Search Results

Search found 9025 results on 361 pages for 'quad core'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 169/361 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

  • USB question (how durable is it, how should I workaround this)

    - by Shiki
    The plot is quite simple. Got a Razer mouse. If I plug it in, it works. After a shutdown/hibernation, I have to replug it entirely at the back of the PC. (It works in my laptop even after severel shutdown, etc, so yes I guess it's my motherboard.. but it still got 2 years of warranty and it comes with quad SLI, its not an old motherboard at all. (MSI P7N SLI FI (bought it after a hungarian guy's recommendation)). So. I only could come up with one "solution". Get 3 USB cable (you know, USB-USB). If its possible the shortest ones (don't know if the responsibility/anything will worsen), AND replug only the middle+closest to the USB port junction, since those are replaceable. What do you think? Any other idea? (BIOS is updated, mouse driver ... doesn't really matter, the mouse won't even blink a bit after this happens. It lights up and goes totally dead.)

    Read the article

  • Windows 7 starts getting sluggish over a few days

    - by munrobasher
    Myself and the other developer are running Windows 7 Enterprise 64 bit with 8GB RAM on different Gigabyte motherboards with Quad core Intel CPUs. Most of the time, it runs like a dream. We use VMware workstation a lot (hence the 8GB) and that works well. Except... now and then, after the PCs have been on for a few days, the whole system starts getting really sluggish doing certain tasks. The other's developer's system is far worse than mine with it taking up to a minute to launch IE. Today, mine has gone sluggish but nowhere near as bad. For example, normally when I click on a new tab in IE, it's instant. Today, there's an obvious delay. Right-clicking in this window to trigger iSpell is normally instant, right now it takes about five seconds. I've got resource monitor open on my second monitor and when I did that right-click, there was no obvious peak in CPU, disk or memory. A reboot does fix it so it does sound like a resource issue but haven't a clue what might be to blame. The two computers have similarities (same spec) but also differences (like motherboard, RAM & CPU models). So I guess the question is, any pointers on diagnosing why a PC is sluggish? What could cause such a right-click slow down in IE for example? It sounds like such a simple operation. NOTE: whilst typing this message alone, it was fine performance wise. I can click around the page no problem but right-click still is noticeable slow. Will reboot over lunch... Cheers, Rob.

    Read the article

  • Differences between Fedora servers

    - by Yarin
    I'm using Amazon EC2 and trying to choose a machine image (AMI) for my project. It seems all their LAMP AMIs are Fedora Core 4, but this seems like quite an old version, considering the current release is apparently Fedora 12, and < 10 releases are no longer supported. My question is how significantly different are the early fedora releases- is it crazy to be on versions 4 or even 8? (I realize this is probably a broad question)

    Read the article

  • Some Emails incoming to Outlook 2007 are blank, same emails work fine on webmail, iphone, etc

    - by Funran
    This is a pretty easy problem to describe. Basically users who have just been upgraded to Outlook 2007 (yeah I know 2010 is out), are not receiving SOME emails (from outside our domain, ie hotmail, yahoo). Receiving is not the correct word, these emails come in, along with their attachments, subjects, to/from line, etc. But the body is blank. If the same user goes into their webmail, iphone, blackberry instead, they can read the message fine. It's clear to me that something in Outlook 2007 is not generating the body correctly, so it just strips it. I just don't know WHY. Our mail server was recently upgraded to Exchange 2010, users on 2010 running outlook 2003 are working fine, it's just the random emails for users using 2007. I hope I made that clear enough, thank you for any future help guys. EDIT: I don't see rft, but i swear I've seen it before. Here is the view source on a recent email. <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN"><html><head> <meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1"> <meta name="GENERATOR" content="MSHTML 8.00.6001.19120"> <DEFANGED_style_0 <="" style=""> </head> <body bgcolor="#ffffff"> <p><DEFANGED_DIV><font color="#0000ff" size="2" face="Calibri">MS,</font></p><DEFANGED_DIV> <p><DEFANGED_DIV><font color="#0000ff" size="2" face="Calibri">Could you tell me please what the legal descrip &amp; Topo Quad name is for this Monroe P.ID Site?</font></p><DEFANGED_DIV> <p><DEFANGED_DIV><em><font color="#0000ff" size="2" face="Calibri">Thanks, Henry Roye</font></em></p><DEFANGED_DIV></body></html>

    Read the article

  • Why don't monitors have more pixels per inch?

    - by ULTRA_POROV
    72 ppi is nothing. And we have been stuck with this for 20 years. Why do we need to resort to stupid tech like anti-aliasing instead of resolving the core of the issue, more pixels per inch!!! It is really surprising considering all the progress cpu's, video cards, etc. have made.

    Read the article

  • Not able to connect to game using "Game Ranger"

    - by Daud
    Every time the game is about to start it says that I have lost my connection to EA's servers with the following message: Make sure your network adapter and network cable is plugged in. Although my connection works perfectly but when it comes to online gaming it messes up everything. My System specifications: Intel(R) Core(TM) i5-2410M CPU @ 2.30GHz 4096MB RAM Windows 7 Ultimate 64-bit Internet connection of 2Mbps Can you help me to sort it out?

    Read the article

  • Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

    - by Biohazard
    I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

    Read the article

  • How long will it take to create an OS backup image?

    - by user23950
    How much time will it take to backup 49GB? Here are the details: Windows 7 Dual core CPU 2.50 GHz 2GB memory I'll use the free version of Macrium Reflect. I will back it up to a Seagate portable hard-drive. I have installed: Microsoft Visual Studio 2008, NetBeans, and some CS4 Master Collection products. I only need to backup one partition.

    Read the article

  • Screen Flicker in Vista

    - by mario64
    I noticed everytime my dell inspiron 1420 wakes up from sleep the screen will flicker a lot. some times violently. I'm not sure what the problem is. I have disabled tmm but it didn't fix the flickers. Does anyone have a solution? Here's my spec: Dell Inspiron 1420 4GB RAM Intel Core 2 Duo T5750 Nvidia Geforce 8400MS Windows Vista 32bit

    Read the article

  • VMWare Pre-Allocated vs. Growable, which is faster?

    - by tekiegreg
    In an effort to increase speed in my Vmware setup, I was thinking about converting a Windows XP Guest 32 bit I have from growable to pre-allocated, I'm currently running VMWare Workstation 7 with Windows 7 64 bit as the host. Specs: Dual Core CPU, one allocated to guest 4GB of RAM, 2GB to guest HD max capacity is 500GB, 150GB allocated to guest (I have 300GB left and don't mind parting with the space, currently HD is 80GB and converting would obviously add another 70GB of space), HD that guest is running on is separate from Host OS Either that or any other suggestions you have might be appreciated, thanks!

    Read the article

  • Is there an objective way to measure slowness of PC/WINDOWS?

    - by ekms
    We've a lot of users that usually complain about that his PC is "slow". (we use win XP). We usually check startup programs, virus, fragmentation, disk health and common problems that causes slowness (Symantec AV drops disk to 1mb/s , or a seagate HD firmware error in certain models), but in those cases the slowness is pretty evident. In other hand, the most common is the user complaining about his pc but for us looks OK, even in 6 years old desktops. People sometimes even complains about his new quad core desktops speed!!! So, we are asking if there's a way to OBJECTIVELY check that a computer didn't dropped its performance, compared with similar ones o previous measures, specially for work use (I don't think that 3dmark benchmark o similar may help). The only thing that I found that was useful is HDTune, but it only check hard disk performance. Basically, what we want is something that enable us to say to our users "see? your PC is as slow as was three years ago! stop complaining! Is all in your head!"

    Read the article

  • Low-traffic WordPress website on Apache keeps crashing server

    - by OC2PS
    I have recently moved my low-moderate traffic (1000 UAUs, 5000 pageviews on a busy day) website from shared hosting to a Centos 6 64-bit VPS with Apache and cPanel running on 4 quad-core processor (likely oversold) and 3GB memory (Xen). We've had problems from the beginning. The server keeps crashing. It seems PHP keeps expanding till it consumes all the memory and crashes the server. Some folks have suggested that I should abandon Apache/cPanel/PHP/mySQL and go with nginX/Varnish/PHP-FPM/SQLite. But that's just not possible for me as I am not very tech savvy and need a simple GUI like cPanel to be able to manage the mundane management tasks (can't afford to hire system administrator or get fully managed hosting). I have come across several posts discussing optimization of Apache for WordPress. But all of these lead to articles that are pretty dated such as this ~4 year old one from Jan 2009 - http://thethemefoundry.com/blog/optimize-apache-wordpress/ The article is pretty detailed and seems helpful, but I stumble even on the first step. My httpd.conf only has 2 loadmodule commands LoadModule fastinclude_module modules/mod_fastinclude.so LoadModule bwlimited_module modules/mod_bwlimited.so So I go total bust right there. Further, my httpd.conf says Direct modifications to the Apache configuration file may be lost upon subsequent regeneration of the configuration file. To have modifications retained, all modifications must be checked into the configuration system by running: /usr/local/cpanel/bin/apache_conf_distiller I am having trouble finding where to change the modules in WHM. Please can someone help me with updated guidelines on how to optimize Apache for WordPress? Many thanks! P.S. The WordPress installation also has WP Super Cache installed. P.P.S. I also have phpBB, OpenCart, and Menalto Gallery installed.

    Read the article

  • Win7 Hangs During App Install/Upgrade/Uninstall

    - by JadeMason
    I have a custom built PC that intermittently hangs when installing, uninstalling, or upgrading applications. Technical Specs ASUS P5E w/ WiFi Motherboard Intel Core2 Quad Q6600 Processor 4x 2GB G.Skill DDR2 800 SDRAM ASUS EAH2900XT / Radeon HD 2900XT 512MB Video Card Under normal operation the machine runs reliably, even under heavy load, such as video transcoding. The temperature never gets anywhere near where I would worry about it. However, the machine regularly hangs (complete lockup, no response to keyboard or mouse, no activity on-screen) when either installing a new application, uninstalling an existing application, or applying patches to existing applications or the OS. This is extremely frustrating as this machine is primarily used as a HTPC. Several apps are configured for automatic updates, and these updates sometimes cause the machine to lockup while we are watching content on the PC. In previously investigating this issue, I found one likely problem could be my Logitech Webcam. The Logitech software has a bug that leaves an entry in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\ Control\SessionManager\PendingFileRenameOperations Which references the Temp directory. My registry contained this error, so I uninstalled the webcam software and deleted this registry key value. Unfortunately, the machine will still intermittently hang. I've noticed that the hangs always happen when an install/upgrade/uninstall requires elevated privileges (presumably to modify the registry). I can typically get at least one install/upgrade/uninstall to complete after a reboot, but after that it is a game of russian roulette to see if the operation will succeed or hang the machine. The event log is not helpful, as log messages end at the time of the hang, with no record of a warning or error. My only recourse when the machine hangs in this way is to perform a hard reset/power cycle. Any tips on how to further debug this issue are greatly appreciated.

    Read the article

  • Server 2008 RAID 5 Write Speeds

    - by Solipsism
    I recently configured a RAID 5 partition in Server 2008 with 4 RAID 5 disks. These disks are connected through a SATA expansion card that uses PCIe. This morning, I checked and they had finally finished synchronizing, and so I tried to do some speed tests. Copying off the disks started pretty much fine - speeds began at 125MB/s, then trailed down to about 70MB/s, which I found odd but not worrying. Writing TO the disks however is a completely different story. I attempted to copy some of my VM host ISOs onto the disks (~2-4 GB apiece) and this resulted in speeds of approximately 10MB/s. I tried copying both from a local disk (connected directly to the motherboard) and from another server ththe gigabit network and results were the same. I checked the performance monitor while transferring the files and the only thing that stuck out was that my memory hard faults shot up to 6,000 per minute (spiking around 200/s) by explorer.exe. The system is running 2GB of DDR667 ECC RAM and a quad-core 2.3GHz opteron. Is there anything I can do to fix this performance issue (buy more RAM? move the drives to a faster box?, etc) or am I just screwed so long as I stick to windows.

    Read the article

  • How do I determine if my server is AMT capable for remotely turning on or rebooting a frozen computer

    - by RDK45
    I just finished reading the subject post (http://superuser.com/questions/319859/remotely-turning-on-or-rebooting-a-frozen-computer) and have further questions. I very interested in remote access to my server, in particular restarting it when it is in a stalled or blue-screen state.. How can I determine if my server is AMT enabled? It has a GIGABYTE GA-Z68MA-D2H-B3 Motherboard and Intel Core i5-2500K CPU. Thanks....RDK45

    Read the article

  • Load is 0, yet site crawls (sometimes). What gives?

    - by Yegor
    I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

    Read the article

  • VMWare vSphere 5: 4 pNICs for iSCSI vs. 2 pNICs

    - by gravyface
    New SAN for me, never used before: it's an IBM DS3512, dual controller with a quad 1GbE NIC per controller that a client bought and needs help setting up. Hosts (x2) have 8 pNICs and while I usually reserve 2 pNICs for iSCSI per host (and 2 for VM, 2 for management, 2 for vMotion, staggered across adapters), these extra ports on the SAN have me wondering if storage I/O would be significantly improved with 2 additional NICs per host, or if the limitations of the vmkernel/initiator would prevent the additional multipaths from ever being realized. I'm not seeing alot of 4 pNIC iSCSI implementations per host; 2 is the de facto standard from what I've read/seen online. I could and probably will do some I/O testing, but just wondering if there's a "wall" that someone else has discovered long ago (i.e. before 10GbE) that makes a 4 NIC iSCSI per host setup somewhat pointless. Just to clarify: I'm not looking for a how-to, but an explanation (link to paper, VMWare recommendation, benchmark, etc.) as to why 2-NIC configurations are the norm vs. 4-NIC iSCSI configurations. i.e. storage vendor limitations, VMKernel/initiator limitations, etc.

    Read the article

  • Network throughput issue (ARP-related)

    - by Joel Coel
    The small college where I work is having some very strange network issues. I'm looking for any advice or ideas here. We were fine over the summer, but the trouble began few days after students returned to campus in force for the fall term. Symptoms The main symptom is that internet access will work, but it's very slow... often to the point of timeouts. As an example, a typical result from Speedtest.net will return .4Mbps download, but allow 3 to 8 Mbps upload speed. Lesser symptoms may include severely limited performance transferring data to and from our file server, or even in some cases the inability to log in to the computer (cannot reach the domain controller). The issue crosses multiple vlans, and has effected devices on nearly every vlan we operate. The issue does not impact all machines on the network. An unaffected machine will typically see at least 11Mbps download from speedtest.net, and perhaps much more depending on larger campus traffic patterns at the time. There is one variation on the larger issue. We have one vlan where users were unable to log into nearly all of the machines at all. IT staff would log in using a local administrator account (or in some cases cached credentials), and from there a release/renew or pinging the gateway would allow the machine to work... for a while. Complicating this issue is that this vlan covers our computer labs, which use software called Deep Freeze to completely reset the hard drives after a reboot. It could just the same issue manifesting differently because of stale data on machines that have not permanently altered low-level info for weeks. We were able to solve this, however, by creating a new vlan and moving the labs over to the new vlan wholesale. Instigations Eventually we noticed that the effected machines all had recent dhcp leases. We can predict when a machine will become "slow" by watching when a dhcp lease comes up for renewal. We played with setting the lease time very short for a test vlan, but all that did was remove our ability to predict when the machine would become slow. Machines with static IPs have pretty much always worked normally. Manually releasing/renewing an address will never cause a machine to become slow. In fact, in some cases this process has fixed a machine in that state. Most of the time, though, it doesn't help. We also noticed that mobile machines like laptops are likely to become slow when they cross to new vlans. Wireless on campus is divided up into "zones", where each zone maps to a small set of buildings. Moving to a new building can place you in a zone, thereby causing you to get a new address. A machine resuming from sleep mode is also very likely to be slow. Mitigations Sometimes, but not always, clearing the arp cache on an effected machine will allow it to work normally again. As already mentioned, releasing/renewing a local machine's IP address can fix that machine, but it's not guaranteed. Pinging the default gateway can also sometimes help with a slow machine. What seems to help most to mitigate the issue is clearing the arp cache on our core layer-3 switch. This switch is used for our dhcp system as the default gateway on all vlans, and it handles inter-vlan routing. The model is a 3Com 4900SX. To try to mitigate the issue, we have the cache timeout set on the switch all the way down to the lowest possible time, but it hasn't helped. I also put together a script that runs every few minutes to automatically connect to the switch and reset the cache. Unfortunately, this does not always work, and can even cause some machines to end up in the slow state for a short time (though these seem to correct themselves after a few minutes). We currently have a scheduled job that runs every 10 minutes to force the core switch to clear it's ARP cache, but this is far from perfect or desirable. Reproduction We now have a test machine that we can force into the slow state at will. It is connected to a switch with ports set up for each of our vlans. We make the machine slow by connecting to different vlans, and after a new connection or two it will be slow. It's also worth noting in this section that this has happened before at the start of prior terms, but in the past the problem has gone away on it's own after a few days. It solved itself before we had a chance to do much diagnostic work... hence why we've allowed it to drag so long into the term this time 'round; the expectation was this would be a short-lived situation. Other Factors It's worth mentioning that we have had about half a dozen switches just outright fail over the last year. These are mainly 2003/2004-era 3Coms (mostly 4200's) that were all put in at about the same time. They should still be covered under warranty, buy HP has made getting service somewhat difficult. Mostly in power supplies that have failed, but in a couple cases we have used a power supply from a switch with a failed mainboard to bring a switch with a failed power supply back to life. We do have UPS devices on all but three of four switches now, but that was not the case when I started two and a half years ago. Severe budget constraints (we were on the Dept. of Ed's financially challenged institutions list a couple years back) have forced me to look to the likes of Netgear and TrendNet for replacements, but so far these low-end models seem to be holding their own. It's also worth mentioning that the big change on our network this summer was migrating from a single cross-campus wireless SSID to the zoned approach mentioned earlier. I don't think this is the source of the issue, as like I've said: we've seen this before. However, it's possible this is exacerbating the issue, and may be much of the reason it's been so hard to isolate. Diagnosis At first it seemed clear to us, given the timing and persistent nature of the problem, that the source of the issue was an infected (or malicious) student machine doing ARP cache poisoning. However, repeated attempts to isolate the source have failed. Those attempts include numerous wireshark packet traces, and even taking entire buildings offline for brief periods. We have not been able even to find a smoking gun bad ARP entry. My current best guess is an overloaded or failing core switch, but I'm not sure on how to test for this, and the cost of replacing it blindly is steep. Again, any ideas appreciated.

    Read the article

  • Upgrading laptop processor

    - by user344996
    Hi. I have a Dell Studio 17. It's a few years old, and I wanted to upgrade the processor. It currently has an Intel Core 2 Duo T5750 @ 2.00GHz My question is how can I find out which processors are compatible?

    Read the article

  • Sun Fire V20z also with AMD Opteron 256?

    - by Dan
    Hi, I have a SUN Fire V20z with two Opteron 244, which I'd like to upgrade. The official datasheet says that it supports up to Opteron 252. I was wondering if it would also work with AMD Opteron 256, cause they have the same core voltage and socket? Thanks for helping.

    Read the article

  • Strange boot problems on 6 month old setup

    - by Balefire
    I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

    Read the article

  • Multicore system. How are the cores "sorted"

    - by asdrubael
    If I have a system with let's say two Quadcore CPUs and HyperThreading enabled, how do I know how the phsyical and virtual cores are sorted? For example if I force a process to run on "CPU 0" how to know which Core this really is? I remember a complex drawing about this, but didn't find anything useful.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >