Search Results

Search found 5963 results on 239 pages for 'rest wing'.

Page 169/239 | < Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >

• Route web traffic through a separate iterface

  - by tkane

  I'd like to route web traffic through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Routing WIFI and LAN for specific traffic

  - by jakebird451

  I have two network devices aboard my macbook pro: WIFI (en1): Used for general traffic. Connects to an ip of 192.168.19.* via DHCP LAN (en0): Used for specific traffic. Connects to an ip of 192.168.2.10 as a static IP. Does not connect to a router, only a switch for direct routing connection. I have 4 IP addresses I need to access on the LAN: 192.168.2.1 192.168.2.21 192.168.2.20 192.168.2.30 The rest of the traffic needs to go to WIFI. I have tried setting up a routing table for the specific ip addresses, but I only managed to mess up my network. I do not venture out into the world of networking too often, but this was the latest command I have been trying: sudo route add -host 192.168.2.30 -interface en0 This command killed my ability to use ping. It told me that ping could not allocate memory (is that even possible)? It also killed my wifi access. Logging out and back in fixed the issue. I really do not mind to make this solution permanent, so I am fine with a temporary routing.

  Read the article

• Is it a good Idea to switch to a SSD to use less battery?

  - by Walter Maier-Murdnelch

  I am thinking of buying a SSD for my laptop, mainly for the purpose of extended operating time when running on battery. At the moment I use a Hitachi HTS545032B9A300 (320GB) (Datasheet) as main drive and a Seagate Momentus 5400.3 120GB as secondary drive. I dualboot Windows and Linux but I don't need the windows partition any longer, a 120GB SDD would be more than sufficient space-wise. Speed is not an issue for me, I make heavy use of tmpfs (ramdrive) within Linux and transfers of bigger files are mainly through some network filesystem anyways, thus a cheaper SSD should do. For the purpose of comparison I chose the OCZ Vertex Plus 120GB. Power consumption always is a big promotional thing the industry uses to make me want to buy their SSDs, some sheet on the OCZ page provides an astonishing comparison of desktop HDDS and SSDs. The numbers I got comparing my laptop HDD and their SSD were not really astonishing any longer. Hitachi 320GB HDD: Startup (W, peak, max.) 4.5 Seek (W, avg.) 1.7 Read / Write (W, avg.) 1.4 Performance idle (W, avg.) 1.3 Active idle (W, avg.) 0.8 Low power idle (W, avg.) 0.5 Standby (W, avg.) 0.2 Sleep 0.1 OCZ 120GB SSD: 1.5W active 0.3W standby I see that there are differences, but actually they don't seem that high as I though they were. And compared to the power consuption of the rest of my system I wonder if it makes a difference at all. Have I just taken the wrong look at the whole thing or may I be better off to buy another battery for my laptop?

  Read the article

• Moving a lot of small files between servers using rsync

  - by Adirael

  Hello guys, I'm moving a lot of files (about 2 millions) between two servers on different locations using rsync over ssh, it seems to work fine but I just realised I'm losing some files on the process. I got server 1, with the original data, and server 2, with the copy. Server 1 runs CentOS 5 and Server 2 runs on Ubuntu 10. I'm doing the transfer on the Server's 2 command line like this: rsync -e ssh -avzn usr@server1:/remote/path /local/path The first file movement I did using tar, but I didn't though of piping it through ssh and it failed cause the disk on server 1 was almost full, so I transfered it anyways (it was about 200GB) and got about 80% of the files. Then I piped another tar with the rest of the files (they're in folders, I got 100 folders with about 30 subfolders each, with files inside) and now I got everything on server 2. I wanted to be sure, so I my two options are getting the md5sum of all the files and check them or running an rsync on server 2 against server 1, that's what I did. It got some missing stuff and now it says there's nothing more to do (DRY RUN). But I got at least two files that are missing inside a subfolder. I ran that same rsync on that folder, but still dry run. Am I doing something wrong? Thanks, and sorry for the wall of text.

  Read the article

• FTP Server upload and filesystem questions

  - by Alex

  I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

  Read the article

• What does this error mean in my IIS7 Failed Request Tracing report?

  - by Pure.Krome

  when I attempt to goto any page in my web application (i'm migrating the code from an asp.net web site to web application, and now testing it) .. i keep getting some not authenticated error(s) . So, i've turned on FREB and this is what it says... I'm not sure what that means? Secondly, i've also made sure that my site (or at least the default document which has been setup to be default.aspx) has anonymous on and the rest off. Proof: - C:\Windows\System32\inetsrv>appcmd list config "My Web App/default.aspx" -section:anonymousAuthentication <system.webServer> <security> <authentication> <anonymousAuthentication enabled="true" userName="IUSR" /> </authentication> </security> </system.webServer> C:\Windows\System32\inetsrv>appcmd list config "My Web App" -section:anonymousAuthentication <system.webServer> <security> <authentication> <anonymousAuthentication enabled="true" userName="IUSR" /> </authentication> </security> </system.webServer> Can someone please help?

  Read the article

• Error getting PAM / Linux integrated with Active Directory

  - by topper

  I'm trying to add a Linux server to a network which is controlled by AD. The aim is that users of the server will be able to authenticate against the AD domain. I have Kerberos working, but NSS / PAM are more problematic. I'm trying to debug with a simple command such as the following, please see the error. Can anyone assist me to debug? root@antonyg04:~# ldapsearch -H ldap://raadc04.corp.MUNGED.com/ -x -D "cn=MUNGED,ou=Users,dc=corp,dc=MUNGED,dc=com" -W uid=MUNGED Enter LDAP Password: ldap_bind: Invalid credentials (49) additional info: 80090308: LdapErr: DSID-0C090334, comment: AcceptSecurityContext error, data 525, vece I have had to munge some details, but I can tell you that cn=MUNGED is my username for logging into the AD domain, and the password that I typed was the password for said domain. I don't know why it says "Invalid credentials", and the rest of the error is so cryptic, I have no idea. Is my approach somehow flawed? Is my DN obviously wrong? How can I confirm the correct DN? There was a tool online but I can't find it. NB I have no access to the AD Server for administration or configuration.

  Read the article

• nginx virtual hosts are not working, all vhosts goes to the default one

  - by Adirael

  Hello, I just did a clean install of nginx + php-fpm on a VPS running Ubuntu 10.10, nginx is serving and PHP is working fine, but I'm not able to add vhosts to it. Well, I can add them, but only one works, the rest go to this first one. This is my first vhost, for host1: server { listen 80; server_name host1; access_log /var/log/nginx/host1.log; error_log /var/log/nginx/host1.error.log; location / { root /var/www/vhosts/host1/; index index.html index.htm index.php; } location ~ \.php$ { include /etc/nginx/fastcgi_params; #fastcgi_pass 127.0.0.1:9000; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_param SCRIPT_FILENAME /var/www/vhosts/host1/$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; } } And the second one, for host2: server { listen 80; server_name host2; access_log /var/log/nginx/host2.log; error_log /var/log/nginx/host2.error.log; location / { root /var/www/vhosts/host2/; index index.html index.htm index.php; } location ~ \.php$ { include /etc/nginx/fastcgi_params; #fastcgi_pass 127.0.0.1:9000; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_param SCRIPT_FILENAME /var/www/vhosts/host2/$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; } } The problem is, when I go to http://host1 everything is fine, but on http://host2, it just shows host1! I don't have Apache installed and everything comes from repos. Any pointers?

  Read the article

• Cannot ssh into server

  - by revolver

  I am trying to SSH into a linux machine running ubuntu, but the interactive shell stuck somewhere and I can't key in anything. I am on Mac OS X Lion. This only happens when I am trying to access via an external IP. Local LAN SSH is working perfectly. macbook:~ user$ ssh -v -v user@serverip // i skipped the rest of the log, but I can paste it here again if needed. Authenticated to serverip debug1: channel 0: new [client-session] debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug2: callback start debug2: client_session2_setup: id 0 debug2: channel 0: request pty-req confirm 1 debug1: Sending environment. debug1: Sending env LC_CTYPE = UTF-8 debug2: channel 0: request env confirm 0 debug2: channel 0: request shell confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 My terminal shell just hang after this, and I can't key in anything. I checked var/log/auth on the server and saw that the a session is being created and I had already logged in, but I don't see any responses on my client machine. I googled around and a lot of the solution had to do with the Broadcom wireless driver, but I am not even using one, so I am pretty clueless here. To give you more information, the linux machine is also running a web server, and I have no problem accessing the web server. Thanks. Any help is appreciated.

  Read the article

• Forward all traffic from one IP to another Ip on OS X

  - by Josh

  This is related to this question I just asked... I have two IP address on my iMac I want to "bridge". I'm not sure what the proper terminology is... here's the situation. My iMac has a firewire connection to my laptop and an ethernet connection to the rest of my office. My laptop has an ip of 192.168.100.2 (on the firewire interface). My iMac has an IP of 192.168.100.1 on the firewire interface, and two IPs, 10.1.0.6 and 10.1.0.7, on it's ethernet interface. If I wanted to forward all traffic coming in from 192.168.100.2 on my OS X machine to go out on IP 10.1.0.7, and vice-versa, can this be done? I assume I would use the ipfw command. Essentially I want to "bridge" the firewire network to the ethernet network so my laptop can see all the machines on the 10.1 network, and all those machines can see my laptop at 10.1.0.7. Is this possible?

  Read the article

• Route web browsing through a separate iterface

  - by tkane

  I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Disable touch pad for mouse button region on new HP pavillion models?

  - by John

  i bought a new hp pavillion dv6 series laptop. the laptop itself is fine but it has the new hp touchpad mouse which i absolutely hate. its such a stupid problem to have with a computer. the left and right mouse buttons are, themselves, part of of the touchpad, meaning that if i tap the buttons without actually pressing them down, it registers the same way as the mouse pad (the cursor moves, tap to click activates, etc.) this is a major annoyance because it prevents you from operating the mouse pad with anything more than a single finger; if for example i use my right hand index finger to move the cursor using the touch pad and rest my left hand index finger on the left mouse button for more efficient mouse-ing, the mouse will react as if im trying to use 2 fingers to move it and it will either just sit there or will spaz out. the only way this works is if i keep the finger that is resting on the mouse button absolutely still, which is very difficult and, therefore, very annoying. also, even if i do abide by the arbitrary new decree of single-finger mousepad operation, i still have a problem because when i press down on the left or right click buttons, the mouse moves slightly, what with the buttons also being part of the touch pad and all. this would not be that hard to avoid except that they decided to also make the buttons much harder to press down. now whenever i go to click something, i press hard on the mouse button, causing my finger to slightly move or roll or flatten out a bit, causing the cursor to move slightly, and causing me to click on something different. what i would like to know is if there is anyway that i can disable the touch pad on the buttons. i have gone through all of the settings under the synaptics menus but i cannot find anything about this. did i miss something in one of the menus? if not, then are there any updated drivers that allow for toggling of this function?

  Read the article

• Outlook 2010 Crashing Unpredictably

  - by cbkadel

  Very often when I open up Outlook 2010 and start doing actions in it, it will hang and become non responsive. I have tried letting it finish, but it never does come back (up to 20 minutes of letting it try). I generally have to restart Outlook and try again. Usually after about an hour of doing this, Outlook somehow snaps out of it and works for the rest of the day. It's generally in the morning (though I doubt that's the key variable). Generally, the emails that cause problems are HTML/formatted, but not always. What I've done so far to troubleshoot: Install Latest Outlook Hotfix (I think Dec 14, 2010) Start Outlook in Safe Mode Neither of those steps seem to make a difference. Usually - after about 10-15 restarts of Outlook on any given day, then it starts working thereafter. My next step is to uninstall/reinstall Office 2010, but I'm hoping someone has seen this and knows what to do about it - though not sure. My configuration is like this: Microsoft Online Services (using Microsoft's Sign In App) - Connecting to Exchange I have two other Exchange accounts in this profile (new feature in 2010) connected through Outlook Anywhere. Life Meeting Conferencing Add In I've disabled the People tab/add in. I've disabled the "Send to Bluetooth" add-in. Not sure what else to do. Thanks in advance.

  Read the article

• Setting up a home network

  - by Mat Richardson

  I'm trying to get my head around how to do this with the equipment I have. Here's how it is.. I have an old laptop that has server 2003 installed on it. This has no wireless NIC, but I have a spare wireless router that I can wire to it. We have a virgin wireless router which provides the home with internet access. What I would like to do it make resources on the server 2003 machine available to the rest of the devices in the home - specifically a couple of laptops running windows 7. Ideally I'd like to be able to use the laptop as a fileserver but maybe also offer application virtualization. In the first instance however, I'd like to create a file server with the laptop and allow connections to it by the other machines. Virtualisation is just a 'nice to have'... Given the hardware I have is this possible? Can you point me in the right direction how to do what I want if this is the case?

  Read the article

• Triple-Boot + 4 partition Limit

  - by dsimcha

  I just bought a new hard drive so that I could convert my XP-only machine into an XP-Ubuntu-Windows 7 triple boot machine. Since the drive is absurdly huge (1 TB) I wouldn't mind throwing ReactOS into the mix, too. I just found out that master boot records are limited to 4 entries, meaning 4 primary partitions. I had Windows XP set up on my old drive as a boot partition, a program files partition and a media partition. Since I really didn't want to install XP from scratch, I cloned this setup on my new drive. This leaves me one MBR partition entry for installing Windows 7, Ubuntu and ReactOS. I'd like to avoid having to install XP from scratch like the plague, partly because it's supposed to be a safety net in case things go wrong with my other OS's and because I've invested a lot of time getting it set up exactly the way I like it. Here are the options I've considered and why I don't like them: Install Windows 7 on my media partition. This would work, but I prefer to keep my media partition completely separate from any OS, so that I can reformat an OS partition without affecting my media partition at all. Use wubi or something to install Ubuntu in the same partition as something else. Again, this is brittle. Move all my media to a logical drive on an extended partition. Create another logical drive on this extended partition for Ubuntu. The problem here is that extended partitions are rather brittle--if you nuke one, it renders the rest useless. Just put the old drive back in my computer and run XP off it. Use the new one for the other OS's. The problem here is that the old drive is slower and uses extra power, generates extra heat, etc. Can anyone suggest any other possibilities that I may have overlooked?

  Read the article

• Server 2008R2 Server Manager Roles and Features won't refresh or allow addition of new roles or features

  - by MattChorba

  I have a standalone DC in an isolated lab. I have installed the SUR tool and found no errors. I ran SFC and found no errors. I have attempted to install Windows Backup feature using Powershell, but received the same error about the computer needing to be restarted. Powershell cmdlets will list all of the installed roles and features. The rest of Server Manager works without problems. What can I do to get Server Manager Roles and Features working properly again? Picture of Error: CheckSUR.log: ================================= Checking System Update Readiness. Binary Version 6.1.7601.21645 Package Version 13.0 2011-11-28 13:20 Checking Windows Servicing Packages Checking Package Manifests and Catalogs Checking Package Watchlist Checking Component Watchlist Checking Packages Checking Component Store Summary: Seconds executed: 413 No errors detected (w) Unable to get system disk properties 0x0000045D IOCTL_STORAGE_QUERY_PROPERTY Disk Cache CheckSUR.persist.log: ================================= Checking System Update Readiness. Binary Version 6.1.7601.21645 Package Version 13.0 2011-11-28 13:20 Checking Windows Servicing Packages Checking Package Manifests and Catalogs Checking Package Watchlist Checking Component Watchlist Checking Packages Checking Component Store Summary: Seconds executed: 413 No errors detected (w) Unable to get system disk properties 0x0000045D IOCTL_STORAGE_QUERY_PROPERTY Disk Cache

  Read the article

• What should I encrypt in Debian during install?

  - by ianfuture

  I have seen various guides and recommendations on web about how best to do this but nothing that clearly explains the best way and why. So I understand there is a need for part of Debian during install to be un-encrypted on its own partition to allow it to boot. Most info I have seen is call this /boot and set the boot flag. Next I believe the best approach is to create another partition out of all the rest of the disk space, encrypt this, then on top of that create a LVM and then within the LVM create my various partitions , name them , select size, and file system type. Can I include /swap in the encrypted LVM part ? Is this approach sound? If so what are the partitions I should use (this is going to be a minimal server install with a view to install as and when what I need for a dev server)? Finally how does the installer know what to put in each partition I define ? I appreciate there are more than one question but any help and suggestions would be appreciated. If further clarification is needed please mention in the comments . EDIT : 16/3/2010 After Richard Holloways reply I thought it relevant to add this info: The reasons why I want to do this are to explore maximising security on any server install and set up, due to interest in the area of Computer Security and Forensics. Also I am trying to peform the task as if it being performed in an enterprise situation. On a technical matter, once set up and configured with minimal packages and ssh this server will not physically be easy to access so I will only be entering via ssh. (Yes I know why encrypt something no one will ever be able to get their hands on? Because I can and I want to is the simple answer, but see above too).

  Read the article

• Possible for linux bridge to intercept traffic?

  - by A G

  I have a linux machine setup as a bridge between a client and a server; brctl addbr0 brctl addif br0 eth1 brctl addif br0 eth2 ifconfig eth1 0.0.0.0 ifconfig eth2 0.0.0.0 ip link set br0 up I also have an application listening on port 8080 of this machine. Is it possible to have traffic destined for port 80 to be passed to my application? I have done some research and it looks like it could be done using ebtables and iptables. Here is the rest of my setup: //set the ebtables to pass this traffic up to ip for processing; DROP on the broute table should do this ebtables -t broute -A BROUTING -p ipv4 --ip-proto tcp --ip-dport 80 -j redirect --redirect-target DROP //set iptables to forward this traffic to my app listening on port 8080 iptables -t mangle -A PREROUTING -p tcp --dport 80 -j TPROXY --on-port 8080 --tproxy-mark 1/1 iptables -t mangle -A PREROUTING -p tcp -j MARK --set-mark 1/1 //once the flows are marked, have them delivered locally via loopback interface ip rule add fwmark 1/1 table 1 ip route add local 0.0.0.0/0 dev lo table 1 //enable ip packet forwarding echo 1 > /proc/sys/net/ipv4/ip_forward However nothing is coming into my application. Am I missing anything? My understanding is that the target DROP on the broute BROUTING chain will push it up to be processed by iptables. Secondly, are there any other alternatives I should investigate? Edit: IPtables gets it at nat PREROUTING, but it looks like it drops after that; the INPUT chain (in either mangle or filter) doesn't see the packet.

  Read the article

• Lost Windows 7 boot after EasyBCD with EFI

  - by drent

  I've got a Lenovo Y580 with a 64GB SSD and a 1TB HDD setup using GPT and setup to boot from (U?)EFI. I was trying to get my Linux Mint installation on the Windows boot manager using EasyBCD (I didn't realise EFI but it wiped my boot partition/loader and I cannot seem to get Windows back (and I still can't get a bootable Linux Mint). Using the System Recovery utility, Startup Repair can't "see" windows (it might be because I'm using a 7 Pro disk to recover Home Premium?). In command prompt, Bootrec tools don't do anything and bootsect can't run because it says that it's for BIOS only and I've booted with EFI. I can see the EFI data on the 200mb SSD partition using diskpart but I don't know how to add Windows back onto whatever bootloader I have/need. At the moment the only options I can see are: Do a fresh install of Windows and hope that the setup remains as fast as the default one (the SSD is some kind of cache for Windows but I can't quite see how it works given that the rest of the SSD is unpartitioned space). This seems like overkill given that Windows was working fine til EasyBCD deleted it. Try forcing BIOS mode and see if that somehow magically fixes things Try converting from GPT to MBR to try and use the bootrec/bootsect tools (and maybe back again) which seems like a really bad idea. Anyone have any ideas?

  Read the article

• Take a regular Windows 7 clone with clonezilla (device-to-image)

  - by Mario De Schaepmeester

  I am unexperienced with cloning software and I've decided to use Clonezilla as it seemed best as freeware. I chose device image and left most options standard. I chose expert mode anyway to see what I could configure, and decided to try the lzop algorithm instead of the default one for compression. The rest was left at default. When Clonezilla asked me which partitions to clone (I chose parts to image), I chose the C:\ drive but Windows 7 also creates a 100MB partition on setup for system files (the actual boot partition?). I copied that into the image as well. The reason I didn't choose disk to image is that I also have a data partition that needs to stay intact. Now I'm simply not sure that this is the way to go, should I ever need to restore my disk image. Will Clonezilla know what to do with both partitions and will Windows 7 work perfectly after restoring? Edit: apparantly a similar question has been asked before. The link to the first article in the answer is not relevant to me since it covers a device-to-device clone. It appears the windows installation disk can repair the 100MB partition. As for Clonezilla, it copies "hidden data after the MBR" by default too. I don't know, I feel I'll be allright whether by restoring the partition with Clonezilla or repairing it with the Windows 7 disk.

  Read the article

• How do you update without cutting off users?

  - by Griffin

  I searched around and I was surprised that I couldn't find an answer to this question. My assumption is that you have multiple servers. Normally they both will be doing their specific take (for the rest of this I will assume a simple website). Now lets say server A & B need updates. Do you update server A while server B keeps pushing out the webpage and then when server A is okay you update server B? This seems like it would work in small scale but seems horrible in large scale due to the fact that you'd need twice the power that you normally have. When dealing with a large number of servers do you update small sections at a time? I thought the problem with this would be if server A can't work alongside server B C D E or F any-longer that's not that bad. But when you start updating you slowly lose this small percentage. What is the proper way to deal with updates like this?

  Read the article

• Terminal Server CPU usage at 100%

  - by Light1c3

  I'm running a terminal server with around 50-60 users,and every so often the server will go from 40% usage to 100%. I took a closer look an it seems every time this happens, a different user or two seem to be caught in a loop and end up using < 30% where the rest of the users only use a maximum of 5%. The company behind the software we use clame it's due to the servers inadequate hardware (It's a VM system running on a dual - quad core setup) which to me sounds like BS! I'm fairly new to this level of IT so if I misspoke I apologize. I have no way to prove it but I believe adding more raw hardware power wont do me any good as this to me seems like a bug in their software, and it will suck up as much ( or little) CPU as it's given. The VM in question has 4 vCPU cores and 12 GB RAM available, and is running Windows Server 2008, 64-bit Thanks in advance for your help! Note: I have the same question posted on SO, but was pointed in this direction so just in case, here is a link to the post http://stackoverflow.com/questions/17276602/termserver-cpu-at-100

  Read the article

• Ubuntu 12.04 can't boot after installing with software RAID 1

  - by Bill

  I've been trying to install Ubuntu with software RAID on my server and there is obviously something that I don't understand about the process. This is the guide that I followed: https://help.ubuntu.com/11.04/serverguide/advanced-installation.html I have two identical 1 TB disks in my server. I went through the initial install process and manually set up my partitions. On each disk I set up: (1) 100 MB partition for EFI boot (I didn't originally have this but added it based on a forum post I found after my original install failed to boot, I ended up with EFIboot since that was what the 'guided partitioning' decided to do) (1) 970 MB partition for / (1) 30 MB partition for swap I then created new RAID 1 disks combining the two partitions, one from each disk, such that each partition is mirrored. I then configured their usage as stated above. After saving the configuration I said yes to boot in a degraded state. The rest of the setup went normally, no errors of any kind. I saw GRUB being installed and again no errors. However, after rebooting the server I get the dreaded 'Insert boot media' and nothing happens. I loaded up the recovery disk and the mdadm configuration looks correct. md0 is my EFIBoot partition md1 is my \ partition using ext4 md2 is my swap partition Running file -s /dev/md0 doesn't indicate that GRUB is there and so I attempted to reinstall GRUB using the recovery disk. I selected the md0 disk and it appeared to install just fine. Running file -s /dev/md1 shows the error needs journal recovery, I'm not sure if that's related or not or how to fix that. Rebooting gives me the same problem, no boot media found. I've searched around the internet but can't figure out what to do next or more importantly how to troubleshoot what exactly is going wrong. Thanks!

  Read the article

• Upgrade Centos 5 tot PHP 5.2 or 5.3 [recommended way?]

  - by solid

  We are using Zend Framework and in version 2, php 5.2 will be the minimum requirement. We love CentOS and we'd like to keep using it, but PHP 5.1 just won't do anymore when developing web applications with Zend framework. I found several links to solutions to upgrade with external repositories. http://serverfault.com/questions/106801/recommended-method-to-upgrade-php-5-1-6-to-5-2-x-on-centos-5 http://www.webtatic.com/blog/2009/05/installing-php-526-on-centos-5/ http://www.webtatic.com/blog/2009/06/php-530-on-centos-5/ We'd like to see another solution with the use of an "official?" CentOS repository if any is available. We only need to upgrade PHP, the rest of the CentOS setup is fine the way it is. For us, it's important however to keep the YUM cycle intact using the normal repositories. So in short: is it even possible to upgrade only PHP by using an external repo or otherwise? While still upgrading all our other packages safely through normal yum usage? Thanks for your help!

  Read the article

• Batch-Remove Specific Text from Photo Descriptions

  - by David

  I've recently upgraded to iPhoto '11 (couldn't resist the pricing on the new app store) and as I'm adding more meta-data to my library and generally organizing things (places, faces, etc... I hadn't upgraded since '08) I've noticed something odd in my photos. Every photo in my library has a description (though many are short), but it would appear that somehow the description of one of the photos has been appended to many. I don't know if maybe I accidentally screwed up a batch change at some point in the past, or if the library upgrade somehow messed up, or what else may have happened. But what I need to do is fix these somehow. Now, manually editing is something of a daunting task. Within a library of 21,248 photos, 18,858 of them have this additional text. The one thing I do have going for me is that it's a specific string. If there's a way to "remove this string from everywhere in the library without removing the rest of any given description" then that would be perfect. Is there anything I can do like this? Maybe even manually editing a library file in a text editor? (Would that break anything else in iPhoto if its library was edited outside of the application, even while it's not running?) Does anybody have any ideas?

  Read the article

< Previous Page | 165 166 167 168 169 170 171 172 173 174 175 176  | Next Page >