Search Results

Search found 7325 results on 293 pages for 'windows7 32'.

Page 171/293 | < Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >

• Wireless keeps disabling or stays disconnected (Realtek RTL8191SEvB)

  - by jindrichm

  I have Realtek RTL8191SEvB wireless card on Ubuntu 10.10: $ lspci -v | grep Network 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller (rev 10) When I load its driver, according to the Network Manager it sometimes blinks with a list of available networks but it keeps disabling itself or it stays disconnected. So, I can't connect to any wi-fi network (which results in frustration). The driver is loaded: $ lsmod Module Size Used by r8192se_pci 509932 0 Looks normal: $ sudo lshw -C network *-network description: Wireless interface product: RTL8191SEvB Wireless LAN Controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 10 serial: 1c:65:9d:60:c7:7a width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl819xSE driverversion=0019.1207.2010 firmware=63 latency=0 link=no multicast=yes wireless=802.11bgn resources: irq:17 ioport:2000(size=256) memory:f0500000-f0503fff Configured: $ sudo iwconfig wlan0 wlan0 802.11bgn Nickname:"rtl8191SEVA2" Mode:Managed Frequency=2.412 GHz Access Point: Not-Associated Bit Rate:130 Mb/s Retry:on RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=10/100 Signal level=0 dBm Noise level=-100 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Is not blocked: $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: yes However something's happening with it: $ dmesg [ 6485.948668] InitializeAdapter8190(): ==++==> Turn off RF for RfOffReason(1073741824) ---------- [ 6486.062666] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.062671] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.062675] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.064091] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 6486.248761] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1 [ 6486.248771] InitializeAdapter8192SE(): Set MRC settings on as default!! [ 6486.248776] HW_VAR_MRC: Turn on 1T1R MRC! [ 6486.580083] GPIOChangeRF - HW Radio OFF [ 6486.610085] ============>sync_scan_hurryup out [ 6486.623814] ================>r8192_wx_set_scan(): hwradio off [ 6486.830484] =========>r8192_wx_set_essid():hw radio off,or Rf state is eRfOff, return So, does anyone know where the problem might be?

  Read the article

• CodePlex Daily Summary for Sunday, October 28, 2012

  CodePlex Daily Summary for Sunday, October 28, 2012Popular ReleasesPlayer Framework by Microsoft: Player Framework for Windows 8 (Preview 7): This release is compatible with the version of the Smooth Streaming SDK released today (10/26). Release 1 of the player framework is expected to be available next week. IMPROVEMENTS & FIXESIMPORTANT: List of breaking changes from preview 6 Support for the latest smooth streaming SDK. Xaml only: Support for moving any of the UI elements outside the MediaPlayer (e.g. into the appbar). Note: Equivelent changes to the JS version due in coming week. Support for localizing all text used in t...Send multiple SMS via Way2SMS C#: SMS 1.1: Added support for 160by2Quick Launch: Quick Launch 1.0: A Lightweight and Fast Way to Manage and Launch Thousands of Tools and ApplicationsPress Win+Q and start to search and run. http://www.codeplex.com/Download?ProjectName=quicklaunch&DownloadId=523536Orchard Project: Orchard 1.6: Please read our release notes for Orchard 1.6: http://docs.orchardproject.net/Documentation/Orchard-1-6-Release-Notes Please do not post questions as reviews. Questions should be posted in the Discussions tab, where they will usually get promptly responded to. If you post a question as a review, you will pollute the rating, and you won't get an answer.ZXMAK2: Version 2.6.7.0: - small performance improvements - fix & improvements for Direct3D renderer (thanks to zebest for testing)Media Companion: Media Companion 3.507b: Once again, it has been some time since our release, and there have been a number changes since then. It is hoped that these changes will address some of the issues users have been experiencing, and of course, work continues! New Features: Added support for adding Home Movies. Option to sort Movies by votes. Added 'selectedBrowser' preference used when opening links in an external browser. Added option to fallback to getting runtime from the movie file if not available on IMDB. Added new Big...MSBuild Extension Pack: October 2012: Release Blog Post The MSBuild Extension Pack October 2012 release provides a collection of over 475 MSBuild tasks. A high level summary of what the tasks currently cover includes the following: System Items: Active Directory, Certificates, COM+, Console, Date and Time, Drives, Environment Variables, Event Logs, Files and Folders, FTP, GAC, Network, Performance Counters, Registry, Services, Sound Code: Assemblies, AsyncExec, CAB Files, Code Signing, DynamicExecute, File Detokenisation, GUI...NAudio: NAudio 1.6: Release notes at http://mark-dot-net.blogspot.co.uk/2012/10/naudio-16-release-notes-10th.htmlPowerShell Community Extensions: 2.1 Production: PowerShell Community Extensions 2.1 Release NotesOct 25, 2012 This version of PSCX supports both Windows PowerShell 2.0 and 3.0. See the ReleaseNotes.txt download above for more information.Umbraco CMS: Umbraco 4.9.1: Umbraco 4.9.1 is a bugfix release to fix major issues in 4.9.0 BugfixesThe full list of fixes can be found in the issue tracker's filtered results. A summary: Split buttons work again, you can now also scroll easier when the list is too long for the screen Media and Content pickers have information of the full path of the picked item Fixed: Publish status may not be accurate on nodes with large doctypes Fixed: 2 media folders and recycle bins after upgrade to 4.9 The template/code ...AcDown????? - AcDown Downloader Framework: AcDown????? v4.2.2: ??●AcDown??????????、??、??、???????。????，????，?????????????????????????。???????????Acfun、????(Bilibili)、??、??、YouTube、??、???、??????、SF????、????????????。 ●??????AcPlay?????，??????、????????????????。 ● AcDown??????????????????，????????????????????????????。 ● AcDown???????C#??，????.NET Framework 2.0??。?????"Acfun?????"。 ????32??64? Windows XP/Vista/7/8 ???? 32??64? ???Linux ????(1)????????Windows XP???，????????.NET Framework 2.0???(x86)，?????"?????????"??? (2)???????????Linux???，????????Mono?? ??2...Rawr: Rawr 5.0.2: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr Addon (NOT UPDATED YET FOR MOP)We now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including ba...MCEBuddy 2.x: MCEBuddy 2.3.5: Changelog for 2.3.5 (32bit and 64bit) 1. Fixed a bug causing MCEBuddy to crash during or after installation on Windows XP 2. Bugfix for resource leak with UPnP which would lead to a failure after many days 3. Increased the UPnP discovery re-scan interval from 10 minutes to 30 minutes 4. Added support for specifying TVDB and IMDB id’s in the conversion task page (forcing the internet lookup for metadata)CRM 2011 Visual Ribbon Editor: Visual Ribbon Editor (1.3.1025.5): [NEW] Support for connecting to CRM Online via Office 365 (OSDP) [NEW] Current connection information and loaded ribbon name are displayed in the status bar [IMPROVED] Connect dialog minor improvements and error message descriptions [IMPROVED] Connecting to a CRM server will close currently loaded ribbon upon confirmation (if another ribbon was loaded previously) [FIX] Fixed bug in Open Ribbon dialog which would not allow to refresh entity list more than onceReadable Passphrase Generator: KeePass Plugin 0.8.0: Changes: Interrogative phrases (questions) like why did the statesman burgle amidst lucid sunlamps Support transitive / intransitive verbs (whether a verb needs a subject or not). Change adverbs to be either before or after the verb, at random. Add an "equal" version of each strength, where each possibility is equally likely (for password purists). 3401 words in the default dictionary (~400 more than previous release) Fixed bugs when choosing verb tenseseWay payment gateway provider for NB_Store: NB_Store_Gateway_eWay: Install package for eWAY gateway for NB_Store.fastJSON: v2.0.9: - added support for root level DataSet and DataTable deserialize (you have to do ToObject<DataSet>(...) ) - added dataset testsMicrosoft Ajax Minifier: Microsoft Ajax Minifier 4.72: Fix for Issue #18819 - bad optimization of return/assign operator.WPF Application Framework (WAF): WPF Application Framework (WAF) 2.5.0.390: Version 2.5.0.390 (Release Candidate): This release contains the source code of the WPF Application Framework (WAF) and the sample applications. Requirements .NET Framework 4.0 (The package contains a solution file for Visual Studio 2010) The unit test projects require Visual Studio 2010 Professional Changelog Legend: [B] Breaking change; [O] Marked member as obsolete WAF: Fix recent file list remove issue. WAF: Minor code improvements. BookLibrary: Fix Blend design time support o...Fiskalizacija za developere: FiskalizacijaDev 1.1: Ovo je prva nadogradnja ovog projekta nakon inicijalnog predstavljanja - dodali smo nekoliko feature-a, bilo zato što smo sami primijetili da bi ih bilo dobro dodati, bilo na osnovu vaših sugestija - hvala svima koji su se ukljucili :) Ovo su stvari riješene u v1.1.: 1. Bilo bi dobro da se XML dokument koji se šalje u CIS može snimiti u datoteku (http://fiskalizacija.codeplex.com/workitem/612) 2. Podrška za COM DLL (VB6) (http://fiskalizacija.codeplex.com/workitem/613) 3. Podrška za DOS (unu...New ProjectsAnalytics for Windows 8: SIlverlight / WPF User control integrated in WPF / SILVERLIGHT / WINDOWS PHONE Apps in order to collect user data ( Action , Timespan etc ) . bGui - User Interfaces in Batch: A small project for allowing basic user interface creation in batch. Still under strict development, see documentation for current functionality.Blog Projects: Projects wich i use in my blog postsCloud Sync Service: This Windows Service lets you sync your files across other machines by using Cloud File Storage as gateway. Amazon S3 and Windows Azure supported.CocoaVP8: CocoaVP8 is a dual-licensed commercial/GPL native library which allows Mac and iOS applications to easily use the VP8 video codec.DarkSky Orchard Microdata: Microdata is an Orchard module that exposes a MicrodataPart that will render microdata for your content items.Gerenciador Paroquial: Um conjunto de ferramentas desenvolvido para auxiliar a administração de comunidades eclesiásticas episcopais.Quick Launch: Quick Launch - a New Lightweight and Fast Way to Manage and Launch Thousands of Tools and ApplicationsRDI Alef: RDI ALEF (ALef Entities Framework) é uma biblioteca desenvolvida em C# para persistência de objetos em um banco de dados. Encapsula um manipulador SQL e o funciSend multiple SMS via Way2SMS C#: Way2SMS, 160BY2, SMS, INDIATrending: Trending program; calculates the highest and lowest changes in frequency of specific words in two files.

  Read the article

• fwupd to update OCZ RevoDrive firmware gets a 'Permission denied' error

  - by Late

  Try as I might I just don't get it working (http://www.ocztechnology.com/ssd_tools/OCZ_RevoDrive_and_RevoDrive_X2/). There's another thread here with an similar issue here: Command is giving me "bash: ./fwupd: cannot execute binary file" I'm running command ./fwupd /dev/sdb which keeps returning me bash: ./fwupd: Permission denied I have tried running both bit versions available of fwupd with both of the latest 32- and 64-bit Ubunty 11.10, running the OS from an USB stick, but to no avail (could this be the problem?). In the other thread it was suggested that chmod +x fwupd (or chmod 0755 fwupd) should resolve this issue, but at least for me it has been for naught. It was also suggested to install certain libraries, but those were already included in the Ubunty build and I didn't have any luck after updating with apt-get. I also tried giving fwupd more privileges, r, x and w but same charade, run it in different ways from different places (where I'd have the fwupd present, ofc) among other things. What I also tried is giving the Ubunty 10.04 LTS a shot but it didn't even launch on either of my computers, though that's not the issue here. If anyone has any ideas on what the problem is and how I could get this working, it would be most appreciated!

  Read the article

• xubuntu 12.04 screen regularly stops refreshing, refreshing resumes after un-/re-maximizing a window

  - by user68477

  My screen frequently stops completely refreshing. I can make it resume refreshing by un-maximizing/re-maximize a window or by switching workspace (the un-/re-maximizing works every time. Switching workspace sometimes has to be done a couple of times). The immediate impression is that the system is frozen: there is apparently no reaction to anything I do but interestingly window title bar will change, if I switch application with (i.e alt+tab or browse through folders) I saw an identical issue in ubuntu 10.04, though a lot less frequent, I never saw this in ubuntu 12.04 (which I have been using the last 4-5 months). After switching to Xubuntu I'm seeing this again and more frequently. The specific reason I'm not sure this is a bug: I installed gnome-control-center which dragged in tons of packages. This was while trying to fix dual-screen setup. I believe the issue surfaced after this. I later meticulously removed every package from this batch (purge) in the hope that every setting would also be removed. But the issue has persisted. Another issue happened at the same time, it may be totally unrelated but it feels as if it is the same basic issue: the screen resolution of the greeter became less than the expected 1680x1050 and often after login there's just a blank and totally unresponsive wallpaper without panel so I have to force reboot. When the login is successful it's very clear that it works hard to determine the correct resolution which is achieved after a few blink to black screens. My questions: 1) Is this a settings issue or a bug? 2) How do I begin to research the issue - could I perhaps some way reset xubuntu/xfce to default. 3) If this is a bug where would be the most appropriate place report this? System: Thinkpad T500 ati radeon HD 3650 $ fglrxinfo display: :0.0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: ATI Mobility Radeon HD 3650 OpenGL version string: 3.3.11627 Compatibility Profile Context $ uname -a Linux srvname 3.2.0-32-generic #51-Ubuntu SMP Wed Sep 26 21:33:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux xfce 4.10 Compiz 0.9.7.8

  Read the article

• Microsoft Lifecam VX-2000 doesn't work anymore in Cheese

  - by paed808

  I got have two Lifecam VX-2000's and they don't work in cheese anymore. I don't know if it's a problem with a missing package, or a package I installed. Here is the output. (cheese:11122): Clutter-WARNING **: No listener with the specified listener id 29 (cheese:11122): Clutter-WARNING **: No listener with the specified listener id 30 (cheese:11122): Clutter-WARNING **: No listener with the specified listener id 31 (cheese:11122): Clutter-WARNING **: No listener with the specified listener id 32 (cheese:11122): GLib-CRITICAL **: g_hash_table_remove_internal: assertion `hash_table != NULL' failed (cheese:11122): Clutter-WARNING **: Not able to remove listener with id 1 (cheese:11122): GLib-CRITICAL **: g_hash_table_size: assertion `hash_table != NULL' failed totem-video-thumbnailer: 'file:///home/myusername/Videos/Webcam/2012-09-20- 191530.webm' isn't thumbnailable Reason: Media contains no supported video streams. ** (cheese:11122): WARNING **: could not generate thumbnail for /home/myusername/Videos/Webcam/2012-09-20-191530.webm (video/webm) Notice the: Reason: Media contains no supported video streams. When I try to record a video it just makes a 13.2KB WEBM file with nothing. When I take a picture it works. Edit: I've been thinking that the problem started after installing the MediUbuntu repository on my system.

  Read the article

• SSD I/O extremely slow installing/booting Ubuntu 12.04

  - by Menda

  These are some useful specs: Macbook Pro 7,1 OWC Mercury Extreme Pro 2,5" SATA SSD (120 GB). Has SandForce driver. Ubuntu 12.04 Desktop 32 bits. One 18 GB partition for GNU/Linux and 1.5 GB for SWAP. MD5 for the Ubuntu install CD is OK. I tried to install Ubuntu. It seems that everything is recognized, but there's a big problem: read and writes to the SSD are extremely slow. For example, the install process, which shouldn't take more than 20 minutes, it takes 7 hours. Then, booting up the computer takes about 20 minutes. I checked and the problem is definitely the SSD. Every access to any file is like 10 times slower than normal. I have tried to format the partition as Ext4 and Ext3 with the same problem. Trying to install other distros like Fedora 17, I have a similar problem. There's a "lag" with the SSD, but not so accused as in Ubuntu. Surprisingly, Debian 6.0 installs and works without any problem. Mac OS works pretty good as well in the other partition, so I discard it's an SSD problem. Thanks for your help!

  Read the article

• Google+ Platform Office Hours for April 25, 2012: Q&A with the Hangouts API Team

  Google+ Platform Office Hours for April 25, 2012: Q&A with the Hangouts API Team This week we were joined by Richard Dunn of the Hangouts API team who answered questions about the Hangouts API. Discuss this video on Google+: goo.gl 1:09 - What's going on with the Hangouts API? 3:43 - Jason shares information about his current projects 5:40 - Can I prevent a Hangout app from running within a Hangout On Air? 8:05 - Can we have APIs to control On Air features? 10:05 - Could a Silverlight / JavaScript bridge be created so we can use them in Hangout Apps? 12:01 - Is there a way to obfuscate the code for a Hangouts app? 15:24 - Are there plans to consolidate the various comment and chat channels for Hangouts On Air? 18:53 - When will Hangouts On Air come to Android? 20:48 - How can I access the OAuth token from the API? - developers.google.com 22:39 - When will we have Hangout apps on the mobile devices? 24:57 - Is it possible to search for 2 or more hash tags via the search REST API? 25:45 - Will we see a PHP REST API demo today? 26:20 - How can I restrict usage of a Hangout app? 30:07 - How do you hold a hangout that is simulcast on YouTube? 31:07 - Why do users show up as empty objects before they've authorized the app? 32:52 - What are the best practice for storing user specific configuration? 38:06 - Is anyone doing in application payment? 39:22 - Has anyone written any books about Hangout apps? From: GoogleDevelopers Views: 1619 19 ratings Time: 42:04 More in Science & Technology

  Read the article

• Locale variables have no effect in remote shell (perl: warning: Setting locale failed.)

  - by Janning

  I have a fresh ubuntu 12.04 installation. When i connect to my remote server i got errors like this: ~$ ssh example.com sudo aptitude upgrade ... Traceback (most recent call last): File "/usr/bin/apt-listchanges", line 33, in <module> from ALChacks import * File "/usr/share/apt-listchanges/ALChacks.py", line 32, in <module> sys.stderr.write(_("Can't set locale; make sure $LC_* and $LANG are correct!\n")) NameError: name '_' is not defined perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LC_TIME = "de_DE.UTF-8", LC_MONETARY = "de_DE.UTF-8", LC_ADDRESS = "de_DE.UTF-8", LC_TELEPHONE = "de_DE.UTF-8", LC_NAME = "de_DE.UTF-8", LC_MEASUREMENT = "de_DE.UTF-8", LC_IDENTIFICATION = "de_DE.UTF-8", LC_NUMERIC = "de_DE.UTF-8", LC_PAPER = "de_DE.UTF-8", LANG = "en_US.UTF-8" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). locale: Cannot set LC_ALL to default locale: No such file or directory No packages will be installed, upgraded, or removed. 0 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 0 B of archives. After unpacking 0 B will be used. ... I don't have this problem when i connect from an older ubuntu installation. This is output from my ubuntu 12.04 installation, LANG and LANGUAGE are set $ locale LANG=de_DE.UTF-8 LANGUAGE=de_DE:en_GB:en LC_CTYPE="de_DE.UTF-8" LC_NUMERIC=de_DE.UTF-8 LC_TIME=de_DE.UTF-8 LC_COLLATE="de_DE.UTF-8" LC_MONETARY=de_DE.UTF-8 LC_MESSAGES="de_DE.UTF-8" LC_PAPER=de_DE.UTF-8 LC_NAME=de_DE.UTF-8 LC_ADDRESS=de_DE.UTF-8 LC_TELEPHONE=de_DE.UTF-8 LC_MEASUREMENT=de_DE.UTF-8 LC_IDENTIFICATION=de_DE.UTF-8 LC_ALL= Does anybody know what has changed in ubuntu to get this error message on remote servers?

  Read the article

• Ubuntu 11.10 loads from live usb fine, but boots to black screen from harddrive. Why?

  - by Estel

  A few days ago I had a hard drive failure, which was running Windows XP (32-bit) just fine. The second hard drive in my computer held a few unimportant files, so I formatted it in the Ubuntu setup and installed 11.10 without a hitch. I had been using it for about a week, but decided to install Windows 7 (64-bit) in order to utilize Networking with my home server (running Windows Server 2000). My system is 64-bit based, and thus I had no problems installing other than a basic RAM error that required me to remove my RAM down to a single stick. I played with the settings in Windows 7 for around an hour before I shut down. After reinstalling the RAM, Windows 7 would not boot. In this, I then assumed that something about my system was rejecting Win7 and I reinstalled Ubuntu. However, now Ubuntu (11.10) boots into black screen, and I've already attempted activating the grub menu with the shift key, and following steps listed here: https://wiki.ubuntu.com/X/Troubleshooting/BlankScreen but nothing seems to work. I've reinstalled twice now, with the same result each time. Now, the very odd part about this whole scenario is that the USB I installed from has no problems booting as a live USB. This puzzles me greatly, because the hard drive boots straight to black screen and the live USB loads normally. At this point, my only theory is that the boot sector of the hard disk was somehow corrupted with Win7, and that Ubuntu was unable to completely write through. I used Darik's Boot n Nuke to wipe the drive, but was met with an error, this also puzzles me because the hard disk has no promblems reading or writing. Any suggestions/comments are appreciated. If you have a theory, I will be more than happy to oblige. Additional information: Intel Core2 Duo e6400 2.13GHz nVidia GeForce 7-series (7900 GS) 4 GB DDR2 333MHz (2x 2GB) Dell XPS 410 BIOS Revision 2.5.3

  Read the article

• "The volume filesystem root has only..."

  - by jcslzr

  I am having this problem in ubuntu 12.04, but I fin strange that when I go to /tmp it wont allow me to delete some files, with message "Operation not permitted" or "this file could not be handled because you dont have permissions to read it". It is only a PC and I have the root password. I was trying to get at least 2000 MB of free space on the root file system to upgrade to 12.10 and see if that resolved the problem. Currently free space on root file system is 190 MB. This is my output: root@jcsalazar-Vostro-3550:~# df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda6 7688360 7112824 184984 98% / udev 2009288 4 2009284 1% /dev tmpfs 806636 1024 805612 1% /run none 5120 0 5120 0% /run/lock none 2016584 5316 2011268 1% /run/shm /dev/sda5 472036 255920 191745 58% /boot /dev/sda7 30758848 7085480 22110900 25% /home root@jcsalazar-Vostro-3550:~# sudo parted -l Model: ATA TOSHIBA MK3261GS (scsi) Disk /dev/sda: 320GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 106MB 105MB primary fat16 2 106MB 15.8GB 15.7GB primary ntfs boot 3 15.8GB 278GB 262GB primary ntfs 4 278GB 320GB 41.9GB extended 5 278GB 279GB 499MB logical ext4 6 279GB 287GB 7999MB logical ext4 7 287GB 319GB 32.0GB logical ext4 8 319GB 320GB 1443MB logical linux-swap(v1) I apprecciate any new ideas that can help me. Thnx Carlos

  Read the article

• Essbase Analytics Link (EAL) - Performance of some operation of EAL could be improved by tuning of EAL Data Synchronization Server (DSS) parameters

  - by Ahmed Awan

  Generally, performance of some operation of EAL (Essbase Analytics Link) could be improved by tuning of EAL Data Synchronization Server (DSS) parameters. a. Expected that DSS machine will be 64-bit machine with 4-8 cores and 5-8 GB of RAM dedicated to DSS. b. To change DSS configuration - open EAL Configuration Tool on DSS machine.     ->Next:     and define: "Job Units" as <Number of Cores dedicated to DSS> * 1.5 "Max Memory Size" (if this is 64-bit machine) - ~1G for each Job Unit. If DSS machine is 32-bit - max memory size is 2600 MB. "Data Store Size" - depends on number of bridges and volume of HFM applications, but in most cases 50000 MB is enough. This volume should be available in defined "Data Store Dir" driver.   Continue with configuration and finish it. After that, DSS should be restarted to take new definitions.  

  Read the article

• Can't configure 5.1 audio with 12.04

  - by xster

  I have an Intel ALC892 and a Nvidia GT 520m connected to speakers via HDMI. On lspci, I see 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) Subsystem: ZOTAC International (MCO) Ltd. Device a218 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at db400000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel 02:00.1 Audio device: NVIDIA Corporation HDMI Audio stub (rev a1) Subsystem: ZOTAC International (MCO) Ltd. Device 2180 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at db080000 (32-bit, non-prefetchable) [size=16K] Capabilities: [60] Power Management version 3 Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [78] Express Endpoint, MSI 00 Kernel driver in use: snd_hda_intel My alsamixer looks like I enabled pulseaudio configuration file to have 6 channels. My sound setting looks like When I use the test dialog, only front left and right have sounds. If I use alsa in XBMC on a 5.1 video, there's no sound. If I use pulseaudio, only front right and left have sound. I can barely hear any speech since I'm guessing it's mapped to front center. Any clues?

  Read the article

• How can I fix my xvinfo?

  - by YumYumYum

  How can i fix my X server/driver? $ xvinfo X-Video Extension version 2.2 screen #0 no adaptors present Additional info: $ uname -a Linux desktop 2.6.32-33-generic #70-Ubuntu SMP Thu Jul 7 21:13:52 UTC 2011 x86_64 GNU/Linux $ lspci 00:00.0 Host bridge: Intel Corporation Device 0100 (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Sandy Bridge Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:19.0 Ethernet controller: Intel Corporation Device 1503 (rev 05) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4a (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 PCI bridge: Integrated Technology Express, Inc. Device 8892 (rev 10) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) Follow up: It seems in 64-bit its a mess doing existing approach. Therefore, after upgrading to 12.04 64-bit this problems in same hardware is resolved (of-course, i have now other drivers problem)

  Read the article

• Ubuntu 12.04 Very slow especially with Android Studio

  - by Dew

  I have an old laptop with the following specification: Memory: 485 MiB, Processor: Genuine intel CPU T2300 @ 1.66 GHz ×2, OS Type: 32 bit, Disk: 78.1 GB, I installed on it Ubuntu 12.04 LTS and I noticed that the overall system is very slow in responding. I tried to search about that in the internet and I found some articles talking about how to make Ubuntu 12.04 LTS run fast I applied all what they said including download LXDE desktop environment and then nothing different in the system response time. Then I need to develop some android applications so, I download Android Studio (Beta) 0.8.6. The problem became worse than before whenever I tried to open the Android Studio the screen is frozen for some minutes then it took time to download the projects and initialize the work space also, when I tried to move the cursor he is move very slowly. When I tried to run my first application on the AVD it took three hours and still not run yet. I delete the Android Studio and install it again several times, I was trying to solve the problem but still nothing change. Please if you have any suggestions that may help me make my laptop and Android Studio work faster I will appreciate it for you. Thank you in advance.

  Read the article

• Ubuntu 14.04: Fine tuning Touchpad for ThinkPad S431

  - by ramgorur

  I am using Ubuntu 14.04 on Lenovo ThinkPad S431. The touchpad is very bumpy, tricky to use. Slides down with a small touch, sometimes jerks erratically. I have tried to modify the settings in /usr/share/X11/xorg.conf.d/50-synaptics.conf file as below -- Section "InputClass" Identifier "touchpad catchall" Driver "synaptics" MatchIsTouchpad "on" MatchDevicePath "/dev/input/event*" Option "JumpyCursorThreshold" "250" Option "VertResolution" "100" # Option "HorizResolution" "65" # Option "MinSpeed" "1" # Option "MaxSpeed" "1" # Option "AccelerationProfile" "1" # Option "AdaptiveDeceleration" "8" # Option "ConstantDeceleration" "1" # Option "VelocityScale" "128" Option "HorizHysteresis" "150" Option "VertHysteresis" "150" EndSection There are lots of options here, does anyone know how to get a fine-tuned values for the above options (for ThinkPad S431)? The Hysteresis values seems to alleviate the problem a little bit, but failed to get a perfect result. EDIT: According to this bug report for ThinkPad X230 (+X230t), I set these values and quite good for now -- Option "VertResolution" "100" Option "HorizResolution" "65" Option "MinSpeed" "1" Option "MaxSpeed" "1" Option "AccelerationProfile" "2" Option "AdaptiveDeceleration" "16" Option "ConstantDeceleration" "16" Option "VelocityScale" "32" Option "HorizHysteresis" "50" Option "VertHysteresis" "50" and then you need to increase the cursor speed manually from the Unity mouse settings. But I am still looking for a fully functional (possibly with all the gestures) and a fine-tuned touchpad settings for S431. Further help is appreciated.

  Read the article

• Is there a NVIDIA driver (for a 7-series card) that will actually work for 12.10?

  - by DS13

  I see many similar topics on this, but I've tried all their suggestions, and nothing has worked. ISSUE: I do a clean install of Ubuntu 12.10. Boots fine with the “nouveau” graphics driver – graphics are very slow and choppy. The three other driver options in Ubuntu (official NVIDIA drivers), all result in a variation of the black screen on boot up. There will be NO access to a command line/GUI in anyway what-so-ever (tried every option recommended out there, but the system is unusable at this stage). I can only reinstall, and try different drivers…and I only ever get one shot at it. QUESTIONS: Does anyone know of a NVIDIA driver that will actually work with a Nvidia GeForce 7350LE? Or a 7-series card in general? This is my second computer, and I’m just trying to get a working install of Ubuntu on it. I don’t want to put much money into it, as I have seen Ubuntu run great on much older/less capable machines. I’ve got a decent Intel processor (2.3Ghz), 2GB of RAM, 320GB hard drive, 32-bit architecture, and there is no other O/S installed. It appears as if the graphics card is holding me back. Should I just buy a cheap graphics card (non-NVIDIA) to put in as a replacement? TRIED SO FAR: -all drivers available in Ubuntu *all fail -manual install of some different NVIDIA drivers *all fail -also tried installing the generic kernel, Nvidia driver doesn't work in 12.10 *no difference -every method suggested to at least get a command line after switching to a NVIDIA driver *all fail

  Read the article

• Is it viable to make a port from a C++ application to Java through LLVM

  - by Javier Mr

  how viable is it to port a C++ application to Java bytecode using LLVM (I guess LLJVM)? The thing is that we currently have a process written in C++ but a new client has made mandatory to been able to run the program in a multiplatform way, using the Java Virtual Machine with obviously no native code (no JNI). The idea is to be able to take the generated jar and copy then to different systems (Linux, Win, 32 bits - 64 bits) and it should just work. Looking around looks like it is possible to compile C++ to LLVM IR code and then that code to java bytecode. There is no need of the generated code to be readable. I have test a bit with similar things using emscripten, this takes C++ code and compile it to JavaScript. The result is valid JS but totally unreadable (looks like assambler). Does anybody done a port of an application from C++ to Java bytecode using this tecnique? What problems could we face? Is a valid approach for production code? Note: I am aware that currently we have some non standard C++ and close source libraries, we are looking to removing this non standard code and all close source libraries and use Free Libre Open Source Software, so lets suppose all code is standard C++ code with all code available at compile time. Note: It is not an option to write portable C++ code and then compile it to the desired target platform, the compiled program must be mltiplatform thus the use of JVM (right now we are not looking in similar solutions but Python or other language base, but i would also like to heard about it)

  Read the article

• aplay -l says no soundcards found; alsaconf says no supported cords; yet /proc/asound contains cards

  - by nimasmi

  I am trying to get HDMI output using a Gainward Nvidia 210 512 MB on Ubuntu 10.04 Lucid Lynx. I have upgraded alsa-driver, alsa-lib and alsa-utils to 1.0.24 by building from source, thanks to this blog post. Some relevant output... user@box:~$ lspci | grep Audio 00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2) 01:09.0 Multimedia video controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder (rev 05) 01:09.2 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] (rev 05) 01:09.4 Multimedia controller: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] (rev 05) 02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) user@box:~$ cat /proc/asound/version Advanced Linux Sound Architecture Driver Version 1.0.24. Compiled on Sep 15 2012 for kernel 2.6.32-42-generic (SMP). user@box:~$ ls /proc/asound` card0 cards hwdep NVidia oss seq version card1 devices modules NVidia_1 pcm timers user@box:~$ aplay -l aplay: device_list:240: no soundcards found... user@box:~$ sudo /sbin/alsa-utils start * Setting up ALSA... * warning: 'alsactl restore' failed with error message 'alsactl: set_control:1403: Cannot write control '2:0:0:IEC958 Playback Default:0' : Operation not permitted'... amixer: Invalid command! ...done. Any help appreciated. PS my video card is connected only through the PCI-E slot. I assume there is no extra audio connection required.

  Read the article

• Problems after installing a plethora of updates

  - by box

  yesterday I decided to install 32-bit Ubuntu on my 64-bit desktop, first of all, is that a problem? After installing, i had around 270 updates to install, according to the update manager. I was having trouble launching a game with WINE, so I thought updating might help. After updating, I restarted my computer, and after a long while it showed me my desktop and the icon's on it, but I didn't get anything else. I didn't have the "taskbar" (not sure what it's called, sue me) on the left side, nor the bar at the top. I also received an error message saying some program had stopped working. I decided to restart my computer again, and that was when it told me that i have to re-configure my drivers, or run in "Low Graphics" mode for one session, amongst other options. Well, I decided to try to revert to the "basic video drivers", which was an option it gave. Restarting the computer gave me the same problem as in the second paragraph. After a few more restarts and a night of restless sleep, here I am trying to start my computer again, only to receive a black screen, and my monitor "going to sleep". I'm sort of stumped here, being new to Ubuntu (desktop, at least) and I really hope this gets fixed without me having to install Ubuntu on yet another partition (I have three other partitions for various things already) tl;dr: Black screen on boot after installing updates.

  Read the article

• How to remove all associated files and configuration settings of an app installed through 'force architecture' command

  - by Mysterio

  A few weeks ago I installed a 32 bit .deb file through the 'force architecture' command (on my 64bit notebook), however the procedure was unsuccessful and I used the apt-get purgecommand to uninstall the app. It seems there are some leftovers of the app I uninstalled which has now broken system update. Synaptic recommended a sudo apt-get install -fwhich I did in the terminal with this initial response: Reading package lists... Done Building dependency tree Reading state information... Done The following package was automatically installed and is no longer required: libntfs10 Use 'apt-get autoremove' to remove them. The following packages will be REMOVED: crossplatformui 0 upgraded, 0 newly installed, 1 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? I chose 'Y' then got this response: (Reading database ... 187616 files and directories currently installed.) Removing crossplatformui ... ztemtvcdromd: no process found dpkg: error processing crossplatformui (--remove): subprocess installed post-removal script returned error exit status 1 Errors were encountered while processing: crossplatformui E: Sub-process /usr/bin/dpkg returned an error code (1) It seems the app I installed crossplatformuiis still on my system and has caused update manager to stop running with a partial upgrade warning. What do I do now?

  Read the article

• Lenovo v570 ubuntu 12.04 wireless hard blocked even when ext. switch is on

  - by user100987

  When I run iwconfig it say's lo and eth0 have no wireless extensions, but wlan0 it says IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS the:off Fragment the:off Power Management:off and I believe that's my problem, I just don't know how to turn it back on Any help? When I ran lspci | grep Network it gave me this 02:00.0 Network controller: Intell Corporation Centrino Wireless -N + WiMAX 6150 (rev 67) How I know that my wireless is hard blocked because when I run sudo rfkill list all I get 0: Ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes when I run lshw -c network I get. *-network DISABLED description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: mon1 version: 67 serial: 40:25:c2:d2:96:2c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-32-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: f0:de:f1:d7:a0:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.65 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff

  Read the article

• Getting error message when trying to start a virtual machine

  - by Sunil J

  I have been using VMWare on Windows for a long time. But after a long wait, I moved to VirtualBox on Ubuntu 11.10. I installed Ubuntu, 32 Bit, installed all available updates and installed Virtual Box. When I try to create a new Windows installation inside VirtualBox, I got the following error messages. 1st error dialogue VirtualBox - Error Failed to open a session for the virtual machine Windows XP.<br> The virtual machine '**Windows XP**' has terminated unexpectedly during startup with exit code 1.<p> Details<p> Result Code: <br> NS_ERROR_FAILURE (0x80004005)<br> Component: <br> Machine<br> Interface: <br> IMachine {5eaa9319-62fc-4b0a-843c-0cb1940f8a91}<p> 2nd error dialogue **Virtualbox - Error in suplibOsinit**<br> **Kernal driver not installed (rc--1908)**<br> Please install the virtualbox-dkmbs package and execute 'modprobe vboxdrv' as root.<p> Steps I tried I have already tried reinstalling VirtualBox. Google result seem to indicate the the problem happens due to Kernel updates. Is there anyway I can get this working? I need this for malware analysis and if VirtualBox is going to crash on me all the time, then I won't be able to use Ubuntu for work. Output to dpkg -l | grep virtual server rc virtualbox 4.1.2-dfsg-1ubuntu1 x86 virtualization solution - base binaries rc virtualbox-qt 4.1.2-dfsg-1ubuntu1 x86 virtualization solution - Qt based user interface cute 'modprobe vboxdrv' as root.<p>

  Read the article

• 12.04 Taking forever for no apparent reason

  - by Sam

  First off, I'd just like to say how much I'm loving Ubuntu so far. It's one of my first steps into Linux, but so far it's blown away Windows in almost every regard. Now, onto my problem. My brothers have some old Dell Dimensions that are barely clinging to life. They were both running XP Home Premium. The 2400 installed just fine, no issues at all. Now, the other computer, the 3000 isn't clearing the screen with the Ubuntu logo and the pulsing dots. I've tried multiple discs, including the exact same one that gave me no issue in the other computer, and I'm at a loss. Does anyone have any suggestions as to where the problem might lay? They're both 32 bit Intel processors, and it's the correct version of Ubuntu. Is it a bad disc drive? Hardware incompatibility? Thanks for any assistance that can be provided. Dell Dimension 2400 Dell Dimension 3000

  Read the article

• Create an array from mysql with column names and values [on hold]

  - by ScaZ

  i'm trying to create an array with PHP and MySQL, but i always get errors. The code i'm using function db_listar_usuarios(){ $link=db_connect(); $query = "select * from usuarios" or die("Problemas en el select: " . mysqli_error($link)); $result = $link->query($query); while($row = mysqli_fetch_assoc($result)) { $row['nombre'] . array(; foreach ($row as $col => $val) { $col => $val; } } } And what I want to create with this code is: array( 'john' => array('address' => 'st 123', 'age' => '25', 'surname' => 'doe'), 'ane' => array('address' => 'av 456', 'age'=> '32', 'surname' => 'smith'), ); To use then like something like this: private $contacts = db_listar_usuarios(); I use 2 files: functions.php and server.php server.php is a downloaded file example to do a REST API. Here are both of them. server.php - pastebin.com/5j54m1Mz functions.php - pastebin.com/N7jMhSBa Thank you in advance!

  Read the article

• Robust way to keep records of software releases?

  - by japreiss

  We release a number of small plug-ins that go along with our software. Each plug-in allows our software to talk to a single manufactuer's hardware. I would like to devise a system for keeping track of plug-in releases. Example info that should be stored: Hardware manufacturer name 32-bit? 64-bit? both? What modes of operation does the hardware support? What versions of the manufacturer's driver have been tested with the plugin? Desirable properties of the system: Able to synchronize with version control software Stores data in human-readable text file (also good for differ tool) Free visual, spreadsheet-like editor available Able to do simple analysis like "What is the oldest plug-in?" I've got to imagine that someone else has tackled this problem already. Right now my best guess is XML/JSON with a visual editor, but I have been disappointed in the editors I've tried so far. I'd like to get input from some more experienced developers. Thanks!

  Read the article

< Previous Page | 167 168 169 170 171 172 173 174 175 176 177 178  | Next Page >