Search Results

Search found 5757 results on 231 pages for 'refresh policy'.

Page 170/231 | < Previous Page | 166 167 168 169 170 171 172 173 174 175 176 177  | Next Page >

• NetBackup prefers "Scratch" tapes over dedicated tapes

  - by wfaulk

  I have a NetBackup 6.0MP7 installation running on Windows Server 2003. It functions as the only Master Server and Media Server. I swap a full set of tapes in and out every week, but leave a set of tapes with their Volume Pool set to "Scratch" in all the time. The weekly tape sets then get rotated back in after a period of time. Largely, this works fine. I seldom actually need the scratch tapes, but every once in a while, a backup will run over what I have dedicated to the task. However, one week's set of tapes consistently gets declined in favor of the scratch pool. The backup policies are the same for every week, they all have "Policy Volume Pool" set to "NetBackup", and all of the tapes for every week (beside the scratch tapes) have had their pools assigned as "NetBackup", definitely including the week that always gets ignored. That said, it doesn't ignore all of the NetBackup pool tapes for that week. It does usually write to two or three of them, but it writes to like 20 of the scratch tapes. (I haven't thought to look to see if it's always the same two or three tapes.) And this problem never seems to occur for any other week. It doesn't load the tapes and then reject them; it never seems to try to use them at all. They are not flagged as frozen. They are all active and unassigned when I swap them in. The tapes are in a Quantum PX510 tape library. The NetBackup server is attached to the library/robot via fibrechannel going through an HP-branded Brocade switch. I'm not an expert on NetBackup at all. I don't really even know where to look. Any advice on logs to look at or logging to enable or really anything at all would be appreciated. I'll keep an eye on the question and update it if anyone needs any more info to help.

  Read the article

• Connect to Postgres remotely, open port 5432 for Postgres in iptables

  - by Victor

  I am trying to connect to Postgres remotely but I need to open port 5432 in iptables. My current iptables configuration is as follows: *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT What would I have to add in iptables to open the port? I'm trying to install phppgadmin on a different server to access the postgres database. Thank you.

  Read the article

• Allow access from outside network with dmz and iptables

  - by Ivan

  I'm having a problem with my home network. So my setup is like this: In my Router (using Ubuntu desktop v11.04), I installed squid proxy as my transparent proxy. So I would like to use dyndns to my home network so I could be access my server from the internet, and also I installed CCTV camera and I would like to enable watching it from internet. The problem is I cannot access it from outside the net. I already set DMZ in my modem to my router ip. My first guess is because i'm using iptables to redirect all inside network to use squid. And not allow from outside traffic to my inside network. Here is my iptables script: #!/bin/sh # squid server IP SQUID_SERVER="192.168.5.1" # Interface connected to Internet INTERNET="eth0" # Interface connected to LAN LAN_IN="eth1" # Squid port SQUID_PORT="3128" # Clean old firewall iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X # Load IPTABLES modules for NAT and IP conntrack support modprobe ip_conntrack modprobe ip_conntrack_ftp # For win xp ftp client #modprobe ip_nat_ftp echo 1 > /proc/sys/net/ipv4/ip_forward # Setting default filter policy iptables -P INPUT DROP iptables -P OUTPUT ACCEPT # Unlimited access to loop back iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT # Allow UDP, DNS and Passive FTP iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT # set this system as a router for Rest of LAN iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT # unlimited access to LAN iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT # DNAT port 80 request comming from LAN systems to squid 3128 ($SQUID_PORT) aka transparent proxy iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT # if it is same system iptables -t nat -A PREROUTING -i $INTERNET -p tcp --dport 80 -j REDIRECT --to-port $SQUID_PORT # DROP everything and Log it iptables -A INPUT -j LOG iptables -A INPUT -j DROP If you know where did I miss, please advice me. Thanks for all your help and I really appreciate it.

  Read the article

• Nexus functionality is limited after installation

  - by Dmitriy Sukharev

  I have a CentOS based server with Sonatype Nexus 2.0.4-1 installed. The issue is that there are no standard "Artifact Search", "Advanced Search", "Browse Index", "Refresh Index" Nexus features, as well as Artifact Information tab after selection of any artifact (only Maven Information tab). I tried to Google, but was amazed that there're no information about this issue. Actually it looks like all actions I've done are: wget http://www.sonatype.org/downloads/nexus-2.0.4-1-bundle.tar.gz tar -xvf nexus-2.0.4-1-bundle.tar.gz cp -r nexus-2.0.4-1 sonatype-work /opt/ ln -s /opt/nexus-2.0.4-1/* /opt/nexus ln /opt/nexus/bin/nexus /etc/init.d/ chmod 755 /etc/init.d/nexus vim /etc/init.d/nexus NEXUS_HOME=“/opt/nexus” RUN_AS_USER=“nexus” useradd -s /sbin/nologin -d /var/lib/nexus nexus chown -R nexus /opt/nexus/ chown -R nexus /opt/nexus-2.0.4-1/ sudo -u nexus cp /opt/nexus/conf/examples/proxy-https/jetty.xml /opt/nexus/conf/ To force Nexus be available through HTTPS I went to Administration - Server - Application Server Settings as admin and changed Base URL to https:// external IP/nexus and set Force Base URL to true. Any ideas how to get missed Nexus features?

  Read the article

• MOSS2007 tries to use ActiveDirectory when I have configured an alternative membership provider

  - by glenatron

  I've got a MOSS site that I am trying to configure using Forms authentication and absolutely any kind of membership provider whatsoever. Thus far ActiveDirectory has proved obstructively difficult so I've just whipped up a simple stub membership provider and put it in the GAC. It's a very basic and simple provider but it works fine with an ASP.Net site, I just can't make it work with Sharepoint. On Sharepoint I get the following error when I look for StubProvider:Bob ( or anything else for that matter) from the "Policy For Web Application" people picker: Error in searching user 'StubProvider:bob' : System.ComponentModel.Win32Exception: Unable to contact the global catalog server at Microsoft.SharePoint.Utilities.SPActiveDirectoryDomain.GetDirectorySearcher() at Microsoft.SharePoint.WebControls.PeopleEditor.SearchFromGC(SPActiveDirectoryDomain domain, String strFilter, String[] rgstrProp, Int32 nTimeout, Int32 nSizeLimit, SPUserCollection spUsers, ArrayList& rgResults) at Microsoft.SharePoint.Utilities.SPUserUtility.SearchAgainstAD(String input, SPActiveDirectoryDomain domainController, SPPrincipalType scopes, SPUserCollection usersContainer, Int32 maxCount, String customQuery, TimeSpan searchTimeout, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPActiveDirectoryPrincipalResolver.SearchPrincipals(String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount) at Microsoft.SharePoint.Utilities.SPUtility.SearchPrincipalFromResolvers(List`1 resolvers, String input, SPPrincipalType scopes, SPPrincipalSource sources, SPUserCollection usersContainer, Int32 maxCount, Boolean& reachMaxCount, Dictionary`2 usersDict). The Provider is named as Authentication Provider for the Site Collection in question. As far as I can tell this is because Sharepoint is still trying to access ActiveDirectory rather than talking to the provider I'm asking it to use. My Sharepoint Central Administration section includes this: <membership> <providers> <add name="StubProvider" type="StubMembershipProvider.Provider, StubMembershipProvider, Version=1.0.0.0, Culture=neutral, PublicKeyToken=5bd7e2498c3e1a03" /> </providers> </membership> And also: <PeoplePickerWildcards> <clear /> <add key="StubProvider" value="%" /> </PeoplePickerWildcards> Is there a clear reason why this would not be accessible from the PeoplePicker or why it is still trying to use ActiveDirectory? I've made sure I reset IIS and even restarted the server to see if either of those helped but they made no difference.

  Read the article

• Debian Linux bridging router intermittently dropping packets [migrated]

  - by nomen

  My old Asus router died a few weeks ago, so I thought I'd set up my Debian box to deal with routing my home network. I have a few complications, but I adapted my configuration from a previously working configuration, and I don't see why I am having intermittent problems. But I am having them! Every so often, my SSH connections to the router (and to the Xen virtual machines hosted by the router) just drop. I am unable to use the router's dns server. I can't ping the router. Etc. (I can provide more details, but I'm not sure what will be helpful) /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # Gigabit ethernet, internal network auto eth0 allow-hotplug eth0 iface eth0 inet manual # USB ethernet, internet auto eth1 allow-hotplug eth1 iface eth1 inet dhcp # Xen Bridge auto xlan0 iface xlan0 inet static bridge_ports eth0 address 10.47.94.1 netmask 255.255.255.0 As I understand it, this is sufficient to create the network interfaces, and even do some switching between Xen hosts and my eth0 interface. I installed and configured Shorewall to manage routing: /etc/shorewall/zones fw firewall net ipv4 lan ipv4 /etc/shorewall/interfaces net eth1 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians lan xlan0 detect dhcp,tcpflags,nosmurfs,routefilter,logmartians,routeback,bridge /etc/shorewall/policy net all DROP info fw net ACCEPT info all all REJECT info /etc/shorewall/rules DNS(ACCEPT) fw net DNS(ACCEPT) lan fw ... and so on, these all work, when the router is accepting traffic at all. /etc/shorewall/masq eth1 10.47.94.0/24 Can anybody help?

  Read the article

• How to make Exchange 2003 non-authoritive

  - by Romski

  Background We are a small company with an internally hosted Exchange 2003. It receives email for 2 domains (the company was renamed a few years back). For the sake of argument, the domains are: oldname.com newname.com We have moved newname.com to a hosted exchange service, and our DNS record is correctly routing emails. Our internal server still receives email for oldname.com, although we have asked our hosting company to accept emails for that domain. Problem My problem is that emails generated internally from monitoring software, printer, etc. are being caught by our (defunct) internal server and being delivered to the old mailboxes. I believe that what is happening is that our internal exchange server considers itself to be the authoritive server for newname.com. I think it must be looking in active directory for a mailbox and delivering it internally without ever going outside. Attempt to fix I started to follow the article here: http://support.microsoft.com/kb/321721. I removed the SMTP recipient policy for newname.com, and added a dummy address and made it primary. I also answered yes for updating the associated emails. I then restarted the Microsoft Exchange Routing System and SMTP, but emails are still being routed internally. Is there a way to force the exchange server to route all emails for the domain newname.com to the new hosted service?

  Read the article

• How to connect a VM running on an ESXi host to that host via a VMKernel NIC?

  - by Zac B

  Say I have an ESXi (5.0) host that runs a Linux distribution which hosts iSCSI targets, which contain the images for other VMs which the host will run. When it's used, I'll start the host first, then the iSCSI server, and then refresh all storage targets/HBAs in order to see the provided shares as online. I know it's a strange puzzle-box solution, but I was told to implement it. The ESXi host itself has a gigabit NIC which connects to the outside world. The guest OS (CentOS) supports VMXNet3, however, and if I can, I'd like to use its VMXNET3 NIC to host iSCSI for the ESXi host. How should I go about doing this? I went to create a new virtual network, and selected "VKernel", as it suggested that I use that type of network for SAN traffic, but it is apparently not set up for "self-hosted" SAN hosts, as the new network did not appear as an option to attach the CentOS box's VMXNET3 NIC to. How should I best connect an iSCSI host out to its "parent" ESXi host, if I need a) a 10gb connection, and (optionally) b) a VMKernel network for it?

  Read the article

• Apache2 random 403 error & info server busy logs on Ubuntu

  - by risyasin

  Hello, I have a strange situation with apache2. Meanless, random 403 errors. Any page (html, php etc.) normally working. but if i request repeatedly by pressing refresh button of browser. it interrupts & sends a 403 randomly. after a few seconds it works again. in the error log, i see client denied by server configuration. main error log of apache says [info] server seems busy, (you may need to increase StartServers, or Min/MaxSpareServers), spawning 8 children, there are 99 idle, and 137 total children my current values IfModule mpm_prefork_module StartServers 120 MinSpareServers 100 MaxSpareServers 200 MaxClients 256 MaxRequestsPerChild 500 /IfModule i've increased 10 by 10. from 20. but nothing solved. i've disabled KeepAlive. What may cause this problem ? thank you in advance. a fresh install Ubuntu server x86 8.04.4 Virtualmin from it's website (not from debian repositories). Linux 2.6.24-27-server #1 SMP i686 - Apache 2.2.8 Mpm prefork Virtualmin version 3.78.gpl GPL PHP Version 5.2.4-2ubuntu5.10 Loaded modules: core_module (static) log_config_module (static) logio_module (static) mpm_prefork_module (static) http_module (static) so_module (static) actions_module shared) alias_module (shared) auth_basic_module (shared) auth_digest_module (shared) uthn_file_module (shared) authz_default_module (shared) authz_groupfile_module (shared) uthz_host_module (shared) authz_user_module (shared) autoindex_module (shared) ache_module shared) cgi_module (shared) deflate_module (shared) dir_module (shared) env_module (shared) expires_module (shared) fcgid_module (shared) file_cache_module (shared) eaders_module (shared) mime_module (shared) mime_magic_module (shared) evasive20_module shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) etenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK

  Read the article

• How do I only dp or do just the lines, not the entire block in Vim diff?

  - by hobbes3

  I'm currently using MacVim (Snapshot 64) "Split Diff by..." menu option. The file is Django's my settings.py from version 1.3.1 to a fresh file from version 1.4. (Open the image on a separate window/tab to enlarge.) I know two basic commands do to "obtain" (and replace) a block from the other side. dp to "put" (and replace) a block to the other side. But those two commands writes the entire block, which in MacVim is the purple highlights. If you look at the 2nd block, you can see that from line 2 and 3 only has 2 words that are different: mysite and hobbes3. I just want to replace per line not the entire block. So what is there a command to replace do do and dp per line as oppose to an entire block or do I have to manually type it out? Bonus question: I noticed that once I manually edit a block, I lose the purple highlighting. How do I "refresh" the diff again to include the highlights without reopening the file? Please try to keep the answers Vim-general as oppose to MacVim-specific. Thanks!

  Read the article

• What is the latest on Microsoft Expression Studio licensing?

  - by DanM

  In the past, there's been an issue with Microsoft not allowing you to deactivate an Expression Studio key. Basically, you get two keys per license. If you assign both keys (say one to a desktop and one to a laptop), then you upgrade to a new machine (say you replace your laptop or upgrade some of the hardware), you have to buy a new copy of Expression Studio ($600 for Ultimate). This seems ludicrous to me, and I'm wondering if anyone knows if this policy is still in place. I can't seem to find a EULA online anywhere, so I don't know where to find this information. I know my laptop is due for replacement soon, and I want to know if I'm going to have to sink $600 into a software product I already purchased. For background, please refer to this thread on the Microsoft Expression forums: http://social.expression.microsoft.com/Forums/en-US/general/thread/da5587bc-b098-4c6a-9a56-af3608d940d0 Note that this thread is locked. Microsoft doesn't seem to want people to discuss this. This is one reason I'm posting here rather than on that site.

  Read the article

• Windows XP mounting USB drive to same letter as previously mapped network drive

  - by GAThrawn

  Why does Windows always mount a USB drive as the next drive letter after the last physical drive, even when that letter is already taken by a mapped drive, and is there any way to improve this behaviour? What happens is I tend to use a few different flash drives on my PC, as well as having both a Blackberry and a personal phone that mount as USB drives when I plug them in to charge. Being on a corporate PC I also have a number of mapped network drives (some set by login script, some set as persistent mappings in my profile). When I first login I'll have drive letters like this: C: - Local Drive D: - DVD Drive G: - Login script mapped drive J: - Login script mapped drive When I plug the Blackberry in it'll mount two drives (one for onboard storage, one for the SD card) as E: and F:. If I then plug in another USB drive it will mount as G:, even though that's already taken by a network mapped drive. This leaves me with the following drives: C: - Local Drive D: - DVD Drive E: - USB drive (Blackberry) F: - USB drive (Blackberry) G: - Login script mapped drive [G: - USB drive - mounted but not visible in Explorer or command prompt] J: - Login script mapped drive I then have to go into Disk Management, find the new USB drive that's mounted to G: and re-assign it to another letter eg Z:, once this is done Auto-Play detects it and throws up its normal dialog, and its browseable in Explorer. While this is OK to do if you only use one or two USB drives and have admin access to your PC with your login account, its a total pain in the proverbial if you regularly use a whole load of different USB devices, and corporate policy means you have one account for your normal login (that only has User access to workstations), but have to use a different account for any privileged action. I realize that one possible reason for this is the difference between hardware which is mounted and assigned drive letters at the systen level, and mapped drives which are done at the user level. For USB devices that are already plugged in before login, then obviously they're mounted before Windows knows what network drives may be mapped. However if you plug the USB devices in after you're fully logged in and have drives mapped then Windows must know which letters are available?

  Read the article

• Mod disk_cache permanent caching images and disabling reacurring header updates

  - by user135532

  I am trying to get mod disk_cache to permantly cache images retrieved from an image server on the webserver using ProxyPass. While the image is being retrieved correctly from the server and is served from the cache on further requests, then I am still having the webserver call the image server and causing the cached header to be updated. Because of load concerns then I need to never call the image server on a specific url again after it has been cached once, or extend the refresh time for as long as possible. The webserver is IHS 7.0 The mod's are mod_disk_cache.so, mod_cache.so, mod_proxy.so Version 2.2.8.0 Following is from my httpd.conf: ProxyPass /webserver/media/images/ http://imageserver.com/ws/media/images/ # Caching pictures <IfModule mod_cache.c> <IfModule mod_disk_cache.c> CacheDefaultExpire 2628000 #CacheDisable CacheEnable disk /webserver/media/images/ CacheIgnoreCacheControl On CacheIgnoreHeaders Cookie Referer User-Agent X-Forwarded-For X-Forwarded-Host X-Forwarded-Server Accept-Language Accept Host CacheIgnoreNoLastMod On CacheIgnoreQueryString Off #CacheIgnoreURLSessionIdentifiers CacheLastModifiedFactor 10000000.1 #CacheLock on #CacheLockMaxAge 5 #CacheLockPath CacheMaxExpire 1576800 CacheStoreNoStore On CacheStorePrivate On CacheDirLength 2 CacheDirLevels 3 CacheMaxFileSize 1000000 CacheMinFileSize 1 CacheRoot c:/cacheroot2 </IfModule> </IfModule>

  Read the article

• iis7 large worker process request queue creating process blocking aspnet.config & machine.config amended (bottleneck)

  - by scott_lotus

  ASP.net 2.0 app .net 2.0 framework IIS7 I am seeing a large queue of "requests" appear under the "worker process" option. State recorded appear to be Authenticate Request and Execute Request Handles more than anything else. I have amended aspnet.config in C:\Windows\Microsoft.NET\Framework64\v2.0.50727 (32 bit path and 64 bit path) to include: maxConcurrentRequestsPerCPU="50000" maxConcurrentThreadsPerCPU="0" requestQueueLimit="50000" I have amended machine.config in C:\Windows\Microsoft.NET\Framework64\v2.0.50727\CONFIG (32 bit and 64 bit path) to include: autoConfig="true" maxIoThreads="100" maxWorkerThreads="100" minIoThreads="50" minWorkerThreads="50" minFreeThreads="176" minLocalRequestFreeThreads="152" Still i get the issue. The issue manifestes itself as a large number of processes in the Worker Process queue. Number of current connections to the website display 500 when this issue occurs. I dont think i have seen concurrent connections over 500 without this issue occurring. Web application slows as the request block. Refreshing the app pool resolves for a while (as expected) as the load is spread between the two pools. Application pool in question FIXED REQUEST have been set to refresh on 50000. Thank you for any help. Scott quick edit to say hmm, my develeopers are telling me the project was built with .net 3.5 framework. Looking at C:\Windows\Microsoft.NET\Framework64\v3.5 there does not appear to be a ASPNET.CONFIG or a MACHINE.CONFIG .... is there a 3.5 equivalent ? after a little searching apparenetly 3.5 uses the 2.0 framework files that 3.5 is missing. So back to the original question , where is my bottleneck ?

  Read the article

• Can't resolve offline file conflicts

  - by Bryan

  We use roaming profiles on our Server 2008 R2 domain, with folder redirection for 'desktop', 'my documents' and 'application data'. But as our network is split across two sites, we have one file server at each site, which are configured to use domain based DFS namespaces and DFS replication to keep things in sync. The DFS path for the replication folder is as follows: \\domain\folderredirection$\<username>\<redirected-folder-name> The real paths are \\site-1-server\folderredirection$\<username>\<redirected-folder-name> and \\site-2-server\folderredirection$\<username>\<redirected-folder-name> As our users all switch between sites (sometimes several time per day), our folder redirection policy has to redirect to the DFS roots rather than hardcoded to a specific server. Both DFS and DFS-R have been proven to be working perfectly. On our laptops, we use offline files for the redirected folders, and this also works fine, however the problem is as follows: When conflicts occur in offline files, it is impossible to resolve the conflicts. I'm given the usual conflict resolution options (i.e. 'Ignore', 'Keep Both', 'Keep network' and 'Keep local'), however, not one of these options will resolve any conflict, yet no error is produced. We only use offline files on laptops, which have either Windows XP Professional or Windows 7 Professional installed. The problem is not specific to any one laptop, it affects every laptop and every conflicting file in exactly the same way. I would have thought the set up we have is common for companies that have multiple sites, so I'm hoping someone will have seen this before?

  Read the article

• DNS zone file SPF configuration to support sending mail from multiple servers and gmail

  - by Tauren

  I want to configure SPF on a domain to allow mail to be sent from: the x.com website server (x.com and www.x.com - both at same IP) it's MX servers (smtp.x.com, mx.x.com, mail.x.com) another server that isn't listed as an MX server (somehost.x.com) via gmail using an account that has authenticated use of [email protected] Will this zone file work? If not, what are the problems with it? $ttl 38400 @ IN SOA ns1.x.com. hostmaster.x.com. ( 201003092 ; serial 8H ; refresh 15M ; retry 1W ; expire 1H ) ; minimum @ NS ns1.x.com. @ NS ns2.x.com. @ MX 10 mx.x.com. @ MX 20 smtp.x.com. @ MX 30 mailhost.x.com. ; SPF records @ IN TXT "v=spf1 a mx a:somehost.x.com include:_spf.google.com ~all" mx IN TXT "v=spf1 a -all" smtp IN TXT "v=spf1 a -all" mailhost IN TXT "v=spf1 a -all" Questions: Is _spf.google.com the right thing to include for gmail.com, or is it only for Google Hosted Apps? If only for Google Apps, what should I include to send from gmail.com? If mail shouldn't be sent from anywhere else, is it safe to use -all instead of ~all? Does it make sense to add specific SPF records for each of the mail servers? Any other problems with the zone file? I want to confirm these things before making changes to my zone file. The file has SPF configured basically the same now, just without google.com and somehost, but I want to make sure I won't break things when I change it.

  Read the article

• VNC error: "Could not connect to session bus: Failed to connect to socket"

  - by GJ

  I started a vncserver on display :1 on an ubuntu machine. When I connect to it, I get a grey X window with an error message Could not connect to session bus: Failed to connect to socket. The vnc log is: Xvnc Free Edition 4.1.1 - built Apr 9 2010 15:59:33 Copyright (C) 2002-2005 RealVNC Ltd. See http://www.realvnc.com for information on VNC. Underlying X server release 40300000, The XFree86 Project, Inc Sun Mar 20 15:33:59 2011 vncext: VNC extension running! vncext: Listening for VNC connections on port 5901 vncext: created VNC server for screen 0 error opening security policy file /etc/X11/xserver/SecurityPolicy Could not init font path element /usr/X11R6/lib/X11/fonts/Type1/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/Speedo/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/misc/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/75dpi/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/100dpi/, removing from list! cat: /var/run/gdm/auth-for-link2-eGnVvf/database: No such file or directory gnome-session[24880]: WARNING: Could not make bus activated clients aware of DISPLAY=:1.0 environment variable: Failed to connect to socket /tmp/dbus-FhdHHIq8jt: Connection refused gnome-session[24880]: WARNING: Could not make bus activated clients aware of GNOME_DESKTOP_SESSION_ID=this-is-deprecated environment variable: Failed to connect to socket /tmp/dbus-FhdHHIq8jt: Connection refused gnome-session[24880]: WARNING: Could not make bus activated clients aware of SESSION_MANAGER=local/dell:@/tmp/.ICE-unix/24880,unix/dell:/tmp/.ICE-unix/24880 environment variable: Failed to connect to socket /tmp/dbus-FhdHHIq8jt: Connection refused Sun Mar 20 15:34:10 2011 Connections: accepted: 0.0.0.0::51620 SConnection: Client needs protocol version 3.8 SConnection: Client requests security type VncAuth(2) VNCSConnST: Server default pixel format depth 16 (16bpp) little-endian rgb565 VNCSConnST: Client pixel format depth 16 (16bpp) little-endian rgb565 gnome-session[24880]: Gtk-CRITICAL: gtk_main_quit: assertion `main_loops != NULL' failed gnome-session[24880]: CRITICAL: dbus_g_proxy_new_for_name: assertion `connection != NULL' failed Any ideas how to fix it?

  Read the article

• Disabled FRS replication on a DFS link, but the targets still list the replica set in their FRS conf

  - by Graeme Donaldson

  It's been a while since I've had to deal with the wonders of FRS, so I'm doing some testing to refresh my memory. This is what I've done so far. I am stuck with FRS rather than DFS-R for the moment since not all of my link targets are running R2. Created a domain-based DFS root, hosted on 4 servers. Created a DFS link under the root, targeted at 2 servers. The shares on both servers were empty. Dropped about 500MB of data into the target folder on one server and waited for replication to complete. Added/removed/modified files on both targets and confirmed that changes are replicated within a few seconds. Deleted the contents of the target folder on 1 server and waited for the other server to replicate the deletion. All of this worked perfectly, so now I want to remove my DFS link since I only created it for testing purposes. This is where it gets weird. I'm pretty sure that in the past I've disabled replication on the DFS link and after a short amount of time each target would log an info event in the FRS event log, something along the lines of "this server is no longer a member of replica set X". I have waited about 3 hours and I haven't seen this happen. ntfrsutl ds tells me that the server is not a member of any set, which is expected because when I disable replication on the link, the AD attributes on the computer object are removed. The weird part is... ntfrsutl sets still shows me the replica set, with all the properties, etc. So it seems like the FRS-related attributes of the target server's AD object are gone, but the FRS service for some reason hasn't removed the replica set. Can anyone see what I have done wrong?

  Read the article

• Why can't I copy .zip files from a server to a server in a different domain?

  - by Kyralessa

  At work, we're using a Windows Server 2008 R2 VM as our build server. At the end of the build process for any of our projects, we copy the packaged deployment files to a folder on the server where they'll be deployed. (This is done in a batch command by a service account.) For most of our projects, which deploy to a Windows Server 2008 R2 VM, this step goes swimmingly. But for one project, which deploys to a Windows Server 2003 R2 VM which resides in a different domain on our network, the .zip files return "Access is denied" and don't copy, though all of the other files copy correctly. Our sysadmins say they haven't prevented this in group policy or by other means. If I'm logged in the build server as myself and run the copy in the command window, I can't copy the .zip files over either, so it's not just a matter of the service account's permissions. If I log into the 2003 server and then copy from the build server to the 2003 server, using the command window, it works, whether I run as myself or as our service account. Only .zip files cause the "Access is denied" problem. Even a (fake) .exe file copies correctly. All of our other projects have .zip files, and they copy to their 2008 R2 server correctly. Is there a way I can get the Windows Server 2003 R2 VM to accept .zip files copied from our build server?

  Read the article

• Password Manager that allows syncing accross platforms

  - by lexu

  I use OS X, Linux, Solaris and windows for work and from home. There are good tools that allow me to manage the many logins/passwords required platform independently. But mostly they expect me to carry a thumb-drive around or require direct access to a central location (a sky drive in the cloud). The thumb-drive is too easily lost (= synchronized backup needed), the central location not always reachable/ mountable. Besides company policy rightly prevents this often. Is there a tool that allows me to add passwords locally and then syncs it's DB with the "mother-ship" later. Or is there another approach that you use, that solves my problem? EDIT My question is more about "synchronize" than cross platform. I've evaluated (=read feature list) some good cross platform tools, but need one that does the synchronizing for me. By synchronize I mean "merge two versions" not "replace (hopefully) old file with new." I'm not sure I'm always disciplined/awake enough to prevent data loss. UPDATE Lifehacker just posted that AgileSolutions now have a beta version of 1Password for Windows.

  Read the article

• Bounce backs from web-generated e-mails are missing

  - by JerSchneid

  We use Google Apps to host my company's mail. On our website, we send some e-mails on behalf of our users. In those e-mails we include lines like this: Return-Path: <[email protected]> Sender: <[email protected]> Sending the messages works great (passes SPF tests), but in the case that the message is sent TO an invalid e-mail address, we expect to get a bounce back message sent to "[email protected]". That message never arrives. (If we send an e-mail manually from within the gmail interface to the same bad e-mail, the message does arrive). We used to receive the bounce back messages as expected, but it seems like they are always quietly blocked now (not in spam or anything). Is there a new policy that blocks bounce backs when the "From" does not match the "Return-Path" or something? We would really like to get these bounce-backs to verify the delivery of the messages. Is there any way to prevent them from being blocked?! Thank you!

  Read the article

• Network share not always available on Windows 2003

  - by JP Hellemons

  Hello everybody, we have a windows 2003 server with a shared directory/folder. I've seen this thread but this wasn't any help: http://superuser.com/questions/58890/the-specified-network-name-is-no-longer-available I have a ping -t running from 3 pc's (vista and two windows 7) they all work. the problem occurss when two users enter the network share then this 'network share is no longer available' appears and the explorer windows turn white. after f5 or refresh the shared directory is back. this is really strange. there is no anti virus or kasparsky running on either end. this is all in the same LAN. the internet connection is really stable, so it's really strange. because a stable internet connection should imply that the local network connection is also stable and that this is a windows issue. can it be a router issue? I have checked the eventlog on the server for diskfailure related messages, but there are none. EDIT: can this be related to mapping a shared directory to a drive letter? and that there is a router between me and the mapped network drive? or is it just windows that is not working well with two users on the same shared folder? should I install samba or something?

  Read the article

• How can adding a server to a domain cause Remote Desktop to stop working?

  - by Adrian Grigore

  I have two dedicated with Windows 2008 R2 servers which I am using for Web hosting. One Server A is a domain controller, Server B should simply be added to the domain controlled by Server A. So I RDP'd into Server B and changed the system settings so that Server B is part of that domain. I entered my domain admin credentials, was welcomed to the domain and asked to reboot the server. So far everything seemed to work smoothly After rebooting, I could not open an RDP connection to Server B anymore: Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Make sure the remote computer is turned on and connected to the network, and that remote access is enabled. I restored an older backup of Server B and switched off the firewall before adding the server to my domain. But the problem reoccurred just the same. What could be the reason for this? The domain is brandnew and I did not change any of the default settings. Could this be some kind of domain-wide default policy that shuts down RDP on any domain clients? Or perhaps it has to do with the fact that Server B is virtual? Thanks for your help, Adrian

  Read the article

• Optimum configuration of McAfee for Servers

  - by Wayne Arthurton

  Our corporate standard is McAfee Enterprise, unfortunately this is non-negotiable. On two types of servers I'm responsible for, SQL & Web, we have noticed major performance issues with the corporate standard setup. Max scan time 45sec One policy for all processes Scan ALL files on write, read and open for backup Heuristics: Find unknown programs, trojans and macros Detect unwanted programs Exclude: EVT, LDF, LOG, MDF, VMD, , windows file protection) This of course still causes major slowdowns. IIS .NET recompiles are slow especially with SharePoint, SQL backups and restores, SQL Analysis Services, Integration Services and temp data from them as well. I have looked from time to time, for some best practices on setting up McAfee of SQL & SQL Analysis Service, SQL Integration Service, Visual Studio, Sharepoint, and .NET web servers in general. How do people setup McAfee enterprise on their corporate serves keeping security intact, but affecting performance as minimally as possible? Has anyone run across white papers on these setups? Obviously some are case by case, but there must be some best practices out there somewhere.

  Read the article

• CryptSvc not matched by Windows 7 Firewall rule

  - by theultramage

  I am using Windows Firewall in conjunction with a third-party tool to get notified about new outbound connection attempts (Windows Firewall Notifier or Windows Firewall Control). The way these tools do it is by setting the firewall to deny by default, and to add an auditing policy to log blocked connections into the Security event log. Then they watch the log, and display notification about newly added entries. netsh advfirewall set allprofiles firewallpolicy blockinbound,blockoutbound auditpol /set /subcategory:{0CCE9226-69AE-11D9-BED3-505054503030} /failure:enable With this configuration in place, I now need to craft outbound allow rules for applications and system services. Here is the rule for CryptSvc, the service frequently used for certificate validation and revocation checking: netsh advfirewall firewall add rule name="Windows Cryptographic Services" action=allow enable=yes profile=any program="%SystemRoot%\system32\svchost.exe" service="CryptSvc" dir=out protocol=tcp remoteport=80,443 The problem is, this rule does not work. Unless I change the scope to "all programs and services" (which is really unhealthy), connection denied events like the following will keep appearing in the security log: Event 5157, Microsoft Windows security auditing. The Windows Filtering Platform has blocked a connection. Application Information: Process ID: 1476 (<- svchost.exe with CryptSvc and nothing else) Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Direction: Outbound Source Address: 192.168.0.1 Source Port: 49616 Destination Address: 2.16.52.16 Destination Port: 80 Protocol: 6 (<- TCP) To make sure it's CryptSvc, I have let the connection through and reviewed its traffic; I also configured CryptSvc to run in its own svchost instance to make it more obvious: ;sc config CryptSvc type= share sc config CryptSvc type= own So... why is it not matching the firewall rule, and how to fix that?

  Read the article

< Previous Page | 166 167 168 169 170 171 172 173 174 175 176 177  | Next Page >