx: TLS SNI support enabled nginx: configure arguments: --user=www --group=www --prefix=/usr/local/nginx --with-http_stub_status_module --with-http_ssl_module --with-http_gzip_static_module

  Read the article

< Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >