Issue with SPI (Serial Port Comm), stuck on ioctl()
- by stef
I'm trying to access a SPI sensor using the SPIDEV driver but my code gets stuck on IOCTL.
I'm running embedded Linux on the SAM9X5EK (mounting AT91SAM9G25). The device is connected to SPI0. I enabled CONFIG_SPI_SPIDEV and CONFIG_SPI_ATMEL in menuconfig and added the proper code to the BSP file:
static struct spi_board_info spidev_board_info[] {
{
.modalias = "spidev",
.max_speed_hz = 1000000,
.bus_num = 0,
.chips_select = 0,
.mode = SPI_MODE_3,
},
...
};
spi_register_board_info(spidev_board_info, ARRAY_SIZE(spidev_board_info));
1MHz is the maximum accepted by the sensor, I tried 500kHz but I get an error during Linux boot (too slow apparently). .bus_num and .chips_select should correct (I also tried all other combinations). SPI_MODE_3 I checked the datasheet for it.
I get no error while booting and devices appear correctly as /dev/spidevX.X. I manage to open the file and obtain a valid file descriptor. I'm now trying to access the device with the following code (inspired by examples I found online).
#define MY_SPIDEV_DELAY_USECS 100
// #define MY_SPIDEV_SPEED_HZ 1000000
#define MY_SPIDEV_BITS_PER_WORD 8
int spidevReadRegister(int fd,
unsigned int num_out_bytes,
unsigned char *out_buffer,
unsigned int num_in_bytes,
unsigned char *in_buffer)
{
struct spi_ioc_transfer mesg[2] = { {0}, };
uint8_t num_tr = 0;
int ret;
// Write data
mesg[0].tx_buf = (unsigned long)out_buffer;
mesg[0].rx_buf = (unsigned long)NULL;
mesg[0].len = num_out_bytes;
// mesg[0].delay_usecs = MY_SPIDEV_DELAY_USECS,
// mesg[0].speed_hz = MY_SPIDEV_SPEED_HZ;
mesg[0].bits_per_word = MY_SPIDEV_BITS_PER_WORD;
mesg[0].cs_change = 0;
num_tr++;
// Read data
mesg[1].tx_buf = (unsigned long)NULL;
mesg[1].rx_buf = (unsigned long)in_buffer;
mesg[1].len = num_in_bytes;
// mesg[1].delay_usecs = MY_SPIDEV_DELAY_USECS,
// mesg[1].speed_hz = MY_SPIDEV_SPEED_HZ;
mesg[1].bits_per_word = MY_SPIDEV_BITS_PER_WORD;
mesg[1].cs_change = 1;
num_tr++;
// Do the actual transmission
if(num_tr > 0)
{
ret = ioctl(fd, SPI_IOC_MESSAGE(num_tr), mesg);
if(ret == -1)
{
printf("Error: %d\n", errno);
return -1;
}
}
return 0;
}
Then I'm using this function:
#define OPTICAL_SENSOR_ADDR "/dev/spidev0.0"
...
int fd;
fd = open(OPTICAL_SENSOR_ADDR, O_RDWR);
if (fd<=0) {
printf("Device not found\n");
exit(1);
}
uint8_t buffer1[1] = {0x3a};
uint8_t buffer2[1] = {0};
spidevReadRegister(fd, 1, buffer1, 1, buffer2);
When I run it, the code get stuck on IOCTL!
I did this way because, in order to read a register on the sensor, I need to send a byte with its address in it and then get the answer back without changing CS (however, when I tried using write() and read() functions, while learning, I got the same result, stuck on them).
I'm aware that specifying .speed_hz causes a ENOPROTOOPT error on Atmel (I checked spidev.c) so I commented that part.
Why does it get stuck? I though it can be as the device is created but it actually doesn't "feel" any hardware. As I wasn't sure if hardware SPI0 corresponded to bus_num 0 or 1, I tried both, but still no success (btw, which one is it?).
UPDATE: I managed to have the SPI working! Half of it.. MOSI is transmitting the right data, but CLK doesn't start... any idea?
