Search Results

Search found 41598 results on 1664 pages for 'segmentation fault'.

Page 168/1664 | < Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >

• Restored Domain Controller does not display any information using dcdiag command

  - by dasko

  I am testing restoring a domain controller from system state backup to different hardware in a non production environment as a sanity check for our restoration procedure. When i run the dcdiag command I get "blank info back" and all that is displayed are two lines as follows: Domain Controller Diagnosis Performing initial setup: and then I am returned to the command prompt. Even when I do dcdiag /v i get the same result. I have double checked the DNS settings and Active Directory works properly. All FSMO roles are being held by this restored Domain Controller. I am able to join test pc's to the domain without issue etc Is this a common issue or is there something that I am missing. Thanks.

  Read the article

• One IP, One Port, Multiple Servers

  - by Adrian Godong

  I am looking for a solution to forward one public IP address and one specific port to different machines based on hostname (as of now, I need it only for HTTP). The current setup is NAT on a commodity router (it only provide simple public port to private IP address / port forwarding). I can add a Windows Server 2008 R2 machine before the router if required, but prefer not to do so. So ideally, I would like to have the current setup and the forwarding is done on one of the Windows Servers. Is it possible to do this?

  Read the article

• High load average, low CPU and IO (Centos 5.7)

  - by Ben

  A Drupal 7 site with CiviCRM, after running smoothly for a year on a 1&1 VPS suddenly became unresponsive. Now pages eventually load, but can take more than a minute. Looking at resource use in Virtuozzo, the load average carries a warning, and has remained above 1. While I understand this isn't particularly high, this is a change from when the site was working. Here is a typical snapshot of top: top - 03:10:32 up 3:21, 1 user, load average: 1.16, 1.22, 1.30 Tasks: 43 total, 1 running, 42 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 0.1%sy, 0.1%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2097152k total, 1015112k used, 1082040k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached CPU idle level never seems to go much below 70%. wa is virtually always at 0. There appears to be lots of free memory. And here is some vmstat output, again showign wa at 0, plenty of free memory, and an idle CPU: procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 0 0 1100872 0 0 0 0 2783 23672 0 538 1 0 99 0 0 1 0 0 1100872 0 0 0 0 0 16 0 101754 0 0 100 0 0 0 0 0 1100872 0 0 0 0 0 17 0 103133 0 0 100 0 0 0 0 0 1100872 0 0 0 0 0 1 0 102080 0 0 100 0 0 1 0 0 1100872 0 0 0 0 0 6 0 99881 0 0 100 0 0 0 0 0 1100872 0 0 0 0 0 1 0 105187 0 0 100 0 0 I've spoken to 1&1 but they don't have any ideas as to what could be causing the high load average. Instead they suggested an upgrade :) I've looked for processes that might be causing this, examined MySQL showprocesslist, and restarted the container with no result. Does anyone have more troubleshooting suggestions or insights?

  Read the article

• Using the Juniper EX3300 Switch as a router?

  - by Richard Whitman

  I have a Juniper EX3300 switch in a data center. And I have connected one of the uplink ports (ge-0/1/0) to my ISP's router. I want to configure it so that all the devices connected to ports in the same VLAN as ge-0/1/0 can access the Internet. I have done some research, and I haven't gotten anywhere really. I have configured the interface as follows: ge-0/1/0 { ether-options { no-auto-negotiation; link-mode full-duplex; speed { 1g; } } unit 0 { family inet { address xx.xx.xx.xx/32; } } } where xx.xx.xx.xx is the "Customer Router Port IP" assigned by my ISP. When I try to commit, I get the following error: Interface ge-0/1/0.0 not enabled for switching Can some one tell me what is the right way to configure it?

  Read the article

• Apache2 config problem

  - by Hellnar

  For using my Debian VPS for multiple domains , I did such actions: removed the default one from sites-enabled/ and sites-available/ (config and the symbolic link) and I added this under sites-available/www.mysite.com : <VirtualHost MYIP:80> ServerName mysite.com ServerAlias www.mysite.com Alias /media/ /home/myuser/mysite/media/ Alias /admin_media/ /home/myuser/django/Django-1.2/django/contrib/admin/media/ WSGIScriptAlias / /home/myuser/mysite/wsgi.py ErrorLog /home/myuser/mysite/logs/error.log CustomLog /home/myuser/mysite/logs/access.log combined </VirtualHost> And I have changed my ports.conf to: NameVirtualHost MYIP:80 Listen 80 <IfModule mod_ssl.c> # SSL name based virtual hosts are not yet supported, therefore no # NameVirtualHost statement here Listen 443 </IfModule> Lastly I enabled the new domain via the command: a2ensite www.mysite.com After restart I get this error: myuser:~# /etc/init.d/apache2 restart Restarting web server: apache2apache2: Syntax error on line 281 of /etc/apache2/apache2.conf: Syntax error on line 1 of /etc/apache2/sites-enabled/www.birertek.com: /etc/apache2/sites-enabled/www.birertek.com:1: <VirtualHost> was not closed. failed! Please help this poor soul.

  Read the article

• Windows Server 2008 DHCP with RRAS

  - by Guillermo Prandi

  I have a Windows Server 2008 R2 which is a member of a domain, but is placed in a remote location. The server is directly connected to Internet. Clients need to access a particular insecure TCP service in this server (ports 9730 and 9731). Since clients have dynamic IP addresses I cannot know in advance, I thought it would be nice to have them connected through a VPN in order to access the insecure service, but ONLY to access that service, like this: Client ------> VPN TUNNEL ------> (Insecure service at Server) | \----> (Normal internet access) I'd enable the insecure ports in the firewall only from VPN accesses. For this I configured RRAS in the server and gave it a static IP address range (172.19.1.2 through 172.19.1.254) to serve the clients. First I thought I could use DHCP to assign the addresses, but I cannot use DHCP in my LAN connection (not allowed by the hosting service). I tried configuring DHCP binding it to a Microsoft Loopback Adapter, but that's not supported as a DHCP source by RRAS. What I want to accomplish is to send specific DHCP options to the client (network mask, routing table, etc.). In particular: Prevent the client from having the server as default router (without changing the client's "use default gateway in remote network"). Have it as a route for the server's internal RRAS address only (172.19.1.1). Prevent the client from using a 255.255.0.0 mask for the 172.19.x.x network (a 255.255.255.0 mask would be better). Can I do that with RRAS only? How? Currently, the only solution I can think of is to use DHCP in the LAN adapter, but filter DHCP packets so they don't reach the provider's network. However, I'm not sure if that will work. Any suggestions are welcomed! Guille

  Read the article

• Effects of HTTP/TCP connection handshakes and server performance

  - by Blankman

  When running apache bench on the same server as the website like: ab -n 1000 -c 10 localhost:8080/ I am most probably not getting accurate results when compared to users hitting the server from various locations. I'm trying to understand how or rather why this will effect real world performance since a user in china will have different latency issues when compared to someone in the same state/country. Say my web server has a maximum thread limit of 100. Can someone explain in detail how end user latency can/will effect server performance. I'm assuming here that each request will be computed equally at say 10ms. What I'm not understand is how external factors can effect overal server performance, specifically internet connections (location, or even device like mobile) and http/tcp handshakes etc.

  Read the article

• BAD DC transfering FSMO Roles to ADC

  - by Suleman

  I have a DC (FQDN:server.icmcpk.local) and an ADC (FQDN:file-server.icmcpk.local). Recently my DC is facing a bad sector problem so I changed the Operation Masters to file-server for all five roles. but when ever i turn off the OLD DC the file-server also stops wroking with AD and GPMC further i m also unable to join any other computer to this domain. For Test purpose i also added a new ADC (FQDN:wds-server.icmcpk.local) but no succes with the old DC off i had to turn the old DC on and then joined it. I m attaching the Dcdiags for all three servers. Kindly help me so that i b able to reinstall new HDD and it can go online again. --------------------------------------- Server --------------------------------------- C:\Program Files\Support Tools>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\SERVER Starting test: Connectivity ......................... SERVER passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\SERVER Starting test: Replications [Replications Check,SERVER] A recent replication attempt failed: From FILE-SERVER to SERVER Naming Context: DC=ForestDnsZones,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From WDS-SERVER to SERVER Naming Context: DC=ForestDnsZones,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From FILE-SERVER to SERVER Naming Context: DC=DomainDnsZones,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From WDS-SERVER to SERVER Naming Context: DC=DomainDnsZones,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From FILE-SERVER to SERVER Naming Context: CN=Schema,CN=Configuration,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From WDS-SERVER to SERVER Naming Context: CN=Schema,CN=Configuration,DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. [Replications Check,SERVER] A recent replication attempt failed: From WDS-SERVER to SERVER Naming Context: DC=icmcpk,DC=local The replication generated an error (1908): Could not find the domain controller for this domain. The failure occurred at 2012-05-04 14:07:13. The last success occurred at 2012-05-04 13:48:39. 1 failures have occurred since the last success. Kerberos Error. A KDC was not found to authenticate the call. Check that sufficient domain controllers are available. ......................... SERVER passed test Replications Starting test: NCSecDesc ......................... SERVER passed test NCSecDesc Starting test: NetLogons ......................... SERVER passed test NetLogons Starting test: Advertising ......................... SERVER passed test Advertising Starting test: KnowsOfRoleHolders ......................... SERVER passed test KnowsOfRoleHolders Starting test: RidManager ......................... SERVER passed test RidManager Starting test: MachineAccount ......................... SERVER passed test MachineAccount Starting test: Services ......................... SERVER passed test Services Starting test: ObjectsReplicated ......................... SERVER passed test ObjectsReplicated Starting test: frssysvol ......................... SERVER passed test frssysvol Starting test: frsevent There are warning or error events within the last 24 hours after the SYSVOL has been shared. Failing SYSVOL replication problems may cause Group Policy problems. ......................... SERVER failed test frsevent Starting test: kccevent ......................... SERVER passed test kccevent Starting test: systemlog An Error Event occured. EventID: 0x80001778 Time Generated: 05/04/2012 14:05:39 Event String: The previous system shutdown at 1:26:31 PM on An Error Event occured. EventID: 0x825A0011 Time Generated: 05/04/2012 14:07:45 (Event String could not be retrieved) An Error Event occured. EventID: 0x00000457 Time Generated: 05/04/2012 14:13:40 (Event String could not be retrieved) An Error Event occured. EventID: 0x00000457 Time Generated: 05/04/2012 14:14:25 (Event String could not be retrieved) An Error Event occured. EventID: 0x00000457 Time Generated: 05/04/2012 14:14:25 (Event String could not be retrieved) An Error Event occured. EventID: 0x00000457 Time Generated: 05/04/2012 14:14:38 (Event String could not be retrieved) An Error Event occured. EventID: 0xC1010020 Time Generated: 05/04/2012 14:16:14 Event String: Dependent Assembly Microsoft.VC80.MFCLOC could An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:16:14 Event String: Resolve Partial Assembly failed for An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:16:14 Event String: Generate Activation Context failed for An Error Event occured. EventID: 0xC1010020 Time Generated: 05/04/2012 14:16:14 Event String: Dependent Assembly Microsoft.VC80.MFCLOC could An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:16:14 Event String: Resolve Partial Assembly failed for An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:16:14 Event String: Generate Activation Context failed for An Error Event occured. EventID: 0x825A0011 Time Generated: 05/04/2012 14:22:57 (Event String could not be retrieved) An Error Event occured. EventID: 0xC1010020 Time Generated: 05/04/2012 14:22:59 Event String: Dependent Assembly Microsoft.VC80.MFCLOC could An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:22:59 Event String: Resolve Partial Assembly failed for An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:22:59 Event String: Generate Activation Context failed for An Error Event occured. EventID: 0xC1010020 Time Generated: 05/04/2012 14:22:59 Event String: Dependent Assembly Microsoft.VC80.MFCLOC could An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:22:59 Event String: Resolve Partial Assembly failed for An Error Event occured. EventID: 0xC101003B Time Generated: 05/04/2012 14:22:59 Event String: Generate Activation Context failed for ......................... SERVER failed test systemlog Starting test: VerifyReferences ......................... SERVER passed test VerifyReferences Running partition tests on : ForestDnsZones Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Starting test: CheckSDRefDom ......................... ForestDnsZones passed test CheckSDRefDom Running partition tests on : DomainDnsZones Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Starting test: CheckSDRefDom ......................... DomainDnsZones passed test CheckSDRefDom Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : icmcpk Starting test: CrossRefValidation ......................... icmcpk passed test CrossRefValidation Starting test: CheckSDRefDom ......................... icmcpk passed test CheckSDRefDom Running enterprise tests on : icmcpk.local Starting test: Intersite ......................... icmcpk.local passed test Intersite Starting test: FsmoCheck ......................... icmcpk.local passed test FsmoCheck ---------------------- File-Server ---------------------- C:\Users\Administrator.ICMCPK>dcdiag Directory Server Diagnosis Performing initial setup: Trying to find home server... Home Server = FILE-SERVER * Identified AD Forest. Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\FILE-SERVER Starting test: Connectivity ......................... FILE-SERVER passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\FILE-SERVER Starting test: Advertising Warning: DsGetDcName returned information for \\Server.icmcpk.local, when we were trying to reach FILE-SERVER. SERVER IS NOT RESPONDING or IS NOT CONSIDERED SUITABLE. ......................... FILE-SERVER failed test Advertising Starting test: FrsEvent ......................... FILE-SERVER passed test FrsEvent Starting test: DFSREvent ......................... FILE-SERVER passed test DFSREvent Starting test: SysVolCheck ......................... FILE-SERVER passed test SysVolCheck Starting test: KccEvent ......................... FILE-SERVER passed test KccEvent Starting test: KnowsOfRoleHolders ......................... FILE-SERVER passed test KnowsOfRoleHolders Starting test: MachineAccount ......................... FILE-SERVER passed test MachineAccount Starting test: NCSecDesc Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have Replicating Directory Changes In Filtered Set access rights for the naming context: DC=ForestDnsZones,DC=icmcpk,DC=local Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have Replicating Directory Changes In Filtered Set access rights for the naming context: DC=DomainDnsZones,DC=icmcpk,DC=local ......................... FILE-SERVER failed test NCSecDesc Starting test: NetLogons Unable to connect to the NETLOGON share! (\\FILE-SERVER\netlogon) [FILE-SERVER] An net use or LsaPolicy operation failed with error 67, The network name cannot be found.. ......................... FILE-SERVER failed test NetLogons Starting test: ObjectsReplicated ......................... FILE-SERVER passed test ObjectsReplicated Starting test: Replications ......................... FILE-SERVER passed test Replications Starting test: RidManager ......................... FILE-SERVER passed test RidManager Starting test: Services ......................... FILE-SERVER passed test Services Starting test: SystemLog An Error Event occurred. EventID: 0x00000469 Time Generated: 05/04/2012 14:01:10 Event String: The processing of Group Policy failed because of lack of network con nectivity to a domain controller. This may be a transient condition. A success m essage would be generated once the machine gets connected to the domain controll er and Group Policy has succesfully processed. If you do not see a success messa ge for several hours, then contact your administrator. An Warning Event occurred. EventID: 0x8000A001 Time Generated: 05/04/2012 14:07:11 Event String: The Security System could not establish a secured connection with th e server ldap/icmcpk.local/[email protected]. No authentication protocol was available. An Warning Event occurred. EventID: 0x00000BBC Time Generated: 05/04/2012 14:30:34 Event String: Windows Defender Real-Time Protection agent has detected changes. Mi crosoft recommends you analyze the software that made these changes for potentia l risks. You can use information about how these programs operate to choose whet her to allow them to run or remove them from your computer. Allow changes only if you trust the program or the software publisher. Windows Defender can't undo changes that you allow. An Warning Event occurred. EventID: 0x00000BBC Time Generated: 05/04/2012 14:30:36 Event String: Windows Defender Real-Time Protection agent has detected changes. Mi crosoft recommends you analyze the software that made these changes for potentia l risks. You can use information about how these programs operate to choose whet her to allow them to run or remove them from your computer. Allow changes only if you trust the program or the software publisher. Windows Defender can't undo changes that you allow. ......................... FILE-SERVER failed test SystemLog Starting test: VerifyReferences ......................... FILE-SERVER passed test VerifyReferences Running partition tests on : ForestDnsZones Starting test: CheckSDRefDom ......................... ForestDnsZones passed test CheckSDRefDom Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Running partition tests on : DomainDnsZones Starting test: CheckSDRefDom ......................... DomainDnsZones passed test CheckSDRefDom Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Running partition tests on : Schema Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Running partition tests on : Configuration Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Running partition tests on : icmcpk Starting test: CheckSDRefDom ......................... icmcpk passed test CheckSDRefDom Starting test: CrossRefValidation ......................... icmcpk passed test CrossRefValidation Running enterprise tests on : icmcpk.local Starting test: LocatorCheck ......................... icmcpk.local passed test LocatorCheck Starting test: Intersite ......................... icmcpk.local passed test Intersite --------------------- WDS-Server --------------------- C:\Users\Administrator.ICMCPK>dcdiag Directory Server Diagnosis Performing initial setup: Trying to find home server... Home Server = WDS-SERVER * Identified AD Forest. Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\WDS-SERVER Starting test: Connectivity ......................... WDS-SERVER passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\WDS-SERVER Starting test: Advertising Warning: DsGetDcName returned information for \\Server.icmcpk.local, when we were trying to reach WDS-SERVER. SERVER IS NOT RESPONDING or IS NOT CONSIDERED SUITABLE. ......................... WDS-SERVER failed test Advertising Starting test: FrsEvent There are warning or error events within the last 24 hours after the SYSVOL has been shared. Failing SYSVOL replication problems may cause Group Policy problems. ......................... WDS-SERVER passed test FrsEvent Starting test: DFSREvent ......................... WDS-SERVER passed test DFSREvent Starting test: SysVolCheck ......................... WDS-SERVER passed test SysVolCheck Starting test: KccEvent ......................... WDS-SERVER passed test KccEvent Starting test: KnowsOfRoleHolders ......................... WDS-SERVER passed test KnowsOfRoleHolders Starting test: MachineAccount ......................... WDS-SERVER passed test MachineAccount Starting test: NCSecDesc Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have Replicating Directory Changes In Filtered Set access rights for the naming context: DC=ForestDnsZones,DC=icmcpk,DC=local Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have Replicating Directory Changes In Filtered Set access rights for the naming context: DC=DomainDnsZones,DC=icmcpk,DC=local ......................... WDS-SERVER failed test NCSecDesc Starting test: NetLogons Unable to connect to the NETLOGON share! (\\WDS-SERVER\netlogon) [WDS-SERVER] An net use or LsaPolicy operation failed with error 67, The network name cannot be found.. ......................... WDS-SERVER failed test NetLogons Starting test: ObjectsReplicated ......................... WDS-SERVER passed test ObjectsReplicated Starting test: Replications ......................... WDS-SERVER passed test Replications Starting test: RidManager ......................... WDS-SERVER passed test RidManager Starting test: Services ......................... WDS-SERVER passed test Services Starting test: SystemLog An Error Event occurred. EventID: 0x0000041E Time Generated: 05/04/2012 14:02:55 Event String: The processing of Group Policy failed. Windows could not obtain the name of a domain controller. This could be caused by a name resolution failure. Verify your Domain Name Sysytem (DNS) is configured and working correctly. An Error Event occurred. EventID: 0x0000041E Time Generated: 05/04/2012 14:08:33 Event String: The processing of Group Policy failed. Windows could not obtain the name of a domain controller. This could be caused by a name resolution failure. Verify your Domain Name Sysytem (DNS) is configured and working correctly. ......................... WDS-SERVER failed test SystemLog Starting test: VerifyReferences ......................... WDS-SERVER passed test VerifyReferences Running partition tests on : ForestDnsZones Starting test: CheckSDRefDom ......................... ForestDnsZones passed test CheckSDRefDom Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Running partition tests on : DomainDnsZones Starting test: CheckSDRefDom ......................... DomainDnsZones passed test CheckSDRefDom Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Running partition tests on : Schema Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Running partition tests on : Configuration Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Running partition tests on : icmcpk Starting test: CheckSDRefDom ......................... icmcpk passed test CheckSDRefDom Starting test: CrossRefValidation ......................... icmcpk passed test CrossRefValidation Running enterprise tests on : icmcpk.local Starting test: LocatorCheck ......................... icmcpk.local passed test LocatorCheck Starting test: Intersite ......................... icmcpk.local passed test Intersite

  Read the article

• repeated failing passwords in linux security log (/var/log/secure)

  - by wallyk

  Recently, I opened up the SSH port through my firewalls (and redirecting to my server) so I could check on the (http) server while on the road. The first week or two there was nothing different. But now, three or four weeks later, I see lots of this: Mar 20 08:38:28 localhost sshd[21895]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=mail.queued.net user=root Mar 20 08:38:31 localhost sshd[21895]: Failed password for root from 207.210.101.209 port 2854 ssh2 Mar 20 15:38:31 localhost sshd[21896]: Received disconnect from 207.210.101.209: 11: Bye Bye Mar 20 08:38:32 localhost unix_chkpwd[21900]: password check failed for user (root) Mar 20 08:38:32 localhost sshd[21898]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=mail.queued.net user=root Mar 20 08:38:34 localhost sshd[21898]: Failed password for root from 207.210.101.209 port 3729 ssh2 Mar 20 15:38:35 localhost sshd[21899]: Received disconnect from 207.210.101.209: 11: Bye Bye Mar 20 08:38:36 localhost unix_chkpwd[21903]: password check failed for user (root) Mar 20 08:38:36 localhost sshd[21901]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=mail.queued.net user=root Mar 20 08:38:38 localhost sshd[21901]: Failed password for root from 207.210.101.209 port 4313 ssh2 Mar 20 15:38:38 localhost sshd[21902]: Received disconnect from 207.210.101.209: 11: Bye Bye Mar 20 08:38:40 localhost unix_chkpwd[21906]: password check failed for user (root) Mar 20 08:38:40 localhost sshd[21904]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=mail.queued.net user=root Mar 20 08:38:42 localhost sshd[21904]: Failed password for root from 207.210.101.209 port 4869 ssh2 Mar 20 15:38:43 localhost sshd[21905]: Received disconnect from 207.210.101.209: 11: Bye Bye Mar 20 08:38:44 localhost unix_chkpwd[21909]: password check failed for user (root) Mar 20 08:38:44 localhost sshd[21907]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=mail.queued.net user=root Mar 20 08:38:46 localhost sshd[21907]: Failed password for root from 207.210.101.209 port 2512 ssh2 Mar 20 15:38:47 localhost sshd[21908]: Received disconnect from 207.210.101.209: 11: Bye Bye Mar 20 15:38:57 localhost sshd[21912]: Connection closed by 207.210.101.209 There are about 1100 lines of these for March 20th, zero for the 19th, and 800 or so for the 18th—all related to the same IP. What does it mean? What should I do? Why isn't it chronological?

  Read the article

• Connecting a limited user to win server 2003 through LogMeIn

  - by Jeff

  Logmein support can't help me, maybe someone here can. I have a user on a windows 2003 server (non administrator). When I first created him and tried to connect through remote desktop I got the error "The local policy of the system does not permit you to logon interactively." I looked up the error and saw that this user was not a member of the Remote Desktop Users group. I added him to the group and was able to remote desktop in just fine. Then I tried to connect this user to the server through LogMeIn (pro trial version). I got the same error as when the user was not a part of the Remote Desktop Users group ("The local policy of the system does not permit you to logon interactively."). Can anyone tell me any other groups the user must be a member of in order to be allowed access through LogMeIn? I would image this is a common requirement logmein support seemed to have no idea.

  Read the article

• Tomcat 7 on Ubuntu 12.04 startup issues

  - by Nico Huysamen

  I am having trouble getting tomcat 7 to start up on my new VPS. I am really scratching my head since I have done this often. So I'm thinking it might be the VPS. I just got a new VPS from CINFU. After a clean install of Ubuntu 12.04 32bit, I install openjdk-6-jdk, update JAVA_HOME to point to: /usr/lib/jvm/java-1.6.0-openjdk-i386 and JRE_HOME to: /usr/lib/jvm/java-1.6.0-openjdk-i386/jre But when I try to run: ./catalina.sh run it simply outputs: Using CATALINA_BASE: /opt/tomcat/apache-tomcat-7.0.29 Using CATALINA_HOME: /opt/tomcat/apache-tomcat-7.0.29 Using CATALINA_TMPDIR: /opt/tomcat/apache-tomcat-7.0.29/temp Using JRE_HOME: /usr/lib/jvm/java-1.6.0-openjdk-i386 Using CLASSPATH: /opt/tomcat/apache-tomcat-7.0.29/bin/bootstrap.jar:/opt/tomcat/apache-tomcat-7.0.29/bin/tomcat-juli.jar and stops. It just hangs there doing nothing. If I run ./startup.sh && tail -f ../logs/catalina.out it gets to: Aug 24, 2012 8:38:36 PM org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["http-bio-8080"] Aug 24, 2012 8:38:36 PM org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["ajp-bio-8009"] Aug 24, 2012 8:38:36 PM org.apache.catalina.startup.Catalina load INFO: Initialization processed in 495 ms Aug 24, 2012 8:38:36 PM org.apache.catalina.core.StandardService startInternal INFO: Starting service Catalina Aug 24, 2012 8:38:36 PM org.apache.catalina.core.StandardEngine startInternal INFO: Starting Servlet Engine: Apache Tomcat/7.0.29 but I am unable to access anything. The request just hangs. I have also tried a few other things like explicitly exporting the paths etc in catalina.sh, and running ./startup.sh rather than catalina.sh, but the furthest I have gotten is that it finishes deploying all the WARs (the default ones that comes with tomcat like the host-manager etc), but then it hangs: Aug 24, 2012 8:47:30 PM org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["http-bio-8080"] and does nothing. Anyone have any pointers that might help? As I said, I must really be missing something stupid since this has worked on all other VPSs that we have. UPDATE I figured out that the problem is actually the fact that they use OpnVZ virtualization and that there are known compatibility problems with Java.

  Read the article

• Cacti not working for SNMP data sources

  - by lorenzo-s

  I installed packages cacti and snmpd on a Debian server. I'm able to display common graphs in Cacti (such as memory usage, load average, logged in users, etc) using the data templates listed as Unix. Now I want to replace these graphs with new ones using SNMP data sources, because I see there is also CPU usage and because it's not excluded I have to manage multiple hosts in the future. So, I installed snmpd on the machine and left the snmpd.conf as it is. In Cacti, I created three new data sources from SNMP templates for 127.0.0.1 host: ucd/net - CPU Usage - Nice ucd/net - CPU Usage - System ucd/net - CPU Usage - User Then I created a new graph from template ucd/net - CPU Usage, and select the three data sources in the Graph Item Fields section. Graph is now enabled and running, but empty. No data have been collected. Under Console - Devices my SNMP host is listed as up and running: System:Linux ip-xx-xx-xxx-xxx 3.2.0-23-virtual #36-Ubuntu SMP Tue Apr 10 22:29:03 UTC 2012 x86_64 Uptime: 929267 (0 days, 2 hours, 34 minutes) Hostname: ip-xx-xx-xxx-xxx Location: Sitting on the Dock of the Bay Contact: Me [email protected] In SNMP Options I left all as it is: SNMP Version: Version 1 SNMP Community: public SNMP Timeout: 500 ms Maximum OID's Per Get Request: 10 In Console - Utilities - Cacti Log I have multiple warning (two for each data source) every 5 minutes: 10/29/2012 01:45:01 PM - CMDPHP: Poller[0] Host[2] DS[18] WARNING: Result from SNMP not valid. Partial Result: U 10/29/2012 01:45:01 PM - CMDPHP: Poller[0] WARNING: SNMP Get Timeout for Host:'127.0.0.1', and OID:'.1.3.6.1.4.1.2021.4.15.0' 10/29/2012 01:45:01 PM - CMDPHP: Poller[0] Host[1] DS[9] WARNING: Result from SNMP not valid. Partial Result: U 10/29/2012 01:45:01 PM - CMDPHP: Poller[0] WARNING: SNMP Get Timeout for Host:'127.0.0.1', and OID:'.1.3.6.1.4.1.2021.11.52.0' 10/29/2012 01:40:01 PM - CMDPHP: Poller[0] Host[2] DS[19] WARNING: Result from SNMP not valid. Partial Result: U 10/29/2012 01:40:01 PM - CMDPHP: Poller[0] WARNING: SNMP Get Timeout for Host:'127.0.0.1', and OID:'.1.3.6.1.4.1.2021.4.6.0' [...] I have the feeling I'm missing something, but I cannot get it...

  Read the article

• MySQL, replacing &nbsp; with... nothing (delete those, please!)

  - by javipas

  I'm trying to purge my WordPress content from "false" carriage return (CR). These are caused after a migration of my content, that now presents from time to time a &nbsp; code that makes the web rendering engine to "paint" a CR where I would like to be nothing. The paragraphs seem to have a double CR because of this, and look too far apart. I'd like to be able to make a MySQL query in order to get rid of that strings, but at the moment I haven't found the key. What I've tried is UPDATE wp_posts set post_content = replace (post_content,'&nbsp;',' '); But i get <p> </p> where before were the &nbsp; strings. This seems not the answer at all. Could it have to be with the ampersand, and in that case, should I use something like &amp;nbsp; or something similar?

  Read the article

• Kerberos & signle-sign-on for website

  - by Dylan Klomparens

  I have a website running on a Linux computer using Apache. I've employed mod_auth_kerb for single-sign-on Kerberos authentication against a Windows Active Directory server. In order for Kerberos to work correctly, I've created a service account in Active Directory called dummy. I've generated a keytab for the Linux web server using ktpass.exe on the Windows AD server using this command: ktpass /out C:\krb5.keytab /princ HTTP/[email protected] /mapuser [email protected] /crypto RC4-HMAC-NT /ptype KRB5_NT_PRINCIPAL /pass xxxxxxxxx I can successfully get a ticket from the Linux web server using this command: kinit -k -t /path/to/keytab HTTP/[email protected] ... and view the ticket with klist. I have also configured my web server with these Kerberos properties: <Directory /> AuthType Kerberos AuthName "Example.com Kerberos domain" KrbMethodK5Passwd Off KrbAuthRealms EXAMPLE.COM KrbServiceName HTTP/[email protected] Krb5KeyTab /path/to/keytab Require valid-user SSLRequireSSL <Files wsgi.py> Order deny,allow Allow from all </Files> </Directory> However, when I attempt to log in to the website (from another Desktop with username 'Jeff') my Kerberos credentials are not automatically accepted by the web server. It should grant me access immediately after that, but it does not. The only information I get from the mod_auth_kerb logs is: kerb_authenticate_user entered with user (NULL) and auth_type Kerberos However, more information is revealed when I change the mod_auth_kerb setting KrbMethodK5Passwd to On: [Fri Oct 18 17:26:44 2013] [debug] src/mod_auth_kerb.c(1939): [client xxx.xxx.xxx.xxx] kerb_authenticate_user entered with user (NULL) and auth_type Kerberos [Fri Oct 18 17:26:44 2013] [debug] src/mod_auth_kerb.c(1031): [client xxx.xxx.xxx.xxx] Using HTTP/[email protected] as server principal for password verification [Fri Oct 18 17:26:44 2013] [debug] src/mod_auth_kerb.c(735): [client xxx.xxx.xxx.xxx] Trying to get TGT for user [email protected] [Fri Oct 18 17:26:44 2013] [debug] src/mod_auth_kerb.c(645): [client xxx.xxx.xxx.xxx] Trying to verify authenticity of KDC using principal HTTP/[email protected] [Fri Oct 18 17:26:44 2013] [debug] src/mod_auth_kerb.c(1110): [client xxx.xxx.xxx.xxx] kerb_authenticate_user_krb5pwd ret=0 [email protected] authtype=Basic What am I missing? I've studied a lot of online tutorials and cannot find a reason why the Kerberos credentials are not allowing access.

  Read the article

• Proxy settings: Allowed hosts instead of ignored hosts

  - by tapir

  I'm using Ubuntu, as many proxy applications, GNOME Network Proxy Preferences only allow to ignore hosts. What I want to do is exactly the opposite. I only want to use the proxy for few sites. Is it possible to define only the allowed hosts in any way? PS: I know FoxyProxy add-on for Firefox does this, but 1)I don't use Firefox and 2)I want the proxy settings system wide not only for browser.

  Read the article

• Apache mod-pagespeed installation affects mod-spdy?

  - by tim peterson

  Recently my site (an https connection, running on an Amazon EC2 ubuntu apache2.2) has this issue where I need to load the page several times (3-4) before it will load normally without issue. It will then load normally as long as I keep loading pages regularly (every couple seconds). It will stall again if I don't load pages for a few minutes. It has nothing to do with my application because I don't have this problem with the exact same app codebase on my Apache installation on my laptop. The only things to my knowledge that I've changed is that I recently installed mod_spdy and then a few weeks later I installed mod_pagespeed, https://developers.google.com/speed/pagespeed/mod. However, I have since turned mod_pagespeed off by setting its pagespeed.conf to mod_pagespeed off. Unfortunately, that didn't solve the problem. The line below is how every of last 10 lines of my error.log look: # tail -f /var/log/apache2/error.log ... [32728:32729:ERROR:mod_spdy.cc(162)] request->chunked == 1 in request GET / HTTP/1.1 [Sat Jun 02 04:50:08 2012] [warn] [client 50.136.93.153] [stream 5] [32728:32729:WARNING:http_to_spdy_filter.cc(113)] HttpToSpdyFilter is not the last filter in the chain: chunk any thoughts? thank you, tim

  Read the article

• SQL Server 2008 Logshipping not Restoring

  - by Nai

  I am getting the following errors during the restore part of the Logshipping process on my secondary server: 2010-04-01 10:00:01.85 Error: The file 'F:\UK_20100327090001.trn' is too recent to apply to the secondary database 'UK_Backup'.(Microsoft.SqlServer.Management.LogShipping) 2010-04-01 10:00:01.85 Error: The log in this backup set begins at LSN 55408000007387500001, which is too recent to apply to the database. An earlier log backup that includes LSN 55147000001788900001 can be restored. RESTORE LOG is terminating abnormally.(.Net SqlClient Data Provider) 2010-04-01 10:00:01.87 Searching for an older log backup file. Secondary Database: 'UK_Backup' 2010-04-01 10:00:01.90 Skipped log backup file. Secondary DB: 'UK_Backup', File: 'F:\UK_20100324090000.trn' 2010-04-01 10:00:01.93 Error: Could not find a log backup file that could be applied to secondary database 'UK_Backup'.(Microsoft.SqlServer.Management.LogShipping) 2010-04-01 10:00:01.93 Deleting old log backup files. Primary Database: 'UK' 2010-04-01 10:00:01.96 The restore operation completed with errors. Secondary ID: 'c066bb63-930c-4b73-861c-f59f0a38c12c' It was happily humming along until I checked it this morning. Some additional details. In the Logshipping folder, there is one file UK_20100324090001.trn dated on the 2009-3-24. The next most recent .trn file is the UK_20100374090001.trn which is the file that was applied during the restore. Why is there an older trn file seemingly on it's own? How can I fix this problem? It'll be a real pain to restart the entire logshipping process. x_x

  Read the article

• Looking for a webhost to support SSRS Hosting with SQL Azure

  - by Adrian Grigore

  Since SQL Azure does not currently support SSRS, the only possible workaround is to host my own SSRS server and have it point to my SQL Azure instance for data retrieval. Now, for me it would be total overkill to rent a dedicated server with SQL server on it just for hosting SSRS. Are there any (shared) web hosters that offer SSRS hosting with third party SQL servers? I've already asked discountasp.net, but they don't allow this. Thanks, Adrian

  Read the article

• Intermittent Connection Issues to SQL Server 2008 R2 RTM

  - by Chandan Jha

  The problem I am facing is a very complex one and inspite of trying to gather a root cause of the problem, I am standing at the same place after 2 months with just bits and pieces of information.Here is a scenario: There is a windows 2003 server which uses an system DSN ODBC connection. I looked into the driver properties and it is as follows: Name Version File SQL Server 2000.86.3959.00 SQLSRV32.DLL Now, this system DSN has been given configured with TCP\IP in Network Libraries and 'determine port dynamically' is checked. Now, lets come to the database destination. It is hosted on Windows 2008 having SQL 2008 R2 RTM version 64-bit. Now, I will give you a an overview about the events that happen and whatever troubleshooting I could perform: I get an email saying 'blah blah' failed and the only message their application gets is 'cannot connect to database' I go the SQL Server logs and find the following information: Login failed for user ''. Reason: An attempt to login using SQL authentication failed. Server is configured for Windows authentication only. [CLIENT: 10.0.0.xx Error: 18456, Severity: 14, State: 58.] A quick search shows that this error may come when an SQL Server is configured with windows authentication but its not true. We have mixed mode and connection issue is intermittent. This SQL Server is configured to run on a local system account but since we use only SQL Server accounts to connect to this, there should not be any Kerberos errors. When I run a profiler trace and see only 'existing connections', i see a lot of them coming from my client server displaying the sql user but NO hostname is shown. Textdata field shows TCP\IP information along with some arithabort and ansi-null settings. Now, I tried looking into ring connectivity buffer by using following: SELECTCAST(record AS XML) FROM sys.dm_os_ring_buffers WHERE ring_buffer_type = 'RING_BUFFER_CONNECTIVITY' One sample output is: <ConnectivityTraceRecord> <RecordType>Error</RecordType> <RecordSource>Tds</RecordSource> <Spid>118</Spid> <SniConnectionId>5124905D-D1EC-460E-AD78-201050B78C67</SniConnectionId> <OSError>0</OSError> <SniConsumerError>18452</SniConsumerError> <SniProvider>7</SniProvider> <State>1</State> <RemoteHost>10.0.0.21</RemoteHost> <RemotePort>5008</RemotePort> <LocalHost>10.1.0.38</LocalHost> <LocalPort>1433</LocalPort> <RecordTime>6/6/2012 21:14:57.527</RecordTime> <TdsBuffersInformation> <TdsInputBufferError>0</TdsInputBufferError> <TdsOutputBufferError>0</TdsOutputBufferError> <TdsInputBufferBytes>120</TdsInputBufferBytes> </TdsBuffersInformation> <TdsDisconnectFlags> <PhysicalConnectionIsKilled>0</PhysicalConnectionIsKilled> <DisconnectDueToReadError>0</DisconnectDueToReadError> <NetworkErrorFoundInInputStream>0</NetworkErrorFoundInInputStream> <ErrorFoundBeforeLogin>0</ErrorFoundBeforeLogin> <SessionIsKilled>0</SessionIsKilled> <NormalDisconnect>0</NormalDisconnect> </TdsDisconnectFlags> </ConnectivityTraceRecord> <Stack> <frame id="0">0X000000000174C34B</frame> <frame id="1">0X0000000001748FDD</frame> <frame id="2">0X0000000002461001</frame> <frame id="3">0X0000000000C47E98</frame> <frame id="4">0X00000000008015AD</frame> <frame id="5">0X0000000000801492</frame> <frame id="6">0X00000000003CBBD8</frame> <frame id="7">0X00000000003CB8BA</frame> <frame id="8">0X00000000003CB6FF</frame> <frame id="9">0X00000000008E8FB6</frame> <frame id="10">0X00000000008E9175</frame> <frame id="11">0X00000000008E9839</frame> <frame id="12">0X00000000008E9502</frame> <frame id="13">0X0000000074E437D7</frame> <frame id="14">0X0000000074E43894</frame> <frame id="15">0X00000000775A652D</frame> Somehow all the errors show error number 18452 whereas I never found this error in my SQL logs where I see only 18456. I am just stuck on a dead end because this connection issue appears intermittently. Sorry for a long question but I hope if you read this, you can make out that I tried a lot at my end before giving up.

  Read the article

• VPN IP Routing - slow connections

  - by dannymcc

  UPDATE: Router error logs show: LCP Time-out 0 I'm not sure how to correct this. The Lan-to-Lan profiles are set to -1 Idle Timeout (for the remote branch). I have a PPTP VPN running between two Draytek 2820 routers. They are setup that one dials out to the other one. Main Practice - 192.168.1.0/24 Branch - 192.168.3.0/24 I have then set (on the Branch) router the following route: 192.168.1.0/24 If I then request a server running on 192.168.1.1 from the Branch, it correctly routes through VPN tunnel. If I request the branch server at 192.168.3.1 it correctly routes to the local server without using the VPN tunnel. I have temporarily disabled the firewall on both routers, and made sure that QoS is disabled. The Main Practice internet connection is ~30mb down / ~10mb up, and the Branch connection is ~5mb down / ~2mb up. Anything over the VPN tunnel runs pretty slowly (VNC, Remote Desktop and Terminal Emulators). However, if I dial using the Windows VPN wizard, creating a connection from the laptop to the Main Practice - everything runs quickly. I'm looking for possible causes, and/or ways of further diagnosing the issue. Any help would be greatly appreciated! UPDATE: In summary, when I connect within the Branch and try and access a host that's within the Main Practice it works, but slowly. If I then dial the VPN on my Windows 7 laptop whilst still connected to the Branch network, it's fast. Main Practice Branch Practice Routing Table from Branch Router Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 126.256.126.103 WAN2 C~ 192.168.1.99/ 255.255.255.255 directly connected VPN-1 S~ 192.168.1.0/ 255.255.255.0 via 192.168.1.99 VPN-1 S~ 192.168.2.0/ 255.255.255.0 via 192.168.1.99 VPN-1 C~ 192.168.3.0/ 255.255.255.0 directly connected LAN2 C 126.256.126.103/ 255.255.255.224 directly connected WAN2 Routing Table from Main Practice Key: C - connected, S - static, R - RIP, * - default, ~ - private * 0.0.0.0/ 0.0.0.0 via 81.139.64.1, WAN2 S 81.137.176.1/ 255.255.255.255 via 81.137.176.1, WAN2 * 81.139.64.1/ 255.255.255.255 via 81.139.64.1, WAN2 C~ 192.168.1.204/ 255.255.255.255 is directly connected, VPN C~ 192.168.1.0/ 255.255.255.0 is directly connected, LAN S~ 192.168.2.0/ 255.255.255.0 via 192.168.1.204, VPN S~ 192.168.3.0/ 255.255.255.0 via 192.168.1.203, VPN Connection Details (from Branch Router) Connection Details (from Main Practice Router) IPERF.exe Output

  Read the article

• Unexpected results from custom partitioning scheme - Ubuntu preseed unattended install

  - by Mark Renouf

  Hi... I need some help with partman-auto custom recipe in preseed.... it's doing unexpected things, the docs aren't so clear. This is in my preseed file: d-i partman-auto/expert_recipe string \ boot-root-var :: \ 1024 100 1024 ext4 \ $primary{ } $bootable{ } \ method{ format } format{ } \ use_filesystem{ } filesystem{ ext4 } \ mountpoint{ /boot } \ . \ 2048 50 4096 ext4 \ method{ format } format{ } \ use_filesystem{ } filesystem{ ext4 } \ mountpoint{ / } \ . \ 4096 25 100000 ext4 \ method{ format } format{ } \ use_filesystem{ } filesystem{ ext4 } \ mountpoint{ /var } \ . \ 256 75 100% linux-swap \ method{ swap } format{ } \ . Given an 80GB drive. I ended up with these partitions: / 2GB /boot 1GB /var 4GB swap 72GB What went wrong? What I want is: / 2GB /boot 1GB /var 72GB swap 4GB

  Read the article

• Preventing access to files if a user types the full url on the address bar

  - by bogha

  i have a website, some folders on the websites contains images and files like .pdf , .doc and .docx . the user can easly just type the address in the url to get the file or display the photo http://site/folder1/img/pic1.jpg then boom.. he can see the image or just download the file my question is: how to prevent this kind of action, how can i guarantee a secure access of the files. any suggestions UPDATE TO CLARIFY MY IDEA i don't want any user who is browsing the website to get access to these files normally by just writing the URL of the file. those files are a CV files, they are being uploaded by the users to a specific folder on the server which we host outside the company. those files are only being viewed by the HR people through a special system. that's the scenario we want. i don't want a WEB GEEK who just wants to see what files has been uploaded to this folder to download them easly to his/her computer and view them or publish them on the internet. i hope you got my idea

  Read the article

• Error in applying patch in Apache

  - by newbie.my

  Recently i have installing apache 2.2.21 from the source for testing purpose. After doing clean installation of apache i want to patch it with the patches provided here: http://www.apache.org/dist/httpd/patches/ Anyway when i put the patch command as mention in the page it show this result: File to patch: CVE-2011-3368.patch 1 out of 1 hunk FAILED -- saving rejects to file CVE-2011-3368.patch.rej Is there something wrong with my patch?If not,how could i verified that the patch has been implemented or not?

  Read the article

• What is meant by "streaming data access" in HDFS?

  - by Van Gale

  According to the HDFS Architecture page HDFS was designed for "streaming data access". I'm not sure what that means exactly, but would guess it means an operation like seek is either disabled or has sub-optimal performance. Would this be correct? I'm interested in using HDFS for storing audio/video files that need to be streamed to browser clients. Most of the streams will be start to finish, but some could have a high number of seeks. Maybe there is another file system that could do this better?

  Read the article

• Setting up a Barracuda Spam Filter

  - by stead1984

  We have just purchased a Barracuda Spam Firewall 300, we have set it up but are having problems authenticating with our Exchange server (2007). I spoke to Barracuda about it and they said I need to exclude the Barracuda box from authentication from within Exchange, how do I do that?

  Read the article

< Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >