Search Results

Search found 11687 results on 468 pages for 'ex networking guy'.

Page 172/468 | < Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >

  • VirtualBox with Ubuntu Server guest can't ping outside

    - by Danidan
    Here's my situation: an Ubuntu 12.04 Host running VirtualBox; two guest VMs running Ubuntu Server 12.04 home network, so my Host pc has a wireless connection to the router of my ISP. My problem is in one of the virtual machines: it has 3 NICs, one in NAT mode and the others in Host Only mode. My purpose is to use eth0 (NAT) for Internet access and eth1, eth2 (Host Only) for management of internal virtual network (eth1 uses a VBoxNet with this IP 192.168.69.254). Whenever I try to $ping 8.8.8.8 I get Destination Host Unreachable. While if I $ping 192.168.69.10, that is the IP of the other VM, it works. I can't also ping my Host nor my router My /etc/network/interfaces file is: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp auto eth1 iface eth1 inet static address 192.168.69.1 netmask 255.255.255.0 auto eth2 iface ifconfig $IFACE 0.0.0.0 up up ip link set $IFACE promisc on down ip link set $IFASE promisc off down ifconfig $IFACE down $route -n returns: Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.2.2 0.0.0.0 UG 100 0 0 eth0 10.0.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.69.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 Forgetting for now what eth2 needs to do and its setup, why I can't go outside the Host box? What can I do to help you helping me? :-)

    Read the article

  • Internet connection sharing windows server 2008 R2

    - by This is it
    I have one windows server 2008 r2, and that server has 4 network interfaces (3 private, 1 internet connection). I would like to share internet connection with other 3 networks. Windows server firewall should make logs of data that is transfered. It should not be possible to connect directly to private networks from internet. How could I do it? Edit: I tried with NAT in RRAS, but it doesn't work. Here is the configuration: Server: IP private:192.168.0.1 IP public: xx.xx.xx.xx client IP:192.168.0.2 Default gateway: 192.168.0.1 Public and private interface added in NAT section of RRAS.

    Read the article

  • VLSM help required

    - by user68062
    I have confused myself following a VLSM tutorial and need to get my understanding confirmed, would this be the correct format, or am i away off again 172.31.0.0 VLSM this network address for as many subnetworks as possible, with no more than 14 hosts in each subnetwork. Show the subnet mask used. As the ip address is class b and contains 16 bits in the network portion, this means that we can have 2^16 = 65536 possible networks, to give each of these networks a maximum of 14 hosts we would use the subnet prefix \28 for each subnet. Is this correct? Thanks BB

    Read the article

  • VirtualBox cloned Ubuntu Server network error

    - by Luke
    I run a number of virtual servers on my network and I want to be able to easily clone base installations of Ubuntu Server. I use the VBoxManage command to clone the actual hard disk and I then create a new profile for my VM and copy over the settings of the original VM. However, when I boot into the cloned VM, there seems to be a network problem. When I issue a PING I get the message "Network unreachable". I traced it down to the fact that the virtual network card of the cloned VM has a different MAC address then the original VM. When I copy the MAC address the clone seems to work fine. How can I have the cloned VM have it's own MAC address?

    Read the article

  • Kickstarting an Ubuntu Server 10.04 installation (DHCP fails)

    - by William
    I'm trying to automate the network installation of Ubuntu 10.04 LTS with an anaconda kickstart and everything seems to running except for the initial DHCP autoconfiguration. The installer attempts to configure the install via DHCP but fails on its first attempt. This brings me to a prompt where I can retry DHCP and it seems to always work on the second attempt. My issue is that this is not really automated if I have to hit retry for DHCP. Is there something I can add to the kickstart file so that it will automatically retry or better yet not fail the first time? Thanks. Kickstart: # System language lang en_US # Language modules to install langsupport en_US # System keyboard keyboard us # System mouse mouse # System timezone timezone America/New_York # Root password rootpw --iscrypted $1$unrsWyF2$B0W.k2h1roBSSFmUDsW0r/ # Initial user user --disabled # Reboot after installation reboot # Use text mode install text # Install OS instead of upgrade install # Use Web installation url --url=http://10.16.0.1/cobbler/ks_mirror/ubuntu-10.04-x86_64/ # System bootloader configuration bootloader --location=mbr # Clear the Master Boot Record zerombr yes # Partition clearing information clearpart --all --initlabel # Disk partitioning information part swap --size 512 part / --fstype ext3 --size 1 --grow # System authorization infomation auth --useshadow --enablemd5 %include /tmp/pre_install_ubuntu_network_config # Always install the server kernel. preseed --owner d-i base-installer/kernel/override-image string linux-server # Install the Ubuntu Server seed. preseed --owner tasksel tasksel/force-tasks string server # Firewall configuration firewall --disabled # Do not configure the X Window System skipx %pre wget "http://10.16.0.1/cblr/svc/op/trig/mode/pre/system/Test-D" -O /dev/null # Network information # Start pre_install_network_config generated code # Start of code to match cobbler system interfaces to physical interfaces by their mac addresses # Start eth0 # Configuring eth0 (00:1A:64:36:B1:C8) if ip -o link show | grep -i 00:1A:64:36:B1:C8 then IFNAME=$(ip -o link show | grep -i 00:1A:64:36:B1:C8 | cut -d" " -f2 | tr -d :) echo "network --device=$IFNAME --bootproto=dhcp" >> /tmp/pre_install_ubuntu_network_config fi # End pre_install_network_config generated code %packages openssh-server

    Read the article

  • Accessing VMware Player across the network

    - by Tiffany Walker
    My network: 192.168.2.2 (computer) 255.255.255.0 (mask) 192.168.2.254 (gateway) The VMplayer is: 192.168.233.129 (ip) 255.255.255.0 (mask) 192.168.233.255(bcast) It's obvious the player can't be access from other systems because of the wrong network settings. However, I am not sure as to how to change that. Obviously I have to edit the ifcg-eth0 but I know I also need to edit it on the host system to make it accessably. Is this done from inside VMware Player? Or do I need to edit the network devices? The host box is Windows. Inside VMware is Linux.

    Read the article

  • How can I start hostednetwork on Windows 7?

    - by Pirozek
    When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

    Read the article

  • How to set the network profile of Windows 7 via group policy?

    - by Ricket
    We are deploying client computers and in testing noticed that the first time the user logs into the computer, it asks them if the location is a home, work, or public location. We are worried that some users in our workplace might misread it (or not read it at all) and click Public, thus likely denying our access to the computer and messing up security settings and such. Can we set our network to be a "Work Network" location via group policy or some other mechanism of our Windows Domain so that the user is not prompted when connected to our network? Also these are laptops, so we don't want every network they connect to be set as work network, and we have several access points (wired and three wireless) which our users often switch between so I'm not yet sure if it reprompts with each access point but I have the feeling it will, and I would like all of these to be set to the Work profile type.

    Read the article

  • Computer Loses connection to router

    - by ajon
    I have a new Windows 8 Dell XPS desktop computer at work. It has a Dell Wireless 1703 802.11 b/g/n (2.4ghz) wireless adapter. sporadically throughout the day I lose internet connectivity. When I click on the wireless system tray icon, my companies router does not appear in the list. No other computer on the network is losing connection, only this one. I don't even know what to check. Could it be an ip conflict that causes me to get booted off? (I use DHCP), but why wouldn't my computer be able to see the network. The next time it happens I will see what happens when I try to access the router directly.

    Read the article

  • Mirror your display to another computer on your network

    - by klikkamongo
    I have a computer I am using for showing media, running windows 7 (XBMC). It is hooked up with a projector. I want other computers on my network to have the opportunity to mirror their display to this computer.(without the media computer having to accept it, it should be all controlled by the sending computer.(like sending a movie with Apple's Airplay)) One scenario: I am finding a webpage with a great article (or a Word document) on my computer that i want to show to the other people in the room, i press a button, then my screen is mirrored to the media pc. I can still scroll, write etc. so everybody can see it. When i am done showing the article, I can exit the display mirroring, and the media computer display goes back to normal. This should mirror the whole screen, not only the browser like plugins can do in chrome, or sending Youtube movies like plugins for Opera. Update I found a video example of the solution I am looking for, unfortunately it looks like it will be hard making a Chromecast reciever for windows. Using the "Cast entire screen (experimentally)" button on the Chromecast plugin in Chrome is doing the exact thing I want to do, see this video.

    Read the article

  • Cannot connect to MySQL on RDS (Amazon Web Services) from my laptop

    - by Bruno Reis
    I'm having some trouble connecting to a MySQL 5.1 server on an RDS instance on AWS from my laptop. The detailed description of the problem is here: https://forums.aws.amazon.com/thread.jspa?messageID=323397 In short: I have 2 MySQL servers, both with the same db configuration and firewall (security group) configuration. One of them works fine: I can connect to it from my EC2 instances (ie, from inside the AWS cloud) and from my laptop. The other one doesn't: I can connect from my EC2 instances but not from my laptop. The symptom: a connection attempt from my laptop just hangs, and then times out, as if there was a firewall blocking me (ie, silently dropping my SYN packets). I must say that everything has been working fine for a very long time, and this problem began suddenly, 3 days ago, without any modifications to DB parameters or the security groups. My current analysis of the situation: The firewall (ie, security group) cannot be the problem: both MySQL servers share the same firewall configuration -- I can connect to one of them but not to the other. Later on, I even added a rule to allow inbound connections from 0.0.0.0/0 (ie, I turned off the firewall), and nothing. Oh, I also created a new, fresh security group and changed this instance's SG to the new one (to which I first added my ip address, and then 0.0.0.0/0) but still nothing. The credentials cannot be the problem: I use the same from my laptop and from my EC2 instances -- and the user (which is what Amazon calls master user), in the database, has a host of '%'. MySQL is not blocking my IP due to, say, too many failed connection attemps: I've FLUSH HOSTS on the database, and also I tried to connect using many different source IP addresses, even from all around the world through a VPN proxy service. What could I be missing? I'm asking here because it's been about 36 hours since I've posted on AWS forums but got no answer at all over there... someone here might have a solution! Any input is really appreciated, I'm out of ideas. Thanks!

    Read the article

  • My Laptop (HP/Compaq 2510p) running ubuntu 10.04 LTS keeps losing the WLAN connection.

    - by Ernelli
    I am using Wicd and can successfully connect to my ADSL router (Thomson TG 787) using WPA PSK. But with regular interval I lose the ability to connect to Internet. I can ping the GW and can actually ping servers on the Internet but not connect to them using HTTP (Tested with both Firefox and wget). I would suspect the router unless for the fact that the problem does not show up when running Windows XP on the same computer and also, when the problem arises, a simple disconnect/connect in Wicd solves the problem, which does not involve the router (Except for the DHCP request). I have searched Ubuntu forums without luck, most problems described relate to specific network drivers or other problems. Does anyone have the same experience with Linux/Ubuntu and WLAN?

    Read the article

  • Windows Server 2008 R2 - Can't connect RDP over the Internet

    - by Jonathan DeMarks
    I have two networks: Domain and Public, Domain is a VPN connection and Public is the local connection to the network. This is not a domain controller or a DNS/DHCP server. I can connect via RDP from the local network (192.168.1.), from the VPN network (10.1.2.), and from the VPN network over the internet. I cannot connect from the internet (anywhere besides where the server is VPN'd) Wireshark indicates that the server is getting packets, and the audit log is indicating that the packets are being dropped. Advanced Firewall has explicit options to allow RDP, and has no deny policies. I have also tried turning Firewall off completely to no avail. I'm really lost on this one.

    Read the article

  • Share ADSL Internet connection between two computers 40 meters away (straight) from each other

    - by dario_ramos
    I have a box with a working ADSL Internet connection. About 40 meters away (straight), in another house, there is another, older box. There are two houses in between. Would there be some practical way to supply an Internet connection to the older box? The neighbors are ok with us installing cables and stuff. I'd say wifi would not be practical, since the houses in between would weaken the signal too much. And using Ethernet cables might require a switch or router in between, due to Ethernet distance limitations. Advice?

    Read the article

  • Sharing a USB wireless-g adaptor between two computers

    - by cornjuliox
    I've got two computers here that need to connect via wireless-g usb adapter to the same network for internet access but only one USB adapter. Both PCs are using Windows XP, and I have no crossover cables. I've got both computers wired up to a router, and the PC with the active internet connection has ICS enabled, but the second PC gets no internet. Any ideas?

    Read the article

  • Do I need to create static routes for my home network?

    - by SZU
    50.x.x.x assigned by Frontier 192.168.1.1 Actiontec (FiosModem/Router) 192.168.1.2 Voip 192.168.1.3 DLINK/DIR615 (WirelesRouter) 192.168.1.3 assigned by Actiontec 192.168.2.1 DLINK DIR615 (Hardwired to Actiontec) 192.168.2.194 Android 192.168.2.195 Vista-PC1 192.168.2.196 WIN7-PC2 192.168.2.197 Linksys-1 WRT54G/DDWRT(WirelessClient) 192.168.2.198 Linksys-2 WRT54G/DDWRT(WirelessClient) 192.168.2.199 DSi 192.168.2.197 assigned by DLINK 192.168.3.1 Linksys-1 WRT54G/DDWRT 192.168.3.100 Vista-PC3 192.168.2.198 assigned by DLINK 192.168.4.1 Linksys-2 WRT54G/DDWRT 192.168.4.100 Ubuntu-PC4 Above is my current setup. All PCs have Internet access. PC3 and PC4 cannot see each other and PC1/PC2 cannot see PC3/PC4. Do I need static routes between PC3 & PC4, PC1/PC2 & PC3/PC4? If how do I create the static routes?

    Read the article

  • Network router and switch configuration

    - by gilly3
    Can I put a switch before my router in my home network? Here is a diagram of how I want to set up my network: ________________________________ ________________________________________ | | | | | Cable Access Panel | | Home Office | | _____________ ________ | | _____________ | | | | | | | | | | _________ | | | Cable Modem |--->| Switch |-------------->| Router |____| | | | |_____________| |________| | | |_____________| | Printer | | |______________________/____\____| | / | \ |_________| | ___/_ _\___ | _____/ ____|____ \_____ | | | | | | | | | | | | | | PC1 | | PC2 | | | PC3 | | Ext. HD | | PC4 | | |_____| |_____| | |_____| |_________| |_____| | |________________________________________| The reason I want to do this is because my router is also my wireless access point. My cable modem is located in the far corner of my home where my phone/tv/network access panel is. I'd rather keep the wireless access point in a more central location, but I'm not sure if DHCP will continue to work properly with that configuration. Edit: I'd like to continue to be able to share files and access my networked drive and printer from each computer in the house.

    Read the article

  • How to control DVR connected cameras as IP Cameras

    - by Ajay
    We have analog IR cameras (not IP Cameras) and they are connected to DVR model no is (DVR Model: DVR H264, 16 Channel - ECOR264-16X1). We assigned a static IP to DVR and able to view all the cameras connected to it. Our requirement is to view individual cameras and recording option in remote location (the recorded data should store in remote) as like IP Cameras. Is it possible, if not, are there any DVR Model which can support like this.

    Read the article

  • good PCI-e Wireless card for Windows7?

    - by benwebdev
    Hi I've just build a 64bit Windows 7 PC but am unhappy with the piddly performance of the linksys USB wireless dingle I've used. Can anyone suggest a good PCIe alternative that will be stronger for connection and maybe faster. I dont see why my desktop should show a weaker performance on wireless than my laptop when its sat next to it or even my Palm Pre for that matter. any thoughts? UK based max around £60ish. thanks, Ben

    Read the article

  • Stack Managed Switches over a distance

    - by Joel Coel
    We have several buildings with stacked switches, where the distance between the stacked units is considerable... separate floors, or at opposite ends of a hallway. They are 3Com switches that stack using cat6 cabling. These switches are coming up on 12 years old now, and as I look around at replacements it seems no one supports this scenario any more. Stacking switches want to use fiber links (it more for me to run and terminate the fiber stacking cables than to purchase the switch) or other custom cables that seem only intended to jump up to the next unit in a rack. What have others done to support stacking over a distance? I'm considering breaking up the stacked switches into separate managed entities and just bridging from the root switch in the buildings, but I'd really like to avoid that for what I hope are obvious reason. The closest thing I've found are from netgear that use hdmi cables for the stacking connection... I could try to support that by running an additional cat6 line and re-terminating both links into a single hdmi port, but I have concerns over that approach as well.

    Read the article

  • Why are the external IP of my router not the same as the external IP of my computer

    - by Martin
    I have a standard network setup where all my network devices, both WIFI and ethernet, are connected to the same router. Lately, however, I've been experiencing some very strange behavior. It started as a simple connecting error, when I tried to reach an FTP server using the external IP. Of course I went right into one of those CheckMyIP sites, to double check the IP and it turned out to be correct. Then I went into my router setup, which is through a tool called aiport-tool, because I have an Apple Aiport Extreme router. Turns out the router displays a different external IP, and for some reason that external IP works when I try to access the FTP server. Can anyone explain what is going on? Why are the devices connected to the router displaying an incorrect external IP? BTW i have no VPN/proxy setups on any of my devices.

    Read the article

  • Suggestion of device WiFi range in it's spec. Possible?

    - by SeeR
    I have router Draytek Vigor 2100VG at home almost in the center of it. The farthest point at my home is my balcony, ~12m from it. I have constant wifi signal range problems with some of my devices, but not with others. Notebook Lenovo W510 - no problems Nokia Home Music - always on 10m - no problems Sony PS3 - always on 7m - no problems Sony tablet S - problems around 6m Sony PSP - problems around 8m Sony PS Vita - problems around 8m Nokia E63 - problems around 8m I'm curious why my Notebook don't have any problems even on the balcony? I guess it has better hardware or uses more power for transmission. This information is really important when you want to buy new device/computer, so my real question is: Can device wifi range can somehow be found/suggested from official hardware technical specification? If not Is there some web page with wifi range reviews?

    Read the article

  • IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

    - by NVRAM
    I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

    Read the article

  • Virtual box host-only adapter configuration

    - by Xoundboy
    I have VirtualBox 4 running on Win 7 with a Centos 6 guest VM set up for hosting my dev server. When I'm connected to my home network the guest can be accessed via a static IP address that I configured (192.168.56.2), but not when I'm in the office. I'm guessing that the DHCP server in the office doesn't have a gateway configured for the 192.168.56.x IP range. I read something about the VB host-only adapter that should allow me to set this guest VM up in such a way that I don't need to be on any network to be able to access the guest from the host using a static IP. I've not been able to find out exactly how to configure this though. Can anyone give me an example configuration, thanks. UPDATE: Thanks for your responses. I've now set up a single virtual network adapter in VirtualBox and set it to host-only: C:\Users\Ben>vboxmanage list hostonlyifs Name: VirtualBox Host-Only Ethernet Adapter GUID: d419ef62-3c46-4525-ad2d-be506c90459a Dhcp: Disabled IPAddress: 192.168.56.2 NetworkMask: 255.255.255.0 IPV6Address: fe80:0000:0000:0000:78e3:b200:5af3:2a57 IPV6NetworkMaskPrefixLength: 64 HardwareAddress: 08:00:27:00:94:e8 MediumType: Ethernet Status: Up VBoxNetworkName: HostInterfaceNetworking-VirtualBox Host-Only Ethernet Adapter On the guest I've set up eth0 to use the same IP address as the host-only adapter (192.168.56.2) but when I try to log in using Putty I still get "Network Error : connection refused". VirtualBox DHCP servier is enabled but I can't ping the gateway (192.168.56.1) from either host nor guest. There's no firewall running on either OS. What next?

    Read the article

  • How to route local traffic over switch?

    - by Franz Kafka
    I'm just cabled up at home but haven't got any way of verifying that gigabit speed can be reached. As I've only got one laptop with one network card, one cable, and one switch, I'm kind of stuck. I'm using a tool that you can start as a server or as a client to send data from one box to another. I would like to send and receive on the same Windows box. I guess if I use my network local IP address, my Windows 8.1 PC will just route traffic internally. Is there some way of forcing the traffic to go to the switch and back again?

    Read the article

< Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >