Search Results

Search found 171496 results on 6860 pages for 'not joe bloggs'.

Page 170/6860 | < Previous Page | 166 167 168 169 170 171 172 173 174 175 176 177  | Next Page >

  • Storage device not found on ESX4 with AIC-9410

    - by Mads
    I am trying to install ESX 4.0 update 1 on a Supermicro X7DBR-3 system with an embedded AIC-9410 HBA (this HBA is listed on the HCG with Vendor ID 9005 and Device ID 041f) . All SATA controllers are disabled in the BIOS and the logical drive shows up in the Adaptec device summary during POST, however there is nothing listed on the Storage Device screen. The HBA itself is listed if I run esxcfg-info but not if I run esxcfg-scsidevs -a (under ESXi for that last command) Any ideas where I can look next or what might be wrong?

    Read the article

  • HISTCONTROL=ignoreboth not working Debian Lenny

    - by Mike
    Can anybody confirm if by setting the the following environmental variables under debian lenny will make previous history entries not to be saved. GNU bash, version 3.2.39(1)-release export HISTCONTROL=ignoreboth export HISTSIZE=500 I have added them to my /etc/bash.bashrc but I keep getting repeated commands. Thanks

    Read the article

  • Nginx + php5-fpm = "File not found"

    - by MatW
    I've hit a wall whilst setting up a site using nginx / fpm. The page displays "File not found", and this appears in the nginx error.log: FastCGI sent in stderr: "Primary script unknown" while reading response header from upstream I'm new to both nginx and fpm, and that error message means nothing to me (even the google machine hasn't helped!). Can anyone shed any light onto what could be happening?

    Read the article

  • Wireless Router will not allow connection

    - by Chris
    I am working with a RangeMax(TM) Wireless Router WPN824 v2, and it will not allow a wireless connection nor a wired connection. I am at an actual lost, with no way into the router I cannot test settings. I have unplugged it, left it off for a 32 hours, and reset it with no luck. Any ideas? Could the router just be done-zo?

    Read the article

  • Fresh XP Install: PS2 Keyboard not working

    - by RedLeader
    I reformatted a drive to NTFS (not quick) and installed Windows XP on it. Now it's trying to do the graphical portion of the setup, wanting me to click Accepts and Nexts... but I can't! The keyboard works to get to the BIOS and in the BIOS. I have reset the CMOS many times, tried fail-safe and optimized defaults, and even enabled USB Keyboard and mouse support (even though the I have no USB devices plugged in).

    Read the article

  • Centreon setup (web part) config not writeable

    - by Evgeniy
    I have a problem with Centreon installation. At end of install process, I stopped at 10th step: Writable Centreon Configuration File (centreon.conf.php) Critical: Not Writeable /etc/centreon/ asterisk:asterisk (755) Should be : (755) Generate Centreon configuration file OK /etc/centreon/centreon.conf.php asterisk:asterisk (755) Should be : (755) Generate Centstorage configuration file OK /etc/centreon//conf.pm asterisk:asterisk (755) Should be : (755) But permissions and owner are OK. And I tried chmod -R 777 /etc/centreon Please help to understand what's wrong. UPD: Screenshot: http://gyazo.com/82701d119a5e0d98947ad35406a5b8f3

    Read the article

  • Directory listing through FTPS (TLS) is not working

    - by Aron Rotteveel
    We recently switched our server to require TLS for every connection. This is working flawlessly so far, but one of our clients is having problems. Some facts: Server uses Pure-FTPD Server has a passive port range configured Server has no firewall limitations regarding the FTP Client uses WS FTP Client is behind a router Client connects to the same IP as every other, using PASSIVE mode All other clients have no trouble connecting Because of the TLS requirement, connecting using ACTIVE mode is almost not possible, but PASSIVE is working fine for everyone except this specific client. It seems that he is able to connect, but once a LIST command is performed, things go wrong. Log: Finding Host <clienthost> ... Connecting to <serverip:21> Connected to <serverip:21> in 0.020000 seconds, Waiting for Server Response Initializing SSL Session ... 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- 220-You are user number 5 of 50 allowed. 220-Local time is now 22:14. Server port: 21. 220-This is a private system - No anonymous login 220-IPv6 connections are also welcome on this server. 220 You will be disconnected after 15 minutes of inactivity. AUTH TLS 234 AUTH TLS OK. SSL session NOT set for reuse SSL Session Started. Host type (1): Automatic Detect USER <user> 331 User <user> OK. Password required PASS (hidden) 230-User <user> has group access to: <user> 230 OK. Current restricted directory is / SYST 215 UNIX Type: L8 Host type (2): Unix (Standard) PBSZ 0 200 PBSZ=0 PROT P 200 Data protection level set to "private" PWD 257 "/" is your current location CWD /public_html 250 OK. Current directory is /public_html PWD257 "/public_html" is your current location TYPE A 200 TYPE is now ASCII PASV 227 Entering Passive Mode (<serverip>,132,100) connecting data channel to <serverip>:132,100(33892) Substituting connection address <serverip> for private address <serverip> from PASV Using external address <customer ext. ip> instead of local address <customer int. ip> for PORT command PORT 82,161,56,225,195,181 200 PORT command successful LIST Error reading response from server. It appears that the connection is dead. Attempting reconnect... Any help is appreciated.

    Read the article

  • dns does not work from different drive letters

    - by n1zero
    C:\>ping localhost Pinging Vextor [127.0.0.1] with 32 bytes of data: Reply from 127.0.0.1: bytes=32 time<1ms TTL=128 Reply from 127.0.0.1: bytes=32 time<1ms TTL=128 Ping statistics for 127.0.0.1: Packets: Sent = 2, Received = 2, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms Control-C ^C C:\>f: F:\>ping localhost Ping request could not find host localhost. Please check the name and try again.

    Read the article

  • Snort install issue on debian 6 with libpcre - libpcre library not found

    - by Chuck
    I've read the manual on snort.org for installing snort on Debian but am still having an issue. Does anyone know how to resolve this? I've tried installing the libpcre3 amd libpcre3-dev packages by using apt-get and also manually installing by downloading the latest version off the tcpdump website. Any ideas? Checking for pcre-compile in -l pcre...no Error! Libpcre library not found. Get it from http://www.pcre.org

    Read the article

  • Postfix SMTP auth not working with virtual mailboxes + SASL + Courier userdb

    - by Greg K
    So I've read a variety of tutorials and how-to's and I'm struggling to make sense of how to get SMTP auth working with virtual mailboxes in Postfix. I used this Ubuntu tutorial to get set up. I'm using Courier-IMAP and POP3 for reading mail which seems to be working without issue. However, the credentials used to read a mailbox are not working for SMTP. I can see from /var/log/auth.log that PAM is being used, does this require a UNIX user account to work? As I'm using virtual mailboxes to avoid creating user accounts. li305-246 saslauthd[22856]: DEBUG: auth_pam: pam_authenticate failed: Authentication failure li305-246 saslauthd[22856]: do_auth : auth failure: [user=fred] [service=smtp] [realm=] [mech=pam] [reason=PAM auth error] /var/log/mail.log li305-246 postfix/smtpd[27091]: setting up TLS connection from mail-pb0-f43.google.com[209.85.160.43] li305-246 postfix/smtpd[27091]: Anonymous TLS connection established from mail-pb0-f43.google.com[209.85.160.43]: TLSv1 with cipher ECDHE-RSA-RC4-SHA (128/128 bits) li305-246 postfix/smtpd[27091]: warning: SASL authentication failure: Password verification failed li305-246 postfix/smtpd[27091]: warning: mail-pb0-f43.google.com[209.85.160.43]: SASL PLAIN authentication failed: authentication failure I've created accounts in userdb as per this tutorial. Does Postfix also use authuserdb? What debug information is needed to help diagnose my issue? main.cf: # TLS parameters smtpd_tls_cert_file = /etc/ssl/certs/smtpd.crt smtpd_tls_key_file = /etc/ssl/private/smtpd.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # SMTP parameters smtpd_sasl_local_domain = smtpd_sasl_auth_enable = yes smtpd_sasl_security_options = noanonymous broken_sasl_auth_clients = yes smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination smtp_tls_security_level = may smtpd_tls_security_level = may smtpd_tls_auth_only = no smtp_tls_note_starttls_offer = yes smtpd_tls_CAfile = /etc/ssl/certs/cacert.pem smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom /etc/postfix/sasl/smtpd.conf pwcheck_method: saslauthd mech_list: plain login /etc/default/saslauthd START=yes PWDIR="/var/spool/postfix/var/run/saslauthd" PARAMS="-m ${PWDIR}" PIDFILE="${PWDIR}/saslauthd.pid" DESC="SASL Authentication Daemon" NAME="saslauthd" MECHANISMS="pam" MECH_OPTIONS="" THREADS=5 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd" /etc/courier/authdaemonrc authmodulelist="authuserdb" I've only modified one line in authdaemonrc and restarted the service as per this tutorial. I've added accounts to /etc/courier/userdb via userdb and userdbpw and run makeuserdb as per the tutorial. SOLVED Thanks to Jenny D for suggesting use of rimap to auth against localhost IMAP server (which reads userdb credentials). I updated /etc/default/saslauthd to start saslauthd correctly (this page was useful) MECHANISMS="rimap" MECH_OPTIONS="localhost" THREADS=0 OPTIONS="-c -m /var/spool/postfix/var/run/saslauthd -r" After doing this I got the following error in /var/log/auth.log: li305-246 saslauthd[28093]: auth_rimap: unexpected response to auth request: * BYE [ALERT] Fatal error: Account's mailbox directory is not owned by the correct uid or gid: li305-246 saslauthd[28093]: do_auth : auth failure: [user=fred] [service=smtp] [realm=] [mech=rimap] [reason=[ALERT] Unexpected response from remote authentication server] This blog post detailed a solution by setting IMAP_MAILBOX_SANITY_CHECK=0 in /etc/courier/imapd. Then restart your courier and saslauthd daemons for config changes to take effect. sudo /etc/init.d/courier-imap restart sudo /etc/init.d/courier-authdaemon restart sudo /etc/init.d/saslauthd restart Watch /var/log/auth.log while trying to send email. Hopefully you're good!

    Read the article

  • radvd is not assigning prefix

    - by Samik
    I'm currently trying to setup IPv6 address auto-configuration with router advertisement daemon (radvd) on a virtual machine running CentOS 6.5. But the eth0 interface is not obtaining that prefix. I've obtained the ULA prefix from here. Contents of /etc/sysctl.conf # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 net.ipv6.conf.all.forwarding = 1 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 0 # Controls whether core dumps will append the PID to the core filename. # Useful for debugging multi-threaded applications. kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Disable netfilter on bridges. net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 # Controls the default maxmimum size of a mesage queue kernel.msgmnb = 65536 # Controls the maximum size of a message, in bytes kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 Contents of /etc/radvd.conf # NOTE: there is no such thing as a working "by-default" configuration file. # At least the prefix needs to be specified. Please consult the radvd.conf(5) # man page and/or /usr/share/doc/radvd-*/radvd.conf.example for help. # # interface eth0 { AdvSendAdvert on; MinRtrAdvInterval 3; MaxRtrAdvInterval 10; AdvDefaultPreference low; AdvHomeAgentFlag off; prefix fd8a:8d9d:808f:1::/64 { AdvOnLink on; AdvAutonomous on; AdvRouterAddr on; }; }; Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes I've also enabled radvd at startup through chkconfig. Though I noticed that radvd is starting after interfaces are brought up. I've tried restarting the network service afterwards but still I get the following link-local address only #ip -6 addr show 1: lo: mtu 16436 inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: mtu 1500 qlen 1000 inet6 fe80::5054:ff:fe74:d746/64 scope link valid_lft forever preferred_lft forever Edit: Based on the answer given by Sander Steffann I still need clarification on some points but I'm posting here what worked. Contents of /etc/sysconfig/network NETWORKING=yes HOSTNAME=syslog-ng-server NETWORKING_IPV6=yes IPV6FORWARDING=yes Contents of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 HWADDR=52:54:00:74:d7:46 TYPE=Ethernet UUID=af5db1cb-e809-4098-be1a-5a74dbb767b1 ONBOOT=yes NM_CONTROLLED=no BOOTPROTO=dhcp IPV6INIT=yes IPV6_AUTOCONF=yes IPV6FORWARDING=no Removed following line from /etc/sysctl.conf net.ipv6.conf.all.forwarding = 1 Contents of /etc/radvd.conf is as previous.

    Read the article

  • wvMaxima Error: "Not Connected To Maxima" on Windows

    - by muntoo
    Maxima gives an error "Not Connected To Maxima" whenever I try to do anything with it. I've looked around, but I couldn't figure out how to fix this on Windows. The only results I got were for Fedora. According to them, I think this may have something to do with the Firewall, but I can't figure out what. I even tried adding wvMaxima to the Windows Firewall exceptions list, but the same error comes up.

    Read the article

  • Windows 7: Menu 'New->Text document' is missing, when not admin user

    - by Isamux
    Hi, when I'm logged in as a user that is not member of the administrator group the entry to create a new textfile is missing from the right click "New" menu. If I give the user admin rights or start the explorer with admin rights the "New - text document" menu entry magically appears. As far as I can see the registry entries are correct. Anybody got a solution for that side effect of beeing a normal user in windows?? Regards

    Read the article

  • Group Policy: Not working after few days

    - by Kabir Rao
    Hi, I have implemented a group policy as per the suggestion http://serverfault.com/questions/121065/change-local-computer-policy-on-windows-2003-terminal-server . it worked fine when i tested..but after two days it is not working...can somebody help. Thanks, Kabir

    Read the article

  • Choose Default Program does not work (is broken) on Windows

    - by Piotr Dobrogost
    For some time now when I click Open with...|Choose Default Program from Windows Explorer's context menu I'm getting this error This file does not have a program associated with it to perform this action. Create an association in the Set Associations control panel. I'm getting this error no matter what the extension of the selected file is. Any ideas how to fix this?

    Read the article

  • SSL_CLIENT_CERT_CHAIN not being passed to backend server

    - by nidkil
    I have client certificate configured and working in Apache. I want to pass the PEM-encoded X.509 certificates of the client to the backend server. I tried with the SSLOptions +ExportCertData. This does nothing at all, while the documentation states it should add SSL_SERVER_CERT, SSL_CLIENT_CERT and SSL_CLIENT_CERT_CHAINn (with n = 0,1,2,..) as headers. Any ideas why this option is not working? I then tried setting the headers myself using RequestHeader. This works fine for all variables except SSL_CLIENT_CERT_CHAIN. It shows null in the header. Any ideas why the certificate chain is not being filled? This is my first Apache configuration: <VirtualHost 192.168.56.100:443> ServerName www.test.org ServerAdmin webmaster@localhost DocumentRoot /var/www ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/ssl_access.log combined SSLEngine on SSLProxyEngine on SSLCertificateFile /etc/apache2/ssl/certs/www.test.org.crt SSLCertificateKeyFile /etc/apache2/ssl/private/www.test.org.key SSLCACertificateFile /etc/apache2/ssl/ca/ca.crt <Proxy *> AddDefaultCharset Off Order deny,allow Allow from all </Proxy> <Location /carbon> ProxyPass http://www.test.org:9763/carbon ProxyPassReverse http://www.test.org:9763/carbon </Location> <Location /services/GbTestProxy> SSLVerifyClient require SSLVerifyDepth 5 SSLOptions +ExportCertData ProxyPass http://www.test.org:8888/services/GbTestProxy ProxyPassReverse http://www.test.org:8888/services/GbTestProxy </Location> </VirtualHost> This is my second Apache configuration: <VirtualHost 192.168.56.100:443> ServerName www.test.org ServerAdmin webmaster@localhost DocumentRoot /var/www ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/ssl_access.log combined SSLEngine on SSLProxyEngine on SSLCertificateFile /etc/apache2/ssl/certs/www.test.org.crt SSLCertificateKeyFile /etc/apache2/ssl/private/www.test.org.key SSLCACertificateFile /etc/apache2/ssl/ca/ca.crt <Proxy *> AddDefaultCharset Off Order deny,allow Allow from all </Proxy> <Location /carbon> ProxyPass http://www.test.org:9763/carbon ProxyPassReverse http://www.test.org:9763/carbon </Location> <Location /services/GbTestProxy> SSLVerifyClient require SSLVerifyDepth 5 RequestHeader set SSL_CLIENT_S_DN "%{SSL_CLIENT_S_DN}s" RequestHeader set SSL_CLIENT_I_DN "%{SSL_CLIENT_I_DN}s" RequestHeader set SSL_CLIENT_S_DN_CN "%{SSL_SERVER_S_DN_CN}s" RequestHeader set SSL_SERVER_S_DN_OU "%{SSL_SERVER_S_DN_OU}s" RequestHeader set SSL_CLIENT_CERT "%{SSL_CLIENT_CERT}s" RequestHeader set SSL_CLIENT_CERT_CHAIN0 "%{SSL_CLIENT_CERT_CHAIN0}s" RequestHeader set SSL_CLIENT_CERT_CHAIN1 "%{SSL_CLIENT_CERT_CHAIN1}s" RequestHeader set SSL_CLIENT_VERIFY "%{SSL_CLIENT_VERIFY}s" ProxyPass http://www.test.org:8888/services/GbTestProxy ProxyPassReverse http://www.test.org:8888/services/GbTestProxy </Location> </VirtualHost> Hope someone can help. Regards, nidkil

    Read the article

  • apache2: Could not reliably determine the server's fully qualified domain name

    - by Joseph Silvashy
    I've never encountered this error before. And secondly I'd like to know how you folks debug your apache configurations. apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName In my Virtual Host configuration I do have these lines: ServerName example.com ServerAlias www.example.com (of course it has my actual info in there) So I guess my question is, why wouldn’t apache be able to determine my fully qualified domain name?

    Read the article

  • DPM 2010 "Disk failed or disk not found"

    - by SysAdmin
    I have an HP Proliant ML110 G5 server with Windows server 2008R2 only dedicated for DPM 2010. This server has a limit in HD of 8TB which has already been met. I'm now stuck in this situation where my disk keeps failing "Disk failed or Disk not found" in the disk management. Only after I reboot the system the disk comes back up. Today I was running my monthly tape backup on a certain protection group and the disk failed again while the tape job was running (so the job wasn't completed). This is the description of the error in the alerts: "The disk Disk 1 - Hitachi HDS722020ALA330 SCSI Disk Device cannot be detected or has stopped responding. All subsequent protection activities that use this disk will fail until the disk is brought back online. (ID 3120)". My backup system is becoming useless! I don't think that is a hardware issue (please correct me if I'm wrong) since the HD works fine for a certain period of time which is becoming shorter and shorter. I basically have no more option to fix this problem. I tried to fix any error that was coming up in the event viewer with no luck (included one regarding the SQL2008 compatibility issue). The disk keeps failing! Now I'm only trying to recover/migrate the data from the disk that is having problem but my issue now is that I cannot add any drives to my server since I already got installed the maximum storage capacity 8TB. I thought about 2 simple options. Please tell me what you guys think about it; Unplug one of the 2 storage pool disks (disk0, that one without problem) from the machine and install a new one in order to migrate the data with the Migration tool for DPM. Remove the defective disk (disk1), put back the disk0 and run the synchronization/consistency check on all the groups to recreate replicas and recovery points. Run diskpart.exe and clean up the disk (loosing all data) and hoping that he will work after I sync all the protection groups. Both solutions are not elegant but I have no better options at the moment. Please I need some help. Thanks for your time Angelo

    Read the article

  • MySQL Table does not support optimize

    - by Dscoduc
    My Wordpress tables appear to be in need of optimization so I looked into the commmand OPTIMIZE TABLE . When I run the command I get the following results: Table does not support optimize, doing recreate + analyze instead The tables are built using the Wordpress 2.91 installer and haven't been modified at all. Is this normal? How can I optimize my database to keep things working correctly?

    Read the article

  • SCSI drives not showing up in Linux CentOS 4

    - by Mohammad
    So I have a poweredge 6650 with Perc 3 installed. on the first channel of raid controller I have 2x 73gb configured in raid 1. On the second channel I have two 300GB drives that are stand alone. The two 300gb drives do not show up in linux, (no /dev/sdb*)... Can perc 3 support non-raid and raid drives combined? Is there any settings I may be missing? Thanks in advance :)

    Read the article

  • OCZ Vertex 2 not recognized by Ubuntu installer

    - by Zsub
    As I boot into the Ubuntu 10.10 (or 11.04, doesn't matter) live environment or installer, it just refuses to recognise my Vertex 2. It reports the disk as ATA and not supporting smart, shows no serial number, and doesn't list the size correctly. All fdisk tells me is Unable to read /dev/sda (it's the only storage in the PC). I'm now running a temporary install of Windows 7 off of it, which worked like a charm, so where am I going wrong with Ubuntu... Specs: Asus M4N68T-M LE V2 (BIOS 0702, most recent) OCZ Vertex 2 SSD 60 GB Amd Athlon II X4 640 Patriot PSD34G13332 4GB DDR3 ram (two banks) EDIT I installed a second drive, installed Ubuntu on that and booted, it recognised the SSD just fine. I'm now trying to apt-get upgrade the live-environment. I wonder if there is any way to sort of install Ubuntu from Ubuntu (I boot into the working install on the other drive, install it on the SSD and then boot from the SSD). EDIT2 Ok, so that doesn't work. The install detects the SSD, however, it cannot format it. EDIT3 After a fresh boot I can read out SMART-data and even perform a read-benchmark, but if I try to format it, or do a write-bench, it'll crap out and after that it says SMART is not supported. So basically it seems I can't write to the disk, as it will stop working when I do, I will try to run repeated read-benchmarks to see if that has any effect. EDIT4 I'm running several read benchmarks on the drive right now, they give results that are to be expected from an SSD. If the read-benches don't fail, I can use fdisk on the disk, but it is now stuck trying to re-read the partition table after issueing the 'w' command. EDIT5 Parted Magic did recognize the drive and with hdparm -I even could tell me the drive was in a frozen state. I powercycled it (just pull out the plug from the SSD and plug it back in) and it wasn't frozen anymore. After that I could upgrade the firmware on the drive (still using Parted Magic) and format it to Ext4. After I rebooted into the Ubuntu installer, it wouldn't get recognized and hdparm didn't want to talk to it saying HDIO_DRIVE_CMD(identify) failed: Invalid exchange. EDIT6 For some reason if I enable one of the RAID controllers (the one the SSD is connected to, obviously) Ubuntu will let me format it, mount it and write to it. The installer also recognizes it. However if the raid controller is enabled but no array is defined the motherboard can't boot from it :(

    Read the article

  • Windows 7: Creating a password-protected task (NOT a programming question)

    - by Matthias
    Hello, I would like to configure a task like "child control software", so it would hibernate the pc at certain times. Is it possible to prevent modification (here: pausing) of a task through requiring the entering of the admin password to modify, EVEN THOUGH the currently-logged-in (and only) user is the admin account itself? (Do you know of any child control software that does NOT require an additional account yet is able to hibernate the system at certain times?) Thanks a lot! Matthias

    Read the article

< Previous Page | 166 167 168 169 170 171 172 173 174 175 176 177  | Next Page >